Lines Matching defs:set
109 * need to set this)
234 * from Beacon frame). After the first set of IEs, another set of IEs may follow
326 * The frequency is set in MHz. The array is zero-terminated.
366 * When set, the driver is expected to remove rates 1, 2, 5.5, and 11
396 * a multicast one, i.e., bit 0 of byte 0 should not be set.
406 * must be set.
674 * for fast transition, this parameter is set to include the IEs that
703 * to the current mobility domain. This value is set to %NULL if no
712 * only for drivers that set WPA_DRIVER_FLAGS_4WAY_HANDSHAKE. This is
723 * only for drivers that set WPA_DRIVER_FLAGS_4WAY_HANDSHAKE. This is
791 * Only bits set in the mask will be used, and not all values are used
883 * This parameter can be used to set a specific basic rate set for the
884 * BSS. If %NULL, default basic rate set is used.
992 * not set (e.g., when 802.11g mode is not in use)
1007 * hessid - Homogeneous ESS identifier or %NULL if not set
1333 int set; /* Set STA parameters instead of add */
1454 WNM_SLEEP_TFS_REQ_IE_SET, /* AP requests driver to set TFS req IE for
1459 WNM_SLEEP_TFS_RESP_IE_SET, /* AP requests driver to set TFS resp IE
1561 * %WMM_PARAMS_UAPSD_QUEUES_INFO is set)
1674 * keys and set to zero for unicast keys); %NULL if not set
1689 * it as the default Tx key (set_tx is set) and accept Rx for all the
1900 * space applications. This function, if set, gets called with
1909 * @addr: Address of the station for which to set protection (may be
1915 * This is an optional function that can be used to set the driver to
1919 * set protection operation; instead, they set protection implicitly
2079 * template or the set of additional IEs (e.g., WPS and P2P IE).
2124 * enable/disable IEEE 802.1X support and set WPA/WPA2 parameters. This
2125 * can be left undefined (set to %NULL) if IEEE 802.1X support is
2126 * always enabled and the driver uses set_ap() to set WPA/RSN IE
2140 * kernel driver for Beacon frames. This can be left undefined (set to
2184 * undefined (set to %NULL) if the driver uses the Beacon template from
2297 * With TDLS, this function is also used to add or set (params->set 1)
2346 * @total_flags: Bitmap of all WPA_STA_* flags currently set
2424 * network interface up) at the end of initial configuration. If set,
2472 * Beacon and Probe Response frames. This can be left undefined (set
2532 * If the %WPA_DRIVER_FLAGS_OFFCHANNEL_TX flag is set, the frame will
2536 * If the flag is not set, the wait time will be ignored. In this case,
2552 * set in the driver flags.
2666 * @encrypt: Whether to encrypt the frame (if keys are set)
2696 * This function is used to set Notice of Absence parameters for GO. It
2697 * is used only for testing. To disable NoA, all parameters are set to
2810 * @attr: Bridge port attribute to set
2811 * @val: Value to be set
2819 * @param: Bridge parameter to set
2820 * @val: Value to be set
2846 * This function can be used to set authentication algorithms for AP
3104 * @freq: If set, survey data for the specified frequency is only
3105 * being requested. If not set, all survey data is requested.
3139 * @bssid: Forced BSSID if roaming is disabled or %NULL if not set
3143 * associate() command (bssid being set there indicates that the driver
3502 * This event can be used to inform wpa_supplicant about desire to set
3505 * STAKey negotiation. The caller will need to set peer address for the
3532 * the STA and set up encryption keys with it.
3846 * This event indicates a set of frequency ranges that should be avoided
3971 * set, the results from previous scan will be used. If no
4289 * If not set to NULL, this is used for comparison with