bugreportz.cpp revision 2628e9e939fda323fa44c5cb743f4a77b12a312a
1/* 2 * Copyright (C) 2016 The Android Open Source Project 3 * 4 * Licensed under the Apache License, Version 2.0 (the "License"); 5 * you may not use this file except in compliance with the License. 6 * You may obtain a copy of the License at 7 * 8 * http://www.apache.org/licenses/LICENSE-2.0 9 * 10 * Unless required by applicable law or agreed to in writing, software 11 * distributed under the License is distributed on an "AS IS" BASIS, 12 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. 13 * See the License for the specific language governing permissions and 14 * limitations under the License. 15 */ 16 17#include <errno.h> 18#include <stdio.h> 19#include <sys/socket.h> 20#include <sys/types.h> 21#include <unistd.h> 22 23#include <cutils/properties.h> 24#include <cutils/sockets.h> 25 26// TODO: code below was copy-and-pasted from bugreport.cpp (except by the timeout value); 27// should be reused instead. 28int main() { 29 30 // Start the dumpstatez service. 31 property_set("ctl.start", "dumpstatez"); 32 33 // Socket will not be available until service starts. 34 int s; 35 for (int i = 0; i < 20; i++) { 36 s = socket_local_client("dumpstate", ANDROID_SOCKET_NAMESPACE_RESERVED, SOCK_STREAM); 37 if (s >= 0) 38 break; 39 // Try again in 1 second. 40 sleep(1); 41 } 42 43 if (s == -1) { 44 printf("Failed to connect to dumpstatez service: %s\n", strerror(errno)); 45 return 1; 46 } 47 48 // Set a timeout so that if nothing is read in 10 minutes, we'll stop 49 // reading and quit. No timeout in dumpstate is longer than 60 seconds, 50 // so this gives lots of leeway in case of unforeseen time outs. 51 struct timeval tv; 52 tv.tv_sec = 10 * 60; 53 tv.tv_usec = 0; 54 if (setsockopt(s, SOL_SOCKET, SO_RCVTIMEO, &tv, sizeof(tv)) == -1) { 55 printf("WARNING: Cannot set socket timeout: %s\n", strerror(errno)); 56 } 57 58 while (1) { 59 char buffer[65536]; 60 ssize_t bytes_read = TEMP_FAILURE_RETRY( 61 read(s, buffer, sizeof(buffer))); 62 if (bytes_read == 0) { 63 break; 64 } else if (bytes_read == -1) { 65 // EAGAIN really means time out, so change the errno. 66 if (errno == EAGAIN) { 67 errno = ETIMEDOUT; 68 } 69 printf("\nBugreport read terminated abnormally (%s).\n", 70 strerror(errno)); 71 break; 72 } 73 74 ssize_t bytes_to_send = bytes_read; 75 ssize_t bytes_written; 76 do { 77 bytes_written = TEMP_FAILURE_RETRY( 78 write(STDOUT_FILENO, buffer + bytes_read - bytes_to_send, 79 bytes_to_send)); 80 if (bytes_written == -1) { 81 printf( 82 "Failed to write data to stdout: read %zd, trying to send %zd (%s)\n", 83 bytes_read, bytes_to_send, strerror(errno)); 84 return 1; 85 } 86 bytes_to_send -= bytes_written; 87 } while (bytes_written != 0 && bytes_to_send > 0); 88 } 89 90 close(s); 91 return 0; 92 93} 94