1/* 2 * Copyright (c) 2007-2018 Douglas Gilbert. 3 * All rights reserved. 4 * Use of this source code is governed by a BSD-style 5 * license that can be found in the BSD_LICENSE file. 6 */ 7 8#include <stdlib.h> 9 10#ifdef HAVE_CONFIG_H 11#include "config.h" 12#else 13#define SG_SCSI_STRINGS 1 14#endif 15 16#include "sg_lib.h" 17#include "sg_lib_data.h" 18 19 20const char * sg_lib_version_str = "2.38 20180122";/* spc5r17, sbc4r15 */ 21 22 23/* indexed by pdt; those that map to own index do not decay */ 24int sg_lib_pdt_decay_arr[32] = { 25 PDT_DISK, PDT_TAPE, PDT_TAPE /* printer */, PDT_PROCESSOR, 26 PDT_DISK /* WO */, PDT_MMC, PDT_SCANNER, PDT_DISK /* optical */, 27 PDT_MCHANGER, PDT_COMMS, 0xa, 0xb, 28 PDT_SAC, PDT_SES, PDT_DISK /* rbc */, PDT_OCRW, 29 PDT_BCC, PDT_OSD, PDT_TAPE /* adc */, PDT_SMD, 30 PDT_DISK /* zbc */, 0x15, 0x16, 0x17, 31 0x18, 0x19, 0x1a, 0x1b, 0x1c, 0x1d, PDT_WLUN, PDT_UNKNOWN 32}; 33 34#ifdef SG_SCSI_STRINGS 35struct sg_lib_value_name_t sg_lib_normal_opcodes[] = { 36 {0, 0, "Test Unit Ready"}, 37 {0x1, 0, "Rezero Unit"}, 38 {0x1, PDT_TAPE, "Rewind"}, 39 {0x3, 0, "Request Sense"}, 40 {0x4, 0, "Format Unit"}, 41 {0x4, PDT_TAPE, "Format medium"}, 42 {0x4, PDT_PRINTER, "Format"}, 43 {0x5, 0, "Read Block Limits"}, 44 {0x7, 0, "Reassign Blocks"}, 45 {0x7, PDT_MCHANGER, "Initialize element status"}, 46 {0x8, 0, "Read(6)"}, /* obsolete in sbc3r30 */ 47 {0x8, PDT_PROCESSOR, "Receive"}, 48 {0xa, 0, "Write(6)"}, /* obsolete in sbc3r30 */ 49 {0xa, PDT_PRINTER, "Print"}, 50 {0xa, PDT_PROCESSOR, "Send"}, 51 {0xb, 0, "Seek(6)"}, 52 {0xb, PDT_TAPE, "Set capacity"}, 53 {0xb, PDT_PRINTER, "Slew and print"}, 54 {0xf, 0, "Read reverse(6)"}, 55 {0x10, 0, "Write filemarks(6)"}, 56 {0x10, PDT_PRINTER, "Synchronize buffer"}, 57 {0x11, 0, "Space(6)"}, 58 {0x12, 0, "Inquiry"}, 59 {0x13, 0, "Verify(6)"}, /* SSC */ 60 {0x14, 0, "Recover buffered data"}, 61 {0x15, 0, "Mode select(6)"}, /* SBC-3 r31 recommends Mode select(10) */ 62 {0x16, 0, "Reserve(6)"}, /* obsolete in SPC-4 r11 */ 63 {0x16, PDT_MCHANGER, "Reserve element(6)"}, 64 {0x17, 0, "Release(6)"}, /* obsolete in SPC-4 r11 */ 65 {0x17, PDT_MCHANGER, "Release element(6)"}, 66 {0x18, 0, "Copy"}, /* obsolete in SPC-4 r11 */ 67 {0x19, 0, "Erase(6)"}, 68 {0x1a, 0, "Mode sense(6)"}, /* SBC-3 r31 recommends Mode sense(10) */ 69 {0x1b, 0, "Start stop unit"}, 70 {0x1b, PDT_TAPE, "Load unload"}, 71 {0x1b, PDT_ADC, "Load unload"}, 72 {0x1b, PDT_PRINTER, "Stop print"}, 73 {0x1c, 0, "Receive diagnostic results"}, 74 {0x1d, 0, "Send diagnostic"}, 75 {0x1e, 0, "Prevent allow medium removal"}, 76 {0x23, 0, "Read Format capacities"}, 77 {0x24, 0, "Set window"}, 78 {0x25, 0, "Read capacity(10)"}, 79 /* SBC-3 r31 recommends Read capacity(16) */ 80 {0x25, PDT_OCRW, "Read card capacity"}, 81 {0x28, 0, "Read(10)"}, /* SBC-3 r31 recommends Read(16) */ 82 {0x29, 0, "Read generation"}, 83 {0x2a, 0, "Write(10)"}, /* SBC-3 r31 recommends Write(16) */ 84 {0x2b, 0, "Seek(10)"}, 85 {0x2b, PDT_TAPE, "Locate(10)"}, 86 {0x2b, PDT_MCHANGER, "Position to element"}, 87 {0x2c, 0, "Erase(10)"}, 88 {0x2d, 0, "Read updated block"}, 89 {0x2e, 0, "Write and verify(10)"}, 90 /* SBC-3 r31 recommends Write and verify(16) */ 91 {0x2f, 0, "Verify(10)"}, /* SBC-3 r31 recommends Verify(16) */ 92 {0x30, 0, "Search data high(10)"}, 93 {0x31, 0, "Search data equal(10)"}, 94 {0x32, 0, "Search data low(10)"}, 95 {0x33, 0, "Set limits(10)"}, 96 {0x34, 0, "Pre-fetch(10)"}, /* SBC-3 r31 recommends Pre-fetch(16) */ 97 {0x34, PDT_TAPE, "Read position"}, 98 {0x35, 0, "Synchronize cache(10)"}, 99 /* SBC-3 r31 recommends Synchronize cache(16) */ 100 {0x36, 0, "Lock unlock cache(10)"}, 101 {0x37, 0, "Read defect data(10)"}, 102 /* SBC-3 r31 recommends Read defect data(12) */ 103 {0x37, PDT_MCHANGER, "Initialize element status with range"}, 104 {0x38, 0, "Medium scan"}, 105 {0x39, 0, "Compare"}, /* obsolete in SPC-4 r11 */ 106 {0x3a, 0, "Copy and verify"}, /* obsolete in SPC-4 r11 */ 107 {0x3b, 0, "Write buffer"}, 108 {0x3c, 0, "Read buffer(10)"}, 109 {0x3d, 0, "Update block"}, 110 {0x3e, 0, "Read long(10)"}, /* obsolete in SBC-4 r7 */ 111 {0x3f, 0, "Write long(10)"}, /* SBC-3 r31 recommends Write long(16) */ 112 {0x40, 0, "Change definition"}, /* obsolete in SPC-4 r11 */ 113 {0x41, 0, "Write same(10)"}, /* SBC-3 r31 recommends Write same(16) */ 114 {0x42, 0, "Unmap"}, /* added SPC-4 rev 18 */ 115 {0x42, PDT_MMC, "Read sub-channel"}, 116 {0x43, PDT_MMC, "Read TOC/PMA/ATIP"}, 117 {0x44, 0, "Report density support"}, 118 {0x45, PDT_MMC, "Play audio(10)"}, 119 {0x46, PDT_MMC, "Get configuration"}, 120 {0x47, PDT_MMC, "Play audio msf"}, 121 {0x48, 0, "Sanitize"}, 122 {0x4a, PDT_MMC, "Get event status notification"}, 123 {0x4b, PDT_MMC, "Pause/resume"}, 124 {0x4c, 0, "Log select"}, 125 {0x4d, 0, "Log sense"}, 126 {0x4e, 0, "Stop play/scan"}, 127 {0x50, 0, "Xdwrite(10)"}, /* obsolete in SBC-3 r31 */ 128 {0x51, 0, "Xpwrite(10)"}, /* obsolete in SBC-4 r15 */ 129 {0x51, PDT_MMC, "Read disk information"}, 130 {0x52, 0, "Xdread(10)"}, /* obsolete in SBC-3 r31 */ 131 {0x52, PDT_MMC, "Read track information"}, 132 {0x53, 0, "Xdwriteread(10)"}, /* obsolete in SBC-4 r15 */ 133 {0x54, 0, "Send OPC information"}, 134 {0x55, 0, "Mode select(10)"}, 135 {0x56, 0, "Reserve(10)"}, /* obsolete in SPC-4 r11 */ 136 {0x56, PDT_MCHANGER, "Reserve element(10)"}, 137 {0x57, 0, "Release(10)"}, /* obsolete in SPC-4 r11 */ 138 {0x57, PDT_MCHANGER, "Release element(10)"}, 139 {0x58, 0, "Repair track"}, 140 {0x5a, 0, "Mode sense(10)"}, 141 {0x5b, 0, "Close track/session"}, 142 {0x5c, 0, "Read buffer capacity"}, 143 {0x5d, 0, "Send cue sheet"}, 144 {0x5e, 0, "Persistent reserve in"}, 145 {0x5f, 0, "Persistent reserve out"}, 146 {0x7e, 0, "Extended cdb (XCBD)"}, /* added in SPC-4 r12 */ 147 {0x80, 0, "Xdwrite extended(16)"}, /* obsolete in SBC-4 r15 */ 148 {0x80, PDT_TAPE, "Write filemarks(16)"}, 149 {0x81, 0, "Rebuild(16)"}, 150 {0x81, PDT_TAPE, "Read reverse(16)"}, 151 {0x82, 0, "Regenerate(16)"}, 152 {0x83, 0, "Third party copy out"}, /* Extended copy, before spc4r34 */ 153 /* Following was "Receive copy results", before spc4r34 */ 154 {0x84, 0, "Third party copy in"}, 155 {0x85, 0, "ATA pass-through(16)"}, /* was 0x98 in spc3 rev21c */ 156 {0x86, 0, "Access control in"}, 157 {0x87, 0, "Access control out"}, 158 {0x88, 0, "Read(16)"}, 159 {0x89, 0, "Compare and write"}, 160 {0x8a, 0, "Write(16)"}, 161 {0x8b, 0, "Orwrite(16)"}, 162 {0x8c, 0, "Read attribute"}, 163 {0x8d, 0, "Write attribute"}, 164 {0x8e, 0, "Write and verify(16)"}, 165 {0x8f, 0, "Verify(16)"}, 166 {0x90, 0, "Pre-fetch(16)"}, 167 {0x91, 0, "Synchronize cache(16)"}, 168 {0x91, PDT_TAPE, "Space(16)"}, 169 {0x92, 0, "Lock unlock cache(16)"}, 170 {0x92, PDT_TAPE, "Locate(16)"}, 171 {0x93, 0, "Write same(16)"}, 172 {0x93, PDT_TAPE, "Erase(16)"}, 173 {0x94, PDT_ZBC, "ZBC out"}, /* new sbc4r04, has service actions */ 174 {0x95, PDT_ZBC, "ZBC in"}, /* new sbc4r04, has service actions */ 175 {0x9a, 0, "Write stream(16)"}, /* added sbc4r07 */ 176 {0x9b, 0, "Read buffer(16)"}, /* added spc5r02 */ 177 {0x9c, 0, "Write atomic(16)"}, 178 {0x9d, 0, "Service action bidirectional"}, /* added spc4r35 */ 179 {0x9e, 0, "Service action in(16)"}, 180 {0x9f, 0, "Service action out(16)"}, 181 {0xa0, 0, "Report luns"}, 182 {0xa1, 0, "ATA pass-through(12)"}, 183 {0xa1, PDT_MMC, "Blank"}, 184 {0xa2, 0, "Security protocol in"}, 185 {0xa3, 0, "Maintenance in"}, 186 {0xa3, PDT_MMC, "Send key"}, 187 {0xa4, 0, "Maintenance out"}, 188 {0xa4, PDT_MMC, "Report key"}, 189 {0xa5, 0, "Move medium"}, 190 {0xa5, PDT_MMC, "Play audio(12)"}, 191 {0xa6, 0, "Exchange medium"}, 192 {0xa6, PDT_MMC, "Load/unload medium"}, 193 {0xa7, 0, "Move medium attached"}, 194 {0xa7, PDT_MMC, "Set read ahead"}, 195 {0xa8, 0, "Read(12)"}, /* SBC-3 r31 recommends Read(16) */ 196 {0xa9, 0, "Service action out(12)"}, 197 {0xaa, 0, "Write(12)"}, /* SBC-3 r31 recommends Write(16) */ 198 {0xab, 0, "Service action in(12)"}, 199 {0xac, 0, "erase(12)"}, 200 {0xac, PDT_MMC, "Get performance"}, 201 {0xad, PDT_MMC, "Read DVD/BD structure"}, 202 {0xae, 0, "Write and verify(12)"}, 203 /* SBC-3 r31 recommends Write and verify(16) */ 204 {0xaf, 0, "Verify(12)"}, /* SBC-3 r31 recommends Verify(16) */ 205 {0xb0, 0, "Search data high(12)"}, 206 {0xb1, 0, "Search data equal(12)"}, 207 {0xb1, PDT_MCHANGER, "Open/close import/export element"}, 208 {0xb2, 0, "Search data low(12)"}, 209 {0xb3, 0, "Set limits(12)"}, 210 {0xb4, 0, "Read element status attached"}, 211 {0xb5, 0, "Security protocol out"}, 212 {0xb5, PDT_MCHANGER, "Request volume element address"}, 213 {0xb6, 0, "Send volume tag"}, 214 {0xb6, PDT_MMC, "Set streaming"}, 215 {0xb7, 0, "Read defect data(12)"}, 216 {0xb8, 0, "Read element status"}, 217 {0xb9, 0, "Read CD msf"}, 218 {0xba, 0, "Redundancy group in"}, 219 {0xba, PDT_MMC, "Scan"}, 220 {0xbb, 0, "Redundancy group out"}, 221 {0xbb, PDT_MMC, "Set CD speed"}, 222 {0xbc, 0, "Spare in"}, 223 {0xbd, 0, "Spare out"}, 224 {0xbd, PDT_MMC, "Mechanism status"}, 225 {0xbe, 0, "Volume set in"}, 226 {0xbe, PDT_MMC, "Read CD"}, 227 {0xbf, 0, "Volume set out"}, 228 {0xbf, PDT_MMC, "Send DVD/BD structure"}, 229 {0xffff, 0, NULL}, 230}; 231 232/* Read buffer(10) [0x3c] and Read buffer(16) [0x9b] service actions (sa), 233 * need prefix */ 234struct sg_lib_value_name_t sg_lib_read_buff_arr[] = { 235 {0x0, 0, "combined header and data [or multiple modes]"}, 236 {0x2, 0, "data"}, 237 {0x3, 0, "descriptor"}, 238 {0xa, 0, "read data from echo buffer"}, 239 {0xb, 0, "echo buffer descriptor"}, 240 {0x1a, 0, "enable expander comms protocol and echo buffer"}, 241 {0x1c, 0, "error history"}, 242 {0xffff, 0, NULL}, 243}; 244 245/* Write buffer [0x3b] service actions, need prefix */ 246struct sg_lib_value_name_t sg_lib_write_buff_arr[] = { 247 {0x0, 0, "combined header and data [or multiple modes]"}, 248 {0x2, 0, "data"}, 249 {0x4, 0, "download microcode and activate"}, 250 {0x5, 0, "download microcode, save, and activate"}, 251 {0x6, 0, "download microcode with offsets and activate"}, 252 {0x7, 0, "download microcode with offsets, save, and activate"}, 253 {0xa, 0, "write data to echo buffer"}, 254 {0xd, 0, "download microcode with offsets, select activation events, " 255 "save and defer activate"}, 256 {0xe, 0, "download microcode with offsets, save and defer activate"}, 257 {0xf, 0, "activate deferred microcode"}, 258 {0x1a, 0, "enable expander comms protocol and echo buffer"}, 259 {0x1b, 0, "disable expander comms protocol"}, 260 {0x1c, 0, "download application client error history"}, 261 {0xffff, 0, NULL}, 262}; 263 264/* Read position (SSC) [0x34] service actions, need prefix */ 265struct sg_lib_value_name_t sg_lib_read_pos_arr[] = { 266 {0x0, PDT_TAPE, "short form - block id"}, 267 {0x1, PDT_TAPE, "short form - vendor specific"}, 268 {0x6, PDT_TAPE, "long form"}, 269 {0x8, PDT_TAPE, "extended form"}, 270 {0xffff, 0, NULL}, 271}; 272 273/* Maintenance in [0xa3] service actions */ 274struct sg_lib_value_name_t sg_lib_maint_in_arr[] = { 275 {0x0, PDT_SAC, "Report assigned/unassigned p_extent"}, 276 {0x1, PDT_SAC, "Report component device"}, 277 {0x2, PDT_SAC, "Report component device attachments"}, 278 {0x3, PDT_SAC, "Report peripheral device"}, 279 {0x4, PDT_SAC, "Report peripheral device associations"}, 280 {0x5, 0, "Report identifying information"}, 281 /* was "Report device identifier" prior to spc4r07 */ 282 {0x6, PDT_SAC, "Report states"}, 283 {0x7, PDT_SAC, "Report device identification"}, 284 {0x8, PDT_SAC, "Report unconfigured capacity"}, 285 {0x9, PDT_SAC, "Report supported configuration method"}, 286 {0xa, 0, "Report target port groups"}, 287 {0xb, 0, "Report aliases"}, 288 {0xc, 0, "Report supported operation codes"}, 289 {0xd, 0, "Report supported task management functions"}, 290 {0xe, 0, "Report priority"}, 291 {0xf, 0, "Report timestamp"}, 292 {0x10, 0, "Management protocol in"}, 293 {0x1d, PDT_DISK, "Report provisioning initialization pattern"}, 294 /* added in sbc4r07, shares sa 0x1d with ssc5r01 (tape) */ 295 {0x1d, PDT_TAPE, "Receive recommended access order"}, 296 {0x1e, PDT_TAPE, "Read dynamic runtime attribute"}, 297 {0x1e, PDT_ADC, "Report automation device attributes"}, 298 {0x1f, 0, "Maintenance in vendor specific"}, 299 {0xffff, 0, NULL}, 300}; 301 302/* Maintenance out [0xa4] service actions */ 303struct sg_lib_value_name_t sg_lib_maint_out_arr[] = { 304 {0x0, PDT_SAC, "Add peripheral device / component device"}, 305 {0x1, PDT_SAC, "Attach to component device"}, 306 {0x2, PDT_SAC, "Exchange p_extent"}, 307 {0x3, PDT_SAC, "Exchange peripheral device / component device"}, 308 {0x4, PDT_SAC, "Instruct component device"}, 309 {0x5, PDT_SAC, "Remove peripheral device / component device"}, 310 {0x6, 0, "Set identifying information"}, 311 /* was "Set device identifier" prior to spc4r07 */ 312 {0x7, PDT_SAC, "Break peripheral device / component device"}, 313 {0xa, 0, "Set target port groups"}, 314 {0xb, 0, "Change aliases"}, 315 {0xc, 0, "Remove I_T nexus"}, 316 {0xe, 0, "Set priority"}, 317 {0xf, 0, "Set timestamp"}, 318 {0x10, 0, "Management protocol out"}, 319 {0x1d, PDT_TAPE, "Generate recommended access order"}, 320 {0x1e, PDT_TAPE, "write dynamic runtime attribute"}, 321 {0x1e, PDT_ADC, "Set automation device attributes"}, 322 {0x1f, 0, "Maintenance out vendor specific"}, 323 {0xffff, 0, NULL}, 324}; 325 326/* Sanitize [0x48] service actions, need prefix */ 327struct sg_lib_value_name_t sg_lib_sanitize_sa_arr[] = { 328 {0x1, 0, "overwrite"}, 329 {0x2, 0, "block erase"}, 330 {0x3, 0, "cryptographic erase"}, 331 {0x1f, 0, "exit failure mode"}, 332 {0xffff, 0, NULL}, 333}; 334 335/* Service action in(12) [0xab] service actions */ 336struct sg_lib_value_name_t sg_lib_serv_in12_arr[] = { 337 {0x1, 0, "Read media serial number"}, 338 {0xffff, 0, NULL}, 339}; 340 341/* Service action out(12) [0xa9] service actions */ 342struct sg_lib_value_name_t sg_lib_serv_out12_arr[] = { 343 {0xff, 0, "Impossible command name"}, 344 {0xffff, 0, NULL}, 345}; 346 347/* Service action in(16) [0x9e] service actions */ 348struct sg_lib_value_name_t sg_lib_serv_in16_arr[] = { 349 {0xf, 0, "Receive binding report"}, /* added spc5r11 */ 350 {0x10, 0, "Read capacity(16)"}, 351 {0x11, 0, "Read long(16)"}, /* obsolete in SBC-4 r7 */ 352 {0x12, 0, "Get LBA status(16)"}, /* 32 byte variant added in sbc4r14 */ 353 {0x13, 0, "Report referrals"}, 354 {0x14, 0, "Stream control"}, 355 {0x15, 0, "Background control"}, 356 {0x16, 0, "Get stream status"}, 357 {0x17, 0, "Get physical element status"}, /* added sbc4r13 */ 358 {0x18, 0, "Remove element and truncate"}, /* added sbc4r13 */ 359 {0xffff, 0, NULL}, 360}; 361 362/* Service action out(16) [0x9f] service actions */ 363struct sg_lib_value_name_t sg_lib_serv_out16_arr[] = { 364 {0x0b, 0, "Test bind"}, /* added spc5r13 */ 365 {0x0c, 0, "Prepare bind report"}, /* added spc5r11 */ 366 {0x0d, 0, "Set affiliation"}, 367 {0x0e, 0, "Bind"}, 368 {0x0f, 0, "Unbind"}, 369 {0x11, 0, "Write long(16)"}, 370 {0x12, 0, "Write scattered(16)"}, /* added sbc4r11 */ 371 {0x14, PDT_ZBC, "Reset write pointer"}, 372 {0x1f, PDT_ADC, "Notify data transfer device(16)"}, 373 {0xffff, 0, NULL}, 374}; 375 376/* Service action bidirectional [0x9d] service actions */ 377struct sg_lib_value_name_t sg_lib_serv_bidi_arr[] = { 378 {0xffff, 0, NULL}, 379}; 380 381/* Persistent reserve in [0x5e] service actions, need prefix */ 382struct sg_lib_value_name_t sg_lib_pr_in_arr[] = { 383 {0x0, 0, "read keys"}, 384 {0x1, 0, "read reservation"}, 385 {0x2, 0, "report capabilities"}, 386 {0x3, 0, "read full status"}, 387 {0xffff, 0, NULL}, 388}; 389 390/* Persistent reserve out [0x5f] service actions, need prefix */ 391struct sg_lib_value_name_t sg_lib_pr_out_arr[] = { 392 {0x0, 0, "register"}, 393 {0x1, 0, "reserve"}, 394 {0x2, 0, "release"}, 395 {0x3, 0, "clear"}, 396 {0x4, 0, "preempt"}, 397 {0x5, 0, "preempt and abort"}, 398 {0x6, 0, "register and ignore existing key"}, 399 {0x7, 0, "register and move"}, 400 {0x8, 0, "replace lost reservation"}, 401 {0xffff, 0, NULL}, 402}; 403 404/* Third party copy in [0x83] service actions 405 * Opcode 'Receive copy results' was renamed 'Third party copy in' in spc4r34 406 * LID1 is an abbreviation of List Identifier length of 1 byte */ 407struct sg_lib_value_name_t sg_lib_xcopy_sa_arr[] = { 408 {0x0, 0, "Extended copy(LID1)"}, 409 {0x1, 0, "Extended copy(LID4)"}, 410 {0x10, 0, "Populate token"}, 411 {0x11, 0, "Write using token"}, 412 {0x1c, 0, "Copy operation abort"}, 413 {0xffff, 0, NULL}, 414}; 415 416/* Third party copy out [0x84] service actions 417 * Opcode 'Extended copy' was renamed 'Third party copy out' in spc4r34 418 * LID4 is an abbreviation of List Identifier length of 4 bytes */ 419struct sg_lib_value_name_t sg_lib_rec_copy_sa_arr[] = { 420 {0x0, 0, "Receive copy status(LID1)"}, 421 {0x1, 0, "Receive copy data(LID1)"}, 422 {0x3, 0, "Receive copy operating parameters"}, 423 {0x4, 0, "Receive copy failure details(LID1)"}, 424 {0x5, 0, "Receive copy status(LID4)"}, 425 {0x6, 0, "Receive copy data(LID4)"}, 426 {0x7, 0, "Receive ROD token information"}, 427 {0x8, 0, "Report all ROD tokens"}, 428 {0xffff, 0, NULL}, 429}; 430 431/* Variable length cdb [0x7f] service actions (more than 16 bytes long) */ 432struct sg_lib_value_name_t sg_lib_variable_length_arr[] = { 433 {0x1, 0, "Rebuild(32)"}, 434 {0x2, 0, "Regenerate(32)"}, 435 {0x3, 0, "Xdread(32)"}, /* obsolete in SBC-3 r31 */ 436 {0x4, 0, "Xdwrite(32)"}, /* obsolete in SBC-3 r31 */ 437 {0x5, 0, "Xdwrite extended(32)"}, /* obsolete in SBC-4 r15 */ 438 {0x6, 0, "Xpwrite(32)"}, /* obsolete in SBC-4 r15 */ 439 {0x7, 0, "Xdwriteread(32)"}, /* obsolete in SBC-4 r15 */ 440 {0x8, 0, "Xdwrite extended(64)"}, /* obsolete in SBC-4 r15 */ 441 {0x9, 0, "Read(32)"}, 442 {0xa, 0, "Verify(32)"}, 443 {0xb, 0, "Write(32)"}, 444 {0xc, 0, "Write and verify(32)"}, 445 {0xd, 0, "Write same(32)"}, 446 {0xe, 0, "Orwrite(32)"}, /* added sbc3r25 */ 447 {0xf, 0, "Atomic write(32)"}, /* added sbc4r02 */ 448 {0x10, 0, "Write stream(32)"}, /* added sbc4r07 */ 449 {0x11, 0, "Write scattered(32)"}, /* added sbc4r11 */ 450 {0x12, 0, "Get LBA status(32)"}, /* added sbc4r14 */ 451 {0x1800, 0, "Receive credential"}, 452 {0x1ff0, 0, "ATA pass-through(32)"},/* added sat4r05 */ 453 {0x8801, 0, "Format OSD (osd)"}, 454 {0x8802, 0, "Create (osd)"}, 455 {0x8803, 0, "List (osd)"}, 456 {0x8805, 0, "Read (osd)"}, 457 {0x8806, 0, "Write (osd)"}, 458 {0x8807, 0, "Append (osd)"}, 459 {0x8808, 0, "Flush (osd)"}, 460 {0x880a, 0, "Remove (osd)"}, 461 {0x880b, 0, "Create partition (osd)"}, 462 {0x880c, 0, "Remove partition (osd)"}, 463 {0x880e, 0, "Get attributes (osd)"}, 464 {0x880f, 0, "Set attributes (osd)"}, 465 {0x8812, 0, "Create and write (osd)"}, 466 {0x8815, 0, "Create collection (osd)"}, 467 {0x8816, 0, "Remove collection (osd)"}, 468 {0x8817, 0, "List collection (osd)"}, 469 {0x8818, 0, "Set key (osd)"}, 470 {0x8819, 0, "Set master key (osd)"}, 471 {0x881a, 0, "Flush collection (osd)"}, 472 {0x881b, 0, "Flush partition (osd)"}, 473 {0x881c, 0, "Flush OSD (osd)"}, 474 {0x8880, 0, "Object structure check (osd-2)"}, 475 {0x8881, 0, "Format OSD (osd-2)"}, 476 {0x8882, 0, "Create (osd-2)"}, 477 {0x8883, 0, "List (osd-2)"}, 478 {0x8884, 0, "Punch (osd-2)"}, 479 {0x8885, 0, "Read (osd-2)"}, 480 {0x8886, 0, "Write (osd-2)"}, 481 {0x8887, 0, "Append (osd-2)"}, 482 {0x8888, 0, "Flush (osd-2)"}, 483 {0x8889, 0, "Clear (osd-2)"}, 484 {0x888a, 0, "Remove (osd-2)"}, 485 {0x888b, 0, "Create partition (osd-2)"}, 486 {0x888c, 0, "Remove partition (osd-2)"}, 487 {0x888e, 0, "Get attributes (osd-2)"}, 488 {0x888f, 0, "Set attributes (osd-2)"}, 489 {0x8892, 0, "Create and write (osd-2)"}, 490 {0x8895, 0, "Create collection (osd-2)"}, 491 {0x8896, 0, "Remove collection (osd-2)"}, 492 {0x8897, 0, "List collection (osd-2)"}, 493 {0x8898, 0, "Set key (osd-2)"}, 494 {0x8899, 0, "Set master key (osd-2)"}, 495 {0x889a, 0, "Flush collection (osd-2)"}, 496 {0x889b, 0, "Flush partition (osd-2)"}, 497 {0x889c, 0, "Flush OSD (osd-2)"}, 498 {0x88a0, 0, "Query (osd-2)"}, 499 {0x88a1, 0, "Remove member objects (osd-2)"}, 500 {0x88a2, 0, "Get member attributes (osd-2)"}, 501 {0x88a3, 0, "Set member attributes (osd-2)"}, 502 {0x88b1, 0, "Read map (osd-2)"}, 503 {0x8f7c, 0, "Perform SCSI command (osd-2)"}, 504 {0x8f7d, 0, "Perform task management function (osd-2)"}, 505 {0x8f7e, 0, "Perform SCSI command (osd)"}, 506 {0x8f7f, 0, "Perform task management function (osd)"}, 507 {0xffff, 0, NULL}, 508}; 509 510/* Zoning out [0x94] service actions */ 511struct sg_lib_value_name_t sg_lib_zoning_out_arr[] = { 512 {0x1, PDT_ZBC, "Close zone"}, 513 {0x2, PDT_ZBC, "Finish zone"}, 514 {0x3, PDT_ZBC, "Open zone"}, 515 {0x4, PDT_ZBC, "Reset write pointer"}, 516 {0xffff, 0, NULL}, 517}; 518 519/* Zoning in [0x95] service actions */ 520struct sg_lib_value_name_t sg_lib_zoning_in_arr[] = { 521 {0x0, PDT_ZBC, "Report zones"}, 522 {0xffff, 0, NULL}, 523}; 524 525/* Read attribute [0x8c] service actions */ 526struct sg_lib_value_name_t sg_lib_read_attr_arr[] = { 527 {0x0, 0, "attribute values"}, 528 {0x1, 0, "attribute list"}, 529 {0x2, 0, "logical volume list"}, 530 {0x3, 0, "partition list"}, 531 {0x5, 0, "supported attributes"}, 532 {0xffff, 0, NULL}, 533}; 534 535#else /* SG_SCSI_STRINGS */ 536 537struct sg_lib_value_name_t sg_lib_normal_opcodes[] = { 538 {0xffff, 0, NULL}, 539}; 540 541struct sg_lib_value_name_t sg_lib_read_buff_arr[] = { /* opcode 0x3c */ 542 {0xffff, 0, NULL}, 543}; 544 545struct sg_lib_value_name_t sg_lib_write_buff_arr[] = { /* opcode 0x3b */ 546 {0xffff, 0, NULL}, 547}; 548 549struct sg_lib_value_name_t sg_lib_read_pos_arr[] = { /* opcode 0x34 */ 550 {0xffff, 0, NULL}, 551}; 552 553struct sg_lib_value_name_t sg_lib_maint_in_arr[] = { /* opcode 0xa3 */ 554 {0xffff, 0, NULL}, 555}; 556 557struct sg_lib_value_name_t sg_lib_maint_out_arr[] = { /* opcode 0xa4 */ 558 {0xffff, 0, NULL}, 559}; 560 561struct sg_lib_value_name_t sg_lib_sanitize_sa_arr[] = { /* opcode 0x94 */ 562 {0xffff, 0, NULL}, 563}; 564 565struct sg_lib_value_name_t sg_lib_serv_in12_arr[] = { /* opcode 0xab */ 566 {0xffff, 0, NULL}, 567}; 568 569struct sg_lib_value_name_t sg_lib_serv_out12_arr[] = { /* opcode 0xa9 */ 570 {0xffff, 0, NULL}, 571}; 572 573struct sg_lib_value_name_t sg_lib_serv_in16_arr[] = { /* opcode 0x9e */ 574 {0xffff, 0, NULL}, 575}; 576 577struct sg_lib_value_name_t sg_lib_serv_out16_arr[] = { /* opcode 0x9f */ 578 {0xffff, 0, NULL}, 579}; 580 581struct sg_lib_value_name_t sg_lib_serv_bidi_arr[] = { /* opcode 0x9d */ 582 {0xffff, 0, NULL}, 583}; 584 585struct sg_lib_value_name_t sg_lib_pr_in_arr[] = { /* opcode 0x5e */ 586 {0xffff, 0, NULL}, 587}; 588 589struct sg_lib_value_name_t sg_lib_pr_out_arr[] = { /* opcode 0x5f */ 590 {0xffff, 0, NULL}, 591}; 592 593struct sg_lib_value_name_t sg_lib_xcopy_sa_arr[] = { /* opcode 0x83 */ 594 {0xffff, 0, NULL}, 595}; 596 597struct sg_lib_value_name_t sg_lib_rec_copy_sa_arr[] = { /* opcode 0x84 */ 598 {0xffff, 0, NULL}, 599}; 600 601struct sg_lib_value_name_t sg_lib_variable_length_arr[] = { 602 {0xffff, 0, NULL}, 603}; 604 605struct sg_lib_value_name_t sg_lib_zoning_out_arr[] = { 606 {0xffff, 0, NULL}, 607}; 608 609struct sg_lib_value_name_t sg_lib_zoning_in_arr[] = { 610 {0xffff, 0, NULL}, 611}; 612 613struct sg_lib_value_name_t sg_lib_read_attr_arr[] = { 614 {0xffff, 0, NULL}, 615}; 616 617#endif /* SG_SCSI_STRINGS */ 618 619/* A conveniently formatted list of SCSI ASC/ASCQ codes and their 620 * corresponding text can be found at: www.t10.org/lists/asc-num.txt 621 * The following should match asc-num.txt dated 20150423 */ 622 623#ifdef SG_SCSI_STRINGS 624struct sg_lib_asc_ascq_range_t sg_lib_asc_ascq_range[] = 625{ 626 {0x40,0x01,0x7f,"Ram failure [0x%x]"}, 627 {0x40,0x80,0xff,"Diagnostic failure on component [0x%x]"}, 628 {0x41,0x01,0xff,"Data path failure [0x%x]"}, 629 {0x42,0x01,0xff,"Power-on or self-test failure [0x%x]"}, 630 {0x4d,0x00,0xff,"Tagged overlapped commands [0x%x]"}, 631 {0x70,0x00,0xff,"Decompression exception short algorithm id of 0x%x"}, 632 {0, 0, 0, NULL} 633}; 634 635struct sg_lib_asc_ascq_t sg_lib_asc_ascq[] = 636{ 637 {0x00,0x00,"No additional sense information"}, 638 {0x00,0x01,"Filemark detected"}, 639 {0x00,0x02,"End-of-partition/medium detected"}, 640 {0x00,0x03,"Setmark detected"}, 641 {0x00,0x04,"Beginning-of-partition/medium detected"}, 642 {0x00,0x05,"End-of-data detected"}, 643 {0x00,0x06,"I/O process terminated"}, 644 {0x00,0x07,"Programmable early warning detected"}, 645 {0x00,0x11,"Audio play operation in progress"}, 646 {0x00,0x12,"Audio play operation paused"}, 647 {0x00,0x13,"Audio play operation successfully completed"}, 648 {0x00,0x14,"Audio play operation stopped due to error"}, 649 {0x00,0x15,"No current audio status to return"}, 650 {0x00,0x16,"operation in progress"}, 651 {0x00,0x17,"Cleaning requested"}, 652 {0x00,0x18,"Erase operation in progress"}, 653 {0x00,0x19,"Locate operation in progress"}, 654 {0x00,0x1a,"Rewind operation in progress"}, 655 {0x00,0x1b,"Set capacity operation in progress"}, 656 {0x00,0x1c,"Verify operation in progress"}, 657 {0x00,0x1d,"ATA pass through information available"}, 658 {0x00,0x1e,"Conflicting SA creation request"}, 659 {0x00,0x1f,"Logical unit transitioning to another power condition"}, 660 {0x00,0x20,"Extended copy information available"}, 661 {0x00,0x21,"Atomic command aborted due to ACA"}, 662 {0x00,0x22,"Deferred microcode is pending"}, 663 {0x01,0x00,"No index/sector signal"}, 664 {0x02,0x00,"No seek complete"}, 665 {0x03,0x00,"Peripheral device write fault"}, 666 {0x03,0x01,"No write current"}, 667 {0x03,0x02,"Excessive write errors"}, 668 {0x04,0x00,"Logical unit not ready, cause not reportable"}, 669 {0x04,0x01,"Logical unit is in process of becoming ready"}, 670 {0x04,0x02,"Logical unit not ready, " 671 "initializing command required"}, 672 {0x04,0x03,"Logical unit not ready, " 673 "manual intervention required"}, 674 {0x04,0x04,"Logical unit not ready, format in progress"}, 675 {0x04,0x05,"Logical unit not ready, rebuild in progress"}, 676 {0x04,0x06,"Logical unit not ready, recalculation in progress"}, 677 {0x04,0x07,"Logical unit not ready, operation in progress"}, 678 {0x04,0x08,"Logical unit not ready, long write in progress"}, 679 {0x04,0x09,"Logical unit not ready, self-test in progress"}, 680 {0x04,0x0a,"Logical unit " 681 "not accessible, asymmetric access state transition"}, 682 {0x04,0x0b,"Logical unit " 683 "not accessible, target port in standby state"}, 684 {0x04,0x0c,"Logical unit " 685 "not accessible, target port in unavailable state"}, 686 {0x04,0x0d,"Logical unit not ready, structure check required"}, 687 {0x04,0x0e,"Logical unit not ready, security session in progress"}, 688 {0x04,0x10,"Logical unit not ready, " 689 "auxiliary memory not accessible"}, 690 {0x04,0x11,"Logical unit not ready, " 691 "notify (enable spinup) required"}, 692 {0x04,0x12,"Logical unit not ready, offline"}, 693 {0x04,0x13,"Logical unit not ready, SA creation in progress"}, 694 {0x04,0x14,"Logical unit not ready, space allocation in progress"}, 695 {0x04,0x15,"Logical unit not ready, robotics disabled"}, 696 {0x04,0x16,"Logical unit not ready, configuration required"}, 697 {0x04,0x17,"Logical unit not ready, calibration required"}, 698 {0x04,0x18,"Logical unit not ready, a door is open"}, 699 {0x04,0x19,"Logical unit not ready, operating in sequential mode"}, 700 {0x04,0x1a,"Logical unit not ready, start stop unit command in progress"}, 701 {0x04,0x1b,"Logical unit not ready, sanitize in progress"}, 702 {0x04,0x1c,"Logical unit not ready, additional power use not yet " 703 "granted"}, 704 {0x04,0x1d,"Logical unit not ready, configuration in progress"}, 705 {0x04,0x1e,"Logical unit not ready, microcode activation required"}, 706 {0x04,0x1f,"Logical unit not ready, microcode download required"}, 707 {0x04,0x20,"Logical unit not ready, logical unit reset required"}, 708 {0x04,0x21,"Logical unit not ready, hard reset required"}, 709 {0x04,0x22,"Logical unit not ready, power cycle required"}, 710 {0x04,0x23,"Logical unit not ready, affiliation required"}, 711 {0x05,0x00,"Logical unit does not respond to selection"}, 712 {0x06,0x00,"No reference position found"}, 713 {0x07,0x00,"Multiple peripheral devices selected"}, 714 {0x08,0x00,"Logical unit communication failure"}, 715 {0x08,0x01,"Logical unit communication time-out"}, 716 {0x08,0x02,"Logical unit communication parity error"}, 717 {0x08,0x03,"Logical unit communication CRC error (Ultra-DMA/32)"}, 718 {0x08,0x04,"Unreachable copy target"}, 719 {0x09,0x00,"Track following error"}, 720 {0x09,0x01,"Tracking servo failure"}, 721 {0x09,0x02,"Focus servo failure"}, 722 {0x09,0x03,"Spindle servo failure"}, 723 {0x09,0x04,"Head select fault"}, 724 {0x09,0x05,"Vibration induced tracking error"}, 725 {0x0A,0x00,"Error log overflow"}, 726 {0x0B,0x00,"Warning"}, 727 {0x0B,0x01,"Warning - specified temperature exceeded"}, 728 {0x0B,0x02,"Warning - enclosure degraded"}, 729 {0x0B,0x03,"Warning - background self-test failed"}, 730 {0x0B,0x04,"Warning - background pre-scan detected medium error"}, 731 {0x0B,0x05,"Warning - background medium scan detected medium error"}, 732 {0x0B,0x06,"Warning - non-volatile cache now volatile"}, 733 {0x0B,0x07,"Warning - degraded power to non-volatile cache"}, 734 {0x0B,0x08,"Warning - power loss expected"}, 735 {0x0B,0x09,"Warning - device statistics notification active"}, 736 {0x0B,0x0A,"Warning - high critical temperature limit exceeded"}, 737 {0x0B,0x0B,"Warning - low critical temperature limit exceeded"}, 738 {0x0B,0x0C,"Warning - high operating temperature limit exceeded"}, 739 {0x0B,0x0D,"Warning - low operating temperature limit exceeded"}, 740 {0x0B,0x0E,"Warning - high critical humidity limit exceeded"}, 741 {0x0B,0x0F,"Warning - low critical humidity limit exceeded"}, 742 {0x0B,0x10,"Warning - high operating humidity limit exceeded"}, 743 {0x0B,0x11,"Warning - low operating humidity limit exceeded"}, 744 {0x0B,0x12,"Warning - microcode security at risk"}, 745 {0x0B,0x13,"Warning - microcode digital signature validation failure"}, 746 {0x0C,0x00,"Write error"}, 747 {0x0C,0x01,"Write error - recovered with auto reallocation"}, 748 {0x0C,0x02,"Write error - auto reallocation failed"}, 749 {0x0C,0x03,"Write error - recommend reassignment"}, 750 {0x0C,0x04,"Compression check miscompare error"}, 751 {0x0C,0x05,"Data expansion occurred during compression"}, 752 {0x0C,0x06,"Block not compressible"}, 753 {0x0C,0x07,"Write error - recovery needed"}, 754 {0x0C,0x08,"Write error - recovery failed"}, 755 {0x0C,0x09,"Write error - loss of streaming"}, 756 {0x0C,0x0A,"Write error - padding blocks added"}, 757 {0x0C,0x0B,"Auxiliary memory write error"}, 758 {0x0C,0x0C,"Write error - unexpected unsolicited data"}, 759 {0x0C,0x0D,"Write error - not enough unsolicited data"}, 760 {0x0C,0x0E,"Multiple write errors"}, 761 {0x0C,0x0F,"Defects in error window"}, 762 {0x0C,0x10,"Incomplete multiple atomic write operations"}, 763 {0x0C,0x11,"Write error - recovery scan needed"}, 764 {0x0C,0x12,"Write error - insufficient zone resources"}, 765 {0x0D,0x00,"Error detected by third party temporary initiator"}, 766 {0x0D,0x01,"Third party device failure"}, 767 {0x0D,0x02,"Copy target device not reachable"}, 768 {0x0D,0x03,"Incorrect copy target device type"}, 769 {0x0D,0x04,"Copy target device data underrun"}, 770 {0x0D,0x05,"Copy target device data overrun"}, 771 {0x0E,0x00,"Invalid information unit"}, 772 {0x0E,0x01,"Information unit too short"}, 773 {0x0E,0x02,"Information unit too long"}, 774 {0x0E,0x03,"Invalid field in command information unit"}, 775 {0x10,0x00,"Id CRC or ECC error"}, 776 {0x10,0x01,"Logical block guard check failed"}, 777 {0x10,0x02,"Logical block application tag check failed"}, 778 {0x10,0x03,"Logical block reference tag check failed"}, 779 {0x10,0x04,"Logical block protection error on recover buffered data"}, 780 {0x10,0x05,"Logical block protection method error"}, 781 {0x11,0x00,"Unrecovered read error"}, 782 {0x11,0x01,"Read retries exhausted"}, 783 {0x11,0x02,"Error too long to correct"}, 784 {0x11,0x03,"Multiple read errors"}, 785 {0x11,0x04,"Unrecovered read error - auto reallocate failed"}, 786 {0x11,0x05,"L-EC uncorrectable error"}, 787 {0x11,0x06,"CIRC unrecovered error"}, 788 {0x11,0x07,"Data re-synchronization error"}, 789 {0x11,0x08,"Incomplete block read"}, 790 {0x11,0x09,"No gap found"}, 791 {0x11,0x0A,"Miscorrected error"}, 792 {0x11,0x0B,"Unrecovered read error - recommend reassignment"}, 793 {0x11,0x0C,"Unrecovered read error - recommend rewrite the data"}, 794 {0x11,0x0D,"De-compression CRC error"}, 795 {0x11,0x0E,"Cannot decompress using declared algorithm"}, 796 {0x11,0x0F,"Error reading UPC/EAN number"}, 797 {0x11,0x10,"Error reading ISRC number"}, 798 {0x11,0x11,"Read error - loss of streaming"}, 799 {0x11,0x12,"Auxiliary memory read error"}, 800 {0x11,0x13,"Read error - failed retransmission request"}, 801 {0x11,0x14,"Read error - LBA marked bad by application client"}, 802 {0x11,0x15,"Write after sanitize required"}, 803 {0x12,0x00,"Address mark not found for id field"}, 804 {0x13,0x00,"Address mark not found for data field"}, 805 {0x14,0x00,"Recorded entity not found"}, 806 {0x14,0x01,"Record not found"}, 807 {0x14,0x02,"Filemark or setmark not found"}, 808 {0x14,0x03,"End-of-data not found"}, 809 {0x14,0x04,"Block sequence error"}, 810 {0x14,0x05,"Record not found - recommend reassignment"}, 811 {0x14,0x06,"Record not found - data auto-reallocated"}, 812 {0x14,0x07,"Locate operation failure"}, 813 {0x15,0x00,"Random positioning error"}, 814 {0x15,0x01,"Mechanical positioning error"}, 815 {0x15,0x02,"Positioning error detected by read of medium"}, 816 {0x16,0x00,"Data synchronization mark error"}, 817 {0x16,0x01,"Data sync error - data rewritten"}, 818 {0x16,0x02,"Data sync error - recommend rewrite"}, 819 {0x16,0x03,"Data sync error - data auto-reallocated"}, 820 {0x16,0x04,"Data sync error - recommend reassignment"}, 821 {0x17,0x00,"Recovered data with no error correction applied"}, 822 {0x17,0x01,"Recovered data with retries"}, 823 {0x17,0x02,"Recovered data with positive head offset"}, 824 {0x17,0x03,"Recovered data with negative head offset"}, 825 {0x17,0x04,"Recovered data with retries and/or circ applied"}, 826 {0x17,0x05,"Recovered data using previous sector id"}, 827 {0x17,0x06,"Recovered data without ECC - data auto-reallocated"}, 828 {0x17,0x07,"Recovered data without ECC - recommend reassignment"}, 829 {0x17,0x08,"Recovered data without ECC - recommend rewrite"}, 830 {0x17,0x09,"Recovered data without ECC - data rewritten"}, 831 {0x18,0x00,"Recovered data with error correction applied"}, 832 {0x18,0x01,"Recovered data with error corr. & retries applied"}, 833 {0x18,0x02,"Recovered data - data auto-reallocated"}, 834 {0x18,0x03,"Recovered data with CIRC"}, 835 {0x18,0x04,"Recovered data with L-EC"}, 836 {0x18,0x05,"Recovered data - recommend reassignment"}, 837 {0x18,0x06,"Recovered data - recommend rewrite"}, 838 {0x18,0x07,"Recovered data with ECC - data rewritten"}, 839 {0x18,0x08,"Recovered data with linking"}, 840 {0x19,0x00,"Defect list error"}, 841 {0x19,0x01,"Defect list not available"}, 842 {0x19,0x02,"Defect list error in primary list"}, 843 {0x19,0x03,"Defect list error in grown list"}, 844 {0x1A,0x00,"Parameter list length error"}, 845 {0x1B,0x00,"Synchronous data transfer error"}, 846 {0x1C,0x00,"Defect list not found"}, 847 {0x1C,0x01,"Primary defect list not found"}, 848 {0x1C,0x02,"Grown defect list not found"}, 849 {0x1D,0x00,"Miscompare during verify operation"}, 850 {0x1D,0x01,"Miscompare verify of unmapped lba"}, 851 {0x1E,0x00,"Recovered id with ECC correction"}, 852 {0x1F,0x00,"Partial defect list transfer"}, 853 {0x20,0x00,"Invalid command operation code"}, 854 {0x20,0x01,"Access denied - initiator pending-enrolled"}, 855 {0x20,0x02,"Access denied - no access rights"}, 856 {0x20,0x03,"Access denied - invalid mgmt id key"}, 857 {0x20,0x04,"Illegal command while in write capable state"}, 858 {0x20,0x05,"Write type operation while in read capable state (obs)"}, 859 {0x20,0x06,"Illegal command while in explicit address mode"}, 860 {0x20,0x07,"Illegal command while in implicit address mode"}, 861 {0x20,0x08,"Access denied - enrollment conflict"}, 862 {0x20,0x09,"Access denied - invalid LU identifier"}, 863 {0x20,0x0A,"Access denied - invalid proxy token"}, 864 {0x20,0x0B,"Access denied - ACL LUN conflict"}, 865 {0x20,0x0C,"Illegal command when not in append-only mode"}, 866 {0x20,0x0D,"Not an administrative logical unit"}, 867 {0x20,0x0E,"Not a subsidiary logical unit"}, 868 {0x20,0x0F,"Not a conglomerate logical unit"}, 869 {0x21,0x00,"Logical block address out of range"}, 870 {0x21,0x01,"Invalid element address"}, 871 {0x21,0x02,"Invalid address for write"}, 872 {0x21,0x03,"Invalid write crossing layer jump"}, 873 {0x21,0x04,"Unaligned write command"}, 874 {0x21,0x05,"Write boundary violation"}, 875 {0x21,0x06,"Attempt to read invalid data"}, 876 {0x21,0x07,"Read boundary violation"}, 877 {0x21,0x08,"Misaligned write command"}, 878 {0x22,0x00,"Illegal function (use 20 00, 24 00, or 26 00)"}, 879 {0x23,0x00,"Invalid token operation, cause not reportable"}, 880 {0x23,0x01,"Invalid token operation, unsupported token type"}, 881 {0x23,0x02,"Invalid token operation, remote token usage not supported"}, 882 {0x23,0x03,"invalid token operation, remote rod token creation not " 883 "supported"}, 884 {0x23,0x04,"Invalid token operation, token unknown"}, 885 {0x23,0x05,"Invalid token operation, token corrupt"}, 886 {0x23,0x06,"Invalid token operation, token revoked"}, 887 {0x23,0x07,"Invalid token operation, token expired"}, 888 {0x23,0x08,"Invalid token operation, token cancelled"}, 889 {0x23,0x09,"Invalid token operation, token deleted"}, 890 {0x23,0x0a,"Invalid token operation, invalid token length"}, 891 {0x24,0x00,"Invalid field in cdb"}, 892 {0x24,0x01,"CDB decryption error"}, 893 {0x24,0x02,"Invalid cdb field while in explicit block model (obs)"}, 894 {0x24,0x03,"Invalid cdb field while in implicit block model (obs)"}, 895 {0x24,0x04,"Security audit value frozen"}, 896 {0x24,0x05,"Security working key frozen"}, 897 {0x24,0x06,"Nonce not unique"}, 898 {0x24,0x07,"Nonce timestamp out of range"}, 899 {0x24,0x08,"Invalid xcdb"}, 900 {0x24,0x09,"Invalid fast format"}, 901 {0x25,0x00,"Logical unit not supported"}, 902 {0x26,0x00,"Invalid field in parameter list"}, 903 {0x26,0x01,"Parameter not supported"}, 904 {0x26,0x02,"Parameter value invalid"}, 905 {0x26,0x03,"Threshold parameters not supported"}, 906 {0x26,0x04,"Invalid release of persistent reservation"}, 907 {0x26,0x05,"Data decryption error"}, 908 {0x26,0x06,"Too many target descriptors"}, 909 {0x26,0x07,"Unsupported target descriptor type code"}, 910 {0x26,0x08,"Too many segment descriptors"}, 911 {0x26,0x09,"Unsupported segment descriptor type code"}, 912 {0x26,0x0A,"Unexpected inexact segment"}, 913 {0x26,0x0B,"Inline data length exceeded"}, 914 {0x26,0x0C,"Invalid operation for copy source or destination"}, 915 {0x26,0x0D,"Copy segment granularity violation"}, 916 {0x26,0x0E,"Invalid parameter while port is enabled"}, 917 {0x26,0x0F,"Invalid data-out buffer integrity check value"}, 918 {0x26,0x10,"Data decryption key fail limit reached"}, 919 {0x26,0x11,"Incomplete key-associated data set"}, 920 {0x26,0x12,"Vendor specific key reference not found"}, 921 {0x26,0x13,"Application tag mode page is invalid"}, 922 {0x26,0x14,"Tape stream mirroring prevented"}, 923 {0x26,0x15,"Copy source or copy destination not authorized"}, 924 {0x27,0x00,"Write protected"}, 925 {0x27,0x01,"Hardware write protected"}, 926 {0x27,0x02,"Logical unit software write protected"}, 927 {0x27,0x03,"Associated write protect"}, 928 {0x27,0x04,"Persistent write protect"}, 929 {0x27,0x05,"Permanent write protect"}, 930 {0x27,0x06,"Conditional write protect"}, 931 {0x27,0x07,"Space allocation failed write protect"}, 932 {0x27,0x08,"Zone is read only"}, 933 {0x28,0x00,"Not ready to ready change, medium may have changed"}, 934 {0x28,0x01,"Import or export element accessed"}, 935 {0x28,0x02,"Format-layer may have changed"}, 936 {0x28,0x03,"Import/export element accessed, medium changed"}, 937 {0x29,0x00,"Power on, reset, or bus device reset occurred"}, 938 {0x29,0x01,"Power on occurred"}, 939 {0x29,0x02,"SCSI bus reset occurred"}, 940 {0x29,0x03,"Bus device reset function occurred"}, 941 {0x29,0x04,"Device internal reset"}, 942 {0x29,0x05,"Transceiver mode changed to single-ended"}, 943 {0x29,0x06,"Transceiver mode changed to lvd"}, 944 {0x29,0x07,"I_T nexus loss occurred"}, 945 {0x2A,0x00,"Parameters changed"}, 946 {0x2A,0x01,"Mode parameters changed"}, 947 {0x2A,0x02,"Log parameters changed"}, 948 {0x2A,0x03,"Reservations preempted"}, 949 {0x2A,0x04,"Reservations released"}, 950 {0x2A,0x05,"Registrations preempted"}, 951 {0x2A,0x06,"Asymmetric access state changed"}, 952 {0x2A,0x07,"Implicit asymmetric access state transition failed"}, 953 {0x2A,0x08,"Priority changed"}, 954 {0x2A,0x09,"Capacity data has changed"}, 955 {0x2A,0x0c, "Error recovery attributes have changed"}, 956 {0x2A,0x0d, "Data encryption capabilities changed"}, 957 {0x2A,0x10,"Timestamp changed"}, 958 {0x2A,0x11,"Data encryption parameters changed by another i_t nexus"}, 959 {0x2A,0x12,"Data encryption parameters changed by vendor specific event"}, 960 {0x2A,0x13,"Data encryption key instance counter has changed"}, 961 {0x2A,0x0a,"Error history i_t nexus cleared"}, 962 {0x2A,0x0b,"Error history snapshot released"}, 963 {0x2A,0x14,"SA creation capabilities data has changed"}, 964 {0x2A,0x15,"Medium removal prevention preempted"}, 965 {0x2A,0x16,"Zone reset write pointer recommended"}, 966 {0x2B,0x00,"Copy cannot execute since host cannot disconnect"}, 967 {0x2C,0x00,"Command sequence error"}, 968 {0x2C,0x01,"Too many windows specified"}, 969 {0x2C,0x02,"Invalid combination of windows specified"}, 970 {0x2C,0x03,"Current program area is not empty"}, 971 {0x2C,0x04,"Current program area is empty"}, 972 {0x2C,0x05,"Illegal power condition request"}, 973 {0x2C,0x06,"Persistent prevent conflict"}, 974 {0x2C,0x07,"Previous busy status"}, 975 {0x2C,0x08,"Previous task set full status"}, 976 {0x2C,0x09,"Previous reservation conflict status"}, 977 {0x2C,0x0A,"Partition or collection contains user objects"}, 978 {0x2C,0x0B,"Not reserved"}, 979 {0x2C,0x0C,"ORWRITE generation does not match"}, 980 {0x2C,0x0D,"Reset write pointer not allowed"}, 981 {0x2C,0x0E,"Zone is offline"}, 982 {0x2C,0x0F,"Stream not open"}, 983 {0x2C,0x10,"Unwritten data in zone"}, 984 {0x2C,0x11,"Descriptor format sense data required"}, 985 {0x2D,0x00,"Overwrite error on update in place"}, 986 {0x2E,0x00,"Insufficient time for operation"}, 987 {0x2E,0x01,"Command timeout before processing"}, 988 {0x2E,0x02,"Command timeout during processing"}, 989 {0x2E,0x03,"Command timeout during processing due to error recovery"}, 990 {0x2F,0x00,"Commands cleared by another initiator"}, 991 {0x2F,0x01,"Commands cleared by power loss notification"}, 992 {0x2F,0x02,"Commands cleared by device server"}, 993 {0x2F,0x03,"Some commands cleared by queuing layer event"}, 994 {0x30,0x00,"Incompatible medium installed"}, 995 {0x30,0x01,"Cannot read medium - unknown format"}, 996 {0x30,0x02,"Cannot read medium - incompatible format"}, 997 {0x30,0x03,"Cleaning cartridge installed"}, 998 {0x30,0x04,"Cannot write medium - unknown format"}, 999 {0x30,0x05,"Cannot write medium - incompatible format"}, 1000 {0x30,0x06,"Cannot format medium - incompatible medium"}, 1001 {0x30,0x07,"Cleaning failure"}, 1002 {0x30,0x08,"Cannot write - application code mismatch"}, 1003 {0x30,0x09,"Current session not fixated for append"}, 1004 {0x30,0x0A,"Cleaning request rejected"}, 1005 {0x30,0x0B,"Cleaning tape expired"}, 1006 {0x30,0x0C,"WORM medium - overwrite attempted"}, 1007 {0x30,0x0D,"WORM medium - integrity check"}, 1008 {0x30,0x10,"Medium not formatted"}, 1009 {0x30,0x11,"Incompatible volume type"}, 1010 {0x30,0x12,"Incompatible volume qualifier"}, 1011 {0x30,0x13,"Cleaning volume expired"}, 1012 {0x31,0x00,"Medium format corrupted"}, 1013 {0x31,0x01,"Format command failed"}, 1014 {0x31,0x02,"Zoned formatting failed due to spare linking"}, 1015 {0x31,0x03,"Sanitize command failed"}, 1016 {0x32,0x00,"No defect spare location available"}, 1017 {0x32,0x01,"Defect list update failure"}, 1018 {0x33,0x00,"Tape length error"}, 1019 {0x34,0x00,"Enclosure failure"}, 1020 {0x35,0x00,"Enclosure services failure"}, 1021 {0x35,0x01,"Unsupported enclosure function"}, 1022 {0x35,0x02,"Enclosure services unavailable"}, 1023 {0x35,0x03,"Enclosure services transfer failure"}, 1024 {0x35,0x04,"Enclosure services transfer refused"}, 1025 {0x35,0x05,"Enclosure services checksum error"}, 1026 {0x36,0x00,"Ribbon, ink, or toner failure"}, 1027 {0x37,0x00,"Rounded parameter"}, 1028 {0x38,0x00,"Event status notification"}, 1029 {0x38,0x02,"Esn - power management class event"}, 1030 {0x38,0x04,"Esn - media class event"}, 1031 {0x38,0x06,"Esn - device busy class event"}, 1032 {0x38,0x07,"Thin provisioning soft threshold reached"}, 1033 {0x39,0x00,"Saving parameters not supported"}, 1034 {0x3A,0x00,"Medium not present"}, 1035 {0x3A,0x01,"Medium not present - tray closed"}, 1036 {0x3A,0x02,"Medium not present - tray open"}, 1037 {0x3A,0x03,"Medium not present - loadable"}, 1038 {0x3A,0x04,"Medium not present - medium auxiliary memory accessible"}, 1039 {0x3B,0x00,"Sequential positioning error"}, 1040 {0x3B,0x01,"Tape position error at beginning-of-medium"}, 1041 {0x3B,0x02,"Tape position error at end-of-medium"}, 1042 {0x3B,0x03,"Tape or electronic vertical forms unit not ready"}, 1043 {0x3B,0x04,"Slew failure"}, 1044 {0x3B,0x05,"Paper jam"}, 1045 {0x3B,0x06,"Failed to sense top-of-form"}, 1046 {0x3B,0x07,"Failed to sense bottom-of-form"}, 1047 {0x3B,0x08,"Reposition error"}, 1048 {0x3B,0x09,"Read past end of medium"}, 1049 {0x3B,0x0A,"Read past beginning of medium"}, 1050 {0x3B,0x0B,"Position past end of medium"}, 1051 {0x3B,0x0C,"Position past beginning of medium"}, 1052 {0x3B,0x0D,"Medium destination element full"}, 1053 {0x3B,0x0E,"Medium source element empty"}, 1054 {0x3B,0x0F,"End of medium reached"}, 1055 {0x3B,0x11,"Medium magazine not accessible"}, 1056 {0x3B,0x12,"Medium magazine removed"}, 1057 {0x3B,0x13,"Medium magazine inserted"}, 1058 {0x3B,0x14,"Medium magazine locked"}, 1059 {0x3B,0x15,"Medium magazine unlocked"}, 1060 {0x3B,0x16,"Mechanical positioning or changer error"}, 1061 {0x3B,0x17,"Read past end of user object"}, 1062 {0x3B,0x18,"Element disabled"}, 1063 {0x3B,0x19,"Element enabled"}, 1064 {0x3B,0x1a,"Data transfer device removed"}, 1065 {0x3B,0x1b,"Data transfer device inserted"}, 1066 {0x3B,0x1c,"Too many logical objects on partition to support operation"}, 1067 {0x3D,0x00,"Invalid bits in identify message"}, 1068 {0x3E,0x00,"Logical unit has not self-configured yet"}, 1069 {0x3E,0x01,"Logical unit failure"}, 1070 {0x3E,0x02,"Timeout on logical unit"}, 1071 {0x3E,0x03,"Logical unit failed self-test"}, 1072 {0x3E,0x04,"Logical unit unable to update self-test log"}, 1073 {0x3F,0x00,"Target operating conditions have changed"}, 1074 {0x3F,0x01,"Microcode has been changed"}, 1075 {0x3F,0x02,"Changed operating definition"}, 1076 {0x3F,0x03,"Inquiry data has changed"}, 1077 {0x3F,0x04,"Component device attached"}, 1078 {0x3F,0x05,"Device identifier changed"}, 1079 {0x3F,0x06,"Redundancy group created or modified"}, 1080 {0x3F,0x07,"Redundancy group deleted"}, 1081 {0x3F,0x08,"Spare created or modified"}, 1082 {0x3F,0x09,"Spare deleted"}, 1083 {0x3F,0x0A,"Volume set created or modified"}, 1084 {0x3F,0x0B,"Volume set deleted"}, 1085 {0x3F,0x0C,"Volume set deassigned"}, 1086 {0x3F,0x0D,"Volume set reassigned"}, 1087 {0x3F,0x0E,"Reported luns data has changed"}, 1088 {0x3F,0x0F,"Echo buffer overwritten"}, 1089 {0x3F,0x10,"Medium loadable"}, 1090 {0x3F,0x11,"Medium auxiliary memory accessible"}, 1091 {0x3F,0x12,"iSCSI IP address added"}, 1092 {0x3F,0x13,"iSCSI IP address removed"}, 1093 {0x3F,0x14,"iSCSI IP address changed"}, 1094 {0x3F,0x15,"Inspect referrals sense descriptors"}, 1095 {0x3F,0x16,"Microcode has been changed without reset"}, 1096 {0x3F,0x17,"Zone transition to full"}, 1097 {0x3F,0x18,"Bind completed"}, 1098 {0x3F,0x19,"Bind redirected"}, 1099 {0x3F,0x1A,"Subsidiary binding changed"}, 1100 1101 /* 1102 * ASC 0x40, 0x41 and 0x42 overridden by "additional2" array entries 1103 * for ascq > 1. Preferred error message for this group is 1104 * "Diagnostic failure on component nn (80h-ffh)". 1105 */ 1106 {0x40,0x00,"Ram failure (should use 40 nn)"}, 1107 {0x41,0x00,"Data path failure (should use 40 nn)"}, 1108 {0x42,0x00,"Power-on or self-test failure (should use 40 nn)"}, 1109 1110 {0x43,0x00,"Message error"}, 1111 {0x44,0x00,"Internal target failure"}, 1112 {0x44,0x01,"Persistent reservation information lost"}, 1113 {0x44,0x71,"ATA device failed Set Features"}, 1114 {0x45,0x00,"Select or reselect failure"}, 1115 {0x46,0x00,"Unsuccessful soft reset"}, 1116 {0x47,0x00,"SCSI parity error"}, 1117 {0x47,0x01,"Data phase CRC error detected"}, 1118 {0x47,0x02,"SCSI parity error detected during st data phase"}, 1119 {0x47,0x03,"Information unit iuCRC error detected"}, 1120 {0x47,0x04,"Asynchronous information protection error detected"}, 1121 {0x47,0x05,"Protocol service CRC error"}, 1122 {0x47,0x06,"Phy test function in progress"}, 1123 {0x47,0x7F,"Some commands cleared by iSCSI protocol event"}, 1124 {0x48,0x00,"Initiator detected error message received"}, 1125 {0x49,0x00,"Invalid message error"}, 1126 {0x4A,0x00,"Command phase error"}, 1127 {0x4B,0x00,"Data phase error"}, 1128 {0x4B,0x01,"Invalid target port transfer tag received"}, 1129 {0x4B,0x02,"Too much write data"}, 1130 {0x4B,0x03,"Ack/nak timeout"}, 1131 {0x4B,0x04,"Nak received"}, 1132 {0x4B,0x05,"Data offset error"}, 1133 {0x4B,0x06,"Initiator response timeout"}, 1134 {0x4B,0x07,"Connection lost"}, 1135 {0x4B,0x08,"Data-in buffer overflow - data buffer size"}, 1136 {0x4B,0x09,"Data-in buffer overflow - data buffer descriptor area"}, 1137 {0x4B,0x0A,"Data-in buffer error"}, 1138 {0x4B,0x0B,"Data-out buffer overflow - data buffer size"}, 1139 {0x4B,0x0C,"Data-out buffer overflow - data buffer descriptor area"}, 1140 {0x4B,0x0D,"Data-out buffer error"}, 1141 {0x4B,0x0E,"PCIe fabric error"}, 1142 {0x4B,0x0f,"PCIe completion timeout"}, 1143 {0x4B,0x10,"PCIe completer abort"}, 1144 {0x4B,0x11,"PCIe poisoned tlp received"}, 1145 {0x4B,0x12,"PCIe ecrc check failed"}, 1146 {0x4B,0x13,"PCIe unsupported request"}, 1147 {0x4B,0x14,"PCIe acs violation"}, 1148 {0x4B,0x15,"PCIe tlp prefix blocked"}, 1149 {0x4C,0x00,"Logical unit failed self-configuration"}, 1150 /* 1151 * ASC 0x4D overridden by an "additional2" array entry 1152 * so there is no need to have them here. 1153 */ 1154 /* {0x4D,0x00,"Tagged overlapped commands (nn = queue tag)"}, */ 1155 1156 {0x4E,0x00,"Overlapped commands attempted"}, 1157 {0x50,0x00,"Write append error"}, 1158 {0x50,0x01,"Write append position error"}, 1159 {0x50,0x02,"Position error related to timing"}, 1160 {0x51,0x00,"Erase failure"}, 1161 {0x51,0x01,"Erase failure - incomplete erase operation detected"}, 1162 {0x52,0x00,"Cartridge fault"}, 1163 {0x53,0x00,"Media load or eject failed"}, 1164 {0x53,0x01,"Unload tape failure"}, 1165 {0x53,0x02,"Medium removal prevented"}, 1166 {0x53,0x03,"Medium removal prevented by data transfer element"}, 1167 {0x53,0x04,"Medium thread or unthread failure"}, 1168 {0x53,0x05,"Volume identifier invalid"}, 1169 {0x53,0x06,"Volume identifier missing"}, 1170 {0x53,0x07,"Duplicate volume identifier"}, 1171 {0x53,0x08,"Element status unknown"}, 1172 {0x53,0x09,"Data transfer device error - load failed"}, 1173 {0x53,0x0A,"Data transfer device error - unload failed"}, 1174 {0x53,0x0B,"Data transfer device error - unload missing"}, 1175 {0x53,0x0C,"Data transfer device error - eject failed"}, 1176 {0x53,0x0D,"Data transfer device error - library communication failed"}, 1177 {0x54,0x00,"SCSI to host system interface failure"}, 1178 {0x55,0x00,"System resource failure"}, 1179 {0x55,0x01,"System buffer full"}, 1180 {0x55,0x02,"Insufficient reservation resources"}, 1181 {0x55,0x03,"Insufficient resources"}, 1182 {0x55,0x04,"Insufficient registration resources"}, 1183 {0x55,0x05,"Insufficient access control resources"}, 1184 {0x55,0x06,"Auxiliary memory out of space"}, 1185 {0x55,0x07,"Quota error"}, 1186 {0x55,0x08,"Maximum number of supplemental decryption keys exceeded"}, 1187 {0x55,0x09,"Medium auxiliary memory not accessible"}, 1188 {0x55,0x0a,"Data currently unavailable"}, 1189 {0x55,0x0b,"Insufficient power for operation"}, 1190 {0x55,0x0c,"Insufficient resources to create rod"}, 1191 {0x55,0x0d,"Insufficient resources to create rod token"}, 1192 {0x55,0x0e,"Insufficient zone resources"}, 1193 {0x55,0x0f,"Insufficient zone resources to complete write"}, 1194 {0x55,0x10,"Maximum number of streams open"}, 1195 {0x55,0x11,"Insufficient resources to bind"}, 1196 {0x57,0x00,"Unable to recover table-of-contents"}, 1197 {0x58,0x00,"Generation does not exist"}, 1198 {0x59,0x00,"Updated block read"}, 1199 {0x5A,0x00,"Operator request or state change input"}, 1200 {0x5A,0x01,"Operator medium removal request"}, 1201 {0x5A,0x02,"Operator selected write protect"}, 1202 {0x5A,0x03,"Operator selected write permit"}, 1203 {0x5B,0x00,"Log exception"}, 1204 {0x5B,0x01,"Threshold condition met"}, 1205 {0x5B,0x02,"Log counter at maximum"}, 1206 {0x5B,0x03,"Log list codes exhausted"}, 1207 {0x5C,0x00,"Rpl status change"}, 1208 {0x5C,0x01,"Spindles synchronized"}, 1209 {0x5C,0x02,"Spindles not synchronized"}, 1210 {0x5D,0x00,"Failure prediction threshold exceeded"}, 1211 {0x5D,0x01,"Media failure prediction threshold exceeded"}, 1212 {0x5D,0x02,"Logical unit failure prediction threshold exceeded"}, 1213 {0x5D,0x03,"spare area exhaustion prediction threshold exceeded"}, 1214 {0x5D,0x10,"Hardware impending failure general hard drive failure"}, 1215 {0x5D,0x11,"Hardware impending failure drive error rate too high" }, 1216 {0x5D,0x12,"Hardware impending failure data error rate too high" }, 1217 {0x5D,0x13,"Hardware impending failure seek error rate too high" }, 1218 {0x5D,0x14,"Hardware impending failure too many block reassigns"}, 1219 {0x5D,0x15,"Hardware impending failure access times too high" }, 1220 {0x5D,0x16,"Hardware impending failure start unit times too high" }, 1221 {0x5D,0x17,"Hardware impending failure channel parametrics"}, 1222 {0x5D,0x18,"Hardware impending failure controller detected"}, 1223 {0x5D,0x19,"Hardware impending failure throughput performance"}, 1224 {0x5D,0x1A,"Hardware impending failure seek time performance"}, 1225 {0x5D,0x1B,"Hardware impending failure spin-up retry count"}, 1226 {0x5D,0x1C,"Hardware impending failure drive calibration retry count"}, 1227 {0x5D,0x1D,"Hardware impending failure power loss protection circuit"}, 1228 {0x5D,0x20,"Controller impending failure general hard drive failure"}, 1229 {0x5D,0x21,"Controller impending failure drive error rate too high" }, 1230 {0x5D,0x22,"Controller impending failure data error rate too high" }, 1231 {0x5D,0x23,"Controller impending failure seek error rate too high" }, 1232 {0x5D,0x24,"Controller impending failure too many block reassigns"}, 1233 {0x5D,0x25,"Controller impending failure access times too high" }, 1234 {0x5D,0x26,"Controller impending failure start unit times too high" }, 1235 {0x5D,0x27,"Controller impending failure channel parametrics"}, 1236 {0x5D,0x28,"Controller impending failure controller detected"}, 1237 {0x5D,0x29,"Controller impending failure throughput performance"}, 1238 {0x5D,0x2A,"Controller impending failure seek time performance"}, 1239 {0x5D,0x2B,"Controller impending failure spin-up retry count"}, 1240 {0x5D,0x2C,"Controller impending failure drive calibration retry count"}, 1241 {0x5D,0x30,"Data channel impending failure general hard drive failure"}, 1242 {0x5D,0x31,"Data channel impending failure drive error rate too high" }, 1243 {0x5D,0x32,"Data channel impending failure data error rate too high" }, 1244 {0x5D,0x33,"Data channel impending failure seek error rate too high" }, 1245 {0x5D,0x34,"Data channel impending failure too many block reassigns"}, 1246 {0x5D,0x35,"Data channel impending failure access times too high" }, 1247 {0x5D,0x36,"Data channel impending failure start unit times too high" }, 1248 {0x5D,0x37,"Data channel impending failure channel parametrics"}, 1249 {0x5D,0x38,"Data channel impending failure controller detected"}, 1250 {0x5D,0x39,"Data channel impending failure throughput performance"}, 1251 {0x5D,0x3A,"Data channel impending failure seek time performance"}, 1252 {0x5D,0x3B,"Data channel impending failure spin-up retry count"}, 1253 {0x5D,0x3C,"Data channel impending failure drive calibration retry count"}, 1254 {0x5D,0x40,"Servo impending failure general hard drive failure"}, 1255 {0x5D,0x41,"Servo impending failure drive error rate too high" }, 1256 {0x5D,0x42,"Servo impending failure data error rate too high" }, 1257 {0x5D,0x43,"Servo impending failure seek error rate too high" }, 1258 {0x5D,0x44,"Servo impending failure too many block reassigns"}, 1259 {0x5D,0x45,"Servo impending failure access times too high" }, 1260 {0x5D,0x46,"Servo impending failure start unit times too high" }, 1261 {0x5D,0x47,"Servo impending failure channel parametrics"}, 1262 {0x5D,0x48,"Servo impending failure controller detected"}, 1263 {0x5D,0x49,"Servo impending failure throughput performance"}, 1264 {0x5D,0x4A,"Servo impending failure seek time performance"}, 1265 {0x5D,0x4B,"Servo impending failure spin-up retry count"}, 1266 {0x5D,0x4C,"Servo impending failure drive calibration retry count"}, 1267 {0x5D,0x50,"Spindle impending failure general hard drive failure"}, 1268 {0x5D,0x51,"Spindle impending failure drive error rate too high" }, 1269 {0x5D,0x52,"Spindle impending failure data error rate too high" }, 1270 {0x5D,0x53,"Spindle impending failure seek error rate too high" }, 1271 {0x5D,0x54,"Spindle impending failure too many block reassigns"}, 1272 {0x5D,0x55,"Spindle impending failure access times too high" }, 1273 {0x5D,0x56,"Spindle impending failure start unit times too high" }, 1274 {0x5D,0x57,"Spindle impending failure channel parametrics"}, 1275 {0x5D,0x58,"Spindle impending failure controller detected"}, 1276 {0x5D,0x59,"Spindle impending failure throughput performance"}, 1277 {0x5D,0x5A,"Spindle impending failure seek time performance"}, 1278 {0x5D,0x5B,"Spindle impending failure spin-up retry count"}, 1279 {0x5D,0x5C,"Spindle impending failure drive calibration retry count"}, 1280 {0x5D,0x60,"Firmware impending failure general hard drive failure"}, 1281 {0x5D,0x61,"Firmware impending failure drive error rate too high" }, 1282 {0x5D,0x62,"Firmware impending failure data error rate too high" }, 1283 {0x5D,0x63,"Firmware impending failure seek error rate too high" }, 1284 {0x5D,0x64,"Firmware impending failure too many block reassigns"}, 1285 {0x5D,0x65,"Firmware impending failure access times too high" }, 1286 {0x5D,0x66,"Firmware impending failure start unit times too high" }, 1287 {0x5D,0x67,"Firmware impending failure channel parametrics"}, 1288 {0x5D,0x68,"Firmware impending failure controller detected"}, 1289 {0x5D,0x69,"Firmware impending failure throughput performance"}, 1290 {0x5D,0x6A,"Firmware impending failure seek time performance"}, 1291 {0x5D,0x6B,"Firmware impending failure spin-up retry count"}, 1292 {0x5D,0x6C,"Firmware impending failure drive calibration retry count"}, 1293 {0x5D,0x73,"Media impending failure endurance limit met"}, 1294 {0x5D,0xFF,"Failure prediction threshold exceeded (false)"}, 1295 {0x5E,0x00,"Low power condition on"}, 1296 {0x5E,0x01,"Idle condition activated by timer"}, 1297 {0x5E,0x02,"Standby condition activated by timer"}, 1298 {0x5E,0x03,"Idle condition activated by command"}, 1299 {0x5E,0x04,"Standby condition activated by command"}, 1300 {0x5E,0x05,"Idle_b condition activated by timer"}, 1301 {0x5E,0x06,"Idle_b condition activated by command"}, 1302 {0x5E,0x07,"Idle_c condition activated by timer"}, 1303 {0x5E,0x08,"Idle_c condition activated by command"}, 1304 {0x5E,0x09,"Standby_y condition activated by timer"}, 1305 {0x5E,0x0a,"Standby_y condition activated by command"}, 1306 {0x5E,0x41,"Power state change to active"}, 1307 {0x5E,0x42,"Power state change to idle"}, 1308 {0x5E,0x43,"Power state change to standby"}, 1309 {0x5E,0x45,"Power state change to sleep"}, 1310 {0x5E,0x47,"Power state change to device control"}, 1311 {0x60,0x00,"Lamp failure"}, 1312 {0x61,0x00,"Video acquisition error"}, 1313 {0x61,0x01,"Unable to acquire video"}, 1314 {0x61,0x02,"Out of focus"}, 1315 {0x62,0x00,"Scan head positioning error"}, 1316 {0x63,0x00,"End of user area encountered on this track"}, 1317 {0x63,0x01,"Packet does not fit in available space"}, 1318 {0x64,0x00,"Illegal mode for this track"}, 1319 {0x64,0x01,"Invalid packet size"}, 1320 {0x65,0x00,"Voltage fault"}, 1321 {0x66,0x00,"Automatic document feeder cover up"}, 1322 {0x66,0x01,"Automatic document feeder lift up"}, 1323 {0x66,0x02,"Document jam in automatic document feeder"}, 1324 {0x66,0x03,"Document miss feed automatic in document feeder"}, 1325 {0x67,0x00,"Configuration failure"}, 1326 {0x67,0x01,"Configuration of incapable logical units failed"}, 1327 {0x67,0x02,"Add logical unit failed"}, 1328 {0x67,0x03,"Modification of logical unit failed"}, 1329 {0x67,0x04,"Exchange of logical unit failed"}, 1330 {0x67,0x05,"Remove of logical unit failed"}, 1331 {0x67,0x06,"Attachment of logical unit failed"}, 1332 {0x67,0x07,"Creation of logical unit failed"}, 1333 {0x67,0x08,"Assign failure occurred"}, 1334 {0x67,0x09,"Multiply assigned logical unit"}, 1335 {0x67,0x0A,"Set target port groups command failed"}, 1336 {0x67,0x0B,"ATA device feature not enabled"}, 1337 {0x67,0x0C,"Command rejected"}, 1338 {0x67,0x0D,"Explicit bind not allowed"}, 1339 {0x68,0x00,"Logical unit not configured"}, 1340 {0x68,0x01,"Subsidiary logical unit not configured"}, 1341 {0x69,0x00,"Data loss on logical unit"}, 1342 {0x69,0x01,"Multiple logical unit failures"}, 1343 {0x69,0x02,"Parity/data mismatch"}, 1344 {0x6A,0x00,"Informational, refer to log"}, 1345 {0x6B,0x00,"State change has occurred"}, 1346 {0x6B,0x01,"Redundancy level got better"}, 1347 {0x6B,0x02,"Redundancy level got worse"}, 1348 {0x6C,0x00,"Rebuild failure occurred"}, 1349 {0x6D,0x00,"Recalculate failure occurred"}, 1350 {0x6E,0x00,"Command to logical unit failed"}, 1351 {0x6F,0x00,"Copy protection key exchange failure - authentication " 1352 "failure"}, 1353 {0x6F,0x01,"Copy protection key exchange failure - key not present"}, 1354 {0x6F,0x02,"Copy protection key exchange failure - key not established"}, 1355 {0x6F,0x03,"Read of scrambled sector without authentication"}, 1356 {0x6F,0x04,"Media region code is mismatched to logical unit region"}, 1357 {0x6F,0x05,"Drive region must be permanent/region reset count error"}, 1358 {0x6F,0x06,"Insufficient block count for binding nonce recording"}, 1359 {0x6F,0x07,"Conflict in binding nonce recording"}, 1360 {0x6F,0x08,"Insufficient permission"}, 1361 {0x6F,0x09,"Invalid drive-host pairing server"}, 1362 {0x6F,0x0A,"Drive-host pairing suspended"}, 1363 /* 1364 * ASC 0x70 overridden by an "additional2" array entry 1365 * so there is no need to have them here. 1366 */ 1367 /* {0x70,0x00,"Decompression exception short algorithm id of nn"}, */ 1368 1369 {0x71,0x00,"Decompression exception long algorithm id"}, 1370 {0x72,0x00,"Session fixation error"}, 1371 {0x72,0x01,"Session fixation error writing lead-in"}, 1372 {0x72,0x02,"Session fixation error writing lead-out"}, 1373 {0x72,0x03,"Session fixation error - incomplete track in session"}, 1374 {0x72,0x04,"Empty or partially written reserved track"}, 1375 {0x72,0x05,"No more track reservations allowed"}, 1376 {0x72,0x06,"RMZ extension is not allowed"}, 1377 {0x72,0x07,"No more test zone extensions are allowed"}, 1378 {0x73,0x00,"CD control error"}, 1379 {0x73,0x01,"Power calibration area almost full"}, 1380 {0x73,0x02,"Power calibration area is full"}, 1381 {0x73,0x03,"Power calibration area error"}, 1382 {0x73,0x04,"Program memory area update failure"}, 1383 {0x73,0x05,"Program memory area is full"}, 1384 {0x73,0x06,"RMA/PMA is almost full"}, 1385 {0x73,0x10,"Current power calibration area almost full"}, 1386 {0x73,0x11,"Current power calibration area is full"}, 1387 {0x73,0x17,"RDZ is full"}, 1388 {0x74,0x00,"Security error"}, 1389 {0x74,0x01,"Unable to decrypt data"}, 1390 {0x74,0x02,"Unencrypted data encountered while decrypting"}, 1391 {0x74,0x03,"Incorrect data encryption key"}, 1392 {0x74,0x04,"Cryptographic integrity validation failed"}, 1393 {0x74,0x05,"Error decrypting data"}, 1394 {0x74,0x06,"Unknown signature verification key"}, 1395 {0x74,0x07,"Encryption parameters not useable"}, 1396 {0x74,0x08,"Digital signature validation failure"}, 1397 {0x74,0x09,"Encryption mode mismatch on read"}, 1398 {0x74,0x0a,"Encrypted block not raw read enabled"}, 1399 {0x74,0x0b,"Incorrect Encryption parameters"}, 1400 {0x74,0x0c,"Unable to decrypt parameter list"}, 1401 {0x74,0x0d,"Encryption algorithm disabled"}, 1402 {0x74,0x10,"SA creation parameter value invalid"}, 1403 {0x74,0x11,"SA creation parameter value rejected"}, 1404 {0x74,0x12,"Invalid SA usage"}, 1405 {0x74,0x21,"Data encryption configuration prevented"}, 1406 {0x74,0x30,"SA creation parameter not supported"}, 1407 {0x74,0x40,"Authentication failed"}, 1408 {0x74,0x61,"External data encryption key manager access error"}, 1409 {0x74,0x62,"External data encryption key manager error"}, 1410 {0x74,0x63,"External data encryption key not found"}, 1411 {0x74,0x64,"External data encryption request not authorized"}, 1412 {0x74,0x6e,"External data encryption control timeout"}, 1413 {0x74,0x6f,"External data encryption control error"}, 1414 {0x74,0x71,"Logical unit access not authorized"}, 1415 {0x74,0x79,"Security conflict in translated device"}, 1416 {0, 0, NULL} 1417}; 1418 1419#else /* SG_SCSI_STRINGS */ 1420 1421struct sg_lib_asc_ascq_range_t sg_lib_asc_ascq_range[] = 1422{ 1423 {0, 0, 0, NULL} 1424}; 1425 1426struct sg_lib_asc_ascq_t sg_lib_asc_ascq[] = 1427{ 1428 {0, 0, NULL} 1429}; 1430#endif /* SG_SCSI_STRINGS */ 1431 1432const char * sg_lib_sense_key_desc[] = { 1433 "No Sense", /* Filemark, ILI and/or EOM; progress 1434 indication (during FORMAT); power 1435 condition sensing (REQUEST SENSE) */ 1436 "Recovered Error", /* The last command completed successfully 1437 but used error correction */ 1438 "Not Ready", /* The addressed target is not ready */ 1439 "Medium Error", /* Data error detected on the medium */ 1440 "Hardware Error", /* Controller or device failure */ 1441 "Illegal Request", 1442 "Unit Attention", /* Removable medium was changed, or 1443 the target has been reset */ 1444 "Data Protect", /* Access to the data is blocked */ 1445 "Blank Check", /* Reached unexpected written or unwritten 1446 region of the medium */ 1447 "Vendor specific(9)", /* Vendor specific */ 1448 "Copy Aborted", /* COPY or COMPARE was aborted */ 1449 "Aborted Command", /* The target aborted the command */ 1450 "Equal", /* SEARCH DATA found data equal (obsolete) */ 1451 "Volume Overflow", /* Medium full with data to be written */ 1452 "Miscompare", /* Source data and data on the medium 1453 do not agree */ 1454 "Completed" /* may occur for successful cmd (spc4r23) */ 1455}; 1456 1457const char * sg_lib_pdt_strs[32] = { /* should have 2**5 elements */ 1458 /* 0 */ "disk", 1459 "tape", 1460 "printer", /* obsolete, spc5r01 */ 1461 "processor", /* often SAF-TE device, copy manager */ 1462 "write once optical disk", /* obsolete, spc5r01 */ 1463 /* 5 */ "cd/dvd", 1464 "scanner", /* obsolete */ 1465 "optical memory device", 1466 "medium changer", 1467 "communications", /* obsolete */ 1468 /* 0xa */ "graphics [0xa]", /* obsolete */ 1469 "graphics [0xb]", /* obsolete */ 1470 "storage array controller", 1471 "enclosure services device", 1472 "simplified direct access device", 1473 "optical card reader/writer device", 1474 /* 0x10 */ "bridge controller commands", 1475 "object based storage", 1476 "automation/driver interface", 1477 "security manager device", /* obsolete, spc5r01 */ 1478 "zoned block commands", 1479 "0x15", "0x16", "0x17", "0x18", 1480 "0x19", "0x1a", "0x1b", "0x1c", "0x1d", 1481 "well known logical unit", 1482 "no physical device on this lu", 1483}; 1484 1485const char * sg_lib_transport_proto_strs[] = 1486{ 1487 "Fibre Channel Protocol for SCSI (FCP-4)", 1488 "SCSI Parallel Interface (SPI-5)", /* obsolete in spc5r01 */ 1489 "Serial Storage Architecture SCSI-3 Protocol (SSA-S3P)", 1490 "Serial Bus Protocol for IEEE 1394 (SBP-3)", 1491 "SCSI RDMA Protocol (SRP)", 1492 "Internet SCSI (iSCSI)", 1493 "Serial Attached SCSI Protocol (SPL-4)", 1494 "Automation/Drive Interface Transport (ADT-2)", 1495 "AT Attachment Interface (ACS-2)", /* 0x8 */ 1496 "USB Attached SCSI (UAS-2)", 1497 "SCSI over PCI Express (SOP)", 1498 "PCIe", /* added in spc5r02 */ 1499 "Oxc", "Oxd", "Oxe", 1500 "No specific protocol" 1501}; 1502 1503/* SCSI Feature Sets array. code->value, pdt->peri_dev_type (-1 for SPC) */ 1504struct sg_lib_value_name_t sg_lib_scsi_feature_sets[] = 1505{ 1506 {SCSI_FS_SPC_DISCOVERY_2016, -1, "Discovery 2016"}, 1507 {SCSI_FS_SBC_BASE_2010, PDT_DISK, "SBC Base 2010"}, 1508 {SCSI_FS_SBC_BASE_2016, PDT_DISK, "SBC Base 2016"}, 1509 {SCSI_FS_SBC_BASIC_PROV_2016, PDT_DISK, "Basic provisioning 2016"}, 1510 {SCSI_FS_SBC_DRIVE_MAINT_2016, PDT_DISK, "Drive maintenance 2016"}, 1511 {0x0, 0, NULL}, /* 0x0 is reserved sfs; trailing sentinel */ 1512}; 1513 1514#if (SG_SCSI_STRINGS && HAVE_NVME && (! IGNORE_NVME)) 1515 1516/* .value is completion queue's DW3 as follows: ((DW3 >> 17) & 0x3ff) 1517 * .peri_dev_type is an index for the sg_lib_scsi_status_sense_arr[] 1518 * .name is taken from NVMe 1.3a document, section 4.6.1.2.1 with less 1519 * capitalization. 1520 * NVMe term bits 31:17 of DW3 in the completion field as the "Status 1521 * Field" (SF). Bit 31 is "Do not retry" (DNR) and bit 30 is "More" (M). 1522 * Bits 29:28 are reserved, bit 27:25 are the "Status Code Type" (SCT) 1523 * and bits 24:17 are the Status Code (SC). This table is in ascending 1524 * order of its .value field so a binary search could be done on it. */ 1525struct sg_lib_value_name_t sg_lib_nvme_cmd_status_arr[] = 1526{ 1527 /* Generic command status values, Status Code Type (SCT): 0h 1528 * Lowest 8 bits are the Status Code (SC), in this case: 1529 * 00h - 7Fh: Applicable to Admin Command Set, or across multiple 1530 * command sets 1531 * 80h - BFh: I/O Command Set Specific status codes 1532 * c0h - FFh: I/O Vendor Specific status codes */ 1533 {0x0, 0, "Successful completion"}, 1534 {0x1, 1, "Invalid command opcode"}, 1535 {0x2, 2, "Invalid field in command"}, 1536 {0x3, 2, "Command id conflict"}, 1537 {0x4, 3, "Data transfer error"}, 1538 {0x5, 4, "Command aborted due to power loss notication"}, 1539 {0x6, 5, "Internal error"}, 1540 {0x7, 6, "Command abort requested"}, 1541 {0x8, 6, "Command aborted due to SQ deletion"}, 1542 {0x9, 6, "Command aborted due to failed fused command"}, 1543 {0xa, 6, "Command aborted due to missing fused command"}, 1544 {0xb, 7, "Invalid namespace or format"}, 1545 {0xc, 5, "Command sequence error"}, 1546 {0xd, 5, "Invalid SGL segment descriptor"}, 1547 {0xe, 5, "Invalid number of SGL descriptors"}, 1548 {0xf, 5, "Data SGL length invalid"}, 1549 {0x10, 5, "Matadata SGL length invalid"}, 1550 {0x11, 5, "SGL descriptor type invalid"}, 1551 {0x12, 5, "Invalid use of controller memory buffer"}, 1552 {0x13, 5, "PRP offset invalid"}, 1553 {0x14, 2, "Atomic write unit exceeded"}, 1554 {0x15, 8, "Operation denied"}, 1555 {0x16, 5, "SGL offset invalid"}, 1556 {0x17, 5, "Reserved [0x17]"}, 1557 {0x18, 5, "Host identifier inconsistent format"}, 1558 {0x19, 5, "Keep alive timeout expired"}, 1559 {0x1a, 5, "Keep alive timeout invalid"}, 1560 {0x1b, 6, "Command aborted due to Preempt and Abort"}, 1561 {0x1c, 10, "Sanitize failed"}, 1562 {0x1d, 11, "Sanitize in progress"}, 1563 {0x1e, 5, "SGL data block granularity invalid"}, 1564 {0x1f, 5, "Command not supported for queue in CMB"}, 1565 1566 /* Generic command status values, NVM (I/O) Command Set */ 1567 {0x80, 12, "LBA out of range"}, 1568 {0x81, 3, "Capacity exceeded"}, 1569 {0x82, 13, "Namespace not ready"}, 1570 {0x83, 14, "Reservation conflict"}, 1571 {0x84, 15, "Format in progress"}, 1572 /* 0xc0 - 0xff: vendor specific */ 1573 1574 /* Command specific status values, Status Code Type (SCT): 1h */ 1575 {0x100, 5, "Completion queue invalid"}, 1576 {0x101, 5, "Invalid queue identifier"}, 1577 {0x102, 5, "Invalid queue size"}, 1578 {0x103, 5, "Abort command limit exceeded"}, 1579 {0x104, 5, "Reserved [0x104]"}, 1580 {0x105, 5, "Asynchronous event request limit exceeded"}, 1581 {0x106, 5, "Invalid firmware slot"}, 1582 {0x107, 5, "Invalid firmware image"}, 1583 {0x108, 5, "Invalid interrupt vector"}, 1584 {0x109, 5, "Invalid log page"}, 1585 {0x10a,16, "Invalid format"}, 1586 {0x10b, 5, "Firmware activation requires conventional reset"}, 1587 {0x10c, 5, "Invalid queue deletion"}, 1588 {0x10d, 5, "Feature identifier not saveable"}, 1589 {0x10e, 5, "Feature not changeable"}, 1590 {0x10f, 5, "Feature not namespace specific"}, 1591 {0x110, 5, "Firmware activation requires NVM subsystem reset"}, 1592 {0x111, 5, "Firmware activation requires reset"}, 1593 {0x112, 5, "Firmware activation requires maximum time violation"}, 1594 {0x113, 5, "Firmware activation prohibited"}, 1595 {0x114, 5, "Overlapping range"}, 1596 {0x115, 5, "Namespace insufficient capacity"}, 1597 {0x116, 5, "Namespace identifier unavailable"}, 1598 {0x117, 5, "Reserved [0x107]"}, 1599 {0x118, 5, "Namespace already attached"}, 1600 {0x119, 5, "Namespace is private"}, 1601 {0x11a, 5, "Namespace not attached"}, 1602 {0x11b, 3, "Thin provisioning not supported"}, 1603 {0x11c, 3, "Controller list invalid"}, 1604 {0x11d,17, "Device self-test in progress"}, 1605 {0x11e,18, "Boot partition write prohibited"}, 1606 {0x11f, 5, "Invalid controller identifier"}, 1607 {0x120, 5, "Invalid secondary controller state"}, 1608 {0x121, 5, "Invalid number of controller resorces"}, 1609 {0x122, 5, "Invalid resorce identifier"}, 1610 1611 /* Command specific status values, Status Code Type (SCT): 1h 1612 * for NVM (I/O) Command Set */ 1613 {0x180, 2, "Conflicting attributes"}, 1614 {0x181,19, "Invalid protection information"}, 1615 {0x182,18, "Attempted write to read only range"}, 1616 /* 0x1c0 - 0x1ff: vendor specific */ 1617 1618 /* Media and Data Integrity error values, Status Code Type (SCT): 2h */ 1619 {0x280,20, "Write fault"}, 1620 {0x281,21, "Unrecovered read error"}, 1621 {0x282,22, "End-to-end guard check error"}, 1622 {0x283,23, "End-to-end application tag check error"}, 1623 {0x284,24, "End-to-end reference tag check error"}, 1624 {0x285,25, "Compare failure"}, 1625 {0x286, 8, "Access denied"}, 1626 {0x287,26, "Deallocated or unwritten logical block"}, 1627 /* 0x2c0 - 0x2ff: vendor specific */ 1628 1629 /* Leave this Sentinel value at end of this array */ 1630 {0x3ff, 0, NULL}, 1631}; 1632 1633/* The sg_lib_nvme_cmd_status_arr[n].peri_dev_type field is an index 1634 * to this array. It allows an NVMe status (error) value to be mapped 1635 * to this SCSI tuple: status, sense_key, additional sense code (asc) and 1636 * asc qualifier (ascq). For brevity SAM_STAT_CHECK_CONDITION is written 1637 * as 0x2. */ 1638struct sg_lib_4tuple_u8 sg_lib_scsi_status_sense_arr[] = 1639{ 1640 {SAM_STAT_GOOD, SPC_SK_NO_SENSE, 0, 0}, /* it's all good */ /* 0 */ 1641 {SAM_STAT_CHECK_CONDITION, SPC_SK_ILLEGAL_REQUEST, 0x20, 0x0},/* opcode */ 1642 {0x2, SPC_SK_ILLEGAL_REQUEST, 0x24, 0x0}, /* field in cdb */ 1643 {0x2, SPC_SK_MEDIUM_ERROR, 0x0, 0x0}, 1644 {SAM_STAT_TASK_ABORTED, SPC_SK_ABORTED_COMMAND, 0xb, 0x8}, 1645 {0x2, SPC_SK_HARDWARE_ERROR, 0x44, 0x0}, /* internal error */ /* 5 */ 1646 {SAM_STAT_TASK_ABORTED, SPC_SK_ABORTED_COMMAND, 0x0, 0x0}, 1647 {0x2, SPC_SK_ILLEGAL_REQUEST, 0x20, 0x9}, /* invalid LU */ 1648 {0x2, SPC_SK_ILLEGAL_REQUEST, 0x20, 0x2}, /* access denied */ 1649 {0x2, SPC_SK_ILLEGAL_REQUEST, 0x2c, 0x0}, /* cmd sequence error */ 1650 {0x2, SPC_SK_MEDIUM_ERROR, 0x31, 0x3}, /* sanitize failed */ /* 10 */ 1651 {0x2, SPC_SK_NOT_READY, 0x4, 0x1b}, /* sanitize in progress */ 1652 {0x2, SPC_SK_ILLEGAL_REQUEST, 0x21, 0x0}, /* LBA out of range */ 1653 {0x2, SPC_SK_NOT_READY, 0x4, 0x0}, /* not reportable; 0x1: becoming */ 1654 {SAM_STAT_RESERVATION_CONFLICT, 0x0, 0x0, 0x0}, 1655 {0x2, SPC_SK_NOT_READY, 0x4, 0x4}, /* format in progress */ /* 15 */ 1656 {0x2, SPC_SK_ILLEGAL_REQUEST, 0x31, 0x1}, /* format failed */ 1657 {0x2, SPC_SK_NOT_READY, 0x4, 0x9}, /* self-test in progress */ 1658 {0x2, SPC_SK_DATA_PROTECT, 0x27, 0x0}, /* write prohibited */ 1659 {0x2, SPC_SK_ILLEGAL_REQUEST, 0x10, 0x5}, /* protection info */ 1660 {0x2, SPC_SK_MEDIUM_ERROR, 0x3, 0x0}, /* periph dev w fault */ /* 20 */ 1661 {0x2, SPC_SK_MEDIUM_ERROR, 0x11, 0x0}, /* unrecoc rd */ 1662 {0x2, SPC_SK_MEDIUM_ERROR, 0x10, 0x1}, /* PI guard */ 1663 {0x2, SPC_SK_MEDIUM_ERROR, 0x10, 0x2}, /* PI app tag */ 1664 {0x2, SPC_SK_MEDIUM_ERROR, 0x10, 0x2}, /* PI app tag */ 1665 {0x2, SPC_SK_MISCOMPARE, 0x1d, 0x0}, /* during verify */ /* 25 */ 1666 {0x2, SPC_SK_MEDIUM_ERROR, 0x21, 0x6}, /* read invalid data */ 1667 1668 /* Leave this Sentinel value at end of this array */ 1669 {0xff, 0xff, 0xff, 0xff}, 1670}; 1671 1672 1673#else /* (SG_SCSI_STRINGS && HAVE_NVME && (! IGNORE_NVME)) */ 1674struct sg_lib_value_name_t sg_lib_nvme_cmd_status_arr[] = 1675{ 1676 1677 /* Leave this Sentinel value at end of this array */ 1678 {0x3ff, 0, NULL}, 1679}; 1680 1681struct sg_lib_4tuple_u8 sg_lib_scsi_status_sense_arr[] = 1682{ 1683 1684 /* Leave this Sentinel value at end of this array */ 1685 {0xff, 0xff, 0xff, 0xff}, 1686}; 1687 1688#endif /* (SG_SCSI_STRINGS && HAVE_NVME && (! IGNORE_NVME)) */ 1689