| d2b0f6f77ee525811b6efe864efa6a4eb82eea73 |
|
24-Apr-2014 |
Gavin Shan <gwshan@linux.vnet.ibm.com> |
powerpc/eeh: No hotplug on permanently removed dev
The issue was detected in a bit complicated test case where
we have multiple hierarchical PEs shown as following figure:
+-----------------+
| PE#3 p2p#0 |
| p2p#1 |
+-----------------+
|
+-----------------+
| PE#4 pdev#0 |
| pdev#1 |
+-----------------+
PE#4 (have 2 PCI devices) is the child of PE#3, which has 2 p2p
bridges. We accidentally had less-known scenario: PE#4 was removed
permanently from the system because of permanent failure (e.g.
exceeding the max allowd failure times in last hour), then we detects
EEH errors on PE#3 and tried to recover it. However, eeh_dev instances
for pdev#0/1 were not detached from PE#4, which was still connected to
PE#3. All of that was because of the fact that we rely on count-based
pcibios_release_device(), which isn't reliable enough. When doing
recovery for PE#3, we still apply hotplug on PE#4 and pdev#0/1, which
are not valid any more. Eventually, we run into kernel crash.
The patch fixes above issue from two aspects. For unplug, we simply
skip those permanently removed PE, whose state is (EEH_PE_STATE_ISOLATED
&& !EEH_PE_STATE_RECOVERING) and its frozen count should be greater
than EEH_MAX_ALLOWED_FREEZES. For plug, we marked all permanently
removed EEH devices with EEH_DEV_REMOVED and return 0xFF's on read
its PCI config so that PCI core will omit them.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| 3ab96a02e829131c19db8ed99239289acdb4e3dc |
|
08-Sep-2012 |
Gavin Shan <shangw@linux.vnet.ibm.com> |
powerpc/eeh: Cleanup on EEH PCI address cache
The patch does cleanup on EEH PCI address cache based on the fact
EEH core is the only user of the component.
* Cleanup on function names so that they all have prefix
"eeh" and looks more short.
* Function printk() has been replaced with pr_debug() or
pr_warning() accordingly.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| f8f7d63fd96ead101415a1302035137a866f8998 |
|
08-Sep-2012 |
Gavin Shan <shangw@linux.vnet.ibm.com> |
powerpc/eeh: Trace eeh device from I/O cache
The idea comes from Benjamin Herrenschmidt. The eeh cache helps
fetching the pci device according to the given I/O address. Since
the eeh cache is serving for eeh, it's reasonable for eeh cache
to trace eeh device except pci device.
The patch make eeh cache to trace eeh device. Also, the major
eeh entry function eeh_dn_check_failure has been renamed to
eeh_dev_check_failure since it will take eeh device as input
parameter.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| d7bb88629dd64242fbbd7dd34ecad073afdbafad |
|
08-Sep-2012 |
Gavin Shan <shangw@linux.vnet.ibm.com> |
powerpc/eeh: Probe mode support
While EEH module is installed, PCI devices is checked one by one
to see if it supports eeh. On different platforms, the PCI devices
are referred through different ways when the EEH module is loaded.
For example, on pSeries platform, that is done by OF node. However,
we would do that by real PCI devices (struct pci_dev) on PowerNV
platform in future. So we needs some mechanism to differentiate
those cases by classifying them to probe modes, either from OF
nodes or real PCI devices.
The patch implements the support to eeh probe mode. Also, the
EEH on pSeries has set it into EEH_PROBE_MODE_DEVTREE. That means
the probe will be done based on OF nodes on pSeries platform.
In addition, On pSeries platform, it's done by OF nodes. The patch
moves the the probe function from EEH core to platform dependent
backend and some cleanup applied.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| c270a24c59bd9a4ac7dbcbd964cbd14270b3a361 |
|
08-Sep-2012 |
Gavin Shan <shangw@linux.vnet.ibm.com> |
powerpc/eeh: Do reset based on PE
The patch implements reset based on PE instead of eeh device. Also,
The functions used to retrieve the reset type, either hot or fundamental
reset, have been reworked for a little bit. More specificly, it's
implemented based the the eeh device traverse function.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| ff477966c626e440dd1737801ae4d52cf1f22bff |
|
08-Sep-2012 |
Gavin Shan <shangw@linux.vnet.ibm.com> |
powerpc/eeh: I/O enable and log retrival based on PE
The patch refactors the original implementation in order to enable
I/O and retrieve EEH log based on PE.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| 9e6d2cf65e3dbaf783917c92c15d31d419b0d648 |
|
08-Sep-2012 |
Gavin Shan <shangw@linux.vnet.ibm.com> |
powerpc/eeh: Device bars restore based on PE
The patch introduces the function to traverse the devices of the
specified PE and its child PEs. Also, the restore on device bars
is implemented based on the traverse function.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| 66523d9f2d799de901a5ae7bbed6c3f663fb0b00 |
|
08-Sep-2012 |
Gavin Shan <shangw@linux.vnet.ibm.com> |
powerpc/eeh: Trace error based on PE from beginning
There're 2 conditions to trigger EEH error detection: invalid value
returned from reading I/O or config space. On each case, the function
eeh_dn_check_failure will be called to initialize EEH event and put
it into the poll for further processing.
The patch changes the function for a little bit so that the EEH error
will be traced based on PE instead of EEH device any more. Also, the
function eeh_find_device_pe() has been removed since the eeh device
is tracing the PE by struct eeh_dev::pe.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| 5b6635294418a954b5f911375b86d3552cf93f36 |
|
08-Sep-2012 |
Gavin Shan <shangw@linux.vnet.ibm.com> |
powerpc/eeh: Trace EEH state based on PE
Since we've introduced dedicated struct to trace individual PEs,
it's reasonable to trace its state through the dedicated struct
instead of using "eeh_dev" any more.
The patches implements the state tracing based on PE. It's notable
that the PE state will be applied to the specified PE as well as
its child PEs. That complies with the rule that problematic parent
PE will prevent those child PEs from working properly.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| f631acd3e98c31b21937682d2b3f39bf9333a18e |
|
27-Feb-2012 |
Gavin Shan <shangw@linux.vnet.ibm.com> |
powerpc/eeh: Replace pci_dn with eeh_dev for EEH core
The original EEH implementation is heavily depending on struct pci_dn.
We have to put EEH related information to pci_dn. Actually, we could
split struct pci_dn so that the EEH sensitive information to form an
individual struct, then EEH looks more independent.
The patch replaces pci_dn with eeh_dev for EEH core.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| def9d83da4f8587dbad5ea57c57d91e53a51006a |
|
27-Feb-2012 |
Gavin Shan <shangw@linux.vnet.ibm.com> |
powerpc/eeh: Cleanup function names in EEH aux components
The patch does some cleanup on the function names of EEH
aux components. Currently, only couple of function names from
eeh_cache have been adjusted so that:
* The function name has prefix "eeh_addr_cache".
* Move around pci_addr_cache_build() in the header file
to reflect function call sequence.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| 1823fbf119e434dd3fb8eb7482613994c09d8527 |
|
27-Feb-2012 |
Gavin Shan <shangw@linux.vnet.ibm.com> |
powerpc/eeh: pseries platform EEH configure bridge
In order to enable particular PCI device, which has been included
in the parent PE. The involved PCI bridges should be enabled explicitly
if there has. On pSeries platform, there're dedicated RTAS calls
to fulfil the purpose.
The patch implements the function of configuring PCI bridges through
the dedicated RTAS calls. Besides, the function has been abstracted
by struct eeh_ops::configure_bridge so that the EEH core components
could support multiple platforms in future.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| 8d633291b4fc0539ecad31f972447104be6953ec |
|
27-Feb-2012 |
Gavin Shan <shangw@linux.vnet.ibm.com> |
powerpc/eeh: pseries platform EEH error log retrieval
On RTAS compliant pSeries platform, one dedicated RTAS call has
been introduced to retrieve EEH temporary or permanent error log.
The patch implements the function of retriving EEH error log through
RTAS call. Besides, it has been abstracted by struct eeh_ops::get_log
so that EEH core components could support multiple platforms in future.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| b0e5f742f1816bebedabeb6844be1a598bd50a91 |
|
27-Feb-2012 |
Gavin Shan <shangw@linux.vnet.ibm.com> |
powerpc/eeh: pseries platform EEH wait PE state
On pSeries platform, the PE state might be temporarily unavailable.
In that case, the firmware will return the corresponding wait time.
That means the kernel has to wait for appropriate time in order to
get the PE state.
The patch does the implementation for that. Besides, the function
has been abstracted through struct eeh_ops::wait_state so that EEH core
components could support multiple platforms in future.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| 8fb8f709025c13ae72968a66a1ade24431a342b2 |
|
27-Feb-2012 |
Gavin Shan <shangw@linux.vnet.ibm.com> |
powerpc/eeh: pseries platform EEH operations
There're 4 EEH operations that are covered by the dedicated RTAS
call <ibm,set-eeh-option>: enable or disable EEH, enable MMIO and
enable DMA. At early stage of system boot, the EEH would be tried
to enable on PCI device related device node. MMIO and DMA for
particular PE should be enabled when doing recovery on EEH errors
so that the PE could function properly again.
The patch implements it and abstract that through struct
eeh_ops::set_eeh. It would be help for EEH to support multiple
platforms in future.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| cce4b2d243ddd9e8d5da159b893117afd7ccad5c |
|
27-Feb-2012 |
Gavin Shan <shangw@linux.vnet.ibm.com> |
powerpc/eeh: Cleanup function names in the EEH core
The EEH has been implemented on pSeries platform. The original
code looks a little bit nasty. The patch does cleanup on the
current EEH implementation so that it looks more clean.
* Try adding prefix "eeh" for functions.
* Some function names have been adjusted so that they looks
shorter and meaningful.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| cb3bc9d0de1e247268622acd40e0d2f8120f299c |
|
27-Feb-2012 |
Gavin Shan <shangw@linux.vnet.ibm.com> |
powerpc/eeh: Cleanup comments in the EEH core
The EEH has been implemented on pSeries platform. The original
code looks a little bit nasty. The patch does cleanup on the
current EEH implementation so that it looks more clean.
* Duplicated comments have been removed from the corresponding
header files.
* Comments have been reorganized so that it looks more clean.
* The leading comments of functions are adjusted for a little
bit so that the result of "make pdfdocs" would be more
unified.
* Function definitions and calls have unified format as "xxx()".
That means the format "xxx ()" has been replaced by "xxx()".
* There're multiple functions implemented for resetting PE. The
position of those functions have been move around so that they
are adjacent to each other to reflect their relationship.
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| 673c975624895c4db2edff32601d9c6475b2d39e |
|
24-Feb-2012 |
Bjorn Helgaas <bhelgaas@google.com> |
powerpc/PCI: replace pci_probe_only with pci_flags
We already use pci_flags, so this just sets pci_flags directly and removes
the intermediate step of figuring out pci_probe_only, then using it to set
pci_flags.
The PCI core provides a pci_flags definition (currently __weak), so drop
the powerpc definitions in favor of that.
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
| 778a785f02ad846446e91dab49331bd7d853c514 |
|
11-Jan-2012 |
Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> |
powerpc/pseries/eeh: Fix crash when error happens during device probe
EEH may happen during a PCI driver probe. If the driver is trying to
access some register in a loop, the EEH code will try to print the
driver name. But the driver pointer in struct pci_dev is not set until
probe returns successfully.
Use a function to test if the device and the driver pointer is NULL
before accessing the driver's name.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| dda804ad4023cc202466c46fcfcc163131953838 |
|
15-Sep-2010 |
Nishanth Aravamudan <nacc@us.ibm.com> |
powerpc/pci: Fix return type of BUID_{HI,LO} macros
BUID_HI and BUID_LO are used to pass data to call_rtas, which expects
ints or u32s. But the macro doesn't cast the return, so the result is
still u64. Use the upper_32_bits and lower_32_bits macros that have been
added to kernel.h.
Found by getting printf format errors trying to debug print the args, no
actual code change for 64 bit kernels where the macros are actually
used.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| 8d3d50bf1913561ef3b1f5b53115c5a481ba9b1e |
|
03-Feb-2010 |
Breno Leitao <leitao@linux.vnet.ibm.com> |
powerpc/eeh: Fix a bug when pci structure is null
During a EEH recover, the pci_dev structure can be null, mainly if an
eeh event is detected during cpi config operation. In this case, the
pci_dev will not be known (and will be null) the kernel will crash
with the following message:
Unable to handle kernel paging request for data at address 0x000000a0
Faulting instruction address: 0xc00000000006b8b4
Oops: Kernel access of bad area, sig: 11 [#1]
NIP [c00000000006b8b4] .eeh_event_handler+0x10c/0x1a0
LR [c00000000006b8a8] .eeh_event_handler+0x100/0x1a0
Call Trace:
[c0000003a80dff00] [c00000000006b8a8] .eeh_event_handler+0x100/0x1a0
[c0000003a80dff90] [c000000000031f1c] .kernel_thread+0x54/0x70
The bug occurs because pci_name() tries to access a null pointer.
This patch just guarantee that pci_name() is not called on Null pointers.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| 0ed2c722c650513ba4bce868c7a052e576c060e2 |
|
28-Aug-2009 |
Grant Likely <grant.likely@secretlab.ca> |
powerpc/pci: Merge ppc32 and ppc64 versions of phb_scan()
The two versions are doing almost exactly the same thing. No need to
maintain them as separate files. This patch also has the side effect
of making the PCI device tree scanning code available to 32 bit powerpc
machines, but no board ports actually make use of this feature at this
point.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| b8b572e1015f81b4e748417be2629dfe51ab99f9 |
|
01-Aug-2008 |
Stephen Rothwell <sfr@canb.auug.org.au> |
powerpc: Move include files to arch/powerpc/include/asm
from include/asm-powerpc. This is the result of a
mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm
Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly. Of the latter only
one was outside the arch code and it is a driver only built for powerpc.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|