| 6606110d89aefcb21b9e70adfe064987cbd8393a |
|
12-Sep-2014 |
Joe Perches <joe@perches.com> |
mmc: Convert pr_warning to pr_warn
Use the much more common pr_warn instead of pr_warning.
Other miscellanea:
o Coalesce formats
o Realign arguments
o Remove extra spaces when coalescing formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
| 3d705d14fe4c72be83bae1610680e209ee226b9d |
|
19-Aug-2014 |
Sascha Hauer <s.hauer@pengutronix.de> |
mmc: implement Driver Stage Register handling
Some eMMC and SD cards implement a DSR register that allows to tune
raise/fall times and drive strength of the CMD and DATA outputs.
The values to use depend on the card in use and the host.
It might be needed to reduce the drive strength to prevent voltage peaks
above the host's specification.
Implement a 'dsr' devicetree property that allows to specify the value
to set the DSR to. For non-dt setups the new members of mmc_host can be
set by board code.
This patch was initially authored by Sascha Hauer. It contains
improvements authored by Markus Niebel and Uwe Kleine-König.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
| b9ec26160f998493509b782be999ff59e4372971 |
|
28-Jan-2014 |
Ulf Hansson <ulf.hansson@linaro.org> |
mmc: core: Fixup busy detection for mmc switch operations
If the host controller supports busy detection in HW, we expect the
MMC_CAP_WAIT_WHILE_BUSY to be set. Likewise the corresponding
host->max_busy_timeout should reflect the maximum busy detection
timeout supported by the host.
Previously we expected a host that supported MMC_CAP_WAIT_WHILE_BUSY to
cope with any timeout, which just isn't feasible due to HW limitations.
For most switch operations, R1B responses are expected and thus we need
to check for busy detection completion. To cope with cases where the
requested busy detection timeout is greater than what the host are able
to support, we fallback to use a R1 response instead. This will prevent
the host from doing HW busy detection.
In those cases, busy detection completion is handled by polling the for
the card's status using CMD13. This is the same mechanism used when the
host doesn't support MMC_CAP_WAIT_WHILE_BUSY.
Do note, a host->max_busy_timeout set to zero, is interpreted by the
mmc core as it don't know what the host supports. It will then provide
the host with whatever timeout the mmc core finds suitable.
For some cases the mmc core has unfurtunate no clue of what timeout to
use. In these cases we provide the host with a timeout value of zero,
which the host may interpret as use whatever timeout it finds suitable.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
| 636bd13c12d2331ad835b89681428eccb4cf102e |
|
28-Jan-2014 |
Ulf Hansson <ulf.hansson@linaro.org> |
mmc: core: Minor simplifications to __mmc_switch
Instead of using several references to card->host, let's use a local
variable. That means we can remove the BUG_ON verifications for the
same pointers.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
| 4509f847751c9d2a724f37fe831393fbac34b80f |
|
08-Jan-2014 |
Ulf Hansson <ulf.hansson@linaro.org> |
mmc: core: Add ignore_crc flag to __mmc_switch
Instead of handle specific adaptations, releated to certain switch
operations, inside __mmc_switch, push this to be handled by the caller
instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
| 1d4d77444bf4212c44585146a2b353ca24c815f9 |
|
08-Jan-2014 |
Ulf Hansson <ulf.hansson@linaro.org> |
mmc: core: Rename cmd_timeout_ms to busy_timeout
To better reflect that the cmd_timeout_ms is directly related to the
busy detection timeout, let's rename it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
| ecd3a7dad982aeba6409ef6d933fd7e372a70127 |
|
28-Oct-2013 |
Ulf Hansson <ulf.hansson@linaro.org> |
mmc: core: Silence compiler warning in __mmc_switch
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
| 878e200bbb1fbde9f21582decab95b178e5a3b83 |
|
09-Sep-2013 |
Ulf Hansson <ulf.hansson@linaro.org> |
mmc: core: Do not poll for busy with status cmd for all switch cmds
Some switch operations like poweroff notify, shall according to the
spec not be followed by any other new commands. For these cases and
when the host does'nt support MMC_CAP_WAIT_WHILE_BUSY, we must not
send status commands to poll for busy detection. Instead wait for
the stated timeout from the EXT_CSD before completing the request.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
| a27fbf2f067b0cd6f172c8b696b9a44c58bfaa7a |
|
04-Sep-2013 |
Seungwon Jeon <tgih.jun@samsung.com> |
mmc: add ignorance case for CMD13 CRC error
While speed mode is changed, CMD13 cannot be guaranteed.
According to the spec., it is not recommended to use CMD13
to check the busy completion of the timing change.
If CMD13 is used in this case, CRC error must be ignored.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
| 84532e33975bd8fc969c77c8a2a980df2ec096a5 |
|
25-Aug-2013 |
Minjian Wu <minjianwu@micron.com> |
mmc: core: Set data timeout for mmc bus test commands (CMD14 and CMD19).
Signed-off-by: Minjian Wu <minjianwu@micron.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
| 07a682160866e302d696f5c76d74024d575fb79d |
|
19-Apr-2013 |
Ulf Hansson <ulf.hansson@linaro.org> |
mmc: core: Restructure and simplify code for mmc sleep|awake
The mmc_card_sleep|awake APIs are not being used since the support is
already properly encapsulated within the suspend sequence. Sleep|awake
command is also specific for eMMC.
We remove the sleep|awake bus_ops, the mmc_card_sleep|awake APIs and
move the code into the mmc specific core instead. This also includes
the mmc ops function, mmc_sleepawake. All releated functions have then
become static and we have got far less code to maintain.
Additionally this patch also simplifies the code from mmc_sleepawake,
since it is only used to put the card to sleep and not awake.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
| 775a9362b5d7e006ff6bbec5cb9c9c9d5a751696 |
|
18-Apr-2013 |
Maya Erez <merez@codeaurora.org> |
mmc: card: Adding support for sanitize in eMMC 4.5
The sanitize support is added as a user-app ioctl call, and
was removed from the block-device request, since its purpose is
to be invoked not via File-System but by a user.
This feature deletes the unmap memory region of the eMMC card,
by writing to a specific register in the EXT_CSD.
unmap region is the memory region that was previously deleted
(by erase, trim or discard operation).
In order to avoid timeout when sanitizing large-scale cards,
the timeout for sanitize operation is 240 seconds.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
| ce39f9d17c14e56ea6772aa84393e6e0cc8499c4 |
|
06-Feb-2013 |
Seungwon Jeon <tgih.jun@samsung.com> |
mmc: support packed write command for eMMC4.5 devices
This patch supports packed write command of eMMC4.5 devices. Several
writes can be grouped in packed command and all data of the individual
commands can be sent in a single transfer on the bus. Large amounts of
data in one transfer rather than several data of small size are
effective for eMMC write internally. As a result, packed command help
write throughput be improved. The following tables show the results
of packed write.
Type A:
test none | packed
iozone 25.8 | 31
tiotest 27.6 | 31.2
lmdd 31.2 | 35.4
Type B:
test none | packed
iozone 44.1 | 51.1
tiotest 47.9 | 52.5
lmdd 51.6 | 59.2
Type C:
test none | packed
iozone 19.5 | 32
tiotest 19.9 | 34.5
lmdd 22.8 | 40.7
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
| 8fee476b219d1869762d9ef5c189a0c85e919a4d |
|
16-Nov-2012 |
Trey Ramsay <tramsay@linux.vnet.ibm.com> |
mmc: core: Fix some driver hangs when dealing with broken devices
There are infinite loops in the mmc code that can be caused by bad
hardware. The code will loop forever if the device never comes back
from program mode, R1_STATE_PRG, and it is not ready for data,
R1_READY_FOR_DATA.
A long timeout is added to prevent the code from looping forever.
The timeout will occur if the device never comes back from program
state or the device never becomes ready for data.
It's not clear whether the timeout will do more than log a pr_err()
and then start a fresh hang all over again. We may need to extend
this patch later to perform some kind of reset of the device (is
that possible?) or rejection of new I/O to the device.
Signed-off-by: Trey Ramsay <tramsay@linux.vnet.ibm.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
| 950d56acce5d401f477b91d0177605b543d63d07 |
|
17-Sep-2012 |
Jaehoon Chung <jh80.chung@samsung.com> |
mmc: support BKOPS feature for eMMC
Enable eMMC background operations (BKOPS) feature.
If URGENT_BKOPS is set after a response, note that BKOPS are required.
Immediately run BKOPS if required. Read/write operations should be
requested during BKOPS(LEVEL-1), then issue HPI to interrupt the
ongoing BKOPS and service the foreground operation.
(This patch only controls the LEVEL2/3.)
When repeating the writing 1GB data, at a certain time, performance is
decreased. At that time, card triggers the Level-3 or Level-2. After
running bkops, performance is recovered.
Future considerations:
* Check BKOPS_LEVEL=1 and start BKOPS in a preventive manner.
* Interrupt ongoing BKOPS before powering off the card.
* How do we get BKOPS_STATUS value (periodically send ext_csd command)?
* If using periodic bkops, also consider runtime_pm control.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
| 1a41313e7f8c5b724a2e3ff66558dbe811844423 |
|
03-Aug-2012 |
Kyungsik Lee <kyungsik.lee@lge.com> |
mmc: core: Remove bounce buffer in mmc_send_cxd_data()
It is expected that Extended CSD register (the size of this register
is larger than CID/CSD) will be referenced more frequently as more
fields have been added to Extended CSD and it seems that it is not
a good option to double the memory used.
This patch is intended to avoid the use of bounce buffer for reading
Extended CSD register in mmc_send_cxd_data(). It will provide a better
performance gain by removing memcpy() overhead for a half KiB and
a redundant bounce buffer allocated repeatedly at the cost of providing
DMA-capable buffer from upper caller (but on-stack buffer is allowed
with no performance gain).
Signed-off-by: Kyungsik Lee <kyungsik.lee@lge.com>
Reviewed-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
| 6af9e96e052a6d1a760c60cb340c5a6584cb92db |
|
22-Jun-2012 |
Venkatraman S <svenkatr@ti.com> |
mmc: core: Fix the HPI execution sequence
mmc_execute_hpi should send the HPI command only once, and only
if the card is in PRG state.
According to eMMC spec, the command's completion time is
not dependent on OUT_OF_INTERRUPT_TIME. Only the transition
out of PRG STATE is guarded by OUT_OF_INTERRUPT_TIME - which
is defined to begin at the end of sending the command itself.
Specify the default timeout for the actual sending of HPI
command, and then use OUT_OF_INTERRUPT_TIME to wait for
the transition out of PRG state.
Reported-by: Alex Lemberg <Alex.Lemberg@sandisk.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
| 2378975bd5ed583da555c7e5dee121663b7d5f46 |
|
12-Mar-2012 |
Jaehoon Chung <jh80.chung@samsung.com> |
mmc: core: warn when card doesn't support HPI
Someone could use send_hpi_cmd() on a card that doesn't advertise support
for HPI. Then maybe didn't work fine. Because card->ext_csd.hpi_cmd
didn't set. So if card didn't support hpi, return the warning message.
And CMD12's flags is MMC_RSP_R1B.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
| 3ef77af154b03776c6c662c68c6332719e9eecac |
|
10-Jul-2011 |
Paul Gortmaker <paul.gortmaker@windriver.com> |
mmc: Add export.h for EXPORT_SYMBOL/THIS_MODULE as required
These two basic defines were everywhere, simply because module.h
was also everywhere. But we are cleaning up the latter. So make
the exporters actually call out their need for the include.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
| eb0d8f135b6730d6d0324a064664d121334290e7 |
|
18-Oct-2011 |
Jaehoon Chung <jh80.chung@samsung.com> |
mmc: core: support HPI send command
HPI command is defined in eMMC4.41.
This feature is important for eMMC4.5 devices.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
| a3c76eb9d4a1e68a69dd880cf0bcb8a52418b993 |
|
11-Oct-2011 |
Girish K S <girish.shivananjappa@linaro.org> |
mmc: replace printk with appropriate display macro
All the files using printk function for displaying kernel messages
in the mmc driver have been replaced with corresponding macro.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
| ad5fd97288655b5628052c1fa906419417c86100 |
|
24-Aug-2011 |
Venkatraman S <svenkatr@ti.com> |
mmc: fix integer assignments to pointer
Fix the sparse warning output "warning: Using plain integer as NULL pointer"
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
| 7435bb7950ba8a3cbfa6d0c01e92588562533a3f |
|
10-Aug-2011 |
Jaehoon Chung <jh80.chung@samsung.com> |
mmc: core: use defined R1_STATE_PRG macro for card status
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
| 24f5b53ba076e983bc64fa48534ca795d7813d51 |
|
14-Apr-2011 |
Chris Ball <cjb@laptop.org> |
mmc: initialize struct mmc_request at declaration time
Converts from:
struct mmc_request mrq;
memset(&mrq, 0, sizeof(struct mmc_request));
to:
struct mmc_request mrq = {0};
because it's shorter, as performant, and easier to work out whether
initialization has happened.
Signed-off-by: Chris Ball <cjb@laptop.org>
|
| a61ad2b49bfce94dfddce828cd9222e4b9e7825b |
|
14-Apr-2011 |
Chris Ball <cjb@laptop.org> |
mmc: initialize struct mmc_data at declaration time
Converts from:
struct mmc_data data;
memset(&data, 0, sizeof(struct mmc_data));
to:
struct mmc_data data = {0};
because it's shorter, as performant, and easier to work out whether
initialization has happened.
Signed-off-by: Chris Ball <cjb@laptop.org>
|
| 1278dba167f01bb3c6626d16450d31129d041087 |
|
14-Apr-2011 |
Chris Ball <cjb@laptop.org> |
mmc: initialize struct mmc_command at declaration time
Converts from:
struct mmc_command cmd;
memset(&cmd, 0, sizeof(struct mmc_command));
to:
struct mmc_command cmd = {0};
because it's shorter, as performant, and easier to work out whether
initialization has happened.
Signed-off-by: Chris Ball <cjb@laptop.org>
|
| d3a8d95dcbb726b9cf0bbc166b2473bdd236c88c |
|
11-Apr-2011 |
Andrei Warkentin <andreiw@motorola.com> |
mmc: core: Allow setting CMD timeout for CMD6 (SWITCH).
CMD6 is an R1B-type command, where DAT is used as busy. Depending
on register written using CMD6, timeout value can be different
as per spec.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
| 25985edcedea6396277003854657b5f3cb31a628 |
|
31-Mar-2011 |
Lucas De Marchi <lucas.demarchi@profusion.mobi> |
Fix common misspellings
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
| 22113efd00491310da802f3b1a9a66cfcf415fac |
|
15-Dec-2010 |
Aries Lee <arieslee@jmicron.com> |
mmc: Test bus-width for old MMC devices
Some old MMC devices fail with the 4/8 bits the driver tries to use
exclusively. This patch adds a test for the given bus setup and falls
back to the lower bit mode (until 1-bit mode) when the test fails.
[Major rework and refactoring by tiwai]
[Quirk addition and many fixes by prakity]
Signed-off-by: Aries Lee <arieslee@jmicron.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
| 5a0e3ad6af8660be21ca98a971cd00f331318c05 |
|
24-Mar-2010 |
Tejun Heo <tj@kernel.org> |
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
| ef0b27d4ccacac32afc3d1c0e8a95e4091dfbc8c |
|
23-Sep-2009 |
Adrian Hunter <adrian.hunter@nokia.com> |
mmc: check status after MMC SWITCH command
According to the standard, the SWITCH command should be followed by a
SEND_STATUS command to check for errors.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| b1ebe38456f7fe61a88af2844361e763ac6ea5ae |
|
23-Sep-2009 |
Jarkko Lavinen <jarkko.lavinen@nokia.com> |
mmc: add mmc card sleep and awake support
Add support for the new MMC command SLEEP_AWAKE.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
| cda56ac29f2d8288d62978272856884d26e0b47b |
|
10-Feb-2009 |
Adrian Hunter <adrian.hunter@nokia.com> |
mmc: fix data timeout for SEND_EXT_CSD
Commit 0d3e0460f307e84904968aad6cff97bd688583d8
"MMC: CSD and CID timeout values" inadvertently broke
the timeout for the MMC command SEND_EXT_CSD.
This patch puts it back again.
Depending on the characteristics of the controller,
this bug may prevent the use of MMC cards.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
| 0d3e0460f307e84904968aad6cff97bd688583d8 |
|
02-Oct-2008 |
Matthew Fleming <matthew.fleming@imgtec.com> |
MMC: CSD and CID timeout values
The MMC spec states that the timeout for accessing the CSD and CID
registers is 64 clock cycles.
Signed-off-by: Matthew Fleming <matthew.fleming@imgtec.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
| 87ae9afdcada236d0a1b38ce2c465a65916961dc |
|
30-Oct-2007 |
Adrian Bunk <bunk@kernel.org> |
cleanup asm/scatterlist.h includes
Not architecture specific code should not #include <asm/scatterlist.h>.
This patch therefore either replaces them with
#include <linux/scatterlist.h> or simply removes them if they were
unused.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
| 78e480731ab89e311ecdb455d04903cafbe163ca |
|
27-Oct-2007 |
Pierre Ossman <drzeus@drzeus.cx> |
mmc: fix cid and csd byte order
MMC over SPI sends the CID and CSD registers as data, not responses,
which means that the host driver won't do the necessary byte flipping
for us.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
| af51715079e7fb6b290e1881d63d815dc4de5011 |
|
08-Aug-2007 |
David Brownell <david-b@pacbell.net> |
MMC core learns about SPI
Teach the MMC/SD/SDIO core about using SPI mode.
- Use mmc_host_is_spi() so enumeration works through SPI signaling
and protocols, not just the native versions.
- Provide the SPI response type flags with each request issued,
including requests from the new lock/unlock code.
- Understand that cmd->resp[0] and mmc_get_status() results for SPI
return different values than for "native" MMC/SD protocol; this
affects resetting, checking card lock status, and some others.
- Understand that some commands act a bit differently ... notably:
* OP_COND command doesn't return the OCR
* APP_CMD status doesn't have an R1_APP_CMD analogue
Those changes required some new and updated primitives:
- Provide utilities to access two SPI-only requests, and one
request that wasn't previously needed:
* mmc_spi_read_ocr() ... SPI only
* mmc_spi_set_crc() ... SPI only (override by module parm)
* mmc_send_cid() ... for use without broadcast mode
- Updated internal routines:
* Previous mmc_send_csd() modified into mmc_send_cxd_native();
it uses native "R2" responses, which include 16 bytes of data.
* Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data()
helper for command-and-data access
* Bugfix to that mmc_send_cxd_data() code: dma-to-stack is
unsafe/nonportable, so kmalloc a bounce buffer instead.
- Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper
- Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use
those helper routines based on whether they're native or SPI
The newest categories of cards supported by the MMC stack aren't expected
to work yet with SPI: MMC or SD cards with over 4GB data, and SDIO.
All those cards support SPI mode, so eventually they should work too.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
| b146d26a61e0feab2f12a98ae83fd352830899c0 |
|
24-Jul-2007 |
Pierre Ossman <drzeus@drzeus.cx> |
mmc: mmc_set_data_timeout() parameter write is redundant
The write parameter in mmc_set_data_timeout() is redundant as the
data structure contains information about the direction of the
transfer.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
| 17b0429dde9ab60f9cee8e07ab28c7dc6cfe6efd |
|
22-Jul-2007 |
Pierre Ossman <drzeus@drzeus.cx> |
mmc: remove custom error codes
Convert the MMC layer to use standard error codes and not its own,
incompatible values.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
| 70f10482c668301c483acded13bf68780ad352b9 |
|
11-Jul-2007 |
Pierre Ossman <drzeus@drzeus.cx> |
mmc: update header file paths
Make sure all headers in the files reflect their true position
in the tree.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|
| da7fbe58d2d347e95af699ddf04d885be6362bbe |
|
24-Dec-2006 |
Pierre Ossman <drzeus@drzeus.cx> |
mmc: Separate out protocol ops
Move protocol operations and definitions into their own files
in an effort to separate protocol handling and bus
arbitration more clearly.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
|