Lines Matching refs:or
8 * Redistribution and use in source and binary forms, with or without
20 * of any contributors may be used to endorse or promote products derived
63 * this list every time a request sense occurs or after completing a non-tagged
114 or SEQ_FLAGS2, SCB_DMA;
157 * either a selection or reselection occurs.
168 or SIMODE1, ENBUSFREE;
219 or SAVED_SCSIID, A;
222 or SAVED_SCSIID, TWIN_CHNLB;
246 * Our first message must be one of IDENTIFY, ABORT, or
261 or SEQ_FLAGS, NO_DISCONNECT;
300 or SEQ_FLAGS, TARGET_CMD_IS_TAGGED;
309 or SEQ_FLAGS, TARG_CMD_PENDING;
317 or SEQ_FLAGS2, TARGET_MSG_PENDING;
338 or SXFRCTL0, SPIOEN|CLRSTCNT|CLRCHN;
345 or SAVED_SCSIID, A;
348 or SAVED_SCSIID, TWIN_CHNLB;
368 or SIMODE1, ENSCSIRST;
372 or SINDEX, SELBUSB;
386 or SINDEX, TEMODE;
398 or SXFRCTL0, FAST20;
419 or SXFRCTL0, SPIOEN;
445 or SXFRCTL0, CLRSTCNT|CLRCHN;
464 or SAVED_LUN, MSG_IDENTIFYFLAG call target_outb;
494 * No more work to do. Either disconnect or not depending
507 or SXFRCTL0, CLRSTCNT|CLRCHN;
540 * The target has dropped ATN (doesn't want to abort or BDR)
542 * buffer for new commands is full, return busy or queue full.
580 or SXFRCTL0, SPIOEN;
606 or SCB_TARGET_DATA_DIR, BSYO call change_phase;
613 /* XXX Watch for ATN or parity errors??? */
627 or CCSCBCTL, CCSCBEN|CCSCBRESET;
632 or DFCNTRL, FIFORESET;
633 mvi DFWADDR, 3; /* Third 64bit word or byte 24 */
636 or DFCNTRL, HDMAEN|FIFOFLUSH;
645 or SXFRCTL0, SPIOEN|CLRSTCNT|CLRCHN;
695 or SXFRCTL0, CLRSTCNT|CLRCHN;
779 or SINDEX, LAST_SEG;
782 or DFCNTRL, PRELOADEN;
831 or DMAPARAMS, DIRECTION;
849 or SEQ_FLAGS, DPHASE;
894 or SXFRCTL1,BITBUCKET;
908 or SINDEX, LAST_SEG;
915 * completes or the target changes phase.
936 * change, and/or the completion of the last segment.
951 or DFCNTRL, FIFOFLUSH;
976 or SCB_RESIDUAL_SGPTR[0], SG_LIST_NULL;
1031 or DFCNTRL, FIFOFLUSH;
1086 or DSCOMMAND1, HADDLDSEL0;
1119 * zero, or the target changes the phase (in light of this,
1123 * or a phase change, so just wait for FIFO empty status.
1183 or SCB_RESIDUAL_SGPTR[0], SG_LIST_NULL;
1215 or DFCNTRL, HDMAEN|DIRECTION|FIFORESET;
1336 or SXFRCTL0, CLRSTCNT|CLRCHN;
1337 or SXFRCTL0, CLRSTCNT|CLRCHN;
1431 or DFCNTRL, FIFOFLUSH;
1437 or DFCNTRL, FIFOFLUSH;
1457 or SEQ_FLAGS, NO_CDB_SENT;
1471 or SCB_CONTROL, STATUS_RCVD;
1501 or SCSISIGO, ATNO, LASTPHASE;
1510 or SINDEX, MSG_IDENTIFYFLAG|DISCENB, SAVED_LUN;
1604 * is a residual or the status byte is something other than STATUS_GOOD (0).
1662 or SCB_SGPTR, SG_RESID_VALID;
1702 * or we want to abort this command. Either way, the target
1710 or SCB_CONTROL,DISCONNECTED;
1725 * since they are only initialized when we go into data_in or data_out.
1744 or SCB_SGPTR, SG_LIST_NULL;
1778 * sure we have a clean start for the next data or command phase.
1786 or SXFRCTL0, CLRSTCNT|CLRCHN;
1810 * Determine whether a target is using tagged or non-tagged
1813 * for this target or the transaction is for a different lun, then
1882 or SEQ_FLAGS, 0x80;
1887 or SEQ_FLAGS, 0x1;
1891 or SEQ_FLAGS, 0x2;
1909 or SEQ_FLAGS, 0x4;
1914 or SEQ_FLAGS, 0x8;
1921 or SEQ_FLAGS, 0x10;
1952 or SCSISIGO, ATNO, LASTPHASE;
1964 * using SCSIBUSL. When we have pulled the ATN line, or we just want to
2029 or SXFRCTL0, SPIOEN;
2098 or CCSCBCTL, CCSCBEN|CCSCBRESET;
2103 or DFCNTRL, HDMAEN|FIFOFLUSH;
2191 * Either post or fetch an SCB from host memory based on the
2214 or CCSCBCTL, CCSCBEN|CCSCBRESET;
2243 or DFCNTRL, HDMAEN|FIFOFLUSH;
2260 * dumps to the FIFO when HCNT == 0 or the
2359 or DSCOMMAND1, HADDLDSEL0;