dme1737.c revision 345a22245451c0fd2c44b2afb5dfb75628b487fa
1/* 2 * dme1737.c - Driver for the SMSC DME1737, Asus A8000, and SMSC SCH311x 3 * Super-I/O chips integrated hardware monitoring features. 4 * Copyright (c) 2007 Juerg Haefliger <juergh@gmail.com> 5 * 6 * This driver is an I2C/ISA hybrid, meaning that it uses the I2C bus to access 7 * the chip registers if a DME1737 (or A8000) is found and the ISA bus if a 8 * SCH311x chip is found. Both types of chips have very similar hardware 9 * monitoring capabilities but differ in the way they can be accessed. 10 * 11 * This program is free software; you can redistribute it and/or modify 12 * it under the terms of the GNU General Public License as published by 13 * the Free Software Foundation; either version 2 of the License, or 14 * (at your option) any later version. 15 * 16 * This program is distributed in the hope that it will be useful, 17 * but WITHOUT ANY WARRANTY; without even the implied warranty of 18 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 19 * GNU General Public License for more details. 20 * 21 * You should have received a copy of the GNU General Public License 22 * along with this program; if not, write to the Free Software 23 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. 24 */ 25 26#include <linux/module.h> 27#include <linux/init.h> 28#include <linux/slab.h> 29#include <linux/jiffies.h> 30#include <linux/i2c.h> 31#include <linux/platform_device.h> 32#include <linux/hwmon.h> 33#include <linux/hwmon-sysfs.h> 34#include <linux/hwmon-vid.h> 35#include <linux/err.h> 36#include <linux/mutex.h> 37#include <asm/io.h> 38 39/* ISA device, if found */ 40static struct platform_device *pdev; 41 42/* Module load parameters */ 43static int force_start; 44module_param(force_start, bool, 0); 45MODULE_PARM_DESC(force_start, "Force the chip to start monitoring inputs"); 46 47static unsigned short force_id; 48module_param(force_id, ushort, 0); 49MODULE_PARM_DESC(force_id, "Override the detected device ID"); 50 51/* Addresses to scan */ 52static unsigned short normal_i2c[] = {0x2c, 0x2d, 0x2e, I2C_CLIENT_END}; 53 54/* Insmod parameters */ 55I2C_CLIENT_INSMOD_1(dme1737); 56 57/* --------------------------------------------------------------------- 58 * Registers 59 * 60 * The sensors are defined as follows: 61 * 62 * Voltages Temperatures 63 * -------- ------------ 64 * in0 +5VTR (+5V stdby) temp1 Remote diode 1 65 * in1 Vccp (proc core) temp2 Internal temp 66 * in2 VCC (internal +3.3V) temp3 Remote diode 2 67 * in3 +5V 68 * in4 +12V 69 * in5 VTR (+3.3V stby) 70 * in6 Vbat 71 * 72 * --------------------------------------------------------------------- */ 73 74/* Voltages (in) numbered 0-6 (ix) */ 75#define DME1737_REG_IN(ix) ((ix) < 5 ? 0x20 + (ix) \ 76 : 0x94 + (ix)) 77#define DME1737_REG_IN_MIN(ix) ((ix) < 5 ? 0x44 + (ix) * 2 \ 78 : 0x91 + (ix) * 2) 79#define DME1737_REG_IN_MAX(ix) ((ix) < 5 ? 0x45 + (ix) * 2 \ 80 : 0x92 + (ix) * 2) 81 82/* Temperatures (temp) numbered 0-2 (ix) */ 83#define DME1737_REG_TEMP(ix) (0x25 + (ix)) 84#define DME1737_REG_TEMP_MIN(ix) (0x4e + (ix) * 2) 85#define DME1737_REG_TEMP_MAX(ix) (0x4f + (ix) * 2) 86#define DME1737_REG_TEMP_OFFSET(ix) ((ix) == 0 ? 0x1f \ 87 : 0x1c + (ix)) 88 89/* Voltage and temperature LSBs 90 * The LSBs (4 bits each) are stored in 5 registers with the following layouts: 91 * IN_TEMP_LSB(0) = [in5, in6] 92 * IN_TEMP_LSB(1) = [temp3, temp1] 93 * IN_TEMP_LSB(2) = [in4, temp2] 94 * IN_TEMP_LSB(3) = [in3, in0] 95 * IN_TEMP_LSB(4) = [in2, in1] */ 96#define DME1737_REG_IN_TEMP_LSB(ix) (0x84 + (ix)) 97static const u8 DME1737_REG_IN_LSB[] = {3, 4, 4, 3, 2, 0, 0}; 98static const u8 DME1737_REG_IN_LSB_SHL[] = {4, 4, 0, 0, 0, 0, 4}; 99static const u8 DME1737_REG_TEMP_LSB[] = {1, 2, 1}; 100static const u8 DME1737_REG_TEMP_LSB_SHL[] = {4, 4, 0}; 101 102/* Fans numbered 0-5 (ix) */ 103#define DME1737_REG_FAN(ix) ((ix) < 4 ? 0x28 + (ix) * 2 \ 104 : 0xa1 + (ix) * 2) 105#define DME1737_REG_FAN_MIN(ix) ((ix) < 4 ? 0x54 + (ix) * 2 \ 106 : 0xa5 + (ix) * 2) 107#define DME1737_REG_FAN_OPT(ix) ((ix) < 4 ? 0x90 + (ix) \ 108 : 0xb2 + (ix)) 109#define DME1737_REG_FAN_MAX(ix) (0xb4 + (ix)) /* only for fan[4-5] */ 110 111/* PWMs numbered 0-2, 4-5 (ix) */ 112#define DME1737_REG_PWM(ix) ((ix) < 3 ? 0x30 + (ix) \ 113 : 0xa1 + (ix)) 114#define DME1737_REG_PWM_CONFIG(ix) (0x5c + (ix)) /* only for pwm[0-2] */ 115#define DME1737_REG_PWM_MIN(ix) (0x64 + (ix)) /* only for pwm[0-2] */ 116#define DME1737_REG_PWM_FREQ(ix) ((ix) < 3 ? 0x5f + (ix) \ 117 : 0xa3 + (ix)) 118/* The layout of the ramp rate registers is different from the other pwm 119 * registers. The bits for the 3 PWMs are stored in 2 registers: 120 * PWM_RR(0) = [OFF3, OFF2, OFF1, RES, RR1E, RR1-2, RR1-1, RR1-0] 121 * PWM_RR(1) = [RR2E, RR2-2, RR2-1, RR2-0, RR3E, RR3-2, RR3-1, RR3-0] */ 122#define DME1737_REG_PWM_RR(ix) (0x62 + (ix)) /* only for pwm[0-2] */ 123 124/* Thermal zones 0-2 */ 125#define DME1737_REG_ZONE_LOW(ix) (0x67 + (ix)) 126#define DME1737_REG_ZONE_ABS(ix) (0x6a + (ix)) 127/* The layout of the hysteresis registers is different from the other zone 128 * registers. The bits for the 3 zones are stored in 2 registers: 129 * ZONE_HYST(0) = [H1-3, H1-2, H1-1, H1-0, H2-3, H2-2, H2-1, H2-0] 130 * ZONE_HYST(1) = [H3-3, H3-2, H3-1, H3-0, RES, RES, RES, RES] */ 131#define DME1737_REG_ZONE_HYST(ix) (0x6d + (ix)) 132 133/* Alarm registers and bit mapping 134 * The 3 8-bit alarm registers will be concatenated to a single 32-bit 135 * alarm value [0, ALARM3, ALARM2, ALARM1]. */ 136#define DME1737_REG_ALARM1 0x41 137#define DME1737_REG_ALARM2 0x42 138#define DME1737_REG_ALARM3 0x83 139static const u8 DME1737_BIT_ALARM_IN[] = {0, 1, 2, 3, 8, 16, 17}; 140static const u8 DME1737_BIT_ALARM_TEMP[] = {4, 5, 6}; 141static const u8 DME1737_BIT_ALARM_FAN[] = {10, 11, 12, 13, 22, 23}; 142 143/* Miscellaneous registers */ 144#define DME1737_REG_DEVICE 0x3d 145#define DME1737_REG_COMPANY 0x3e 146#define DME1737_REG_VERSTEP 0x3f 147#define DME1737_REG_CONFIG 0x40 148#define DME1737_REG_CONFIG2 0x7f 149#define DME1737_REG_VID 0x43 150#define DME1737_REG_TACH_PWM 0x81 151 152/* --------------------------------------------------------------------- 153 * Misc defines 154 * --------------------------------------------------------------------- */ 155 156/* Chip identification */ 157#define DME1737_COMPANY_SMSC 0x5c 158#define DME1737_VERSTEP 0x88 159#define DME1737_VERSTEP_MASK 0xf8 160#define SCH311X_DEVICE 0x8c 161 162/* Length of ISA address segment */ 163#define DME1737_EXTENT 2 164 165/* --------------------------------------------------------------------- 166 * Data structures and manipulation thereof 167 * --------------------------------------------------------------------- */ 168 169/* For ISA chips, we abuse the i2c_client addr and name fields. We also use 170 the driver field to differentiate between I2C and ISA chips. */ 171struct dme1737_data { 172 struct i2c_client client; 173 struct device *hwmon_dev; 174 175 struct mutex update_lock; 176 int valid; /* !=0 if following fields are valid */ 177 unsigned long last_update; /* in jiffies */ 178 unsigned long last_vbat; /* in jiffies */ 179 180 u8 vid; 181 u8 pwm_rr_en; 182 u8 has_pwm; 183 u8 has_fan; 184 185 /* Register values */ 186 u16 in[7]; 187 u8 in_min[7]; 188 u8 in_max[7]; 189 s16 temp[3]; 190 s8 temp_min[3]; 191 s8 temp_max[3]; 192 s8 temp_offset[3]; 193 u8 config; 194 u8 config2; 195 u8 vrm; 196 u16 fan[6]; 197 u16 fan_min[6]; 198 u8 fan_max[2]; 199 u8 fan_opt[6]; 200 u8 pwm[6]; 201 u8 pwm_min[3]; 202 u8 pwm_config[3]; 203 u8 pwm_acz[3]; 204 u8 pwm_freq[6]; 205 u8 pwm_rr[2]; 206 u8 zone_low[3]; 207 u8 zone_abs[3]; 208 u8 zone_hyst[2]; 209 u32 alarms; 210}; 211 212/* Nominal voltage values */ 213static const int IN_NOMINAL[] = {5000, 2250, 3300, 5000, 12000, 3300, 3300}; 214 215/* Voltage input 216 * Voltage inputs have 16 bits resolution, limit values have 8 bits 217 * resolution. */ 218static inline int IN_FROM_REG(int reg, int ix, int res) 219{ 220 return (reg * IN_NOMINAL[ix] + (3 << (res - 3))) / (3 << (res - 2)); 221} 222 223static inline int IN_TO_REG(int val, int ix) 224{ 225 return SENSORS_LIMIT((val * 192 + IN_NOMINAL[ix] / 2) / 226 IN_NOMINAL[ix], 0, 255); 227} 228 229/* Temperature input 230 * The register values represent temperatures in 2's complement notation from 231 * -127 degrees C to +127 degrees C. Temp inputs have 16 bits resolution, limit 232 * values have 8 bits resolution. */ 233static inline int TEMP_FROM_REG(int reg, int res) 234{ 235 return (reg * 1000) >> (res - 8); 236} 237 238static inline int TEMP_TO_REG(int val) 239{ 240 return SENSORS_LIMIT((val < 0 ? val - 500 : val + 500) / 1000, 241 -128, 127); 242} 243 244/* Temperature range */ 245static const int TEMP_RANGE[] = {2000, 2500, 3333, 4000, 5000, 6666, 8000, 246 10000, 13333, 16000, 20000, 26666, 32000, 247 40000, 53333, 80000}; 248 249static inline int TEMP_RANGE_FROM_REG(int reg) 250{ 251 return TEMP_RANGE[(reg >> 4) & 0x0f]; 252} 253 254static int TEMP_RANGE_TO_REG(int val, int reg) 255{ 256 int i; 257 258 for (i = 15; i > 0; i--) { 259 if (val > (TEMP_RANGE[i] + TEMP_RANGE[i - 1] + 1) / 2) { 260 break; 261 } 262 } 263 264 return (reg & 0x0f) | (i << 4); 265} 266 267/* Temperature hysteresis 268 * Register layout: 269 * reg[0] = [H1-3, H1-2, H1-1, H1-0, H2-3, H2-2, H2-1, H2-0] 270 * reg[1] = [H3-3, H3-2, H3-1, H3-0, xxxx, xxxx, xxxx, xxxx] */ 271static inline int TEMP_HYST_FROM_REG(int reg, int ix) 272{ 273 return (((ix == 1) ? reg : reg >> 4) & 0x0f) * 1000; 274} 275 276static inline int TEMP_HYST_TO_REG(int val, int ix, int reg) 277{ 278 int hyst = SENSORS_LIMIT((val + 500) / 1000, 0, 15); 279 280 return (ix == 1) ? (reg & 0xf0) | hyst : (reg & 0x0f) | (hyst << 4); 281} 282 283/* Fan input RPM */ 284static inline int FAN_FROM_REG(int reg, int tpc) 285{ 286 if (tpc) { 287 return tpc * reg; 288 } else { 289 return (reg == 0 || reg == 0xffff) ? 0 : 90000 * 60 / reg; 290 } 291} 292 293static inline int FAN_TO_REG(int val, int tpc) 294{ 295 if (tpc) { 296 return SENSORS_LIMIT(val / tpc, 0, 0xffff); 297 } else { 298 return (val <= 0) ? 0xffff : 299 SENSORS_LIMIT(90000 * 60 / val, 0, 0xfffe); 300 } 301} 302 303/* Fan TPC (tach pulse count) 304 * Converts a register value to a TPC multiplier or returns 0 if the tachometer 305 * is configured in legacy (non-tpc) mode */ 306static inline int FAN_TPC_FROM_REG(int reg) 307{ 308 return (reg & 0x20) ? 0 : 60 >> (reg & 0x03); 309} 310 311/* Fan type 312 * The type of a fan is expressed in number of pulses-per-revolution that it 313 * emits */ 314static inline int FAN_TYPE_FROM_REG(int reg) 315{ 316 int edge = (reg >> 1) & 0x03; 317 318 return (edge > 0) ? 1 << (edge - 1) : 0; 319} 320 321static inline int FAN_TYPE_TO_REG(int val, int reg) 322{ 323 int edge = (val == 4) ? 3 : val; 324 325 return (reg & 0xf9) | (edge << 1); 326} 327 328/* Fan max RPM */ 329static const int FAN_MAX[] = {0x54, 0x38, 0x2a, 0x21, 0x1c, 0x18, 0x15, 0x12, 330 0x11, 0x0f, 0x0e}; 331 332static int FAN_MAX_FROM_REG(int reg) 333{ 334 int i; 335 336 for (i = 10; i > 0; i--) { 337 if (reg == FAN_MAX[i]) { 338 break; 339 } 340 } 341 342 return 1000 + i * 500; 343} 344 345static int FAN_MAX_TO_REG(int val) 346{ 347 int i; 348 349 for (i = 10; i > 0; i--) { 350 if (val > (1000 + (i - 1) * 500)) { 351 break; 352 } 353 } 354 355 return FAN_MAX[i]; 356} 357 358/* PWM enable 359 * Register to enable mapping: 360 * 000: 2 fan on zone 1 auto 361 * 001: 2 fan on zone 2 auto 362 * 010: 2 fan on zone 3 auto 363 * 011: 0 fan full on 364 * 100: -1 fan disabled 365 * 101: 2 fan on hottest of zones 2,3 auto 366 * 110: 2 fan on hottest of zones 1,2,3 auto 367 * 111: 1 fan in manual mode */ 368static inline int PWM_EN_FROM_REG(int reg) 369{ 370 static const int en[] = {2, 2, 2, 0, -1, 2, 2, 1}; 371 372 return en[(reg >> 5) & 0x07]; 373} 374 375static inline int PWM_EN_TO_REG(int val, int reg) 376{ 377 int en = (val == 1) ? 7 : 3; 378 379 return (reg & 0x1f) | ((en & 0x07) << 5); 380} 381 382/* PWM auto channels zone 383 * Register to auto channels zone mapping (ACZ is a bitfield with bit x 384 * corresponding to zone x+1): 385 * 000: 001 fan on zone 1 auto 386 * 001: 010 fan on zone 2 auto 387 * 010: 100 fan on zone 3 auto 388 * 011: 000 fan full on 389 * 100: 000 fan disabled 390 * 101: 110 fan on hottest of zones 2,3 auto 391 * 110: 111 fan on hottest of zones 1,2,3 auto 392 * 111: 000 fan in manual mode */ 393static inline int PWM_ACZ_FROM_REG(int reg) 394{ 395 static const int acz[] = {1, 2, 4, 0, 0, 6, 7, 0}; 396 397 return acz[(reg >> 5) & 0x07]; 398} 399 400static inline int PWM_ACZ_TO_REG(int val, int reg) 401{ 402 int acz = (val == 4) ? 2 : val - 1; 403 404 return (reg & 0x1f) | ((acz & 0x07) << 5); 405} 406 407/* PWM frequency */ 408static const int PWM_FREQ[] = {11, 15, 22, 29, 35, 44, 59, 88, 409 15000, 20000, 30000, 25000, 0, 0, 0, 0}; 410 411static inline int PWM_FREQ_FROM_REG(int reg) 412{ 413 return PWM_FREQ[reg & 0x0f]; 414} 415 416static int PWM_FREQ_TO_REG(int val, int reg) 417{ 418 int i; 419 420 /* the first two cases are special - stupid chip design! */ 421 if (val > 27500) { 422 i = 10; 423 } else if (val > 22500) { 424 i = 11; 425 } else { 426 for (i = 9; i > 0; i--) { 427 if (val > (PWM_FREQ[i] + PWM_FREQ[i - 1] + 1) / 2) { 428 break; 429 } 430 } 431 } 432 433 return (reg & 0xf0) | i; 434} 435 436/* PWM ramp rate 437 * Register layout: 438 * reg[0] = [OFF3, OFF2, OFF1, RES, RR1-E, RR1-2, RR1-1, RR1-0] 439 * reg[1] = [RR2-E, RR2-2, RR2-1, RR2-0, RR3-E, RR3-2, RR3-1, RR3-0] */ 440static const u8 PWM_RR[] = {206, 104, 69, 41, 26, 18, 10, 5}; 441 442static inline int PWM_RR_FROM_REG(int reg, int ix) 443{ 444 int rr = (ix == 1) ? reg >> 4 : reg; 445 446 return (rr & 0x08) ? PWM_RR[rr & 0x07] : 0; 447} 448 449static int PWM_RR_TO_REG(int val, int ix, int reg) 450{ 451 int i; 452 453 for (i = 0; i < 7; i++) { 454 if (val > (PWM_RR[i] + PWM_RR[i + 1] + 1) / 2) { 455 break; 456 } 457 } 458 459 return (ix == 1) ? (reg & 0x8f) | (i << 4) : (reg & 0xf8) | i; 460} 461 462/* PWM ramp rate enable */ 463static inline int PWM_RR_EN_FROM_REG(int reg, int ix) 464{ 465 return PWM_RR_FROM_REG(reg, ix) ? 1 : 0; 466} 467 468static inline int PWM_RR_EN_TO_REG(int val, int ix, int reg) 469{ 470 int en = (ix == 1) ? 0x80 : 0x08; 471 472 return val ? reg | en : reg & ~en; 473} 474 475/* PWM min/off 476 * The PWM min/off bits are part of the PMW ramp rate register 0 (see above for 477 * the register layout). */ 478static inline int PWM_OFF_FROM_REG(int reg, int ix) 479{ 480 return (reg >> (ix + 5)) & 0x01; 481} 482 483static inline int PWM_OFF_TO_REG(int val, int ix, int reg) 484{ 485 return (reg & ~(1 << (ix + 5))) | ((val & 0x01) << (ix + 5)); 486} 487 488/* --------------------------------------------------------------------- 489 * Device I/O access 490 * 491 * ISA access is performed through an index/data register pair and needs to 492 * be protected by a mutex during runtime (not required for initialization). 493 * We use data->update_lock for this and need to ensure that we acquire it 494 * before calling dme1737_read or dme1737_write. 495 * --------------------------------------------------------------------- */ 496 497static u8 dme1737_read(struct i2c_client *client, u8 reg) 498{ 499 s32 val; 500 501 if (client->driver) { /* I2C device */ 502 val = i2c_smbus_read_byte_data(client, reg); 503 504 if (val < 0) { 505 dev_warn(&client->dev, "Read from register " 506 "0x%02x failed! Please report to the driver " 507 "maintainer.\n", reg); 508 } 509 } else { /* ISA device */ 510 outb(reg, client->addr); 511 val = inb(client->addr + 1); 512 } 513 514 return val; 515} 516 517static s32 dme1737_write(struct i2c_client *client, u8 reg, u8 val) 518{ 519 s32 res = 0; 520 521 if (client->driver) { /* I2C device */ 522 res = i2c_smbus_write_byte_data(client, reg, val); 523 524 if (res < 0) { 525 dev_warn(&client->dev, "Write to register " 526 "0x%02x failed! Please report to the driver " 527 "maintainer.\n", reg); 528 } 529 } else { /* ISA device */ 530 outb(reg, client->addr); 531 outb(val, client->addr + 1); 532 } 533 534 return res; 535} 536 537static struct dme1737_data *dme1737_update_device(struct device *dev) 538{ 539 struct dme1737_data *data = dev_get_drvdata(dev); 540 struct i2c_client *client = &data->client; 541 int ix; 542 u8 lsb[5]; 543 544 mutex_lock(&data->update_lock); 545 546 /* Enable a Vbat monitoring cycle every 10 mins */ 547 if (time_after(jiffies, data->last_vbat + 600 * HZ) || !data->valid) { 548 dme1737_write(client, DME1737_REG_CONFIG, dme1737_read(client, 549 DME1737_REG_CONFIG) | 0x10); 550 data->last_vbat = jiffies; 551 } 552 553 /* Sample register contents every 1 sec */ 554 if (time_after(jiffies, data->last_update + HZ) || !data->valid) { 555 data->vid = dme1737_read(client, DME1737_REG_VID) & 0x3f; 556 557 /* In (voltage) registers */ 558 for (ix = 0; ix < ARRAY_SIZE(data->in); ix++) { 559 /* Voltage inputs are stored as 16 bit values even 560 * though they have only 12 bits resolution. This is 561 * to make it consistent with the temp inputs. */ 562 data->in[ix] = dme1737_read(client, 563 DME1737_REG_IN(ix)) << 8; 564 data->in_min[ix] = dme1737_read(client, 565 DME1737_REG_IN_MIN(ix)); 566 data->in_max[ix] = dme1737_read(client, 567 DME1737_REG_IN_MAX(ix)); 568 } 569 570 /* Temp registers */ 571 for (ix = 0; ix < ARRAY_SIZE(data->temp); ix++) { 572 /* Temp inputs are stored as 16 bit values even 573 * though they have only 12 bits resolution. This is 574 * to take advantage of implicit conversions between 575 * register values (2's complement) and temp values 576 * (signed decimal). */ 577 data->temp[ix] = dme1737_read(client, 578 DME1737_REG_TEMP(ix)) << 8; 579 data->temp_min[ix] = dme1737_read(client, 580 DME1737_REG_TEMP_MIN(ix)); 581 data->temp_max[ix] = dme1737_read(client, 582 DME1737_REG_TEMP_MAX(ix)); 583 data->temp_offset[ix] = dme1737_read(client, 584 DME1737_REG_TEMP_OFFSET(ix)); 585 } 586 587 /* In and temp LSB registers 588 * The LSBs are latched when the MSBs are read, so the order in 589 * which the registers are read (MSB first, then LSB) is 590 * important! */ 591 for (ix = 0; ix < ARRAY_SIZE(lsb); ix++) { 592 lsb[ix] = dme1737_read(client, 593 DME1737_REG_IN_TEMP_LSB(ix)); 594 } 595 for (ix = 0; ix < ARRAY_SIZE(data->in); ix++) { 596 data->in[ix] |= (lsb[DME1737_REG_IN_LSB[ix]] << 597 DME1737_REG_IN_LSB_SHL[ix]) & 0xf0; 598 } 599 for (ix = 0; ix < ARRAY_SIZE(data->temp); ix++) { 600 data->temp[ix] |= (lsb[DME1737_REG_TEMP_LSB[ix]] << 601 DME1737_REG_TEMP_LSB_SHL[ix]) & 0xf0; 602 } 603 604 /* Fan registers */ 605 for (ix = 0; ix < ARRAY_SIZE(data->fan); ix++) { 606 /* Skip reading registers if optional fans are not 607 * present */ 608 if (!(data->has_fan & (1 << ix))) { 609 continue; 610 } 611 data->fan[ix] = dme1737_read(client, 612 DME1737_REG_FAN(ix)); 613 data->fan[ix] |= dme1737_read(client, 614 DME1737_REG_FAN(ix) + 1) << 8; 615 data->fan_min[ix] = dme1737_read(client, 616 DME1737_REG_FAN_MIN(ix)); 617 data->fan_min[ix] |= dme1737_read(client, 618 DME1737_REG_FAN_MIN(ix) + 1) << 8; 619 data->fan_opt[ix] = dme1737_read(client, 620 DME1737_REG_FAN_OPT(ix)); 621 /* fan_max exists only for fan[5-6] */ 622 if (ix > 3) { 623 data->fan_max[ix - 4] = dme1737_read(client, 624 DME1737_REG_FAN_MAX(ix)); 625 } 626 } 627 628 /* PWM registers */ 629 for (ix = 0; ix < ARRAY_SIZE(data->pwm); ix++) { 630 /* Skip reading registers if optional PWMs are not 631 * present */ 632 if (!(data->has_pwm & (1 << ix))) { 633 continue; 634 } 635 data->pwm[ix] = dme1737_read(client, 636 DME1737_REG_PWM(ix)); 637 data->pwm_freq[ix] = dme1737_read(client, 638 DME1737_REG_PWM_FREQ(ix)); 639 /* pwm_config and pwm_min exist only for pwm[1-3] */ 640 if (ix < 3) { 641 data->pwm_config[ix] = dme1737_read(client, 642 DME1737_REG_PWM_CONFIG(ix)); 643 data->pwm_min[ix] = dme1737_read(client, 644 DME1737_REG_PWM_MIN(ix)); 645 } 646 } 647 for (ix = 0; ix < ARRAY_SIZE(data->pwm_rr); ix++) { 648 data->pwm_rr[ix] = dme1737_read(client, 649 DME1737_REG_PWM_RR(ix)); 650 } 651 652 /* Thermal zone registers */ 653 for (ix = 0; ix < ARRAY_SIZE(data->zone_low); ix++) { 654 data->zone_low[ix] = dme1737_read(client, 655 DME1737_REG_ZONE_LOW(ix)); 656 data->zone_abs[ix] = dme1737_read(client, 657 DME1737_REG_ZONE_ABS(ix)); 658 } 659 for (ix = 0; ix < ARRAY_SIZE(data->zone_hyst); ix++) { 660 data->zone_hyst[ix] = dme1737_read(client, 661 DME1737_REG_ZONE_HYST(ix)); 662 } 663 664 /* Alarm registers */ 665 data->alarms = dme1737_read(client, 666 DME1737_REG_ALARM1); 667 /* Bit 7 tells us if the other alarm registers are non-zero and 668 * therefore also need to be read */ 669 if (data->alarms & 0x80) { 670 data->alarms |= dme1737_read(client, 671 DME1737_REG_ALARM2) << 8; 672 data->alarms |= dme1737_read(client, 673 DME1737_REG_ALARM3) << 16; 674 } 675 676 /* The ISA chips require explicit clearing of alarm bits. 677 * Don't worry, an alarm will come back if the condition 678 * that causes it still exists */ 679 if (!client->driver) { 680 if (data->alarms & 0xff0000) { 681 dme1737_write(client, DME1737_REG_ALARM3, 682 0xff); 683 } 684 if (data->alarms & 0xff00) { 685 dme1737_write(client, DME1737_REG_ALARM2, 686 0xff); 687 } 688 if (data->alarms & 0xff) { 689 dme1737_write(client, DME1737_REG_ALARM1, 690 0xff); 691 } 692 } 693 694 data->last_update = jiffies; 695 data->valid = 1; 696 } 697 698 mutex_unlock(&data->update_lock); 699 700 return data; 701} 702 703/* --------------------------------------------------------------------- 704 * Voltage sysfs attributes 705 * ix = [0-5] 706 * --------------------------------------------------------------------- */ 707 708#define SYS_IN_INPUT 0 709#define SYS_IN_MIN 1 710#define SYS_IN_MAX 2 711#define SYS_IN_ALARM 3 712 713static ssize_t show_in(struct device *dev, struct device_attribute *attr, 714 char *buf) 715{ 716 struct dme1737_data *data = dme1737_update_device(dev); 717 struct sensor_device_attribute_2 718 *sensor_attr_2 = to_sensor_dev_attr_2(attr); 719 int ix = sensor_attr_2->index; 720 int fn = sensor_attr_2->nr; 721 int res; 722 723 switch (fn) { 724 case SYS_IN_INPUT: 725 res = IN_FROM_REG(data->in[ix], ix, 16); 726 break; 727 case SYS_IN_MIN: 728 res = IN_FROM_REG(data->in_min[ix], ix, 8); 729 break; 730 case SYS_IN_MAX: 731 res = IN_FROM_REG(data->in_max[ix], ix, 8); 732 break; 733 case SYS_IN_ALARM: 734 res = (data->alarms >> DME1737_BIT_ALARM_IN[ix]) & 0x01; 735 break; 736 default: 737 res = 0; 738 dev_dbg(dev, "Unknown function %d.\n", fn); 739 } 740 741 return sprintf(buf, "%d\n", res); 742} 743 744static ssize_t set_in(struct device *dev, struct device_attribute *attr, 745 const char *buf, size_t count) 746{ 747 struct dme1737_data *data = dev_get_drvdata(dev); 748 struct i2c_client *client = &data->client; 749 struct sensor_device_attribute_2 750 *sensor_attr_2 = to_sensor_dev_attr_2(attr); 751 int ix = sensor_attr_2->index; 752 int fn = sensor_attr_2->nr; 753 long val = simple_strtol(buf, NULL, 10); 754 755 mutex_lock(&data->update_lock); 756 switch (fn) { 757 case SYS_IN_MIN: 758 data->in_min[ix] = IN_TO_REG(val, ix); 759 dme1737_write(client, DME1737_REG_IN_MIN(ix), 760 data->in_min[ix]); 761 break; 762 case SYS_IN_MAX: 763 data->in_max[ix] = IN_TO_REG(val, ix); 764 dme1737_write(client, DME1737_REG_IN_MAX(ix), 765 data->in_max[ix]); 766 break; 767 default: 768 dev_dbg(dev, "Unknown function %d.\n", fn); 769 } 770 mutex_unlock(&data->update_lock); 771 772 return count; 773} 774 775/* --------------------------------------------------------------------- 776 * Temperature sysfs attributes 777 * ix = [0-2] 778 * --------------------------------------------------------------------- */ 779 780#define SYS_TEMP_INPUT 0 781#define SYS_TEMP_MIN 1 782#define SYS_TEMP_MAX 2 783#define SYS_TEMP_OFFSET 3 784#define SYS_TEMP_ALARM 4 785#define SYS_TEMP_FAULT 5 786 787static ssize_t show_temp(struct device *dev, struct device_attribute *attr, 788 char *buf) 789{ 790 struct dme1737_data *data = dme1737_update_device(dev); 791 struct sensor_device_attribute_2 792 *sensor_attr_2 = to_sensor_dev_attr_2(attr); 793 int ix = sensor_attr_2->index; 794 int fn = sensor_attr_2->nr; 795 int res; 796 797 switch (fn) { 798 case SYS_TEMP_INPUT: 799 res = TEMP_FROM_REG(data->temp[ix], 16); 800 break; 801 case SYS_TEMP_MIN: 802 res = TEMP_FROM_REG(data->temp_min[ix], 8); 803 break; 804 case SYS_TEMP_MAX: 805 res = TEMP_FROM_REG(data->temp_max[ix], 8); 806 break; 807 case SYS_TEMP_OFFSET: 808 res = TEMP_FROM_REG(data->temp_offset[ix], 8); 809 break; 810 case SYS_TEMP_ALARM: 811 res = (data->alarms >> DME1737_BIT_ALARM_TEMP[ix]) & 0x01; 812 break; 813 case SYS_TEMP_FAULT: 814 res = (((u16)data->temp[ix] & 0xff00) == 0x8000); 815 break; 816 default: 817 res = 0; 818 dev_dbg(dev, "Unknown function %d.\n", fn); 819 } 820 821 return sprintf(buf, "%d\n", res); 822} 823 824static ssize_t set_temp(struct device *dev, struct device_attribute *attr, 825 const char *buf, size_t count) 826{ 827 struct dme1737_data *data = dev_get_drvdata(dev); 828 struct i2c_client *client = &data->client; 829 struct sensor_device_attribute_2 830 *sensor_attr_2 = to_sensor_dev_attr_2(attr); 831 int ix = sensor_attr_2->index; 832 int fn = sensor_attr_2->nr; 833 long val = simple_strtol(buf, NULL, 10); 834 835 mutex_lock(&data->update_lock); 836 switch (fn) { 837 case SYS_TEMP_MIN: 838 data->temp_min[ix] = TEMP_TO_REG(val); 839 dme1737_write(client, DME1737_REG_TEMP_MIN(ix), 840 data->temp_min[ix]); 841 break; 842 case SYS_TEMP_MAX: 843 data->temp_max[ix] = TEMP_TO_REG(val); 844 dme1737_write(client, DME1737_REG_TEMP_MAX(ix), 845 data->temp_max[ix]); 846 break; 847 case SYS_TEMP_OFFSET: 848 data->temp_offset[ix] = TEMP_TO_REG(val); 849 dme1737_write(client, DME1737_REG_TEMP_OFFSET(ix), 850 data->temp_offset[ix]); 851 break; 852 default: 853 dev_dbg(dev, "Unknown function %d.\n", fn); 854 } 855 mutex_unlock(&data->update_lock); 856 857 return count; 858} 859 860/* --------------------------------------------------------------------- 861 * Zone sysfs attributes 862 * ix = [0-2] 863 * --------------------------------------------------------------------- */ 864 865#define SYS_ZONE_AUTO_CHANNELS_TEMP 0 866#define SYS_ZONE_AUTO_POINT1_TEMP_HYST 1 867#define SYS_ZONE_AUTO_POINT1_TEMP 2 868#define SYS_ZONE_AUTO_POINT2_TEMP 3 869#define SYS_ZONE_AUTO_POINT3_TEMP 4 870 871static ssize_t show_zone(struct device *dev, struct device_attribute *attr, 872 char *buf) 873{ 874 struct dme1737_data *data = dme1737_update_device(dev); 875 struct sensor_device_attribute_2 876 *sensor_attr_2 = to_sensor_dev_attr_2(attr); 877 int ix = sensor_attr_2->index; 878 int fn = sensor_attr_2->nr; 879 int res; 880 881 switch (fn) { 882 case SYS_ZONE_AUTO_CHANNELS_TEMP: 883 /* check config2 for non-standard temp-to-zone mapping */ 884 if ((ix == 1) && (data->config2 & 0x02)) { 885 res = 4; 886 } else { 887 res = 1 << ix; 888 } 889 break; 890 case SYS_ZONE_AUTO_POINT1_TEMP_HYST: 891 res = TEMP_FROM_REG(data->zone_low[ix], 8) - 892 TEMP_HYST_FROM_REG(data->zone_hyst[ix == 2], ix); 893 break; 894 case SYS_ZONE_AUTO_POINT1_TEMP: 895 res = TEMP_FROM_REG(data->zone_low[ix], 8); 896 break; 897 case SYS_ZONE_AUTO_POINT2_TEMP: 898 /* pwm_freq holds the temp range bits in the upper nibble */ 899 res = TEMP_FROM_REG(data->zone_low[ix], 8) + 900 TEMP_RANGE_FROM_REG(data->pwm_freq[ix]); 901 break; 902 case SYS_ZONE_AUTO_POINT3_TEMP: 903 res = TEMP_FROM_REG(data->zone_abs[ix], 8); 904 break; 905 default: 906 res = 0; 907 dev_dbg(dev, "Unknown function %d.\n", fn); 908 } 909 910 return sprintf(buf, "%d\n", res); 911} 912 913static ssize_t set_zone(struct device *dev, struct device_attribute *attr, 914 const char *buf, size_t count) 915{ 916 struct dme1737_data *data = dev_get_drvdata(dev); 917 struct i2c_client *client = &data->client; 918 struct sensor_device_attribute_2 919 *sensor_attr_2 = to_sensor_dev_attr_2(attr); 920 int ix = sensor_attr_2->index; 921 int fn = sensor_attr_2->nr; 922 long val = simple_strtol(buf, NULL, 10); 923 924 mutex_lock(&data->update_lock); 925 switch (fn) { 926 case SYS_ZONE_AUTO_POINT1_TEMP_HYST: 927 /* Refresh the cache */ 928 data->zone_low[ix] = dme1737_read(client, 929 DME1737_REG_ZONE_LOW(ix)); 930 /* Modify the temp hyst value */ 931 data->zone_hyst[ix == 2] = TEMP_HYST_TO_REG( 932 TEMP_FROM_REG(data->zone_low[ix], 8) - 933 val, ix, dme1737_read(client, 934 DME1737_REG_ZONE_HYST(ix == 2))); 935 dme1737_write(client, DME1737_REG_ZONE_HYST(ix == 2), 936 data->zone_hyst[ix == 2]); 937 break; 938 case SYS_ZONE_AUTO_POINT1_TEMP: 939 data->zone_low[ix] = TEMP_TO_REG(val); 940 dme1737_write(client, DME1737_REG_ZONE_LOW(ix), 941 data->zone_low[ix]); 942 break; 943 case SYS_ZONE_AUTO_POINT2_TEMP: 944 /* Refresh the cache */ 945 data->zone_low[ix] = dme1737_read(client, 946 DME1737_REG_ZONE_LOW(ix)); 947 /* Modify the temp range value (which is stored in the upper 948 * nibble of the pwm_freq register) */ 949 data->pwm_freq[ix] = TEMP_RANGE_TO_REG(val - 950 TEMP_FROM_REG(data->zone_low[ix], 8), 951 dme1737_read(client, 952 DME1737_REG_PWM_FREQ(ix))); 953 dme1737_write(client, DME1737_REG_PWM_FREQ(ix), 954 data->pwm_freq[ix]); 955 break; 956 case SYS_ZONE_AUTO_POINT3_TEMP: 957 data->zone_abs[ix] = TEMP_TO_REG(val); 958 dme1737_write(client, DME1737_REG_ZONE_ABS(ix), 959 data->zone_abs[ix]); 960 break; 961 default: 962 dev_dbg(dev, "Unknown function %d.\n", fn); 963 } 964 mutex_unlock(&data->update_lock); 965 966 return count; 967} 968 969/* --------------------------------------------------------------------- 970 * Fan sysfs attributes 971 * ix = [0-5] 972 * --------------------------------------------------------------------- */ 973 974#define SYS_FAN_INPUT 0 975#define SYS_FAN_MIN 1 976#define SYS_FAN_MAX 2 977#define SYS_FAN_ALARM 3 978#define SYS_FAN_TYPE 4 979 980static ssize_t show_fan(struct device *dev, struct device_attribute *attr, 981 char *buf) 982{ 983 struct dme1737_data *data = dme1737_update_device(dev); 984 struct sensor_device_attribute_2 985 *sensor_attr_2 = to_sensor_dev_attr_2(attr); 986 int ix = sensor_attr_2->index; 987 int fn = sensor_attr_2->nr; 988 int res; 989 990 switch (fn) { 991 case SYS_FAN_INPUT: 992 res = FAN_FROM_REG(data->fan[ix], 993 ix < 4 ? 0 : 994 FAN_TPC_FROM_REG(data->fan_opt[ix])); 995 break; 996 case SYS_FAN_MIN: 997 res = FAN_FROM_REG(data->fan_min[ix], 998 ix < 4 ? 0 : 999 FAN_TPC_FROM_REG(data->fan_opt[ix])); 1000 break; 1001 case SYS_FAN_MAX: 1002 /* only valid for fan[5-6] */ 1003 res = FAN_MAX_FROM_REG(data->fan_max[ix - 4]); 1004 break; 1005 case SYS_FAN_ALARM: 1006 res = (data->alarms >> DME1737_BIT_ALARM_FAN[ix]) & 0x01; 1007 break; 1008 case SYS_FAN_TYPE: 1009 /* only valid for fan[1-4] */ 1010 res = FAN_TYPE_FROM_REG(data->fan_opt[ix]); 1011 break; 1012 default: 1013 res = 0; 1014 dev_dbg(dev, "Unknown function %d.\n", fn); 1015 } 1016 1017 return sprintf(buf, "%d\n", res); 1018} 1019 1020static ssize_t set_fan(struct device *dev, struct device_attribute *attr, 1021 const char *buf, size_t count) 1022{ 1023 struct dme1737_data *data = dev_get_drvdata(dev); 1024 struct i2c_client *client = &data->client; 1025 struct sensor_device_attribute_2 1026 *sensor_attr_2 = to_sensor_dev_attr_2(attr); 1027 int ix = sensor_attr_2->index; 1028 int fn = sensor_attr_2->nr; 1029 long val = simple_strtol(buf, NULL, 10); 1030 1031 mutex_lock(&data->update_lock); 1032 switch (fn) { 1033 case SYS_FAN_MIN: 1034 if (ix < 4) { 1035 data->fan_min[ix] = FAN_TO_REG(val, 0); 1036 } else { 1037 /* Refresh the cache */ 1038 data->fan_opt[ix] = dme1737_read(client, 1039 DME1737_REG_FAN_OPT(ix)); 1040 /* Modify the fan min value */ 1041 data->fan_min[ix] = FAN_TO_REG(val, 1042 FAN_TPC_FROM_REG(data->fan_opt[ix])); 1043 } 1044 dme1737_write(client, DME1737_REG_FAN_MIN(ix), 1045 data->fan_min[ix] & 0xff); 1046 dme1737_write(client, DME1737_REG_FAN_MIN(ix) + 1, 1047 data->fan_min[ix] >> 8); 1048 break; 1049 case SYS_FAN_MAX: 1050 /* Only valid for fan[5-6] */ 1051 data->fan_max[ix - 4] = FAN_MAX_TO_REG(val); 1052 dme1737_write(client, DME1737_REG_FAN_MAX(ix), 1053 data->fan_max[ix - 4]); 1054 break; 1055 case SYS_FAN_TYPE: 1056 /* Only valid for fan[1-4] */ 1057 if (!(val == 1 || val == 2 || val == 4)) { 1058 count = -EINVAL; 1059 dev_warn(dev, "Fan type value %ld not " 1060 "supported. Choose one of 1, 2, or 4.\n", 1061 val); 1062 goto exit; 1063 } 1064 data->fan_opt[ix] = FAN_TYPE_TO_REG(val, dme1737_read(client, 1065 DME1737_REG_FAN_OPT(ix))); 1066 dme1737_write(client, DME1737_REG_FAN_OPT(ix), 1067 data->fan_opt[ix]); 1068 break; 1069 default: 1070 dev_dbg(dev, "Unknown function %d.\n", fn); 1071 } 1072exit: 1073 mutex_unlock(&data->update_lock); 1074 1075 return count; 1076} 1077 1078/* --------------------------------------------------------------------- 1079 * PWM sysfs attributes 1080 * ix = [0-4] 1081 * --------------------------------------------------------------------- */ 1082 1083#define SYS_PWM 0 1084#define SYS_PWM_FREQ 1 1085#define SYS_PWM_ENABLE 2 1086#define SYS_PWM_RAMP_RATE 3 1087#define SYS_PWM_AUTO_CHANNELS_ZONE 4 1088#define SYS_PWM_AUTO_PWM_MIN 5 1089#define SYS_PWM_AUTO_POINT1_PWM 6 1090#define SYS_PWM_AUTO_POINT2_PWM 7 1091 1092static ssize_t show_pwm(struct device *dev, struct device_attribute *attr, 1093 char *buf) 1094{ 1095 struct dme1737_data *data = dme1737_update_device(dev); 1096 struct sensor_device_attribute_2 1097 *sensor_attr_2 = to_sensor_dev_attr_2(attr); 1098 int ix = sensor_attr_2->index; 1099 int fn = sensor_attr_2->nr; 1100 int res; 1101 1102 switch (fn) { 1103 case SYS_PWM: 1104 if (PWM_EN_FROM_REG(data->pwm_config[ix]) == 0) { 1105 res = 255; 1106 } else { 1107 res = data->pwm[ix]; 1108 } 1109 break; 1110 case SYS_PWM_FREQ: 1111 res = PWM_FREQ_FROM_REG(data->pwm_freq[ix]); 1112 break; 1113 case SYS_PWM_ENABLE: 1114 if (ix > 3) { 1115 res = 1; /* pwm[5-6] hard-wired to manual mode */ 1116 } else { 1117 res = PWM_EN_FROM_REG(data->pwm_config[ix]); 1118 } 1119 break; 1120 case SYS_PWM_RAMP_RATE: 1121 /* Only valid for pwm[1-3] */ 1122 res = PWM_RR_FROM_REG(data->pwm_rr[ix > 0], ix); 1123 break; 1124 case SYS_PWM_AUTO_CHANNELS_ZONE: 1125 /* Only valid for pwm[1-3] */ 1126 if (PWM_EN_FROM_REG(data->pwm_config[ix]) == 2) { 1127 res = PWM_ACZ_FROM_REG(data->pwm_config[ix]); 1128 } else { 1129 res = data->pwm_acz[ix]; 1130 } 1131 break; 1132 case SYS_PWM_AUTO_PWM_MIN: 1133 /* Only valid for pwm[1-3] */ 1134 if (PWM_OFF_FROM_REG(data->pwm_rr[0], ix)) { 1135 res = data->pwm_min[ix]; 1136 } else { 1137 res = 0; 1138 } 1139 break; 1140 case SYS_PWM_AUTO_POINT1_PWM: 1141 /* Only valid for pwm[1-3] */ 1142 res = data->pwm_min[ix]; 1143 break; 1144 case SYS_PWM_AUTO_POINT2_PWM: 1145 /* Only valid for pwm[1-3] */ 1146 res = 255; /* hard-wired */ 1147 break; 1148 default: 1149 res = 0; 1150 dev_dbg(dev, "Unknown function %d.\n", fn); 1151 } 1152 1153 return sprintf(buf, "%d\n", res); 1154} 1155 1156static struct attribute *dme1737_attr_pwm[]; 1157static void dme1737_chmod_file(struct device*, struct attribute*, mode_t); 1158 1159static ssize_t set_pwm(struct device *dev, struct device_attribute *attr, 1160 const char *buf, size_t count) 1161{ 1162 struct dme1737_data *data = dev_get_drvdata(dev); 1163 struct i2c_client *client = &data->client; 1164 struct sensor_device_attribute_2 1165 *sensor_attr_2 = to_sensor_dev_attr_2(attr); 1166 int ix = sensor_attr_2->index; 1167 int fn = sensor_attr_2->nr; 1168 long val = simple_strtol(buf, NULL, 10); 1169 1170 mutex_lock(&data->update_lock); 1171 switch (fn) { 1172 case SYS_PWM: 1173 data->pwm[ix] = SENSORS_LIMIT(val, 0, 255); 1174 dme1737_write(client, DME1737_REG_PWM(ix), data->pwm[ix]); 1175 break; 1176 case SYS_PWM_FREQ: 1177 data->pwm_freq[ix] = PWM_FREQ_TO_REG(val, dme1737_read(client, 1178 DME1737_REG_PWM_FREQ(ix))); 1179 dme1737_write(client, DME1737_REG_PWM_FREQ(ix), 1180 data->pwm_freq[ix]); 1181 break; 1182 case SYS_PWM_ENABLE: 1183 /* Only valid for pwm[1-3] */ 1184 if (val < 0 || val > 2) { 1185 count = -EINVAL; 1186 dev_warn(dev, "PWM enable %ld not " 1187 "supported. Choose one of 0, 1, or 2.\n", 1188 val); 1189 goto exit; 1190 } 1191 /* Refresh the cache */ 1192 data->pwm_config[ix] = dme1737_read(client, 1193 DME1737_REG_PWM_CONFIG(ix)); 1194 if (val == PWM_EN_FROM_REG(data->pwm_config[ix])) { 1195 /* Bail out if no change */ 1196 goto exit; 1197 } 1198 /* Do some housekeeping if we are currently in auto mode */ 1199 if (PWM_EN_FROM_REG(data->pwm_config[ix]) == 2) { 1200 /* Save the current zone channel assignment */ 1201 data->pwm_acz[ix] = PWM_ACZ_FROM_REG( 1202 data->pwm_config[ix]); 1203 /* Save the current ramp rate state and disable it */ 1204 data->pwm_rr[ix > 0] = dme1737_read(client, 1205 DME1737_REG_PWM_RR(ix > 0)); 1206 data->pwm_rr_en &= ~(1 << ix); 1207 if (PWM_RR_EN_FROM_REG(data->pwm_rr[ix > 0], ix)) { 1208 data->pwm_rr_en |= (1 << ix); 1209 data->pwm_rr[ix > 0] = PWM_RR_EN_TO_REG(0, ix, 1210 data->pwm_rr[ix > 0]); 1211 dme1737_write(client, 1212 DME1737_REG_PWM_RR(ix > 0), 1213 data->pwm_rr[ix > 0]); 1214 } 1215 } 1216 /* Set the new PWM mode */ 1217 switch (val) { 1218 case 0: 1219 /* Change permissions of pwm[ix] to read-only */ 1220 dme1737_chmod_file(dev, dme1737_attr_pwm[ix], 1221 S_IRUGO); 1222 /* Turn fan fully on */ 1223 data->pwm_config[ix] = PWM_EN_TO_REG(0, 1224 data->pwm_config[ix]); 1225 dme1737_write(client, DME1737_REG_PWM_CONFIG(ix), 1226 data->pwm_config[ix]); 1227 break; 1228 case 1: 1229 /* Turn on manual mode */ 1230 data->pwm_config[ix] = PWM_EN_TO_REG(1, 1231 data->pwm_config[ix]); 1232 dme1737_write(client, DME1737_REG_PWM_CONFIG(ix), 1233 data->pwm_config[ix]); 1234 /* Change permissions of pwm[ix] to read-writeable */ 1235 dme1737_chmod_file(dev, dme1737_attr_pwm[ix], 1236 S_IRUGO | S_IWUSR); 1237 break; 1238 case 2: 1239 /* Change permissions of pwm[ix] to read-only */ 1240 dme1737_chmod_file(dev, dme1737_attr_pwm[ix], 1241 S_IRUGO); 1242 /* Turn on auto mode using the saved zone channel 1243 * assignment */ 1244 data->pwm_config[ix] = PWM_ACZ_TO_REG( 1245 data->pwm_acz[ix], 1246 data->pwm_config[ix]); 1247 dme1737_write(client, DME1737_REG_PWM_CONFIG(ix), 1248 data->pwm_config[ix]); 1249 /* Enable PWM ramp rate if previously enabled */ 1250 if (data->pwm_rr_en & (1 << ix)) { 1251 data->pwm_rr[ix > 0] = PWM_RR_EN_TO_REG(1, ix, 1252 dme1737_read(client, 1253 DME1737_REG_PWM_RR(ix > 0))); 1254 dme1737_write(client, 1255 DME1737_REG_PWM_RR(ix > 0), 1256 data->pwm_rr[ix > 0]); 1257 } 1258 break; 1259 } 1260 break; 1261 case SYS_PWM_RAMP_RATE: 1262 /* Only valid for pwm[1-3] */ 1263 /* Refresh the cache */ 1264 data->pwm_config[ix] = dme1737_read(client, 1265 DME1737_REG_PWM_CONFIG(ix)); 1266 data->pwm_rr[ix > 0] = dme1737_read(client, 1267 DME1737_REG_PWM_RR(ix > 0)); 1268 /* Set the ramp rate value */ 1269 if (val > 0) { 1270 data->pwm_rr[ix > 0] = PWM_RR_TO_REG(val, ix, 1271 data->pwm_rr[ix > 0]); 1272 } 1273 /* Enable/disable the feature only if the associated PWM 1274 * output is in automatic mode. */ 1275 if (PWM_EN_FROM_REG(data->pwm_config[ix]) == 2) { 1276 data->pwm_rr[ix > 0] = PWM_RR_EN_TO_REG(val > 0, ix, 1277 data->pwm_rr[ix > 0]); 1278 } 1279 dme1737_write(client, DME1737_REG_PWM_RR(ix > 0), 1280 data->pwm_rr[ix > 0]); 1281 break; 1282 case SYS_PWM_AUTO_CHANNELS_ZONE: 1283 /* Only valid for pwm[1-3] */ 1284 if (!(val == 1 || val == 2 || val == 4 || 1285 val == 6 || val == 7)) { 1286 count = -EINVAL; 1287 dev_warn(dev, "PWM auto channels zone %ld " 1288 "not supported. Choose one of 1, 2, 4, 6, " 1289 "or 7.\n", val); 1290 goto exit; 1291 } 1292 /* Refresh the cache */ 1293 data->pwm_config[ix] = dme1737_read(client, 1294 DME1737_REG_PWM_CONFIG(ix)); 1295 if (PWM_EN_FROM_REG(data->pwm_config[ix]) == 2) { 1296 /* PWM is already in auto mode so update the temp 1297 * channel assignment */ 1298 data->pwm_config[ix] = PWM_ACZ_TO_REG(val, 1299 data->pwm_config[ix]); 1300 dme1737_write(client, DME1737_REG_PWM_CONFIG(ix), 1301 data->pwm_config[ix]); 1302 } else { 1303 /* PWM is not in auto mode so we save the temp 1304 * channel assignment for later use */ 1305 data->pwm_acz[ix] = val; 1306 } 1307 break; 1308 case SYS_PWM_AUTO_PWM_MIN: 1309 /* Only valid for pwm[1-3] */ 1310 /* Refresh the cache */ 1311 data->pwm_min[ix] = dme1737_read(client, 1312 DME1737_REG_PWM_MIN(ix)); 1313 /* There are only 2 values supported for the auto_pwm_min 1314 * value: 0 or auto_point1_pwm. So if the temperature drops 1315 * below the auto_point1_temp_hyst value, the fan either turns 1316 * off or runs at auto_point1_pwm duty-cycle. */ 1317 if (val > ((data->pwm_min[ix] + 1) / 2)) { 1318 data->pwm_rr[0] = PWM_OFF_TO_REG(1, ix, 1319 dme1737_read(client, 1320 DME1737_REG_PWM_RR(0))); 1321 } else { 1322 data->pwm_rr[0] = PWM_OFF_TO_REG(0, ix, 1323 dme1737_read(client, 1324 DME1737_REG_PWM_RR(0))); 1325 } 1326 dme1737_write(client, DME1737_REG_PWM_RR(0), 1327 data->pwm_rr[0]); 1328 break; 1329 case SYS_PWM_AUTO_POINT1_PWM: 1330 /* Only valid for pwm[1-3] */ 1331 data->pwm_min[ix] = SENSORS_LIMIT(val, 0, 255); 1332 dme1737_write(client, DME1737_REG_PWM_MIN(ix), 1333 data->pwm_min[ix]); 1334 break; 1335 default: 1336 dev_dbg(dev, "Unknown function %d.\n", fn); 1337 } 1338exit: 1339 mutex_unlock(&data->update_lock); 1340 1341 return count; 1342} 1343 1344/* --------------------------------------------------------------------- 1345 * Miscellaneous sysfs attributes 1346 * --------------------------------------------------------------------- */ 1347 1348static ssize_t show_vrm(struct device *dev, struct device_attribute *attr, 1349 char *buf) 1350{ 1351 struct i2c_client *client = to_i2c_client(dev); 1352 struct dme1737_data *data = i2c_get_clientdata(client); 1353 1354 return sprintf(buf, "%d\n", data->vrm); 1355} 1356 1357static ssize_t set_vrm(struct device *dev, struct device_attribute *attr, 1358 const char *buf, size_t count) 1359{ 1360 struct dme1737_data *data = dev_get_drvdata(dev); 1361 long val = simple_strtol(buf, NULL, 10); 1362 1363 data->vrm = val; 1364 return count; 1365} 1366 1367static ssize_t show_vid(struct device *dev, struct device_attribute *attr, 1368 char *buf) 1369{ 1370 struct dme1737_data *data = dme1737_update_device(dev); 1371 1372 return sprintf(buf, "%d\n", vid_from_reg(data->vid, data->vrm)); 1373} 1374 1375static ssize_t show_name(struct device *dev, struct device_attribute *attr, 1376 char *buf) 1377{ 1378 struct dme1737_data *data = dev_get_drvdata(dev); 1379 1380 return sprintf(buf, "%s\n", data->client.name); 1381} 1382 1383/* --------------------------------------------------------------------- 1384 * Sysfs device attribute defines and structs 1385 * --------------------------------------------------------------------- */ 1386 1387/* Voltages 0-6 */ 1388 1389#define SENSOR_DEVICE_ATTR_IN(ix) \ 1390static SENSOR_DEVICE_ATTR_2(in##ix##_input, S_IRUGO, \ 1391 show_in, NULL, SYS_IN_INPUT, ix); \ 1392static SENSOR_DEVICE_ATTR_2(in##ix##_min, S_IRUGO | S_IWUSR, \ 1393 show_in, set_in, SYS_IN_MIN, ix); \ 1394static SENSOR_DEVICE_ATTR_2(in##ix##_max, S_IRUGO | S_IWUSR, \ 1395 show_in, set_in, SYS_IN_MAX, ix); \ 1396static SENSOR_DEVICE_ATTR_2(in##ix##_alarm, S_IRUGO, \ 1397 show_in, NULL, SYS_IN_ALARM, ix) 1398 1399SENSOR_DEVICE_ATTR_IN(0); 1400SENSOR_DEVICE_ATTR_IN(1); 1401SENSOR_DEVICE_ATTR_IN(2); 1402SENSOR_DEVICE_ATTR_IN(3); 1403SENSOR_DEVICE_ATTR_IN(4); 1404SENSOR_DEVICE_ATTR_IN(5); 1405SENSOR_DEVICE_ATTR_IN(6); 1406 1407/* Temperatures 1-3 */ 1408 1409#define SENSOR_DEVICE_ATTR_TEMP(ix) \ 1410static SENSOR_DEVICE_ATTR_2(temp##ix##_input, S_IRUGO, \ 1411 show_temp, NULL, SYS_TEMP_INPUT, ix-1); \ 1412static SENSOR_DEVICE_ATTR_2(temp##ix##_min, S_IRUGO | S_IWUSR, \ 1413 show_temp, set_temp, SYS_TEMP_MIN, ix-1); \ 1414static SENSOR_DEVICE_ATTR_2(temp##ix##_max, S_IRUGO | S_IWUSR, \ 1415 show_temp, set_temp, SYS_TEMP_MAX, ix-1); \ 1416static SENSOR_DEVICE_ATTR_2(temp##ix##_offset, S_IRUGO, \ 1417 show_temp, set_temp, SYS_TEMP_OFFSET, ix-1); \ 1418static SENSOR_DEVICE_ATTR_2(temp##ix##_alarm, S_IRUGO, \ 1419 show_temp, NULL, SYS_TEMP_ALARM, ix-1); \ 1420static SENSOR_DEVICE_ATTR_2(temp##ix##_fault, S_IRUGO, \ 1421 show_temp, NULL, SYS_TEMP_FAULT, ix-1) 1422 1423SENSOR_DEVICE_ATTR_TEMP(1); 1424SENSOR_DEVICE_ATTR_TEMP(2); 1425SENSOR_DEVICE_ATTR_TEMP(3); 1426 1427/* Zones 1-3 */ 1428 1429#define SENSOR_DEVICE_ATTR_ZONE(ix) \ 1430static SENSOR_DEVICE_ATTR_2(zone##ix##_auto_channels_temp, S_IRUGO, \ 1431 show_zone, NULL, SYS_ZONE_AUTO_CHANNELS_TEMP, ix-1); \ 1432static SENSOR_DEVICE_ATTR_2(zone##ix##_auto_point1_temp_hyst, S_IRUGO, \ 1433 show_zone, set_zone, SYS_ZONE_AUTO_POINT1_TEMP_HYST, ix-1); \ 1434static SENSOR_DEVICE_ATTR_2(zone##ix##_auto_point1_temp, S_IRUGO, \ 1435 show_zone, set_zone, SYS_ZONE_AUTO_POINT1_TEMP, ix-1); \ 1436static SENSOR_DEVICE_ATTR_2(zone##ix##_auto_point2_temp, S_IRUGO, \ 1437 show_zone, set_zone, SYS_ZONE_AUTO_POINT2_TEMP, ix-1); \ 1438static SENSOR_DEVICE_ATTR_2(zone##ix##_auto_point3_temp, S_IRUGO, \ 1439 show_zone, set_zone, SYS_ZONE_AUTO_POINT3_TEMP, ix-1) 1440 1441SENSOR_DEVICE_ATTR_ZONE(1); 1442SENSOR_DEVICE_ATTR_ZONE(2); 1443SENSOR_DEVICE_ATTR_ZONE(3); 1444 1445/* Fans 1-4 */ 1446 1447#define SENSOR_DEVICE_ATTR_FAN_1TO4(ix) \ 1448static SENSOR_DEVICE_ATTR_2(fan##ix##_input, S_IRUGO, \ 1449 show_fan, NULL, SYS_FAN_INPUT, ix-1); \ 1450static SENSOR_DEVICE_ATTR_2(fan##ix##_min, S_IRUGO | S_IWUSR, \ 1451 show_fan, set_fan, SYS_FAN_MIN, ix-1); \ 1452static SENSOR_DEVICE_ATTR_2(fan##ix##_alarm, S_IRUGO, \ 1453 show_fan, NULL, SYS_FAN_ALARM, ix-1); \ 1454static SENSOR_DEVICE_ATTR_2(fan##ix##_type, S_IRUGO | S_IWUSR, \ 1455 show_fan, set_fan, SYS_FAN_TYPE, ix-1) 1456 1457SENSOR_DEVICE_ATTR_FAN_1TO4(1); 1458SENSOR_DEVICE_ATTR_FAN_1TO4(2); 1459SENSOR_DEVICE_ATTR_FAN_1TO4(3); 1460SENSOR_DEVICE_ATTR_FAN_1TO4(4); 1461 1462/* Fans 5-6 */ 1463 1464#define SENSOR_DEVICE_ATTR_FAN_5TO6(ix) \ 1465static SENSOR_DEVICE_ATTR_2(fan##ix##_input, S_IRUGO, \ 1466 show_fan, NULL, SYS_FAN_INPUT, ix-1); \ 1467static SENSOR_DEVICE_ATTR_2(fan##ix##_min, S_IRUGO | S_IWUSR, \ 1468 show_fan, set_fan, SYS_FAN_MIN, ix-1); \ 1469static SENSOR_DEVICE_ATTR_2(fan##ix##_alarm, S_IRUGO, \ 1470 show_fan, NULL, SYS_FAN_ALARM, ix-1); \ 1471static SENSOR_DEVICE_ATTR_2(fan##ix##_max, S_IRUGO | S_IWUSR, \ 1472 show_fan, set_fan, SYS_FAN_MAX, ix-1) 1473 1474SENSOR_DEVICE_ATTR_FAN_5TO6(5); 1475SENSOR_DEVICE_ATTR_FAN_5TO6(6); 1476 1477/* PWMs 1-3 */ 1478 1479#define SENSOR_DEVICE_ATTR_PWM_1TO3(ix) \ 1480static SENSOR_DEVICE_ATTR_2(pwm##ix, S_IRUGO, \ 1481 show_pwm, set_pwm, SYS_PWM, ix-1); \ 1482static SENSOR_DEVICE_ATTR_2(pwm##ix##_freq, S_IRUGO, \ 1483 show_pwm, set_pwm, SYS_PWM_FREQ, ix-1); \ 1484static SENSOR_DEVICE_ATTR_2(pwm##ix##_enable, S_IRUGO, \ 1485 show_pwm, set_pwm, SYS_PWM_ENABLE, ix-1); \ 1486static SENSOR_DEVICE_ATTR_2(pwm##ix##_ramp_rate, S_IRUGO, \ 1487 show_pwm, set_pwm, SYS_PWM_RAMP_RATE, ix-1); \ 1488static SENSOR_DEVICE_ATTR_2(pwm##ix##_auto_channels_zone, S_IRUGO, \ 1489 show_pwm, set_pwm, SYS_PWM_AUTO_CHANNELS_ZONE, ix-1); \ 1490static SENSOR_DEVICE_ATTR_2(pwm##ix##_auto_pwm_min, S_IRUGO, \ 1491 show_pwm, set_pwm, SYS_PWM_AUTO_PWM_MIN, ix-1); \ 1492static SENSOR_DEVICE_ATTR_2(pwm##ix##_auto_point1_pwm, S_IRUGO, \ 1493 show_pwm, set_pwm, SYS_PWM_AUTO_POINT1_PWM, ix-1); \ 1494static SENSOR_DEVICE_ATTR_2(pwm##ix##_auto_point2_pwm, S_IRUGO, \ 1495 show_pwm, NULL, SYS_PWM_AUTO_POINT2_PWM, ix-1) 1496 1497SENSOR_DEVICE_ATTR_PWM_1TO3(1); 1498SENSOR_DEVICE_ATTR_PWM_1TO3(2); 1499SENSOR_DEVICE_ATTR_PWM_1TO3(3); 1500 1501/* PWMs 5-6 */ 1502 1503#define SENSOR_DEVICE_ATTR_PWM_5TO6(ix) \ 1504static SENSOR_DEVICE_ATTR_2(pwm##ix, S_IRUGO | S_IWUSR, \ 1505 show_pwm, set_pwm, SYS_PWM, ix-1); \ 1506static SENSOR_DEVICE_ATTR_2(pwm##ix##_freq, S_IRUGO | S_IWUSR, \ 1507 show_pwm, set_pwm, SYS_PWM_FREQ, ix-1); \ 1508static SENSOR_DEVICE_ATTR_2(pwm##ix##_enable, S_IRUGO, \ 1509 show_pwm, NULL, SYS_PWM_ENABLE, ix-1) 1510 1511SENSOR_DEVICE_ATTR_PWM_5TO6(5); 1512SENSOR_DEVICE_ATTR_PWM_5TO6(6); 1513 1514/* Misc */ 1515 1516static DEVICE_ATTR(vrm, S_IRUGO | S_IWUSR, show_vrm, set_vrm); 1517static DEVICE_ATTR(cpu0_vid, S_IRUGO, show_vid, NULL); 1518static DEVICE_ATTR(name, S_IRUGO, show_name, NULL); /* for ISA devices */ 1519 1520#define SENSOR_DEV_ATTR_IN(ix) \ 1521&sensor_dev_attr_in##ix##_input.dev_attr.attr, \ 1522&sensor_dev_attr_in##ix##_min.dev_attr.attr, \ 1523&sensor_dev_attr_in##ix##_max.dev_attr.attr, \ 1524&sensor_dev_attr_in##ix##_alarm.dev_attr.attr 1525 1526/* These attributes are read-writeable only if the chip is *not* locked */ 1527#define SENSOR_DEV_ATTR_TEMP_LOCK(ix) \ 1528&sensor_dev_attr_temp##ix##_offset.dev_attr.attr 1529 1530#define SENSOR_DEV_ATTR_TEMP(ix) \ 1531SENSOR_DEV_ATTR_TEMP_LOCK(ix), \ 1532&sensor_dev_attr_temp##ix##_input.dev_attr.attr, \ 1533&sensor_dev_attr_temp##ix##_min.dev_attr.attr, \ 1534&sensor_dev_attr_temp##ix##_max.dev_attr.attr, \ 1535&sensor_dev_attr_temp##ix##_alarm.dev_attr.attr, \ 1536&sensor_dev_attr_temp##ix##_fault.dev_attr.attr 1537 1538/* These attributes are read-writeable only if the chip is *not* locked */ 1539#define SENSOR_DEV_ATTR_ZONE_LOCK(ix) \ 1540&sensor_dev_attr_zone##ix##_auto_point1_temp_hyst.dev_attr.attr, \ 1541&sensor_dev_attr_zone##ix##_auto_point1_temp.dev_attr.attr, \ 1542&sensor_dev_attr_zone##ix##_auto_point2_temp.dev_attr.attr, \ 1543&sensor_dev_attr_zone##ix##_auto_point3_temp.dev_attr.attr 1544 1545#define SENSOR_DEV_ATTR_ZONE(ix) \ 1546SENSOR_DEV_ATTR_ZONE_LOCK(ix), \ 1547&sensor_dev_attr_zone##ix##_auto_channels_temp.dev_attr.attr 1548 1549#define SENSOR_DEV_ATTR_FAN_1TO4(ix) \ 1550&sensor_dev_attr_fan##ix##_input.dev_attr.attr, \ 1551&sensor_dev_attr_fan##ix##_min.dev_attr.attr, \ 1552&sensor_dev_attr_fan##ix##_alarm.dev_attr.attr, \ 1553&sensor_dev_attr_fan##ix##_type.dev_attr.attr 1554 1555#define SENSOR_DEV_ATTR_FAN_5TO6(ix) \ 1556&sensor_dev_attr_fan##ix##_input.dev_attr.attr, \ 1557&sensor_dev_attr_fan##ix##_min.dev_attr.attr, \ 1558&sensor_dev_attr_fan##ix##_alarm.dev_attr.attr, \ 1559&sensor_dev_attr_fan##ix##_max.dev_attr.attr 1560 1561/* These attributes are read-writeable only if the chip is *not* locked */ 1562#define SENSOR_DEV_ATTR_PWM_1TO3_LOCK(ix) \ 1563&sensor_dev_attr_pwm##ix##_freq.dev_attr.attr, \ 1564&sensor_dev_attr_pwm##ix##_enable.dev_attr.attr, \ 1565&sensor_dev_attr_pwm##ix##_ramp_rate.dev_attr.attr, \ 1566&sensor_dev_attr_pwm##ix##_auto_channels_zone.dev_attr.attr, \ 1567&sensor_dev_attr_pwm##ix##_auto_pwm_min.dev_attr.attr, \ 1568&sensor_dev_attr_pwm##ix##_auto_point1_pwm.dev_attr.attr 1569 1570#define SENSOR_DEV_ATTR_PWM_1TO3(ix) \ 1571SENSOR_DEV_ATTR_PWM_1TO3_LOCK(ix), \ 1572&sensor_dev_attr_pwm##ix.dev_attr.attr, \ 1573&sensor_dev_attr_pwm##ix##_auto_point2_pwm.dev_attr.attr 1574 1575/* These attributes are read-writeable only if the chip is *not* locked */ 1576#define SENSOR_DEV_ATTR_PWM_5TO6_LOCK(ix) \ 1577&sensor_dev_attr_pwm##ix.dev_attr.attr, \ 1578&sensor_dev_attr_pwm##ix##_freq.dev_attr.attr 1579 1580#define SENSOR_DEV_ATTR_PWM_5TO6(ix) \ 1581SENSOR_DEV_ATTR_PWM_5TO6_LOCK(ix), \ 1582&sensor_dev_attr_pwm##ix##_enable.dev_attr.attr 1583 1584/* This struct holds all the attributes that are always present and need to be 1585 * created unconditionally. The attributes that need modification of their 1586 * permissions are created read-only and write permissions are added or removed 1587 * on the fly when required */ 1588static struct attribute *dme1737_attr[] ={ 1589 /* Voltages */ 1590 SENSOR_DEV_ATTR_IN(0), 1591 SENSOR_DEV_ATTR_IN(1), 1592 SENSOR_DEV_ATTR_IN(2), 1593 SENSOR_DEV_ATTR_IN(3), 1594 SENSOR_DEV_ATTR_IN(4), 1595 SENSOR_DEV_ATTR_IN(5), 1596 SENSOR_DEV_ATTR_IN(6), 1597 /* Temperatures */ 1598 SENSOR_DEV_ATTR_TEMP(1), 1599 SENSOR_DEV_ATTR_TEMP(2), 1600 SENSOR_DEV_ATTR_TEMP(3), 1601 /* Zones */ 1602 SENSOR_DEV_ATTR_ZONE(1), 1603 SENSOR_DEV_ATTR_ZONE(2), 1604 SENSOR_DEV_ATTR_ZONE(3), 1605 /* Misc */ 1606 &dev_attr_vrm.attr, 1607 &dev_attr_cpu0_vid.attr, 1608 NULL 1609}; 1610 1611static const struct attribute_group dme1737_group = { 1612 .attrs = dme1737_attr, 1613}; 1614 1615/* The following structs hold the PWM attributes, some of which are optional. 1616 * Their creation depends on the chip configuration which is determined during 1617 * module load. */ 1618static struct attribute *dme1737_attr_pwm1[] = { 1619 SENSOR_DEV_ATTR_PWM_1TO3(1), 1620 NULL 1621}; 1622static struct attribute *dme1737_attr_pwm2[] = { 1623 SENSOR_DEV_ATTR_PWM_1TO3(2), 1624 NULL 1625}; 1626static struct attribute *dme1737_attr_pwm3[] = { 1627 SENSOR_DEV_ATTR_PWM_1TO3(3), 1628 NULL 1629}; 1630static struct attribute *dme1737_attr_pwm5[] = { 1631 SENSOR_DEV_ATTR_PWM_5TO6(5), 1632 NULL 1633}; 1634static struct attribute *dme1737_attr_pwm6[] = { 1635 SENSOR_DEV_ATTR_PWM_5TO6(6), 1636 NULL 1637}; 1638 1639static const struct attribute_group dme1737_pwm_group[] = { 1640 { .attrs = dme1737_attr_pwm1 }, 1641 { .attrs = dme1737_attr_pwm2 }, 1642 { .attrs = dme1737_attr_pwm3 }, 1643 { .attrs = NULL }, 1644 { .attrs = dme1737_attr_pwm5 }, 1645 { .attrs = dme1737_attr_pwm6 }, 1646}; 1647 1648/* The following structs hold the fan attributes, some of which are optional. 1649 * Their creation depends on the chip configuration which is determined during 1650 * module load. */ 1651static struct attribute *dme1737_attr_fan1[] = { 1652 SENSOR_DEV_ATTR_FAN_1TO4(1), 1653 NULL 1654}; 1655static struct attribute *dme1737_attr_fan2[] = { 1656 SENSOR_DEV_ATTR_FAN_1TO4(2), 1657 NULL 1658}; 1659static struct attribute *dme1737_attr_fan3[] = { 1660 SENSOR_DEV_ATTR_FAN_1TO4(3), 1661 NULL 1662}; 1663static struct attribute *dme1737_attr_fan4[] = { 1664 SENSOR_DEV_ATTR_FAN_1TO4(4), 1665 NULL 1666}; 1667static struct attribute *dme1737_attr_fan5[] = { 1668 SENSOR_DEV_ATTR_FAN_5TO6(5), 1669 NULL 1670}; 1671static struct attribute *dme1737_attr_fan6[] = { 1672 SENSOR_DEV_ATTR_FAN_5TO6(6), 1673 NULL 1674}; 1675 1676static const struct attribute_group dme1737_fan_group[] = { 1677 { .attrs = dme1737_attr_fan1 }, 1678 { .attrs = dme1737_attr_fan2 }, 1679 { .attrs = dme1737_attr_fan3 }, 1680 { .attrs = dme1737_attr_fan4 }, 1681 { .attrs = dme1737_attr_fan5 }, 1682 { .attrs = dme1737_attr_fan6 }, 1683}; 1684 1685/* The permissions of all of the following attributes are changed to read- 1686 * writeable if the chip is *not* locked. Otherwise they stay read-only. */ 1687static struct attribute *dme1737_attr_lock[] = { 1688 /* Temperatures */ 1689 SENSOR_DEV_ATTR_TEMP_LOCK(1), 1690 SENSOR_DEV_ATTR_TEMP_LOCK(2), 1691 SENSOR_DEV_ATTR_TEMP_LOCK(3), 1692 /* Zones */ 1693 SENSOR_DEV_ATTR_ZONE_LOCK(1), 1694 SENSOR_DEV_ATTR_ZONE_LOCK(2), 1695 SENSOR_DEV_ATTR_ZONE_LOCK(3), 1696 NULL 1697}; 1698 1699static const struct attribute_group dme1737_lock_group = { 1700 .attrs = dme1737_attr_lock, 1701}; 1702 1703/* The permissions of the following PWM attributes are changed to read- 1704 * writeable if the chip is *not* locked and the respective PWM is available. 1705 * Otherwise they stay read-only. */ 1706static struct attribute *dme1737_attr_pwm1_lock[] = { 1707 SENSOR_DEV_ATTR_PWM_1TO3_LOCK(1), 1708 NULL 1709}; 1710static struct attribute *dme1737_attr_pwm2_lock[] = { 1711 SENSOR_DEV_ATTR_PWM_1TO3_LOCK(2), 1712 NULL 1713}; 1714static struct attribute *dme1737_attr_pwm3_lock[] = { 1715 SENSOR_DEV_ATTR_PWM_1TO3_LOCK(3), 1716 NULL 1717}; 1718static struct attribute *dme1737_attr_pwm5_lock[] = { 1719 SENSOR_DEV_ATTR_PWM_5TO6_LOCK(5), 1720 NULL 1721}; 1722static struct attribute *dme1737_attr_pwm6_lock[] = { 1723 SENSOR_DEV_ATTR_PWM_5TO6_LOCK(6), 1724 NULL 1725}; 1726 1727static const struct attribute_group dme1737_pwm_lock_group[] = { 1728 { .attrs = dme1737_attr_pwm1_lock }, 1729 { .attrs = dme1737_attr_pwm2_lock }, 1730 { .attrs = dme1737_attr_pwm3_lock }, 1731 { .attrs = NULL }, 1732 { .attrs = dme1737_attr_pwm5_lock }, 1733 { .attrs = dme1737_attr_pwm6_lock }, 1734}; 1735 1736/* Pwm[1-3] are read-writeable if the associated pwm is in manual mode and the 1737 * chip is not locked. Otherwise they are read-only. */ 1738static struct attribute *dme1737_attr_pwm[] = { 1739 &sensor_dev_attr_pwm1.dev_attr.attr, 1740 &sensor_dev_attr_pwm2.dev_attr.attr, 1741 &sensor_dev_attr_pwm3.dev_attr.attr, 1742}; 1743 1744/* --------------------------------------------------------------------- 1745 * Super-IO functions 1746 * --------------------------------------------------------------------- */ 1747 1748static inline void dme1737_sio_enter(int sio_cip) 1749{ 1750 outb(0x55, sio_cip); 1751} 1752 1753static inline void dme1737_sio_exit(int sio_cip) 1754{ 1755 outb(0xaa, sio_cip); 1756} 1757 1758static inline int dme1737_sio_inb(int sio_cip, int reg) 1759{ 1760 outb(reg, sio_cip); 1761 return inb(sio_cip + 1); 1762} 1763 1764static inline void dme1737_sio_outb(int sio_cip, int reg, int val) 1765{ 1766 outb(reg, sio_cip); 1767 outb(val, sio_cip + 1); 1768} 1769 1770/* --------------------------------------------------------------------- 1771 * Device initialization 1772 * --------------------------------------------------------------------- */ 1773 1774static int dme1737_i2c_get_features(int, struct dme1737_data*); 1775 1776static void dme1737_chmod_file(struct device *dev, 1777 struct attribute *attr, mode_t mode) 1778{ 1779 if (sysfs_chmod_file(&dev->kobj, attr, mode)) { 1780 dev_warn(dev, "Failed to change permissions of %s.\n", 1781 attr->name); 1782 } 1783} 1784 1785static void dme1737_chmod_group(struct device *dev, 1786 const struct attribute_group *group, 1787 mode_t mode) 1788{ 1789 struct attribute **attr; 1790 1791 for (attr = group->attrs; *attr; attr++) { 1792 dme1737_chmod_file(dev, *attr, mode); 1793 } 1794} 1795 1796static void dme1737_remove_files(struct device *dev) 1797{ 1798 struct dme1737_data *data = dev_get_drvdata(dev); 1799 int ix; 1800 1801 for (ix = 0; ix < ARRAY_SIZE(dme1737_fan_group); ix++) { 1802 if (data->has_fan & (1 << ix)) { 1803 sysfs_remove_group(&dev->kobj, 1804 &dme1737_fan_group[ix]); 1805 } 1806 } 1807 1808 for (ix = 0; ix < ARRAY_SIZE(dme1737_pwm_group); ix++) { 1809 if (data->has_pwm & (1 << ix)) { 1810 sysfs_remove_group(&dev->kobj, 1811 &dme1737_pwm_group[ix]); 1812 } 1813 } 1814 1815 sysfs_remove_group(&dev->kobj, &dme1737_group); 1816 1817 if (!data->client.driver) { 1818 sysfs_remove_file(&dev->kobj, &dev_attr_name.attr); 1819 } 1820} 1821 1822static int dme1737_create_files(struct device *dev) 1823{ 1824 struct dme1737_data *data = dev_get_drvdata(dev); 1825 int err, ix; 1826 1827 /* Create a name attribute for ISA devices */ 1828 if (!data->client.driver && 1829 (err = sysfs_create_file(&dev->kobj, &dev_attr_name.attr))) { 1830 goto exit; 1831 } 1832 1833 /* Create standard sysfs attributes */ 1834 if ((err = sysfs_create_group(&dev->kobj, &dme1737_group))) { 1835 goto exit_remove; 1836 } 1837 1838 /* Create fan sysfs attributes */ 1839 for (ix = 0; ix < ARRAY_SIZE(dme1737_fan_group); ix++) { 1840 if (data->has_fan & (1 << ix)) { 1841 if ((err = sysfs_create_group(&dev->kobj, 1842 &dme1737_fan_group[ix]))) { 1843 goto exit_remove; 1844 } 1845 } 1846 } 1847 1848 /* Create PWM sysfs attributes */ 1849 for (ix = 0; ix < ARRAY_SIZE(dme1737_pwm_group); ix++) { 1850 if (data->has_pwm & (1 << ix)) { 1851 if ((err = sysfs_create_group(&dev->kobj, 1852 &dme1737_pwm_group[ix]))) { 1853 goto exit_remove; 1854 } 1855 } 1856 } 1857 1858 /* Inform if the device is locked. Otherwise change the permissions of 1859 * selected attributes from read-only to read-writeable. */ 1860 if (data->config & 0x02) { 1861 dev_info(dev, "Device is locked. Some attributes " 1862 "will be read-only.\n"); 1863 } else { 1864 /* Change permissions of standard attributes */ 1865 dme1737_chmod_group(dev, &dme1737_lock_group, 1866 S_IRUGO | S_IWUSR); 1867 1868 /* Change permissions of PWM attributes */ 1869 for (ix = 0; ix < ARRAY_SIZE(dme1737_pwm_lock_group); ix++) { 1870 if (data->has_pwm & (1 << ix)) { 1871 dme1737_chmod_group(dev, 1872 &dme1737_pwm_lock_group[ix], 1873 S_IRUGO | S_IWUSR); 1874 } 1875 } 1876 1877 /* Change permissions of pwm[1-3] if in manual mode */ 1878 for (ix = 0; ix < 3; ix++) { 1879 if ((data->has_pwm & (1 << ix)) && 1880 (PWM_EN_FROM_REG(data->pwm_config[ix]) == 1)) { 1881 dme1737_chmod_file(dev, 1882 dme1737_attr_pwm[ix], 1883 S_IRUGO | S_IWUSR); 1884 } 1885 } 1886 } 1887 1888 return 0; 1889 1890exit_remove: 1891 dme1737_remove_files(dev); 1892exit: 1893 return err; 1894} 1895 1896static int dme1737_init_device(struct device *dev) 1897{ 1898 struct dme1737_data *data = dev_get_drvdata(dev); 1899 struct i2c_client *client = &data->client; 1900 int ix; 1901 u8 reg; 1902 1903 data->config = dme1737_read(client, DME1737_REG_CONFIG); 1904 /* Inform if part is not monitoring/started */ 1905 if (!(data->config & 0x01)) { 1906 if (!force_start) { 1907 dev_err(dev, "Device is not monitoring. " 1908 "Use the force_start load parameter to " 1909 "override.\n"); 1910 return -EFAULT; 1911 } 1912 1913 /* Force monitoring */ 1914 data->config |= 0x01; 1915 dme1737_write(client, DME1737_REG_CONFIG, data->config); 1916 } 1917 /* Inform if part is not ready */ 1918 if (!(data->config & 0x04)) { 1919 dev_err(dev, "Device is not ready.\n"); 1920 return -EFAULT; 1921 } 1922 1923 /* Determine which optional fan and pwm features are enabled/present */ 1924 if (client->driver) { /* I2C chip */ 1925 data->config2 = dme1737_read(client, DME1737_REG_CONFIG2); 1926 /* Check if optional fan3 input is enabled */ 1927 if (data->config2 & 0x04) { 1928 data->has_fan |= (1 << 2); 1929 } 1930 1931 /* Fan4 and pwm3 are only available if the client's I2C address 1932 * is the default 0x2e. Otherwise the I/Os associated with 1933 * these functions are used for addr enable/select. */ 1934 if (data->client.addr == 0x2e) { 1935 data->has_fan |= (1 << 3); 1936 data->has_pwm |= (1 << 2); 1937 } 1938 1939 /* Determine which of the optional fan[5-6] and pwm[5-6] 1940 * features are enabled. For this, we need to query the runtime 1941 * registers through the Super-IO LPC interface. Try both 1942 * config ports 0x2e and 0x4e. */ 1943 if (dme1737_i2c_get_features(0x2e, data) && 1944 dme1737_i2c_get_features(0x4e, data)) { 1945 dev_warn(dev, "Failed to query Super-IO for optional " 1946 "features.\n"); 1947 } 1948 } else { /* ISA chip */ 1949 /* Fan3 and pwm3 are always available. Fan[4-5] and pwm[5-6] 1950 * don't exist in the ISA chip. */ 1951 data->has_fan |= (1 << 2); 1952 data->has_pwm |= (1 << 2); 1953 } 1954 1955 /* Fan1, fan2, pwm1, and pwm2 are always present */ 1956 data->has_fan |= 0x03; 1957 data->has_pwm |= 0x03; 1958 1959 dev_info(dev, "Optional features: pwm3=%s, pwm5=%s, pwm6=%s, " 1960 "fan3=%s, fan4=%s, fan5=%s, fan6=%s.\n", 1961 (data->has_pwm & (1 << 2)) ? "yes" : "no", 1962 (data->has_pwm & (1 << 4)) ? "yes" : "no", 1963 (data->has_pwm & (1 << 5)) ? "yes" : "no", 1964 (data->has_fan & (1 << 2)) ? "yes" : "no", 1965 (data->has_fan & (1 << 3)) ? "yes" : "no", 1966 (data->has_fan & (1 << 4)) ? "yes" : "no", 1967 (data->has_fan & (1 << 5)) ? "yes" : "no"); 1968 1969 reg = dme1737_read(client, DME1737_REG_TACH_PWM); 1970 /* Inform if fan-to-pwm mapping differs from the default */ 1971 if (client->driver && reg != 0xa4) { /* I2C chip */ 1972 dev_warn(dev, "Non-standard fan to pwm mapping: " 1973 "fan1->pwm%d, fan2->pwm%d, fan3->pwm%d, " 1974 "fan4->pwm%d. Please report to the driver " 1975 "maintainer.\n", 1976 (reg & 0x03) + 1, ((reg >> 2) & 0x03) + 1, 1977 ((reg >> 4) & 0x03) + 1, ((reg >> 6) & 0x03) + 1); 1978 } else if (!client->driver && reg != 0x24) { /* ISA chip */ 1979 dev_warn(dev, "Non-standard fan to pwm mapping: " 1980 "fan1->pwm%d, fan2->pwm%d, fan3->pwm%d. " 1981 "Please report to the driver maintainer.\n", 1982 (reg & 0x03) + 1, ((reg >> 2) & 0x03) + 1, 1983 ((reg >> 4) & 0x03) + 1); 1984 } 1985 1986 /* Switch pwm[1-3] to manual mode if they are currently disabled and 1987 * set the duty-cycles to 0% (which is identical to the PWMs being 1988 * disabled). */ 1989 if (!(data->config & 0x02)) { 1990 for (ix = 0; ix < 3; ix++) { 1991 data->pwm_config[ix] = dme1737_read(client, 1992 DME1737_REG_PWM_CONFIG(ix)); 1993 if ((data->has_pwm & (1 << ix)) && 1994 (PWM_EN_FROM_REG(data->pwm_config[ix]) == -1)) { 1995 dev_info(dev, "Switching pwm%d to " 1996 "manual mode.\n", ix + 1); 1997 data->pwm_config[ix] = PWM_EN_TO_REG(1, 1998 data->pwm_config[ix]); 1999 dme1737_write(client, DME1737_REG_PWM(ix), 0); 2000 dme1737_write(client, 2001 DME1737_REG_PWM_CONFIG(ix), 2002 data->pwm_config[ix]); 2003 } 2004 } 2005 } 2006 2007 /* Initialize the default PWM auto channels zone (acz) assignments */ 2008 data->pwm_acz[0] = 1; /* pwm1 -> zone1 */ 2009 data->pwm_acz[1] = 2; /* pwm2 -> zone2 */ 2010 data->pwm_acz[2] = 4; /* pwm3 -> zone3 */ 2011 2012 /* Set VRM */ 2013 data->vrm = vid_which_vrm(); 2014 2015 return 0; 2016} 2017 2018/* --------------------------------------------------------------------- 2019 * I2C device detection and registration 2020 * --------------------------------------------------------------------- */ 2021 2022static struct i2c_driver dme1737_i2c_driver; 2023 2024static int dme1737_i2c_get_features(int sio_cip, struct dme1737_data *data) 2025{ 2026 int err = 0, reg; 2027 u16 addr; 2028 2029 dme1737_sio_enter(sio_cip); 2030 2031 /* Check device ID 2032 * The DME1737 can return either 0x78 or 0x77 as its device ID. */ 2033 reg = force_id ? force_id : dme1737_sio_inb(sio_cip, 0x20); 2034 if (!(reg == 0x77 || reg == 0x78)) { 2035 err = -ENODEV; 2036 goto exit; 2037 } 2038 2039 /* Select logical device A (runtime registers) */ 2040 dme1737_sio_outb(sio_cip, 0x07, 0x0a); 2041 2042 /* Get the base address of the runtime registers */ 2043 if (!(addr = (dme1737_sio_inb(sio_cip, 0x60) << 8) | 2044 dme1737_sio_inb(sio_cip, 0x61))) { 2045 err = -ENODEV; 2046 goto exit; 2047 } 2048 2049 /* Read the runtime registers to determine which optional features 2050 * are enabled and available. Bits [3:2] of registers 0x43-0x46 are set 2051 * to '10' if the respective feature is enabled. */ 2052 if ((inb(addr + 0x43) & 0x0c) == 0x08) { /* fan6 */ 2053 data->has_fan |= (1 << 5); 2054 } 2055 if ((inb(addr + 0x44) & 0x0c) == 0x08) { /* pwm6 */ 2056 data->has_pwm |= (1 << 5); 2057 } 2058 if ((inb(addr + 0x45) & 0x0c) == 0x08) { /* fan5 */ 2059 data->has_fan |= (1 << 4); 2060 } 2061 if ((inb(addr + 0x46) & 0x0c) == 0x08) { /* pwm5 */ 2062 data->has_pwm |= (1 << 4); 2063 } 2064 2065exit: 2066 dme1737_sio_exit(sio_cip); 2067 2068 return err; 2069} 2070 2071static int dme1737_i2c_detect(struct i2c_adapter *adapter, int address, 2072 int kind) 2073{ 2074 u8 company, verstep = 0; 2075 struct i2c_client *client; 2076 struct dme1737_data *data; 2077 struct device *dev; 2078 int err = 0; 2079 const char *name; 2080 2081 if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) { 2082 goto exit; 2083 } 2084 2085 if (!(data = kzalloc(sizeof(struct dme1737_data), GFP_KERNEL))) { 2086 err = -ENOMEM; 2087 goto exit; 2088 } 2089 2090 client = &data->client; 2091 i2c_set_clientdata(client, data); 2092 client->addr = address; 2093 client->adapter = adapter; 2094 client->driver = &dme1737_i2c_driver; 2095 dev = &client->dev; 2096 2097 /* A negative kind means that the driver was loaded with no force 2098 * parameter (default), so we must identify the chip. */ 2099 if (kind < 0) { 2100 company = dme1737_read(client, DME1737_REG_COMPANY); 2101 verstep = dme1737_read(client, DME1737_REG_VERSTEP); 2102 2103 if (!((company == DME1737_COMPANY_SMSC) && 2104 ((verstep & DME1737_VERSTEP_MASK) == DME1737_VERSTEP))) { 2105 err = -ENODEV; 2106 goto exit_kfree; 2107 } 2108 } 2109 2110 kind = dme1737; 2111 name = "dme1737"; 2112 2113 /* Fill in the remaining client fields and put it into the global 2114 * list */ 2115 strlcpy(client->name, name, I2C_NAME_SIZE); 2116 mutex_init(&data->update_lock); 2117 2118 /* Tell the I2C layer a new client has arrived */ 2119 if ((err = i2c_attach_client(client))) { 2120 goto exit_kfree; 2121 } 2122 2123 dev_info(dev, "Found a DME1737 chip at 0x%02x (rev 0x%02x).\n", 2124 client->addr, verstep); 2125 2126 /* Initialize the DME1737 chip */ 2127 if ((err = dme1737_init_device(dev))) { 2128 dev_err(dev, "Failed to initialize device.\n"); 2129 goto exit_detach; 2130 } 2131 2132 /* Create sysfs files */ 2133 if ((err = dme1737_create_files(dev))) { 2134 dev_err(dev, "Failed to create sysfs files.\n"); 2135 goto exit_detach; 2136 } 2137 2138 /* Register device */ 2139 data->hwmon_dev = hwmon_device_register(dev); 2140 if (IS_ERR(data->hwmon_dev)) { 2141 dev_err(dev, "Failed to register device.\n"); 2142 err = PTR_ERR(data->hwmon_dev); 2143 goto exit_remove; 2144 } 2145 2146 return 0; 2147 2148exit_remove: 2149 dme1737_remove_files(dev); 2150exit_detach: 2151 i2c_detach_client(client); 2152exit_kfree: 2153 kfree(data); 2154exit: 2155 return err; 2156} 2157 2158static int dme1737_i2c_attach_adapter(struct i2c_adapter *adapter) 2159{ 2160 if (!(adapter->class & I2C_CLASS_HWMON)) { 2161 return 0; 2162 } 2163 2164 return i2c_probe(adapter, &addr_data, dme1737_i2c_detect); 2165} 2166 2167static int dme1737_i2c_detach_client(struct i2c_client *client) 2168{ 2169 struct dme1737_data *data = i2c_get_clientdata(client); 2170 int err; 2171 2172 hwmon_device_unregister(data->hwmon_dev); 2173 dme1737_remove_files(&client->dev); 2174 2175 if ((err = i2c_detach_client(client))) { 2176 return err; 2177 } 2178 2179 kfree(data); 2180 return 0; 2181} 2182 2183static struct i2c_driver dme1737_i2c_driver = { 2184 .driver = { 2185 .name = "dme1737", 2186 }, 2187 .attach_adapter = dme1737_i2c_attach_adapter, 2188 .detach_client = dme1737_i2c_detach_client, 2189}; 2190 2191/* --------------------------------------------------------------------- 2192 * ISA device detection and registration 2193 * --------------------------------------------------------------------- */ 2194 2195static int __init dme1737_isa_detect(int sio_cip, unsigned short *addr) 2196{ 2197 int err = 0, reg; 2198 unsigned short base_addr; 2199 2200 dme1737_sio_enter(sio_cip); 2201 2202 /* Check device ID 2203 * We currently know about SCH3112 (0x7c), SCH3114 (0x7d), and 2204 * SCH3116 (0x7f). */ 2205 reg = force_id ? force_id : dme1737_sio_inb(sio_cip, 0x20); 2206 if (!(reg == 0x7c || reg == 0x7d || reg == 0x7f)) { 2207 err = -ENODEV; 2208 goto exit; 2209 } 2210 2211 /* Select logical device A (runtime registers) */ 2212 dme1737_sio_outb(sio_cip, 0x07, 0x0a); 2213 2214 /* Get the base address of the runtime registers */ 2215 if (!(base_addr = (dme1737_sio_inb(sio_cip, 0x60) << 8) | 2216 dme1737_sio_inb(sio_cip, 0x61))) { 2217 printk(KERN_ERR "dme1737: Base address not set.\n"); 2218 err = -ENODEV; 2219 goto exit; 2220 } 2221 2222 /* Access to the hwmon registers is through an index/data register 2223 * pair located at offset 0x70/0x71. */ 2224 *addr = base_addr + 0x70; 2225 2226exit: 2227 dme1737_sio_exit(sio_cip); 2228 return err; 2229} 2230 2231static int __init dme1737_isa_device_add(unsigned short addr) 2232{ 2233 struct resource res = { 2234 .start = addr, 2235 .end = addr + DME1737_EXTENT - 1, 2236 .name = "dme1737", 2237 .flags = IORESOURCE_IO, 2238 }; 2239 int err; 2240 2241 if (!(pdev = platform_device_alloc("dme1737", addr))) { 2242 printk(KERN_ERR "dme1737: Failed to allocate device.\n"); 2243 err = -ENOMEM; 2244 goto exit; 2245 } 2246 2247 if ((err = platform_device_add_resources(pdev, &res, 1))) { 2248 printk(KERN_ERR "dme1737: Failed to add device resource " 2249 "(err = %d).\n", err); 2250 goto exit_device_put; 2251 } 2252 2253 if ((err = platform_device_add(pdev))) { 2254 printk(KERN_ERR "dme1737: Failed to add device (err = %d).\n", 2255 err); 2256 goto exit_device_put; 2257 } 2258 2259 return 0; 2260 2261exit_device_put: 2262 platform_device_put(pdev); 2263 pdev = NULL; 2264exit: 2265 return err; 2266} 2267 2268static int __devinit dme1737_isa_probe(struct platform_device *pdev) 2269{ 2270 u8 company, device; 2271 struct resource *res; 2272 struct i2c_client *client; 2273 struct dme1737_data *data; 2274 struct device *dev = &pdev->dev; 2275 int err; 2276 2277 res = platform_get_resource(pdev, IORESOURCE_IO, 0); 2278 if (!request_region(res->start, DME1737_EXTENT, "dme1737")) { 2279 dev_err(dev, "Failed to request region 0x%04x-0x%04x.\n", 2280 (unsigned short)res->start, 2281 (unsigned short)res->start + DME1737_EXTENT - 1); 2282 err = -EBUSY; 2283 goto exit; 2284 } 2285 2286 if (!(data = kzalloc(sizeof(struct dme1737_data), GFP_KERNEL))) { 2287 err = -ENOMEM; 2288 goto exit_release_region; 2289 } 2290 2291 client = &data->client; 2292 i2c_set_clientdata(client, data); 2293 client->addr = res->start; 2294 platform_set_drvdata(pdev, data); 2295 2296 company = dme1737_read(client, DME1737_REG_COMPANY); 2297 device = dme1737_read(client, DME1737_REG_DEVICE); 2298 2299 if (!((company == DME1737_COMPANY_SMSC) && 2300 (device == SCH311X_DEVICE))) { 2301 err = -ENODEV; 2302 goto exit_kfree; 2303 } 2304 2305 /* Fill in the remaining client fields and initialize the mutex */ 2306 strlcpy(client->name, "sch311x", I2C_NAME_SIZE); 2307 mutex_init(&data->update_lock); 2308 2309 dev_info(dev, "Found a SCH311x chip at 0x%04x\n", client->addr); 2310 2311 /* Initialize the chip */ 2312 if ((err = dme1737_init_device(dev))) { 2313 dev_err(dev, "Failed to initialize device.\n"); 2314 goto exit_kfree; 2315 } 2316 2317 /* Create sysfs files */ 2318 if ((err = dme1737_create_files(dev))) { 2319 dev_err(dev, "Failed to create sysfs files.\n"); 2320 goto exit_kfree; 2321 } 2322 2323 /* Register device */ 2324 data->hwmon_dev = hwmon_device_register(dev); 2325 if (IS_ERR(data->hwmon_dev)) { 2326 dev_err(dev, "Failed to register device.\n"); 2327 err = PTR_ERR(data->hwmon_dev); 2328 goto exit_remove_files; 2329 } 2330 2331 return 0; 2332 2333exit_remove_files: 2334 dme1737_remove_files(dev); 2335exit_kfree: 2336 platform_set_drvdata(pdev, NULL); 2337 kfree(data); 2338exit_release_region: 2339 release_region(res->start, DME1737_EXTENT); 2340exit: 2341 return err; 2342} 2343 2344static int __devexit dme1737_isa_remove(struct platform_device *pdev) 2345{ 2346 struct dme1737_data *data = platform_get_drvdata(pdev); 2347 2348 hwmon_device_unregister(data->hwmon_dev); 2349 dme1737_remove_files(&pdev->dev); 2350 release_region(data->client.addr, DME1737_EXTENT); 2351 platform_set_drvdata(pdev, NULL); 2352 kfree(data); 2353 2354 return 0; 2355} 2356 2357static struct platform_driver dme1737_isa_driver = { 2358 .driver = { 2359 .owner = THIS_MODULE, 2360 .name = "dme1737", 2361 }, 2362 .probe = dme1737_isa_probe, 2363 .remove = __devexit_p(dme1737_isa_remove), 2364}; 2365 2366/* --------------------------------------------------------------------- 2367 * Module initialization and cleanup 2368 * --------------------------------------------------------------------- */ 2369 2370static int __init dme1737_init(void) 2371{ 2372 int err; 2373 unsigned short addr; 2374 2375 if ((err = i2c_add_driver(&dme1737_i2c_driver))) { 2376 goto exit; 2377 } 2378 2379 if (dme1737_isa_detect(0x2e, &addr) && 2380 dme1737_isa_detect(0x4e, &addr)) { 2381 /* Return 0 if we didn't find an ISA device */ 2382 return 0; 2383 } 2384 2385 if ((err = platform_driver_register(&dme1737_isa_driver))) { 2386 goto exit_del_i2c_driver; 2387 } 2388 2389 /* Sets global pdev as a side effect */ 2390 if ((err = dme1737_isa_device_add(addr))) { 2391 goto exit_del_isa_driver; 2392 } 2393 2394 return 0; 2395 2396exit_del_isa_driver: 2397 platform_driver_unregister(&dme1737_isa_driver); 2398exit_del_i2c_driver: 2399 i2c_del_driver(&dme1737_i2c_driver); 2400exit: 2401 return err; 2402} 2403 2404static void __exit dme1737_exit(void) 2405{ 2406 if (pdev) { 2407 platform_device_unregister(pdev); 2408 platform_driver_unregister(&dme1737_isa_driver); 2409 } 2410 2411 i2c_del_driver(&dme1737_i2c_driver); 2412} 2413 2414MODULE_AUTHOR("Juerg Haefliger <juergh@gmail.com>"); 2415MODULE_DESCRIPTION("DME1737 sensors"); 2416MODULE_LICENSE("GPL"); 2417 2418module_init(dme1737_init); 2419module_exit(dme1737_exit); 2420