ide-dma.c revision 8704de8f296fcf6a4b2ff6bfd9a63974ad909b3e
1/* 2 * linux/drivers/ide/ide-dma.c Version 4.10 June 9, 2000 3 * 4 * Copyright (c) 1999-2000 Andre Hedrick <andre@linux-ide.org> 5 * May be copied or modified under the terms of the GNU General Public License 6 */ 7 8/* 9 * Special Thanks to Mark for his Six years of work. 10 * 11 * Copyright (c) 1995-1998 Mark Lord 12 * May be copied or modified under the terms of the GNU General Public License 13 */ 14 15/* 16 * This module provides support for the bus-master IDE DMA functions 17 * of various PCI chipsets, including the Intel PIIX (i82371FB for 18 * the 430 FX chipset), the PIIX3 (i82371SB for the 430 HX/VX and 19 * 440 chipsets), and the PIIX4 (i82371AB for the 430 TX chipset) 20 * ("PIIX" stands for "PCI ISA IDE Xcellerator"). 21 * 22 * Pretty much the same code works for other IDE PCI bus-mastering chipsets. 23 * 24 * DMA is supported for all IDE devices (disk drives, cdroms, tapes, floppies). 25 * 26 * By default, DMA support is prepared for use, but is currently enabled only 27 * for drives which already have DMA enabled (UltraDMA or mode 2 multi/single), 28 * or which are recognized as "good" (see table below). Drives with only mode0 29 * or mode1 (multi/single) DMA should also work with this chipset/driver 30 * (eg. MC2112A) but are not enabled by default. 31 * 32 * Use "hdparm -i" to view modes supported by a given drive. 33 * 34 * The hdparm-3.5 (or later) utility can be used for manually enabling/disabling 35 * DMA support, but must be (re-)compiled against this kernel version or later. 36 * 37 * To enable DMA, use "hdparm -d1 /dev/hd?" on a per-drive basis after booting. 38 * If problems arise, ide.c will disable DMA operation after a few retries. 39 * This error recovery mechanism works and has been extremely well exercised. 40 * 41 * IDE drives, depending on their vintage, may support several different modes 42 * of DMA operation. The boot-time modes are indicated with a "*" in 43 * the "hdparm -i" listing, and can be changed with *knowledgeable* use of 44 * the "hdparm -X" feature. There is seldom a need to do this, as drives 45 * normally power-up with their "best" PIO/DMA modes enabled. 46 * 47 * Testing has been done with a rather extensive number of drives, 48 * with Quantum & Western Digital models generally outperforming the pack, 49 * and Fujitsu & Conner (and some Seagate which are really Conner) drives 50 * showing more lackluster throughput. 51 * 52 * Keep an eye on /var/adm/messages for "DMA disabled" messages. 53 * 54 * Some people have reported trouble with Intel Zappa motherboards. 55 * This can be fixed by upgrading the AMI BIOS to version 1.00.04.BS0, 56 * available from ftp://ftp.intel.com/pub/bios/10004bs0.exe 57 * (thanks to Glen Morrell <glen@spin.Stanford.edu> for researching this). 58 * 59 * Thanks to "Christopher J. Reimer" <reimer@doe.carleton.ca> for 60 * fixing the problem with the BIOS on some Acer motherboards. 61 * 62 * Thanks to "Benoit Poulot-Cazajous" <poulot@chorus.fr> for testing 63 * "TX" chipset compatibility and for providing patches for the "TX" chipset. 64 * 65 * Thanks to Christian Brunner <chb@muc.de> for taking a good first crack 66 * at generic DMA -- his patches were referred to when preparing this code. 67 * 68 * Most importantly, thanks to Robert Bringman <rob@mars.trion.com> 69 * for supplying a Promise UDMA board & WD UDMA drive for this work! 70 * 71 * And, yes, Intel Zappa boards really *do* use both PIIX IDE ports. 72 * 73 * ATA-66/100 and recovery functions, I forgot the rest...... 74 * 75 */ 76 77#include <linux/module.h> 78#include <linux/types.h> 79#include <linux/kernel.h> 80#include <linux/timer.h> 81#include <linux/mm.h> 82#include <linux/interrupt.h> 83#include <linux/pci.h> 84#include <linux/init.h> 85#include <linux/ide.h> 86#include <linux/delay.h> 87#include <linux/scatterlist.h> 88 89#include <asm/io.h> 90#include <asm/irq.h> 91 92static const struct drive_list_entry drive_whitelist [] = { 93 94 { "Micropolis 2112A" , NULL }, 95 { "CONNER CTMA 4000" , NULL }, 96 { "CONNER CTT8000-A" , NULL }, 97 { "ST34342A" , NULL }, 98 { NULL , NULL } 99}; 100 101static const struct drive_list_entry drive_blacklist [] = { 102 103 { "WDC AC11000H" , NULL }, 104 { "WDC AC22100H" , NULL }, 105 { "WDC AC32500H" , NULL }, 106 { "WDC AC33100H" , NULL }, 107 { "WDC AC31600H" , NULL }, 108 { "WDC AC32100H" , "24.09P07" }, 109 { "WDC AC23200L" , "21.10N21" }, 110 { "Compaq CRD-8241B" , NULL }, 111 { "CRD-8400B" , NULL }, 112 { "CRD-8480B", NULL }, 113 { "CRD-8482B", NULL }, 114 { "CRD-84" , NULL }, 115 { "SanDisk SDP3B" , NULL }, 116 { "SanDisk SDP3B-64" , NULL }, 117 { "SANYO CD-ROM CRD" , NULL }, 118 { "HITACHI CDR-8" , NULL }, 119 { "HITACHI CDR-8335" , NULL }, 120 { "HITACHI CDR-8435" , NULL }, 121 { "Toshiba CD-ROM XM-6202B" , NULL }, 122 { "TOSHIBA CD-ROM XM-1702BC", NULL }, 123 { "CD-532E-A" , NULL }, 124 { "E-IDE CD-ROM CR-840", NULL }, 125 { "CD-ROM Drive/F5A", NULL }, 126 { "WPI CDD-820", NULL }, 127 { "SAMSUNG CD-ROM SC-148C", NULL }, 128 { "SAMSUNG CD-ROM SC", NULL }, 129 { "ATAPI CD-ROM DRIVE 40X MAXIMUM", NULL }, 130 { "_NEC DV5800A", NULL }, 131 { "SAMSUNG CD-ROM SN-124", "N001" }, 132 { "Seagate STT20000A", NULL }, 133 { "CD-ROM CDR_U200", "1.09" }, 134 { NULL , NULL } 135 136}; 137 138/** 139 * ide_dma_intr - IDE DMA interrupt handler 140 * @drive: the drive the interrupt is for 141 * 142 * Handle an interrupt completing a read/write DMA transfer on an 143 * IDE device 144 */ 145 146ide_startstop_t ide_dma_intr (ide_drive_t *drive) 147{ 148 u8 stat = 0, dma_stat = 0; 149 150 dma_stat = HWIF(drive)->ide_dma_end(drive); 151 stat = HWIF(drive)->INB(IDE_STATUS_REG); /* get drive status */ 152 if (OK_STAT(stat,DRIVE_READY,drive->bad_wstat|DRQ_STAT)) { 153 if (!dma_stat) { 154 struct request *rq = HWGROUP(drive)->rq; 155 156 if (rq->rq_disk) { 157 ide_driver_t *drv; 158 159 drv = *(ide_driver_t **)rq->rq_disk->private_data; 160 drv->end_request(drive, 1, rq->nr_sectors); 161 } else 162 ide_end_request(drive, 1, rq->nr_sectors); 163 return ide_stopped; 164 } 165 printk(KERN_ERR "%s: dma_intr: bad DMA status (dma_stat=%x)\n", 166 drive->name, dma_stat); 167 } 168 return ide_error(drive, "dma_intr", stat); 169} 170 171EXPORT_SYMBOL_GPL(ide_dma_intr); 172 173static int ide_dma_good_drive(ide_drive_t *drive) 174{ 175 return ide_in_drive_list(drive->id, drive_whitelist); 176} 177 178#ifdef CONFIG_BLK_DEV_IDEDMA_PCI 179/** 180 * ide_build_sglist - map IDE scatter gather for DMA I/O 181 * @drive: the drive to build the DMA table for 182 * @rq: the request holding the sg list 183 * 184 * Perform the PCI mapping magic necessary to access the source or 185 * target buffers of a request via PCI DMA. The lower layers of the 186 * kernel provide the necessary cache management so that we can 187 * operate in a portable fashion 188 */ 189 190int ide_build_sglist(ide_drive_t *drive, struct request *rq) 191{ 192 ide_hwif_t *hwif = HWIF(drive); 193 struct scatterlist *sg = hwif->sg_table; 194 195 BUG_ON((rq->cmd_type == REQ_TYPE_ATA_TASKFILE) && rq->nr_sectors > 256); 196 197 ide_map_sg(drive, rq); 198 199 if (rq_data_dir(rq) == READ) 200 hwif->sg_dma_direction = PCI_DMA_FROMDEVICE; 201 else 202 hwif->sg_dma_direction = PCI_DMA_TODEVICE; 203 204 return pci_map_sg(hwif->pci_dev, sg, hwif->sg_nents, hwif->sg_dma_direction); 205} 206 207EXPORT_SYMBOL_GPL(ide_build_sglist); 208 209/** 210 * ide_build_dmatable - build IDE DMA table 211 * 212 * ide_build_dmatable() prepares a dma request. We map the command 213 * to get the pci bus addresses of the buffers and then build up 214 * the PRD table that the IDE layer wants to be fed. The code 215 * knows about the 64K wrap bug in the CS5530. 216 * 217 * Returns the number of built PRD entries if all went okay, 218 * returns 0 otherwise. 219 * 220 * May also be invoked from trm290.c 221 */ 222 223int ide_build_dmatable (ide_drive_t *drive, struct request *rq) 224{ 225 ide_hwif_t *hwif = HWIF(drive); 226 unsigned int *table = hwif->dmatable_cpu; 227 unsigned int is_trm290 = (hwif->chipset == ide_trm290) ? 1 : 0; 228 unsigned int count = 0; 229 int i; 230 struct scatterlist *sg; 231 232 hwif->sg_nents = i = ide_build_sglist(drive, rq); 233 234 if (!i) 235 return 0; 236 237 sg = hwif->sg_table; 238 while (i) { 239 u32 cur_addr; 240 u32 cur_len; 241 242 cur_addr = sg_dma_address(sg); 243 cur_len = sg_dma_len(sg); 244 245 /* 246 * Fill in the dma table, without crossing any 64kB boundaries. 247 * Most hardware requires 16-bit alignment of all blocks, 248 * but the trm290 requires 32-bit alignment. 249 */ 250 251 while (cur_len) { 252 if (count++ >= PRD_ENTRIES) { 253 printk(KERN_ERR "%s: DMA table too small\n", drive->name); 254 goto use_pio_instead; 255 } else { 256 u32 xcount, bcount = 0x10000 - (cur_addr & 0xffff); 257 258 if (bcount > cur_len) 259 bcount = cur_len; 260 *table++ = cpu_to_le32(cur_addr); 261 xcount = bcount & 0xffff; 262 if (is_trm290) 263 xcount = ((xcount >> 2) - 1) << 16; 264 if (xcount == 0x0000) { 265 /* 266 * Most chipsets correctly interpret a length of 0x0000 as 64KB, 267 * but at least one (e.g. CS5530) misinterprets it as zero (!). 268 * So here we break the 64KB entry into two 32KB entries instead. 269 */ 270 if (count++ >= PRD_ENTRIES) { 271 printk(KERN_ERR "%s: DMA table too small\n", drive->name); 272 goto use_pio_instead; 273 } 274 *table++ = cpu_to_le32(0x8000); 275 *table++ = cpu_to_le32(cur_addr + 0x8000); 276 xcount = 0x8000; 277 } 278 *table++ = cpu_to_le32(xcount); 279 cur_addr += bcount; 280 cur_len -= bcount; 281 } 282 } 283 284 sg = sg_next(sg); 285 i--; 286 } 287 288 if (count) { 289 if (!is_trm290) 290 *--table |= cpu_to_le32(0x80000000); 291 return count; 292 } 293 printk(KERN_ERR "%s: empty DMA table?\n", drive->name); 294use_pio_instead: 295 pci_unmap_sg(hwif->pci_dev, 296 hwif->sg_table, 297 hwif->sg_nents, 298 hwif->sg_dma_direction); 299 return 0; /* revert to PIO for this request */ 300} 301 302EXPORT_SYMBOL_GPL(ide_build_dmatable); 303 304/** 305 * ide_destroy_dmatable - clean up DMA mapping 306 * @drive: The drive to unmap 307 * 308 * Teardown mappings after DMA has completed. This must be called 309 * after the completion of each use of ide_build_dmatable and before 310 * the next use of ide_build_dmatable. Failure to do so will cause 311 * an oops as only one mapping can be live for each target at a given 312 * time. 313 */ 314 315void ide_destroy_dmatable (ide_drive_t *drive) 316{ 317 struct pci_dev *dev = HWIF(drive)->pci_dev; 318 struct scatterlist *sg = HWIF(drive)->sg_table; 319 int nents = HWIF(drive)->sg_nents; 320 321 pci_unmap_sg(dev, sg, nents, HWIF(drive)->sg_dma_direction); 322} 323 324EXPORT_SYMBOL_GPL(ide_destroy_dmatable); 325 326/** 327 * config_drive_for_dma - attempt to activate IDE DMA 328 * @drive: the drive to place in DMA mode 329 * 330 * If the drive supports at least mode 2 DMA or UDMA of any kind 331 * then attempt to place it into DMA mode. Drives that are known to 332 * support DMA but predate the DMA properties or that are known 333 * to have DMA handling bugs are also set up appropriately based 334 * on the good/bad drive lists. 335 */ 336 337static int config_drive_for_dma (ide_drive_t *drive) 338{ 339 ide_hwif_t *hwif = drive->hwif; 340 struct hd_driveid *id = drive->id; 341 342 if (drive->media != ide_disk) { 343 if (hwif->host_flags & IDE_HFLAG_NO_ATAPI_DMA) 344 return 0; 345 } 346 347 /* 348 * Enable DMA on any drive that has 349 * UltraDMA (mode 0/1/2/3/4/5/6) enabled 350 */ 351 if ((id->field_valid & 4) && ((id->dma_ultra >> 8) & 0x7f)) 352 return 1; 353 354 /* 355 * Enable DMA on any drive that has mode2 DMA 356 * (multi or single) enabled 357 */ 358 if (id->field_valid & 2) /* regular DMA */ 359 if ((id->dma_mword & 0x404) == 0x404 || 360 (id->dma_1word & 0x404) == 0x404) 361 return 1; 362 363 /* Consult the list of known "good" drives */ 364 if (ide_dma_good_drive(drive)) 365 return 1; 366 367 return 0; 368} 369 370/** 371 * dma_timer_expiry - handle a DMA timeout 372 * @drive: Drive that timed out 373 * 374 * An IDE DMA transfer timed out. In the event of an error we ask 375 * the driver to resolve the problem, if a DMA transfer is still 376 * in progress we continue to wait (arguably we need to add a 377 * secondary 'I don't care what the drive thinks' timeout here) 378 * Finally if we have an interrupt we let it complete the I/O. 379 * But only one time - we clear expiry and if it's still not 380 * completed after WAIT_CMD, we error and retry in PIO. 381 * This can occur if an interrupt is lost or due to hang or bugs. 382 */ 383 384static int dma_timer_expiry (ide_drive_t *drive) 385{ 386 ide_hwif_t *hwif = HWIF(drive); 387 u8 dma_stat = hwif->INB(hwif->dma_status); 388 389 printk(KERN_WARNING "%s: dma_timer_expiry: dma status == 0x%02x\n", 390 drive->name, dma_stat); 391 392 if ((dma_stat & 0x18) == 0x18) /* BUSY Stupid Early Timer !! */ 393 return WAIT_CMD; 394 395 HWGROUP(drive)->expiry = NULL; /* one free ride for now */ 396 397 /* 1 dmaing, 2 error, 4 intr */ 398 if (dma_stat & 2) /* ERROR */ 399 return -1; 400 401 if (dma_stat & 1) /* DMAing */ 402 return WAIT_CMD; 403 404 if (dma_stat & 4) /* Got an Interrupt */ 405 return WAIT_CMD; 406 407 return 0; /* Status is unknown -- reset the bus */ 408} 409 410/** 411 * ide_dma_host_off - Generic DMA kill 412 * @drive: drive to control 413 * 414 * Perform the generic IDE controller DMA off operation. This 415 * works for most IDE bus mastering controllers 416 */ 417 418void ide_dma_host_off(ide_drive_t *drive) 419{ 420 ide_hwif_t *hwif = HWIF(drive); 421 u8 unit = (drive->select.b.unit & 0x01); 422 u8 dma_stat = hwif->INB(hwif->dma_status); 423 424 hwif->OUTB((dma_stat & ~(1<<(5+unit))), hwif->dma_status); 425} 426 427EXPORT_SYMBOL(ide_dma_host_off); 428 429/** 430 * ide_dma_off_quietly - Generic DMA kill 431 * @drive: drive to control 432 * 433 * Turn off the current DMA on this IDE controller. 434 */ 435 436void ide_dma_off_quietly(ide_drive_t *drive) 437{ 438 drive->using_dma = 0; 439 ide_toggle_bounce(drive, 0); 440 441 drive->hwif->dma_host_off(drive); 442} 443 444EXPORT_SYMBOL(ide_dma_off_quietly); 445#endif /* CONFIG_BLK_DEV_IDEDMA_PCI */ 446 447/** 448 * ide_dma_off - disable DMA on a device 449 * @drive: drive to disable DMA on 450 * 451 * Disable IDE DMA for a device on this IDE controller. 452 * Inform the user that DMA has been disabled. 453 */ 454 455void ide_dma_off(ide_drive_t *drive) 456{ 457 printk(KERN_INFO "%s: DMA disabled\n", drive->name); 458 drive->hwif->dma_off_quietly(drive); 459} 460 461EXPORT_SYMBOL(ide_dma_off); 462 463#ifdef CONFIG_BLK_DEV_IDEDMA_PCI 464/** 465 * ide_dma_host_on - Enable DMA on a host 466 * @drive: drive to enable for DMA 467 * 468 * Enable DMA on an IDE controller following generic bus mastering 469 * IDE controller behaviour 470 */ 471 472void ide_dma_host_on(ide_drive_t *drive) 473{ 474 if (drive->using_dma) { 475 ide_hwif_t *hwif = HWIF(drive); 476 u8 unit = (drive->select.b.unit & 0x01); 477 u8 dma_stat = hwif->INB(hwif->dma_status); 478 479 hwif->OUTB((dma_stat|(1<<(5+unit))), hwif->dma_status); 480 } 481} 482 483EXPORT_SYMBOL(ide_dma_host_on); 484 485/** 486 * __ide_dma_on - Enable DMA on a device 487 * @drive: drive to enable DMA on 488 * 489 * Enable IDE DMA for a device on this IDE controller. 490 */ 491 492int __ide_dma_on (ide_drive_t *drive) 493{ 494 drive->using_dma = 1; 495 ide_toggle_bounce(drive, 1); 496 497 drive->hwif->dma_host_on(drive); 498 499 return 0; 500} 501 502EXPORT_SYMBOL(__ide_dma_on); 503 504/** 505 * ide_dma_setup - begin a DMA phase 506 * @drive: target device 507 * 508 * Build an IDE DMA PRD (IDE speak for scatter gather table) 509 * and then set up the DMA transfer registers for a device 510 * that follows generic IDE PCI DMA behaviour. Controllers can 511 * override this function if they need to 512 * 513 * Returns 0 on success. If a PIO fallback is required then 1 514 * is returned. 515 */ 516 517int ide_dma_setup(ide_drive_t *drive) 518{ 519 ide_hwif_t *hwif = drive->hwif; 520 struct request *rq = HWGROUP(drive)->rq; 521 unsigned int reading; 522 u8 dma_stat; 523 524 if (rq_data_dir(rq)) 525 reading = 0; 526 else 527 reading = 1 << 3; 528 529 /* fall back to pio! */ 530 if (!ide_build_dmatable(drive, rq)) { 531 ide_map_sg(drive, rq); 532 return 1; 533 } 534 535 /* PRD table */ 536 if (hwif->mmio) 537 writel(hwif->dmatable_dma, (void __iomem *)hwif->dma_prdtable); 538 else 539 outl(hwif->dmatable_dma, hwif->dma_prdtable); 540 541 /* specify r/w */ 542 hwif->OUTB(reading, hwif->dma_command); 543 544 /* read dma_status for INTR & ERROR flags */ 545 dma_stat = hwif->INB(hwif->dma_status); 546 547 /* clear INTR & ERROR flags */ 548 hwif->OUTB(dma_stat|6, hwif->dma_status); 549 drive->waiting_for_dma = 1; 550 return 0; 551} 552 553EXPORT_SYMBOL_GPL(ide_dma_setup); 554 555static void ide_dma_exec_cmd(ide_drive_t *drive, u8 command) 556{ 557 /* issue cmd to drive */ 558 ide_execute_command(drive, command, &ide_dma_intr, 2*WAIT_CMD, dma_timer_expiry); 559} 560 561void ide_dma_start(ide_drive_t *drive) 562{ 563 ide_hwif_t *hwif = HWIF(drive); 564 u8 dma_cmd = hwif->INB(hwif->dma_command); 565 566 /* Note that this is done *after* the cmd has 567 * been issued to the drive, as per the BM-IDE spec. 568 * The Promise Ultra33 doesn't work correctly when 569 * we do this part before issuing the drive cmd. 570 */ 571 /* start DMA */ 572 hwif->OUTB(dma_cmd|1, hwif->dma_command); 573 hwif->dma = 1; 574 wmb(); 575} 576 577EXPORT_SYMBOL_GPL(ide_dma_start); 578 579/* returns 1 on error, 0 otherwise */ 580int __ide_dma_end (ide_drive_t *drive) 581{ 582 ide_hwif_t *hwif = HWIF(drive); 583 u8 dma_stat = 0, dma_cmd = 0; 584 585 drive->waiting_for_dma = 0; 586 /* get dma_command mode */ 587 dma_cmd = hwif->INB(hwif->dma_command); 588 /* stop DMA */ 589 hwif->OUTB(dma_cmd&~1, hwif->dma_command); 590 /* get DMA status */ 591 dma_stat = hwif->INB(hwif->dma_status); 592 /* clear the INTR & ERROR bits */ 593 hwif->OUTB(dma_stat|6, hwif->dma_status); 594 /* purge DMA mappings */ 595 ide_destroy_dmatable(drive); 596 /* verify good DMA status */ 597 hwif->dma = 0; 598 wmb(); 599 return (dma_stat & 7) != 4 ? (0x10 | dma_stat) : 0; 600} 601 602EXPORT_SYMBOL(__ide_dma_end); 603 604/* returns 1 if dma irq issued, 0 otherwise */ 605static int __ide_dma_test_irq(ide_drive_t *drive) 606{ 607 ide_hwif_t *hwif = HWIF(drive); 608 u8 dma_stat = hwif->INB(hwif->dma_status); 609 610 /* return 1 if INTR asserted */ 611 if ((dma_stat & 4) == 4) 612 return 1; 613 if (!drive->waiting_for_dma) 614 printk(KERN_WARNING "%s: (%s) called while not waiting\n", 615 drive->name, __FUNCTION__); 616 return 0; 617} 618#else 619static inline int config_drive_for_dma(ide_drive_t *drive) { return 0; } 620#endif /* CONFIG_BLK_DEV_IDEDMA_PCI */ 621 622int __ide_dma_bad_drive (ide_drive_t *drive) 623{ 624 struct hd_driveid *id = drive->id; 625 626 int blacklist = ide_in_drive_list(id, drive_blacklist); 627 if (blacklist) { 628 printk(KERN_WARNING "%s: Disabling (U)DMA for %s (blacklisted)\n", 629 drive->name, id->model); 630 return blacklist; 631 } 632 return 0; 633} 634 635EXPORT_SYMBOL(__ide_dma_bad_drive); 636 637static const u8 xfer_mode_bases[] = { 638 XFER_UDMA_0, 639 XFER_MW_DMA_0, 640 XFER_SW_DMA_0, 641}; 642 643static unsigned int ide_get_mode_mask(ide_drive_t *drive, u8 base, u8 req_mode) 644{ 645 struct hd_driveid *id = drive->id; 646 ide_hwif_t *hwif = drive->hwif; 647 unsigned int mask = 0; 648 649 switch(base) { 650 case XFER_UDMA_0: 651 if ((id->field_valid & 4) == 0) 652 break; 653 654 if (hwif->udma_filter) 655 mask = hwif->udma_filter(drive); 656 else 657 mask = hwif->ultra_mask; 658 mask &= id->dma_ultra; 659 660 /* 661 * avoid false cable warning from eighty_ninty_three() 662 */ 663 if (req_mode > XFER_UDMA_2) { 664 if ((mask & 0x78) && (eighty_ninty_three(drive) == 0)) 665 mask &= 0x07; 666 } 667 break; 668 case XFER_MW_DMA_0: 669 if ((id->field_valid & 2) == 0) 670 break; 671 if (hwif->mdma_filter) 672 mask = hwif->mdma_filter(drive); 673 else 674 mask = hwif->mwdma_mask; 675 mask &= id->dma_mword; 676 break; 677 case XFER_SW_DMA_0: 678 if (id->field_valid & 2) { 679 mask = id->dma_1word & hwif->swdma_mask; 680 } else if (id->tDMA) { 681 /* 682 * ide_fix_driveid() doesn't convert ->tDMA to the 683 * CPU endianness so we need to do it here 684 */ 685 u8 mode = le16_to_cpu(id->tDMA); 686 687 /* 688 * if the mode is valid convert it to the mask 689 * (the maximum allowed mode is XFER_SW_DMA_2) 690 */ 691 if (mode <= 2) 692 mask = ((2 << mode) - 1) & hwif->swdma_mask; 693 } 694 break; 695 default: 696 BUG(); 697 break; 698 } 699 700 return mask; 701} 702 703/** 704 * ide_find_dma_mode - compute DMA speed 705 * @drive: IDE device 706 * @req_mode: requested mode 707 * 708 * Checks the drive/host capabilities and finds the speed to use for 709 * the DMA transfer. The speed is then limited by the requested mode. 710 * 711 * Returns 0 if the drive/host combination is incapable of DMA transfers 712 * or if the requested mode is not a DMA mode. 713 */ 714 715u8 ide_find_dma_mode(ide_drive_t *drive, u8 req_mode) 716{ 717 ide_hwif_t *hwif = drive->hwif; 718 unsigned int mask; 719 int x, i; 720 u8 mode = 0; 721 722 if (drive->media != ide_disk) { 723 if (hwif->host_flags & IDE_HFLAG_NO_ATAPI_DMA) 724 return 0; 725 } 726 727 for (i = 0; i < ARRAY_SIZE(xfer_mode_bases); i++) { 728 if (req_mode < xfer_mode_bases[i]) 729 continue; 730 mask = ide_get_mode_mask(drive, xfer_mode_bases[i], req_mode); 731 x = fls(mask) - 1; 732 if (x >= 0) { 733 mode = xfer_mode_bases[i] + x; 734 break; 735 } 736 } 737 738 if (hwif->chipset == ide_acorn && mode == 0) { 739 /* 740 * is this correct? 741 */ 742 if (ide_dma_good_drive(drive) && drive->id->eide_dma_time < 150) 743 mode = XFER_MW_DMA_1; 744 } 745 746 mode = min(mode, req_mode); 747 748 printk(KERN_INFO "%s: %s mode selected\n", drive->name, 749 mode ? ide_xfer_verbose(mode) : "no DMA"); 750 751 return mode; 752} 753 754EXPORT_SYMBOL_GPL(ide_find_dma_mode); 755 756static int ide_tune_dma(ide_drive_t *drive) 757{ 758 ide_hwif_t *hwif = drive->hwif; 759 u8 speed; 760 761 if (noautodma || drive->nodma || (drive->id->capability & 1) == 0) 762 return 0; 763 764 /* consult the list of known "bad" drives */ 765 if (__ide_dma_bad_drive(drive)) 766 return 0; 767 768 if (ide_id_dma_bug(drive)) 769 return 0; 770 771 if (hwif->host_flags & IDE_HFLAG_TRUST_BIOS_FOR_DMA) 772 return config_drive_for_dma(drive); 773 774 speed = ide_max_dma_mode(drive); 775 776 if (!speed) { 777 /* is this really correct/needed? */ 778 if ((hwif->host_flags & IDE_HFLAG_CY82C693) && 779 ide_dma_good_drive(drive)) 780 return 1; 781 else 782 return 0; 783 } 784 785 if (hwif->host_flags & IDE_HFLAG_NO_SET_MODE) 786 return 0; 787 788 if (ide_set_dma_mode(drive, speed)) 789 return 0; 790 791 return 1; 792} 793 794static int ide_dma_check(ide_drive_t *drive) 795{ 796 ide_hwif_t *hwif = drive->hwif; 797 int vdma = (hwif->host_flags & IDE_HFLAG_VDMA)? 1 : 0; 798 799 if (!vdma && ide_tune_dma(drive)) 800 return 0; 801 802 /* TODO: always do PIO fallback */ 803 if (hwif->host_flags & IDE_HFLAG_TRUST_BIOS_FOR_DMA) 804 return -1; 805 806 ide_set_max_pio(drive); 807 808 return vdma ? 0 : -1; 809} 810 811int ide_id_dma_bug(ide_drive_t *drive) 812{ 813 struct hd_driveid *id = drive->id; 814 815 if (id->field_valid & 4) { 816 if ((id->dma_ultra >> 8) && (id->dma_mword >> 8)) 817 goto err_out; 818 } else if (id->field_valid & 2) { 819 if ((id->dma_mword >> 8) && (id->dma_1word >> 8)) 820 goto err_out; 821 } 822 return 0; 823err_out: 824 printk(KERN_ERR "%s: bad DMA info in identify block\n", drive->name); 825 return 1; 826} 827 828int ide_set_dma(ide_drive_t *drive) 829{ 830 ide_hwif_t *hwif = drive->hwif; 831 int rc; 832 833 /* 834 * Force DMAing for the beginning of the check. 835 * Some chipsets appear to do interesting 836 * things, if not checked and cleared. 837 * PARANOIA!!! 838 */ 839 hwif->dma_off_quietly(drive); 840 841 rc = ide_dma_check(drive); 842 if (rc) 843 return rc; 844 845 return hwif->ide_dma_on(drive); 846} 847 848#ifdef CONFIG_BLK_DEV_IDEDMA_PCI 849void ide_dma_lost_irq (ide_drive_t *drive) 850{ 851 printk("%s: DMA interrupt recovery\n", drive->name); 852} 853 854EXPORT_SYMBOL(ide_dma_lost_irq); 855 856void ide_dma_timeout (ide_drive_t *drive) 857{ 858 ide_hwif_t *hwif = HWIF(drive); 859 860 printk(KERN_ERR "%s: timeout waiting for DMA\n", drive->name); 861 862 if (hwif->ide_dma_test_irq(drive)) 863 return; 864 865 hwif->ide_dma_end(drive); 866} 867 868EXPORT_SYMBOL(ide_dma_timeout); 869 870static void ide_release_dma_engine(ide_hwif_t *hwif) 871{ 872 if (hwif->dmatable_cpu) { 873 pci_free_consistent(hwif->pci_dev, 874 PRD_ENTRIES * PRD_BYTES, 875 hwif->dmatable_cpu, 876 hwif->dmatable_dma); 877 hwif->dmatable_cpu = NULL; 878 } 879} 880 881static int ide_release_iomio_dma(ide_hwif_t *hwif) 882{ 883 release_region(hwif->dma_base, 8); 884 if (hwif->extra_ports) 885 release_region(hwif->extra_base, hwif->extra_ports); 886 return 1; 887} 888 889/* 890 * Needed for allowing full modular support of ide-driver 891 */ 892int ide_release_dma(ide_hwif_t *hwif) 893{ 894 ide_release_dma_engine(hwif); 895 896 if (hwif->mmio) 897 return 1; 898 else 899 return ide_release_iomio_dma(hwif); 900} 901 902static int ide_allocate_dma_engine(ide_hwif_t *hwif) 903{ 904 hwif->dmatable_cpu = pci_alloc_consistent(hwif->pci_dev, 905 PRD_ENTRIES * PRD_BYTES, 906 &hwif->dmatable_dma); 907 908 if (hwif->dmatable_cpu) 909 return 0; 910 911 printk(KERN_ERR "%s: -- Error, unable to allocate DMA table.\n", 912 hwif->cds->name); 913 914 return 1; 915} 916 917static int ide_mapped_mmio_dma(ide_hwif_t *hwif, unsigned long base, unsigned int ports) 918{ 919 printk(KERN_INFO " %s: MMIO-DMA ", hwif->name); 920 921 return 0; 922} 923 924static int ide_iomio_dma(ide_hwif_t *hwif, unsigned long base, unsigned int ports) 925{ 926 printk(KERN_INFO " %s: BM-DMA at 0x%04lx-0x%04lx", 927 hwif->name, base, base + ports - 1); 928 929 if (!request_region(base, ports, hwif->name)) { 930 printk(" -- Error, ports in use.\n"); 931 return 1; 932 } 933 934 if (hwif->cds->extra) { 935 hwif->extra_base = base + (hwif->channel ? 8 : 16); 936 937 if (!hwif->mate || !hwif->mate->extra_ports) { 938 if (!request_region(hwif->extra_base, 939 hwif->cds->extra, hwif->cds->name)) { 940 printk(" -- Error, extra ports in use.\n"); 941 release_region(base, ports); 942 return 1; 943 } 944 hwif->extra_ports = hwif->cds->extra; 945 } 946 } 947 948 return 0; 949} 950 951static int ide_dma_iobase(ide_hwif_t *hwif, unsigned long base, unsigned int ports) 952{ 953 if (hwif->mmio) 954 return ide_mapped_mmio_dma(hwif, base,ports); 955 956 return ide_iomio_dma(hwif, base, ports); 957} 958 959void ide_setup_dma(ide_hwif_t *hwif, unsigned long base, unsigned num_ports) 960{ 961 if (ide_dma_iobase(hwif, base, num_ports)) 962 return; 963 964 if (ide_allocate_dma_engine(hwif)) { 965 ide_release_dma(hwif); 966 return; 967 } 968 969 hwif->dma_base = base; 970 971 if (!(hwif->dma_command)) 972 hwif->dma_command = hwif->dma_base; 973 if (!(hwif->dma_vendor1)) 974 hwif->dma_vendor1 = (hwif->dma_base + 1); 975 if (!(hwif->dma_status)) 976 hwif->dma_status = (hwif->dma_base + 2); 977 if (!(hwif->dma_vendor3)) 978 hwif->dma_vendor3 = (hwif->dma_base + 3); 979 if (!(hwif->dma_prdtable)) 980 hwif->dma_prdtable = (hwif->dma_base + 4); 981 982 if (!hwif->dma_off_quietly) 983 hwif->dma_off_quietly = &ide_dma_off_quietly; 984 if (!hwif->dma_host_off) 985 hwif->dma_host_off = &ide_dma_host_off; 986 if (!hwif->ide_dma_on) 987 hwif->ide_dma_on = &__ide_dma_on; 988 if (!hwif->dma_host_on) 989 hwif->dma_host_on = &ide_dma_host_on; 990 if (!hwif->dma_setup) 991 hwif->dma_setup = &ide_dma_setup; 992 if (!hwif->dma_exec_cmd) 993 hwif->dma_exec_cmd = &ide_dma_exec_cmd; 994 if (!hwif->dma_start) 995 hwif->dma_start = &ide_dma_start; 996 if (!hwif->ide_dma_end) 997 hwif->ide_dma_end = &__ide_dma_end; 998 if (!hwif->ide_dma_test_irq) 999 hwif->ide_dma_test_irq = &__ide_dma_test_irq; 1000 if (!hwif->dma_timeout) 1001 hwif->dma_timeout = &ide_dma_timeout; 1002 if (!hwif->dma_lost_irq) 1003 hwif->dma_lost_irq = &ide_dma_lost_irq; 1004 1005 if (hwif->chipset != ide_trm290) { 1006 u8 dma_stat = hwif->INB(hwif->dma_status); 1007 printk(", BIOS settings: %s:%s, %s:%s", 1008 hwif->drives[0].name, (dma_stat & 0x20) ? "DMA" : "pio", 1009 hwif->drives[1].name, (dma_stat & 0x40) ? "DMA" : "pio"); 1010 } 1011 printk("\n"); 1012} 1013 1014EXPORT_SYMBOL_GPL(ide_setup_dma); 1015#endif /* CONFIG_BLK_DEV_IDEDMA_PCI */ 1016