siimage.c revision 35c9b4daf4c94b30e5cede597d98016ebf31b5ad
1/* 2 * Copyright (C) 2001-2002 Andre Hedrick <andre@linux-ide.org> 3 * Copyright (C) 2003 Red Hat 4 * Copyright (C) 2007-2008 MontaVista Software, Inc. 5 * Copyright (C) 2007-2008 Bartlomiej Zolnierkiewicz 6 * 7 * May be copied or modified under the terms of the GNU General Public License 8 * 9 * Documentation for CMD680: 10 * http://gkernel.sourceforge.net/specs/sii/sii-0680a-v1.31.pdf.bz2 11 * 12 * Documentation for SiI 3112: 13 * http://gkernel.sourceforge.net/specs/sii/3112A_SiI-DS-0095-B2.pdf.bz2 14 * 15 * Errata and other documentation only available under NDA. 16 * 17 * 18 * FAQ Items: 19 * If you are using Marvell SATA-IDE adapters with Maxtor drives 20 * ensure the system is set up for ATA100/UDMA5, not UDMA6. 21 * 22 * If you are using WD drives with SATA bridges you must set the 23 * drive to "Single". "Master" will hang. 24 * 25 * If you have strange problems with nVidia chipset systems please 26 * see the SI support documentation and update your system BIOS 27 * if necessary 28 * 29 * The Dell DRAC4 has some interesting features including effectively hot 30 * unplugging/replugging the virtual CD interface when the DRAC is reset. 31 * This often causes drivers/ide/siimage to panic but is ok with the rather 32 * smarter code in libata. 33 * 34 * TODO: 35 * - IORDY fixes 36 * - VDMA support 37 */ 38 39#include <linux/types.h> 40#include <linux/module.h> 41#include <linux/pci.h> 42#include <linux/ide.h> 43#include <linux/init.h> 44#include <linux/io.h> 45 46#define DRV_NAME "siimage" 47 48/** 49 * pdev_is_sata - check if device is SATA 50 * @pdev: PCI device to check 51 * 52 * Returns true if this is a SATA controller 53 */ 54 55static int pdev_is_sata(struct pci_dev *pdev) 56{ 57#ifdef CONFIG_BLK_DEV_IDE_SATA 58 switch (pdev->device) { 59 case PCI_DEVICE_ID_SII_3112: 60 case PCI_DEVICE_ID_SII_1210SA: 61 return 1; 62 case PCI_DEVICE_ID_SII_680: 63 return 0; 64 } 65 BUG(); 66#endif 67 return 0; 68} 69 70/** 71 * is_sata - check if hwif is SATA 72 * @hwif: interface to check 73 * 74 * Returns true if this is a SATA controller 75 */ 76 77static inline int is_sata(ide_hwif_t *hwif) 78{ 79 return pdev_is_sata(to_pci_dev(hwif->dev)); 80} 81 82/** 83 * siimage_selreg - return register base 84 * @hwif: interface 85 * @r: config offset 86 * 87 * Turn a config register offset into the right address in either 88 * PCI space or MMIO space to access the control register in question 89 * Thankfully this is a configuration operation, so isn't performance 90 * critical. 91 */ 92 93static unsigned long siimage_selreg(ide_hwif_t *hwif, int r) 94{ 95 unsigned long base = (unsigned long)hwif->hwif_data; 96 97 base += 0xA0 + r; 98 if (hwif->host_flags & IDE_HFLAG_MMIO) 99 base += hwif->channel << 6; 100 else 101 base += hwif->channel << 4; 102 return base; 103} 104 105/** 106 * siimage_seldev - return register base 107 * @hwif: interface 108 * @r: config offset 109 * 110 * Turn a config register offset into the right address in either 111 * PCI space or MMIO space to access the control register in question 112 * including accounting for the unit shift. 113 */ 114 115static inline unsigned long siimage_seldev(ide_drive_t *drive, int r) 116{ 117 ide_hwif_t *hwif = drive->hwif; 118 unsigned long base = (unsigned long)hwif->hwif_data; 119 u8 unit = drive->dn & 1; 120 121 base += 0xA0 + r; 122 if (hwif->host_flags & IDE_HFLAG_MMIO) 123 base += hwif->channel << 6; 124 else 125 base += hwif->channel << 4; 126 base |= unit << unit; 127 return base; 128} 129 130static u8 sil_ioread8(struct pci_dev *dev, unsigned long addr) 131{ 132 struct ide_host *host = pci_get_drvdata(dev); 133 u8 tmp = 0; 134 135 if (host->host_priv) 136 tmp = readb((void __iomem *)addr); 137 else 138 pci_read_config_byte(dev, addr, &tmp); 139 140 return tmp; 141} 142 143static u16 sil_ioread16(struct pci_dev *dev, unsigned long addr) 144{ 145 struct ide_host *host = pci_get_drvdata(dev); 146 u16 tmp = 0; 147 148 if (host->host_priv) 149 tmp = readw((void __iomem *)addr); 150 else 151 pci_read_config_word(dev, addr, &tmp); 152 153 return tmp; 154} 155 156static void sil_iowrite8(struct pci_dev *dev, u8 val, unsigned long addr) 157{ 158 struct ide_host *host = pci_get_drvdata(dev); 159 160 if (host->host_priv) 161 writeb(val, (void __iomem *)addr); 162 else 163 pci_write_config_byte(dev, addr, val); 164} 165 166static void sil_iowrite16(struct pci_dev *dev, u16 val, unsigned long addr) 167{ 168 struct ide_host *host = pci_get_drvdata(dev); 169 170 if (host->host_priv) 171 writew(val, (void __iomem *)addr); 172 else 173 pci_write_config_word(dev, addr, val); 174} 175 176static void sil_iowrite32(struct pci_dev *dev, u32 val, unsigned long addr) 177{ 178 struct ide_host *host = pci_get_drvdata(dev); 179 180 if (host->host_priv) 181 writel(val, (void __iomem *)addr); 182 else 183 pci_write_config_dword(dev, addr, val); 184} 185 186/** 187 * sil_udma_filter - compute UDMA mask 188 * @drive: IDE device 189 * 190 * Compute the available UDMA speeds for the device on the interface. 191 * 192 * For the CMD680 this depends on the clocking mode (scsc), for the 193 * SI3112 SATA controller life is a bit simpler. 194 */ 195 196static u8 sil_pata_udma_filter(ide_drive_t *drive) 197{ 198 ide_hwif_t *hwif = drive->hwif; 199 struct pci_dev *dev = to_pci_dev(hwif->dev); 200 unsigned long base = (unsigned long)hwif->hwif_data; 201 u8 scsc, mask = 0; 202 203 base += (hwif->host_flags & IDE_HFLAG_MMIO) ? 0x4A : 0x8A; 204 205 scsc = sil_ioread8(dev, base); 206 207 switch (scsc & 0x30) { 208 case 0x10: /* 133 */ 209 mask = ATA_UDMA6; 210 break; 211 case 0x20: /* 2xPCI */ 212 mask = ATA_UDMA6; 213 break; 214 case 0x00: /* 100 */ 215 mask = ATA_UDMA5; 216 break; 217 default: /* Disabled ? */ 218 BUG(); 219 } 220 221 return mask; 222} 223 224static u8 sil_sata_udma_filter(ide_drive_t *drive) 225{ 226 char *m = (char *)&drive->id[ATA_ID_PROD]; 227 228 return strstr(m, "Maxtor") ? ATA_UDMA5 : ATA_UDMA6; 229} 230 231/** 232 * sil_set_pio_mode - set host controller for PIO mode 233 * @drive: drive 234 * @pio: PIO mode number 235 * 236 * Load the timing settings for this device mode into the 237 * controller. If we are in PIO mode 3 or 4 turn on IORDY 238 * monitoring (bit 9). The TF timing is bits 31:16 239 */ 240 241static void sil_set_pio_mode(ide_drive_t *drive, u8 pio) 242{ 243 static const u16 tf_speed[] = { 0x328a, 0x2283, 0x1281, 0x10c3, 0x10c1 }; 244 static const u16 data_speed[] = { 0x328a, 0x2283, 0x1104, 0x10c3, 0x10c1 }; 245 246 ide_hwif_t *hwif = drive->hwif; 247 struct pci_dev *dev = to_pci_dev(hwif->dev); 248 ide_drive_t *pair = ide_get_pair_dev(drive); 249 u32 speedt = 0; 250 u16 speedp = 0; 251 unsigned long addr = siimage_seldev(drive, 0x04); 252 unsigned long tfaddr = siimage_selreg(hwif, 0x02); 253 unsigned long base = (unsigned long)hwif->hwif_data; 254 u8 tf_pio = pio; 255 u8 mmio = (hwif->host_flags & IDE_HFLAG_MMIO) ? 1 : 0; 256 u8 addr_mask = hwif->channel ? (mmio ? 0xF4 : 0x84) 257 : (mmio ? 0xB4 : 0x80); 258 u8 mode = 0; 259 u8 unit = drive->dn & 1; 260 261 /* trim *taskfile* PIO to the slowest of the master/slave */ 262 if (pair) { 263 u8 pair_pio = ide_get_best_pio_mode(pair, 255, 4); 264 265 if (pair_pio < tf_pio) 266 tf_pio = pair_pio; 267 } 268 269 /* cheat for now and use the docs */ 270 speedp = data_speed[pio]; 271 speedt = tf_speed[tf_pio]; 272 273 sil_iowrite16(dev, speedp, addr); 274 sil_iowrite16(dev, speedt, tfaddr); 275 276 /* now set up IORDY */ 277 speedp = sil_ioread16(dev, tfaddr - 2); 278 speedp &= ~0x200; 279 if (pio > 2) 280 speedp |= 0x200; 281 sil_iowrite16(dev, speedp, tfaddr - 2); 282 283 mode = sil_ioread8(dev, base + addr_mask); 284 mode &= ~(unit ? 0x30 : 0x03); 285 mode |= unit ? 0x10 : 0x01; 286 sil_iowrite8(dev, mode, base + addr_mask); 287} 288 289/** 290 * sil_set_dma_mode - set host controller for DMA mode 291 * @drive: drive 292 * @speed: DMA mode 293 * 294 * Tune the SiI chipset for the desired DMA mode. 295 */ 296 297static void sil_set_dma_mode(ide_drive_t *drive, const u8 speed) 298{ 299 static const u8 ultra6[] = { 0x0F, 0x0B, 0x07, 0x05, 0x03, 0x02, 0x01 }; 300 static const u8 ultra5[] = { 0x0C, 0x07, 0x05, 0x04, 0x02, 0x01 }; 301 static const u16 dma[] = { 0x2208, 0x10C2, 0x10C1 }; 302 303 ide_hwif_t *hwif = drive->hwif; 304 struct pci_dev *dev = to_pci_dev(hwif->dev); 305 unsigned long base = (unsigned long)hwif->hwif_data; 306 u16 ultra = 0, multi = 0; 307 u8 mode = 0, unit = drive->dn & 1; 308 u8 mmio = (hwif->host_flags & IDE_HFLAG_MMIO) ? 1 : 0; 309 u8 scsc = 0, addr_mask = hwif->channel ? (mmio ? 0xF4 : 0x84) 310 : (mmio ? 0xB4 : 0x80); 311 unsigned long ma = siimage_seldev(drive, 0x08); 312 unsigned long ua = siimage_seldev(drive, 0x0C); 313 314 scsc = sil_ioread8 (dev, base + (mmio ? 0x4A : 0x8A)); 315 mode = sil_ioread8 (dev, base + addr_mask); 316 multi = sil_ioread16(dev, ma); 317 ultra = sil_ioread16(dev, ua); 318 319 mode &= ~(unit ? 0x30 : 0x03); 320 ultra &= ~0x3F; 321 scsc = ((scsc & 0x30) == 0x00) ? 0 : 1; 322 323 scsc = is_sata(hwif) ? 1 : scsc; 324 325 if (speed >= XFER_UDMA_0) { 326 multi = dma[2]; 327 ultra |= scsc ? ultra6[speed - XFER_UDMA_0] : 328 ultra5[speed - XFER_UDMA_0]; 329 mode |= unit ? 0x30 : 0x03; 330 } else { 331 multi = dma[speed - XFER_MW_DMA_0]; 332 mode |= unit ? 0x20 : 0x02; 333 } 334 335 sil_iowrite8 (dev, mode, base + addr_mask); 336 sil_iowrite16(dev, multi, ma); 337 sil_iowrite16(dev, ultra, ua); 338} 339 340/* returns 1 if dma irq issued, 0 otherwise */ 341static int siimage_io_dma_test_irq(ide_drive_t *drive) 342{ 343 ide_hwif_t *hwif = drive->hwif; 344 struct pci_dev *dev = to_pci_dev(hwif->dev); 345 u8 dma_altstat = 0; 346 unsigned long addr = siimage_selreg(hwif, 1); 347 348 /* return 1 if INTR asserted */ 349 if (inb(hwif->dma_base + ATA_DMA_STATUS) & 4) 350 return 1; 351 352 /* return 1 if Device INTR asserted */ 353 pci_read_config_byte(dev, addr, &dma_altstat); 354 if (dma_altstat & 8) 355 return 0; /* return 1; */ 356 357 return 0; 358} 359 360/** 361 * siimage_mmio_dma_test_irq - check we caused an IRQ 362 * @drive: drive we are testing 363 * 364 * Check if we caused an IDE DMA interrupt. We may also have caused 365 * SATA status interrupts, if so we clean them up and continue. 366 */ 367 368static int siimage_mmio_dma_test_irq(ide_drive_t *drive) 369{ 370 ide_hwif_t *hwif = drive->hwif; 371 unsigned long addr = siimage_selreg(hwif, 0x1); 372 void __iomem *sata_error_addr 373 = (void __iomem *)hwif->sata_scr[SATA_ERROR_OFFSET]; 374 375 if (sata_error_addr) { 376 unsigned long base = (unsigned long)hwif->hwif_data; 377 u32 ext_stat = readl((void __iomem *)(base + 0x10)); 378 u8 watchdog = 0; 379 380 if (ext_stat & ((hwif->channel) ? 0x40 : 0x10)) { 381 u32 sata_error = readl(sata_error_addr); 382 383 writel(sata_error, sata_error_addr); 384 watchdog = (sata_error & 0x00680000) ? 1 : 0; 385 printk(KERN_WARNING "%s: sata_error = 0x%08x, " 386 "watchdog = %d, %s\n", 387 drive->name, sata_error, watchdog, __func__); 388 } else 389 watchdog = (ext_stat & 0x8000) ? 1 : 0; 390 391 ext_stat >>= 16; 392 if (!(ext_stat & 0x0404) && !watchdog) 393 return 0; 394 } 395 396 /* return 1 if INTR asserted */ 397 if (readb((void __iomem *)(hwif->dma_base + ATA_DMA_STATUS)) & 4) 398 return 1; 399 400 /* return 1 if Device INTR asserted */ 401 if (readb((void __iomem *)addr) & 8) 402 return 0; /* return 1; */ 403 404 return 0; 405} 406 407static int siimage_dma_test_irq(ide_drive_t *drive) 408{ 409 if (drive->hwif->host_flags & IDE_HFLAG_MMIO) 410 return siimage_mmio_dma_test_irq(drive); 411 else 412 return siimage_io_dma_test_irq(drive); 413} 414 415/** 416 * sil_sata_reset_poll - wait for SATA reset 417 * @drive: drive we are resetting 418 * 419 * Poll the SATA phy and see whether it has come back from the dead 420 * yet. 421 */ 422 423static int sil_sata_reset_poll(ide_drive_t *drive) 424{ 425 ide_hwif_t *hwif = drive->hwif; 426 void __iomem *sata_status_addr 427 = (void __iomem *)hwif->sata_scr[SATA_STATUS_OFFSET]; 428 429 if (sata_status_addr) { 430 /* SATA Status is available only when in MMIO mode */ 431 u32 sata_stat = readl(sata_status_addr); 432 433 if ((sata_stat & 0x03) != 0x03) { 434 printk(KERN_WARNING "%s: reset phy dead, status=0x%08x\n", 435 hwif->name, sata_stat); 436 return -ENXIO; 437 } 438 } 439 440 return 0; 441} 442 443/** 444 * sil_sata_pre_reset - reset hook 445 * @drive: IDE device being reset 446 * 447 * For the SATA devices we need to handle recalibration/geometry 448 * differently 449 */ 450 451static void sil_sata_pre_reset(ide_drive_t *drive) 452{ 453 if (drive->media == ide_disk) { 454 drive->special.b.set_geometry = 0; 455 drive->special.b.recalibrate = 0; 456 } 457} 458 459/** 460 * init_chipset_siimage - set up an SI device 461 * @dev: PCI device 462 * 463 * Perform the initial PCI set up for this device. Attempt to switch 464 * to 133 MHz clocking if the system isn't already set up to do it. 465 */ 466 467static int init_chipset_siimage(struct pci_dev *dev) 468{ 469 struct ide_host *host = pci_get_drvdata(dev); 470 void __iomem *ioaddr = host->host_priv; 471 unsigned long base, scsc_addr; 472 u8 rev = dev->revision, tmp; 473 474 pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, rev ? 1 : 255); 475 476 if (ioaddr) 477 pci_set_master(dev); 478 479 base = (unsigned long)ioaddr; 480 481 if (ioaddr && pdev_is_sata(dev)) { 482 u32 tmp32, irq_mask; 483 484 /* make sure IDE0/1 interrupts are not masked */ 485 irq_mask = (1 << 22) | (1 << 23); 486 tmp32 = readl(ioaddr + 0x48); 487 if (tmp32 & irq_mask) { 488 tmp32 &= ~irq_mask; 489 writel(tmp32, ioaddr + 0x48); 490 readl(ioaddr + 0x48); /* flush */ 491 } 492 writel(0, ioaddr + 0x148); 493 writel(0, ioaddr + 0x1C8); 494 } 495 496 sil_iowrite8(dev, 0, base ? (base + 0xB4) : 0x80); 497 sil_iowrite8(dev, 0, base ? (base + 0xF4) : 0x84); 498 499 scsc_addr = base ? (base + 0x4A) : 0x8A; 500 tmp = sil_ioread8(dev, scsc_addr); 501 502 switch (tmp & 0x30) { 503 case 0x00: 504 /* On 100 MHz clocking, try and switch to 133 MHz */ 505 sil_iowrite8(dev, tmp | 0x10, scsc_addr); 506 break; 507 case 0x30: 508 /* Clocking is disabled, attempt to force 133MHz clocking. */ 509 sil_iowrite8(dev, tmp & ~0x20, scsc_addr); 510 case 0x10: 511 /* On 133Mhz clocking. */ 512 break; 513 case 0x20: 514 /* On PCIx2 clocking. */ 515 break; 516 } 517 518 tmp = sil_ioread8(dev, scsc_addr); 519 520 sil_iowrite8 (dev, 0x72, base + 0xA1); 521 sil_iowrite16(dev, 0x328A, base + 0xA2); 522 sil_iowrite32(dev, 0x62DD62DD, base + 0xA4); 523 sil_iowrite32(dev, 0x43924392, base + 0xA8); 524 sil_iowrite32(dev, 0x40094009, base + 0xAC); 525 sil_iowrite8 (dev, 0x72, base ? (base + 0xE1) : 0xB1); 526 sil_iowrite16(dev, 0x328A, base ? (base + 0xE2) : 0xB2); 527 sil_iowrite32(dev, 0x62DD62DD, base ? (base + 0xE4) : 0xB4); 528 sil_iowrite32(dev, 0x43924392, base ? (base + 0xE8) : 0xB8); 529 sil_iowrite32(dev, 0x40094009, base ? (base + 0xEC) : 0xBC); 530 531 if (base && pdev_is_sata(dev)) { 532 writel(0xFFFF0000, ioaddr + 0x108); 533 writel(0xFFFF0000, ioaddr + 0x188); 534 writel(0x00680000, ioaddr + 0x148); 535 writel(0x00680000, ioaddr + 0x1C8); 536 } 537 538 /* report the clocking mode of the controller */ 539 if (!pdev_is_sata(dev)) { 540 static const char *clk_str[] = 541 { "== 100", "== 133", "== 2X PCI", "DISABLED!" }; 542 543 tmp >>= 4; 544 printk(KERN_INFO DRV_NAME " %s: BASE CLOCK %s\n", 545 pci_name(dev), clk_str[tmp & 3]); 546 } 547 548 return 0; 549} 550 551/** 552 * init_mmio_iops_siimage - set up the iops for MMIO 553 * @hwif: interface to set up 554 * 555 * The basic setup here is fairly simple, we can use standard MMIO 556 * operations. However we do have to set the taskfile register offsets 557 * by hand as there isn't a standard defined layout for them this time. 558 * 559 * The hardware supports buffered taskfiles and also some rather nice 560 * extended PRD tables. For better SI3112 support use the libata driver 561 */ 562 563static void __devinit init_mmio_iops_siimage(ide_hwif_t *hwif) 564{ 565 struct pci_dev *dev = to_pci_dev(hwif->dev); 566 struct ide_host *host = pci_get_drvdata(dev); 567 void *addr = host->host_priv; 568 u8 ch = hwif->channel; 569 struct ide_io_ports *io_ports = &hwif->io_ports; 570 unsigned long base; 571 572 /* 573 * Fill in the basic hwif bits 574 */ 575 hwif->host_flags |= IDE_HFLAG_MMIO; 576 577 hwif->hwif_data = addr; 578 579 /* 580 * Now set up the hw. We have to do this ourselves as the 581 * MMIO layout isn't the same as the standard port based I/O. 582 */ 583 memset(io_ports, 0, sizeof(*io_ports)); 584 585 base = (unsigned long)addr; 586 if (ch) 587 base += 0xC0; 588 else 589 base += 0x80; 590 591 /* 592 * The buffered task file doesn't have status/control, so we 593 * can't currently use it sanely since we want to use LBA48 mode. 594 */ 595 io_ports->data_addr = base; 596 io_ports->error_addr = base + 1; 597 io_ports->nsect_addr = base + 2; 598 io_ports->lbal_addr = base + 3; 599 io_ports->lbam_addr = base + 4; 600 io_ports->lbah_addr = base + 5; 601 io_ports->device_addr = base + 6; 602 io_ports->status_addr = base + 7; 603 io_ports->ctl_addr = base + 10; 604 605 if (pdev_is_sata(dev)) { 606 base = (unsigned long)addr; 607 if (ch) 608 base += 0x80; 609 hwif->sata_scr[SATA_STATUS_OFFSET] = base + 0x104; 610 hwif->sata_scr[SATA_ERROR_OFFSET] = base + 0x108; 611 hwif->sata_scr[SATA_CONTROL_OFFSET] = base + 0x100; 612 } 613 614 hwif->irq = dev->irq; 615 616 hwif->dma_base = (unsigned long)addr + (ch ? 0x08 : 0x00); 617} 618 619static int is_dev_seagate_sata(ide_drive_t *drive) 620{ 621 const char *s = (const char *)&drive->id[ATA_ID_PROD]; 622 unsigned len = strnlen(s, ATA_ID_PROD_LEN); 623 624 if ((len > 4) && (!memcmp(s, "ST", 2))) 625 if ((!memcmp(s + len - 2, "AS", 2)) || 626 (!memcmp(s + len - 3, "ASL", 3))) { 627 printk(KERN_INFO "%s: applying pessimistic Seagate " 628 "errata fix\n", drive->name); 629 return 1; 630 } 631 632 return 0; 633} 634 635/** 636 * sil_quirkproc - post probe fixups 637 * @drive: drive 638 * 639 * Called after drive probe we use this to decide whether the 640 * Seagate fixup must be applied. This used to be in init_iops but 641 * that can occur before we know what drives are present. 642 */ 643 644static void sil_quirkproc(ide_drive_t *drive) 645{ 646 ide_hwif_t *hwif = drive->hwif; 647 648 /* Try and rise the rqsize */ 649 if (!is_sata(hwif) || !is_dev_seagate_sata(drive)) 650 hwif->rqsize = 128; 651} 652 653/** 654 * init_iops_siimage - set up iops 655 * @hwif: interface to set up 656 * 657 * Do the basic setup for the SIIMAGE hardware interface 658 * and then do the MMIO setup if we can. This is the first 659 * look in we get for setting up the hwif so that we 660 * can get the iops right before using them. 661 */ 662 663static void __devinit init_iops_siimage(ide_hwif_t *hwif) 664{ 665 struct pci_dev *dev = to_pci_dev(hwif->dev); 666 struct ide_host *host = pci_get_drvdata(dev); 667 668 hwif->hwif_data = NULL; 669 670 /* Pessimal until we finish probing */ 671 hwif->rqsize = 15; 672 673 if (host->host_priv) 674 init_mmio_iops_siimage(hwif); 675} 676 677/** 678 * sil_cable_detect - cable detection 679 * @hwif: interface to check 680 * 681 * Check for the presence of an ATA66 capable cable on the interface. 682 */ 683 684static u8 sil_cable_detect(ide_hwif_t *hwif) 685{ 686 struct pci_dev *dev = to_pci_dev(hwif->dev); 687 unsigned long addr = siimage_selreg(hwif, 0); 688 u8 ata66 = sil_ioread8(dev, addr); 689 690 return (ata66 & 0x01) ? ATA_CBL_PATA80 : ATA_CBL_PATA40; 691} 692 693static const struct ide_port_ops sil_pata_port_ops = { 694 .set_pio_mode = sil_set_pio_mode, 695 .set_dma_mode = sil_set_dma_mode, 696 .quirkproc = sil_quirkproc, 697 .udma_filter = sil_pata_udma_filter, 698 .cable_detect = sil_cable_detect, 699}; 700 701static const struct ide_port_ops sil_sata_port_ops = { 702 .set_pio_mode = sil_set_pio_mode, 703 .set_dma_mode = sil_set_dma_mode, 704 .reset_poll = sil_sata_reset_poll, 705 .pre_reset = sil_sata_pre_reset, 706 .quirkproc = sil_quirkproc, 707 .udma_filter = sil_sata_udma_filter, 708 .cable_detect = sil_cable_detect, 709}; 710 711static const struct ide_dma_ops sil_dma_ops = { 712 .dma_host_set = ide_dma_host_set, 713 .dma_setup = ide_dma_setup, 714 .dma_start = ide_dma_start, 715 .dma_end = ide_dma_end, 716 .dma_test_irq = siimage_dma_test_irq, 717 .dma_timer_expiry = ide_dma_sff_timer_expiry, 718 .dma_lost_irq = ide_dma_lost_irq, 719 .dma_sff_read_status = ide_dma_sff_read_status, 720}; 721 722#define DECLARE_SII_DEV(p_ops) \ 723 { \ 724 .name = DRV_NAME, \ 725 .init_chipset = init_chipset_siimage, \ 726 .init_iops = init_iops_siimage, \ 727 .port_ops = p_ops, \ 728 .dma_ops = &sil_dma_ops, \ 729 .pio_mask = ATA_PIO4, \ 730 .mwdma_mask = ATA_MWDMA2, \ 731 .udma_mask = ATA_UDMA6, \ 732 } 733 734static const struct ide_port_info siimage_chipsets[] __devinitdata = { 735 /* 0: SiI680 */ DECLARE_SII_DEV(&sil_pata_port_ops), 736 /* 1: SiI3112 */ DECLARE_SII_DEV(&sil_sata_port_ops) 737}; 738 739/** 740 * siimage_init_one - PCI layer discovery entry 741 * @dev: PCI device 742 * @id: ident table entry 743 * 744 * Called by the PCI code when it finds an SiI680 or SiI3112 controller. 745 * We then use the IDE PCI generic helper to do most of the work. 746 */ 747 748static int __devinit siimage_init_one(struct pci_dev *dev, 749 const struct pci_device_id *id) 750{ 751 void __iomem *ioaddr = NULL; 752 resource_size_t bar5 = pci_resource_start(dev, 5); 753 unsigned long barsize = pci_resource_len(dev, 5); 754 int rc; 755 struct ide_port_info d; 756 u8 idx = id->driver_data; 757 u8 BA5_EN; 758 759 d = siimage_chipsets[idx]; 760 761 if (idx) { 762 static int first = 1; 763 764 if (first) { 765 printk(KERN_INFO DRV_NAME ": For full SATA support you " 766 "should use the libata sata_sil module.\n"); 767 first = 0; 768 } 769 770 d.host_flags |= IDE_HFLAG_NO_ATAPI_DMA; 771 } 772 773 rc = pci_enable_device(dev); 774 if (rc) 775 return rc; 776 777 pci_read_config_byte(dev, 0x8A, &BA5_EN); 778 if ((BA5_EN & 0x01) || bar5) { 779 /* 780 * Drop back to PIO if we can't map the MMIO. Some systems 781 * seem to get terminally confused in the PCI spaces. 782 */ 783 if (!request_mem_region(bar5, barsize, d.name)) { 784 printk(KERN_WARNING DRV_NAME " %s: MMIO ports not " 785 "available\n", pci_name(dev)); 786 } else { 787 ioaddr = pci_ioremap_bar(dev, 5); 788 if (ioaddr == NULL) 789 release_mem_region(bar5, barsize); 790 } 791 } 792 793 rc = ide_pci_init_one(dev, &d, ioaddr); 794 if (rc) { 795 if (ioaddr) { 796 iounmap(ioaddr); 797 release_mem_region(bar5, barsize); 798 } 799 pci_disable_device(dev); 800 } 801 802 return rc; 803} 804 805static void __devexit siimage_remove(struct pci_dev *dev) 806{ 807 struct ide_host *host = pci_get_drvdata(dev); 808 void __iomem *ioaddr = host->host_priv; 809 810 ide_pci_remove(dev); 811 812 if (ioaddr) { 813 resource_size_t bar5 = pci_resource_start(dev, 5); 814 unsigned long barsize = pci_resource_len(dev, 5); 815 816 iounmap(ioaddr); 817 release_mem_region(bar5, barsize); 818 } 819 820 pci_disable_device(dev); 821} 822 823static const struct pci_device_id siimage_pci_tbl[] = { 824 { PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_680), 0 }, 825#ifdef CONFIG_BLK_DEV_IDE_SATA 826 { PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_3112), 1 }, 827 { PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_1210SA), 1 }, 828#endif 829 { 0, }, 830}; 831MODULE_DEVICE_TABLE(pci, siimage_pci_tbl); 832 833static struct pci_driver siimage_pci_driver = { 834 .name = "SiI_IDE", 835 .id_table = siimage_pci_tbl, 836 .probe = siimage_init_one, 837 .remove = __devexit_p(siimage_remove), 838 .suspend = ide_pci_suspend, 839 .resume = ide_pci_resume, 840}; 841 842static int __init siimage_ide_init(void) 843{ 844 return ide_pci_register_driver(&siimage_pci_driver); 845} 846 847static void __exit siimage_ide_exit(void) 848{ 849 pci_unregister_driver(&siimage_pci_driver); 850} 851 852module_init(siimage_ide_init); 853module_exit(siimage_ide_exit); 854 855MODULE_AUTHOR("Andre Hedrick, Alan Cox"); 856MODULE_DESCRIPTION("PCI driver module for SiI IDE"); 857MODULE_LICENSE("GPL"); 858