janz-ican3.c revision 0ae89beb283a0db5980d1d4781c7d7be2f2810d6
1/* 2 * Janz MODULbus VMOD-ICAN3 CAN Interface Driver 3 * 4 * Copyright (c) 2010 Ira W. Snyder <iws@ovro.caltech.edu> 5 * 6 * This program is free software; you can redistribute it and/or modify it 7 * under the terms of the GNU General Public License as published by the 8 * Free Software Foundation; either version 2 of the License, or (at your 9 * option) any later version. 10 */ 11 12#include <linux/kernel.h> 13#include <linux/module.h> 14#include <linux/interrupt.h> 15#include <linux/delay.h> 16#include <linux/platform_device.h> 17 18#include <linux/netdevice.h> 19#include <linux/can.h> 20#include <linux/can/dev.h> 21#include <linux/can/skb.h> 22#include <linux/can/error.h> 23 24#include <linux/mfd/janz.h> 25#include <asm/io.h> 26 27/* the DPM has 64k of memory, organized into 256x 256 byte pages */ 28#define DPM_NUM_PAGES 256 29#define DPM_PAGE_SIZE 256 30#define DPM_PAGE_ADDR(p) ((p) * DPM_PAGE_SIZE) 31 32/* JANZ ICAN3 "old-style" host interface queue page numbers */ 33#define QUEUE_OLD_CONTROL 0 34#define QUEUE_OLD_RB0 1 35#define QUEUE_OLD_RB1 2 36#define QUEUE_OLD_WB0 3 37#define QUEUE_OLD_WB1 4 38 39/* Janz ICAN3 "old-style" host interface control registers */ 40#define MSYNC_PEER 0x00 /* ICAN only */ 41#define MSYNC_LOCL 0x01 /* host only */ 42#define TARGET_RUNNING 0x02 43 44#define MSYNC_RB0 0x01 45#define MSYNC_RB1 0x02 46#define MSYNC_RBLW 0x04 47#define MSYNC_RB_MASK (MSYNC_RB0 | MSYNC_RB1) 48 49#define MSYNC_WB0 0x10 50#define MSYNC_WB1 0x20 51#define MSYNC_WBLW 0x40 52#define MSYNC_WB_MASK (MSYNC_WB0 | MSYNC_WB1) 53 54/* Janz ICAN3 "new-style" host interface queue page numbers */ 55#define QUEUE_TOHOST 5 56#define QUEUE_FROMHOST_MID 6 57#define QUEUE_FROMHOST_HIGH 7 58#define QUEUE_FROMHOST_LOW 8 59 60/* The first free page in the DPM is #9 */ 61#define DPM_FREE_START 9 62 63/* Janz ICAN3 "new-style" and "fast" host interface descriptor flags */ 64#define DESC_VALID 0x80 65#define DESC_WRAP 0x40 66#define DESC_INTERRUPT 0x20 67#define DESC_IVALID 0x10 68#define DESC_LEN(len) (len) 69 70/* Janz ICAN3 Firmware Messages */ 71#define MSG_CONNECTI 0x02 72#define MSG_DISCONNECT 0x03 73#define MSG_IDVERS 0x04 74#define MSG_MSGLOST 0x05 75#define MSG_NEWHOSTIF 0x08 76#define MSG_INQUIRY 0x0a 77#define MSG_SETAFILMASK 0x10 78#define MSG_INITFDPMQUEUE 0x11 79#define MSG_HWCONF 0x12 80#define MSG_FMSGLOST 0x15 81#define MSG_CEVTIND 0x37 82#define MSG_CBTRREQ 0x41 83#define MSG_COFFREQ 0x42 84#define MSG_CONREQ 0x43 85#define MSG_CCONFREQ 0x47 86 87/* 88 * Janz ICAN3 CAN Inquiry Message Types 89 * 90 * NOTE: there appears to be a firmware bug here. You must send 91 * NOTE: INQUIRY_STATUS and expect to receive an INQUIRY_EXTENDED 92 * NOTE: response. The controller never responds to a message with 93 * NOTE: the INQUIRY_EXTENDED subspec :( 94 */ 95#define INQUIRY_STATUS 0x00 96#define INQUIRY_TERMINATION 0x01 97#define INQUIRY_EXTENDED 0x04 98 99/* Janz ICAN3 CAN Set Acceptance Filter Mask Message Types */ 100#define SETAFILMASK_REJECT 0x00 101#define SETAFILMASK_FASTIF 0x02 102 103/* Janz ICAN3 CAN Hardware Configuration Message Types */ 104#define HWCONF_TERMINATE_ON 0x01 105#define HWCONF_TERMINATE_OFF 0x00 106 107/* Janz ICAN3 CAN Event Indication Message Types */ 108#define CEVTIND_EI 0x01 109#define CEVTIND_DOI 0x02 110#define CEVTIND_LOST 0x04 111#define CEVTIND_FULL 0x08 112#define CEVTIND_BEI 0x10 113 114#define CEVTIND_CHIP_SJA1000 0x02 115 116#define ICAN3_BUSERR_QUOTA_MAX 255 117 118/* Janz ICAN3 CAN Frame Conversion */ 119#define ICAN3_SNGL 0x02 120#define ICAN3_ECHO 0x10 121#define ICAN3_EFF_RTR 0x40 122#define ICAN3_SFF_RTR 0x10 123#define ICAN3_EFF 0x80 124 125#define ICAN3_CAN_TYPE_MASK 0x0f 126#define ICAN3_CAN_TYPE_SFF 0x00 127#define ICAN3_CAN_TYPE_EFF 0x01 128 129#define ICAN3_CAN_DLC_MASK 0x0f 130 131/* 132 * SJA1000 Status and Error Register Definitions 133 * 134 * Copied from drivers/net/can/sja1000/sja1000.h 135 */ 136 137/* status register content */ 138#define SR_BS 0x80 139#define SR_ES 0x40 140#define SR_TS 0x20 141#define SR_RS 0x10 142#define SR_TCS 0x08 143#define SR_TBS 0x04 144#define SR_DOS 0x02 145#define SR_RBS 0x01 146 147#define SR_CRIT (SR_BS|SR_ES) 148 149/* ECC register */ 150#define ECC_SEG 0x1F 151#define ECC_DIR 0x20 152#define ECC_ERR 6 153#define ECC_BIT 0x00 154#define ECC_FORM 0x40 155#define ECC_STUFF 0x80 156#define ECC_MASK 0xc0 157 158/* Number of buffers for use in the "new-style" host interface */ 159#define ICAN3_NEW_BUFFERS 16 160 161/* Number of buffers for use in the "fast" host interface */ 162#define ICAN3_TX_BUFFERS 512 163#define ICAN3_RX_BUFFERS 1024 164 165/* SJA1000 Clock Input */ 166#define ICAN3_CAN_CLOCK 8000000 167 168/* Driver Name */ 169#define DRV_NAME "janz-ican3" 170 171/* DPM Control Registers -- starts at offset 0x100 in the MODULbus registers */ 172struct ican3_dpm_control { 173 /* window address register */ 174 u8 window_address; 175 u8 unused1; 176 177 /* 178 * Read access: clear interrupt from microcontroller 179 * Write access: send interrupt to microcontroller 180 */ 181 u8 interrupt; 182 u8 unused2; 183 184 /* write-only: reset all hardware on the module */ 185 u8 hwreset; 186 u8 unused3; 187 188 /* write-only: generate an interrupt to the TPU */ 189 u8 tpuinterrupt; 190}; 191 192struct ican3_dev { 193 194 /* must be the first member */ 195 struct can_priv can; 196 197 /* CAN network device */ 198 struct net_device *ndev; 199 struct napi_struct napi; 200 201 /* Device for printing */ 202 struct device *dev; 203 204 /* module number */ 205 unsigned int num; 206 207 /* base address of registers and IRQ */ 208 struct janz_cmodio_onboard_regs __iomem *ctrl; 209 struct ican3_dpm_control __iomem *dpmctrl; 210 void __iomem *dpm; 211 int irq; 212 213 /* CAN bus termination status */ 214 struct completion termination_comp; 215 bool termination_enabled; 216 217 /* CAN bus error status registers */ 218 struct completion buserror_comp; 219 struct can_berr_counter bec; 220 221 /* old and new style host interface */ 222 unsigned int iftype; 223 224 /* queue for echo packets */ 225 struct sk_buff_head echoq; 226 227 /* 228 * Any function which changes the current DPM page must hold this 229 * lock while it is performing data accesses. This ensures that the 230 * function will not be preempted and end up reading data from a 231 * different DPM page than it expects. 232 */ 233 spinlock_t lock; 234 235 /* new host interface */ 236 unsigned int rx_int; 237 unsigned int rx_num; 238 unsigned int tx_num; 239 240 /* fast host interface */ 241 unsigned int fastrx_start; 242 unsigned int fastrx_num; 243 unsigned int fasttx_start; 244 unsigned int fasttx_num; 245 246 /* first free DPM page */ 247 unsigned int free_page; 248}; 249 250struct ican3_msg { 251 u8 control; 252 u8 spec; 253 __le16 len; 254 u8 data[252]; 255}; 256 257struct ican3_new_desc { 258 u8 control; 259 u8 pointer; 260}; 261 262struct ican3_fast_desc { 263 u8 control; 264 u8 command; 265 u8 data[14]; 266}; 267 268/* write to the window basic address register */ 269static inline void ican3_set_page(struct ican3_dev *mod, unsigned int page) 270{ 271 BUG_ON(page >= DPM_NUM_PAGES); 272 iowrite8(page, &mod->dpmctrl->window_address); 273} 274 275/* 276 * ICAN3 "old-style" host interface 277 */ 278 279/* 280 * Receive a message from the ICAN3 "old-style" firmware interface 281 * 282 * LOCKING: must hold mod->lock 283 * 284 * returns 0 on success, -ENOMEM when no message exists 285 */ 286static int ican3_old_recv_msg(struct ican3_dev *mod, struct ican3_msg *msg) 287{ 288 unsigned int mbox, mbox_page; 289 u8 locl, peer, xord; 290 291 /* get the MSYNC registers */ 292 ican3_set_page(mod, QUEUE_OLD_CONTROL); 293 peer = ioread8(mod->dpm + MSYNC_PEER); 294 locl = ioread8(mod->dpm + MSYNC_LOCL); 295 xord = locl ^ peer; 296 297 if ((xord & MSYNC_RB_MASK) == 0x00) { 298 dev_dbg(mod->dev, "no mbox for reading\n"); 299 return -ENOMEM; 300 } 301 302 /* find the first free mbox to read */ 303 if ((xord & MSYNC_RB_MASK) == MSYNC_RB_MASK) 304 mbox = (xord & MSYNC_RBLW) ? MSYNC_RB0 : MSYNC_RB1; 305 else 306 mbox = (xord & MSYNC_RB0) ? MSYNC_RB0 : MSYNC_RB1; 307 308 /* copy the message */ 309 mbox_page = (mbox == MSYNC_RB0) ? QUEUE_OLD_RB0 : QUEUE_OLD_RB1; 310 ican3_set_page(mod, mbox_page); 311 memcpy_fromio(msg, mod->dpm, sizeof(*msg)); 312 313 /* 314 * notify the firmware that the read buffer is available 315 * for it to fill again 316 */ 317 locl ^= mbox; 318 319 ican3_set_page(mod, QUEUE_OLD_CONTROL); 320 iowrite8(locl, mod->dpm + MSYNC_LOCL); 321 return 0; 322} 323 324/* 325 * Send a message through the "old-style" firmware interface 326 * 327 * LOCKING: must hold mod->lock 328 * 329 * returns 0 on success, -ENOMEM when no free space exists 330 */ 331static int ican3_old_send_msg(struct ican3_dev *mod, struct ican3_msg *msg) 332{ 333 unsigned int mbox, mbox_page; 334 u8 locl, peer, xord; 335 336 /* get the MSYNC registers */ 337 ican3_set_page(mod, QUEUE_OLD_CONTROL); 338 peer = ioread8(mod->dpm + MSYNC_PEER); 339 locl = ioread8(mod->dpm + MSYNC_LOCL); 340 xord = locl ^ peer; 341 342 if ((xord & MSYNC_WB_MASK) == MSYNC_WB_MASK) { 343 dev_err(mod->dev, "no mbox for writing\n"); 344 return -ENOMEM; 345 } 346 347 /* calculate a free mbox to use */ 348 mbox = (xord & MSYNC_WB0) ? MSYNC_WB1 : MSYNC_WB0; 349 350 /* copy the message to the DPM */ 351 mbox_page = (mbox == MSYNC_WB0) ? QUEUE_OLD_WB0 : QUEUE_OLD_WB1; 352 ican3_set_page(mod, mbox_page); 353 memcpy_toio(mod->dpm, msg, sizeof(*msg)); 354 355 locl ^= mbox; 356 if (mbox == MSYNC_WB1) 357 locl |= MSYNC_WBLW; 358 359 ican3_set_page(mod, QUEUE_OLD_CONTROL); 360 iowrite8(locl, mod->dpm + MSYNC_LOCL); 361 return 0; 362} 363 364/* 365 * ICAN3 "new-style" Host Interface Setup 366 */ 367 368static void ican3_init_new_host_interface(struct ican3_dev *mod) 369{ 370 struct ican3_new_desc desc; 371 unsigned long flags; 372 void __iomem *dst; 373 int i; 374 375 spin_lock_irqsave(&mod->lock, flags); 376 377 /* setup the internal datastructures for RX */ 378 mod->rx_num = 0; 379 mod->rx_int = 0; 380 381 /* tohost queue descriptors are in page 5 */ 382 ican3_set_page(mod, QUEUE_TOHOST); 383 dst = mod->dpm; 384 385 /* initialize the tohost (rx) queue descriptors: pages 9-24 */ 386 for (i = 0; i < ICAN3_NEW_BUFFERS; i++) { 387 desc.control = DESC_INTERRUPT | DESC_LEN(1); /* I L=1 */ 388 desc.pointer = mod->free_page; 389 390 /* set wrap flag on last buffer */ 391 if (i == ICAN3_NEW_BUFFERS - 1) 392 desc.control |= DESC_WRAP; 393 394 memcpy_toio(dst, &desc, sizeof(desc)); 395 dst += sizeof(desc); 396 mod->free_page++; 397 } 398 399 /* fromhost (tx) mid queue descriptors are in page 6 */ 400 ican3_set_page(mod, QUEUE_FROMHOST_MID); 401 dst = mod->dpm; 402 403 /* setup the internal datastructures for TX */ 404 mod->tx_num = 0; 405 406 /* initialize the fromhost mid queue descriptors: pages 25-40 */ 407 for (i = 0; i < ICAN3_NEW_BUFFERS; i++) { 408 desc.control = DESC_VALID | DESC_LEN(1); /* V L=1 */ 409 desc.pointer = mod->free_page; 410 411 /* set wrap flag on last buffer */ 412 if (i == ICAN3_NEW_BUFFERS - 1) 413 desc.control |= DESC_WRAP; 414 415 memcpy_toio(dst, &desc, sizeof(desc)); 416 dst += sizeof(desc); 417 mod->free_page++; 418 } 419 420 /* fromhost hi queue descriptors are in page 7 */ 421 ican3_set_page(mod, QUEUE_FROMHOST_HIGH); 422 dst = mod->dpm; 423 424 /* initialize only a single buffer in the fromhost hi queue (unused) */ 425 desc.control = DESC_VALID | DESC_WRAP | DESC_LEN(1); /* VW L=1 */ 426 desc.pointer = mod->free_page; 427 memcpy_toio(dst, &desc, sizeof(desc)); 428 mod->free_page++; 429 430 /* fromhost low queue descriptors are in page 8 */ 431 ican3_set_page(mod, QUEUE_FROMHOST_LOW); 432 dst = mod->dpm; 433 434 /* initialize only a single buffer in the fromhost low queue (unused) */ 435 desc.control = DESC_VALID | DESC_WRAP | DESC_LEN(1); /* VW L=1 */ 436 desc.pointer = mod->free_page; 437 memcpy_toio(dst, &desc, sizeof(desc)); 438 mod->free_page++; 439 440 spin_unlock_irqrestore(&mod->lock, flags); 441} 442 443/* 444 * ICAN3 Fast Host Interface Setup 445 */ 446 447static void ican3_init_fast_host_interface(struct ican3_dev *mod) 448{ 449 struct ican3_fast_desc desc; 450 unsigned long flags; 451 unsigned int addr; 452 void __iomem *dst; 453 int i; 454 455 spin_lock_irqsave(&mod->lock, flags); 456 457 /* save the start recv page */ 458 mod->fastrx_start = mod->free_page; 459 mod->fastrx_num = 0; 460 461 /* build a single fast tohost queue descriptor */ 462 memset(&desc, 0, sizeof(desc)); 463 desc.control = 0x00; 464 desc.command = 1; 465 466 /* build the tohost queue descriptor ring in memory */ 467 addr = 0; 468 for (i = 0; i < ICAN3_RX_BUFFERS; i++) { 469 470 /* set the wrap bit on the last buffer */ 471 if (i == ICAN3_RX_BUFFERS - 1) 472 desc.control |= DESC_WRAP; 473 474 /* switch to the correct page */ 475 ican3_set_page(mod, mod->free_page); 476 477 /* copy the descriptor to the DPM */ 478 dst = mod->dpm + addr; 479 memcpy_toio(dst, &desc, sizeof(desc)); 480 addr += sizeof(desc); 481 482 /* move to the next page if necessary */ 483 if (addr >= DPM_PAGE_SIZE) { 484 addr = 0; 485 mod->free_page++; 486 } 487 } 488 489 /* make sure we page-align the next queue */ 490 if (addr != 0) 491 mod->free_page++; 492 493 /* save the start xmit page */ 494 mod->fasttx_start = mod->free_page; 495 mod->fasttx_num = 0; 496 497 /* build a single fast fromhost queue descriptor */ 498 memset(&desc, 0, sizeof(desc)); 499 desc.control = DESC_VALID; 500 desc.command = 1; 501 502 /* build the fromhost queue descriptor ring in memory */ 503 addr = 0; 504 for (i = 0; i < ICAN3_TX_BUFFERS; i++) { 505 506 /* set the wrap bit on the last buffer */ 507 if (i == ICAN3_TX_BUFFERS - 1) 508 desc.control |= DESC_WRAP; 509 510 /* switch to the correct page */ 511 ican3_set_page(mod, mod->free_page); 512 513 /* copy the descriptor to the DPM */ 514 dst = mod->dpm + addr; 515 memcpy_toio(dst, &desc, sizeof(desc)); 516 addr += sizeof(desc); 517 518 /* move to the next page if necessary */ 519 if (addr >= DPM_PAGE_SIZE) { 520 addr = 0; 521 mod->free_page++; 522 } 523 } 524 525 spin_unlock_irqrestore(&mod->lock, flags); 526} 527 528/* 529 * ICAN3 "new-style" Host Interface Message Helpers 530 */ 531 532/* 533 * LOCKING: must hold mod->lock 534 */ 535static int ican3_new_send_msg(struct ican3_dev *mod, struct ican3_msg *msg) 536{ 537 struct ican3_new_desc desc; 538 void __iomem *desc_addr = mod->dpm + (mod->tx_num * sizeof(desc)); 539 540 /* switch to the fromhost mid queue, and read the buffer descriptor */ 541 ican3_set_page(mod, QUEUE_FROMHOST_MID); 542 memcpy_fromio(&desc, desc_addr, sizeof(desc)); 543 544 if (!(desc.control & DESC_VALID)) { 545 dev_dbg(mod->dev, "%s: no free buffers\n", __func__); 546 return -ENOMEM; 547 } 548 549 /* switch to the data page, copy the data */ 550 ican3_set_page(mod, desc.pointer); 551 memcpy_toio(mod->dpm, msg, sizeof(*msg)); 552 553 /* switch back to the descriptor, set the valid bit, write it back */ 554 ican3_set_page(mod, QUEUE_FROMHOST_MID); 555 desc.control ^= DESC_VALID; 556 memcpy_toio(desc_addr, &desc, sizeof(desc)); 557 558 /* update the tx number */ 559 mod->tx_num = (desc.control & DESC_WRAP) ? 0 : (mod->tx_num + 1); 560 return 0; 561} 562 563/* 564 * LOCKING: must hold mod->lock 565 */ 566static int ican3_new_recv_msg(struct ican3_dev *mod, struct ican3_msg *msg) 567{ 568 struct ican3_new_desc desc; 569 void __iomem *desc_addr = mod->dpm + (mod->rx_num * sizeof(desc)); 570 571 /* switch to the tohost queue, and read the buffer descriptor */ 572 ican3_set_page(mod, QUEUE_TOHOST); 573 memcpy_fromio(&desc, desc_addr, sizeof(desc)); 574 575 if (!(desc.control & DESC_VALID)) { 576 dev_dbg(mod->dev, "%s: no buffers to recv\n", __func__); 577 return -ENOMEM; 578 } 579 580 /* switch to the data page, copy the data */ 581 ican3_set_page(mod, desc.pointer); 582 memcpy_fromio(msg, mod->dpm, sizeof(*msg)); 583 584 /* switch back to the descriptor, toggle the valid bit, write it back */ 585 ican3_set_page(mod, QUEUE_TOHOST); 586 desc.control ^= DESC_VALID; 587 memcpy_toio(desc_addr, &desc, sizeof(desc)); 588 589 /* update the rx number */ 590 mod->rx_num = (desc.control & DESC_WRAP) ? 0 : (mod->rx_num + 1); 591 return 0; 592} 593 594/* 595 * Message Send / Recv Helpers 596 */ 597 598static int ican3_send_msg(struct ican3_dev *mod, struct ican3_msg *msg) 599{ 600 unsigned long flags; 601 int ret; 602 603 spin_lock_irqsave(&mod->lock, flags); 604 605 if (mod->iftype == 0) 606 ret = ican3_old_send_msg(mod, msg); 607 else 608 ret = ican3_new_send_msg(mod, msg); 609 610 spin_unlock_irqrestore(&mod->lock, flags); 611 return ret; 612} 613 614static int ican3_recv_msg(struct ican3_dev *mod, struct ican3_msg *msg) 615{ 616 unsigned long flags; 617 int ret; 618 619 spin_lock_irqsave(&mod->lock, flags); 620 621 if (mod->iftype == 0) 622 ret = ican3_old_recv_msg(mod, msg); 623 else 624 ret = ican3_new_recv_msg(mod, msg); 625 626 spin_unlock_irqrestore(&mod->lock, flags); 627 return ret; 628} 629 630/* 631 * Quick Pre-constructed Messages 632 */ 633 634static int ican3_msg_connect(struct ican3_dev *mod) 635{ 636 struct ican3_msg msg; 637 638 memset(&msg, 0, sizeof(msg)); 639 msg.spec = MSG_CONNECTI; 640 msg.len = cpu_to_le16(0); 641 642 return ican3_send_msg(mod, &msg); 643} 644 645static int ican3_msg_disconnect(struct ican3_dev *mod) 646{ 647 struct ican3_msg msg; 648 649 memset(&msg, 0, sizeof(msg)); 650 msg.spec = MSG_DISCONNECT; 651 msg.len = cpu_to_le16(0); 652 653 return ican3_send_msg(mod, &msg); 654} 655 656static int ican3_msg_newhostif(struct ican3_dev *mod) 657{ 658 struct ican3_msg msg; 659 int ret; 660 661 memset(&msg, 0, sizeof(msg)); 662 msg.spec = MSG_NEWHOSTIF; 663 msg.len = cpu_to_le16(0); 664 665 /* If we're not using the old interface, switching seems bogus */ 666 WARN_ON(mod->iftype != 0); 667 668 ret = ican3_send_msg(mod, &msg); 669 if (ret) 670 return ret; 671 672 /* mark the module as using the new host interface */ 673 mod->iftype = 1; 674 return 0; 675} 676 677static int ican3_msg_fasthostif(struct ican3_dev *mod) 678{ 679 struct ican3_msg msg; 680 unsigned int addr; 681 682 memset(&msg, 0, sizeof(msg)); 683 msg.spec = MSG_INITFDPMQUEUE; 684 msg.len = cpu_to_le16(8); 685 686 /* write the tohost queue start address */ 687 addr = DPM_PAGE_ADDR(mod->fastrx_start); 688 msg.data[0] = addr & 0xff; 689 msg.data[1] = (addr >> 8) & 0xff; 690 msg.data[2] = (addr >> 16) & 0xff; 691 msg.data[3] = (addr >> 24) & 0xff; 692 693 /* write the fromhost queue start address */ 694 addr = DPM_PAGE_ADDR(mod->fasttx_start); 695 msg.data[4] = addr & 0xff; 696 msg.data[5] = (addr >> 8) & 0xff; 697 msg.data[6] = (addr >> 16) & 0xff; 698 msg.data[7] = (addr >> 24) & 0xff; 699 700 /* If we're not using the new interface yet, we cannot do this */ 701 WARN_ON(mod->iftype != 1); 702 703 return ican3_send_msg(mod, &msg); 704} 705 706/* 707 * Setup the CAN filter to either accept or reject all 708 * messages from the CAN bus. 709 */ 710static int ican3_set_id_filter(struct ican3_dev *mod, bool accept) 711{ 712 struct ican3_msg msg; 713 int ret; 714 715 /* Standard Frame Format */ 716 memset(&msg, 0, sizeof(msg)); 717 msg.spec = MSG_SETAFILMASK; 718 msg.len = cpu_to_le16(5); 719 msg.data[0] = 0x00; /* IDLo LSB */ 720 msg.data[1] = 0x00; /* IDLo MSB */ 721 msg.data[2] = 0xff; /* IDHi LSB */ 722 msg.data[3] = 0x07; /* IDHi MSB */ 723 724 /* accept all frames for fast host if, or reject all frames */ 725 msg.data[4] = accept ? SETAFILMASK_FASTIF : SETAFILMASK_REJECT; 726 727 ret = ican3_send_msg(mod, &msg); 728 if (ret) 729 return ret; 730 731 /* Extended Frame Format */ 732 memset(&msg, 0, sizeof(msg)); 733 msg.spec = MSG_SETAFILMASK; 734 msg.len = cpu_to_le16(13); 735 msg.data[0] = 0; /* MUX = 0 */ 736 msg.data[1] = 0x00; /* IDLo LSB */ 737 msg.data[2] = 0x00; 738 msg.data[3] = 0x00; 739 msg.data[4] = 0x20; /* IDLo MSB */ 740 msg.data[5] = 0xff; /* IDHi LSB */ 741 msg.data[6] = 0xff; 742 msg.data[7] = 0xff; 743 msg.data[8] = 0x3f; /* IDHi MSB */ 744 745 /* accept all frames for fast host if, or reject all frames */ 746 msg.data[9] = accept ? SETAFILMASK_FASTIF : SETAFILMASK_REJECT; 747 748 return ican3_send_msg(mod, &msg); 749} 750 751/* 752 * Bring the CAN bus online or offline 753 */ 754static int ican3_set_bus_state(struct ican3_dev *mod, bool on) 755{ 756 struct ican3_msg msg; 757 758 memset(&msg, 0, sizeof(msg)); 759 msg.spec = on ? MSG_CONREQ : MSG_COFFREQ; 760 msg.len = cpu_to_le16(0); 761 762 return ican3_send_msg(mod, &msg); 763} 764 765static int ican3_set_termination(struct ican3_dev *mod, bool on) 766{ 767 struct ican3_msg msg; 768 769 memset(&msg, 0, sizeof(msg)); 770 msg.spec = MSG_HWCONF; 771 msg.len = cpu_to_le16(2); 772 msg.data[0] = 0x00; 773 msg.data[1] = on ? HWCONF_TERMINATE_ON : HWCONF_TERMINATE_OFF; 774 775 return ican3_send_msg(mod, &msg); 776} 777 778static int ican3_send_inquiry(struct ican3_dev *mod, u8 subspec) 779{ 780 struct ican3_msg msg; 781 782 memset(&msg, 0, sizeof(msg)); 783 msg.spec = MSG_INQUIRY; 784 msg.len = cpu_to_le16(2); 785 msg.data[0] = subspec; 786 msg.data[1] = 0x00; 787 788 return ican3_send_msg(mod, &msg); 789} 790 791static int ican3_set_buserror(struct ican3_dev *mod, u8 quota) 792{ 793 struct ican3_msg msg; 794 795 memset(&msg, 0, sizeof(msg)); 796 msg.spec = MSG_CCONFREQ; 797 msg.len = cpu_to_le16(2); 798 msg.data[0] = 0x00; 799 msg.data[1] = quota; 800 801 return ican3_send_msg(mod, &msg); 802} 803 804/* 805 * ICAN3 to Linux CAN Frame Conversion 806 */ 807 808static void ican3_to_can_frame(struct ican3_dev *mod, 809 struct ican3_fast_desc *desc, 810 struct can_frame *cf) 811{ 812 if ((desc->command & ICAN3_CAN_TYPE_MASK) == ICAN3_CAN_TYPE_SFF) { 813 if (desc->data[1] & ICAN3_SFF_RTR) 814 cf->can_id |= CAN_RTR_FLAG; 815 816 cf->can_id |= desc->data[0] << 3; 817 cf->can_id |= (desc->data[1] & 0xe0) >> 5; 818 cf->can_dlc = get_can_dlc(desc->data[1] & ICAN3_CAN_DLC_MASK); 819 memcpy(cf->data, &desc->data[2], cf->can_dlc); 820 } else { 821 cf->can_dlc = get_can_dlc(desc->data[0] & ICAN3_CAN_DLC_MASK); 822 if (desc->data[0] & ICAN3_EFF_RTR) 823 cf->can_id |= CAN_RTR_FLAG; 824 825 if (desc->data[0] & ICAN3_EFF) { 826 cf->can_id |= CAN_EFF_FLAG; 827 cf->can_id |= desc->data[2] << 21; /* 28-21 */ 828 cf->can_id |= desc->data[3] << 13; /* 20-13 */ 829 cf->can_id |= desc->data[4] << 5; /* 12-5 */ 830 cf->can_id |= (desc->data[5] & 0xf8) >> 3; 831 } else { 832 cf->can_id |= desc->data[2] << 3; /* 10-3 */ 833 cf->can_id |= desc->data[3] >> 5; /* 2-0 */ 834 } 835 836 memcpy(cf->data, &desc->data[6], cf->can_dlc); 837 } 838} 839 840static void can_frame_to_ican3(struct ican3_dev *mod, 841 struct can_frame *cf, 842 struct ican3_fast_desc *desc) 843{ 844 /* clear out any stale data in the descriptor */ 845 memset(desc->data, 0, sizeof(desc->data)); 846 847 /* we always use the extended format, with the ECHO flag set */ 848 desc->command = ICAN3_CAN_TYPE_EFF; 849 desc->data[0] |= cf->can_dlc; 850 desc->data[1] |= ICAN3_ECHO; 851 852 /* support single transmission (no retries) mode */ 853 if (mod->can.ctrlmode & CAN_CTRLMODE_ONE_SHOT) 854 desc->data[1] |= ICAN3_SNGL; 855 856 if (cf->can_id & CAN_RTR_FLAG) 857 desc->data[0] |= ICAN3_EFF_RTR; 858 859 /* pack the id into the correct places */ 860 if (cf->can_id & CAN_EFF_FLAG) { 861 desc->data[0] |= ICAN3_EFF; 862 desc->data[2] = (cf->can_id & 0x1fe00000) >> 21; /* 28-21 */ 863 desc->data[3] = (cf->can_id & 0x001fe000) >> 13; /* 20-13 */ 864 desc->data[4] = (cf->can_id & 0x00001fe0) >> 5; /* 12-5 */ 865 desc->data[5] = (cf->can_id & 0x0000001f) << 3; /* 4-0 */ 866 } else { 867 desc->data[2] = (cf->can_id & 0x7F8) >> 3; /* bits 10-3 */ 868 desc->data[3] = (cf->can_id & 0x007) << 5; /* bits 2-0 */ 869 } 870 871 /* copy the data bits into the descriptor */ 872 memcpy(&desc->data[6], cf->data, cf->can_dlc); 873} 874 875/* 876 * Interrupt Handling 877 */ 878 879/* 880 * Handle an ID + Version message response from the firmware. We never generate 881 * this message in production code, but it is very useful when debugging to be 882 * able to display this message. 883 */ 884static void ican3_handle_idvers(struct ican3_dev *mod, struct ican3_msg *msg) 885{ 886 dev_dbg(mod->dev, "IDVERS response: %s\n", msg->data); 887} 888 889static void ican3_handle_msglost(struct ican3_dev *mod, struct ican3_msg *msg) 890{ 891 struct net_device *dev = mod->ndev; 892 struct net_device_stats *stats = &dev->stats; 893 struct can_frame *cf; 894 struct sk_buff *skb; 895 896 /* 897 * Report that communication messages with the microcontroller firmware 898 * are being lost. These are never CAN frames, so we do not generate an 899 * error frame for userspace 900 */ 901 if (msg->spec == MSG_MSGLOST) { 902 dev_err(mod->dev, "lost %d control messages\n", msg->data[0]); 903 return; 904 } 905 906 /* 907 * Oops, this indicates that we have lost messages in the fast queue, 908 * which are exclusively CAN messages. Our driver isn't reading CAN 909 * frames fast enough. 910 * 911 * We'll pretend that the SJA1000 told us that it ran out of buffer 912 * space, because there is not a better message for this. 913 */ 914 skb = alloc_can_err_skb(dev, &cf); 915 if (skb) { 916 cf->can_id |= CAN_ERR_CRTL; 917 cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW; 918 stats->rx_over_errors++; 919 stats->rx_errors++; 920 netif_rx(skb); 921 } 922} 923 924/* 925 * Handle CAN Event Indication Messages from the firmware 926 * 927 * The ICAN3 firmware provides the values of some SJA1000 registers when it 928 * generates this message. The code below is largely copied from the 929 * drivers/net/can/sja1000/sja1000.c file, and adapted as necessary 930 */ 931static int ican3_handle_cevtind(struct ican3_dev *mod, struct ican3_msg *msg) 932{ 933 struct net_device *dev = mod->ndev; 934 struct net_device_stats *stats = &dev->stats; 935 enum can_state state = mod->can.state; 936 u8 isrc, ecc, status, rxerr, txerr; 937 struct can_frame *cf; 938 struct sk_buff *skb; 939 940 /* we can only handle the SJA1000 part */ 941 if (msg->data[1] != CEVTIND_CHIP_SJA1000) { 942 dev_err(mod->dev, "unable to handle errors on non-SJA1000\n"); 943 return -ENODEV; 944 } 945 946 /* check the message length for sanity */ 947 if (le16_to_cpu(msg->len) < 6) { 948 dev_err(mod->dev, "error message too short\n"); 949 return -EINVAL; 950 } 951 952 isrc = msg->data[0]; 953 ecc = msg->data[2]; 954 status = msg->data[3]; 955 rxerr = msg->data[4]; 956 txerr = msg->data[5]; 957 958 /* 959 * This hardware lacks any support other than bus error messages to 960 * determine if packet transmission has failed. 961 * 962 * When TX errors happen, one echo skb needs to be dropped from the 963 * front of the queue. 964 * 965 * A small bit of code is duplicated here and below, to avoid error 966 * skb allocation when it will just be freed immediately. 967 */ 968 if (isrc == CEVTIND_BEI) { 969 int ret; 970 dev_dbg(mod->dev, "bus error interrupt\n"); 971 972 /* TX error */ 973 if (!(ecc & ECC_DIR)) { 974 kfree_skb(skb_dequeue(&mod->echoq)); 975 stats->tx_errors++; 976 } else { 977 stats->rx_errors++; 978 } 979 980 /* 981 * The controller automatically disables bus-error interrupts 982 * and therefore we must re-enable them. 983 */ 984 ret = ican3_set_buserror(mod, 1); 985 if (ret) { 986 dev_err(mod->dev, "unable to re-enable bus-error\n"); 987 return ret; 988 } 989 990 /* bus error reporting is off, return immediately */ 991 if (!(mod->can.ctrlmode & CAN_CTRLMODE_BERR_REPORTING)) 992 return 0; 993 } 994 995 skb = alloc_can_err_skb(dev, &cf); 996 if (skb == NULL) 997 return -ENOMEM; 998 999 /* data overrun interrupt */ 1000 if (isrc == CEVTIND_DOI || isrc == CEVTIND_LOST) { 1001 dev_dbg(mod->dev, "data overrun interrupt\n"); 1002 cf->can_id |= CAN_ERR_CRTL; 1003 cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW; 1004 stats->rx_over_errors++; 1005 stats->rx_errors++; 1006 } 1007 1008 /* error warning + passive interrupt */ 1009 if (isrc == CEVTIND_EI) { 1010 dev_dbg(mod->dev, "error warning + passive interrupt\n"); 1011 if (status & SR_BS) { 1012 state = CAN_STATE_BUS_OFF; 1013 cf->can_id |= CAN_ERR_BUSOFF; 1014 can_bus_off(dev); 1015 } else if (status & SR_ES) { 1016 if (rxerr >= 128 || txerr >= 128) 1017 state = CAN_STATE_ERROR_PASSIVE; 1018 else 1019 state = CAN_STATE_ERROR_WARNING; 1020 } else { 1021 state = CAN_STATE_ERROR_ACTIVE; 1022 } 1023 } 1024 1025 /* bus error interrupt */ 1026 if (isrc == CEVTIND_BEI) { 1027 mod->can.can_stats.bus_error++; 1028 cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR; 1029 1030 switch (ecc & ECC_MASK) { 1031 case ECC_BIT: 1032 cf->data[2] |= CAN_ERR_PROT_BIT; 1033 break; 1034 case ECC_FORM: 1035 cf->data[2] |= CAN_ERR_PROT_FORM; 1036 break; 1037 case ECC_STUFF: 1038 cf->data[2] |= CAN_ERR_PROT_STUFF; 1039 break; 1040 default: 1041 cf->data[2] |= CAN_ERR_PROT_UNSPEC; 1042 cf->data[3] = ecc & ECC_SEG; 1043 break; 1044 } 1045 1046 if (!(ecc & ECC_DIR)) 1047 cf->data[2] |= CAN_ERR_PROT_TX; 1048 1049 cf->data[6] = txerr; 1050 cf->data[7] = rxerr; 1051 } 1052 1053 if (state != mod->can.state && (state == CAN_STATE_ERROR_WARNING || 1054 state == CAN_STATE_ERROR_PASSIVE)) { 1055 cf->can_id |= CAN_ERR_CRTL; 1056 if (state == CAN_STATE_ERROR_WARNING) { 1057 mod->can.can_stats.error_warning++; 1058 cf->data[1] = (txerr > rxerr) ? 1059 CAN_ERR_CRTL_TX_WARNING : 1060 CAN_ERR_CRTL_RX_WARNING; 1061 } else { 1062 mod->can.can_stats.error_passive++; 1063 cf->data[1] = (txerr > rxerr) ? 1064 CAN_ERR_CRTL_TX_PASSIVE : 1065 CAN_ERR_CRTL_RX_PASSIVE; 1066 } 1067 1068 cf->data[6] = txerr; 1069 cf->data[7] = rxerr; 1070 } 1071 1072 mod->can.state = state; 1073 netif_rx(skb); 1074 return 0; 1075} 1076 1077static void ican3_handle_inquiry(struct ican3_dev *mod, struct ican3_msg *msg) 1078{ 1079 switch (msg->data[0]) { 1080 case INQUIRY_STATUS: 1081 case INQUIRY_EXTENDED: 1082 mod->bec.rxerr = msg->data[5]; 1083 mod->bec.txerr = msg->data[6]; 1084 complete(&mod->buserror_comp); 1085 break; 1086 case INQUIRY_TERMINATION: 1087 mod->termination_enabled = msg->data[6] & HWCONF_TERMINATE_ON; 1088 complete(&mod->termination_comp); 1089 break; 1090 default: 1091 dev_err(mod->dev, "received an unknown inquiry response\n"); 1092 break; 1093 } 1094} 1095 1096static void ican3_handle_unknown_message(struct ican3_dev *mod, 1097 struct ican3_msg *msg) 1098{ 1099 dev_warn(mod->dev, "received unknown message: spec 0x%.2x length %d\n", 1100 msg->spec, le16_to_cpu(msg->len)); 1101} 1102 1103/* 1104 * Handle a control message from the firmware 1105 */ 1106static void ican3_handle_message(struct ican3_dev *mod, struct ican3_msg *msg) 1107{ 1108 dev_dbg(mod->dev, "%s: modno %d spec 0x%.2x len %d bytes\n", __func__, 1109 mod->num, msg->spec, le16_to_cpu(msg->len)); 1110 1111 switch (msg->spec) { 1112 case MSG_IDVERS: 1113 ican3_handle_idvers(mod, msg); 1114 break; 1115 case MSG_MSGLOST: 1116 case MSG_FMSGLOST: 1117 ican3_handle_msglost(mod, msg); 1118 break; 1119 case MSG_CEVTIND: 1120 ican3_handle_cevtind(mod, msg); 1121 break; 1122 case MSG_INQUIRY: 1123 ican3_handle_inquiry(mod, msg); 1124 break; 1125 default: 1126 ican3_handle_unknown_message(mod, msg); 1127 break; 1128 } 1129} 1130 1131/* 1132 * The ican3 needs to store all echo skbs, and therefore cannot 1133 * use the generic infrastructure for this. 1134 */ 1135static void ican3_put_echo_skb(struct ican3_dev *mod, struct sk_buff *skb) 1136{ 1137 skb = can_create_echo_skb(skb); 1138 if (!skb) 1139 return; 1140 1141 /* save this skb for tx interrupt echo handling */ 1142 skb_queue_tail(&mod->echoq, skb); 1143} 1144 1145static unsigned int ican3_get_echo_skb(struct ican3_dev *mod) 1146{ 1147 struct sk_buff *skb = skb_dequeue(&mod->echoq); 1148 struct can_frame *cf; 1149 u8 dlc; 1150 1151 /* this should never trigger unless there is a driver bug */ 1152 if (!skb) { 1153 netdev_err(mod->ndev, "BUG: echo skb not occupied\n"); 1154 return 0; 1155 } 1156 1157 cf = (struct can_frame *)skb->data; 1158 dlc = cf->can_dlc; 1159 1160 /* check flag whether this packet has to be looped back */ 1161 if (skb->pkt_type != PACKET_LOOPBACK) { 1162 kfree_skb(skb); 1163 return dlc; 1164 } 1165 1166 skb->protocol = htons(ETH_P_CAN); 1167 skb->pkt_type = PACKET_BROADCAST; 1168 skb->ip_summed = CHECKSUM_UNNECESSARY; 1169 skb->dev = mod->ndev; 1170 netif_receive_skb(skb); 1171 return dlc; 1172} 1173 1174/* 1175 * Compare an skb with an existing echo skb 1176 * 1177 * This function will be used on devices which have a hardware loopback. 1178 * On these devices, this function can be used to compare a received skb 1179 * with the saved echo skbs so that the hardware echo skb can be dropped. 1180 * 1181 * Returns true if the skb's are identical, false otherwise. 1182 */ 1183static bool ican3_echo_skb_matches(struct ican3_dev *mod, struct sk_buff *skb) 1184{ 1185 struct can_frame *cf = (struct can_frame *)skb->data; 1186 struct sk_buff *echo_skb = skb_peek(&mod->echoq); 1187 struct can_frame *echo_cf; 1188 1189 if (!echo_skb) 1190 return false; 1191 1192 echo_cf = (struct can_frame *)echo_skb->data; 1193 if (cf->can_id != echo_cf->can_id) 1194 return false; 1195 1196 if (cf->can_dlc != echo_cf->can_dlc) 1197 return false; 1198 1199 return memcmp(cf->data, echo_cf->data, cf->can_dlc) == 0; 1200} 1201 1202/* 1203 * Check that there is room in the TX ring to transmit another skb 1204 * 1205 * LOCKING: must hold mod->lock 1206 */ 1207static bool ican3_txok(struct ican3_dev *mod) 1208{ 1209 struct ican3_fast_desc __iomem *desc; 1210 u8 control; 1211 1212 /* check that we have echo queue space */ 1213 if (skb_queue_len(&mod->echoq) >= ICAN3_TX_BUFFERS) 1214 return false; 1215 1216 /* copy the control bits of the descriptor */ 1217 ican3_set_page(mod, mod->fasttx_start + (mod->fasttx_num / 16)); 1218 desc = mod->dpm + ((mod->fasttx_num % 16) * sizeof(*desc)); 1219 control = ioread8(&desc->control); 1220 1221 /* if the control bits are not valid, then we have no more space */ 1222 if (!(control & DESC_VALID)) 1223 return false; 1224 1225 return true; 1226} 1227 1228/* 1229 * Receive one CAN frame from the hardware 1230 * 1231 * CONTEXT: must be called from user context 1232 */ 1233static int ican3_recv_skb(struct ican3_dev *mod) 1234{ 1235 struct net_device *ndev = mod->ndev; 1236 struct net_device_stats *stats = &ndev->stats; 1237 struct ican3_fast_desc desc; 1238 void __iomem *desc_addr; 1239 struct can_frame *cf; 1240 struct sk_buff *skb; 1241 unsigned long flags; 1242 1243 spin_lock_irqsave(&mod->lock, flags); 1244 1245 /* copy the whole descriptor */ 1246 ican3_set_page(mod, mod->fastrx_start + (mod->fastrx_num / 16)); 1247 desc_addr = mod->dpm + ((mod->fastrx_num % 16) * sizeof(desc)); 1248 memcpy_fromio(&desc, desc_addr, sizeof(desc)); 1249 1250 spin_unlock_irqrestore(&mod->lock, flags); 1251 1252 /* check that we actually have a CAN frame */ 1253 if (!(desc.control & DESC_VALID)) 1254 return -ENOBUFS; 1255 1256 /* allocate an skb */ 1257 skb = alloc_can_skb(ndev, &cf); 1258 if (unlikely(skb == NULL)) { 1259 stats->rx_dropped++; 1260 goto err_noalloc; 1261 } 1262 1263 /* convert the ICAN3 frame into Linux CAN format */ 1264 ican3_to_can_frame(mod, &desc, cf); 1265 1266 /* 1267 * If this is an ECHO frame received from the hardware loopback 1268 * feature, use the skb saved in the ECHO stack instead. This allows 1269 * the Linux CAN core to support CAN_RAW_RECV_OWN_MSGS correctly. 1270 * 1271 * Since this is a confirmation of a successfully transmitted packet 1272 * sent from this host, update the transmit statistics. 1273 * 1274 * Also, the netdevice queue needs to be allowed to send packets again. 1275 */ 1276 if (ican3_echo_skb_matches(mod, skb)) { 1277 stats->tx_packets++; 1278 stats->tx_bytes += ican3_get_echo_skb(mod); 1279 kfree_skb(skb); 1280 goto err_noalloc; 1281 } 1282 1283 /* update statistics, receive the skb */ 1284 stats->rx_packets++; 1285 stats->rx_bytes += cf->can_dlc; 1286 netif_receive_skb(skb); 1287 1288err_noalloc: 1289 /* toggle the valid bit and return the descriptor to the ring */ 1290 desc.control ^= DESC_VALID; 1291 1292 spin_lock_irqsave(&mod->lock, flags); 1293 1294 ican3_set_page(mod, mod->fastrx_start + (mod->fastrx_num / 16)); 1295 memcpy_toio(desc_addr, &desc, 1); 1296 1297 /* update the next buffer pointer */ 1298 mod->fastrx_num = (desc.control & DESC_WRAP) ? 0 1299 : (mod->fastrx_num + 1); 1300 1301 /* there are still more buffers to process */ 1302 spin_unlock_irqrestore(&mod->lock, flags); 1303 return 0; 1304} 1305 1306static int ican3_napi(struct napi_struct *napi, int budget) 1307{ 1308 struct ican3_dev *mod = container_of(napi, struct ican3_dev, napi); 1309 unsigned long flags; 1310 int received = 0; 1311 int ret; 1312 1313 /* process all communication messages */ 1314 while (true) { 1315 struct ican3_msg msg; 1316 ret = ican3_recv_msg(mod, &msg); 1317 if (ret) 1318 break; 1319 1320 ican3_handle_message(mod, &msg); 1321 } 1322 1323 /* process all CAN frames from the fast interface */ 1324 while (received < budget) { 1325 ret = ican3_recv_skb(mod); 1326 if (ret) 1327 break; 1328 1329 received++; 1330 } 1331 1332 /* We have processed all packets that the adapter had, but it 1333 * was less than our budget, stop polling */ 1334 if (received < budget) 1335 napi_complete(napi); 1336 1337 spin_lock_irqsave(&mod->lock, flags); 1338 1339 /* Wake up the transmit queue if necessary */ 1340 if (netif_queue_stopped(mod->ndev) && ican3_txok(mod)) 1341 netif_wake_queue(mod->ndev); 1342 1343 spin_unlock_irqrestore(&mod->lock, flags); 1344 1345 /* re-enable interrupt generation */ 1346 iowrite8(1 << mod->num, &mod->ctrl->int_enable); 1347 return received; 1348} 1349 1350static irqreturn_t ican3_irq(int irq, void *dev_id) 1351{ 1352 struct ican3_dev *mod = dev_id; 1353 u8 stat; 1354 1355 /* 1356 * The interrupt status register on this device reports interrupts 1357 * as zeroes instead of using ones like most other devices 1358 */ 1359 stat = ioread8(&mod->ctrl->int_disable) & (1 << mod->num); 1360 if (stat == (1 << mod->num)) 1361 return IRQ_NONE; 1362 1363 /* clear the MODULbus interrupt from the microcontroller */ 1364 ioread8(&mod->dpmctrl->interrupt); 1365 1366 /* disable interrupt generation, schedule the NAPI poller */ 1367 iowrite8(1 << mod->num, &mod->ctrl->int_disable); 1368 napi_schedule(&mod->napi); 1369 return IRQ_HANDLED; 1370} 1371 1372/* 1373 * Firmware reset, startup, and shutdown 1374 */ 1375 1376/* 1377 * Reset an ICAN module to its power-on state 1378 * 1379 * CONTEXT: no network device registered 1380 */ 1381static int ican3_reset_module(struct ican3_dev *mod) 1382{ 1383 unsigned long start; 1384 u8 runold, runnew; 1385 1386 /* disable interrupts so no more work is scheduled */ 1387 iowrite8(1 << mod->num, &mod->ctrl->int_disable); 1388 1389 /* the first unallocated page in the DPM is #9 */ 1390 mod->free_page = DPM_FREE_START; 1391 1392 ican3_set_page(mod, QUEUE_OLD_CONTROL); 1393 runold = ioread8(mod->dpm + TARGET_RUNNING); 1394 1395 /* reset the module */ 1396 iowrite8(0x00, &mod->dpmctrl->hwreset); 1397 1398 /* wait until the module has finished resetting and is running */ 1399 start = jiffies; 1400 do { 1401 ican3_set_page(mod, QUEUE_OLD_CONTROL); 1402 runnew = ioread8(mod->dpm + TARGET_RUNNING); 1403 if (runnew == (runold ^ 0xff)) 1404 return 0; 1405 1406 msleep(10); 1407 } while (time_before(jiffies, start + HZ / 4)); 1408 1409 dev_err(mod->dev, "failed to reset CAN module\n"); 1410 return -ETIMEDOUT; 1411} 1412 1413static void ican3_shutdown_module(struct ican3_dev *mod) 1414{ 1415 ican3_msg_disconnect(mod); 1416 ican3_reset_module(mod); 1417} 1418 1419/* 1420 * Startup an ICAN module, bringing it into fast mode 1421 */ 1422static int ican3_startup_module(struct ican3_dev *mod) 1423{ 1424 int ret; 1425 1426 ret = ican3_reset_module(mod); 1427 if (ret) { 1428 dev_err(mod->dev, "unable to reset module\n"); 1429 return ret; 1430 } 1431 1432 /* re-enable interrupts so we can send messages */ 1433 iowrite8(1 << mod->num, &mod->ctrl->int_enable); 1434 1435 ret = ican3_msg_connect(mod); 1436 if (ret) { 1437 dev_err(mod->dev, "unable to connect to module\n"); 1438 return ret; 1439 } 1440 1441 ican3_init_new_host_interface(mod); 1442 ret = ican3_msg_newhostif(mod); 1443 if (ret) { 1444 dev_err(mod->dev, "unable to switch to new-style interface\n"); 1445 return ret; 1446 } 1447 1448 /* default to "termination on" */ 1449 ret = ican3_set_termination(mod, true); 1450 if (ret) { 1451 dev_err(mod->dev, "unable to enable termination\n"); 1452 return ret; 1453 } 1454 1455 /* default to "bus errors enabled" */ 1456 ret = ican3_set_buserror(mod, 1); 1457 if (ret) { 1458 dev_err(mod->dev, "unable to set bus-error\n"); 1459 return ret; 1460 } 1461 1462 ican3_init_fast_host_interface(mod); 1463 ret = ican3_msg_fasthostif(mod); 1464 if (ret) { 1465 dev_err(mod->dev, "unable to switch to fast host interface\n"); 1466 return ret; 1467 } 1468 1469 ret = ican3_set_id_filter(mod, true); 1470 if (ret) { 1471 dev_err(mod->dev, "unable to set acceptance filter\n"); 1472 return ret; 1473 } 1474 1475 return 0; 1476} 1477 1478/* 1479 * CAN Network Device 1480 */ 1481 1482static int ican3_open(struct net_device *ndev) 1483{ 1484 struct ican3_dev *mod = netdev_priv(ndev); 1485 int ret; 1486 1487 /* open the CAN layer */ 1488 ret = open_candev(ndev); 1489 if (ret) { 1490 dev_err(mod->dev, "unable to start CAN layer\n"); 1491 return ret; 1492 } 1493 1494 /* bring the bus online */ 1495 ret = ican3_set_bus_state(mod, true); 1496 if (ret) { 1497 dev_err(mod->dev, "unable to set bus-on\n"); 1498 close_candev(ndev); 1499 return ret; 1500 } 1501 1502 /* start up the network device */ 1503 mod->can.state = CAN_STATE_ERROR_ACTIVE; 1504 netif_start_queue(ndev); 1505 1506 return 0; 1507} 1508 1509static int ican3_stop(struct net_device *ndev) 1510{ 1511 struct ican3_dev *mod = netdev_priv(ndev); 1512 int ret; 1513 1514 /* stop the network device xmit routine */ 1515 netif_stop_queue(ndev); 1516 mod->can.state = CAN_STATE_STOPPED; 1517 1518 /* bring the bus offline, stop receiving packets */ 1519 ret = ican3_set_bus_state(mod, false); 1520 if (ret) { 1521 dev_err(mod->dev, "unable to set bus-off\n"); 1522 return ret; 1523 } 1524 1525 /* drop all outstanding echo skbs */ 1526 skb_queue_purge(&mod->echoq); 1527 1528 /* close the CAN layer */ 1529 close_candev(ndev); 1530 return 0; 1531} 1532 1533static int ican3_xmit(struct sk_buff *skb, struct net_device *ndev) 1534{ 1535 struct ican3_dev *mod = netdev_priv(ndev); 1536 struct can_frame *cf = (struct can_frame *)skb->data; 1537 struct ican3_fast_desc desc; 1538 void __iomem *desc_addr; 1539 unsigned long flags; 1540 1541 if (can_dropped_invalid_skb(ndev, skb)) 1542 return NETDEV_TX_OK; 1543 1544 spin_lock_irqsave(&mod->lock, flags); 1545 1546 /* check that we can actually transmit */ 1547 if (!ican3_txok(mod)) { 1548 dev_err(mod->dev, "BUG: no free descriptors\n"); 1549 spin_unlock_irqrestore(&mod->lock, flags); 1550 return NETDEV_TX_BUSY; 1551 } 1552 1553 /* copy the control bits of the descriptor */ 1554 ican3_set_page(mod, mod->fasttx_start + (mod->fasttx_num / 16)); 1555 desc_addr = mod->dpm + ((mod->fasttx_num % 16) * sizeof(desc)); 1556 memset(&desc, 0, sizeof(desc)); 1557 memcpy_fromio(&desc, desc_addr, 1); 1558 1559 /* convert the Linux CAN frame into ICAN3 format */ 1560 can_frame_to_ican3(mod, cf, &desc); 1561 1562 /* 1563 * This hardware doesn't have TX-done notifications, so we'll try and 1564 * emulate it the best we can using ECHO skbs. Add the skb to the ECHO 1565 * stack. Upon packet reception, check if the ECHO skb and received 1566 * skb match, and use that to wake the queue. 1567 */ 1568 ican3_put_echo_skb(mod, skb); 1569 1570 /* 1571 * the programming manual says that you must set the IVALID bit, then 1572 * interrupt, then set the valid bit. Quite weird, but it seems to be 1573 * required for this to work 1574 */ 1575 desc.control |= DESC_IVALID; 1576 memcpy_toio(desc_addr, &desc, sizeof(desc)); 1577 1578 /* generate a MODULbus interrupt to the microcontroller */ 1579 iowrite8(0x01, &mod->dpmctrl->interrupt); 1580 1581 desc.control ^= DESC_VALID; 1582 memcpy_toio(desc_addr, &desc, sizeof(desc)); 1583 1584 /* update the next buffer pointer */ 1585 mod->fasttx_num = (desc.control & DESC_WRAP) ? 0 1586 : (mod->fasttx_num + 1); 1587 1588 /* if there is no free descriptor space, stop the transmit queue */ 1589 if (!ican3_txok(mod)) 1590 netif_stop_queue(ndev); 1591 1592 spin_unlock_irqrestore(&mod->lock, flags); 1593 return NETDEV_TX_OK; 1594} 1595 1596static const struct net_device_ops ican3_netdev_ops = { 1597 .ndo_open = ican3_open, 1598 .ndo_stop = ican3_stop, 1599 .ndo_start_xmit = ican3_xmit, 1600}; 1601 1602/* 1603 * Low-level CAN Device 1604 */ 1605 1606/* This structure was stolen from drivers/net/can/sja1000/sja1000.c */ 1607static const struct can_bittiming_const ican3_bittiming_const = { 1608 .name = DRV_NAME, 1609 .tseg1_min = 1, 1610 .tseg1_max = 16, 1611 .tseg2_min = 1, 1612 .tseg2_max = 8, 1613 .sjw_max = 4, 1614 .brp_min = 1, 1615 .brp_max = 64, 1616 .brp_inc = 1, 1617}; 1618 1619/* 1620 * This routine was stolen from drivers/net/can/sja1000/sja1000.c 1621 * 1622 * The bittiming register command for the ICAN3 just sets the bit timing 1623 * registers on the SJA1000 chip directly 1624 */ 1625static int ican3_set_bittiming(struct net_device *ndev) 1626{ 1627 struct ican3_dev *mod = netdev_priv(ndev); 1628 struct can_bittiming *bt = &mod->can.bittiming; 1629 struct ican3_msg msg; 1630 u8 btr0, btr1; 1631 1632 btr0 = ((bt->brp - 1) & 0x3f) | (((bt->sjw - 1) & 0x3) << 6); 1633 btr1 = ((bt->prop_seg + bt->phase_seg1 - 1) & 0xf) | 1634 (((bt->phase_seg2 - 1) & 0x7) << 4); 1635 if (mod->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES) 1636 btr1 |= 0x80; 1637 1638 memset(&msg, 0, sizeof(msg)); 1639 msg.spec = MSG_CBTRREQ; 1640 msg.len = cpu_to_le16(4); 1641 msg.data[0] = 0x00; 1642 msg.data[1] = 0x00; 1643 msg.data[2] = btr0; 1644 msg.data[3] = btr1; 1645 1646 return ican3_send_msg(mod, &msg); 1647} 1648 1649static int ican3_set_mode(struct net_device *ndev, enum can_mode mode) 1650{ 1651 struct ican3_dev *mod = netdev_priv(ndev); 1652 int ret; 1653 1654 if (mode != CAN_MODE_START) 1655 return -ENOTSUPP; 1656 1657 /* bring the bus online */ 1658 ret = ican3_set_bus_state(mod, true); 1659 if (ret) { 1660 dev_err(mod->dev, "unable to set bus-on\n"); 1661 return ret; 1662 } 1663 1664 /* start up the network device */ 1665 mod->can.state = CAN_STATE_ERROR_ACTIVE; 1666 1667 if (netif_queue_stopped(ndev)) 1668 netif_wake_queue(ndev); 1669 1670 return 0; 1671} 1672 1673static int ican3_get_berr_counter(const struct net_device *ndev, 1674 struct can_berr_counter *bec) 1675{ 1676 struct ican3_dev *mod = netdev_priv(ndev); 1677 int ret; 1678 1679 ret = ican3_send_inquiry(mod, INQUIRY_STATUS); 1680 if (ret) 1681 return ret; 1682 1683 ret = wait_for_completion_timeout(&mod->buserror_comp, HZ); 1684 if (ret == 0) { 1685 dev_info(mod->dev, "%s timed out\n", __func__); 1686 return -ETIMEDOUT; 1687 } 1688 1689 bec->rxerr = mod->bec.rxerr; 1690 bec->txerr = mod->bec.txerr; 1691 return 0; 1692} 1693 1694/* 1695 * Sysfs Attributes 1696 */ 1697 1698static ssize_t ican3_sysfs_show_term(struct device *dev, 1699 struct device_attribute *attr, 1700 char *buf) 1701{ 1702 struct ican3_dev *mod = netdev_priv(to_net_dev(dev)); 1703 int ret; 1704 1705 ret = ican3_send_inquiry(mod, INQUIRY_TERMINATION); 1706 if (ret) 1707 return ret; 1708 1709 ret = wait_for_completion_timeout(&mod->termination_comp, HZ); 1710 if (ret == 0) { 1711 dev_info(mod->dev, "%s timed out\n", __func__); 1712 return -ETIMEDOUT; 1713 } 1714 1715 return snprintf(buf, PAGE_SIZE, "%u\n", mod->termination_enabled); 1716} 1717 1718static ssize_t ican3_sysfs_set_term(struct device *dev, 1719 struct device_attribute *attr, 1720 const char *buf, size_t count) 1721{ 1722 struct ican3_dev *mod = netdev_priv(to_net_dev(dev)); 1723 unsigned long enable; 1724 int ret; 1725 1726 if (kstrtoul(buf, 0, &enable)) 1727 return -EINVAL; 1728 1729 ret = ican3_set_termination(mod, enable); 1730 if (ret) 1731 return ret; 1732 1733 return count; 1734} 1735 1736static DEVICE_ATTR(termination, S_IWUSR | S_IRUGO, ican3_sysfs_show_term, 1737 ican3_sysfs_set_term); 1738 1739static struct attribute *ican3_sysfs_attrs[] = { 1740 &dev_attr_termination.attr, 1741 NULL, 1742}; 1743 1744static struct attribute_group ican3_sysfs_attr_group = { 1745 .attrs = ican3_sysfs_attrs, 1746}; 1747 1748/* 1749 * PCI Subsystem 1750 */ 1751 1752static int ican3_probe(struct platform_device *pdev) 1753{ 1754 struct janz_platform_data *pdata; 1755 struct net_device *ndev; 1756 struct ican3_dev *mod; 1757 struct resource *res; 1758 struct device *dev; 1759 int ret; 1760 1761 pdata = dev_get_platdata(&pdev->dev); 1762 if (!pdata) 1763 return -ENXIO; 1764 1765 dev_dbg(&pdev->dev, "probe: module number %d\n", pdata->modno); 1766 1767 /* save the struct device for printing */ 1768 dev = &pdev->dev; 1769 1770 /* allocate the CAN device and private data */ 1771 ndev = alloc_candev(sizeof(*mod), 0); 1772 if (!ndev) { 1773 dev_err(dev, "unable to allocate CANdev\n"); 1774 ret = -ENOMEM; 1775 goto out_return; 1776 } 1777 1778 platform_set_drvdata(pdev, ndev); 1779 mod = netdev_priv(ndev); 1780 mod->ndev = ndev; 1781 mod->dev = &pdev->dev; 1782 mod->num = pdata->modno; 1783 netif_napi_add(ndev, &mod->napi, ican3_napi, ICAN3_RX_BUFFERS); 1784 skb_queue_head_init(&mod->echoq); 1785 spin_lock_init(&mod->lock); 1786 init_completion(&mod->termination_comp); 1787 init_completion(&mod->buserror_comp); 1788 1789 /* setup device-specific sysfs attributes */ 1790 ndev->sysfs_groups[0] = &ican3_sysfs_attr_group; 1791 1792 /* the first unallocated page in the DPM is 9 */ 1793 mod->free_page = DPM_FREE_START; 1794 1795 ndev->netdev_ops = &ican3_netdev_ops; 1796 ndev->flags |= IFF_ECHO; 1797 SET_NETDEV_DEV(ndev, &pdev->dev); 1798 1799 mod->can.clock.freq = ICAN3_CAN_CLOCK; 1800 mod->can.bittiming_const = &ican3_bittiming_const; 1801 mod->can.do_set_bittiming = ican3_set_bittiming; 1802 mod->can.do_set_mode = ican3_set_mode; 1803 mod->can.do_get_berr_counter = ican3_get_berr_counter; 1804 mod->can.ctrlmode_supported = CAN_CTRLMODE_3_SAMPLES 1805 | CAN_CTRLMODE_BERR_REPORTING 1806 | CAN_CTRLMODE_ONE_SHOT; 1807 1808 /* find our IRQ number */ 1809 mod->irq = platform_get_irq(pdev, 0); 1810 if (mod->irq < 0) { 1811 dev_err(dev, "IRQ line not found\n"); 1812 ret = -ENODEV; 1813 goto out_free_ndev; 1814 } 1815 1816 ndev->irq = mod->irq; 1817 1818 /* get access to the MODULbus registers for this module */ 1819 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 1820 if (!res) { 1821 dev_err(dev, "MODULbus registers not found\n"); 1822 ret = -ENODEV; 1823 goto out_free_ndev; 1824 } 1825 1826 mod->dpm = ioremap(res->start, resource_size(res)); 1827 if (!mod->dpm) { 1828 dev_err(dev, "MODULbus registers not ioremap\n"); 1829 ret = -ENOMEM; 1830 goto out_free_ndev; 1831 } 1832 1833 mod->dpmctrl = mod->dpm + DPM_PAGE_SIZE; 1834 1835 /* get access to the control registers for this module */ 1836 res = platform_get_resource(pdev, IORESOURCE_MEM, 1); 1837 if (!res) { 1838 dev_err(dev, "CONTROL registers not found\n"); 1839 ret = -ENODEV; 1840 goto out_iounmap_dpm; 1841 } 1842 1843 mod->ctrl = ioremap(res->start, resource_size(res)); 1844 if (!mod->ctrl) { 1845 dev_err(dev, "CONTROL registers not ioremap\n"); 1846 ret = -ENOMEM; 1847 goto out_iounmap_dpm; 1848 } 1849 1850 /* disable our IRQ, then hookup the IRQ handler */ 1851 iowrite8(1 << mod->num, &mod->ctrl->int_disable); 1852 ret = request_irq(mod->irq, ican3_irq, IRQF_SHARED, DRV_NAME, mod); 1853 if (ret) { 1854 dev_err(dev, "unable to request IRQ\n"); 1855 goto out_iounmap_ctrl; 1856 } 1857 1858 /* reset and initialize the CAN controller into fast mode */ 1859 napi_enable(&mod->napi); 1860 ret = ican3_startup_module(mod); 1861 if (ret) { 1862 dev_err(dev, "%s: unable to start CANdev\n", __func__); 1863 goto out_free_irq; 1864 } 1865 1866 /* register with the Linux CAN layer */ 1867 ret = register_candev(ndev); 1868 if (ret) { 1869 dev_err(dev, "%s: unable to register CANdev\n", __func__); 1870 goto out_free_irq; 1871 } 1872 1873 dev_info(dev, "module %d: registered CAN device\n", pdata->modno); 1874 return 0; 1875 1876out_free_irq: 1877 napi_disable(&mod->napi); 1878 iowrite8(1 << mod->num, &mod->ctrl->int_disable); 1879 free_irq(mod->irq, mod); 1880out_iounmap_ctrl: 1881 iounmap(mod->ctrl); 1882out_iounmap_dpm: 1883 iounmap(mod->dpm); 1884out_free_ndev: 1885 free_candev(ndev); 1886out_return: 1887 return ret; 1888} 1889 1890static int ican3_remove(struct platform_device *pdev) 1891{ 1892 struct net_device *ndev = platform_get_drvdata(pdev); 1893 struct ican3_dev *mod = netdev_priv(ndev); 1894 1895 /* unregister the netdevice, stop interrupts */ 1896 unregister_netdev(ndev); 1897 napi_disable(&mod->napi); 1898 iowrite8(1 << mod->num, &mod->ctrl->int_disable); 1899 free_irq(mod->irq, mod); 1900 1901 /* put the module into reset */ 1902 ican3_shutdown_module(mod); 1903 1904 /* unmap all registers */ 1905 iounmap(mod->ctrl); 1906 iounmap(mod->dpm); 1907 1908 free_candev(ndev); 1909 1910 return 0; 1911} 1912 1913static struct platform_driver ican3_driver = { 1914 .driver = { 1915 .name = DRV_NAME, 1916 .owner = THIS_MODULE, 1917 }, 1918 .probe = ican3_probe, 1919 .remove = ican3_remove, 1920}; 1921 1922module_platform_driver(ican3_driver); 1923 1924MODULE_AUTHOR("Ira W. Snyder <iws@ovro.caltech.edu>"); 1925MODULE_DESCRIPTION("Janz MODULbus VMOD-ICAN3 Driver"); 1926MODULE_LICENSE("GPL"); 1927MODULE_ALIAS("platform:janz-ican3"); 1928