e1000_82575.c revision f96a8a0b78548c0ec06b0b4b438db6ee895d67e9
1/******************************************************************************* 2 3 Intel(R) Gigabit Ethernet Linux driver 4 Copyright(c) 2007-2012 Intel Corporation. 5 6 This program is free software; you can redistribute it and/or modify it 7 under the terms and conditions of the GNU General Public License, 8 version 2, as published by the Free Software Foundation. 9 10 This program is distributed in the hope it will be useful, but WITHOUT 11 ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or 12 FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for 13 more details. 14 15 You should have received a copy of the GNU General Public License along with 16 this program; if not, write to the Free Software Foundation, Inc., 17 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. 18 19 The full GNU General Public License is included in this distribution in 20 the file called "COPYING". 21 22 Contact Information: 23 e1000-devel Mailing List <e1000-devel@lists.sourceforge.net> 24 Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 25 26*******************************************************************************/ 27 28/* e1000_82575 29 * e1000_82576 30 */ 31 32#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt 33 34#include <linux/types.h> 35#include <linux/if_ether.h> 36 37#include "e1000_mac.h" 38#include "e1000_82575.h" 39#include "e1000_i210.h" 40 41static s32 igb_get_invariants_82575(struct e1000_hw *); 42static s32 igb_acquire_phy_82575(struct e1000_hw *); 43static void igb_release_phy_82575(struct e1000_hw *); 44static s32 igb_acquire_nvm_82575(struct e1000_hw *); 45static void igb_release_nvm_82575(struct e1000_hw *); 46static s32 igb_check_for_link_82575(struct e1000_hw *); 47static s32 igb_get_cfg_done_82575(struct e1000_hw *); 48static s32 igb_init_hw_82575(struct e1000_hw *); 49static s32 igb_phy_hw_reset_sgmii_82575(struct e1000_hw *); 50static s32 igb_read_phy_reg_sgmii_82575(struct e1000_hw *, u32, u16 *); 51static s32 igb_read_phy_reg_82580(struct e1000_hw *, u32, u16 *); 52static s32 igb_write_phy_reg_82580(struct e1000_hw *, u32, u16); 53static s32 igb_reset_hw_82575(struct e1000_hw *); 54static s32 igb_reset_hw_82580(struct e1000_hw *); 55static s32 igb_set_d0_lplu_state_82575(struct e1000_hw *, bool); 56static s32 igb_set_d0_lplu_state_82580(struct e1000_hw *, bool); 57static s32 igb_set_d3_lplu_state_82580(struct e1000_hw *, bool); 58static s32 igb_setup_copper_link_82575(struct e1000_hw *); 59static s32 igb_setup_serdes_link_82575(struct e1000_hw *); 60static s32 igb_write_phy_reg_sgmii_82575(struct e1000_hw *, u32, u16); 61static void igb_clear_hw_cntrs_82575(struct e1000_hw *); 62static s32 igb_acquire_swfw_sync_82575(struct e1000_hw *, u16); 63static s32 igb_get_pcs_speed_and_duplex_82575(struct e1000_hw *, u16 *, 64 u16 *); 65static s32 igb_get_phy_id_82575(struct e1000_hw *); 66static void igb_release_swfw_sync_82575(struct e1000_hw *, u16); 67static bool igb_sgmii_active_82575(struct e1000_hw *); 68static s32 igb_reset_init_script_82575(struct e1000_hw *); 69static s32 igb_read_mac_addr_82575(struct e1000_hw *); 70static s32 igb_set_pcie_completion_timeout(struct e1000_hw *hw); 71static s32 igb_reset_mdicnfg_82580(struct e1000_hw *hw); 72static s32 igb_validate_nvm_checksum_82580(struct e1000_hw *hw); 73static s32 igb_update_nvm_checksum_82580(struct e1000_hw *hw); 74static s32 igb_validate_nvm_checksum_i350(struct e1000_hw *hw); 75static s32 igb_update_nvm_checksum_i350(struct e1000_hw *hw); 76static const u16 e1000_82580_rxpbs_table[] = 77 { 36, 72, 144, 1, 2, 4, 8, 16, 78 35, 70, 140 }; 79#define E1000_82580_RXPBS_TABLE_SIZE \ 80 (sizeof(e1000_82580_rxpbs_table)/sizeof(u16)) 81 82/** 83 * igb_sgmii_uses_mdio_82575 - Determine if I2C pins are for external MDIO 84 * @hw: pointer to the HW structure 85 * 86 * Called to determine if the I2C pins are being used for I2C or as an 87 * external MDIO interface since the two options are mutually exclusive. 88 **/ 89static bool igb_sgmii_uses_mdio_82575(struct e1000_hw *hw) 90{ 91 u32 reg = 0; 92 bool ext_mdio = false; 93 94 switch (hw->mac.type) { 95 case e1000_82575: 96 case e1000_82576: 97 reg = rd32(E1000_MDIC); 98 ext_mdio = !!(reg & E1000_MDIC_DEST); 99 break; 100 case e1000_82580: 101 case e1000_i350: 102 case e1000_i210: 103 case e1000_i211: 104 reg = rd32(E1000_MDICNFG); 105 ext_mdio = !!(reg & E1000_MDICNFG_EXT_MDIO); 106 break; 107 default: 108 break; 109 } 110 return ext_mdio; 111} 112 113static s32 igb_get_invariants_82575(struct e1000_hw *hw) 114{ 115 struct e1000_phy_info *phy = &hw->phy; 116 struct e1000_nvm_info *nvm = &hw->nvm; 117 struct e1000_mac_info *mac = &hw->mac; 118 struct e1000_dev_spec_82575 * dev_spec = &hw->dev_spec._82575; 119 u32 eecd; 120 s32 ret_val; 121 u16 size; 122 u32 ctrl_ext = 0; 123 124 switch (hw->device_id) { 125 case E1000_DEV_ID_82575EB_COPPER: 126 case E1000_DEV_ID_82575EB_FIBER_SERDES: 127 case E1000_DEV_ID_82575GB_QUAD_COPPER: 128 mac->type = e1000_82575; 129 break; 130 case E1000_DEV_ID_82576: 131 case E1000_DEV_ID_82576_NS: 132 case E1000_DEV_ID_82576_NS_SERDES: 133 case E1000_DEV_ID_82576_FIBER: 134 case E1000_DEV_ID_82576_SERDES: 135 case E1000_DEV_ID_82576_QUAD_COPPER: 136 case E1000_DEV_ID_82576_QUAD_COPPER_ET2: 137 case E1000_DEV_ID_82576_SERDES_QUAD: 138 mac->type = e1000_82576; 139 break; 140 case E1000_DEV_ID_82580_COPPER: 141 case E1000_DEV_ID_82580_FIBER: 142 case E1000_DEV_ID_82580_QUAD_FIBER: 143 case E1000_DEV_ID_82580_SERDES: 144 case E1000_DEV_ID_82580_SGMII: 145 case E1000_DEV_ID_82580_COPPER_DUAL: 146 case E1000_DEV_ID_DH89XXCC_SGMII: 147 case E1000_DEV_ID_DH89XXCC_SERDES: 148 case E1000_DEV_ID_DH89XXCC_BACKPLANE: 149 case E1000_DEV_ID_DH89XXCC_SFP: 150 mac->type = e1000_82580; 151 break; 152 case E1000_DEV_ID_I350_COPPER: 153 case E1000_DEV_ID_I350_FIBER: 154 case E1000_DEV_ID_I350_SERDES: 155 case E1000_DEV_ID_I350_SGMII: 156 mac->type = e1000_i350; 157 break; 158 case E1000_DEV_ID_I210_COPPER: 159 case E1000_DEV_ID_I210_COPPER_OEM1: 160 case E1000_DEV_ID_I210_COPPER_IT: 161 case E1000_DEV_ID_I210_FIBER: 162 case E1000_DEV_ID_I210_SERDES: 163 case E1000_DEV_ID_I210_SGMII: 164 mac->type = e1000_i210; 165 break; 166 case E1000_DEV_ID_I211_COPPER: 167 mac->type = e1000_i211; 168 break; 169 default: 170 return -E1000_ERR_MAC_INIT; 171 break; 172 } 173 174 /* Set media type */ 175 /* 176 * The 82575 uses bits 22:23 for link mode. The mode can be changed 177 * based on the EEPROM. We cannot rely upon device ID. There 178 * is no distinguishable difference between fiber and internal 179 * SerDes mode on the 82575. There can be an external PHY attached 180 * on the SGMII interface. For this, we'll set sgmii_active to true. 181 */ 182 phy->media_type = e1000_media_type_copper; 183 dev_spec->sgmii_active = false; 184 185 ctrl_ext = rd32(E1000_CTRL_EXT); 186 switch (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) { 187 case E1000_CTRL_EXT_LINK_MODE_SGMII: 188 dev_spec->sgmii_active = true; 189 break; 190 case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX: 191 case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES: 192 hw->phy.media_type = e1000_media_type_internal_serdes; 193 break; 194 default: 195 break; 196 } 197 198 /* Set mta register count */ 199 mac->mta_reg_count = 128; 200 /* Set rar entry count */ 201 switch (mac->type) { 202 case e1000_82576: 203 mac->rar_entry_count = E1000_RAR_ENTRIES_82576; 204 break; 205 case e1000_82580: 206 mac->rar_entry_count = E1000_RAR_ENTRIES_82580; 207 break; 208 case e1000_i350: 209 case e1000_i210: 210 case e1000_i211: 211 mac->rar_entry_count = E1000_RAR_ENTRIES_I350; 212 break; 213 default: 214 mac->rar_entry_count = E1000_RAR_ENTRIES_82575; 215 break; 216 } 217 /* reset */ 218 if (mac->type >= e1000_82580) 219 mac->ops.reset_hw = igb_reset_hw_82580; 220 else 221 mac->ops.reset_hw = igb_reset_hw_82575; 222 223 if (mac->type >= e1000_i210) { 224 mac->ops.acquire_swfw_sync = igb_acquire_swfw_sync_i210; 225 mac->ops.release_swfw_sync = igb_release_swfw_sync_i210; 226 } else { 227 mac->ops.acquire_swfw_sync = igb_acquire_swfw_sync_82575; 228 mac->ops.release_swfw_sync = igb_release_swfw_sync_82575; 229 } 230 231 /* Set if part includes ASF firmware */ 232 mac->asf_firmware_present = true; 233 /* Set if manageability features are enabled. */ 234 mac->arc_subsystem_valid = 235 (rd32(E1000_FWSM) & E1000_FWSM_MODE_MASK) 236 ? true : false; 237 /* enable EEE on i350 parts and later parts */ 238 if (mac->type >= e1000_i350) 239 dev_spec->eee_disable = false; 240 else 241 dev_spec->eee_disable = true; 242 /* physical interface link setup */ 243 mac->ops.setup_physical_interface = 244 (hw->phy.media_type == e1000_media_type_copper) 245 ? igb_setup_copper_link_82575 246 : igb_setup_serdes_link_82575; 247 248 /* NVM initialization */ 249 eecd = rd32(E1000_EECD); 250 size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >> 251 E1000_EECD_SIZE_EX_SHIFT); 252 253 /* 254 * Added to a constant, "size" becomes the left-shift value 255 * for setting word_size. 256 */ 257 size += NVM_WORD_SIZE_BASE_SHIFT; 258 259 nvm->word_size = 1 << size; 260 if (hw->mac.type < e1000_i210) { 261 nvm->opcode_bits = 8; 262 nvm->delay_usec = 1; 263 switch (nvm->override) { 264 case e1000_nvm_override_spi_large: 265 nvm->page_size = 32; 266 nvm->address_bits = 16; 267 break; 268 case e1000_nvm_override_spi_small: 269 nvm->page_size = 8; 270 nvm->address_bits = 8; 271 break; 272 default: 273 nvm->page_size = eecd 274 & E1000_EECD_ADDR_BITS ? 32 : 8; 275 nvm->address_bits = eecd 276 & E1000_EECD_ADDR_BITS ? 16 : 8; 277 break; 278 } 279 if (nvm->word_size == (1 << 15)) 280 nvm->page_size = 128; 281 282 nvm->type = e1000_nvm_eeprom_spi; 283 } else 284 nvm->type = e1000_nvm_flash_hw; 285 286 /* 287 * Check for invalid size 288 */ 289 if ((hw->mac.type == e1000_82576) && (size > 15)) { 290 pr_notice("The NVM size is not valid, defaulting to 32K\n"); 291 size = 15; 292 } 293 294 /* NVM Function Pointers */ 295 switch (hw->mac.type) { 296 case e1000_82580: 297 nvm->ops.validate = igb_validate_nvm_checksum_82580; 298 nvm->ops.update = igb_update_nvm_checksum_82580; 299 nvm->ops.acquire = igb_acquire_nvm_82575; 300 nvm->ops.release = igb_release_nvm_82575; 301 if (nvm->word_size < (1 << 15)) 302 nvm->ops.read = igb_read_nvm_eerd; 303 else 304 nvm->ops.read = igb_read_nvm_spi; 305 nvm->ops.write = igb_write_nvm_spi; 306 break; 307 case e1000_i350: 308 nvm->ops.validate = igb_validate_nvm_checksum_i350; 309 nvm->ops.update = igb_update_nvm_checksum_i350; 310 nvm->ops.acquire = igb_acquire_nvm_82575; 311 nvm->ops.release = igb_release_nvm_82575; 312 if (nvm->word_size < (1 << 15)) 313 nvm->ops.read = igb_read_nvm_eerd; 314 else 315 nvm->ops.read = igb_read_nvm_spi; 316 nvm->ops.write = igb_write_nvm_spi; 317 break; 318 case e1000_i210: 319 nvm->ops.validate = igb_validate_nvm_checksum_i210; 320 nvm->ops.update = igb_update_nvm_checksum_i210; 321 nvm->ops.acquire = igb_acquire_nvm_i210; 322 nvm->ops.release = igb_release_nvm_i210; 323 nvm->ops.read = igb_read_nvm_srrd_i210; 324 nvm->ops.valid_led_default = igb_valid_led_default_i210; 325 break; 326 case e1000_i211: 327 nvm->ops.acquire = igb_acquire_nvm_i210; 328 nvm->ops.release = igb_release_nvm_i210; 329 nvm->ops.read = igb_read_nvm_i211; 330 nvm->ops.valid_led_default = igb_valid_led_default_i210; 331 nvm->ops.validate = NULL; 332 nvm->ops.update = NULL; 333 nvm->ops.write = NULL; 334 break; 335 default: 336 nvm->ops.validate = igb_validate_nvm_checksum; 337 nvm->ops.update = igb_update_nvm_checksum; 338 nvm->ops.acquire = igb_acquire_nvm_82575; 339 nvm->ops.release = igb_release_nvm_82575; 340 if (nvm->word_size < (1 << 15)) 341 nvm->ops.read = igb_read_nvm_eerd; 342 else 343 nvm->ops.read = igb_read_nvm_spi; 344 nvm->ops.write = igb_write_nvm_spi; 345 break; 346 } 347 348 /* if part supports SR-IOV then initialize mailbox parameters */ 349 switch (mac->type) { 350 case e1000_82576: 351 case e1000_i350: 352 igb_init_mbx_params_pf(hw); 353 break; 354 default: 355 break; 356 } 357 358 /* setup PHY parameters */ 359 if (phy->media_type != e1000_media_type_copper) { 360 phy->type = e1000_phy_none; 361 return 0; 362 } 363 364 phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; 365 phy->reset_delay_us = 100; 366 367 ctrl_ext = rd32(E1000_CTRL_EXT); 368 369 /* PHY function pointers */ 370 if (igb_sgmii_active_82575(hw)) { 371 phy->ops.reset = igb_phy_hw_reset_sgmii_82575; 372 ctrl_ext |= E1000_CTRL_I2C_ENA; 373 } else { 374 phy->ops.reset = igb_phy_hw_reset; 375 ctrl_ext &= ~E1000_CTRL_I2C_ENA; 376 } 377 378 wr32(E1000_CTRL_EXT, ctrl_ext); 379 igb_reset_mdicnfg_82580(hw); 380 381 if (igb_sgmii_active_82575(hw) && !igb_sgmii_uses_mdio_82575(hw)) { 382 phy->ops.read_reg = igb_read_phy_reg_sgmii_82575; 383 phy->ops.write_reg = igb_write_phy_reg_sgmii_82575; 384 } else if ((hw->mac.type == e1000_82580) 385 || (hw->mac.type == e1000_i350)) { 386 phy->ops.read_reg = igb_read_phy_reg_82580; 387 phy->ops.write_reg = igb_write_phy_reg_82580; 388 } else if (hw->phy.type >= e1000_phy_i210) { 389 phy->ops.read_reg = igb_read_phy_reg_gs40g; 390 phy->ops.write_reg = igb_write_phy_reg_gs40g; 391 } else { 392 phy->ops.read_reg = igb_read_phy_reg_igp; 393 phy->ops.write_reg = igb_write_phy_reg_igp; 394 } 395 396 /* set lan id */ 397 hw->bus.func = (rd32(E1000_STATUS) & E1000_STATUS_FUNC_MASK) >> 398 E1000_STATUS_FUNC_SHIFT; 399 400 /* Set phy->phy_addr and phy->id. */ 401 ret_val = igb_get_phy_id_82575(hw); 402 if (ret_val) 403 return ret_val; 404 405 /* Verify phy id and set remaining function pointers */ 406 switch (phy->id) { 407 case I347AT4_E_PHY_ID: 408 case M88E1112_E_PHY_ID: 409 case M88E1111_I_PHY_ID: 410 phy->type = e1000_phy_m88; 411 phy->ops.get_phy_info = igb_get_phy_info_m88; 412 413 if (phy->id == I347AT4_E_PHY_ID || 414 phy->id == M88E1112_E_PHY_ID) 415 phy->ops.get_cable_length = igb_get_cable_length_m88_gen2; 416 else 417 phy->ops.get_cable_length = igb_get_cable_length_m88; 418 419 if (phy->id == I210_I_PHY_ID) { 420 phy->ops.get_cable_length = 421 igb_get_cable_length_m88_gen2; 422 phy->ops.set_d0_lplu_state = 423 igb_set_d0_lplu_state_82580; 424 phy->ops.set_d3_lplu_state = 425 igb_set_d3_lplu_state_82580; 426 } 427 phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_m88; 428 break; 429 case IGP03E1000_E_PHY_ID: 430 phy->type = e1000_phy_igp_3; 431 phy->ops.get_phy_info = igb_get_phy_info_igp; 432 phy->ops.get_cable_length = igb_get_cable_length_igp_2; 433 phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_igp; 434 phy->ops.set_d0_lplu_state = igb_set_d0_lplu_state_82575; 435 phy->ops.set_d3_lplu_state = igb_set_d3_lplu_state; 436 break; 437 case I82580_I_PHY_ID: 438 case I350_I_PHY_ID: 439 phy->type = e1000_phy_82580; 440 phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_82580; 441 phy->ops.get_cable_length = igb_get_cable_length_82580; 442 phy->ops.get_phy_info = igb_get_phy_info_82580; 443 phy->ops.set_d0_lplu_state = igb_set_d0_lplu_state_82580; 444 phy->ops.set_d3_lplu_state = igb_set_d3_lplu_state_82580; 445 break; 446 case I210_I_PHY_ID: 447 phy->type = e1000_phy_i210; 448 phy->ops.get_phy_info = igb_get_phy_info_m88; 449 phy->ops.check_polarity = igb_check_polarity_m88; 450 phy->ops.get_cable_length = igb_get_cable_length_m88_gen2; 451 phy->ops.set_d0_lplu_state = igb_set_d0_lplu_state_82580; 452 phy->ops.set_d3_lplu_state = igb_set_d3_lplu_state_82580; 453 phy->ops.force_speed_duplex = igb_phy_force_speed_duplex_m88; 454 break; 455 default: 456 return -E1000_ERR_PHY; 457 } 458 459 return 0; 460} 461 462/** 463 * igb_acquire_phy_82575 - Acquire rights to access PHY 464 * @hw: pointer to the HW structure 465 * 466 * Acquire access rights to the correct PHY. This is a 467 * function pointer entry point called by the api module. 468 **/ 469static s32 igb_acquire_phy_82575(struct e1000_hw *hw) 470{ 471 u16 mask = E1000_SWFW_PHY0_SM; 472 473 if (hw->bus.func == E1000_FUNC_1) 474 mask = E1000_SWFW_PHY1_SM; 475 else if (hw->bus.func == E1000_FUNC_2) 476 mask = E1000_SWFW_PHY2_SM; 477 else if (hw->bus.func == E1000_FUNC_3) 478 mask = E1000_SWFW_PHY3_SM; 479 480 return hw->mac.ops.acquire_swfw_sync(hw, mask); 481} 482 483/** 484 * igb_release_phy_82575 - Release rights to access PHY 485 * @hw: pointer to the HW structure 486 * 487 * A wrapper to release access rights to the correct PHY. This is a 488 * function pointer entry point called by the api module. 489 **/ 490static void igb_release_phy_82575(struct e1000_hw *hw) 491{ 492 u16 mask = E1000_SWFW_PHY0_SM; 493 494 if (hw->bus.func == E1000_FUNC_1) 495 mask = E1000_SWFW_PHY1_SM; 496 else if (hw->bus.func == E1000_FUNC_2) 497 mask = E1000_SWFW_PHY2_SM; 498 else if (hw->bus.func == E1000_FUNC_3) 499 mask = E1000_SWFW_PHY3_SM; 500 501 hw->mac.ops.release_swfw_sync(hw, mask); 502} 503 504/** 505 * igb_read_phy_reg_sgmii_82575 - Read PHY register using sgmii 506 * @hw: pointer to the HW structure 507 * @offset: register offset to be read 508 * @data: pointer to the read data 509 * 510 * Reads the PHY register at offset using the serial gigabit media independent 511 * interface and stores the retrieved information in data. 512 **/ 513static s32 igb_read_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset, 514 u16 *data) 515{ 516 s32 ret_val = -E1000_ERR_PARAM; 517 518 if (offset > E1000_MAX_SGMII_PHY_REG_ADDR) { 519 hw_dbg("PHY Address %u is out of range\n", offset); 520 goto out; 521 } 522 523 ret_val = hw->phy.ops.acquire(hw); 524 if (ret_val) 525 goto out; 526 527 ret_val = igb_read_phy_reg_i2c(hw, offset, data); 528 529 hw->phy.ops.release(hw); 530 531out: 532 return ret_val; 533} 534 535/** 536 * igb_write_phy_reg_sgmii_82575 - Write PHY register using sgmii 537 * @hw: pointer to the HW structure 538 * @offset: register offset to write to 539 * @data: data to write at register offset 540 * 541 * Writes the data to PHY register at the offset using the serial gigabit 542 * media independent interface. 543 **/ 544static s32 igb_write_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset, 545 u16 data) 546{ 547 s32 ret_val = -E1000_ERR_PARAM; 548 549 550 if (offset > E1000_MAX_SGMII_PHY_REG_ADDR) { 551 hw_dbg("PHY Address %d is out of range\n", offset); 552 goto out; 553 } 554 555 ret_val = hw->phy.ops.acquire(hw); 556 if (ret_val) 557 goto out; 558 559 ret_val = igb_write_phy_reg_i2c(hw, offset, data); 560 561 hw->phy.ops.release(hw); 562 563out: 564 return ret_val; 565} 566 567/** 568 * igb_get_phy_id_82575 - Retrieve PHY addr and id 569 * @hw: pointer to the HW structure 570 * 571 * Retrieves the PHY address and ID for both PHY's which do and do not use 572 * sgmi interface. 573 **/ 574static s32 igb_get_phy_id_82575(struct e1000_hw *hw) 575{ 576 struct e1000_phy_info *phy = &hw->phy; 577 s32 ret_val = 0; 578 u16 phy_id; 579 u32 ctrl_ext; 580 u32 mdic; 581 582 /* 583 * For SGMII PHYs, we try the list of possible addresses until 584 * we find one that works. For non-SGMII PHYs 585 * (e.g. integrated copper PHYs), an address of 1 should 586 * work. The result of this function should mean phy->phy_addr 587 * and phy->id are set correctly. 588 */ 589 if (!(igb_sgmii_active_82575(hw))) { 590 phy->addr = 1; 591 ret_val = igb_get_phy_id(hw); 592 goto out; 593 } 594 595 if (igb_sgmii_uses_mdio_82575(hw)) { 596 switch (hw->mac.type) { 597 case e1000_82575: 598 case e1000_82576: 599 mdic = rd32(E1000_MDIC); 600 mdic &= E1000_MDIC_PHY_MASK; 601 phy->addr = mdic >> E1000_MDIC_PHY_SHIFT; 602 break; 603 case e1000_82580: 604 case e1000_i350: 605 case e1000_i210: 606 case e1000_i211: 607 mdic = rd32(E1000_MDICNFG); 608 mdic &= E1000_MDICNFG_PHY_MASK; 609 phy->addr = mdic >> E1000_MDICNFG_PHY_SHIFT; 610 break; 611 default: 612 ret_val = -E1000_ERR_PHY; 613 goto out; 614 break; 615 } 616 ret_val = igb_get_phy_id(hw); 617 goto out; 618 } 619 620 /* Power on sgmii phy if it is disabled */ 621 ctrl_ext = rd32(E1000_CTRL_EXT); 622 wr32(E1000_CTRL_EXT, ctrl_ext & ~E1000_CTRL_EXT_SDP3_DATA); 623 wrfl(); 624 msleep(300); 625 626 /* 627 * The address field in the I2CCMD register is 3 bits and 0 is invalid. 628 * Therefore, we need to test 1-7 629 */ 630 for (phy->addr = 1; phy->addr < 8; phy->addr++) { 631 ret_val = igb_read_phy_reg_sgmii_82575(hw, PHY_ID1, &phy_id); 632 if (ret_val == 0) { 633 hw_dbg("Vendor ID 0x%08X read at address %u\n", 634 phy_id, phy->addr); 635 /* 636 * At the time of this writing, The M88 part is 637 * the only supported SGMII PHY product. 638 */ 639 if (phy_id == M88_VENDOR) 640 break; 641 } else { 642 hw_dbg("PHY address %u was unreadable\n", phy->addr); 643 } 644 } 645 646 /* A valid PHY type couldn't be found. */ 647 if (phy->addr == 8) { 648 phy->addr = 0; 649 ret_val = -E1000_ERR_PHY; 650 goto out; 651 } else { 652 ret_val = igb_get_phy_id(hw); 653 } 654 655 /* restore previous sfp cage power state */ 656 wr32(E1000_CTRL_EXT, ctrl_ext); 657 658out: 659 return ret_val; 660} 661 662/** 663 * igb_phy_hw_reset_sgmii_82575 - Performs a PHY reset 664 * @hw: pointer to the HW structure 665 * 666 * Resets the PHY using the serial gigabit media independent interface. 667 **/ 668static s32 igb_phy_hw_reset_sgmii_82575(struct e1000_hw *hw) 669{ 670 s32 ret_val; 671 672 /* 673 * This isn't a true "hard" reset, but is the only reset 674 * available to us at this time. 675 */ 676 677 hw_dbg("Soft resetting SGMII attached PHY...\n"); 678 679 /* 680 * SFP documentation requires the following to configure the SPF module 681 * to work on SGMII. No further documentation is given. 682 */ 683 ret_val = hw->phy.ops.write_reg(hw, 0x1B, 0x8084); 684 if (ret_val) 685 goto out; 686 687 ret_val = igb_phy_sw_reset(hw); 688 689out: 690 return ret_val; 691} 692 693/** 694 * igb_set_d0_lplu_state_82575 - Set Low Power Linkup D0 state 695 * @hw: pointer to the HW structure 696 * @active: true to enable LPLU, false to disable 697 * 698 * Sets the LPLU D0 state according to the active flag. When 699 * activating LPLU this function also disables smart speed 700 * and vice versa. LPLU will not be activated unless the 701 * device autonegotiation advertisement meets standards of 702 * either 10 or 10/100 or 10/100/1000 at all duplexes. 703 * This is a function pointer entry point only called by 704 * PHY setup routines. 705 **/ 706static s32 igb_set_d0_lplu_state_82575(struct e1000_hw *hw, bool active) 707{ 708 struct e1000_phy_info *phy = &hw->phy; 709 s32 ret_val; 710 u16 data; 711 712 ret_val = phy->ops.read_reg(hw, IGP02E1000_PHY_POWER_MGMT, &data); 713 if (ret_val) 714 goto out; 715 716 if (active) { 717 data |= IGP02E1000_PM_D0_LPLU; 718 ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT, 719 data); 720 if (ret_val) 721 goto out; 722 723 /* When LPLU is enabled, we should disable SmartSpeed */ 724 ret_val = phy->ops.read_reg(hw, IGP01E1000_PHY_PORT_CONFIG, 725 &data); 726 data &= ~IGP01E1000_PSCFR_SMART_SPEED; 727 ret_val = phy->ops.write_reg(hw, IGP01E1000_PHY_PORT_CONFIG, 728 data); 729 if (ret_val) 730 goto out; 731 } else { 732 data &= ~IGP02E1000_PM_D0_LPLU; 733 ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT, 734 data); 735 /* 736 * LPLU and SmartSpeed are mutually exclusive. LPLU is used 737 * during Dx states where the power conservation is most 738 * important. During driver activity we should enable 739 * SmartSpeed, so performance is maintained. 740 */ 741 if (phy->smart_speed == e1000_smart_speed_on) { 742 ret_val = phy->ops.read_reg(hw, 743 IGP01E1000_PHY_PORT_CONFIG, &data); 744 if (ret_val) 745 goto out; 746 747 data |= IGP01E1000_PSCFR_SMART_SPEED; 748 ret_val = phy->ops.write_reg(hw, 749 IGP01E1000_PHY_PORT_CONFIG, data); 750 if (ret_val) 751 goto out; 752 } else if (phy->smart_speed == e1000_smart_speed_off) { 753 ret_val = phy->ops.read_reg(hw, 754 IGP01E1000_PHY_PORT_CONFIG, &data); 755 if (ret_val) 756 goto out; 757 758 data &= ~IGP01E1000_PSCFR_SMART_SPEED; 759 ret_val = phy->ops.write_reg(hw, 760 IGP01E1000_PHY_PORT_CONFIG, data); 761 if (ret_val) 762 goto out; 763 } 764 } 765 766out: 767 return ret_val; 768} 769 770/** 771 * igb_set_d0_lplu_state_82580 - Set Low Power Linkup D0 state 772 * @hw: pointer to the HW structure 773 * @active: true to enable LPLU, false to disable 774 * 775 * Sets the LPLU D0 state according to the active flag. When 776 * activating LPLU this function also disables smart speed 777 * and vice versa. LPLU will not be activated unless the 778 * device autonegotiation advertisement meets standards of 779 * either 10 or 10/100 or 10/100/1000 at all duplexes. 780 * This is a function pointer entry point only called by 781 * PHY setup routines. 782 **/ 783static s32 igb_set_d0_lplu_state_82580(struct e1000_hw *hw, bool active) 784{ 785 struct e1000_phy_info *phy = &hw->phy; 786 s32 ret_val = 0; 787 u16 data; 788 789 data = rd32(E1000_82580_PHY_POWER_MGMT); 790 791 if (active) { 792 data |= E1000_82580_PM_D0_LPLU; 793 794 /* When LPLU is enabled, we should disable SmartSpeed */ 795 data &= ~E1000_82580_PM_SPD; 796 } else { 797 data &= ~E1000_82580_PM_D0_LPLU; 798 799 /* 800 * LPLU and SmartSpeed are mutually exclusive. LPLU is used 801 * during Dx states where the power conservation is most 802 * important. During driver activity we should enable 803 * SmartSpeed, so performance is maintained. 804 */ 805 if (phy->smart_speed == e1000_smart_speed_on) 806 data |= E1000_82580_PM_SPD; 807 else if (phy->smart_speed == e1000_smart_speed_off) 808 data &= ~E1000_82580_PM_SPD; } 809 810 wr32(E1000_82580_PHY_POWER_MGMT, data); 811 return ret_val; 812} 813 814/** 815 * igb_set_d3_lplu_state_82580 - Sets low power link up state for D3 816 * @hw: pointer to the HW structure 817 * @active: boolean used to enable/disable lplu 818 * 819 * Success returns 0, Failure returns 1 820 * 821 * The low power link up (lplu) state is set to the power management level D3 822 * and SmartSpeed is disabled when active is true, else clear lplu for D3 823 * and enable Smartspeed. LPLU and Smartspeed are mutually exclusive. LPLU 824 * is used during Dx states where the power conservation is most important. 825 * During driver activity, SmartSpeed should be enabled so performance is 826 * maintained. 827 **/ 828s32 igb_set_d3_lplu_state_82580(struct e1000_hw *hw, bool active) 829{ 830 struct e1000_phy_info *phy = &hw->phy; 831 s32 ret_val = 0; 832 u16 data; 833 834 data = rd32(E1000_82580_PHY_POWER_MGMT); 835 836 if (!active) { 837 data &= ~E1000_82580_PM_D3_LPLU; 838 /* 839 * LPLU and SmartSpeed are mutually exclusive. LPLU is used 840 * during Dx states where the power conservation is most 841 * important. During driver activity we should enable 842 * SmartSpeed, so performance is maintained. 843 */ 844 if (phy->smart_speed == e1000_smart_speed_on) 845 data |= E1000_82580_PM_SPD; 846 else if (phy->smart_speed == e1000_smart_speed_off) 847 data &= ~E1000_82580_PM_SPD; 848 } else if ((phy->autoneg_advertised == E1000_ALL_SPEED_DUPLEX) || 849 (phy->autoneg_advertised == E1000_ALL_NOT_GIG) || 850 (phy->autoneg_advertised == E1000_ALL_10_SPEED)) { 851 data |= E1000_82580_PM_D3_LPLU; 852 /* When LPLU is enabled, we should disable SmartSpeed */ 853 data &= ~E1000_82580_PM_SPD; 854 } 855 856 wr32(E1000_82580_PHY_POWER_MGMT, data); 857 return ret_val; 858} 859 860/** 861 * igb_acquire_nvm_82575 - Request for access to EEPROM 862 * @hw: pointer to the HW structure 863 * 864 * Acquire the necessary semaphores for exclusive access to the EEPROM. 865 * Set the EEPROM access request bit and wait for EEPROM access grant bit. 866 * Return successful if access grant bit set, else clear the request for 867 * EEPROM access and return -E1000_ERR_NVM (-1). 868 **/ 869static s32 igb_acquire_nvm_82575(struct e1000_hw *hw) 870{ 871 s32 ret_val; 872 873 ret_val = hw->mac.ops.acquire_swfw_sync(hw, E1000_SWFW_EEP_SM); 874 if (ret_val) 875 goto out; 876 877 ret_val = igb_acquire_nvm(hw); 878 879 if (ret_val) 880 hw->mac.ops.release_swfw_sync(hw, E1000_SWFW_EEP_SM); 881 882out: 883 return ret_val; 884} 885 886/** 887 * igb_release_nvm_82575 - Release exclusive access to EEPROM 888 * @hw: pointer to the HW structure 889 * 890 * Stop any current commands to the EEPROM and clear the EEPROM request bit, 891 * then release the semaphores acquired. 892 **/ 893static void igb_release_nvm_82575(struct e1000_hw *hw) 894{ 895 igb_release_nvm(hw); 896 hw->mac.ops.release_swfw_sync(hw, E1000_SWFW_EEP_SM); 897} 898 899/** 900 * igb_acquire_swfw_sync_82575 - Acquire SW/FW semaphore 901 * @hw: pointer to the HW structure 902 * @mask: specifies which semaphore to acquire 903 * 904 * Acquire the SW/FW semaphore to access the PHY or NVM. The mask 905 * will also specify which port we're acquiring the lock for. 906 **/ 907static s32 igb_acquire_swfw_sync_82575(struct e1000_hw *hw, u16 mask) 908{ 909 u32 swfw_sync; 910 u32 swmask = mask; 911 u32 fwmask = mask << 16; 912 s32 ret_val = 0; 913 s32 i = 0, timeout = 200; /* FIXME: find real value to use here */ 914 915 while (i < timeout) { 916 if (igb_get_hw_semaphore(hw)) { 917 ret_val = -E1000_ERR_SWFW_SYNC; 918 goto out; 919 } 920 921 swfw_sync = rd32(E1000_SW_FW_SYNC); 922 if (!(swfw_sync & (fwmask | swmask))) 923 break; 924 925 /* 926 * Firmware currently using resource (fwmask) 927 * or other software thread using resource (swmask) 928 */ 929 igb_put_hw_semaphore(hw); 930 mdelay(5); 931 i++; 932 } 933 934 if (i == timeout) { 935 hw_dbg("Driver can't access resource, SW_FW_SYNC timeout.\n"); 936 ret_val = -E1000_ERR_SWFW_SYNC; 937 goto out; 938 } 939 940 swfw_sync |= swmask; 941 wr32(E1000_SW_FW_SYNC, swfw_sync); 942 943 igb_put_hw_semaphore(hw); 944 945out: 946 return ret_val; 947} 948 949/** 950 * igb_release_swfw_sync_82575 - Release SW/FW semaphore 951 * @hw: pointer to the HW structure 952 * @mask: specifies which semaphore to acquire 953 * 954 * Release the SW/FW semaphore used to access the PHY or NVM. The mask 955 * will also specify which port we're releasing the lock for. 956 **/ 957static void igb_release_swfw_sync_82575(struct e1000_hw *hw, u16 mask) 958{ 959 u32 swfw_sync; 960 961 while (igb_get_hw_semaphore(hw) != 0); 962 /* Empty */ 963 964 swfw_sync = rd32(E1000_SW_FW_SYNC); 965 swfw_sync &= ~mask; 966 wr32(E1000_SW_FW_SYNC, swfw_sync); 967 968 igb_put_hw_semaphore(hw); 969} 970 971/** 972 * igb_get_cfg_done_82575 - Read config done bit 973 * @hw: pointer to the HW structure 974 * 975 * Read the management control register for the config done bit for 976 * completion status. NOTE: silicon which is EEPROM-less will fail trying 977 * to read the config done bit, so an error is *ONLY* logged and returns 978 * 0. If we were to return with error, EEPROM-less silicon 979 * would not be able to be reset or change link. 980 **/ 981static s32 igb_get_cfg_done_82575(struct e1000_hw *hw) 982{ 983 s32 timeout = PHY_CFG_TIMEOUT; 984 s32 ret_val = 0; 985 u32 mask = E1000_NVM_CFG_DONE_PORT_0; 986 987 if (hw->bus.func == 1) 988 mask = E1000_NVM_CFG_DONE_PORT_1; 989 else if (hw->bus.func == E1000_FUNC_2) 990 mask = E1000_NVM_CFG_DONE_PORT_2; 991 else if (hw->bus.func == E1000_FUNC_3) 992 mask = E1000_NVM_CFG_DONE_PORT_3; 993 994 while (timeout) { 995 if (rd32(E1000_EEMNGCTL) & mask) 996 break; 997 msleep(1); 998 timeout--; 999 } 1000 if (!timeout) 1001 hw_dbg("MNG configuration cycle has not completed.\n"); 1002 1003 /* If EEPROM is not marked present, init the PHY manually */ 1004 if (((rd32(E1000_EECD) & E1000_EECD_PRES) == 0) && 1005 (hw->phy.type == e1000_phy_igp_3)) 1006 igb_phy_init_script_igp3(hw); 1007 1008 return ret_val; 1009} 1010 1011/** 1012 * igb_check_for_link_82575 - Check for link 1013 * @hw: pointer to the HW structure 1014 * 1015 * If sgmii is enabled, then use the pcs register to determine link, otherwise 1016 * use the generic interface for determining link. 1017 **/ 1018static s32 igb_check_for_link_82575(struct e1000_hw *hw) 1019{ 1020 s32 ret_val; 1021 u16 speed, duplex; 1022 1023 if (hw->phy.media_type != e1000_media_type_copper) { 1024 ret_val = igb_get_pcs_speed_and_duplex_82575(hw, &speed, 1025 &duplex); 1026 /* 1027 * Use this flag to determine if link needs to be checked or 1028 * not. If we have link clear the flag so that we do not 1029 * continue to check for link. 1030 */ 1031 hw->mac.get_link_status = !hw->mac.serdes_has_link; 1032 } else { 1033 ret_val = igb_check_for_copper_link(hw); 1034 } 1035 1036 return ret_val; 1037} 1038 1039/** 1040 * igb_power_up_serdes_link_82575 - Power up the serdes link after shutdown 1041 * @hw: pointer to the HW structure 1042 **/ 1043void igb_power_up_serdes_link_82575(struct e1000_hw *hw) 1044{ 1045 u32 reg; 1046 1047 1048 if ((hw->phy.media_type != e1000_media_type_internal_serdes) && 1049 !igb_sgmii_active_82575(hw)) 1050 return; 1051 1052 /* Enable PCS to turn on link */ 1053 reg = rd32(E1000_PCS_CFG0); 1054 reg |= E1000_PCS_CFG_PCS_EN; 1055 wr32(E1000_PCS_CFG0, reg); 1056 1057 /* Power up the laser */ 1058 reg = rd32(E1000_CTRL_EXT); 1059 reg &= ~E1000_CTRL_EXT_SDP3_DATA; 1060 wr32(E1000_CTRL_EXT, reg); 1061 1062 /* flush the write to verify completion */ 1063 wrfl(); 1064 msleep(1); 1065} 1066 1067/** 1068 * igb_get_pcs_speed_and_duplex_82575 - Retrieve current speed/duplex 1069 * @hw: pointer to the HW structure 1070 * @speed: stores the current speed 1071 * @duplex: stores the current duplex 1072 * 1073 * Using the physical coding sub-layer (PCS), retrieve the current speed and 1074 * duplex, then store the values in the pointers provided. 1075 **/ 1076static s32 igb_get_pcs_speed_and_duplex_82575(struct e1000_hw *hw, u16 *speed, 1077 u16 *duplex) 1078{ 1079 struct e1000_mac_info *mac = &hw->mac; 1080 u32 pcs; 1081 1082 /* Set up defaults for the return values of this function */ 1083 mac->serdes_has_link = false; 1084 *speed = 0; 1085 *duplex = 0; 1086 1087 /* 1088 * Read the PCS Status register for link state. For non-copper mode, 1089 * the status register is not accurate. The PCS status register is 1090 * used instead. 1091 */ 1092 pcs = rd32(E1000_PCS_LSTAT); 1093 1094 /* 1095 * The link up bit determines when link is up on autoneg. The sync ok 1096 * gets set once both sides sync up and agree upon link. Stable link 1097 * can be determined by checking for both link up and link sync ok 1098 */ 1099 if ((pcs & E1000_PCS_LSTS_LINK_OK) && (pcs & E1000_PCS_LSTS_SYNK_OK)) { 1100 mac->serdes_has_link = true; 1101 1102 /* Detect and store PCS speed */ 1103 if (pcs & E1000_PCS_LSTS_SPEED_1000) { 1104 *speed = SPEED_1000; 1105 } else if (pcs & E1000_PCS_LSTS_SPEED_100) { 1106 *speed = SPEED_100; 1107 } else { 1108 *speed = SPEED_10; 1109 } 1110 1111 /* Detect and store PCS duplex */ 1112 if (pcs & E1000_PCS_LSTS_DUPLEX_FULL) { 1113 *duplex = FULL_DUPLEX; 1114 } else { 1115 *duplex = HALF_DUPLEX; 1116 } 1117 } 1118 1119 return 0; 1120} 1121 1122/** 1123 * igb_shutdown_serdes_link_82575 - Remove link during power down 1124 * @hw: pointer to the HW structure 1125 * 1126 * In the case of fiber serdes, shut down optics and PCS on driver unload 1127 * when management pass thru is not enabled. 1128 **/ 1129void igb_shutdown_serdes_link_82575(struct e1000_hw *hw) 1130{ 1131 u32 reg; 1132 1133 if (hw->phy.media_type != e1000_media_type_internal_serdes && 1134 igb_sgmii_active_82575(hw)) 1135 return; 1136 1137 if (!igb_enable_mng_pass_thru(hw)) { 1138 /* Disable PCS to turn off link */ 1139 reg = rd32(E1000_PCS_CFG0); 1140 reg &= ~E1000_PCS_CFG_PCS_EN; 1141 wr32(E1000_PCS_CFG0, reg); 1142 1143 /* shutdown the laser */ 1144 reg = rd32(E1000_CTRL_EXT); 1145 reg |= E1000_CTRL_EXT_SDP3_DATA; 1146 wr32(E1000_CTRL_EXT, reg); 1147 1148 /* flush the write to verify completion */ 1149 wrfl(); 1150 msleep(1); 1151 } 1152} 1153 1154/** 1155 * igb_reset_hw_82575 - Reset hardware 1156 * @hw: pointer to the HW structure 1157 * 1158 * This resets the hardware into a known state. This is a 1159 * function pointer entry point called by the api module. 1160 **/ 1161static s32 igb_reset_hw_82575(struct e1000_hw *hw) 1162{ 1163 u32 ctrl, icr; 1164 s32 ret_val; 1165 1166 /* 1167 * Prevent the PCI-E bus from sticking if there is no TLP connection 1168 * on the last TLP read/write transaction when MAC is reset. 1169 */ 1170 ret_val = igb_disable_pcie_master(hw); 1171 if (ret_val) 1172 hw_dbg("PCI-E Master disable polling has failed.\n"); 1173 1174 /* set the completion timeout for interface */ 1175 ret_val = igb_set_pcie_completion_timeout(hw); 1176 if (ret_val) { 1177 hw_dbg("PCI-E Set completion timeout has failed.\n"); 1178 } 1179 1180 hw_dbg("Masking off all interrupts\n"); 1181 wr32(E1000_IMC, 0xffffffff); 1182 1183 wr32(E1000_RCTL, 0); 1184 wr32(E1000_TCTL, E1000_TCTL_PSP); 1185 wrfl(); 1186 1187 msleep(10); 1188 1189 ctrl = rd32(E1000_CTRL); 1190 1191 hw_dbg("Issuing a global reset to MAC\n"); 1192 wr32(E1000_CTRL, ctrl | E1000_CTRL_RST); 1193 1194 ret_val = igb_get_auto_rd_done(hw); 1195 if (ret_val) { 1196 /* 1197 * When auto config read does not complete, do not 1198 * return with an error. This can happen in situations 1199 * where there is no eeprom and prevents getting link. 1200 */ 1201 hw_dbg("Auto Read Done did not complete\n"); 1202 } 1203 1204 /* If EEPROM is not present, run manual init scripts */ 1205 if ((rd32(E1000_EECD) & E1000_EECD_PRES) == 0) 1206 igb_reset_init_script_82575(hw); 1207 1208 /* Clear any pending interrupt events. */ 1209 wr32(E1000_IMC, 0xffffffff); 1210 icr = rd32(E1000_ICR); 1211 1212 /* Install any alternate MAC address into RAR0 */ 1213 ret_val = igb_check_alt_mac_addr(hw); 1214 1215 return ret_val; 1216} 1217 1218/** 1219 * igb_init_hw_82575 - Initialize hardware 1220 * @hw: pointer to the HW structure 1221 * 1222 * This inits the hardware readying it for operation. 1223 **/ 1224static s32 igb_init_hw_82575(struct e1000_hw *hw) 1225{ 1226 struct e1000_mac_info *mac = &hw->mac; 1227 s32 ret_val; 1228 u16 i, rar_count = mac->rar_entry_count; 1229 1230 /* Initialize identification LED */ 1231 ret_val = igb_id_led_init(hw); 1232 if (ret_val) { 1233 hw_dbg("Error initializing identification LED\n"); 1234 /* This is not fatal and we should not stop init due to this */ 1235 } 1236 1237 /* Disabling VLAN filtering */ 1238 hw_dbg("Initializing the IEEE VLAN\n"); 1239 if (hw->mac.type == e1000_i350) 1240 igb_clear_vfta_i350(hw); 1241 else 1242 igb_clear_vfta(hw); 1243 1244 /* Setup the receive address */ 1245 igb_init_rx_addrs(hw, rar_count); 1246 1247 /* Zero out the Multicast HASH table */ 1248 hw_dbg("Zeroing the MTA\n"); 1249 for (i = 0; i < mac->mta_reg_count; i++) 1250 array_wr32(E1000_MTA, i, 0); 1251 1252 /* Zero out the Unicast HASH table */ 1253 hw_dbg("Zeroing the UTA\n"); 1254 for (i = 0; i < mac->uta_reg_count; i++) 1255 array_wr32(E1000_UTA, i, 0); 1256 1257 /* Setup link and flow control */ 1258 ret_val = igb_setup_link(hw); 1259 1260 /* 1261 * Clear all of the statistics registers (clear on read). It is 1262 * important that we do this after we have tried to establish link 1263 * because the symbol error count will increment wildly if there 1264 * is no link. 1265 */ 1266 igb_clear_hw_cntrs_82575(hw); 1267 return ret_val; 1268} 1269 1270/** 1271 * igb_setup_copper_link_82575 - Configure copper link settings 1272 * @hw: pointer to the HW structure 1273 * 1274 * Configures the link for auto-neg or forced speed and duplex. Then we check 1275 * for link, once link is established calls to configure collision distance 1276 * and flow control are called. 1277 **/ 1278static s32 igb_setup_copper_link_82575(struct e1000_hw *hw) 1279{ 1280 u32 ctrl; 1281 s32 ret_val; 1282 1283 ctrl = rd32(E1000_CTRL); 1284 ctrl |= E1000_CTRL_SLU; 1285 ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); 1286 wr32(E1000_CTRL, ctrl); 1287 1288 ret_val = igb_setup_serdes_link_82575(hw); 1289 if (ret_val) 1290 goto out; 1291 1292 if (igb_sgmii_active_82575(hw) && !hw->phy.reset_disable) { 1293 /* allow time for SFP cage time to power up phy */ 1294 msleep(300); 1295 1296 ret_val = hw->phy.ops.reset(hw); 1297 if (ret_val) { 1298 hw_dbg("Error resetting the PHY.\n"); 1299 goto out; 1300 } 1301 } 1302 switch (hw->phy.type) { 1303 case e1000_phy_i210: 1304 case e1000_phy_m88: 1305 if (hw->phy.id == I347AT4_E_PHY_ID || 1306 hw->phy.id == M88E1112_E_PHY_ID) 1307 ret_val = igb_copper_link_setup_m88_gen2(hw); 1308 else 1309 ret_val = igb_copper_link_setup_m88(hw); 1310 break; 1311 case e1000_phy_igp_3: 1312 ret_val = igb_copper_link_setup_igp(hw); 1313 break; 1314 case e1000_phy_82580: 1315 ret_val = igb_copper_link_setup_82580(hw); 1316 break; 1317 default: 1318 ret_val = -E1000_ERR_PHY; 1319 break; 1320 } 1321 1322 if (ret_val) 1323 goto out; 1324 1325 ret_val = igb_setup_copper_link(hw); 1326out: 1327 return ret_val; 1328} 1329 1330/** 1331 * igb_setup_serdes_link_82575 - Setup link for serdes 1332 * @hw: pointer to the HW structure 1333 * 1334 * Configure the physical coding sub-layer (PCS) link. The PCS link is 1335 * used on copper connections where the serialized gigabit media independent 1336 * interface (sgmii), or serdes fiber is being used. Configures the link 1337 * for auto-negotiation or forces speed/duplex. 1338 **/ 1339static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw) 1340{ 1341 u32 ctrl_ext, ctrl_reg, reg; 1342 bool pcs_autoneg; 1343 s32 ret_val = E1000_SUCCESS; 1344 u16 data; 1345 1346 if ((hw->phy.media_type != e1000_media_type_internal_serdes) && 1347 !igb_sgmii_active_82575(hw)) 1348 return ret_val; 1349 1350 1351 /* 1352 * On the 82575, SerDes loopback mode persists until it is 1353 * explicitly turned off or a power cycle is performed. A read to 1354 * the register does not indicate its status. Therefore, we ensure 1355 * loopback mode is disabled during initialization. 1356 */ 1357 wr32(E1000_SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK); 1358 1359 /* power on the sfp cage if present */ 1360 ctrl_ext = rd32(E1000_CTRL_EXT); 1361 ctrl_ext &= ~E1000_CTRL_EXT_SDP3_DATA; 1362 wr32(E1000_CTRL_EXT, ctrl_ext); 1363 1364 ctrl_reg = rd32(E1000_CTRL); 1365 ctrl_reg |= E1000_CTRL_SLU; 1366 1367 if (hw->mac.type == e1000_82575 || hw->mac.type == e1000_82576) { 1368 /* set both sw defined pins */ 1369 ctrl_reg |= E1000_CTRL_SWDPIN0 | E1000_CTRL_SWDPIN1; 1370 1371 /* Set switch control to serdes energy detect */ 1372 reg = rd32(E1000_CONNSW); 1373 reg |= E1000_CONNSW_ENRGSRC; 1374 wr32(E1000_CONNSW, reg); 1375 } 1376 1377 reg = rd32(E1000_PCS_LCTL); 1378 1379 /* default pcs_autoneg to the same setting as mac autoneg */ 1380 pcs_autoneg = hw->mac.autoneg; 1381 1382 switch (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) { 1383 case E1000_CTRL_EXT_LINK_MODE_SGMII: 1384 /* sgmii mode lets the phy handle forcing speed/duplex */ 1385 pcs_autoneg = true; 1386 /* autoneg time out should be disabled for SGMII mode */ 1387 reg &= ~(E1000_PCS_LCTL_AN_TIMEOUT); 1388 break; 1389 case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX: 1390 /* disable PCS autoneg and support parallel detect only */ 1391 pcs_autoneg = false; 1392 default: 1393 if (hw->mac.type == e1000_82575 || 1394 hw->mac.type == e1000_82576) { 1395 ret_val = hw->nvm.ops.read(hw, NVM_COMPAT, 1, &data); 1396 if (ret_val) { 1397 printk(KERN_DEBUG "NVM Read Error\n\n"); 1398 return ret_val; 1399 } 1400 1401 if (data & E1000_EEPROM_PCS_AUTONEG_DISABLE_BIT) 1402 pcs_autoneg = false; 1403 } 1404 1405 /* 1406 * non-SGMII modes only supports a speed of 1000/Full for the 1407 * link so it is best to just force the MAC and let the pcs 1408 * link either autoneg or be forced to 1000/Full 1409 */ 1410 ctrl_reg |= E1000_CTRL_SPD_1000 | E1000_CTRL_FRCSPD | 1411 E1000_CTRL_FD | E1000_CTRL_FRCDPX; 1412 1413 /* set speed of 1000/Full if speed/duplex is forced */ 1414 reg |= E1000_PCS_LCTL_FSV_1000 | E1000_PCS_LCTL_FDV_FULL; 1415 break; 1416 } 1417 1418 wr32(E1000_CTRL, ctrl_reg); 1419 1420 /* 1421 * New SerDes mode allows for forcing speed or autonegotiating speed 1422 * at 1gb. Autoneg should be default set by most drivers. This is the 1423 * mode that will be compatible with older link partners and switches. 1424 * However, both are supported by the hardware and some drivers/tools. 1425 */ 1426 reg &= ~(E1000_PCS_LCTL_AN_ENABLE | E1000_PCS_LCTL_FLV_LINK_UP | 1427 E1000_PCS_LCTL_FSD | E1000_PCS_LCTL_FORCE_LINK); 1428 1429 /* 1430 * We force flow control to prevent the CTRL register values from being 1431 * overwritten by the autonegotiated flow control values 1432 */ 1433 reg |= E1000_PCS_LCTL_FORCE_FCTRL; 1434 1435 if (pcs_autoneg) { 1436 /* Set PCS register for autoneg */ 1437 reg |= E1000_PCS_LCTL_AN_ENABLE | /* Enable Autoneg */ 1438 E1000_PCS_LCTL_AN_RESTART; /* Restart autoneg */ 1439 hw_dbg("Configuring Autoneg:PCS_LCTL=0x%08X\n", reg); 1440 } else { 1441 /* Set PCS register for forced link */ 1442 reg |= E1000_PCS_LCTL_FSD; /* Force Speed */ 1443 1444 hw_dbg("Configuring Forced Link:PCS_LCTL=0x%08X\n", reg); 1445 } 1446 1447 wr32(E1000_PCS_LCTL, reg); 1448 1449 if (!igb_sgmii_active_82575(hw)) 1450 igb_force_mac_fc(hw); 1451 1452 return ret_val; 1453} 1454 1455/** 1456 * igb_sgmii_active_82575 - Return sgmii state 1457 * @hw: pointer to the HW structure 1458 * 1459 * 82575 silicon has a serialized gigabit media independent interface (sgmii) 1460 * which can be enabled for use in the embedded applications. Simply 1461 * return the current state of the sgmii interface. 1462 **/ 1463static bool igb_sgmii_active_82575(struct e1000_hw *hw) 1464{ 1465 struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575; 1466 return dev_spec->sgmii_active; 1467} 1468 1469/** 1470 * igb_reset_init_script_82575 - Inits HW defaults after reset 1471 * @hw: pointer to the HW structure 1472 * 1473 * Inits recommended HW defaults after a reset when there is no EEPROM 1474 * detected. This is only for the 82575. 1475 **/ 1476static s32 igb_reset_init_script_82575(struct e1000_hw *hw) 1477{ 1478 if (hw->mac.type == e1000_82575) { 1479 hw_dbg("Running reset init script for 82575\n"); 1480 /* SerDes configuration via SERDESCTRL */ 1481 igb_write_8bit_ctrl_reg(hw, E1000_SCTL, 0x00, 0x0C); 1482 igb_write_8bit_ctrl_reg(hw, E1000_SCTL, 0x01, 0x78); 1483 igb_write_8bit_ctrl_reg(hw, E1000_SCTL, 0x1B, 0x23); 1484 igb_write_8bit_ctrl_reg(hw, E1000_SCTL, 0x23, 0x15); 1485 1486 /* CCM configuration via CCMCTL register */ 1487 igb_write_8bit_ctrl_reg(hw, E1000_CCMCTL, 0x14, 0x00); 1488 igb_write_8bit_ctrl_reg(hw, E1000_CCMCTL, 0x10, 0x00); 1489 1490 /* PCIe lanes configuration */ 1491 igb_write_8bit_ctrl_reg(hw, E1000_GIOCTL, 0x00, 0xEC); 1492 igb_write_8bit_ctrl_reg(hw, E1000_GIOCTL, 0x61, 0xDF); 1493 igb_write_8bit_ctrl_reg(hw, E1000_GIOCTL, 0x34, 0x05); 1494 igb_write_8bit_ctrl_reg(hw, E1000_GIOCTL, 0x2F, 0x81); 1495 1496 /* PCIe PLL Configuration */ 1497 igb_write_8bit_ctrl_reg(hw, E1000_SCCTL, 0x02, 0x47); 1498 igb_write_8bit_ctrl_reg(hw, E1000_SCCTL, 0x14, 0x00); 1499 igb_write_8bit_ctrl_reg(hw, E1000_SCCTL, 0x10, 0x00); 1500 } 1501 1502 return 0; 1503} 1504 1505/** 1506 * igb_read_mac_addr_82575 - Read device MAC address 1507 * @hw: pointer to the HW structure 1508 **/ 1509static s32 igb_read_mac_addr_82575(struct e1000_hw *hw) 1510{ 1511 s32 ret_val = 0; 1512 1513 /* 1514 * If there's an alternate MAC address place it in RAR0 1515 * so that it will override the Si installed default perm 1516 * address. 1517 */ 1518 ret_val = igb_check_alt_mac_addr(hw); 1519 if (ret_val) 1520 goto out; 1521 1522 ret_val = igb_read_mac_addr(hw); 1523 1524out: 1525 return ret_val; 1526} 1527 1528/** 1529 * igb_power_down_phy_copper_82575 - Remove link during PHY power down 1530 * @hw: pointer to the HW structure 1531 * 1532 * In the case of a PHY power down to save power, or to turn off link during a 1533 * driver unload, or wake on lan is not enabled, remove the link. 1534 **/ 1535void igb_power_down_phy_copper_82575(struct e1000_hw *hw) 1536{ 1537 /* If the management interface is not enabled, then power down */ 1538 if (!(igb_enable_mng_pass_thru(hw) || igb_check_reset_block(hw))) 1539 igb_power_down_phy_copper(hw); 1540} 1541 1542/** 1543 * igb_clear_hw_cntrs_82575 - Clear device specific hardware counters 1544 * @hw: pointer to the HW structure 1545 * 1546 * Clears the hardware counters by reading the counter registers. 1547 **/ 1548static void igb_clear_hw_cntrs_82575(struct e1000_hw *hw) 1549{ 1550 igb_clear_hw_cntrs_base(hw); 1551 1552 rd32(E1000_PRC64); 1553 rd32(E1000_PRC127); 1554 rd32(E1000_PRC255); 1555 rd32(E1000_PRC511); 1556 rd32(E1000_PRC1023); 1557 rd32(E1000_PRC1522); 1558 rd32(E1000_PTC64); 1559 rd32(E1000_PTC127); 1560 rd32(E1000_PTC255); 1561 rd32(E1000_PTC511); 1562 rd32(E1000_PTC1023); 1563 rd32(E1000_PTC1522); 1564 1565 rd32(E1000_ALGNERRC); 1566 rd32(E1000_RXERRC); 1567 rd32(E1000_TNCRS); 1568 rd32(E1000_CEXTERR); 1569 rd32(E1000_TSCTC); 1570 rd32(E1000_TSCTFC); 1571 1572 rd32(E1000_MGTPRC); 1573 rd32(E1000_MGTPDC); 1574 rd32(E1000_MGTPTC); 1575 1576 rd32(E1000_IAC); 1577 rd32(E1000_ICRXOC); 1578 1579 rd32(E1000_ICRXPTC); 1580 rd32(E1000_ICRXATC); 1581 rd32(E1000_ICTXPTC); 1582 rd32(E1000_ICTXATC); 1583 rd32(E1000_ICTXQEC); 1584 rd32(E1000_ICTXQMTC); 1585 rd32(E1000_ICRXDMTC); 1586 1587 rd32(E1000_CBTMPC); 1588 rd32(E1000_HTDPMC); 1589 rd32(E1000_CBRMPC); 1590 rd32(E1000_RPTHC); 1591 rd32(E1000_HGPTC); 1592 rd32(E1000_HTCBDPC); 1593 rd32(E1000_HGORCL); 1594 rd32(E1000_HGORCH); 1595 rd32(E1000_HGOTCL); 1596 rd32(E1000_HGOTCH); 1597 rd32(E1000_LENERRS); 1598 1599 /* This register should not be read in copper configurations */ 1600 if (hw->phy.media_type == e1000_media_type_internal_serdes || 1601 igb_sgmii_active_82575(hw)) 1602 rd32(E1000_SCVPC); 1603} 1604 1605/** 1606 * igb_rx_fifo_flush_82575 - Clean rx fifo after RX enable 1607 * @hw: pointer to the HW structure 1608 * 1609 * After rx enable if managability is enabled then there is likely some 1610 * bad data at the start of the fifo and possibly in the DMA fifo. This 1611 * function clears the fifos and flushes any packets that came in as rx was 1612 * being enabled. 1613 **/ 1614void igb_rx_fifo_flush_82575(struct e1000_hw *hw) 1615{ 1616 u32 rctl, rlpml, rxdctl[4], rfctl, temp_rctl, rx_enabled; 1617 int i, ms_wait; 1618 1619 if (hw->mac.type != e1000_82575 || 1620 !(rd32(E1000_MANC) & E1000_MANC_RCV_TCO_EN)) 1621 return; 1622 1623 /* Disable all RX queues */ 1624 for (i = 0; i < 4; i++) { 1625 rxdctl[i] = rd32(E1000_RXDCTL(i)); 1626 wr32(E1000_RXDCTL(i), 1627 rxdctl[i] & ~E1000_RXDCTL_QUEUE_ENABLE); 1628 } 1629 /* Poll all queues to verify they have shut down */ 1630 for (ms_wait = 0; ms_wait < 10; ms_wait++) { 1631 msleep(1); 1632 rx_enabled = 0; 1633 for (i = 0; i < 4; i++) 1634 rx_enabled |= rd32(E1000_RXDCTL(i)); 1635 if (!(rx_enabled & E1000_RXDCTL_QUEUE_ENABLE)) 1636 break; 1637 } 1638 1639 if (ms_wait == 10) 1640 hw_dbg("Queue disable timed out after 10ms\n"); 1641 1642 /* Clear RLPML, RCTL.SBP, RFCTL.LEF, and set RCTL.LPE so that all 1643 * incoming packets are rejected. Set enable and wait 2ms so that 1644 * any packet that was coming in as RCTL.EN was set is flushed 1645 */ 1646 rfctl = rd32(E1000_RFCTL); 1647 wr32(E1000_RFCTL, rfctl & ~E1000_RFCTL_LEF); 1648 1649 rlpml = rd32(E1000_RLPML); 1650 wr32(E1000_RLPML, 0); 1651 1652 rctl = rd32(E1000_RCTL); 1653 temp_rctl = rctl & ~(E1000_RCTL_EN | E1000_RCTL_SBP); 1654 temp_rctl |= E1000_RCTL_LPE; 1655 1656 wr32(E1000_RCTL, temp_rctl); 1657 wr32(E1000_RCTL, temp_rctl | E1000_RCTL_EN); 1658 wrfl(); 1659 msleep(2); 1660 1661 /* Enable RX queues that were previously enabled and restore our 1662 * previous state 1663 */ 1664 for (i = 0; i < 4; i++) 1665 wr32(E1000_RXDCTL(i), rxdctl[i]); 1666 wr32(E1000_RCTL, rctl); 1667 wrfl(); 1668 1669 wr32(E1000_RLPML, rlpml); 1670 wr32(E1000_RFCTL, rfctl); 1671 1672 /* Flush receive errors generated by workaround */ 1673 rd32(E1000_ROC); 1674 rd32(E1000_RNBC); 1675 rd32(E1000_MPC); 1676} 1677 1678/** 1679 * igb_set_pcie_completion_timeout - set pci-e completion timeout 1680 * @hw: pointer to the HW structure 1681 * 1682 * The defaults for 82575 and 82576 should be in the range of 50us to 50ms, 1683 * however the hardware default for these parts is 500us to 1ms which is less 1684 * than the 10ms recommended by the pci-e spec. To address this we need to 1685 * increase the value to either 10ms to 200ms for capability version 1 config, 1686 * or 16ms to 55ms for version 2. 1687 **/ 1688static s32 igb_set_pcie_completion_timeout(struct e1000_hw *hw) 1689{ 1690 u32 gcr = rd32(E1000_GCR); 1691 s32 ret_val = 0; 1692 u16 pcie_devctl2; 1693 1694 /* only take action if timeout value is defaulted to 0 */ 1695 if (gcr & E1000_GCR_CMPL_TMOUT_MASK) 1696 goto out; 1697 1698 /* 1699 * if capababilities version is type 1 we can write the 1700 * timeout of 10ms to 200ms through the GCR register 1701 */ 1702 if (!(gcr & E1000_GCR_CAP_VER2)) { 1703 gcr |= E1000_GCR_CMPL_TMOUT_10ms; 1704 goto out; 1705 } 1706 1707 /* 1708 * for version 2 capabilities we need to write the config space 1709 * directly in order to set the completion timeout value for 1710 * 16ms to 55ms 1711 */ 1712 ret_val = igb_read_pcie_cap_reg(hw, PCIE_DEVICE_CONTROL2, 1713 &pcie_devctl2); 1714 if (ret_val) 1715 goto out; 1716 1717 pcie_devctl2 |= PCIE_DEVICE_CONTROL2_16ms; 1718 1719 ret_val = igb_write_pcie_cap_reg(hw, PCIE_DEVICE_CONTROL2, 1720 &pcie_devctl2); 1721out: 1722 /* disable completion timeout resend */ 1723 gcr &= ~E1000_GCR_CMPL_TMOUT_RESEND; 1724 1725 wr32(E1000_GCR, gcr); 1726 return ret_val; 1727} 1728 1729/** 1730 * igb_vmdq_set_anti_spoofing_pf - enable or disable anti-spoofing 1731 * @hw: pointer to the hardware struct 1732 * @enable: state to enter, either enabled or disabled 1733 * @pf: Physical Function pool - do not set anti-spoofing for the PF 1734 * 1735 * enables/disables L2 switch anti-spoofing functionality. 1736 **/ 1737void igb_vmdq_set_anti_spoofing_pf(struct e1000_hw *hw, bool enable, int pf) 1738{ 1739 u32 dtxswc; 1740 1741 switch (hw->mac.type) { 1742 case e1000_82576: 1743 case e1000_i350: 1744 dtxswc = rd32(E1000_DTXSWC); 1745 if (enable) { 1746 dtxswc |= (E1000_DTXSWC_MAC_SPOOF_MASK | 1747 E1000_DTXSWC_VLAN_SPOOF_MASK); 1748 /* The PF can spoof - it has to in order to 1749 * support emulation mode NICs */ 1750 dtxswc ^= (1 << pf | 1 << (pf + MAX_NUM_VFS)); 1751 } else { 1752 dtxswc &= ~(E1000_DTXSWC_MAC_SPOOF_MASK | 1753 E1000_DTXSWC_VLAN_SPOOF_MASK); 1754 } 1755 wr32(E1000_DTXSWC, dtxswc); 1756 break; 1757 default: 1758 break; 1759 } 1760} 1761 1762/** 1763 * igb_vmdq_set_loopback_pf - enable or disable vmdq loopback 1764 * @hw: pointer to the hardware struct 1765 * @enable: state to enter, either enabled or disabled 1766 * 1767 * enables/disables L2 switch loopback functionality. 1768 **/ 1769void igb_vmdq_set_loopback_pf(struct e1000_hw *hw, bool enable) 1770{ 1771 u32 dtxswc; 1772 1773 switch (hw->mac.type) { 1774 case e1000_82576: 1775 dtxswc = rd32(E1000_DTXSWC); 1776 if (enable) 1777 dtxswc |= E1000_DTXSWC_VMDQ_LOOPBACK_EN; 1778 else 1779 dtxswc &= ~E1000_DTXSWC_VMDQ_LOOPBACK_EN; 1780 wr32(E1000_DTXSWC, dtxswc); 1781 break; 1782 case e1000_i350: 1783 dtxswc = rd32(E1000_TXSWC); 1784 if (enable) 1785 dtxswc |= E1000_DTXSWC_VMDQ_LOOPBACK_EN; 1786 else 1787 dtxswc &= ~E1000_DTXSWC_VMDQ_LOOPBACK_EN; 1788 wr32(E1000_TXSWC, dtxswc); 1789 break; 1790 default: 1791 /* Currently no other hardware supports loopback */ 1792 break; 1793 } 1794 1795 1796} 1797 1798/** 1799 * igb_vmdq_set_replication_pf - enable or disable vmdq replication 1800 * @hw: pointer to the hardware struct 1801 * @enable: state to enter, either enabled or disabled 1802 * 1803 * enables/disables replication of packets across multiple pools. 1804 **/ 1805void igb_vmdq_set_replication_pf(struct e1000_hw *hw, bool enable) 1806{ 1807 u32 vt_ctl = rd32(E1000_VT_CTL); 1808 1809 if (enable) 1810 vt_ctl |= E1000_VT_CTL_VM_REPL_EN; 1811 else 1812 vt_ctl &= ~E1000_VT_CTL_VM_REPL_EN; 1813 1814 wr32(E1000_VT_CTL, vt_ctl); 1815} 1816 1817/** 1818 * igb_read_phy_reg_82580 - Read 82580 MDI control register 1819 * @hw: pointer to the HW structure 1820 * @offset: register offset to be read 1821 * @data: pointer to the read data 1822 * 1823 * Reads the MDI control register in the PHY at offset and stores the 1824 * information read to data. 1825 **/ 1826static s32 igb_read_phy_reg_82580(struct e1000_hw *hw, u32 offset, u16 *data) 1827{ 1828 s32 ret_val; 1829 1830 1831 ret_val = hw->phy.ops.acquire(hw); 1832 if (ret_val) 1833 goto out; 1834 1835 ret_val = igb_read_phy_reg_mdic(hw, offset, data); 1836 1837 hw->phy.ops.release(hw); 1838 1839out: 1840 return ret_val; 1841} 1842 1843/** 1844 * igb_write_phy_reg_82580 - Write 82580 MDI control register 1845 * @hw: pointer to the HW structure 1846 * @offset: register offset to write to 1847 * @data: data to write to register at offset 1848 * 1849 * Writes data to MDI control register in the PHY at offset. 1850 **/ 1851static s32 igb_write_phy_reg_82580(struct e1000_hw *hw, u32 offset, u16 data) 1852{ 1853 s32 ret_val; 1854 1855 1856 ret_val = hw->phy.ops.acquire(hw); 1857 if (ret_val) 1858 goto out; 1859 1860 ret_val = igb_write_phy_reg_mdic(hw, offset, data); 1861 1862 hw->phy.ops.release(hw); 1863 1864out: 1865 return ret_val; 1866} 1867 1868/** 1869 * igb_reset_mdicnfg_82580 - Reset MDICNFG destination and com_mdio bits 1870 * @hw: pointer to the HW structure 1871 * 1872 * This resets the the MDICNFG.Destination and MDICNFG.Com_MDIO bits based on 1873 * the values found in the EEPROM. This addresses an issue in which these 1874 * bits are not restored from EEPROM after reset. 1875 **/ 1876static s32 igb_reset_mdicnfg_82580(struct e1000_hw *hw) 1877{ 1878 s32 ret_val = 0; 1879 u32 mdicnfg; 1880 u16 nvm_data = 0; 1881 1882 if (hw->mac.type != e1000_82580) 1883 goto out; 1884 if (!igb_sgmii_active_82575(hw)) 1885 goto out; 1886 1887 ret_val = hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A + 1888 NVM_82580_LAN_FUNC_OFFSET(hw->bus.func), 1, 1889 &nvm_data); 1890 if (ret_val) { 1891 hw_dbg("NVM Read Error\n"); 1892 goto out; 1893 } 1894 1895 mdicnfg = rd32(E1000_MDICNFG); 1896 if (nvm_data & NVM_WORD24_EXT_MDIO) 1897 mdicnfg |= E1000_MDICNFG_EXT_MDIO; 1898 if (nvm_data & NVM_WORD24_COM_MDIO) 1899 mdicnfg |= E1000_MDICNFG_COM_MDIO; 1900 wr32(E1000_MDICNFG, mdicnfg); 1901out: 1902 return ret_val; 1903} 1904 1905/** 1906 * igb_reset_hw_82580 - Reset hardware 1907 * @hw: pointer to the HW structure 1908 * 1909 * This resets function or entire device (all ports, etc.) 1910 * to a known state. 1911 **/ 1912static s32 igb_reset_hw_82580(struct e1000_hw *hw) 1913{ 1914 s32 ret_val = 0; 1915 /* BH SW mailbox bit in SW_FW_SYNC */ 1916 u16 swmbsw_mask = E1000_SW_SYNCH_MB; 1917 u32 ctrl, icr; 1918 bool global_device_reset = hw->dev_spec._82575.global_device_reset; 1919 1920 1921 hw->dev_spec._82575.global_device_reset = false; 1922 1923 /* Get current control state. */ 1924 ctrl = rd32(E1000_CTRL); 1925 1926 /* 1927 * Prevent the PCI-E bus from sticking if there is no TLP connection 1928 * on the last TLP read/write transaction when MAC is reset. 1929 */ 1930 ret_val = igb_disable_pcie_master(hw); 1931 if (ret_val) 1932 hw_dbg("PCI-E Master disable polling has failed.\n"); 1933 1934 hw_dbg("Masking off all interrupts\n"); 1935 wr32(E1000_IMC, 0xffffffff); 1936 wr32(E1000_RCTL, 0); 1937 wr32(E1000_TCTL, E1000_TCTL_PSP); 1938 wrfl(); 1939 1940 msleep(10); 1941 1942 /* Determine whether or not a global dev reset is requested */ 1943 if (global_device_reset && 1944 hw->mac.ops.acquire_swfw_sync(hw, swmbsw_mask)) 1945 global_device_reset = false; 1946 1947 if (global_device_reset && 1948 !(rd32(E1000_STATUS) & E1000_STAT_DEV_RST_SET)) 1949 ctrl |= E1000_CTRL_DEV_RST; 1950 else 1951 ctrl |= E1000_CTRL_RST; 1952 1953 wr32(E1000_CTRL, ctrl); 1954 wrfl(); 1955 1956 /* Add delay to insure DEV_RST has time to complete */ 1957 if (global_device_reset) 1958 msleep(5); 1959 1960 ret_val = igb_get_auto_rd_done(hw); 1961 if (ret_val) { 1962 /* 1963 * When auto config read does not complete, do not 1964 * return with an error. This can happen in situations 1965 * where there is no eeprom and prevents getting link. 1966 */ 1967 hw_dbg("Auto Read Done did not complete\n"); 1968 } 1969 1970 /* If EEPROM is not present, run manual init scripts */ 1971 if ((rd32(E1000_EECD) & E1000_EECD_PRES) == 0) 1972 igb_reset_init_script_82575(hw); 1973 1974 /* clear global device reset status bit */ 1975 wr32(E1000_STATUS, E1000_STAT_DEV_RST_SET); 1976 1977 /* Clear any pending interrupt events. */ 1978 wr32(E1000_IMC, 0xffffffff); 1979 icr = rd32(E1000_ICR); 1980 1981 ret_val = igb_reset_mdicnfg_82580(hw); 1982 if (ret_val) 1983 hw_dbg("Could not reset MDICNFG based on EEPROM\n"); 1984 1985 /* Install any alternate MAC address into RAR0 */ 1986 ret_val = igb_check_alt_mac_addr(hw); 1987 1988 /* Release semaphore */ 1989 if (global_device_reset) 1990 hw->mac.ops.release_swfw_sync(hw, swmbsw_mask); 1991 1992 return ret_val; 1993} 1994 1995/** 1996 * igb_rxpbs_adjust_82580 - adjust RXPBS value to reflect actual RX PBA size 1997 * @data: data received by reading RXPBS register 1998 * 1999 * The 82580 uses a table based approach for packet buffer allocation sizes. 2000 * This function converts the retrieved value into the correct table value 2001 * 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 2002 * 0x0 36 72 144 1 2 4 8 16 2003 * 0x8 35 70 140 rsv rsv rsv rsv rsv 2004 */ 2005u16 igb_rxpbs_adjust_82580(u32 data) 2006{ 2007 u16 ret_val = 0; 2008 2009 if (data < E1000_82580_RXPBS_TABLE_SIZE) 2010 ret_val = e1000_82580_rxpbs_table[data]; 2011 2012 return ret_val; 2013} 2014 2015/** 2016 * igb_validate_nvm_checksum_with_offset - Validate EEPROM 2017 * checksum 2018 * @hw: pointer to the HW structure 2019 * @offset: offset in words of the checksum protected region 2020 * 2021 * Calculates the EEPROM checksum by reading/adding each word of the EEPROM 2022 * and then verifies that the sum of the EEPROM is equal to 0xBABA. 2023 **/ 2024static s32 igb_validate_nvm_checksum_with_offset(struct e1000_hw *hw, 2025 u16 offset) 2026{ 2027 s32 ret_val = 0; 2028 u16 checksum = 0; 2029 u16 i, nvm_data; 2030 2031 for (i = offset; i < ((NVM_CHECKSUM_REG + offset) + 1); i++) { 2032 ret_val = hw->nvm.ops.read(hw, i, 1, &nvm_data); 2033 if (ret_val) { 2034 hw_dbg("NVM Read Error\n"); 2035 goto out; 2036 } 2037 checksum += nvm_data; 2038 } 2039 2040 if (checksum != (u16) NVM_SUM) { 2041 hw_dbg("NVM Checksum Invalid\n"); 2042 ret_val = -E1000_ERR_NVM; 2043 goto out; 2044 } 2045 2046out: 2047 return ret_val; 2048} 2049 2050/** 2051 * igb_update_nvm_checksum_with_offset - Update EEPROM 2052 * checksum 2053 * @hw: pointer to the HW structure 2054 * @offset: offset in words of the checksum protected region 2055 * 2056 * Updates the EEPROM checksum by reading/adding each word of the EEPROM 2057 * up to the checksum. Then calculates the EEPROM checksum and writes the 2058 * value to the EEPROM. 2059 **/ 2060static s32 igb_update_nvm_checksum_with_offset(struct e1000_hw *hw, u16 offset) 2061{ 2062 s32 ret_val; 2063 u16 checksum = 0; 2064 u16 i, nvm_data; 2065 2066 for (i = offset; i < (NVM_CHECKSUM_REG + offset); i++) { 2067 ret_val = hw->nvm.ops.read(hw, i, 1, &nvm_data); 2068 if (ret_val) { 2069 hw_dbg("NVM Read Error while updating checksum.\n"); 2070 goto out; 2071 } 2072 checksum += nvm_data; 2073 } 2074 checksum = (u16) NVM_SUM - checksum; 2075 ret_val = hw->nvm.ops.write(hw, (NVM_CHECKSUM_REG + offset), 1, 2076 &checksum); 2077 if (ret_val) 2078 hw_dbg("NVM Write Error while updating checksum.\n"); 2079 2080out: 2081 return ret_val; 2082} 2083 2084/** 2085 * igb_validate_nvm_checksum_82580 - Validate EEPROM checksum 2086 * @hw: pointer to the HW structure 2087 * 2088 * Calculates the EEPROM section checksum by reading/adding each word of 2089 * the EEPROM and then verifies that the sum of the EEPROM is 2090 * equal to 0xBABA. 2091 **/ 2092static s32 igb_validate_nvm_checksum_82580(struct e1000_hw *hw) 2093{ 2094 s32 ret_val = 0; 2095 u16 eeprom_regions_count = 1; 2096 u16 j, nvm_data; 2097 u16 nvm_offset; 2098 2099 ret_val = hw->nvm.ops.read(hw, NVM_COMPATIBILITY_REG_3, 1, &nvm_data); 2100 if (ret_val) { 2101 hw_dbg("NVM Read Error\n"); 2102 goto out; 2103 } 2104 2105 if (nvm_data & NVM_COMPATIBILITY_BIT_MASK) { 2106 /* if checksums compatibility bit is set validate checksums 2107 * for all 4 ports. */ 2108 eeprom_regions_count = 4; 2109 } 2110 2111 for (j = 0; j < eeprom_regions_count; j++) { 2112 nvm_offset = NVM_82580_LAN_FUNC_OFFSET(j); 2113 ret_val = igb_validate_nvm_checksum_with_offset(hw, 2114 nvm_offset); 2115 if (ret_val != 0) 2116 goto out; 2117 } 2118 2119out: 2120 return ret_val; 2121} 2122 2123/** 2124 * igb_update_nvm_checksum_82580 - Update EEPROM checksum 2125 * @hw: pointer to the HW structure 2126 * 2127 * Updates the EEPROM section checksums for all 4 ports by reading/adding 2128 * each word of the EEPROM up to the checksum. Then calculates the EEPROM 2129 * checksum and writes the value to the EEPROM. 2130 **/ 2131static s32 igb_update_nvm_checksum_82580(struct e1000_hw *hw) 2132{ 2133 s32 ret_val; 2134 u16 j, nvm_data; 2135 u16 nvm_offset; 2136 2137 ret_val = hw->nvm.ops.read(hw, NVM_COMPATIBILITY_REG_3, 1, &nvm_data); 2138 if (ret_val) { 2139 hw_dbg("NVM Read Error while updating checksum" 2140 " compatibility bit.\n"); 2141 goto out; 2142 } 2143 2144 if ((nvm_data & NVM_COMPATIBILITY_BIT_MASK) == 0) { 2145 /* set compatibility bit to validate checksums appropriately */ 2146 nvm_data = nvm_data | NVM_COMPATIBILITY_BIT_MASK; 2147 ret_val = hw->nvm.ops.write(hw, NVM_COMPATIBILITY_REG_3, 1, 2148 &nvm_data); 2149 if (ret_val) { 2150 hw_dbg("NVM Write Error while updating checksum" 2151 " compatibility bit.\n"); 2152 goto out; 2153 } 2154 } 2155 2156 for (j = 0; j < 4; j++) { 2157 nvm_offset = NVM_82580_LAN_FUNC_OFFSET(j); 2158 ret_val = igb_update_nvm_checksum_with_offset(hw, nvm_offset); 2159 if (ret_val) 2160 goto out; 2161 } 2162 2163out: 2164 return ret_val; 2165} 2166 2167/** 2168 * igb_validate_nvm_checksum_i350 - Validate EEPROM checksum 2169 * @hw: pointer to the HW structure 2170 * 2171 * Calculates the EEPROM section checksum by reading/adding each word of 2172 * the EEPROM and then verifies that the sum of the EEPROM is 2173 * equal to 0xBABA. 2174 **/ 2175static s32 igb_validate_nvm_checksum_i350(struct e1000_hw *hw) 2176{ 2177 s32 ret_val = 0; 2178 u16 j; 2179 u16 nvm_offset; 2180 2181 for (j = 0; j < 4; j++) { 2182 nvm_offset = NVM_82580_LAN_FUNC_OFFSET(j); 2183 ret_val = igb_validate_nvm_checksum_with_offset(hw, 2184 nvm_offset); 2185 if (ret_val != 0) 2186 goto out; 2187 } 2188 2189out: 2190 return ret_val; 2191} 2192 2193/** 2194 * igb_update_nvm_checksum_i350 - Update EEPROM checksum 2195 * @hw: pointer to the HW structure 2196 * 2197 * Updates the EEPROM section checksums for all 4 ports by reading/adding 2198 * each word of the EEPROM up to the checksum. Then calculates the EEPROM 2199 * checksum and writes the value to the EEPROM. 2200 **/ 2201static s32 igb_update_nvm_checksum_i350(struct e1000_hw *hw) 2202{ 2203 s32 ret_val = 0; 2204 u16 j; 2205 u16 nvm_offset; 2206 2207 for (j = 0; j < 4; j++) { 2208 nvm_offset = NVM_82580_LAN_FUNC_OFFSET(j); 2209 ret_val = igb_update_nvm_checksum_with_offset(hw, nvm_offset); 2210 if (ret_val != 0) 2211 goto out; 2212 } 2213 2214out: 2215 return ret_val; 2216} 2217 2218/** 2219 * igb_set_eee_i350 - Enable/disable EEE support 2220 * @hw: pointer to the HW structure 2221 * 2222 * Enable/disable EEE based on setting in dev_spec structure. 2223 * 2224 **/ 2225s32 igb_set_eee_i350(struct e1000_hw *hw) 2226{ 2227 s32 ret_val = 0; 2228 u32 ipcnfg, eeer, ctrl_ext; 2229 2230 ctrl_ext = rd32(E1000_CTRL_EXT); 2231 if ((hw->mac.type != e1000_i350) || 2232 (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK)) 2233 goto out; 2234 ipcnfg = rd32(E1000_IPCNFG); 2235 eeer = rd32(E1000_EEER); 2236 2237 /* enable or disable per user setting */ 2238 if (!(hw->dev_spec._82575.eee_disable)) { 2239 ipcnfg |= (E1000_IPCNFG_EEE_1G_AN | 2240 E1000_IPCNFG_EEE_100M_AN); 2241 eeer |= (E1000_EEER_TX_LPI_EN | 2242 E1000_EEER_RX_LPI_EN | 2243 E1000_EEER_LPI_FC); 2244 2245 } else { 2246 ipcnfg &= ~(E1000_IPCNFG_EEE_1G_AN | 2247 E1000_IPCNFG_EEE_100M_AN); 2248 eeer &= ~(E1000_EEER_TX_LPI_EN | 2249 E1000_EEER_RX_LPI_EN | 2250 E1000_EEER_LPI_FC); 2251 } 2252 wr32(E1000_IPCNFG, ipcnfg); 2253 wr32(E1000_EEER, eeer); 2254out: 2255 2256 return ret_val; 2257} 2258 2259static struct e1000_mac_operations e1000_mac_ops_82575 = { 2260 .init_hw = igb_init_hw_82575, 2261 .check_for_link = igb_check_for_link_82575, 2262 .rar_set = igb_rar_set, 2263 .read_mac_addr = igb_read_mac_addr_82575, 2264 .get_speed_and_duplex = igb_get_speed_and_duplex_copper, 2265}; 2266 2267static struct e1000_phy_operations e1000_phy_ops_82575 = { 2268 .acquire = igb_acquire_phy_82575, 2269 .get_cfg_done = igb_get_cfg_done_82575, 2270 .release = igb_release_phy_82575, 2271}; 2272 2273static struct e1000_nvm_operations e1000_nvm_ops_82575 = { 2274 .acquire = igb_acquire_nvm_82575, 2275 .read = igb_read_nvm_eerd, 2276 .release = igb_release_nvm_82575, 2277 .write = igb_write_nvm_spi, 2278}; 2279 2280const struct e1000_info e1000_82575_info = { 2281 .get_invariants = igb_get_invariants_82575, 2282 .mac_ops = &e1000_mac_ops_82575, 2283 .phy_ops = &e1000_phy_ops_82575, 2284 .nvm_ops = &e1000_nvm_ops_82575, 2285}; 2286 2287