ni_atmio.c revision 615c902fb824d8273dd2b6837cda7ecb36b487e7 
1/*
2    comedi/drivers/ni_atmio.c
3    Hardware driver for NI AT-MIO E series cards
4
5    COMEDI - Linux Control and Measurement Device Interface
6    Copyright (C) 1997-2001 David A. Schleef <ds@schleef.org>
7
8    This program is free software; you can redistribute it and/or modify
9    it under the terms of the GNU General Public License as published by
10    the Free Software Foundation; either version 2 of the License, or
11    (at your option) any later version.
12
13    This program is distributed in the hope that it will be useful,
14    but WITHOUT ANY WARRANTY; without even the implied warranty of
15    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
16    GNU General Public License for more details.
17
18    You should have received a copy of the GNU General Public License
19    along with this program; if not, write to the Free Software
20    Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
21*/
22/*
23Driver: ni_atmio
24Description: National Instruments AT-MIO-E series
25Author: ds
26Devices: [National Instruments] AT-MIO-16E-1 (ni_atmio),
27  AT-MIO-16E-2, AT-MIO-16E-10, AT-MIO-16DE-10, AT-MIO-64E-3,
28  AT-MIO-16XE-50, AT-MIO-16XE-10, AT-AI-16XE-10
29Status: works
30Updated: Thu May  1 20:03:02 CDT 2003
31
32The driver has 2.6 kernel isapnp support, and
33will automatically probe for a supported board if the
34I/O base is left unspecified with comedi_config.
35However, many of
36the isapnp id numbers are unknown.  If your board is not
37recognized, please send the output of 'cat /proc/isapnp'
38(you may need to modprobe the isa-pnp module for
39/proc/isapnp to exist) so the
40id numbers for your board can be added to the driver.
41
42Otherwise, you can use the isapnptools package to configure
43your board.  Use isapnp to
44configure the I/O base and IRQ for the board, and then pass
45the same values as
46parameters in comedi_config.  A sample isapnp.conf file is included
47in the etc/ directory of Comedilib.
48
49Comedilib includes a utility to autocalibrate these boards.  The
50boards seem to boot into a state where the all calibration DACs
51are at one extreme of their range, thus the default calibration
52is terrible.  Calibration at boot is strongly encouraged.
53
54To use the extended digital I/O on some of the boards, enable the
558255 driver when configuring the Comedi source tree.
56
57External triggering is supported for some events.  The channel index
58(scan_begin_arg, etc.) maps to PFI0 - PFI9.
59
60Some of the more esoteric triggering possibilities of these boards
61are not supported.
62*/
63/*
64	The real guts of the driver is in ni_mio_common.c, which is included
65	both here and in ni_pcimio.c
66
67	Interrupt support added by Truxton Fulton <trux@truxton.com>
68
69	References for specifications:
70
71	   340747b.pdf  Register Level Programmer Manual (obsolete)
72	   340747c.pdf  Register Level Programmer Manual (new)
73	   DAQ-STC reference manual
74
75	Other possibly relevant info:
76
77	   320517c.pdf  User manual (obsolete)
78	   320517f.pdf  User manual (new)
79	   320889a.pdf  delete
80	   320906c.pdf  maximum signal ratings
81	   321066a.pdf  about 16x
82	   321791a.pdf  discontinuation of at-mio-16e-10 rev. c
83	   321808a.pdf  about at-mio-16e-10 rev P
84	   321837a.pdf  discontinuation of at-mio-16de-10 rev d
85	   321838a.pdf  about at-mio-16de-10 rev N
86
87	ISSUES:
88
89	need to deal with external reference for DAC, and other DAC
90	properties in board properties
91
92	deal with at-mio-16de-10 revision D to N changes, etc.
93
94*/
95
96#include <linux/interrupt.h>
97#include "../comedidev.h"
98
99#include <linux/delay.h>
100#include <linux/isapnp.h>
101
102#include "ni_stc.h"
103#include "8255.h"
104
105#undef DEBUG
106
107#define ATMIO 1
108#undef PCIMIO
109
110/*
111 *  AT specific setup
112 */
113
114#define NI_SIZE 0x20
115
116#define MAX_N_CALDACS 32
117
118static const struct ni_board_struct ni_boards[] = {
119	{.device_id = 44,
120	 .isapnp_id = 0x0000,	/* XXX unknown */
121	 .name = "at-mio-16e-1",
122	 .n_adchan = 16,
123	 .adbits = 12,
124	 .ai_fifo_depth = 8192,
125	 .alwaysdither = 0,
126	 .gainlkup = ai_gain_16,
127	 .ai_speed = 800,
128	 .n_aochan = 2,
129	 .aobits = 12,
130	 .ao_fifo_depth = 2048,
131	 .ao_range_table = &range_ni_E_ao_ext,
132	 .ao_unipolar = 1,
133	 .ao_speed = 1000,
134	 .has_8255 = 0,
135	 .num_p0_dio_channels = 8,
136	 .caldac = {mb88341},
137	 },
138	{.device_id = 25,
139	 .isapnp_id = 0x1900,
140	 .name = "at-mio-16e-2",
141	 .n_adchan = 16,
142	 .adbits = 12,
143	 .ai_fifo_depth = 2048,
144	 .alwaysdither = 0,
145	 .gainlkup = ai_gain_16,
146	 .ai_speed = 2000,
147	 .n_aochan = 2,
148	 .aobits = 12,
149	 .ao_fifo_depth = 2048,
150	 .ao_range_table = &range_ni_E_ao_ext,
151	 .ao_unipolar = 1,
152	 .ao_speed = 1000,
153	 .has_8255 = 0,
154	 .num_p0_dio_channels = 8,
155	 .caldac = {mb88341},
156	 },
157	{.device_id = 36,
158	 .isapnp_id = 0x2400,
159	 .name = "at-mio-16e-10",
160	 .n_adchan = 16,
161	 .adbits = 12,
162	 .ai_fifo_depth = 512,
163	 .alwaysdither = 0,
164	 .gainlkup = ai_gain_16,
165	 .ai_speed = 10000,
166	 .n_aochan = 2,
167	 .aobits = 12,
168	 .ao_fifo_depth = 0,
169	 .ao_range_table = &range_ni_E_ao_ext,
170	 .ao_unipolar = 1,
171	 .ao_speed = 10000,
172	 .num_p0_dio_channels = 8,
173	 .caldac = {ad8804_debug},
174	 .has_8255 = 0,
175	 },
176	{.device_id = 37,
177	 .isapnp_id = 0x2500,
178	 .name = "at-mio-16de-10",
179	 .n_adchan = 16,
180	 .adbits = 12,
181	 .ai_fifo_depth = 512,
182	 .alwaysdither = 0,
183	 .gainlkup = ai_gain_16,
184	 .ai_speed = 10000,
185	 .n_aochan = 2,
186	 .aobits = 12,
187	 .ao_fifo_depth = 0,
188	 .ao_range_table = &range_ni_E_ao_ext,
189	 .ao_unipolar = 1,
190	 .ao_speed = 10000,
191	 .num_p0_dio_channels = 8,
192	 .caldac = {ad8804_debug},
193	 .has_8255 = 1,
194	 },
195	{.device_id = 38,
196	 .isapnp_id = 0x2600,
197	 .name = "at-mio-64e-3",
198	 .n_adchan = 64,
199	 .adbits = 12,
200	 .ai_fifo_depth = 2048,
201	 .alwaysdither = 0,
202	 .gainlkup = ai_gain_16,
203	 .ai_speed = 2000,
204	 .n_aochan = 2,
205	 .aobits = 12,
206	 .ao_fifo_depth = 2048,
207	 .ao_range_table = &range_ni_E_ao_ext,
208	 .ao_unipolar = 1,
209	 .ao_speed = 1000,
210	 .has_8255 = 0,
211	 .num_p0_dio_channels = 8,
212	 .caldac = {ad8804_debug},
213	 },
214	{.device_id = 39,
215	 .isapnp_id = 0x2700,
216	 .name = "at-mio-16xe-50",
217	 .n_adchan = 16,
218	 .adbits = 16,
219	 .ai_fifo_depth = 512,
220	 .alwaysdither = 1,
221	 .gainlkup = ai_gain_8,
222	 .ai_speed = 50000,
223	 .n_aochan = 2,
224	 .aobits = 12,
225	 .ao_fifo_depth = 0,
226	 .ao_range_table = &range_bipolar10,
227	 .ao_unipolar = 0,
228	 .ao_speed = 50000,
229	 .num_p0_dio_channels = 8,
230	 .caldac = {dac8800, dac8043},
231	 .has_8255 = 0,
232	 },
233	{.device_id = 50,
234	 .isapnp_id = 0x0000,	/* XXX unknown */
235	 .name = "at-mio-16xe-10",
236	 .n_adchan = 16,
237	 .adbits = 16,
238	 .ai_fifo_depth = 512,
239	 .alwaysdither = 1,
240	 .gainlkup = ai_gain_14,
241	 .ai_speed = 10000,
242	 .n_aochan = 2,
243	 .aobits = 16,
244	 .ao_fifo_depth = 2048,
245	 .ao_range_table = &range_ni_E_ao_ext,
246	 .ao_unipolar = 1,
247	 .ao_speed = 1000,
248	 .num_p0_dio_channels = 8,
249	 .caldac = {dac8800, dac8043, ad8522},
250	 .has_8255 = 0,
251	 },
252	{.device_id = 51,
253	 .isapnp_id = 0x0000,	/* XXX unknown */
254	 .name = "at-ai-16xe-10",
255	 .n_adchan = 16,
256	 .adbits = 16,
257	 .ai_fifo_depth = 512,
258	 .alwaysdither = 1,	/* unknown */
259	 .gainlkup = ai_gain_14,
260	 .ai_speed = 10000,
261	 .n_aochan = 0,
262	 .aobits = 0,
263	 .ao_fifo_depth = 0,
264	 .ao_unipolar = 0,
265	 .num_p0_dio_channels = 8,
266	 .caldac = {dac8800, dac8043, ad8522},
267	 .has_8255 = 0,
268	 }
269};
270
271static const int ni_irqpin[] = {
272	-1, -1, -1, 0, 1, 2, -1, 3, -1, -1, 4, 5, 6, -1, -1, 7
273};
274
275#define interrupt_pin(a)	(ni_irqpin[(a)])
276
277#define IRQ_POLARITY 0
278
279#define NI_E_IRQ_FLAGS		0
280
281struct ni_private {
282	struct pnp_dev *isapnp_dev;
283	NI_PRIVATE_COMMON
284
285};
286
287/* How we access registers */
288
289#define ni_writel(a, b)		(outl((a), (b)+dev->iobase))
290#define ni_readl(a)		(inl((a)+dev->iobase))
291#define ni_writew(a, b)		(outw((a), (b)+dev->iobase))
292#define ni_readw(a)		(inw((a)+dev->iobase))
293#define ni_writeb(a, b)		(outb((a), (b)+dev->iobase))
294#define ni_readb(a)		(inb((a)+dev->iobase))
295
296/* How we access windowed registers */
297
298/* We automatically take advantage of STC registers that can be
299 * read/written directly in the I/O space of the board.  The
300 * AT-MIO devices map the low 8 STC registers to iobase+addr*2. */
301
302static void ni_atmio_win_out(struct comedi_device *dev, uint16_t data, int addr)
303{
304	struct ni_private *devpriv = dev->private;
305	unsigned long flags;
306
307	spin_lock_irqsave(&devpriv->window_lock, flags);
308	if ((addr) < 8) {
309		ni_writew(data, addr * 2);
310	} else {
311		ni_writew(addr, Window_Address);
312		ni_writew(data, Window_Data);
313	}
314	spin_unlock_irqrestore(&devpriv->window_lock, flags);
315}
316
317static uint16_t ni_atmio_win_in(struct comedi_device *dev, int addr)
318{
319	struct ni_private *devpriv = dev->private;
320	unsigned long flags;
321	uint16_t ret;
322
323	spin_lock_irqsave(&devpriv->window_lock, flags);
324	if (addr < 8) {
325		ret = ni_readw(addr * 2);
326	} else {
327		ni_writew(addr, Window_Address);
328		ret = ni_readw(Window_Data);
329	}
330	spin_unlock_irqrestore(&devpriv->window_lock, flags);
331
332	return ret;
333}
334
335static struct pnp_device_id device_ids[] = {
336	{.id = "NIC1900", .driver_data = 0},
337	{.id = "NIC2400", .driver_data = 0},
338	{.id = "NIC2500", .driver_data = 0},
339	{.id = "NIC2600", .driver_data = 0},
340	{.id = "NIC2700", .driver_data = 0},
341	{.id = ""}
342};
343
344MODULE_DEVICE_TABLE(pnp, device_ids);
345
346#include "ni_mio_common.c"
347
348static int ni_isapnp_find_board(struct pnp_dev **dev)
349{
350	struct pnp_dev *isapnp_dev = NULL;
351	int i;
352
353	for (i = 0; i < ARRAY_SIZE(ni_boards); i++) {
354		isapnp_dev = pnp_find_dev(NULL,
355					  ISAPNP_VENDOR('N', 'I', 'C'),
356					  ISAPNP_FUNCTION(ni_boards[i].
357							  isapnp_id), NULL);
358
359		if (isapnp_dev == NULL || isapnp_dev->card == NULL)
360			continue;
361
362		if (pnp_device_attach(isapnp_dev) < 0) {
363			printk
364			 ("ni_atmio: %s found but already active, skipping.\n",
365			  ni_boards[i].name);
366			continue;
367		}
368		if (pnp_activate_dev(isapnp_dev) < 0) {
369			pnp_device_detach(isapnp_dev);
370			return -EAGAIN;
371		}
372		if (!pnp_port_valid(isapnp_dev, 0)
373		    || !pnp_irq_valid(isapnp_dev, 0)) {
374			pnp_device_detach(isapnp_dev);
375			printk("ni_atmio: pnp invalid port or irq, aborting\n");
376			return -ENOMEM;
377		}
378		break;
379	}
380	if (i == ARRAY_SIZE(ni_boards))
381		return -ENODEV;
382	*dev = isapnp_dev;
383	return 0;
384}
385
386static int ni_getboardtype(struct comedi_device *dev)
387{
388	int device_id = ni_read_eeprom(dev, 511);
389	int i;
390
391	for (i = 0; i < ARRAY_SIZE(ni_boards); i++) {
392		if (ni_boards[i].device_id == device_id)
393			return i;
394
395	}
396	if (device_id == 255)
397		printk(" can't find board\n");
398	 else if (device_id == 0)
399		printk(" EEPROM read error (?) or device not found\n");
400	 else
401		printk(" unknown device ID %d -- contact author\n", device_id);
402
403	return -1;
404}
405
406static int ni_atmio_attach(struct comedi_device *dev,
407			   struct comedi_devconfig *it)
408{
409	const struct ni_board_struct *boardtype;
410	struct ni_private *devpriv;
411	struct pnp_dev *isapnp_dev;
412	int ret;
413	unsigned long iobase;
414	int board;
415	unsigned int irq;
416
417	ret = ni_alloc_private(dev);
418	if (ret)
419		return ret;
420	devpriv = dev->private;
421
422	devpriv->stc_writew = &ni_atmio_win_out;
423	devpriv->stc_readw = &ni_atmio_win_in;
424	devpriv->stc_writel = &win_out2;
425	devpriv->stc_readl = &win_in2;
426
427	iobase = it->options[0];
428	irq = it->options[1];
429	isapnp_dev = NULL;
430	if (iobase == 0) {
431		ret = ni_isapnp_find_board(&isapnp_dev);
432		if (ret < 0)
433			return ret;
434
435		iobase = pnp_port_start(isapnp_dev, 0);
436		irq = pnp_irq(isapnp_dev, 0);
437		devpriv->isapnp_dev = isapnp_dev;
438	}
439
440	/* reserve our I/O region */
441
442	printk("comedi%d: ni_atmio: 0x%04lx", dev->minor, iobase);
443	if (!request_region(iobase, NI_SIZE, "ni_atmio")) {
444		printk(" I/O port conflict\n");
445		return -EIO;
446	}
447
448	dev->iobase = iobase;
449
450#ifdef DEBUG
451	/* board existence sanity check */
452	{
453		int i;
454
455		printk(" board fingerprint:");
456		for (i = 0; i < 16; i += 2) {
457			printk(" %04x %02x", inw(dev->iobase + i),
458			       inb(dev->iobase + i + 1));
459		}
460	}
461#endif
462
463	/* get board type */
464
465	board = ni_getboardtype(dev);
466	if (board < 0)
467		return -EIO;
468
469	dev->board_ptr = ni_boards + board;
470	boardtype = comedi_board(dev);
471
472	printk(" %s", boardtype->name);
473	dev->board_name = boardtype->name;
474
475	/* irq stuff */
476
477	if (irq != 0) {
478		if (irq > 15 || ni_irqpin[irq] == -1) {
479			printk(" invalid irq %u\n", irq);
480			return -EINVAL;
481		}
482		printk(" ( irq = %u )", irq);
483		ret = request_irq(irq, ni_E_interrupt, NI_E_IRQ_FLAGS,
484				  "ni_atmio", dev);
485
486		if (ret < 0) {
487			printk(" irq not available\n");
488			return -EINVAL;
489		}
490		dev->irq = irq;
491	}
492
493	/* generic E series stuff in ni_mio_common.c */
494
495	ret = ni_E_init(dev);
496	if (ret < 0)
497		return ret;
498
499
500	return 0;
501}
502
503static void ni_atmio_detach(struct comedi_device *dev)
504{
505	struct ni_private *devpriv = dev->private;
506
507	mio_common_detach(dev);
508	if (dev->iobase)
509		release_region(dev->iobase, NI_SIZE);
510	if (dev->irq)
511		free_irq(dev->irq, dev);
512	if (devpriv->isapnp_dev)
513		pnp_device_detach(devpriv->isapnp_dev);
514}
515
516static struct comedi_driver ni_atmio_driver = {
517	.driver_name	= "ni_atmio",
518	.module		= THIS_MODULE,
519	.attach		= ni_atmio_attach,
520	.detach		= ni_atmio_detach,
521};
522module_comedi_driver(ni_atmio_driver);
523