1#ifndef LINUX_SSB_CHIPCO_H_ 2#define LINUX_SSB_CHIPCO_H_ 3 4/* SonicsSiliconBackplane CHIPCOMMON core hardware definitions 5 * 6 * The chipcommon core provides chip identification, SB control, 7 * jtag, 0/1/2 uarts, clock frequency control, a watchdog interrupt timer, 8 * gpio interface, extbus, and support for serial and parallel flashes. 9 * 10 * Copyright 2005, Broadcom Corporation 11 * Copyright 2006, Michael Buesch <m@bues.ch> 12 * 13 * Licensed under the GPL version 2. See COPYING for details. 14 */ 15 16/** ChipCommon core registers. **/ 17 18#define SSB_CHIPCO_CHIPID 0x0000 19#define SSB_CHIPCO_IDMASK 0x0000FFFF 20#define SSB_CHIPCO_REVMASK 0x000F0000 21#define SSB_CHIPCO_REVSHIFT 16 22#define SSB_CHIPCO_PACKMASK 0x00F00000 23#define SSB_CHIPCO_PACKSHIFT 20 24#define SSB_CHIPCO_NRCORESMASK 0x0F000000 25#define SSB_CHIPCO_NRCORESSHIFT 24 26#define SSB_CHIPCO_CAP 0x0004 /* Capabilities */ 27#define SSB_CHIPCO_CAP_NRUART 0x00000003 /* # of UARTs */ 28#define SSB_CHIPCO_CAP_MIPSEB 0x00000004 /* MIPS in BigEndian Mode */ 29#define SSB_CHIPCO_CAP_UARTCLK 0x00000018 /* UART clock select */ 30#define SSB_CHIPCO_CAP_UARTCLK_INT 0x00000008 /* UARTs are driven by internal divided clock */ 31#define SSB_CHIPCO_CAP_UARTGPIO 0x00000020 /* UARTs on GPIO 15-12 */ 32#define SSB_CHIPCO_CAP_EXTBUS 0x000000C0 /* External buses present */ 33#define SSB_CHIPCO_CAP_FLASHT 0x00000700 /* Flash Type */ 34#define SSB_CHIPCO_FLASHT_NONE 0x00000000 /* No flash */ 35#define SSB_CHIPCO_FLASHT_STSER 0x00000100 /* ST serial flash */ 36#define SSB_CHIPCO_FLASHT_ATSER 0x00000200 /* Atmel serial flash */ 37#define SSB_CHIPCO_FLASHT_PARA 0x00000700 /* Parallel flash */ 38#define SSB_CHIPCO_CAP_PLLT 0x00038000 /* PLL Type */ 39#define SSB_PLLTYPE_NONE 0x00000000 40#define SSB_PLLTYPE_1 0x00010000 /* 48Mhz base, 3 dividers */ 41#define SSB_PLLTYPE_2 0x00020000 /* 48Mhz, 4 dividers */ 42#define SSB_PLLTYPE_3 0x00030000 /* 25Mhz, 2 dividers */ 43#define SSB_PLLTYPE_4 0x00008000 /* 48Mhz, 4 dividers */ 44#define SSB_PLLTYPE_5 0x00018000 /* 25Mhz, 4 dividers */ 45#define SSB_PLLTYPE_6 0x00028000 /* 100/200 or 120/240 only */ 46#define SSB_PLLTYPE_7 0x00038000 /* 25Mhz, 4 dividers */ 47#define SSB_CHIPCO_CAP_PCTL 0x00040000 /* Power Control */ 48#define SSB_CHIPCO_CAP_OTPS 0x00380000 /* OTP size */ 49#define SSB_CHIPCO_CAP_OTPS_SHIFT 19 50#define SSB_CHIPCO_CAP_OTPS_BASE 5 51#define SSB_CHIPCO_CAP_JTAGM 0x00400000 /* JTAG master present */ 52#define SSB_CHIPCO_CAP_BROM 0x00800000 /* Internal boot ROM active */ 53#define SSB_CHIPCO_CAP_64BIT 0x08000000 /* 64-bit Backplane */ 54#define SSB_CHIPCO_CAP_PMU 0x10000000 /* PMU available (rev >= 20) */ 55#define SSB_CHIPCO_CAP_ECI 0x20000000 /* ECI available (rev >= 20) */ 56#define SSB_CHIPCO_CAP_SPROM 0x40000000 /* SPROM present */ 57#define SSB_CHIPCO_CORECTL 0x0008 58#define SSB_CHIPCO_CORECTL_UARTCLK0 0x00000001 /* Drive UART with internal clock */ 59#define SSB_CHIPCO_CORECTL_SE 0x00000002 /* sync clk out enable (corerev >= 3) */ 60#define SSB_CHIPCO_CORECTL_UARTCLKEN 0x00000008 /* UART clock enable (rev >= 21) */ 61#define SSB_CHIPCO_BIST 0x000C 62#define SSB_CHIPCO_OTPS 0x0010 /* OTP status */ 63#define SSB_CHIPCO_OTPS_PROGFAIL 0x80000000 64#define SSB_CHIPCO_OTPS_PROTECT 0x00000007 65#define SSB_CHIPCO_OTPS_HW_PROTECT 0x00000001 66#define SSB_CHIPCO_OTPS_SW_PROTECT 0x00000002 67#define SSB_CHIPCO_OTPS_CID_PROTECT 0x00000004 68#define SSB_CHIPCO_OTPC 0x0014 /* OTP control */ 69#define SSB_CHIPCO_OTPC_RECWAIT 0xFF000000 70#define SSB_CHIPCO_OTPC_PROGWAIT 0x00FFFF00 71#define SSB_CHIPCO_OTPC_PRW_SHIFT 8 72#define SSB_CHIPCO_OTPC_MAXFAIL 0x00000038 73#define SSB_CHIPCO_OTPC_VSEL 0x00000006 74#define SSB_CHIPCO_OTPC_SELVL 0x00000001 75#define SSB_CHIPCO_OTPP 0x0018 /* OTP prog */ 76#define SSB_CHIPCO_OTPP_COL 0x000000FF 77#define SSB_CHIPCO_OTPP_ROW 0x0000FF00 78#define SSB_CHIPCO_OTPP_ROW_SHIFT 8 79#define SSB_CHIPCO_OTPP_READERR 0x10000000 80#define SSB_CHIPCO_OTPP_VALUE 0x20000000 81#define SSB_CHIPCO_OTPP_READ 0x40000000 82#define SSB_CHIPCO_OTPP_START 0x80000000 83#define SSB_CHIPCO_OTPP_BUSY 0x80000000 84#define SSB_CHIPCO_IRQSTAT 0x0020 85#define SSB_CHIPCO_IRQMASK 0x0024 86#define SSB_CHIPCO_IRQ_GPIO 0x00000001 /* gpio intr */ 87#define SSB_CHIPCO_IRQ_EXT 0x00000002 /* ro: ext intr pin (corerev >= 3) */ 88#define SSB_CHIPCO_IRQ_WDRESET 0x80000000 /* watchdog reset occurred */ 89#define SSB_CHIPCO_CHIPCTL 0x0028 /* Rev >= 11 only */ 90#define SSB_CHIPCO_CHIPSTAT 0x002C /* Rev >= 11 only */ 91#define SSB_CHIPCO_JCMD 0x0030 /* Rev >= 10 only */ 92#define SSB_CHIPCO_JCMD_START 0x80000000 93#define SSB_CHIPCO_JCMD_BUSY 0x80000000 94#define SSB_CHIPCO_JCMD_PAUSE 0x40000000 95#define SSB_CHIPCO_JCMD0_ACC_MASK 0x0000F000 96#define SSB_CHIPCO_JCMD0_ACC_IRDR 0x00000000 97#define SSB_CHIPCO_JCMD0_ACC_DR 0x00001000 98#define SSB_CHIPCO_JCMD0_ACC_IR 0x00002000 99#define SSB_CHIPCO_JCMD0_ACC_RESET 0x00003000 100#define SSB_CHIPCO_JCMD0_ACC_IRPDR 0x00004000 101#define SSB_CHIPCO_JCMD0_ACC_PDR 0x00005000 102#define SSB_CHIPCO_JCMD0_IRW_MASK 0x00000F00 103#define SSB_CHIPCO_JCMD_ACC_MASK 0x000F0000 /* Changes for corerev 11 */ 104#define SSB_CHIPCO_JCMD_ACC_IRDR 0x00000000 105#define SSB_CHIPCO_JCMD_ACC_DR 0x00010000 106#define SSB_CHIPCO_JCMD_ACC_IR 0x00020000 107#define SSB_CHIPCO_JCMD_ACC_RESET 0x00030000 108#define SSB_CHIPCO_JCMD_ACC_IRPDR 0x00040000 109#define SSB_CHIPCO_JCMD_ACC_PDR 0x00050000 110#define SSB_CHIPCO_JCMD_IRW_MASK 0x00001F00 111#define SSB_CHIPCO_JCMD_IRW_SHIFT 8 112#define SSB_CHIPCO_JCMD_DRW_MASK 0x0000003F 113#define SSB_CHIPCO_JIR 0x0034 /* Rev >= 10 only */ 114#define SSB_CHIPCO_JDR 0x0038 /* Rev >= 10 only */ 115#define SSB_CHIPCO_JCTL 0x003C /* Rev >= 10 only */ 116#define SSB_CHIPCO_JCTL_FORCE_CLK 4 /* Force clock */ 117#define SSB_CHIPCO_JCTL_EXT_EN 2 /* Enable external targets */ 118#define SSB_CHIPCO_JCTL_EN 1 /* Enable Jtag master */ 119#define SSB_CHIPCO_FLASHCTL 0x0040 120#define SSB_CHIPCO_FLASHCTL_START 0x80000000 121#define SSB_CHIPCO_FLASHCTL_BUSY SSB_CHIPCO_FLASHCTL_START 122#define SSB_CHIPCO_FLASHADDR 0x0044 123#define SSB_CHIPCO_FLASHDATA 0x0048 124#define SSB_CHIPCO_BCAST_ADDR 0x0050 125#define SSB_CHIPCO_BCAST_DATA 0x0054 126#define SSB_CHIPCO_GPIOPULLUP 0x0058 /* Rev >= 20 only */ 127#define SSB_CHIPCO_GPIOPULLDOWN 0x005C /* Rev >= 20 only */ 128#define SSB_CHIPCO_GPIOIN 0x0060 129#define SSB_CHIPCO_GPIOOUT 0x0064 130#define SSB_CHIPCO_GPIOOUTEN 0x0068 131#define SSB_CHIPCO_GPIOCTL 0x006C 132#define SSB_CHIPCO_GPIOPOL 0x0070 133#define SSB_CHIPCO_GPIOIRQ 0x0074 134#define SSB_CHIPCO_WATCHDOG 0x0080 135#define SSB_CHIPCO_GPIOTIMER 0x0088 /* LED powersave (corerev >= 16) */ 136#define SSB_CHIPCO_GPIOTIMER_OFFTIME 0x0000FFFF 137#define SSB_CHIPCO_GPIOTIMER_OFFTIME_SHIFT 0 138#define SSB_CHIPCO_GPIOTIMER_ONTIME 0xFFFF0000 139#define SSB_CHIPCO_GPIOTIMER_ONTIME_SHIFT 16 140#define SSB_CHIPCO_GPIOTOUTM 0x008C /* LED powersave (corerev >= 16) */ 141#define SSB_CHIPCO_CLOCK_N 0x0090 142#define SSB_CHIPCO_CLOCK_SB 0x0094 143#define SSB_CHIPCO_CLOCK_PCI 0x0098 144#define SSB_CHIPCO_CLOCK_M2 0x009C 145#define SSB_CHIPCO_CLOCK_MIPS 0x00A0 146#define SSB_CHIPCO_CLKDIV 0x00A4 /* Rev >= 3 only */ 147#define SSB_CHIPCO_CLKDIV_SFLASH 0x0F000000 148#define SSB_CHIPCO_CLKDIV_SFLASH_SHIFT 24 149#define SSB_CHIPCO_CLKDIV_OTP 0x000F0000 150#define SSB_CHIPCO_CLKDIV_OTP_SHIFT 16 151#define SSB_CHIPCO_CLKDIV_JTAG 0x00000F00 152#define SSB_CHIPCO_CLKDIV_JTAG_SHIFT 8 153#define SSB_CHIPCO_CLKDIV_UART 0x000000FF 154#define SSB_CHIPCO_PLLONDELAY 0x00B0 /* Rev >= 4 only */ 155#define SSB_CHIPCO_FREFSELDELAY 0x00B4 /* Rev >= 4 only */ 156#define SSB_CHIPCO_SLOWCLKCTL 0x00B8 /* 6 <= Rev <= 9 only */ 157#define SSB_CHIPCO_SLOWCLKCTL_SRC 0x00000007 /* slow clock source mask */ 158#define SSB_CHIPCO_SLOWCLKCTL_SRC_LPO 0x00000000 /* source of slow clock is LPO */ 159#define SSB_CHIPCO_SLOWCLKCTL_SRC_XTAL 0x00000001 /* source of slow clock is crystal */ 160#define SSB_CHIPCO_SLOECLKCTL_SRC_PCI 0x00000002 /* source of slow clock is PCI */ 161#define SSB_CHIPCO_SLOWCLKCTL_LPOFREQ 0x00000200 /* LPOFreqSel, 1: 160Khz, 0: 32KHz */ 162#define SSB_CHIPCO_SLOWCLKCTL_LPOPD 0x00000400 /* LPOPowerDown, 1: LPO is disabled, 0: LPO is enabled */ 163#define SSB_CHIPCO_SLOWCLKCTL_FSLOW 0x00000800 /* ForceSlowClk, 1: sb/cores running on slow clock, 0: power logic control */ 164#define SSB_CHIPCO_SLOWCLKCTL_IPLL 0x00001000 /* IgnorePllOffReq, 1/0: power logic ignores/honors PLL clock disable requests from core */ 165#define SSB_CHIPCO_SLOWCLKCTL_ENXTAL 0x00002000 /* XtalControlEn, 1/0: power logic does/doesn't disable crystal when appropriate */ 166#define SSB_CHIPCO_SLOWCLKCTL_XTALPU 0x00004000 /* XtalPU (RO), 1/0: crystal running/disabled */ 167#define SSB_CHIPCO_SLOWCLKCTL_CLKDIV 0xFFFF0000 /* ClockDivider (SlowClk = 1/(4+divisor)) */ 168#define SSB_CHIPCO_SLOWCLKCTL_CLKDIV_SHIFT 16 169#define SSB_CHIPCO_SYSCLKCTL 0x00C0 /* Rev >= 3 only */ 170#define SSB_CHIPCO_SYSCLKCTL_IDLPEN 0x00000001 /* ILPen: Enable Idle Low Power */ 171#define SSB_CHIPCO_SYSCLKCTL_ALPEN 0x00000002 /* ALPen: Enable Active Low Power */ 172#define SSB_CHIPCO_SYSCLKCTL_PLLEN 0x00000004 /* ForcePLLOn */ 173#define SSB_CHIPCO_SYSCLKCTL_FORCEALP 0x00000008 /* Force ALP (or HT if ALPen is not set */ 174#define SSB_CHIPCO_SYSCLKCTL_FORCEHT 0x00000010 /* Force HT */ 175#define SSB_CHIPCO_SYSCLKCTL_CLKDIV 0xFFFF0000 /* ClkDiv (ILP = 1/(4+divisor)) */ 176#define SSB_CHIPCO_SYSCLKCTL_CLKDIV_SHIFT 16 177#define SSB_CHIPCO_CLKSTSTR 0x00C4 /* Rev >= 3 only */ 178#define SSB_CHIPCO_PCMCIA_CFG 0x0100 179#define SSB_CHIPCO_PCMCIA_MEMWAIT 0x0104 180#define SSB_CHIPCO_PCMCIA_ATTRWAIT 0x0108 181#define SSB_CHIPCO_PCMCIA_IOWAIT 0x010C 182#define SSB_CHIPCO_IDE_CFG 0x0110 183#define SSB_CHIPCO_IDE_MEMWAIT 0x0114 184#define SSB_CHIPCO_IDE_ATTRWAIT 0x0118 185#define SSB_CHIPCO_IDE_IOWAIT 0x011C 186#define SSB_CHIPCO_PROG_CFG 0x0120 187#define SSB_CHIPCO_PROG_WAITCNT 0x0124 188#define SSB_CHIPCO_FLASH_CFG 0x0128 189#define SSB_CHIPCO_FLASH_WAITCNT 0x012C 190#define SSB_CHIPCO_CLKCTLST 0x01E0 /* Clock control and status (rev >= 20) */ 191#define SSB_CHIPCO_CLKCTLST_FORCEALP 0x00000001 /* Force ALP request */ 192#define SSB_CHIPCO_CLKCTLST_FORCEHT 0x00000002 /* Force HT request */ 193#define SSB_CHIPCO_CLKCTLST_FORCEILP 0x00000004 /* Force ILP request */ 194#define SSB_CHIPCO_CLKCTLST_HAVEALPREQ 0x00000008 /* ALP available request */ 195#define SSB_CHIPCO_CLKCTLST_HAVEHTREQ 0x00000010 /* HT available request */ 196#define SSB_CHIPCO_CLKCTLST_HWCROFF 0x00000020 /* Force HW clock request off */ 197#define SSB_CHIPCO_CLKCTLST_HAVEALP 0x00010000 /* ALP available */ 198#define SSB_CHIPCO_CLKCTLST_HAVEHT 0x00020000 /* HT available */ 199#define SSB_CHIPCO_CLKCTLST_4328A0_HAVEHT 0x00010000 /* 4328a0 has reversed bits */ 200#define SSB_CHIPCO_CLKCTLST_4328A0_HAVEALP 0x00020000 /* 4328a0 has reversed bits */ 201#define SSB_CHIPCO_HW_WORKAROUND 0x01E4 /* Hardware workaround (rev >= 20) */ 202#define SSB_CHIPCO_UART0_DATA 0x0300 203#define SSB_CHIPCO_UART0_IMR 0x0304 204#define SSB_CHIPCO_UART0_FCR 0x0308 205#define SSB_CHIPCO_UART0_LCR 0x030C 206#define SSB_CHIPCO_UART0_MCR 0x0310 207#define SSB_CHIPCO_UART0_LSR 0x0314 208#define SSB_CHIPCO_UART0_MSR 0x0318 209#define SSB_CHIPCO_UART0_SCRATCH 0x031C 210#define SSB_CHIPCO_UART1_DATA 0x0400 211#define SSB_CHIPCO_UART1_IMR 0x0404 212#define SSB_CHIPCO_UART1_FCR 0x0408 213#define SSB_CHIPCO_UART1_LCR 0x040C 214#define SSB_CHIPCO_UART1_MCR 0x0410 215#define SSB_CHIPCO_UART1_LSR 0x0414 216#define SSB_CHIPCO_UART1_MSR 0x0418 217#define SSB_CHIPCO_UART1_SCRATCH 0x041C 218/* PMU registers (rev >= 20) */ 219#define SSB_CHIPCO_PMU_CTL 0x0600 /* PMU control */ 220#define SSB_CHIPCO_PMU_CTL_ILP_DIV 0xFFFF0000 /* ILP div mask */ 221#define SSB_CHIPCO_PMU_CTL_ILP_DIV_SHIFT 16 222#define SSB_CHIPCO_PMU_CTL_PLL_UPD 0x00000400 223#define SSB_CHIPCO_PMU_CTL_NOILPONW 0x00000200 /* No ILP on wait */ 224#define SSB_CHIPCO_PMU_CTL_HTREQEN 0x00000100 /* HT req enable */ 225#define SSB_CHIPCO_PMU_CTL_ALPREQEN 0x00000080 /* ALP req enable */ 226#define SSB_CHIPCO_PMU_CTL_XTALFREQ 0x0000007C /* Crystal freq */ 227#define SSB_CHIPCO_PMU_CTL_XTALFREQ_SHIFT 2 228#define SSB_CHIPCO_PMU_CTL_ILPDIVEN 0x00000002 /* ILP div enable */ 229#define SSB_CHIPCO_PMU_CTL_LPOSEL 0x00000001 /* LPO sel */ 230#define SSB_CHIPCO_PMU_CAP 0x0604 /* PMU capabilities */ 231#define SSB_CHIPCO_PMU_CAP_REVISION 0x000000FF /* Revision mask */ 232#define SSB_CHIPCO_PMU_STAT 0x0608 /* PMU status */ 233#define SSB_CHIPCO_PMU_STAT_INTPEND 0x00000040 /* Interrupt pending */ 234#define SSB_CHIPCO_PMU_STAT_SBCLKST 0x00000030 /* Backplane clock status? */ 235#define SSB_CHIPCO_PMU_STAT_HAVEALP 0x00000008 /* ALP available */ 236#define SSB_CHIPCO_PMU_STAT_HAVEHT 0x00000004 /* HT available */ 237#define SSB_CHIPCO_PMU_STAT_RESINIT 0x00000003 /* Res init */ 238#define SSB_CHIPCO_PMU_RES_STAT 0x060C /* PMU res status */ 239#define SSB_CHIPCO_PMU_RES_PEND 0x0610 /* PMU res pending */ 240#define SSB_CHIPCO_PMU_TIMER 0x0614 /* PMU timer */ 241#define SSB_CHIPCO_PMU_MINRES_MSK 0x0618 /* PMU min res mask */ 242#define SSB_CHIPCO_PMU_MAXRES_MSK 0x061C /* PMU max res mask */ 243#define SSB_CHIPCO_PMU_RES_TABSEL 0x0620 /* PMU res table sel */ 244#define SSB_CHIPCO_PMU_RES_DEPMSK 0x0624 /* PMU res dep mask */ 245#define SSB_CHIPCO_PMU_RES_UPDNTM 0x0628 /* PMU res updown timer */ 246#define SSB_CHIPCO_PMU_RES_TIMER 0x062C /* PMU res timer */ 247#define SSB_CHIPCO_PMU_CLKSTRETCH 0x0630 /* PMU clockstretch */ 248#define SSB_CHIPCO_PMU_WATCHDOG 0x0634 /* PMU watchdog */ 249#define SSB_CHIPCO_PMU_RES_REQTS 0x0640 /* PMU res req timer sel */ 250#define SSB_CHIPCO_PMU_RES_REQT 0x0644 /* PMU res req timer */ 251#define SSB_CHIPCO_PMU_RES_REQM 0x0648 /* PMU res req mask */ 252#define SSB_CHIPCO_CHIPCTL_ADDR 0x0650 253#define SSB_CHIPCO_CHIPCTL_DATA 0x0654 254#define SSB_CHIPCO_REGCTL_ADDR 0x0658 255#define SSB_CHIPCO_REGCTL_DATA 0x065C 256#define SSB_CHIPCO_PLLCTL_ADDR 0x0660 257#define SSB_CHIPCO_PLLCTL_DATA 0x0664 258 259 260 261/** PMU PLL registers */ 262 263/* PMU rev 0 PLL registers */ 264#define SSB_PMU0_PLLCTL0 0 265#define SSB_PMU0_PLLCTL0_PDIV_MSK 0x00000001 266#define SSB_PMU0_PLLCTL0_PDIV_FREQ 25000 /* kHz */ 267#define SSB_PMU0_PLLCTL1 1 268#define SSB_PMU0_PLLCTL1_WILD_IMSK 0xF0000000 /* Wild int mask (low nibble) */ 269#define SSB_PMU0_PLLCTL1_WILD_IMSK_SHIFT 28 270#define SSB_PMU0_PLLCTL1_WILD_FMSK 0x0FFFFF00 /* Wild frac mask */ 271#define SSB_PMU0_PLLCTL1_WILD_FMSK_SHIFT 8 272#define SSB_PMU0_PLLCTL1_STOPMOD 0x00000040 /* Stop mod */ 273#define SSB_PMU0_PLLCTL2 2 274#define SSB_PMU0_PLLCTL2_WILD_IMSKHI 0x0000000F /* Wild int mask (high nibble) */ 275#define SSB_PMU0_PLLCTL2_WILD_IMSKHI_SHIFT 0 276 277/* PMU rev 1 PLL registers */ 278#define SSB_PMU1_PLLCTL0 0 279#define SSB_PMU1_PLLCTL0_P1DIV 0x00F00000 /* P1 div */ 280#define SSB_PMU1_PLLCTL0_P1DIV_SHIFT 20 281#define SSB_PMU1_PLLCTL0_P2DIV 0x0F000000 /* P2 div */ 282#define SSB_PMU1_PLLCTL0_P2DIV_SHIFT 24 283#define SSB_PMU1_PLLCTL1 1 284#define SSB_PMU1_PLLCTL1_M1DIV 0x000000FF /* M1 div */ 285#define SSB_PMU1_PLLCTL1_M1DIV_SHIFT 0 286#define SSB_PMU1_PLLCTL1_M2DIV 0x0000FF00 /* M2 div */ 287#define SSB_PMU1_PLLCTL1_M2DIV_SHIFT 8 288#define SSB_PMU1_PLLCTL1_M3DIV 0x00FF0000 /* M3 div */ 289#define SSB_PMU1_PLLCTL1_M3DIV_SHIFT 16 290#define SSB_PMU1_PLLCTL1_M4DIV 0xFF000000 /* M4 div */ 291#define SSB_PMU1_PLLCTL1_M4DIV_SHIFT 24 292#define SSB_PMU1_PLLCTL2 2 293#define SSB_PMU1_PLLCTL2_M5DIV 0x000000FF /* M5 div */ 294#define SSB_PMU1_PLLCTL2_M5DIV_SHIFT 0 295#define SSB_PMU1_PLLCTL2_M6DIV 0x0000FF00 /* M6 div */ 296#define SSB_PMU1_PLLCTL2_M6DIV_SHIFT 8 297#define SSB_PMU1_PLLCTL2_NDIVMODE 0x000E0000 /* NDIV mode */ 298#define SSB_PMU1_PLLCTL2_NDIVMODE_SHIFT 17 299#define SSB_PMU1_PLLCTL2_NDIVINT 0x1FF00000 /* NDIV int */ 300#define SSB_PMU1_PLLCTL2_NDIVINT_SHIFT 20 301#define SSB_PMU1_PLLCTL3 3 302#define SSB_PMU1_PLLCTL3_NDIVFRAC 0x00FFFFFF /* NDIV frac */ 303#define SSB_PMU1_PLLCTL3_NDIVFRAC_SHIFT 0 304#define SSB_PMU1_PLLCTL4 4 305#define SSB_PMU1_PLLCTL5 5 306#define SSB_PMU1_PLLCTL5_CLKDRV 0xFFFFFF00 /* clk drv */ 307#define SSB_PMU1_PLLCTL5_CLKDRV_SHIFT 8 308 309/* BCM4312 PLL resource numbers. */ 310#define SSB_PMURES_4312_SWITCHER_BURST 0 311#define SSB_PMURES_4312_SWITCHER_PWM 1 312#define SSB_PMURES_4312_PA_REF_LDO 2 313#define SSB_PMURES_4312_CORE_LDO_BURST 3 314#define SSB_PMURES_4312_CORE_LDO_PWM 4 315#define SSB_PMURES_4312_RADIO_LDO 5 316#define SSB_PMURES_4312_ILP_REQUEST 6 317#define SSB_PMURES_4312_BG_FILTBYP 7 318#define SSB_PMURES_4312_TX_FILTBYP 8 319#define SSB_PMURES_4312_RX_FILTBYP 9 320#define SSB_PMURES_4312_XTAL_PU 10 321#define SSB_PMURES_4312_ALP_AVAIL 11 322#define SSB_PMURES_4312_BB_PLL_FILTBYP 12 323#define SSB_PMURES_4312_RF_PLL_FILTBYP 13 324#define SSB_PMURES_4312_HT_AVAIL 14 325 326/* BCM4325 PLL resource numbers. */ 327#define SSB_PMURES_4325_BUCK_BOOST_BURST 0 328#define SSB_PMURES_4325_CBUCK_BURST 1 329#define SSB_PMURES_4325_CBUCK_PWM 2 330#define SSB_PMURES_4325_CLDO_CBUCK_BURST 3 331#define SSB_PMURES_4325_CLDO_CBUCK_PWM 4 332#define SSB_PMURES_4325_BUCK_BOOST_PWM 5 333#define SSB_PMURES_4325_ILP_REQUEST 6 334#define SSB_PMURES_4325_ABUCK_BURST 7 335#define SSB_PMURES_4325_ABUCK_PWM 8 336#define SSB_PMURES_4325_LNLDO1_PU 9 337#define SSB_PMURES_4325_LNLDO2_PU 10 338#define SSB_PMURES_4325_LNLDO3_PU 11 339#define SSB_PMURES_4325_LNLDO4_PU 12 340#define SSB_PMURES_4325_XTAL_PU 13 341#define SSB_PMURES_4325_ALP_AVAIL 14 342#define SSB_PMURES_4325_RX_PWRSW_PU 15 343#define SSB_PMURES_4325_TX_PWRSW_PU 16 344#define SSB_PMURES_4325_RFPLL_PWRSW_PU 17 345#define SSB_PMURES_4325_LOGEN_PWRSW_PU 18 346#define SSB_PMURES_4325_AFE_PWRSW_PU 19 347#define SSB_PMURES_4325_BBPLL_PWRSW_PU 20 348#define SSB_PMURES_4325_HT_AVAIL 21 349 350/* BCM4328 PLL resource numbers. */ 351#define SSB_PMURES_4328_EXT_SWITCHER_PWM 0 352#define SSB_PMURES_4328_BB_SWITCHER_PWM 1 353#define SSB_PMURES_4328_BB_SWITCHER_BURST 2 354#define SSB_PMURES_4328_BB_EXT_SWITCHER_BURST 3 355#define SSB_PMURES_4328_ILP_REQUEST 4 356#define SSB_PMURES_4328_RADIO_SWITCHER_PWM 5 357#define SSB_PMURES_4328_RADIO_SWITCHER_BURST 6 358#define SSB_PMURES_4328_ROM_SWITCH 7 359#define SSB_PMURES_4328_PA_REF_LDO 8 360#define SSB_PMURES_4328_RADIO_LDO 9 361#define SSB_PMURES_4328_AFE_LDO 10 362#define SSB_PMURES_4328_PLL_LDO 11 363#define SSB_PMURES_4328_BG_FILTBYP 12 364#define SSB_PMURES_4328_TX_FILTBYP 13 365#define SSB_PMURES_4328_RX_FILTBYP 14 366#define SSB_PMURES_4328_XTAL_PU 15 367#define SSB_PMURES_4328_XTAL_EN 16 368#define SSB_PMURES_4328_BB_PLL_FILTBYP 17 369#define SSB_PMURES_4328_RF_PLL_FILTBYP 18 370#define SSB_PMURES_4328_BB_PLL_PU 19 371 372/* BCM5354 PLL resource numbers. */ 373#define SSB_PMURES_5354_EXT_SWITCHER_PWM 0 374#define SSB_PMURES_5354_BB_SWITCHER_PWM 1 375#define SSB_PMURES_5354_BB_SWITCHER_BURST 2 376#define SSB_PMURES_5354_BB_EXT_SWITCHER_BURST 3 377#define SSB_PMURES_5354_ILP_REQUEST 4 378#define SSB_PMURES_5354_RADIO_SWITCHER_PWM 5 379#define SSB_PMURES_5354_RADIO_SWITCHER_BURST 6 380#define SSB_PMURES_5354_ROM_SWITCH 7 381#define SSB_PMURES_5354_PA_REF_LDO 8 382#define SSB_PMURES_5354_RADIO_LDO 9 383#define SSB_PMURES_5354_AFE_LDO 10 384#define SSB_PMURES_5354_PLL_LDO 11 385#define SSB_PMURES_5354_BG_FILTBYP 12 386#define SSB_PMURES_5354_TX_FILTBYP 13 387#define SSB_PMURES_5354_RX_FILTBYP 14 388#define SSB_PMURES_5354_XTAL_PU 15 389#define SSB_PMURES_5354_XTAL_EN 16 390#define SSB_PMURES_5354_BB_PLL_FILTBYP 17 391#define SSB_PMURES_5354_RF_PLL_FILTBYP 18 392#define SSB_PMURES_5354_BB_PLL_PU 19 393 394 395 396/** Chip specific Chip-Status register contents. */ 397#define SSB_CHIPCO_CHST_4322_SPROM_EXISTS 0x00000040 /* SPROM present */ 398#define SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL 0x00000003 399#define SSB_CHIPCO_CHST_4325_DEFCIS_SEL 0 /* OTP is powered up, use def. CIS, no SPROM */ 400#define SSB_CHIPCO_CHST_4325_SPROM_SEL 1 /* OTP is powered up, SPROM is present */ 401#define SSB_CHIPCO_CHST_4325_OTP_SEL 2 /* OTP is powered up, no SPROM */ 402#define SSB_CHIPCO_CHST_4325_OTP_PWRDN 3 /* OTP is powered down, SPROM is present */ 403#define SSB_CHIPCO_CHST_4325_SDIO_USB_MODE 0x00000004 404#define SSB_CHIPCO_CHST_4325_SDIO_USB_MODE_SHIFT 2 405#define SSB_CHIPCO_CHST_4325_RCAL_VALID 0x00000008 406#define SSB_CHIPCO_CHST_4325_RCAL_VALID_SHIFT 3 407#define SSB_CHIPCO_CHST_4325_RCAL_VALUE 0x000001F0 408#define SSB_CHIPCO_CHST_4325_RCAL_VALUE_SHIFT 4 409#define SSB_CHIPCO_CHST_4325_PMUTOP_2B 0x00000200 /* 1 for 2b, 0 for to 2a */ 410 411/** Macros to determine SPROM presence based on Chip-Status register. */ 412#define SSB_CHIPCO_CHST_4312_SPROM_PRESENT(status) \ 413 ((status & SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL) != \ 414 SSB_CHIPCO_CHST_4325_OTP_SEL) 415#define SSB_CHIPCO_CHST_4322_SPROM_PRESENT(status) \ 416 (status & SSB_CHIPCO_CHST_4322_SPROM_EXISTS) 417#define SSB_CHIPCO_CHST_4325_SPROM_PRESENT(status) \ 418 (((status & SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL) != \ 419 SSB_CHIPCO_CHST_4325_DEFCIS_SEL) && \ 420 ((status & SSB_CHIPCO_CHST_4325_SPROM_OTP_SEL) != \ 421 SSB_CHIPCO_CHST_4325_OTP_SEL)) 422 423 424 425/** Clockcontrol masks and values **/ 426 427/* SSB_CHIPCO_CLOCK_N */ 428#define SSB_CHIPCO_CLK_N1 0x0000003F /* n1 control */ 429#define SSB_CHIPCO_CLK_N2 0x00003F00 /* n2 control */ 430#define SSB_CHIPCO_CLK_N2_SHIFT 8 431#define SSB_CHIPCO_CLK_PLLC 0x000F0000 /* pll control */ 432#define SSB_CHIPCO_CLK_PLLC_SHIFT 16 433 434/* SSB_CHIPCO_CLOCK_SB/PCI/UART */ 435#define SSB_CHIPCO_CLK_M1 0x0000003F /* m1 control */ 436#define SSB_CHIPCO_CLK_M2 0x00003F00 /* m2 control */ 437#define SSB_CHIPCO_CLK_M2_SHIFT 8 438#define SSB_CHIPCO_CLK_M3 0x003F0000 /* m3 control */ 439#define SSB_CHIPCO_CLK_M3_SHIFT 16 440#define SSB_CHIPCO_CLK_MC 0x1F000000 /* mux control */ 441#define SSB_CHIPCO_CLK_MC_SHIFT 24 442 443/* N3M Clock control magic field values */ 444#define SSB_CHIPCO_CLK_F6_2 0x02 /* A factor of 2 in */ 445#define SSB_CHIPCO_CLK_F6_3 0x03 /* 6-bit fields like */ 446#define SSB_CHIPCO_CLK_F6_4 0x05 /* N1, M1 or M3 */ 447#define SSB_CHIPCO_CLK_F6_5 0x09 448#define SSB_CHIPCO_CLK_F6_6 0x11 449#define SSB_CHIPCO_CLK_F6_7 0x21 450 451#define SSB_CHIPCO_CLK_F5_BIAS 5 /* 5-bit fields get this added */ 452 453#define SSB_CHIPCO_CLK_MC_BYPASS 0x08 454#define SSB_CHIPCO_CLK_MC_M1 0x04 455#define SSB_CHIPCO_CLK_MC_M1M2 0x02 456#define SSB_CHIPCO_CLK_MC_M1M2M3 0x01 457#define SSB_CHIPCO_CLK_MC_M1M3 0x11 458 459/* Type 2 Clock control magic field values */ 460#define SSB_CHIPCO_CLK_T2_BIAS 2 /* n1, n2, m1 & m3 bias */ 461#define SSB_CHIPCO_CLK_T2M2_BIAS 3 /* m2 bias */ 462 463#define SSB_CHIPCO_CLK_T2MC_M1BYP 1 464#define SSB_CHIPCO_CLK_T2MC_M2BYP 2 465#define SSB_CHIPCO_CLK_T2MC_M3BYP 4 466 467/* Type 6 Clock control magic field values */ 468#define SSB_CHIPCO_CLK_T6_MMASK 1 /* bits of interest in m */ 469#define SSB_CHIPCO_CLK_T6_M0 120000000 /* sb clock for m = 0 */ 470#define SSB_CHIPCO_CLK_T6_M1 100000000 /* sb clock for m = 1 */ 471#define SSB_CHIPCO_CLK_SB2MIPS_T6(sb) (2 * (sb)) 472 473/* Common clock base */ 474#define SSB_CHIPCO_CLK_BASE1 24000000 /* Half the clock freq */ 475#define SSB_CHIPCO_CLK_BASE2 12500000 /* Alternate crystal on some PLL's */ 476 477/* Clock control values for 200Mhz in 5350 */ 478#define SSB_CHIPCO_CLK_5350_N 0x0311 479#define SSB_CHIPCO_CLK_5350_M 0x04020009 480 481 482/** Bits in the config registers **/ 483 484#define SSB_CHIPCO_CFG_EN 0x0001 /* Enable */ 485#define SSB_CHIPCO_CFG_EXTM 0x000E /* Extif Mode */ 486#define SSB_CHIPCO_CFG_EXTM_ASYNC 0x0002 /* Async/Parallel flash */ 487#define SSB_CHIPCO_CFG_EXTM_SYNC 0x0004 /* Synchronous */ 488#define SSB_CHIPCO_CFG_EXTM_PCMCIA 0x0008 /* PCMCIA */ 489#define SSB_CHIPCO_CFG_EXTM_IDE 0x000A /* IDE */ 490#define SSB_CHIPCO_CFG_DS16 0x0010 /* Data size, 0=8bit, 1=16bit */ 491#define SSB_CHIPCO_CFG_CLKDIV 0x0060 /* Sync: Clock divisor */ 492#define SSB_CHIPCO_CFG_CLKEN 0x0080 /* Sync: Clock enable */ 493#define SSB_CHIPCO_CFG_BSTRO 0x0100 /* Sync: Size/Bytestrobe */ 494 495 496/** Flash-specific control/status values */ 497 498/* flashcontrol opcodes for ST flashes */ 499#define SSB_CHIPCO_FLASHCTL_ST_WREN 0x0006 /* Write Enable */ 500#define SSB_CHIPCO_FLASHCTL_ST_WRDIS 0x0004 /* Write Disable */ 501#define SSB_CHIPCO_FLASHCTL_ST_RDSR 0x0105 /* Read Status Register */ 502#define SSB_CHIPCO_FLASHCTL_ST_WRSR 0x0101 /* Write Status Register */ 503#define SSB_CHIPCO_FLASHCTL_ST_READ 0x0303 /* Read Data Bytes */ 504#define SSB_CHIPCO_FLASHCTL_ST_PP 0x0302 /* Page Program */ 505#define SSB_CHIPCO_FLASHCTL_ST_SE 0x02D8 /* Sector Erase */ 506#define SSB_CHIPCO_FLASHCTL_ST_BE 0x00C7 /* Bulk Erase */ 507#define SSB_CHIPCO_FLASHCTL_ST_DP 0x00B9 /* Deep Power-down */ 508#define SSB_CHIPCO_FLASHCTL_ST_RES 0x03AB /* Read Electronic Signature */ 509#define SSB_CHIPCO_FLASHCTL_ST_CSA 0x1000 /* Keep chip select asserted */ 510#define SSB_CHIPCO_FLASHCTL_ST_SSE 0x0220 /* Sub-sector Erase */ 511 512/* Status register bits for ST flashes */ 513#define SSB_CHIPCO_FLASHSTA_ST_WIP 0x01 /* Write In Progress */ 514#define SSB_CHIPCO_FLASHSTA_ST_WEL 0x02 /* Write Enable Latch */ 515#define SSB_CHIPCO_FLASHSTA_ST_BP 0x1C /* Block Protect */ 516#define SSB_CHIPCO_FLASHSTA_ST_BP_SHIFT 2 517#define SSB_CHIPCO_FLASHSTA_ST_SRWD 0x80 /* Status Register Write Disable */ 518 519/* flashcontrol opcodes for Atmel flashes */ 520#define SSB_CHIPCO_FLASHCTL_AT_READ 0x07E8 521#define SSB_CHIPCO_FLASHCTL_AT_PAGE_READ 0x07D2 522#define SSB_CHIPCO_FLASHCTL_AT_BUF1_READ /* FIXME */ 523#define SSB_CHIPCO_FLASHCTL_AT_BUF2_READ /* FIXME */ 524#define SSB_CHIPCO_FLASHCTL_AT_STATUS 0x01D7 525#define SSB_CHIPCO_FLASHCTL_AT_BUF1_WRITE 0x0384 526#define SSB_CHIPCO_FLASHCTL_AT_BUF2_WRITE 0x0387 527#define SSB_CHIPCO_FLASHCTL_AT_BUF1_ERASE_PRGM 0x0283 /* Erase program */ 528#define SSB_CHIPCO_FLASHCTL_AT_BUF2_ERASE_PRGM 0x0286 /* Erase program */ 529#define SSB_CHIPCO_FLASHCTL_AT_BUF1_PROGRAM 0x0288 530#define SSB_CHIPCO_FLASHCTL_AT_BUF2_PROGRAM 0x0289 531#define SSB_CHIPCO_FLASHCTL_AT_PAGE_ERASE 0x0281 532#define SSB_CHIPCO_FLASHCTL_AT_BLOCK_ERASE 0x0250 533#define SSB_CHIPCO_FLASHCTL_AT_BUF1_WRER_PRGM 0x0382 /* Write erase program */ 534#define SSB_CHIPCO_FLASHCTL_AT_BUF2_WRER_PRGM 0x0385 /* Write erase program */ 535#define SSB_CHIPCO_FLASHCTL_AT_BUF1_LOAD 0x0253 536#define SSB_CHIPCO_FLASHCTL_AT_BUF2_LOAD 0x0255 537#define SSB_CHIPCO_FLASHCTL_AT_BUF1_COMPARE 0x0260 538#define SSB_CHIPCO_FLASHCTL_AT_BUF2_COMPARE 0x0261 539#define SSB_CHIPCO_FLASHCTL_AT_BUF1_REPROGRAM 0x0258 540#define SSB_CHIPCO_FLASHCTL_AT_BUF2_REPROGRAM 0x0259 541 542/* Status register bits for Atmel flashes */ 543#define SSB_CHIPCO_FLASHSTA_AT_READY 0x80 544#define SSB_CHIPCO_FLASHSTA_AT_MISMATCH 0x40 545#define SSB_CHIPCO_FLASHSTA_AT_ID 0x38 546#define SSB_CHIPCO_FLASHSTA_AT_ID_SHIFT 3 547 548 549/** OTP **/ 550 551/* OTP regions */ 552#define SSB_CHIPCO_OTP_HW_REGION SSB_CHIPCO_OTPS_HW_PROTECT 553#define SSB_CHIPCO_OTP_SW_REGION SSB_CHIPCO_OTPS_SW_PROTECT 554#define SSB_CHIPCO_OTP_CID_REGION SSB_CHIPCO_OTPS_CID_PROTECT 555 556/* OTP regions (Byte offsets from otp size) */ 557#define SSB_CHIPCO_OTP_SWLIM_OFF (-8) 558#define SSB_CHIPCO_OTP_CIDBASE_OFF 0 559#define SSB_CHIPCO_OTP_CIDLIM_OFF 8 560 561/* Predefined OTP words (Word offset from otp size) */ 562#define SSB_CHIPCO_OTP_BOUNDARY_OFF (-4) 563#define SSB_CHIPCO_OTP_HWSIGN_OFF (-3) 564#define SSB_CHIPCO_OTP_SWSIGN_OFF (-2) 565#define SSB_CHIPCO_OTP_CIDSIGN_OFF (-1) 566 567#define SSB_CHIPCO_OTP_CID_OFF 0 568#define SSB_CHIPCO_OTP_PKG_OFF 1 569#define SSB_CHIPCO_OTP_FID_OFF 2 570#define SSB_CHIPCO_OTP_RSV_OFF 3 571#define SSB_CHIPCO_OTP_LIM_OFF 4 572 573#define SSB_CHIPCO_OTP_SIGNATURE 0x578A 574#define SSB_CHIPCO_OTP_MAGIC 0x4E56 575 576 577struct ssb_device; 578struct ssb_serial_port; 579 580/* Data for the PMU, if available. 581 * Check availability with ((struct ssb_chipcommon)->capabilities & SSB_CHIPCO_CAP_PMU) 582 */ 583struct ssb_chipcommon_pmu { 584 u8 rev; /* PMU revision */ 585 u32 crystalfreq; /* The active crystal frequency (in kHz) */ 586}; 587 588struct ssb_chipcommon { 589 struct ssb_device *dev; 590 u32 capabilities; 591 u32 status; 592 /* Fast Powerup Delay constant */ 593 u16 fast_pwrup_delay; 594 spinlock_t gpio_lock; 595 struct ssb_chipcommon_pmu pmu; 596 u32 ticks_per_ms; 597 u32 max_timer_ms; 598}; 599 600static inline bool ssb_chipco_available(struct ssb_chipcommon *cc) 601{ 602 return (cc->dev != NULL); 603} 604 605/* Register access */ 606#define chipco_read32(cc, offset) ssb_read32((cc)->dev, offset) 607#define chipco_write32(cc, offset, val) ssb_write32((cc)->dev, offset, val) 608 609#define chipco_mask32(cc, offset, mask) \ 610 chipco_write32(cc, offset, chipco_read32(cc, offset) & (mask)) 611#define chipco_set32(cc, offset, set) \ 612 chipco_write32(cc, offset, chipco_read32(cc, offset) | (set)) 613#define chipco_maskset32(cc, offset, mask, set) \ 614 chipco_write32(cc, offset, (chipco_read32(cc, offset) & (mask)) | (set)) 615 616extern void ssb_chipcommon_init(struct ssb_chipcommon *cc); 617 618extern void ssb_chipco_suspend(struct ssb_chipcommon *cc); 619extern void ssb_chipco_resume(struct ssb_chipcommon *cc); 620 621extern void ssb_chipco_get_clockcpu(struct ssb_chipcommon *cc, 622 u32 *plltype, u32 *n, u32 *m); 623extern void ssb_chipco_get_clockcontrol(struct ssb_chipcommon *cc, 624 u32 *plltype, u32 *n, u32 *m); 625extern void ssb_chipco_timing_init(struct ssb_chipcommon *cc, 626 unsigned long ns_per_cycle); 627 628enum ssb_clkmode { 629 SSB_CLKMODE_SLOW, 630 SSB_CLKMODE_FAST, 631 SSB_CLKMODE_DYNAMIC, 632}; 633 634extern void ssb_chipco_set_clockmode(struct ssb_chipcommon *cc, 635 enum ssb_clkmode mode); 636 637extern u32 ssb_chipco_watchdog_timer_set(struct ssb_chipcommon *cc, u32 ticks); 638 639void ssb_chipco_irq_mask(struct ssb_chipcommon *cc, u32 mask, u32 value); 640 641u32 ssb_chipco_irq_status(struct ssb_chipcommon *cc, u32 mask); 642 643/* Chipcommon GPIO pin access. */ 644u32 ssb_chipco_gpio_in(struct ssb_chipcommon *cc, u32 mask); 645u32 ssb_chipco_gpio_out(struct ssb_chipcommon *cc, u32 mask, u32 value); 646u32 ssb_chipco_gpio_outen(struct ssb_chipcommon *cc, u32 mask, u32 value); 647u32 ssb_chipco_gpio_control(struct ssb_chipcommon *cc, u32 mask, u32 value); 648u32 ssb_chipco_gpio_intmask(struct ssb_chipcommon *cc, u32 mask, u32 value); 649u32 ssb_chipco_gpio_polarity(struct ssb_chipcommon *cc, u32 mask, u32 value); 650u32 ssb_chipco_gpio_pullup(struct ssb_chipcommon *cc, u32 mask, u32 value); 651u32 ssb_chipco_gpio_pulldown(struct ssb_chipcommon *cc, u32 mask, u32 value); 652 653#ifdef CONFIG_SSB_SERIAL 654extern int ssb_chipco_serial_init(struct ssb_chipcommon *cc, 655 struct ssb_serial_port *ports); 656#endif /* CONFIG_SSB_SERIAL */ 657 658/* PMU support */ 659extern void ssb_pmu_init(struct ssb_chipcommon *cc); 660 661enum ssb_pmu_ldo_volt_id { 662 LDO_PAREF = 0, 663 LDO_VOLT1, 664 LDO_VOLT2, 665 LDO_VOLT3, 666}; 667 668void ssb_pmu_set_ldo_voltage(struct ssb_chipcommon *cc, 669 enum ssb_pmu_ldo_volt_id id, u32 voltage); 670void ssb_pmu_set_ldo_paref(struct ssb_chipcommon *cc, bool on); 671void ssb_pmu_spuravoid_pllupdate(struct ssb_chipcommon *cc, int spuravoid); 672 673#endif /* LINUX_SSB_CHIPCO_H_ */ 674