mac80211.h revision 3ea542d3c2862142ae511fac5ce2dfc7419dcc53
1/* 2 * mac80211 <-> driver interface 3 * 4 * Copyright 2002-2005, Devicescape Software, Inc. 5 * Copyright 2006-2007 Jiri Benc <jbenc@suse.cz> 6 * Copyright 2007-2010 Johannes Berg <johannes@sipsolutions.net> 7 * 8 * This program is free software; you can redistribute it and/or modify 9 * it under the terms of the GNU General Public License version 2 as 10 * published by the Free Software Foundation. 11 */ 12 13#ifndef MAC80211_H 14#define MAC80211_H 15 16#include <linux/kernel.h> 17#include <linux/if_ether.h> 18#include <linux/skbuff.h> 19#include <linux/wireless.h> 20#include <linux/device.h> 21#include <linux/ieee80211.h> 22#include <net/cfg80211.h> 23 24/** 25 * DOC: Introduction 26 * 27 * mac80211 is the Linux stack for 802.11 hardware that implements 28 * only partial functionality in hard- or firmware. This document 29 * defines the interface between mac80211 and low-level hardware 30 * drivers. 31 */ 32 33/** 34 * DOC: Calling mac80211 from interrupts 35 * 36 * Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be 37 * called in hardware interrupt context. The low-level driver must not call any 38 * other functions in hardware interrupt context. If there is a need for such 39 * call, the low-level driver should first ACK the interrupt and perform the 40 * IEEE 802.11 code call after this, e.g. from a scheduled workqueue or even 41 * tasklet function. 42 * 43 * NOTE: If the driver opts to use the _irqsafe() functions, it may not also 44 * use the non-IRQ-safe functions! 45 */ 46 47/** 48 * DOC: Warning 49 * 50 * If you're reading this document and not the header file itself, it will 51 * be incomplete because not all documentation has been converted yet. 52 */ 53 54/** 55 * DOC: Frame format 56 * 57 * As a general rule, when frames are passed between mac80211 and the driver, 58 * they start with the IEEE 802.11 header and include the same octets that are 59 * sent over the air except for the FCS which should be calculated by the 60 * hardware. 61 * 62 * There are, however, various exceptions to this rule for advanced features: 63 * 64 * The first exception is for hardware encryption and decryption offload 65 * where the IV/ICV may or may not be generated in hardware. 66 * 67 * Secondly, when the hardware handles fragmentation, the frame handed to 68 * the driver from mac80211 is the MSDU, not the MPDU. 69 * 70 * Finally, for received frames, the driver is able to indicate that it has 71 * filled a radiotap header and put that in front of the frame; if it does 72 * not do so then mac80211 may add this under certain circumstances. 73 */ 74 75/** 76 * DOC: mac80211 workqueue 77 * 78 * mac80211 provides its own workqueue for drivers and internal mac80211 use. 79 * The workqueue is a single threaded workqueue and can only be accessed by 80 * helpers for sanity checking. Drivers must ensure all work added onto the 81 * mac80211 workqueue should be cancelled on the driver stop() callback. 82 * 83 * mac80211 will flushed the workqueue upon interface removal and during 84 * suspend. 85 * 86 * All work performed on the mac80211 workqueue must not acquire the RTNL lock. 87 * 88 */ 89 90/** 91 * enum ieee80211_max_queues - maximum number of queues 92 * 93 * @IEEE80211_MAX_QUEUES: Maximum number of regular device queues. 94 */ 95enum ieee80211_max_queues { 96 IEEE80211_MAX_QUEUES = 4, 97}; 98 99/** 100 * enum ieee80211_ac_numbers - AC numbers as used in mac80211 101 * @IEEE80211_AC_VO: voice 102 * @IEEE80211_AC_VI: video 103 * @IEEE80211_AC_BE: best effort 104 * @IEEE80211_AC_BK: background 105 */ 106enum ieee80211_ac_numbers { 107 IEEE80211_AC_VO = 0, 108 IEEE80211_AC_VI = 1, 109 IEEE80211_AC_BE = 2, 110 IEEE80211_AC_BK = 3, 111}; 112 113/** 114 * struct ieee80211_tx_queue_params - transmit queue configuration 115 * 116 * The information provided in this structure is required for QoS 117 * transmit queue configuration. Cf. IEEE 802.11 7.3.2.29. 118 * 119 * @aifs: arbitration interframe space [0..255] 120 * @cw_min: minimum contention window [a value of the form 121 * 2^n-1 in the range 1..32767] 122 * @cw_max: maximum contention window [like @cw_min] 123 * @txop: maximum burst time in units of 32 usecs, 0 meaning disabled 124 * @uapsd: is U-APSD mode enabled for the queue 125 */ 126struct ieee80211_tx_queue_params { 127 u16 txop; 128 u16 cw_min; 129 u16 cw_max; 130 u8 aifs; 131 bool uapsd; 132}; 133 134struct ieee80211_low_level_stats { 135 unsigned int dot11ACKFailureCount; 136 unsigned int dot11RTSFailureCount; 137 unsigned int dot11FCSErrorCount; 138 unsigned int dot11RTSSuccessCount; 139}; 140 141/** 142 * enum ieee80211_bss_change - BSS change notification flags 143 * 144 * These flags are used with the bss_info_changed() callback 145 * to indicate which BSS parameter changed. 146 * 147 * @BSS_CHANGED_ASSOC: association status changed (associated/disassociated), 148 * also implies a change in the AID. 149 * @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed 150 * @BSS_CHANGED_ERP_PREAMBLE: preamble changed 151 * @BSS_CHANGED_ERP_SLOT: slot timing changed 152 * @BSS_CHANGED_HT: 802.11n parameters changed 153 * @BSS_CHANGED_BASIC_RATES: Basic rateset changed 154 * @BSS_CHANGED_BEACON_INT: Beacon interval changed 155 * @BSS_CHANGED_BSSID: BSSID changed, for whatever 156 * reason (IBSS and managed mode) 157 * @BSS_CHANGED_BEACON: Beacon data changed, retrieve 158 * new beacon (beaconing modes) 159 * @BSS_CHANGED_BEACON_ENABLED: Beaconing should be 160 * enabled/disabled (beaconing modes) 161 * @BSS_CHANGED_CQM: Connection quality monitor config changed 162 * @BSS_CHANGED_IBSS: IBSS join status changed 163 * @BSS_CHANGED_ARP_FILTER: Hardware ARP filter address list or state changed. 164 * @BSS_CHANGED_QOS: QoS for this association was enabled/disabled. Note 165 * that it is only ever disabled for station mode. 166 * @BSS_CHANGED_IDLE: Idle changed for this BSS/interface. 167 */ 168enum ieee80211_bss_change { 169 BSS_CHANGED_ASSOC = 1<<0, 170 BSS_CHANGED_ERP_CTS_PROT = 1<<1, 171 BSS_CHANGED_ERP_PREAMBLE = 1<<2, 172 BSS_CHANGED_ERP_SLOT = 1<<3, 173 BSS_CHANGED_HT = 1<<4, 174 BSS_CHANGED_BASIC_RATES = 1<<5, 175 BSS_CHANGED_BEACON_INT = 1<<6, 176 BSS_CHANGED_BSSID = 1<<7, 177 BSS_CHANGED_BEACON = 1<<8, 178 BSS_CHANGED_BEACON_ENABLED = 1<<9, 179 BSS_CHANGED_CQM = 1<<10, 180 BSS_CHANGED_IBSS = 1<<11, 181 BSS_CHANGED_ARP_FILTER = 1<<12, 182 BSS_CHANGED_QOS = 1<<13, 183 BSS_CHANGED_IDLE = 1<<14, 184 185 /* when adding here, make sure to change ieee80211_reconfig */ 186}; 187 188/* 189 * The maximum number of IPv4 addresses listed for ARP filtering. If the number 190 * of addresses for an interface increase beyond this value, hardware ARP 191 * filtering will be disabled. 192 */ 193#define IEEE80211_BSS_ARP_ADDR_LIST_LEN 4 194 195/** 196 * struct ieee80211_bss_conf - holds the BSS's changing parameters 197 * 198 * This structure keeps information about a BSS (and an association 199 * to that BSS) that can change during the lifetime of the BSS. 200 * 201 * @assoc: association status 202 * @ibss_joined: indicates whether this station is part of an IBSS 203 * or not 204 * @aid: association ID number, valid only when @assoc is true 205 * @use_cts_prot: use CTS protection 206 * @use_short_preamble: use 802.11b short preamble; 207 * if the hardware cannot handle this it must set the 208 * IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE hardware flag 209 * @use_short_slot: use short slot time (only relevant for ERP); 210 * if the hardware cannot handle this it must set the 211 * IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE hardware flag 212 * @dtim_period: num of beacons before the next DTIM, for beaconing, 213 * valid in station mode only while @assoc is true and if also 214 * requested by %IEEE80211_HW_NEED_DTIM_PERIOD (cf. also hw conf 215 * @ps_dtim_period) 216 * @timestamp: beacon timestamp 217 * @beacon_int: beacon interval 218 * @assoc_capability: capabilities taken from assoc resp 219 * @basic_rates: bitmap of basic rates, each bit stands for an 220 * index into the rate table configured by the driver in 221 * the current band. 222 * @mcast_rate: per-band multicast rate index + 1 (0: disabled) 223 * @bssid: The BSSID for this BSS 224 * @enable_beacon: whether beaconing should be enabled or not 225 * @channel_type: Channel type for this BSS -- the hardware might be 226 * configured for HT40+ while this BSS only uses no-HT, for 227 * example. 228 * @ht_operation_mode: HT operation mode (like in &struct ieee80211_ht_info). 229 * This field is only valid when the channel type is one of the HT types. 230 * @cqm_rssi_thold: Connection quality monitor RSSI threshold, a zero value 231 * implies disabled 232 * @cqm_rssi_hyst: Connection quality monitor RSSI hysteresis 233 * @arp_addr_list: List of IPv4 addresses for hardware ARP filtering. The 234 * may filter ARP queries targeted for other addresses than listed here. 235 * The driver must allow ARP queries targeted for all address listed here 236 * to pass through. An empty list implies no ARP queries need to pass. 237 * @arp_addr_cnt: Number of addresses currently on the list. 238 * @arp_filter_enabled: Enable ARP filtering - if enabled, the hardware may 239 * filter ARP queries based on the @arp_addr_list, if disabled, the 240 * hardware must not perform any ARP filtering. Note, that the filter will 241 * be enabled also in promiscuous mode. 242 * @qos: This is a QoS-enabled BSS. 243 * @idle: This interface is idle. There's also a global idle flag in the 244 * hardware config which may be more appropriate depending on what 245 * your driver/device needs to do. 246 */ 247struct ieee80211_bss_conf { 248 const u8 *bssid; 249 /* association related data */ 250 bool assoc, ibss_joined; 251 u16 aid; 252 /* erp related data */ 253 bool use_cts_prot; 254 bool use_short_preamble; 255 bool use_short_slot; 256 bool enable_beacon; 257 u8 dtim_period; 258 u16 beacon_int; 259 u16 assoc_capability; 260 u64 timestamp; 261 u32 basic_rates; 262 int mcast_rate[IEEE80211_NUM_BANDS]; 263 u16 ht_operation_mode; 264 s32 cqm_rssi_thold; 265 u32 cqm_rssi_hyst; 266 enum nl80211_channel_type channel_type; 267 __be32 arp_addr_list[IEEE80211_BSS_ARP_ADDR_LIST_LEN]; 268 u8 arp_addr_cnt; 269 bool arp_filter_enabled; 270 bool qos; 271 bool idle; 272}; 273 274/** 275 * enum mac80211_tx_control_flags - flags to describe transmission information/status 276 * 277 * These flags are used with the @flags member of &ieee80211_tx_info. 278 * 279 * @IEEE80211_TX_CTL_REQ_TX_STATUS: require TX status callback for this frame. 280 * @IEEE80211_TX_CTL_ASSIGN_SEQ: The driver has to assign a sequence 281 * number to this frame, taking care of not overwriting the fragment 282 * number and increasing the sequence number only when the 283 * IEEE80211_TX_CTL_FIRST_FRAGMENT flag is set. mac80211 will properly 284 * assign sequence numbers to QoS-data frames but cannot do so correctly 285 * for non-QoS-data and management frames because beacons need them from 286 * that counter as well and mac80211 cannot guarantee proper sequencing. 287 * If this flag is set, the driver should instruct the hardware to 288 * assign a sequence number to the frame or assign one itself. Cf. IEEE 289 * 802.11-2007 7.1.3.4.1 paragraph 3. This flag will always be set for 290 * beacons and always be clear for frames without a sequence number field. 291 * @IEEE80211_TX_CTL_NO_ACK: tell the low level not to wait for an ack 292 * @IEEE80211_TX_CTL_CLEAR_PS_FILT: clear powersave filter for destination 293 * station 294 * @IEEE80211_TX_CTL_FIRST_FRAGMENT: this is a first fragment of the frame 295 * @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon 296 * @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU 297 * @IEEE80211_TX_CTL_INJECTED: Frame was injected, internal to mac80211. 298 * @IEEE80211_TX_STAT_TX_FILTERED: The frame was not transmitted 299 * because the destination STA was in powersave mode. Note that to 300 * avoid race conditions, the filter must be set by the hardware or 301 * firmware upon receiving a frame that indicates that the station 302 * went to sleep (must be done on device to filter frames already on 303 * the queue) and may only be unset after mac80211 gives the OK for 304 * that by setting the IEEE80211_TX_CTL_CLEAR_PS_FILT (see above), 305 * since only then is it guaranteed that no more frames are in the 306 * hardware queue. 307 * @IEEE80211_TX_STAT_ACK: Frame was acknowledged 308 * @IEEE80211_TX_STAT_AMPDU: The frame was aggregated, so status 309 * is for the whole aggregation. 310 * @IEEE80211_TX_STAT_AMPDU_NO_BACK: no block ack was returned, 311 * so consider using block ack request (BAR). 312 * @IEEE80211_TX_CTL_RATE_CTRL_PROBE: internal to mac80211, can be 313 * set by rate control algorithms to indicate probe rate, will 314 * be cleared for fragmented frames (except on the last fragment) 315 * @IEEE80211_TX_INTFL_NEED_TXPROCESSING: completely internal to mac80211, 316 * used to indicate that a pending frame requires TX processing before 317 * it can be sent out. 318 * @IEEE80211_TX_INTFL_RETRIED: completely internal to mac80211, 319 * used to indicate that a frame was already retried due to PS 320 * @IEEE80211_TX_INTFL_DONT_ENCRYPT: completely internal to mac80211, 321 * used to indicate frame should not be encrypted 322 * @IEEE80211_TX_CTL_PSPOLL_RESPONSE: (internal?) 323 * This frame is a response to a PS-poll frame and should be sent 324 * although the station is in powersave mode. 325 * @IEEE80211_TX_CTL_MORE_FRAMES: More frames will be passed to the 326 * transmit function after the current frame, this can be used 327 * by drivers to kick the DMA queue only if unset or when the 328 * queue gets full. 329 * @IEEE80211_TX_INTFL_RETRANSMISSION: This frame is being retransmitted 330 * after TX status because the destination was asleep, it must not 331 * be modified again (no seqno assignment, crypto, etc.) 332 * @IEEE80211_TX_INTFL_HAS_RADIOTAP: This frame was injected and still 333 * has a radiotap header at skb->data. 334 * @IEEE80211_TX_INTFL_NL80211_FRAME_TX: Frame was requested through nl80211 335 * MLME command (internal to mac80211 to figure out whether to send TX 336 * status to user space) 337 * @IEEE80211_TX_CTL_LDPC: tells the driver to use LDPC for this frame 338 * @IEEE80211_TX_CTL_STBC: Enables Space-Time Block Coding (STBC) for this 339 * frame and selects the maximum number of streams that it can use. 340 * @IEEE80211_TX_CTL_TX_OFFCHAN: Marks this packet to be transmitted on 341 * the off-channel channel when a remain-on-channel offload is done 342 * in hardware -- normal packets still flow and are expected to be 343 * handled properly by the device. 344 * @IEEE80211_TX_INTFL_TKIP_MIC_FAILURE: Marks this packet to be used for TKIP 345 * testing. It will be sent out with incorrect Michael MIC key to allow 346 * TKIP countermeasures to be tested. 347 * 348 * Note: If you have to add new flags to the enumeration, then don't 349 * forget to update %IEEE80211_TX_TEMPORARY_FLAGS when necessary. 350 */ 351enum mac80211_tx_control_flags { 352 IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0), 353 IEEE80211_TX_CTL_ASSIGN_SEQ = BIT(1), 354 IEEE80211_TX_CTL_NO_ACK = BIT(2), 355 IEEE80211_TX_CTL_CLEAR_PS_FILT = BIT(3), 356 IEEE80211_TX_CTL_FIRST_FRAGMENT = BIT(4), 357 IEEE80211_TX_CTL_SEND_AFTER_DTIM = BIT(5), 358 IEEE80211_TX_CTL_AMPDU = BIT(6), 359 IEEE80211_TX_CTL_INJECTED = BIT(7), 360 IEEE80211_TX_STAT_TX_FILTERED = BIT(8), 361 IEEE80211_TX_STAT_ACK = BIT(9), 362 IEEE80211_TX_STAT_AMPDU = BIT(10), 363 IEEE80211_TX_STAT_AMPDU_NO_BACK = BIT(11), 364 IEEE80211_TX_CTL_RATE_CTRL_PROBE = BIT(12), 365 IEEE80211_TX_INTFL_NEED_TXPROCESSING = BIT(14), 366 IEEE80211_TX_INTFL_RETRIED = BIT(15), 367 IEEE80211_TX_INTFL_DONT_ENCRYPT = BIT(16), 368 IEEE80211_TX_CTL_PSPOLL_RESPONSE = BIT(17), 369 IEEE80211_TX_CTL_MORE_FRAMES = BIT(18), 370 IEEE80211_TX_INTFL_RETRANSMISSION = BIT(19), 371 IEEE80211_TX_INTFL_HAS_RADIOTAP = BIT(20), 372 IEEE80211_TX_INTFL_NL80211_FRAME_TX = BIT(21), 373 IEEE80211_TX_CTL_LDPC = BIT(22), 374 IEEE80211_TX_CTL_STBC = BIT(23) | BIT(24), 375 IEEE80211_TX_CTL_TX_OFFCHAN = BIT(25), 376 IEEE80211_TX_INTFL_TKIP_MIC_FAILURE = BIT(26), 377}; 378 379#define IEEE80211_TX_CTL_STBC_SHIFT 23 380 381/* 382 * This definition is used as a mask to clear all temporary flags, which are 383 * set by the tx handlers for each transmission attempt by the mac80211 stack. 384 */ 385#define IEEE80211_TX_TEMPORARY_FLAGS (IEEE80211_TX_CTL_NO_ACK | \ 386 IEEE80211_TX_CTL_CLEAR_PS_FILT | IEEE80211_TX_CTL_FIRST_FRAGMENT | \ 387 IEEE80211_TX_CTL_SEND_AFTER_DTIM | IEEE80211_TX_CTL_AMPDU | \ 388 IEEE80211_TX_STAT_TX_FILTERED | IEEE80211_TX_STAT_ACK | \ 389 IEEE80211_TX_STAT_AMPDU | IEEE80211_TX_STAT_AMPDU_NO_BACK | \ 390 IEEE80211_TX_CTL_RATE_CTRL_PROBE | IEEE80211_TX_CTL_PSPOLL_RESPONSE | \ 391 IEEE80211_TX_CTL_MORE_FRAMES | IEEE80211_TX_CTL_LDPC | \ 392 IEEE80211_TX_CTL_STBC) 393 394/** 395 * enum mac80211_rate_control_flags - per-rate flags set by the 396 * Rate Control algorithm. 397 * 398 * These flags are set by the Rate control algorithm for each rate during tx, 399 * in the @flags member of struct ieee80211_tx_rate. 400 * 401 * @IEEE80211_TX_RC_USE_RTS_CTS: Use RTS/CTS exchange for this rate. 402 * @IEEE80211_TX_RC_USE_CTS_PROTECT: CTS-to-self protection is required. 403 * This is set if the current BSS requires ERP protection. 404 * @IEEE80211_TX_RC_USE_SHORT_PREAMBLE: Use short preamble. 405 * @IEEE80211_TX_RC_MCS: HT rate. 406 * @IEEE80211_TX_RC_GREEN_FIELD: Indicates whether this rate should be used in 407 * Greenfield mode. 408 * @IEEE80211_TX_RC_40_MHZ_WIDTH: Indicates if the Channel Width should be 40 MHz. 409 * @IEEE80211_TX_RC_DUP_DATA: The frame should be transmitted on both of the 410 * adjacent 20 MHz channels, if the current channel type is 411 * NL80211_CHAN_HT40MINUS or NL80211_CHAN_HT40PLUS. 412 * @IEEE80211_TX_RC_SHORT_GI: Short Guard interval should be used for this rate. 413 */ 414enum mac80211_rate_control_flags { 415 IEEE80211_TX_RC_USE_RTS_CTS = BIT(0), 416 IEEE80211_TX_RC_USE_CTS_PROTECT = BIT(1), 417 IEEE80211_TX_RC_USE_SHORT_PREAMBLE = BIT(2), 418 419 /* rate index is an MCS rate number instead of an index */ 420 IEEE80211_TX_RC_MCS = BIT(3), 421 IEEE80211_TX_RC_GREEN_FIELD = BIT(4), 422 IEEE80211_TX_RC_40_MHZ_WIDTH = BIT(5), 423 IEEE80211_TX_RC_DUP_DATA = BIT(6), 424 IEEE80211_TX_RC_SHORT_GI = BIT(7), 425}; 426 427 428/* there are 40 bytes if you don't need the rateset to be kept */ 429#define IEEE80211_TX_INFO_DRIVER_DATA_SIZE 40 430 431/* if you do need the rateset, then you have less space */ 432#define IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE 24 433 434/* maximum number of rate stages */ 435#define IEEE80211_TX_MAX_RATES 5 436 437/** 438 * struct ieee80211_tx_rate - rate selection/status 439 * 440 * @idx: rate index to attempt to send with 441 * @flags: rate control flags (&enum mac80211_rate_control_flags) 442 * @count: number of tries in this rate before going to the next rate 443 * 444 * A value of -1 for @idx indicates an invalid rate and, if used 445 * in an array of retry rates, that no more rates should be tried. 446 * 447 * When used for transmit status reporting, the driver should 448 * always report the rate along with the flags it used. 449 * 450 * &struct ieee80211_tx_info contains an array of these structs 451 * in the control information, and it will be filled by the rate 452 * control algorithm according to what should be sent. For example, 453 * if this array contains, in the format { <idx>, <count> } the 454 * information 455 * { 3, 2 }, { 2, 2 }, { 1, 4 }, { -1, 0 }, { -1, 0 } 456 * then this means that the frame should be transmitted 457 * up to twice at rate 3, up to twice at rate 2, and up to four 458 * times at rate 1 if it doesn't get acknowledged. Say it gets 459 * acknowledged by the peer after the fifth attempt, the status 460 * information should then contain 461 * { 3, 2 }, { 2, 2 }, { 1, 1 }, { -1, 0 } ... 462 * since it was transmitted twice at rate 3, twice at rate 2 463 * and once at rate 1 after which we received an acknowledgement. 464 */ 465struct ieee80211_tx_rate { 466 s8 idx; 467 u8 count; 468 u8 flags; 469} __packed; 470 471/** 472 * struct ieee80211_tx_info - skb transmit information 473 * 474 * This structure is placed in skb->cb for three uses: 475 * (1) mac80211 TX control - mac80211 tells the driver what to do 476 * (2) driver internal use (if applicable) 477 * (3) TX status information - driver tells mac80211 what happened 478 * 479 * The TX control's sta pointer is only valid during the ->tx call, 480 * it may be NULL. 481 * 482 * @flags: transmit info flags, defined above 483 * @band: the band to transmit on (use for checking for races) 484 * @antenna_sel_tx: antenna to use, 0 for automatic diversity 485 * @pad: padding, ignore 486 * @control: union for control data 487 * @status: union for status data 488 * @driver_data: array of driver_data pointers 489 * @ampdu_ack_len: number of acked aggregated frames. 490 * relevant only if IEEE80211_TX_STAT_AMPDU was set. 491 * @ampdu_len: number of aggregated frames. 492 * relevant only if IEEE80211_TX_STAT_AMPDU was set. 493 * @ack_signal: signal strength of the ACK frame 494 */ 495struct ieee80211_tx_info { 496 /* common information */ 497 u32 flags; 498 u8 band; 499 500 u8 antenna_sel_tx; 501 502 /* 2 byte hole */ 503 u8 pad[2]; 504 505 union { 506 struct { 507 union { 508 /* rate control */ 509 struct { 510 struct ieee80211_tx_rate rates[ 511 IEEE80211_TX_MAX_RATES]; 512 s8 rts_cts_rate_idx; 513 }; 514 /* only needed before rate control */ 515 unsigned long jiffies; 516 }; 517 /* NB: vif can be NULL for injected frames */ 518 struct ieee80211_vif *vif; 519 struct ieee80211_key_conf *hw_key; 520 struct ieee80211_sta *sta; 521 } control; 522 struct { 523 struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES]; 524 u8 ampdu_ack_len; 525 int ack_signal; 526 u8 ampdu_len; 527 /* 15 bytes free */ 528 } status; 529 struct { 530 struct ieee80211_tx_rate driver_rates[ 531 IEEE80211_TX_MAX_RATES]; 532 void *rate_driver_data[ 533 IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE / sizeof(void *)]; 534 }; 535 void *driver_data[ 536 IEEE80211_TX_INFO_DRIVER_DATA_SIZE / sizeof(void *)]; 537 }; 538}; 539 540/** 541 * struct ieee80211_sched_scan_ies - scheduled scan IEs 542 * 543 * This structure is used to pass the appropriate IEs to be used in scheduled 544 * scans for all bands. It contains both the IEs passed from the userspace 545 * and the ones generated by mac80211. 546 * 547 * @ie: array with the IEs for each supported band 548 * @len: array with the total length of the IEs for each band 549 */ 550struct ieee80211_sched_scan_ies { 551 u8 *ie[IEEE80211_NUM_BANDS]; 552 size_t len[IEEE80211_NUM_BANDS]; 553}; 554 555static inline struct ieee80211_tx_info *IEEE80211_SKB_CB(struct sk_buff *skb) 556{ 557 return (struct ieee80211_tx_info *)skb->cb; 558} 559 560static inline struct ieee80211_rx_status *IEEE80211_SKB_RXCB(struct sk_buff *skb) 561{ 562 return (struct ieee80211_rx_status *)skb->cb; 563} 564 565/** 566 * ieee80211_tx_info_clear_status - clear TX status 567 * 568 * @info: The &struct ieee80211_tx_info to be cleared. 569 * 570 * When the driver passes an skb back to mac80211, it must report 571 * a number of things in TX status. This function clears everything 572 * in the TX status but the rate control information (it does clear 573 * the count since you need to fill that in anyway). 574 * 575 * NOTE: You can only use this function if you do NOT use 576 * info->driver_data! Use info->rate_driver_data 577 * instead if you need only the less space that allows. 578 */ 579static inline void 580ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info) 581{ 582 int i; 583 584 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 585 offsetof(struct ieee80211_tx_info, control.rates)); 586 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 587 offsetof(struct ieee80211_tx_info, driver_rates)); 588 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8); 589 /* clear the rate counts */ 590 for (i = 0; i < IEEE80211_TX_MAX_RATES; i++) 591 info->status.rates[i].count = 0; 592 593 BUILD_BUG_ON( 594 offsetof(struct ieee80211_tx_info, status.ampdu_ack_len) != 23); 595 memset(&info->status.ampdu_ack_len, 0, 596 sizeof(struct ieee80211_tx_info) - 597 offsetof(struct ieee80211_tx_info, status.ampdu_ack_len)); 598} 599 600 601/** 602 * enum mac80211_rx_flags - receive flags 603 * 604 * These flags are used with the @flag member of &struct ieee80211_rx_status. 605 * @RX_FLAG_MMIC_ERROR: Michael MIC error was reported on this frame. 606 * Use together with %RX_FLAG_MMIC_STRIPPED. 607 * @RX_FLAG_DECRYPTED: This frame was decrypted in hardware. 608 * @RX_FLAG_MMIC_STRIPPED: the Michael MIC is stripped off this frame, 609 * verification has been done by the hardware. 610 * @RX_FLAG_IV_STRIPPED: The IV/ICV are stripped from this frame. 611 * If this flag is set, the stack cannot do any replay detection 612 * hence the driver or hardware will have to do that. 613 * @RX_FLAG_FAILED_FCS_CRC: Set this flag if the FCS check failed on 614 * the frame. 615 * @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on 616 * the frame. 617 * @RX_FLAG_MACTIME_MPDU: The timestamp passed in the RX status (@mactime 618 * field) is valid and contains the time the first symbol of the MPDU 619 * was received. This is useful in monitor mode and for proper IBSS 620 * merging. 621 * @RX_FLAG_SHORTPRE: Short preamble was used for this frame 622 * @RX_FLAG_HT: HT MCS was used and rate_idx is MCS index 623 * @RX_FLAG_40MHZ: HT40 (40 MHz) was used 624 * @RX_FLAG_SHORT_GI: Short guard interval was used 625 */ 626enum mac80211_rx_flags { 627 RX_FLAG_MMIC_ERROR = 1<<0, 628 RX_FLAG_DECRYPTED = 1<<1, 629 RX_FLAG_MMIC_STRIPPED = 1<<3, 630 RX_FLAG_IV_STRIPPED = 1<<4, 631 RX_FLAG_FAILED_FCS_CRC = 1<<5, 632 RX_FLAG_FAILED_PLCP_CRC = 1<<6, 633 RX_FLAG_MACTIME_MPDU = 1<<7, 634 RX_FLAG_SHORTPRE = 1<<8, 635 RX_FLAG_HT = 1<<9, 636 RX_FLAG_40MHZ = 1<<10, 637 RX_FLAG_SHORT_GI = 1<<11, 638}; 639 640/** 641 * struct ieee80211_rx_status - receive status 642 * 643 * The low-level driver should provide this information (the subset 644 * supported by hardware) to the 802.11 code with each received 645 * frame, in the skb's control buffer (cb). 646 * 647 * @mactime: value in microseconds of the 64-bit Time Synchronization Function 648 * (TSF) timer when the first data symbol (MPDU) arrived at the hardware. 649 * @band: the active band when this frame was received 650 * @freq: frequency the radio was tuned to when receiving this frame, in MHz 651 * @signal: signal strength when receiving this frame, either in dBm, in dB or 652 * unspecified depending on the hardware capabilities flags 653 * @IEEE80211_HW_SIGNAL_* 654 * @antenna: antenna used 655 * @rate_idx: index of data rate into band's supported rates or MCS index if 656 * HT rates are use (RX_FLAG_HT) 657 * @flag: %RX_FLAG_* 658 * @rx_flags: internal RX flags for mac80211 659 */ 660struct ieee80211_rx_status { 661 u64 mactime; 662 enum ieee80211_band band; 663 int freq; 664 int signal; 665 int antenna; 666 int rate_idx; 667 int flag; 668 unsigned int rx_flags; 669}; 670 671/** 672 * enum ieee80211_conf_flags - configuration flags 673 * 674 * Flags to define PHY configuration options 675 * 676 * @IEEE80211_CONF_MONITOR: there's a monitor interface present -- use this 677 * to determine for example whether to calculate timestamps for packets 678 * or not, do not use instead of filter flags! 679 * @IEEE80211_CONF_PS: Enable 802.11 power save mode (managed mode only). 680 * This is the power save mode defined by IEEE 802.11-2007 section 11.2, 681 * meaning that the hardware still wakes up for beacons, is able to 682 * transmit frames and receive the possible acknowledgment frames. 683 * Not to be confused with hardware specific wakeup/sleep states, 684 * driver is responsible for that. See the section "Powersave support" 685 * for more. 686 * @IEEE80211_CONF_IDLE: The device is running, but idle; if the flag is set 687 * the driver should be prepared to handle configuration requests but 688 * may turn the device off as much as possible. Typically, this flag will 689 * be set when an interface is set UP but not associated or scanning, but 690 * it can also be unset in that case when monitor interfaces are active. 691 * @IEEE80211_CONF_OFFCHANNEL: The device is currently not on its main 692 * operating channel. 693 */ 694enum ieee80211_conf_flags { 695 IEEE80211_CONF_MONITOR = (1<<0), 696 IEEE80211_CONF_PS = (1<<1), 697 IEEE80211_CONF_IDLE = (1<<2), 698 IEEE80211_CONF_OFFCHANNEL = (1<<3), 699}; 700 701 702/** 703 * enum ieee80211_conf_changed - denotes which configuration changed 704 * 705 * @IEEE80211_CONF_CHANGE_LISTEN_INTERVAL: the listen interval changed 706 * @IEEE80211_CONF_CHANGE_MONITOR: the monitor flag changed 707 * @IEEE80211_CONF_CHANGE_PS: the PS flag or dynamic PS timeout changed 708 * @IEEE80211_CONF_CHANGE_POWER: the TX power changed 709 * @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed 710 * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed 711 * @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed 712 * @IEEE80211_CONF_CHANGE_SMPS: Spatial multiplexing powersave mode changed 713 */ 714enum ieee80211_conf_changed { 715 IEEE80211_CONF_CHANGE_SMPS = BIT(1), 716 IEEE80211_CONF_CHANGE_LISTEN_INTERVAL = BIT(2), 717 IEEE80211_CONF_CHANGE_MONITOR = BIT(3), 718 IEEE80211_CONF_CHANGE_PS = BIT(4), 719 IEEE80211_CONF_CHANGE_POWER = BIT(5), 720 IEEE80211_CONF_CHANGE_CHANNEL = BIT(6), 721 IEEE80211_CONF_CHANGE_RETRY_LIMITS = BIT(7), 722 IEEE80211_CONF_CHANGE_IDLE = BIT(8), 723}; 724 725/** 726 * enum ieee80211_smps_mode - spatial multiplexing power save mode 727 * 728 * @IEEE80211_SMPS_AUTOMATIC: automatic 729 * @IEEE80211_SMPS_OFF: off 730 * @IEEE80211_SMPS_STATIC: static 731 * @IEEE80211_SMPS_DYNAMIC: dynamic 732 * @IEEE80211_SMPS_NUM_MODES: internal, don't use 733 */ 734enum ieee80211_smps_mode { 735 IEEE80211_SMPS_AUTOMATIC, 736 IEEE80211_SMPS_OFF, 737 IEEE80211_SMPS_STATIC, 738 IEEE80211_SMPS_DYNAMIC, 739 740 /* keep last */ 741 IEEE80211_SMPS_NUM_MODES, 742}; 743 744/** 745 * struct ieee80211_conf - configuration of the device 746 * 747 * This struct indicates how the driver shall configure the hardware. 748 * 749 * @flags: configuration flags defined above 750 * 751 * @listen_interval: listen interval in units of beacon interval 752 * @max_sleep_period: the maximum number of beacon intervals to sleep for 753 * before checking the beacon for a TIM bit (managed mode only); this 754 * value will be only achievable between DTIM frames, the hardware 755 * needs to check for the multicast traffic bit in DTIM beacons. 756 * This variable is valid only when the CONF_PS flag is set. 757 * @ps_dtim_period: The DTIM period of the AP we're connected to, for use 758 * in power saving. Power saving will not be enabled until a beacon 759 * has been received and the DTIM period is known. 760 * @dynamic_ps_timeout: The dynamic powersave timeout (in ms), see the 761 * powersave documentation below. This variable is valid only when 762 * the CONF_PS flag is set. 763 * 764 * @power_level: requested transmit power (in dBm) 765 * 766 * @channel: the channel to tune to 767 * @channel_type: the channel (HT) type 768 * 769 * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame 770 * (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11, 771 * but actually means the number of transmissions not the number of retries 772 * @short_frame_max_tx_count: Maximum number of transmissions for a "short" 773 * frame, called "dot11ShortRetryLimit" in 802.11, but actually means the 774 * number of transmissions not the number of retries 775 * 776 * @smps_mode: spatial multiplexing powersave mode; note that 777 * %IEEE80211_SMPS_STATIC is used when the device is not 778 * configured for an HT channel 779 */ 780struct ieee80211_conf { 781 u32 flags; 782 int power_level, dynamic_ps_timeout; 783 int max_sleep_period; 784 785 u16 listen_interval; 786 u8 ps_dtim_period; 787 788 u8 long_frame_max_tx_count, short_frame_max_tx_count; 789 790 struct ieee80211_channel *channel; 791 enum nl80211_channel_type channel_type; 792 enum ieee80211_smps_mode smps_mode; 793}; 794 795/** 796 * struct ieee80211_channel_switch - holds the channel switch data 797 * 798 * The information provided in this structure is required for channel switch 799 * operation. 800 * 801 * @timestamp: value in microseconds of the 64-bit Time Synchronization 802 * Function (TSF) timer when the frame containing the channel switch 803 * announcement was received. This is simply the rx.mactime parameter 804 * the driver passed into mac80211. 805 * @block_tx: Indicates whether transmission must be blocked before the 806 * scheduled channel switch, as indicated by the AP. 807 * @channel: the new channel to switch to 808 * @count: the number of TBTT's until the channel switch event 809 */ 810struct ieee80211_channel_switch { 811 u64 timestamp; 812 bool block_tx; 813 struct ieee80211_channel *channel; 814 u8 count; 815}; 816 817/** 818 * struct ieee80211_vif - per-interface data 819 * 820 * Data in this structure is continually present for driver 821 * use during the life of a virtual interface. 822 * 823 * @type: type of this virtual interface 824 * @bss_conf: BSS configuration for this interface, either our own 825 * or the BSS we're associated to 826 * @addr: address of this interface 827 * @p2p: indicates whether this AP or STA interface is a p2p 828 * interface, i.e. a GO or p2p-sta respectively 829 * @drv_priv: data area for driver use, will always be aligned to 830 * sizeof(void *). 831 */ 832struct ieee80211_vif { 833 enum nl80211_iftype type; 834 struct ieee80211_bss_conf bss_conf; 835 u8 addr[ETH_ALEN]; 836 bool p2p; 837 /* must be last */ 838 u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *)))); 839}; 840 841static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif) 842{ 843#ifdef CONFIG_MAC80211_MESH 844 return vif->type == NL80211_IFTYPE_MESH_POINT; 845#endif 846 return false; 847} 848 849/** 850 * enum ieee80211_key_flags - key flags 851 * 852 * These flags are used for communication about keys between the driver 853 * and mac80211, with the @flags parameter of &struct ieee80211_key_conf. 854 * 855 * @IEEE80211_KEY_FLAG_WMM_STA: Set by mac80211, this flag indicates 856 * that the STA this key will be used with could be using QoS. 857 * @IEEE80211_KEY_FLAG_GENERATE_IV: This flag should be set by the 858 * driver to indicate that it requires IV generation for this 859 * particular key. 860 * @IEEE80211_KEY_FLAG_GENERATE_MMIC: This flag should be set by 861 * the driver for a TKIP key if it requires Michael MIC 862 * generation in software. 863 * @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates 864 * that the key is pairwise rather then a shared key. 865 * @IEEE80211_KEY_FLAG_SW_MGMT: This flag should be set by the driver for a 866 * CCMP key if it requires CCMP encryption of management frames (MFP) to 867 * be done in software. 868 */ 869enum ieee80211_key_flags { 870 IEEE80211_KEY_FLAG_WMM_STA = 1<<0, 871 IEEE80211_KEY_FLAG_GENERATE_IV = 1<<1, 872 IEEE80211_KEY_FLAG_GENERATE_MMIC= 1<<2, 873 IEEE80211_KEY_FLAG_PAIRWISE = 1<<3, 874 IEEE80211_KEY_FLAG_SW_MGMT = 1<<4, 875}; 876 877/** 878 * struct ieee80211_key_conf - key information 879 * 880 * This key information is given by mac80211 to the driver by 881 * the set_key() callback in &struct ieee80211_ops. 882 * 883 * @hw_key_idx: To be set by the driver, this is the key index the driver 884 * wants to be given when a frame is transmitted and needs to be 885 * encrypted in hardware. 886 * @cipher: The key's cipher suite selector. 887 * @flags: key flags, see &enum ieee80211_key_flags. 888 * @keyidx: the key index (0-3) 889 * @keylen: key material length 890 * @key: key material. For ALG_TKIP the key is encoded as a 256-bit (32 byte) 891 * data block: 892 * - Temporal Encryption Key (128 bits) 893 * - Temporal Authenticator Tx MIC Key (64 bits) 894 * - Temporal Authenticator Rx MIC Key (64 bits) 895 * @icv_len: The ICV length for this key type 896 * @iv_len: The IV length for this key type 897 */ 898struct ieee80211_key_conf { 899 u32 cipher; 900 u8 icv_len; 901 u8 iv_len; 902 u8 hw_key_idx; 903 u8 flags; 904 s8 keyidx; 905 u8 keylen; 906 u8 key[0]; 907}; 908 909/** 910 * enum set_key_cmd - key command 911 * 912 * Used with the set_key() callback in &struct ieee80211_ops, this 913 * indicates whether a key is being removed or added. 914 * 915 * @SET_KEY: a key is set 916 * @DISABLE_KEY: a key must be disabled 917 */ 918enum set_key_cmd { 919 SET_KEY, DISABLE_KEY, 920}; 921 922/** 923 * struct ieee80211_sta - station table entry 924 * 925 * A station table entry represents a station we are possibly 926 * communicating with. Since stations are RCU-managed in 927 * mac80211, any ieee80211_sta pointer you get access to must 928 * either be protected by rcu_read_lock() explicitly or implicitly, 929 * or you must take good care to not use such a pointer after a 930 * call to your sta_remove callback that removed it. 931 * 932 * @addr: MAC address 933 * @aid: AID we assigned to the station if we're an AP 934 * @supp_rates: Bitmap of supported rates (per band) 935 * @ht_cap: HT capabilities of this STA; restricted to our own TX capabilities 936 * @wme: indicates whether the STA supports WME. Only valid during AP-mode. 937 * @drv_priv: data area for driver use, will always be aligned to 938 * sizeof(void *), size is determined in hw information. 939 */ 940struct ieee80211_sta { 941 u32 supp_rates[IEEE80211_NUM_BANDS]; 942 u8 addr[ETH_ALEN]; 943 u16 aid; 944 struct ieee80211_sta_ht_cap ht_cap; 945 bool wme; 946 947 /* must be last */ 948 u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *)))); 949}; 950 951/** 952 * enum sta_notify_cmd - sta notify command 953 * 954 * Used with the sta_notify() callback in &struct ieee80211_ops, this 955 * indicates if an associated station made a power state transition. 956 * 957 * @STA_NOTIFY_SLEEP: a station is now sleeping 958 * @STA_NOTIFY_AWAKE: a sleeping station woke up 959 */ 960enum sta_notify_cmd { 961 STA_NOTIFY_SLEEP, STA_NOTIFY_AWAKE, 962}; 963 964/** 965 * enum ieee80211_hw_flags - hardware flags 966 * 967 * These flags are used to indicate hardware capabilities to 968 * the stack. Generally, flags here should have their meaning 969 * done in a way that the simplest hardware doesn't need setting 970 * any particular flags. There are some exceptions to this rule, 971 * however, so you are advised to review these flags carefully. 972 * 973 * @IEEE80211_HW_HAS_RATE_CONTROL: 974 * The hardware or firmware includes rate control, and cannot be 975 * controlled by the stack. As such, no rate control algorithm 976 * should be instantiated, and the TX rate reported to userspace 977 * will be taken from the TX status instead of the rate control 978 * algorithm. 979 * Note that this requires that the driver implement a number of 980 * callbacks so it has the correct information, it needs to have 981 * the @set_rts_threshold callback and must look at the BSS config 982 * @use_cts_prot for G/N protection, @use_short_slot for slot 983 * timing in 2.4 GHz and @use_short_preamble for preambles for 984 * CCK frames. 985 * 986 * @IEEE80211_HW_RX_INCLUDES_FCS: 987 * Indicates that received frames passed to the stack include 988 * the FCS at the end. 989 * 990 * @IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING: 991 * Some wireless LAN chipsets buffer broadcast/multicast frames 992 * for power saving stations in the hardware/firmware and others 993 * rely on the host system for such buffering. This option is used 994 * to configure the IEEE 802.11 upper layer to buffer broadcast and 995 * multicast frames when there are power saving stations so that 996 * the driver can fetch them with ieee80211_get_buffered_bc(). 997 * 998 * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE: 999 * Hardware is not capable of short slot operation on the 2.4 GHz band. 1000 * 1001 * @IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE: 1002 * Hardware is not capable of receiving frames with short preamble on 1003 * the 2.4 GHz band. 1004 * 1005 * @IEEE80211_HW_SIGNAL_UNSPEC: 1006 * Hardware can provide signal values but we don't know its units. We 1007 * expect values between 0 and @max_signal. 1008 * If possible please provide dB or dBm instead. 1009 * 1010 * @IEEE80211_HW_SIGNAL_DBM: 1011 * Hardware gives signal values in dBm, decibel difference from 1012 * one milliwatt. This is the preferred method since it is standardized 1013 * between different devices. @max_signal does not need to be set. 1014 * 1015 * @IEEE80211_HW_SPECTRUM_MGMT: 1016 * Hardware supports spectrum management defined in 802.11h 1017 * Measurement, Channel Switch, Quieting, TPC 1018 * 1019 * @IEEE80211_HW_AMPDU_AGGREGATION: 1020 * Hardware supports 11n A-MPDU aggregation. 1021 * 1022 * @IEEE80211_HW_SUPPORTS_PS: 1023 * Hardware has power save support (i.e. can go to sleep). 1024 * 1025 * @IEEE80211_HW_PS_NULLFUNC_STACK: 1026 * Hardware requires nullfunc frame handling in stack, implies 1027 * stack support for dynamic PS. 1028 * 1029 * @IEEE80211_HW_SUPPORTS_DYNAMIC_PS: 1030 * Hardware has support for dynamic PS. 1031 * 1032 * @IEEE80211_HW_MFP_CAPABLE: 1033 * Hardware supports management frame protection (MFP, IEEE 802.11w). 1034 * 1035 * @IEEE80211_HW_BEACON_FILTER: 1036 * Hardware supports dropping of irrelevant beacon frames to 1037 * avoid waking up cpu. 1038 * 1039 * @IEEE80211_HW_SUPPORTS_STATIC_SMPS: 1040 * Hardware supports static spatial multiplexing powersave, 1041 * ie. can turn off all but one chain even on HT connections 1042 * that should be using more chains. 1043 * 1044 * @IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS: 1045 * Hardware supports dynamic spatial multiplexing powersave, 1046 * ie. can turn off all but one chain and then wake the rest 1047 * up as required after, for example, rts/cts handshake. 1048 * 1049 * @IEEE80211_HW_SUPPORTS_UAPSD: 1050 * Hardware supports Unscheduled Automatic Power Save Delivery 1051 * (U-APSD) in managed mode. The mode is configured with 1052 * conf_tx() operation. 1053 * 1054 * @IEEE80211_HW_REPORTS_TX_ACK_STATUS: 1055 * Hardware can provide ack status reports of Tx frames to 1056 * the stack. 1057 * 1058 * @IEEE80211_HW_CONNECTION_MONITOR: 1059 * The hardware performs its own connection monitoring, including 1060 * periodic keep-alives to the AP and probing the AP on beacon loss. 1061 * When this flag is set, signaling beacon-loss will cause an immediate 1062 * change to disassociated state. 1063 * 1064 * @IEEE80211_HW_SUPPORTS_CQM_RSSI: 1065 * Hardware can do connection quality monitoring - i.e. it can monitor 1066 * connection quality related parameters, such as the RSSI level and 1067 * provide notifications if configured trigger levels are reached. 1068 * 1069 * @IEEE80211_HW_NEED_DTIM_PERIOD: 1070 * This device needs to know the DTIM period for the BSS before 1071 * associating. 1072 * 1073 * @IEEE80211_HW_SUPPORTS_PER_STA_GTK: The device's crypto engine supports 1074 * per-station GTKs as used by IBSS RSN or during fast transition. If 1075 * the device doesn't support per-station GTKs, but can be asked not 1076 * to decrypt group addressed frames, then IBSS RSN support is still 1077 * possible but software crypto will be used. Advertise the wiphy flag 1078 * only in that case. 1079 * 1080 * @IEEE80211_HW_AP_LINK_PS: When operating in AP mode the device 1081 * autonomously manages the PS status of connected stations. When 1082 * this flag is set mac80211 will not trigger PS mode for connected 1083 * stations based on the PM bit of incoming frames. 1084 * Use ieee80211_start_ps()/ieee8021_end_ps() to manually configure 1085 * the PS mode of connected stations. 1086 */ 1087enum ieee80211_hw_flags { 1088 IEEE80211_HW_HAS_RATE_CONTROL = 1<<0, 1089 IEEE80211_HW_RX_INCLUDES_FCS = 1<<1, 1090 IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING = 1<<2, 1091 IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE = 1<<3, 1092 IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE = 1<<4, 1093 IEEE80211_HW_SIGNAL_UNSPEC = 1<<5, 1094 IEEE80211_HW_SIGNAL_DBM = 1<<6, 1095 IEEE80211_HW_NEED_DTIM_PERIOD = 1<<7, 1096 IEEE80211_HW_SPECTRUM_MGMT = 1<<8, 1097 IEEE80211_HW_AMPDU_AGGREGATION = 1<<9, 1098 IEEE80211_HW_SUPPORTS_PS = 1<<10, 1099 IEEE80211_HW_PS_NULLFUNC_STACK = 1<<11, 1100 IEEE80211_HW_SUPPORTS_DYNAMIC_PS = 1<<12, 1101 IEEE80211_HW_MFP_CAPABLE = 1<<13, 1102 IEEE80211_HW_BEACON_FILTER = 1<<14, 1103 IEEE80211_HW_SUPPORTS_STATIC_SMPS = 1<<15, 1104 IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS = 1<<16, 1105 IEEE80211_HW_SUPPORTS_UAPSD = 1<<17, 1106 IEEE80211_HW_REPORTS_TX_ACK_STATUS = 1<<18, 1107 IEEE80211_HW_CONNECTION_MONITOR = 1<<19, 1108 IEEE80211_HW_SUPPORTS_CQM_RSSI = 1<<20, 1109 IEEE80211_HW_SUPPORTS_PER_STA_GTK = 1<<21, 1110 IEEE80211_HW_AP_LINK_PS = 1<<22, 1111}; 1112 1113/** 1114 * struct ieee80211_hw - hardware information and state 1115 * 1116 * This structure contains the configuration and hardware 1117 * information for an 802.11 PHY. 1118 * 1119 * @wiphy: This points to the &struct wiphy allocated for this 1120 * 802.11 PHY. You must fill in the @perm_addr and @dev 1121 * members of this structure using SET_IEEE80211_DEV() 1122 * and SET_IEEE80211_PERM_ADDR(). Additionally, all supported 1123 * bands (with channels, bitrates) are registered here. 1124 * 1125 * @conf: &struct ieee80211_conf, device configuration, don't use. 1126 * 1127 * @priv: pointer to private area that was allocated for driver use 1128 * along with this structure. 1129 * 1130 * @flags: hardware flags, see &enum ieee80211_hw_flags. 1131 * 1132 * @extra_tx_headroom: headroom to reserve in each transmit skb 1133 * for use by the driver (e.g. for transmit headers.) 1134 * 1135 * @channel_change_time: time (in microseconds) it takes to change channels. 1136 * 1137 * @max_signal: Maximum value for signal (rssi) in RX information, used 1138 * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB 1139 * 1140 * @max_listen_interval: max listen interval in units of beacon interval 1141 * that HW supports 1142 * 1143 * @queues: number of available hardware transmit queues for 1144 * data packets. WMM/QoS requires at least four, these 1145 * queues need to have configurable access parameters. 1146 * 1147 * @rate_control_algorithm: rate control algorithm for this hardware. 1148 * If unset (NULL), the default algorithm will be used. Must be 1149 * set before calling ieee80211_register_hw(). 1150 * 1151 * @vif_data_size: size (in bytes) of the drv_priv data area 1152 * within &struct ieee80211_vif. 1153 * @sta_data_size: size (in bytes) of the drv_priv data area 1154 * within &struct ieee80211_sta. 1155 * 1156 * @max_rates: maximum number of alternate rate retry stages the hw 1157 * can handle. 1158 * @max_report_rates: maximum number of alternate rate retry stages 1159 * the hw can report back. 1160 * @max_rate_tries: maximum number of tries for each stage 1161 * 1162 * @napi_weight: weight used for NAPI polling. You must specify an 1163 * appropriate value here if a napi_poll operation is provided 1164 * by your driver. 1165 * 1166 * @max_rx_aggregation_subframes: maximum buffer size (number of 1167 * sub-frames) to be used for A-MPDU block ack receiver 1168 * aggregation. 1169 * This is only relevant if the device has restrictions on the 1170 * number of subframes, if it relies on mac80211 to do reordering 1171 * it shouldn't be set. 1172 * 1173 * @max_tx_aggregation_subframes: maximum number of subframes in an 1174 * aggregate an HT driver will transmit, used by the peer as a 1175 * hint to size its reorder buffer. 1176 */ 1177struct ieee80211_hw { 1178 struct ieee80211_conf conf; 1179 struct wiphy *wiphy; 1180 const char *rate_control_algorithm; 1181 void *priv; 1182 u32 flags; 1183 unsigned int extra_tx_headroom; 1184 int channel_change_time; 1185 int vif_data_size; 1186 int sta_data_size; 1187 int napi_weight; 1188 u16 queues; 1189 u16 max_listen_interval; 1190 s8 max_signal; 1191 u8 max_rates; 1192 u8 max_report_rates; 1193 u8 max_rate_tries; 1194 u8 max_rx_aggregation_subframes; 1195 u8 max_tx_aggregation_subframes; 1196}; 1197 1198/** 1199 * wiphy_to_ieee80211_hw - return a mac80211 driver hw struct from a wiphy 1200 * 1201 * @wiphy: the &struct wiphy which we want to query 1202 * 1203 * mac80211 drivers can use this to get to their respective 1204 * &struct ieee80211_hw. Drivers wishing to get to their own private 1205 * structure can then access it via hw->priv. Note that mac802111 drivers should 1206 * not use wiphy_priv() to try to get their private driver structure as this 1207 * is already used internally by mac80211. 1208 */ 1209struct ieee80211_hw *wiphy_to_ieee80211_hw(struct wiphy *wiphy); 1210 1211/** 1212 * SET_IEEE80211_DEV - set device for 802.11 hardware 1213 * 1214 * @hw: the &struct ieee80211_hw to set the device for 1215 * @dev: the &struct device of this 802.11 device 1216 */ 1217static inline void SET_IEEE80211_DEV(struct ieee80211_hw *hw, struct device *dev) 1218{ 1219 set_wiphy_dev(hw->wiphy, dev); 1220} 1221 1222/** 1223 * SET_IEEE80211_PERM_ADDR - set the permanent MAC address for 802.11 hardware 1224 * 1225 * @hw: the &struct ieee80211_hw to set the MAC address for 1226 * @addr: the address to set 1227 */ 1228static inline void SET_IEEE80211_PERM_ADDR(struct ieee80211_hw *hw, u8 *addr) 1229{ 1230 memcpy(hw->wiphy->perm_addr, addr, ETH_ALEN); 1231} 1232 1233static inline struct ieee80211_rate * 1234ieee80211_get_tx_rate(const struct ieee80211_hw *hw, 1235 const struct ieee80211_tx_info *c) 1236{ 1237 if (WARN_ON(c->control.rates[0].idx < 0)) 1238 return NULL; 1239 return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[0].idx]; 1240} 1241 1242static inline struct ieee80211_rate * 1243ieee80211_get_rts_cts_rate(const struct ieee80211_hw *hw, 1244 const struct ieee80211_tx_info *c) 1245{ 1246 if (c->control.rts_cts_rate_idx < 0) 1247 return NULL; 1248 return &hw->wiphy->bands[c->band]->bitrates[c->control.rts_cts_rate_idx]; 1249} 1250 1251static inline struct ieee80211_rate * 1252ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw, 1253 const struct ieee80211_tx_info *c, int idx) 1254{ 1255 if (c->control.rates[idx + 1].idx < 0) 1256 return NULL; 1257 return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[idx + 1].idx]; 1258} 1259 1260/** 1261 * DOC: Hardware crypto acceleration 1262 * 1263 * mac80211 is capable of taking advantage of many hardware 1264 * acceleration designs for encryption and decryption operations. 1265 * 1266 * The set_key() callback in the &struct ieee80211_ops for a given 1267 * device is called to enable hardware acceleration of encryption and 1268 * decryption. The callback takes a @sta parameter that will be NULL 1269 * for default keys or keys used for transmission only, or point to 1270 * the station information for the peer for individual keys. 1271 * Multiple transmission keys with the same key index may be used when 1272 * VLANs are configured for an access point. 1273 * 1274 * When transmitting, the TX control data will use the @hw_key_idx 1275 * selected by the driver by modifying the &struct ieee80211_key_conf 1276 * pointed to by the @key parameter to the set_key() function. 1277 * 1278 * The set_key() call for the %SET_KEY command should return 0 if 1279 * the key is now in use, -%EOPNOTSUPP or -%ENOSPC if it couldn't be 1280 * added; if you return 0 then hw_key_idx must be assigned to the 1281 * hardware key index, you are free to use the full u8 range. 1282 * 1283 * When the cmd is %DISABLE_KEY then it must succeed. 1284 * 1285 * Note that it is permissible to not decrypt a frame even if a key 1286 * for it has been uploaded to hardware, the stack will not make any 1287 * decision based on whether a key has been uploaded or not but rather 1288 * based on the receive flags. 1289 * 1290 * The &struct ieee80211_key_conf structure pointed to by the @key 1291 * parameter is guaranteed to be valid until another call to set_key() 1292 * removes it, but it can only be used as a cookie to differentiate 1293 * keys. 1294 * 1295 * In TKIP some HW need to be provided a phase 1 key, for RX decryption 1296 * acceleration (i.e. iwlwifi). Those drivers should provide update_tkip_key 1297 * handler. 1298 * The update_tkip_key() call updates the driver with the new phase 1 key. 1299 * This happens every time the iv16 wraps around (every 65536 packets). The 1300 * set_key() call will happen only once for each key (unless the AP did 1301 * rekeying), it will not include a valid phase 1 key. The valid phase 1 key is 1302 * provided by update_tkip_key only. The trigger that makes mac80211 call this 1303 * handler is software decryption with wrap around of iv16. 1304 */ 1305 1306/** 1307 * DOC: Powersave support 1308 * 1309 * mac80211 has support for various powersave implementations. 1310 * 1311 * First, it can support hardware that handles all powersaving by itself, 1312 * such hardware should simply set the %IEEE80211_HW_SUPPORTS_PS hardware 1313 * flag. In that case, it will be told about the desired powersave mode 1314 * with the %IEEE80211_CONF_PS flag depending on the association status. 1315 * The hardware must take care of sending nullfunc frames when necessary, 1316 * i.e. when entering and leaving powersave mode. The hardware is required 1317 * to look at the AID in beacons and signal to the AP that it woke up when 1318 * it finds traffic directed to it. 1319 * 1320 * %IEEE80211_CONF_PS flag enabled means that the powersave mode defined in 1321 * IEEE 802.11-2007 section 11.2 is enabled. This is not to be confused 1322 * with hardware wakeup and sleep states. Driver is responsible for waking 1323 * up the hardware before issuing commands to the hardware and putting it 1324 * back to sleep at appropriate times. 1325 * 1326 * When PS is enabled, hardware needs to wakeup for beacons and receive the 1327 * buffered multicast/broadcast frames after the beacon. Also it must be 1328 * possible to send frames and receive the acknowledment frame. 1329 * 1330 * Other hardware designs cannot send nullfunc frames by themselves and also 1331 * need software support for parsing the TIM bitmap. This is also supported 1332 * by mac80211 by combining the %IEEE80211_HW_SUPPORTS_PS and 1333 * %IEEE80211_HW_PS_NULLFUNC_STACK flags. The hardware is of course still 1334 * required to pass up beacons. The hardware is still required to handle 1335 * waking up for multicast traffic; if it cannot the driver must handle that 1336 * as best as it can, mac80211 is too slow to do that. 1337 * 1338 * Dynamic powersave is an extension to normal powersave in which the 1339 * hardware stays awake for a user-specified period of time after sending a 1340 * frame so that reply frames need not be buffered and therefore delayed to 1341 * the next wakeup. It's compromise of getting good enough latency when 1342 * there's data traffic and still saving significantly power in idle 1343 * periods. 1344 * 1345 * Dynamic powersave is simply supported by mac80211 enabling and disabling 1346 * PS based on traffic. Driver needs to only set %IEEE80211_HW_SUPPORTS_PS 1347 * flag and mac80211 will handle everything automatically. Additionally, 1348 * hardware having support for the dynamic PS feature may set the 1349 * %IEEE80211_HW_SUPPORTS_DYNAMIC_PS flag to indicate that it can support 1350 * dynamic PS mode itself. The driver needs to look at the 1351 * @dynamic_ps_timeout hardware configuration value and use it that value 1352 * whenever %IEEE80211_CONF_PS is set. In this case mac80211 will disable 1353 * dynamic PS feature in stack and will just keep %IEEE80211_CONF_PS 1354 * enabled whenever user has enabled powersave. 1355 * 1356 * Some hardware need to toggle a single shared antenna between WLAN and 1357 * Bluetooth to facilitate co-existence. These types of hardware set 1358 * limitations on the use of host controlled dynamic powersave whenever there 1359 * is simultaneous WLAN and Bluetooth traffic. For these types of hardware, the 1360 * driver may request temporarily going into full power save, in order to 1361 * enable toggling the antenna between BT and WLAN. If the driver requests 1362 * disabling dynamic powersave, the @dynamic_ps_timeout value will be 1363 * temporarily set to zero until the driver re-enables dynamic powersave. 1364 * 1365 * Driver informs U-APSD client support by enabling 1366 * %IEEE80211_HW_SUPPORTS_UAPSD flag. The mode is configured through the 1367 * uapsd paramater in conf_tx() operation. Hardware needs to send the QoS 1368 * Nullfunc frames and stay awake until the service period has ended. To 1369 * utilize U-APSD, dynamic powersave is disabled for voip AC and all frames 1370 * from that AC are transmitted with powersave enabled. 1371 * 1372 * Note: U-APSD client mode is not yet supported with 1373 * %IEEE80211_HW_PS_NULLFUNC_STACK. 1374 */ 1375 1376/** 1377 * DOC: Beacon filter support 1378 * 1379 * Some hardware have beacon filter support to reduce host cpu wakeups 1380 * which will reduce system power consumption. It usuallly works so that 1381 * the firmware creates a checksum of the beacon but omits all constantly 1382 * changing elements (TSF, TIM etc). Whenever the checksum changes the 1383 * beacon is forwarded to the host, otherwise it will be just dropped. That 1384 * way the host will only receive beacons where some relevant information 1385 * (for example ERP protection or WMM settings) have changed. 1386 * 1387 * Beacon filter support is advertised with the %IEEE80211_HW_BEACON_FILTER 1388 * hardware capability. The driver needs to enable beacon filter support 1389 * whenever power save is enabled, that is %IEEE80211_CONF_PS is set. When 1390 * power save is enabled, the stack will not check for beacon loss and the 1391 * driver needs to notify about loss of beacons with ieee80211_beacon_loss(). 1392 * 1393 * The time (or number of beacons missed) until the firmware notifies the 1394 * driver of a beacon loss event (which in turn causes the driver to call 1395 * ieee80211_beacon_loss()) should be configurable and will be controlled 1396 * by mac80211 and the roaming algorithm in the future. 1397 * 1398 * Since there may be constantly changing information elements that nothing 1399 * in the software stack cares about, we will, in the future, have mac80211 1400 * tell the driver which information elements are interesting in the sense 1401 * that we want to see changes in them. This will include 1402 * - a list of information element IDs 1403 * - a list of OUIs for the vendor information element 1404 * 1405 * Ideally, the hardware would filter out any beacons without changes in the 1406 * requested elements, but if it cannot support that it may, at the expense 1407 * of some efficiency, filter out only a subset. For example, if the device 1408 * doesn't support checking for OUIs it should pass up all changes in all 1409 * vendor information elements. 1410 * 1411 * Note that change, for the sake of simplification, also includes information 1412 * elements appearing or disappearing from the beacon. 1413 * 1414 * Some hardware supports an "ignore list" instead, just make sure nothing 1415 * that was requested is on the ignore list, and include commonly changing 1416 * information element IDs in the ignore list, for example 11 (BSS load) and 1417 * the various vendor-assigned IEs with unknown contents (128, 129, 133-136, 1418 * 149, 150, 155, 156, 173, 176, 178, 179, 219); for forward compatibility 1419 * it could also include some currently unused IDs. 1420 * 1421 * 1422 * In addition to these capabilities, hardware should support notifying the 1423 * host of changes in the beacon RSSI. This is relevant to implement roaming 1424 * when no traffic is flowing (when traffic is flowing we see the RSSI of 1425 * the received data packets). This can consist in notifying the host when 1426 * the RSSI changes significantly or when it drops below or rises above 1427 * configurable thresholds. In the future these thresholds will also be 1428 * configured by mac80211 (which gets them from userspace) to implement 1429 * them as the roaming algorithm requires. 1430 * 1431 * If the hardware cannot implement this, the driver should ask it to 1432 * periodically pass beacon frames to the host so that software can do the 1433 * signal strength threshold checking. 1434 */ 1435 1436/** 1437 * DOC: Spatial multiplexing power save 1438 * 1439 * SMPS (Spatial multiplexing power save) is a mechanism to conserve 1440 * power in an 802.11n implementation. For details on the mechanism 1441 * and rationale, please refer to 802.11 (as amended by 802.11n-2009) 1442 * "11.2.3 SM power save". 1443 * 1444 * The mac80211 implementation is capable of sending action frames 1445 * to update the AP about the station's SMPS mode, and will instruct 1446 * the driver to enter the specific mode. It will also announce the 1447 * requested SMPS mode during the association handshake. Hardware 1448 * support for this feature is required, and can be indicated by 1449 * hardware flags. 1450 * 1451 * The default mode will be "automatic", which nl80211/cfg80211 1452 * defines to be dynamic SMPS in (regular) powersave, and SMPS 1453 * turned off otherwise. 1454 * 1455 * To support this feature, the driver must set the appropriate 1456 * hardware support flags, and handle the SMPS flag to the config() 1457 * operation. It will then with this mechanism be instructed to 1458 * enter the requested SMPS mode while associated to an HT AP. 1459 */ 1460 1461/** 1462 * DOC: Frame filtering 1463 * 1464 * mac80211 requires to see many management frames for proper 1465 * operation, and users may want to see many more frames when 1466 * in monitor mode. However, for best CPU usage and power consumption, 1467 * having as few frames as possible percolate through the stack is 1468 * desirable. Hence, the hardware should filter as much as possible. 1469 * 1470 * To achieve this, mac80211 uses filter flags (see below) to tell 1471 * the driver's configure_filter() function which frames should be 1472 * passed to mac80211 and which should be filtered out. 1473 * 1474 * Before configure_filter() is invoked, the prepare_multicast() 1475 * callback is invoked with the parameters @mc_count and @mc_list 1476 * for the combined multicast address list of all virtual interfaces. 1477 * It's use is optional, and it returns a u64 that is passed to 1478 * configure_filter(). Additionally, configure_filter() has the 1479 * arguments @changed_flags telling which flags were changed and 1480 * @total_flags with the new flag states. 1481 * 1482 * If your device has no multicast address filters your driver will 1483 * need to check both the %FIF_ALLMULTI flag and the @mc_count 1484 * parameter to see whether multicast frames should be accepted 1485 * or dropped. 1486 * 1487 * All unsupported flags in @total_flags must be cleared. 1488 * Hardware does not support a flag if it is incapable of _passing_ 1489 * the frame to the stack. Otherwise the driver must ignore 1490 * the flag, but not clear it. 1491 * You must _only_ clear the flag (announce no support for the 1492 * flag to mac80211) if you are not able to pass the packet type 1493 * to the stack (so the hardware always filters it). 1494 * So for example, you should clear @FIF_CONTROL, if your hardware 1495 * always filters control frames. If your hardware always passes 1496 * control frames to the kernel and is incapable of filtering them, 1497 * you do _not_ clear the @FIF_CONTROL flag. 1498 * This rule applies to all other FIF flags as well. 1499 */ 1500 1501/** 1502 * enum ieee80211_filter_flags - hardware filter flags 1503 * 1504 * These flags determine what the filter in hardware should be 1505 * programmed to let through and what should not be passed to the 1506 * stack. It is always safe to pass more frames than requested, 1507 * but this has negative impact on power consumption. 1508 * 1509 * @FIF_PROMISC_IN_BSS: promiscuous mode within your BSS, 1510 * think of the BSS as your network segment and then this corresponds 1511 * to the regular ethernet device promiscuous mode. 1512 * 1513 * @FIF_ALLMULTI: pass all multicast frames, this is used if requested 1514 * by the user or if the hardware is not capable of filtering by 1515 * multicast address. 1516 * 1517 * @FIF_FCSFAIL: pass frames with failed FCS (but you need to set the 1518 * %RX_FLAG_FAILED_FCS_CRC for them) 1519 * 1520 * @FIF_PLCPFAIL: pass frames with failed PLCP CRC (but you need to set 1521 * the %RX_FLAG_FAILED_PLCP_CRC for them 1522 * 1523 * @FIF_BCN_PRBRESP_PROMISC: This flag is set during scanning to indicate 1524 * to the hardware that it should not filter beacons or probe responses 1525 * by BSSID. Filtering them can greatly reduce the amount of processing 1526 * mac80211 needs to do and the amount of CPU wakeups, so you should 1527 * honour this flag if possible. 1528 * 1529 * @FIF_CONTROL: pass control frames (except for PS Poll), if PROMISC_IN_BSS 1530 * is not set then only those addressed to this station. 1531 * 1532 * @FIF_OTHER_BSS: pass frames destined to other BSSes 1533 * 1534 * @FIF_PSPOLL: pass PS Poll frames, if PROMISC_IN_BSS is not set then only 1535 * those addressed to this station. 1536 * 1537 * @FIF_PROBE_REQ: pass probe request frames 1538 */ 1539enum ieee80211_filter_flags { 1540 FIF_PROMISC_IN_BSS = 1<<0, 1541 FIF_ALLMULTI = 1<<1, 1542 FIF_FCSFAIL = 1<<2, 1543 FIF_PLCPFAIL = 1<<3, 1544 FIF_BCN_PRBRESP_PROMISC = 1<<4, 1545 FIF_CONTROL = 1<<5, 1546 FIF_OTHER_BSS = 1<<6, 1547 FIF_PSPOLL = 1<<7, 1548 FIF_PROBE_REQ = 1<<8, 1549}; 1550 1551/** 1552 * enum ieee80211_ampdu_mlme_action - A-MPDU actions 1553 * 1554 * These flags are used with the ampdu_action() callback in 1555 * &struct ieee80211_ops to indicate which action is needed. 1556 * 1557 * Note that drivers MUST be able to deal with a TX aggregation 1558 * session being stopped even before they OK'ed starting it by 1559 * calling ieee80211_start_tx_ba_cb_irqsafe, because the peer 1560 * might receive the addBA frame and send a delBA right away! 1561 * 1562 * @IEEE80211_AMPDU_RX_START: start Rx aggregation 1563 * @IEEE80211_AMPDU_RX_STOP: stop Rx aggregation 1564 * @IEEE80211_AMPDU_TX_START: start Tx aggregation 1565 * @IEEE80211_AMPDU_TX_STOP: stop Tx aggregation 1566 * @IEEE80211_AMPDU_TX_OPERATIONAL: TX aggregation has become operational 1567 */ 1568enum ieee80211_ampdu_mlme_action { 1569 IEEE80211_AMPDU_RX_START, 1570 IEEE80211_AMPDU_RX_STOP, 1571 IEEE80211_AMPDU_TX_START, 1572 IEEE80211_AMPDU_TX_STOP, 1573 IEEE80211_AMPDU_TX_OPERATIONAL, 1574}; 1575 1576/** 1577 * struct ieee80211_ops - callbacks from mac80211 to the driver 1578 * 1579 * This structure contains various callbacks that the driver may 1580 * handle or, in some cases, must handle, for example to configure 1581 * the hardware to a new channel or to transmit a frame. 1582 * 1583 * @tx: Handler that 802.11 module calls for each transmitted frame. 1584 * skb contains the buffer starting from the IEEE 802.11 header. 1585 * The low-level driver should send the frame out based on 1586 * configuration in the TX control data. This handler should, 1587 * preferably, never fail and stop queues appropriately, more 1588 * importantly, however, it must never fail for A-MPDU-queues. 1589 * This function should return NETDEV_TX_OK except in very 1590 * limited cases. 1591 * Must be implemented and atomic. 1592 * 1593 * @start: Called before the first netdevice attached to the hardware 1594 * is enabled. This should turn on the hardware and must turn on 1595 * frame reception (for possibly enabled monitor interfaces.) 1596 * Returns negative error codes, these may be seen in userspace, 1597 * or zero. 1598 * When the device is started it should not have a MAC address 1599 * to avoid acknowledging frames before a non-monitor device 1600 * is added. 1601 * Must be implemented and can sleep. 1602 * 1603 * @stop: Called after last netdevice attached to the hardware 1604 * is disabled. This should turn off the hardware (at least 1605 * it must turn off frame reception.) 1606 * May be called right after add_interface if that rejects 1607 * an interface. If you added any work onto the mac80211 workqueue 1608 * you should ensure to cancel it on this callback. 1609 * Must be implemented and can sleep. 1610 * 1611 * @suspend: Suspend the device; mac80211 itself will quiesce before and 1612 * stop transmitting and doing any other configuration, and then 1613 * ask the device to suspend. This is only invoked when WoWLAN is 1614 * configured, otherwise the device is deconfigured completely and 1615 * reconfigured at resume time. 1616 * The driver may also impose special conditions under which it 1617 * wants to use the "normal" suspend (deconfigure), say if it only 1618 * supports WoWLAN when the device is associated. In this case, it 1619 * must return 1 from this function. 1620 * 1621 * @resume: If WoWLAN was configured, this indicates that mac80211 is 1622 * now resuming its operation, after this the device must be fully 1623 * functional again. If this returns an error, the only way out is 1624 * to also unregister the device. If it returns 1, then mac80211 1625 * will also go through the regular complete restart on resume. 1626 * 1627 * @add_interface: Called when a netdevice attached to the hardware is 1628 * enabled. Because it is not called for monitor mode devices, @start 1629 * and @stop must be implemented. 1630 * The driver should perform any initialization it needs before 1631 * the device can be enabled. The initial configuration for the 1632 * interface is given in the conf parameter. 1633 * The callback may refuse to add an interface by returning a 1634 * negative error code (which will be seen in userspace.) 1635 * Must be implemented and can sleep. 1636 * 1637 * @change_interface: Called when a netdevice changes type. This callback 1638 * is optional, but only if it is supported can interface types be 1639 * switched while the interface is UP. The callback may sleep. 1640 * Note that while an interface is being switched, it will not be 1641 * found by the interface iteration callbacks. 1642 * 1643 * @remove_interface: Notifies a driver that an interface is going down. 1644 * The @stop callback is called after this if it is the last interface 1645 * and no monitor interfaces are present. 1646 * When all interfaces are removed, the MAC address in the hardware 1647 * must be cleared so the device no longer acknowledges packets, 1648 * the mac_addr member of the conf structure is, however, set to the 1649 * MAC address of the device going away. 1650 * Hence, this callback must be implemented. It can sleep. 1651 * 1652 * @config: Handler for configuration requests. IEEE 802.11 code calls this 1653 * function to change hardware configuration, e.g., channel. 1654 * This function should never fail but returns a negative error code 1655 * if it does. The callback can sleep. 1656 * 1657 * @bss_info_changed: Handler for configuration requests related to BSS 1658 * parameters that may vary during BSS's lifespan, and may affect low 1659 * level driver (e.g. assoc/disassoc status, erp parameters). 1660 * This function should not be used if no BSS has been set, unless 1661 * for association indication. The @changed parameter indicates which 1662 * of the bss parameters has changed when a call is made. The callback 1663 * can sleep. 1664 * 1665 * @prepare_multicast: Prepare for multicast filter configuration. 1666 * This callback is optional, and its return value is passed 1667 * to configure_filter(). This callback must be atomic. 1668 * 1669 * @configure_filter: Configure the device's RX filter. 1670 * See the section "Frame filtering" for more information. 1671 * This callback must be implemented and can sleep. 1672 * 1673 * @set_tim: Set TIM bit. mac80211 calls this function when a TIM bit 1674 * must be set or cleared for a given STA. Must be atomic. 1675 * 1676 * @set_key: See the section "Hardware crypto acceleration" 1677 * This callback is only called between add_interface and 1678 * remove_interface calls, i.e. while the given virtual interface 1679 * is enabled. 1680 * Returns a negative error code if the key can't be added. 1681 * The callback can sleep. 1682 * 1683 * @update_tkip_key: See the section "Hardware crypto acceleration" 1684 * This callback will be called in the context of Rx. Called for drivers 1685 * which set IEEE80211_KEY_FLAG_TKIP_REQ_RX_P1_KEY. 1686 * The callback must be atomic. 1687 * 1688 * @set_rekey_data: If the device supports GTK rekeying, for example while the 1689 * host is suspended, it can assign this callback to retrieve the data 1690 * necessary to do GTK rekeying, this is the KEK, KCK and replay counter. 1691 * After rekeying was done it should (for example during resume) notify 1692 * userspace of the new replay counter using ieee80211_gtk_rekey_notify(). 1693 * 1694 * @hw_scan: Ask the hardware to service the scan request, no need to start 1695 * the scan state machine in stack. The scan must honour the channel 1696 * configuration done by the regulatory agent in the wiphy's 1697 * registered bands. The hardware (or the driver) needs to make sure 1698 * that power save is disabled. 1699 * The @req ie/ie_len members are rewritten by mac80211 to contain the 1700 * entire IEs after the SSID, so that drivers need not look at these 1701 * at all but just send them after the SSID -- mac80211 includes the 1702 * (extended) supported rates and HT information (where applicable). 1703 * When the scan finishes, ieee80211_scan_completed() must be called; 1704 * note that it also must be called when the scan cannot finish due to 1705 * any error unless this callback returned a negative error code. 1706 * The callback can sleep. 1707 * 1708 * @cancel_hw_scan: Ask the low-level tp cancel the active hw scan. 1709 * The driver should ask the hardware to cancel the scan (if possible), 1710 * but the scan will be completed only after the driver will call 1711 * ieee80211_scan_completed(). 1712 * This callback is needed for wowlan, to prevent enqueueing a new 1713 * scan_work after the low-level driver was already suspended. 1714 * The callback can sleep. 1715 * 1716 * @sched_scan_start: Ask the hardware to start scanning repeatedly at 1717 * specific intervals. The driver must call the 1718 * ieee80211_sched_scan_results() function whenever it finds results. 1719 * This process will continue until sched_scan_stop is called. 1720 * 1721 * @sched_scan_stop: Tell the hardware to stop an ongoing scheduled scan. 1722 * 1723 * @sw_scan_start: Notifier function that is called just before a software scan 1724 * is started. Can be NULL, if the driver doesn't need this notification. 1725 * The callback can sleep. 1726 * 1727 * @sw_scan_complete: Notifier function that is called just after a 1728 * software scan finished. Can be NULL, if the driver doesn't need 1729 * this notification. 1730 * The callback can sleep. 1731 * 1732 * @get_stats: Return low-level statistics. 1733 * Returns zero if statistics are available. 1734 * The callback can sleep. 1735 * 1736 * @get_tkip_seq: If your device implements TKIP encryption in hardware this 1737 * callback should be provided to read the TKIP transmit IVs (both IV32 1738 * and IV16) for the given key from hardware. 1739 * The callback must be atomic. 1740 * 1741 * @set_frag_threshold: Configuration of fragmentation threshold. Assign this 1742 * if the device does fragmentation by itself; if this callback is 1743 * implemented then the stack will not do fragmentation. 1744 * The callback can sleep. 1745 * 1746 * @set_rts_threshold: Configuration of RTS threshold (if device needs it) 1747 * The callback can sleep. 1748 * 1749 * @sta_add: Notifies low level driver about addition of an associated station, 1750 * AP, IBSS/WDS/mesh peer etc. This callback can sleep. 1751 * 1752 * @sta_remove: Notifies low level driver about removal of an associated 1753 * station, AP, IBSS/WDS/mesh peer etc. This callback can sleep. 1754 * 1755 * @sta_notify: Notifies low level driver about power state transition of an 1756 * associated station, AP, IBSS/WDS/mesh peer etc. For a VIF operating 1757 * in AP mode, this callback will not be called when the flag 1758 * %IEEE80211_HW_AP_LINK_PS is set. Must be atomic. 1759 * 1760 * @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max), 1761 * bursting) for a hardware TX queue. 1762 * Returns a negative error code on failure. 1763 * The callback can sleep. 1764 * 1765 * @get_tsf: Get the current TSF timer value from firmware/hardware. Currently, 1766 * this is only used for IBSS mode BSSID merging and debugging. Is not a 1767 * required function. 1768 * The callback can sleep. 1769 * 1770 * @set_tsf: Set the TSF timer to the specified value in the firmware/hardware. 1771 * Currently, this is only used for IBSS mode debugging. Is not a 1772 * required function. 1773 * The callback can sleep. 1774 * 1775 * @reset_tsf: Reset the TSF timer and allow firmware/hardware to synchronize 1776 * with other STAs in the IBSS. This is only used in IBSS mode. This 1777 * function is optional if the firmware/hardware takes full care of 1778 * TSF synchronization. 1779 * The callback can sleep. 1780 * 1781 * @tx_last_beacon: Determine whether the last IBSS beacon was sent by us. 1782 * This is needed only for IBSS mode and the result of this function is 1783 * used to determine whether to reply to Probe Requests. 1784 * Returns non-zero if this device sent the last beacon. 1785 * The callback can sleep. 1786 * 1787 * @ampdu_action: Perform a certain A-MPDU action 1788 * The RA/TID combination determines the destination and TID we want 1789 * the ampdu action to be performed for. The action is defined through 1790 * ieee80211_ampdu_mlme_action. Starting sequence number (@ssn) 1791 * is the first frame we expect to perform the action on. Notice 1792 * that TX/RX_STOP can pass NULL for this parameter. 1793 * The @buf_size parameter is only valid when the action is set to 1794 * %IEEE80211_AMPDU_TX_OPERATIONAL and indicates the peer's reorder 1795 * buffer size (number of subframes) for this session -- the driver 1796 * may neither send aggregates containing more subframes than this 1797 * nor send aggregates in a way that lost frames would exceed the 1798 * buffer size. If just limiting the aggregate size, this would be 1799 * possible with a buf_size of 8: 1800 * - TX: 1.....7 1801 * - RX: 2....7 (lost frame #1) 1802 * - TX: 8..1... 1803 * which is invalid since #1 was now re-transmitted well past the 1804 * buffer size of 8. Correct ways to retransmit #1 would be: 1805 * - TX: 1 or 18 or 81 1806 * Even "189" would be wrong since 1 could be lost again. 1807 * 1808 * Returns a negative error code on failure. 1809 * The callback can sleep. 1810 * 1811 * @get_survey: Return per-channel survey information 1812 * 1813 * @rfkill_poll: Poll rfkill hardware state. If you need this, you also 1814 * need to set wiphy->rfkill_poll to %true before registration, 1815 * and need to call wiphy_rfkill_set_hw_state() in the callback. 1816 * The callback can sleep. 1817 * 1818 * @set_coverage_class: Set slot time for given coverage class as specified 1819 * in IEEE 802.11-2007 section 17.3.8.6 and modify ACK timeout 1820 * accordingly. This callback is not required and may sleep. 1821 * 1822 * @testmode_cmd: Implement a cfg80211 test mode command. 1823 * The callback can sleep. 1824 * @testmode_dump: Implement a cfg80211 test mode dump. The callback can sleep. 1825 * 1826 * @flush: Flush all pending frames from the hardware queue, making sure 1827 * that the hardware queues are empty. If the parameter @drop is set 1828 * to %true, pending frames may be dropped. The callback can sleep. 1829 * 1830 * @channel_switch: Drivers that need (or want) to offload the channel 1831 * switch operation for CSAs received from the AP may implement this 1832 * callback. They must then call ieee80211_chswitch_done() to indicate 1833 * completion of the channel switch. 1834 * 1835 * @napi_poll: Poll Rx queue for incoming data frames. 1836 * 1837 * @set_antenna: Set antenna configuration (tx_ant, rx_ant) on the device. 1838 * Parameters are bitmaps of allowed antennas to use for TX/RX. Drivers may 1839 * reject TX/RX mask combinations they cannot support by returning -EINVAL 1840 * (also see nl80211.h @NL80211_ATTR_WIPHY_ANTENNA_TX). 1841 * 1842 * @get_antenna: Get current antenna configuration from device (tx_ant, rx_ant). 1843 * 1844 * @remain_on_channel: Starts an off-channel period on the given channel, must 1845 * call back to ieee80211_ready_on_channel() when on that channel. Note 1846 * that normal channel traffic is not stopped as this is intended for hw 1847 * offload. Frames to transmit on the off-channel channel are transmitted 1848 * normally except for the %IEEE80211_TX_CTL_TX_OFFCHAN flag. When the 1849 * duration (which will always be non-zero) expires, the driver must call 1850 * ieee80211_remain_on_channel_expired(). This callback may sleep. 1851 * @cancel_remain_on_channel: Requests that an ongoing off-channel period is 1852 * aborted before it expires. This callback may sleep. 1853 * @offchannel_tx: Transmit frame on another channel, wait for a response 1854 * and return. Reliable TX status must be reported for the frame. If the 1855 * return value is 1, then the @remain_on_channel will be used with a 1856 * regular transmission (if supported.) 1857 * @offchannel_tx_cancel_wait: cancel wait associated with offchannel TX 1858 * 1859 * @set_ringparam: Set tx and rx ring sizes. 1860 * 1861 * @get_ringparam: Get tx and rx ring current and maximum sizes. 1862 * 1863 * @tx_frames_pending: Check if there is any pending frame in the hardware 1864 * queues before entering power save. 1865 * 1866 * @set_bitrate_mask: Set a mask of rates to be used for rate control selection 1867 * when transmitting a frame. Currently only legacy rates are handled. 1868 * The callback can sleep. 1869 */ 1870struct ieee80211_ops { 1871 void (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb); 1872 int (*start)(struct ieee80211_hw *hw); 1873 void (*stop)(struct ieee80211_hw *hw); 1874#ifdef CONFIG_PM 1875 int (*suspend)(struct ieee80211_hw *hw, struct cfg80211_wowlan *wowlan); 1876 int (*resume)(struct ieee80211_hw *hw); 1877#endif 1878 int (*add_interface)(struct ieee80211_hw *hw, 1879 struct ieee80211_vif *vif); 1880 int (*change_interface)(struct ieee80211_hw *hw, 1881 struct ieee80211_vif *vif, 1882 enum nl80211_iftype new_type, bool p2p); 1883 void (*remove_interface)(struct ieee80211_hw *hw, 1884 struct ieee80211_vif *vif); 1885 int (*config)(struct ieee80211_hw *hw, u32 changed); 1886 void (*bss_info_changed)(struct ieee80211_hw *hw, 1887 struct ieee80211_vif *vif, 1888 struct ieee80211_bss_conf *info, 1889 u32 changed); 1890 u64 (*prepare_multicast)(struct ieee80211_hw *hw, 1891 struct netdev_hw_addr_list *mc_list); 1892 void (*configure_filter)(struct ieee80211_hw *hw, 1893 unsigned int changed_flags, 1894 unsigned int *total_flags, 1895 u64 multicast); 1896 int (*set_tim)(struct ieee80211_hw *hw, struct ieee80211_sta *sta, 1897 bool set); 1898 int (*set_key)(struct ieee80211_hw *hw, enum set_key_cmd cmd, 1899 struct ieee80211_vif *vif, struct ieee80211_sta *sta, 1900 struct ieee80211_key_conf *key); 1901 void (*update_tkip_key)(struct ieee80211_hw *hw, 1902 struct ieee80211_vif *vif, 1903 struct ieee80211_key_conf *conf, 1904 struct ieee80211_sta *sta, 1905 u32 iv32, u16 *phase1key); 1906 void (*set_rekey_data)(struct ieee80211_hw *hw, 1907 struct ieee80211_vif *vif, 1908 struct cfg80211_gtk_rekey_data *data); 1909 int (*hw_scan)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 1910 struct cfg80211_scan_request *req); 1911 void (*cancel_hw_scan)(struct ieee80211_hw *hw, 1912 struct ieee80211_vif *vif); 1913 int (*sched_scan_start)(struct ieee80211_hw *hw, 1914 struct ieee80211_vif *vif, 1915 struct cfg80211_sched_scan_request *req, 1916 struct ieee80211_sched_scan_ies *ies); 1917 void (*sched_scan_stop)(struct ieee80211_hw *hw, 1918 struct ieee80211_vif *vif); 1919 void (*sw_scan_start)(struct ieee80211_hw *hw); 1920 void (*sw_scan_complete)(struct ieee80211_hw *hw); 1921 int (*get_stats)(struct ieee80211_hw *hw, 1922 struct ieee80211_low_level_stats *stats); 1923 void (*get_tkip_seq)(struct ieee80211_hw *hw, u8 hw_key_idx, 1924 u32 *iv32, u16 *iv16); 1925 int (*set_frag_threshold)(struct ieee80211_hw *hw, u32 value); 1926 int (*set_rts_threshold)(struct ieee80211_hw *hw, u32 value); 1927 int (*sta_add)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 1928 struct ieee80211_sta *sta); 1929 int (*sta_remove)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 1930 struct ieee80211_sta *sta); 1931 void (*sta_notify)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 1932 enum sta_notify_cmd, struct ieee80211_sta *sta); 1933 int (*conf_tx)(struct ieee80211_hw *hw, u16 queue, 1934 const struct ieee80211_tx_queue_params *params); 1935 u64 (*get_tsf)(struct ieee80211_hw *hw); 1936 void (*set_tsf)(struct ieee80211_hw *hw, u64 tsf); 1937 void (*reset_tsf)(struct ieee80211_hw *hw); 1938 int (*tx_last_beacon)(struct ieee80211_hw *hw); 1939 int (*ampdu_action)(struct ieee80211_hw *hw, 1940 struct ieee80211_vif *vif, 1941 enum ieee80211_ampdu_mlme_action action, 1942 struct ieee80211_sta *sta, u16 tid, u16 *ssn, 1943 u8 buf_size); 1944 int (*get_survey)(struct ieee80211_hw *hw, int idx, 1945 struct survey_info *survey); 1946 void (*rfkill_poll)(struct ieee80211_hw *hw); 1947 void (*set_coverage_class)(struct ieee80211_hw *hw, u8 coverage_class); 1948#ifdef CONFIG_NL80211_TESTMODE 1949 int (*testmode_cmd)(struct ieee80211_hw *hw, void *data, int len); 1950 int (*testmode_dump)(struct ieee80211_hw *hw, struct sk_buff *skb, 1951 struct netlink_callback *cb, 1952 void *data, int len); 1953#endif 1954 void (*flush)(struct ieee80211_hw *hw, bool drop); 1955 void (*channel_switch)(struct ieee80211_hw *hw, 1956 struct ieee80211_channel_switch *ch_switch); 1957 int (*napi_poll)(struct ieee80211_hw *hw, int budget); 1958 int (*set_antenna)(struct ieee80211_hw *hw, u32 tx_ant, u32 rx_ant); 1959 int (*get_antenna)(struct ieee80211_hw *hw, u32 *tx_ant, u32 *rx_ant); 1960 1961 int (*remain_on_channel)(struct ieee80211_hw *hw, 1962 struct ieee80211_channel *chan, 1963 enum nl80211_channel_type channel_type, 1964 int duration); 1965 int (*cancel_remain_on_channel)(struct ieee80211_hw *hw); 1966 int (*offchannel_tx)(struct ieee80211_hw *hw, struct sk_buff *skb, 1967 struct ieee80211_channel *chan, 1968 enum nl80211_channel_type channel_type, 1969 unsigned int wait); 1970 int (*offchannel_tx_cancel_wait)(struct ieee80211_hw *hw); 1971 int (*set_ringparam)(struct ieee80211_hw *hw, u32 tx, u32 rx); 1972 void (*get_ringparam)(struct ieee80211_hw *hw, 1973 u32 *tx, u32 *tx_max, u32 *rx, u32 *rx_max); 1974 bool (*tx_frames_pending)(struct ieee80211_hw *hw); 1975 int (*set_bitrate_mask)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 1976 const struct cfg80211_bitrate_mask *mask); 1977}; 1978 1979/** 1980 * ieee80211_alloc_hw - Allocate a new hardware device 1981 * 1982 * This must be called once for each hardware device. The returned pointer 1983 * must be used to refer to this device when calling other functions. 1984 * mac80211 allocates a private data area for the driver pointed to by 1985 * @priv in &struct ieee80211_hw, the size of this area is given as 1986 * @priv_data_len. 1987 * 1988 * @priv_data_len: length of private data 1989 * @ops: callbacks for this device 1990 */ 1991struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len, 1992 const struct ieee80211_ops *ops); 1993 1994/** 1995 * ieee80211_register_hw - Register hardware device 1996 * 1997 * You must call this function before any other functions in 1998 * mac80211. Note that before a hardware can be registered, you 1999 * need to fill the contained wiphy's information. 2000 * 2001 * @hw: the device to register as returned by ieee80211_alloc_hw() 2002 */ 2003int ieee80211_register_hw(struct ieee80211_hw *hw); 2004 2005/** 2006 * struct ieee80211_tpt_blink - throughput blink description 2007 * @throughput: throughput in Kbit/sec 2008 * @blink_time: blink time in milliseconds 2009 * (full cycle, ie. one off + one on period) 2010 */ 2011struct ieee80211_tpt_blink { 2012 int throughput; 2013 int blink_time; 2014}; 2015 2016/** 2017 * enum ieee80211_tpt_led_trigger_flags - throughput trigger flags 2018 * @IEEE80211_TPT_LEDTRIG_FL_RADIO: enable blinking with radio 2019 * @IEEE80211_TPT_LEDTRIG_FL_WORK: enable blinking when working 2020 * @IEEE80211_TPT_LEDTRIG_FL_CONNECTED: enable blinking when at least one 2021 * interface is connected in some way, including being an AP 2022 */ 2023enum ieee80211_tpt_led_trigger_flags { 2024 IEEE80211_TPT_LEDTRIG_FL_RADIO = BIT(0), 2025 IEEE80211_TPT_LEDTRIG_FL_WORK = BIT(1), 2026 IEEE80211_TPT_LEDTRIG_FL_CONNECTED = BIT(2), 2027}; 2028 2029#ifdef CONFIG_MAC80211_LEDS 2030extern char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw); 2031extern char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw); 2032extern char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw); 2033extern char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw); 2034extern char *__ieee80211_create_tpt_led_trigger( 2035 struct ieee80211_hw *hw, unsigned int flags, 2036 const struct ieee80211_tpt_blink *blink_table, 2037 unsigned int blink_table_len); 2038#endif 2039/** 2040 * ieee80211_get_tx_led_name - get name of TX LED 2041 * 2042 * mac80211 creates a transmit LED trigger for each wireless hardware 2043 * that can be used to drive LEDs if your driver registers a LED device. 2044 * This function returns the name (or %NULL if not configured for LEDs) 2045 * of the trigger so you can automatically link the LED device. 2046 * 2047 * @hw: the hardware to get the LED trigger name for 2048 */ 2049static inline char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw) 2050{ 2051#ifdef CONFIG_MAC80211_LEDS 2052 return __ieee80211_get_tx_led_name(hw); 2053#else 2054 return NULL; 2055#endif 2056} 2057 2058/** 2059 * ieee80211_get_rx_led_name - get name of RX LED 2060 * 2061 * mac80211 creates a receive LED trigger for each wireless hardware 2062 * that can be used to drive LEDs if your driver registers a LED device. 2063 * This function returns the name (or %NULL if not configured for LEDs) 2064 * of the trigger so you can automatically link the LED device. 2065 * 2066 * @hw: the hardware to get the LED trigger name for 2067 */ 2068static inline char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw) 2069{ 2070#ifdef CONFIG_MAC80211_LEDS 2071 return __ieee80211_get_rx_led_name(hw); 2072#else 2073 return NULL; 2074#endif 2075} 2076 2077/** 2078 * ieee80211_get_assoc_led_name - get name of association LED 2079 * 2080 * mac80211 creates a association LED trigger for each wireless hardware 2081 * that can be used to drive LEDs if your driver registers a LED device. 2082 * This function returns the name (or %NULL if not configured for LEDs) 2083 * of the trigger so you can automatically link the LED device. 2084 * 2085 * @hw: the hardware to get the LED trigger name for 2086 */ 2087static inline char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw) 2088{ 2089#ifdef CONFIG_MAC80211_LEDS 2090 return __ieee80211_get_assoc_led_name(hw); 2091#else 2092 return NULL; 2093#endif 2094} 2095 2096/** 2097 * ieee80211_get_radio_led_name - get name of radio LED 2098 * 2099 * mac80211 creates a radio change LED trigger for each wireless hardware 2100 * that can be used to drive LEDs if your driver registers a LED device. 2101 * This function returns the name (or %NULL if not configured for LEDs) 2102 * of the trigger so you can automatically link the LED device. 2103 * 2104 * @hw: the hardware to get the LED trigger name for 2105 */ 2106static inline char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw) 2107{ 2108#ifdef CONFIG_MAC80211_LEDS 2109 return __ieee80211_get_radio_led_name(hw); 2110#else 2111 return NULL; 2112#endif 2113} 2114 2115/** 2116 * ieee80211_create_tpt_led_trigger - create throughput LED trigger 2117 * @hw: the hardware to create the trigger for 2118 * @flags: trigger flags, see &enum ieee80211_tpt_led_trigger_flags 2119 * @blink_table: the blink table -- needs to be ordered by throughput 2120 * @blink_table_len: size of the blink table 2121 * 2122 * This function returns %NULL (in case of error, or if no LED 2123 * triggers are configured) or the name of the new trigger. 2124 * This function must be called before ieee80211_register_hw(). 2125 */ 2126static inline char * 2127ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw, unsigned int flags, 2128 const struct ieee80211_tpt_blink *blink_table, 2129 unsigned int blink_table_len) 2130{ 2131#ifdef CONFIG_MAC80211_LEDS 2132 return __ieee80211_create_tpt_led_trigger(hw, flags, blink_table, 2133 blink_table_len); 2134#else 2135 return NULL; 2136#endif 2137} 2138 2139/** 2140 * ieee80211_unregister_hw - Unregister a hardware device 2141 * 2142 * This function instructs mac80211 to free allocated resources 2143 * and unregister netdevices from the networking subsystem. 2144 * 2145 * @hw: the hardware to unregister 2146 */ 2147void ieee80211_unregister_hw(struct ieee80211_hw *hw); 2148 2149/** 2150 * ieee80211_free_hw - free hardware descriptor 2151 * 2152 * This function frees everything that was allocated, including the 2153 * private data for the driver. You must call ieee80211_unregister_hw() 2154 * before calling this function. 2155 * 2156 * @hw: the hardware to free 2157 */ 2158void ieee80211_free_hw(struct ieee80211_hw *hw); 2159 2160/** 2161 * ieee80211_restart_hw - restart hardware completely 2162 * 2163 * Call this function when the hardware was restarted for some reason 2164 * (hardware error, ...) and the driver is unable to restore its state 2165 * by itself. mac80211 assumes that at this point the driver/hardware 2166 * is completely uninitialised and stopped, it starts the process by 2167 * calling the ->start() operation. The driver will need to reset all 2168 * internal state that it has prior to calling this function. 2169 * 2170 * @hw: the hardware to restart 2171 */ 2172void ieee80211_restart_hw(struct ieee80211_hw *hw); 2173 2174/** ieee80211_napi_schedule - schedule NAPI poll 2175 * 2176 * Use this function to schedule NAPI polling on a device. 2177 * 2178 * @hw: the hardware to start polling 2179 */ 2180void ieee80211_napi_schedule(struct ieee80211_hw *hw); 2181 2182/** ieee80211_napi_complete - complete NAPI polling 2183 * 2184 * Use this function to finish NAPI polling on a device. 2185 * 2186 * @hw: the hardware to stop polling 2187 */ 2188void ieee80211_napi_complete(struct ieee80211_hw *hw); 2189 2190/** 2191 * ieee80211_rx - receive frame 2192 * 2193 * Use this function to hand received frames to mac80211. The receive 2194 * buffer in @skb must start with an IEEE 802.11 header. In case of a 2195 * paged @skb is used, the driver is recommended to put the ieee80211 2196 * header of the frame on the linear part of the @skb to avoid memory 2197 * allocation and/or memcpy by the stack. 2198 * 2199 * This function may not be called in IRQ context. Calls to this function 2200 * for a single hardware must be synchronized against each other. Calls to 2201 * this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be 2202 * mixed for a single hardware. 2203 * 2204 * In process context use instead ieee80211_rx_ni(). 2205 * 2206 * @hw: the hardware this frame came in on 2207 * @skb: the buffer to receive, owned by mac80211 after this call 2208 */ 2209void ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb); 2210 2211/** 2212 * ieee80211_rx_irqsafe - receive frame 2213 * 2214 * Like ieee80211_rx() but can be called in IRQ context 2215 * (internally defers to a tasklet.) 2216 * 2217 * Calls to this function, ieee80211_rx() or ieee80211_rx_ni() may not 2218 * be mixed for a single hardware. 2219 * 2220 * @hw: the hardware this frame came in on 2221 * @skb: the buffer to receive, owned by mac80211 after this call 2222 */ 2223void ieee80211_rx_irqsafe(struct ieee80211_hw *hw, struct sk_buff *skb); 2224 2225/** 2226 * ieee80211_rx_ni - receive frame (in process context) 2227 * 2228 * Like ieee80211_rx() but can be called in process context 2229 * (internally disables bottom halves). 2230 * 2231 * Calls to this function, ieee80211_rx() and ieee80211_rx_irqsafe() may 2232 * not be mixed for a single hardware. 2233 * 2234 * @hw: the hardware this frame came in on 2235 * @skb: the buffer to receive, owned by mac80211 after this call 2236 */ 2237static inline void ieee80211_rx_ni(struct ieee80211_hw *hw, 2238 struct sk_buff *skb) 2239{ 2240 local_bh_disable(); 2241 ieee80211_rx(hw, skb); 2242 local_bh_enable(); 2243} 2244 2245/** 2246 * ieee80211_sta_ps_transition - PS transition for connected sta 2247 * 2248 * When operating in AP mode with the %IEEE80211_HW_AP_LINK_PS 2249 * flag set, use this function to inform mac80211 about a connected station 2250 * entering/leaving PS mode. 2251 * 2252 * This function may not be called in IRQ context or with softirqs enabled. 2253 * 2254 * Calls to this function for a single hardware must be synchronized against 2255 * each other. 2256 * 2257 * The function returns -EINVAL when the requested PS mode is already set. 2258 * 2259 * @sta: currently connected sta 2260 * @start: start or stop PS 2261 */ 2262int ieee80211_sta_ps_transition(struct ieee80211_sta *sta, bool start); 2263 2264/** 2265 * ieee80211_sta_ps_transition_ni - PS transition for connected sta 2266 * (in process context) 2267 * 2268 * Like ieee80211_sta_ps_transition() but can be called in process context 2269 * (internally disables bottom halves). Concurrent call restriction still 2270 * applies. 2271 * 2272 * @sta: currently connected sta 2273 * @start: start or stop PS 2274 */ 2275static inline int ieee80211_sta_ps_transition_ni(struct ieee80211_sta *sta, 2276 bool start) 2277{ 2278 int ret; 2279 2280 local_bh_disable(); 2281 ret = ieee80211_sta_ps_transition(sta, start); 2282 local_bh_enable(); 2283 2284 return ret; 2285} 2286 2287/* 2288 * The TX headroom reserved by mac80211 for its own tx_status functions. 2289 * This is enough for the radiotap header. 2290 */ 2291#define IEEE80211_TX_STATUS_HEADROOM 13 2292 2293/** 2294 * ieee80211_sta_set_tim - set the TIM bit for a sleeping station 2295 * @sta: &struct ieee80211_sta pointer for the sleeping station 2296 * 2297 * If a driver buffers frames for a powersave station instead of passing 2298 * them back to mac80211 for retransmission, the station needs to be told 2299 * to wake up using the TIM bitmap in the beacon. 2300 * 2301 * This function sets the station's TIM bit - it will be cleared when the 2302 * station wakes up. 2303 */ 2304void ieee80211_sta_set_tim(struct ieee80211_sta *sta); 2305 2306/** 2307 * ieee80211_tx_status - transmit status callback 2308 * 2309 * Call this function for all transmitted frames after they have been 2310 * transmitted. It is permissible to not call this function for 2311 * multicast frames but this can affect statistics. 2312 * 2313 * This function may not be called in IRQ context. Calls to this function 2314 * for a single hardware must be synchronized against each other. Calls 2315 * to this function, ieee80211_tx_status_ni() and ieee80211_tx_status_irqsafe() 2316 * may not be mixed for a single hardware. 2317 * 2318 * @hw: the hardware the frame was transmitted by 2319 * @skb: the frame that was transmitted, owned by mac80211 after this call 2320 */ 2321void ieee80211_tx_status(struct ieee80211_hw *hw, 2322 struct sk_buff *skb); 2323 2324/** 2325 * ieee80211_tx_status_ni - transmit status callback (in process context) 2326 * 2327 * Like ieee80211_tx_status() but can be called in process context. 2328 * 2329 * Calls to this function, ieee80211_tx_status() and 2330 * ieee80211_tx_status_irqsafe() may not be mixed 2331 * for a single hardware. 2332 * 2333 * @hw: the hardware the frame was transmitted by 2334 * @skb: the frame that was transmitted, owned by mac80211 after this call 2335 */ 2336static inline void ieee80211_tx_status_ni(struct ieee80211_hw *hw, 2337 struct sk_buff *skb) 2338{ 2339 local_bh_disable(); 2340 ieee80211_tx_status(hw, skb); 2341 local_bh_enable(); 2342} 2343 2344/** 2345 * ieee80211_tx_status_irqsafe - IRQ-safe transmit status callback 2346 * 2347 * Like ieee80211_tx_status() but can be called in IRQ context 2348 * (internally defers to a tasklet.) 2349 * 2350 * Calls to this function, ieee80211_tx_status() and 2351 * ieee80211_tx_status_ni() may not be mixed for a single hardware. 2352 * 2353 * @hw: the hardware the frame was transmitted by 2354 * @skb: the frame that was transmitted, owned by mac80211 after this call 2355 */ 2356void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw, 2357 struct sk_buff *skb); 2358 2359/** 2360 * ieee80211_report_low_ack - report non-responding station 2361 * 2362 * When operating in AP-mode, call this function to report a non-responding 2363 * connected STA. 2364 * 2365 * @sta: the non-responding connected sta 2366 * @num_packets: number of packets sent to @sta without a response 2367 */ 2368void ieee80211_report_low_ack(struct ieee80211_sta *sta, u32 num_packets); 2369 2370/** 2371 * ieee80211_beacon_get_tim - beacon generation function 2372 * @hw: pointer obtained from ieee80211_alloc_hw(). 2373 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 2374 * @tim_offset: pointer to variable that will receive the TIM IE offset. 2375 * Set to 0 if invalid (in non-AP modes). 2376 * @tim_length: pointer to variable that will receive the TIM IE length, 2377 * (including the ID and length bytes!). 2378 * Set to 0 if invalid (in non-AP modes). 2379 * 2380 * If the driver implements beaconing modes, it must use this function to 2381 * obtain the beacon frame/template. 2382 * 2383 * If the beacon frames are generated by the host system (i.e., not in 2384 * hardware/firmware), the driver uses this function to get each beacon 2385 * frame from mac80211 -- it is responsible for calling this function 2386 * before the beacon is needed (e.g. based on hardware interrupt). 2387 * 2388 * If the beacon frames are generated by the device, then the driver 2389 * must use the returned beacon as the template and change the TIM IE 2390 * according to the current DTIM parameters/TIM bitmap. 2391 * 2392 * The driver is responsible for freeing the returned skb. 2393 */ 2394struct sk_buff *ieee80211_beacon_get_tim(struct ieee80211_hw *hw, 2395 struct ieee80211_vif *vif, 2396 u16 *tim_offset, u16 *tim_length); 2397 2398/** 2399 * ieee80211_beacon_get - beacon generation function 2400 * @hw: pointer obtained from ieee80211_alloc_hw(). 2401 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 2402 * 2403 * See ieee80211_beacon_get_tim(). 2404 */ 2405static inline struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw, 2406 struct ieee80211_vif *vif) 2407{ 2408 return ieee80211_beacon_get_tim(hw, vif, NULL, NULL); 2409} 2410 2411/** 2412 * ieee80211_pspoll_get - retrieve a PS Poll template 2413 * @hw: pointer obtained from ieee80211_alloc_hw(). 2414 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 2415 * 2416 * Creates a PS Poll a template which can, for example, uploaded to 2417 * hardware. The template must be updated after association so that correct 2418 * AID, BSSID and MAC address is used. 2419 * 2420 * Note: Caller (or hardware) is responsible for setting the 2421 * &IEEE80211_FCTL_PM bit. 2422 */ 2423struct sk_buff *ieee80211_pspoll_get(struct ieee80211_hw *hw, 2424 struct ieee80211_vif *vif); 2425 2426/** 2427 * ieee80211_nullfunc_get - retrieve a nullfunc template 2428 * @hw: pointer obtained from ieee80211_alloc_hw(). 2429 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 2430 * 2431 * Creates a Nullfunc template which can, for example, uploaded to 2432 * hardware. The template must be updated after association so that correct 2433 * BSSID and address is used. 2434 * 2435 * Note: Caller (or hardware) is responsible for setting the 2436 * &IEEE80211_FCTL_PM bit as well as Duration and Sequence Control fields. 2437 */ 2438struct sk_buff *ieee80211_nullfunc_get(struct ieee80211_hw *hw, 2439 struct ieee80211_vif *vif); 2440 2441/** 2442 * ieee80211_probereq_get - retrieve a Probe Request template 2443 * @hw: pointer obtained from ieee80211_alloc_hw(). 2444 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 2445 * @ssid: SSID buffer 2446 * @ssid_len: length of SSID 2447 * @ie: buffer containing all IEs except SSID for the template 2448 * @ie_len: length of the IE buffer 2449 * 2450 * Creates a Probe Request template which can, for example, be uploaded to 2451 * hardware. 2452 */ 2453struct sk_buff *ieee80211_probereq_get(struct ieee80211_hw *hw, 2454 struct ieee80211_vif *vif, 2455 const u8 *ssid, size_t ssid_len, 2456 const u8 *ie, size_t ie_len); 2457 2458/** 2459 * ieee80211_rts_get - RTS frame generation function 2460 * @hw: pointer obtained from ieee80211_alloc_hw(). 2461 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 2462 * @frame: pointer to the frame that is going to be protected by the RTS. 2463 * @frame_len: the frame length (in octets). 2464 * @frame_txctl: &struct ieee80211_tx_info of the frame. 2465 * @rts: The buffer where to store the RTS frame. 2466 * 2467 * If the RTS frames are generated by the host system (i.e., not in 2468 * hardware/firmware), the low-level driver uses this function to receive 2469 * the next RTS frame from the 802.11 code. The low-level is responsible 2470 * for calling this function before and RTS frame is needed. 2471 */ 2472void ieee80211_rts_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 2473 const void *frame, size_t frame_len, 2474 const struct ieee80211_tx_info *frame_txctl, 2475 struct ieee80211_rts *rts); 2476 2477/** 2478 * ieee80211_rts_duration - Get the duration field for an RTS frame 2479 * @hw: pointer obtained from ieee80211_alloc_hw(). 2480 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 2481 * @frame_len: the length of the frame that is going to be protected by the RTS. 2482 * @frame_txctl: &struct ieee80211_tx_info of the frame. 2483 * 2484 * If the RTS is generated in firmware, but the host system must provide 2485 * the duration field, the low-level driver uses this function to receive 2486 * the duration field value in little-endian byteorder. 2487 */ 2488__le16 ieee80211_rts_duration(struct ieee80211_hw *hw, 2489 struct ieee80211_vif *vif, size_t frame_len, 2490 const struct ieee80211_tx_info *frame_txctl); 2491 2492/** 2493 * ieee80211_ctstoself_get - CTS-to-self frame generation function 2494 * @hw: pointer obtained from ieee80211_alloc_hw(). 2495 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 2496 * @frame: pointer to the frame that is going to be protected by the CTS-to-self. 2497 * @frame_len: the frame length (in octets). 2498 * @frame_txctl: &struct ieee80211_tx_info of the frame. 2499 * @cts: The buffer where to store the CTS-to-self frame. 2500 * 2501 * If the CTS-to-self frames are generated by the host system (i.e., not in 2502 * hardware/firmware), the low-level driver uses this function to receive 2503 * the next CTS-to-self frame from the 802.11 code. The low-level is responsible 2504 * for calling this function before and CTS-to-self frame is needed. 2505 */ 2506void ieee80211_ctstoself_get(struct ieee80211_hw *hw, 2507 struct ieee80211_vif *vif, 2508 const void *frame, size_t frame_len, 2509 const struct ieee80211_tx_info *frame_txctl, 2510 struct ieee80211_cts *cts); 2511 2512/** 2513 * ieee80211_ctstoself_duration - Get the duration field for a CTS-to-self frame 2514 * @hw: pointer obtained from ieee80211_alloc_hw(). 2515 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 2516 * @frame_len: the length of the frame that is going to be protected by the CTS-to-self. 2517 * @frame_txctl: &struct ieee80211_tx_info of the frame. 2518 * 2519 * If the CTS-to-self is generated in firmware, but the host system must provide 2520 * the duration field, the low-level driver uses this function to receive 2521 * the duration field value in little-endian byteorder. 2522 */ 2523__le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw, 2524 struct ieee80211_vif *vif, 2525 size_t frame_len, 2526 const struct ieee80211_tx_info *frame_txctl); 2527 2528/** 2529 * ieee80211_generic_frame_duration - Calculate the duration field for a frame 2530 * @hw: pointer obtained from ieee80211_alloc_hw(). 2531 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 2532 * @frame_len: the length of the frame. 2533 * @rate: the rate at which the frame is going to be transmitted. 2534 * 2535 * Calculate the duration field of some generic frame, given its 2536 * length and transmission rate (in 100kbps). 2537 */ 2538__le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw, 2539 struct ieee80211_vif *vif, 2540 size_t frame_len, 2541 struct ieee80211_rate *rate); 2542 2543/** 2544 * ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames 2545 * @hw: pointer as obtained from ieee80211_alloc_hw(). 2546 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 2547 * 2548 * Function for accessing buffered broadcast and multicast frames. If 2549 * hardware/firmware does not implement buffering of broadcast/multicast 2550 * frames when power saving is used, 802.11 code buffers them in the host 2551 * memory. The low-level driver uses this function to fetch next buffered 2552 * frame. In most cases, this is used when generating beacon frame. This 2553 * function returns a pointer to the next buffered skb or NULL if no more 2554 * buffered frames are available. 2555 * 2556 * Note: buffered frames are returned only after DTIM beacon frame was 2557 * generated with ieee80211_beacon_get() and the low-level driver must thus 2558 * call ieee80211_beacon_get() first. ieee80211_get_buffered_bc() returns 2559 * NULL if the previous generated beacon was not DTIM, so the low-level driver 2560 * does not need to check for DTIM beacons separately and should be able to 2561 * use common code for all beacons. 2562 */ 2563struct sk_buff * 2564ieee80211_get_buffered_bc(struct ieee80211_hw *hw, struct ieee80211_vif *vif); 2565 2566/** 2567 * ieee80211_get_tkip_p1k - get a TKIP phase 1 key 2568 * 2569 * This function returns the TKIP phase 1 key for the IV32 taken 2570 * from the given packet. 2571 * 2572 * @keyconf: the parameter passed with the set key 2573 * @skb: the packet to take the IV32 value from that will be encrypted 2574 * with this P1K 2575 * @p1k: a buffer to which the key will be written, as 5 u16 values 2576 */ 2577void ieee80211_get_tkip_p1k(struct ieee80211_key_conf *keyconf, 2578 struct sk_buff *skb, u16 *p1k); 2579 2580/** 2581 * ieee80211_get_tkip_p2k - get a TKIP phase 2 key 2582 * 2583 * This function computes the TKIP RC4 key for the IV values 2584 * in the packet. 2585 * 2586 * @keyconf: the parameter passed with the set key 2587 * @skb: the packet to take the IV32/IV16 values from that will be 2588 * encrypted with this key 2589 * @p2k: a buffer to which the key will be written, 16 bytes 2590 */ 2591void ieee80211_get_tkip_p2k(struct ieee80211_key_conf *keyconf, 2592 struct sk_buff *skb, u8 *p2k); 2593 2594/** 2595 * struct ieee80211_key_seq - key sequence counter 2596 * 2597 * @tkip: TKIP data, containing IV32 and IV16 in host byte order 2598 * @ccmp: PN data, most significant byte first (big endian, 2599 * reverse order than in packet) 2600 * @aes_cmac: PN data, most significant byte first (big endian, 2601 * reverse order than in packet) 2602 */ 2603struct ieee80211_key_seq { 2604 union { 2605 struct { 2606 u32 iv32; 2607 u16 iv16; 2608 } tkip; 2609 struct { 2610 u8 pn[6]; 2611 } ccmp; 2612 struct { 2613 u8 pn[6]; 2614 } aes_cmac; 2615 }; 2616}; 2617 2618/** 2619 * ieee80211_get_key_tx_seq - get key TX sequence counter 2620 * 2621 * @keyconf: the parameter passed with the set key 2622 * @seq: buffer to receive the sequence data 2623 * 2624 * This function allows a driver to retrieve the current TX IV/PN 2625 * for the given key. It must not be called if IV generation is 2626 * offloaded to the device. 2627 * 2628 * Note that this function may only be called when no TX processing 2629 * can be done concurrently, for example when queues are stopped 2630 * and the stop has been synchronized. 2631 */ 2632void ieee80211_get_key_tx_seq(struct ieee80211_key_conf *keyconf, 2633 struct ieee80211_key_seq *seq); 2634 2635/** 2636 * ieee80211_get_key_rx_seq - get key RX sequence counter 2637 * 2638 * @keyconf: the parameter passed with the set key 2639 * @tid: The TID, or -1 for the management frame value (CCMP only); 2640 * the value on TID 0 is also used for non-QoS frames. For 2641 * CMAC, only TID 0 is valid. 2642 * @seq: buffer to receive the sequence data 2643 * 2644 * This function allows a driver to retrieve the current RX IV/PNs 2645 * for the given key. It must not be called if IV checking is done 2646 * by the device and not by mac80211. 2647 * 2648 * Note that this function may only be called when no RX processing 2649 * can be done concurrently. 2650 */ 2651void ieee80211_get_key_rx_seq(struct ieee80211_key_conf *keyconf, 2652 int tid, struct ieee80211_key_seq *seq); 2653 2654/** 2655 * ieee80211_gtk_rekey_notify - notify userspace supplicant of rekeying 2656 * @vif: virtual interface the rekeying was done on 2657 * @bssid: The BSSID of the AP, for checking association 2658 * @replay_ctr: the new replay counter after GTK rekeying 2659 * @gfp: allocation flags 2660 */ 2661void ieee80211_gtk_rekey_notify(struct ieee80211_vif *vif, const u8 *bssid, 2662 const u8 *replay_ctr, gfp_t gfp); 2663 2664/** 2665 * ieee80211_wake_queue - wake specific queue 2666 * @hw: pointer as obtained from ieee80211_alloc_hw(). 2667 * @queue: queue number (counted from zero). 2668 * 2669 * Drivers should use this function instead of netif_wake_queue. 2670 */ 2671void ieee80211_wake_queue(struct ieee80211_hw *hw, int queue); 2672 2673/** 2674 * ieee80211_stop_queue - stop specific queue 2675 * @hw: pointer as obtained from ieee80211_alloc_hw(). 2676 * @queue: queue number (counted from zero). 2677 * 2678 * Drivers should use this function instead of netif_stop_queue. 2679 */ 2680void ieee80211_stop_queue(struct ieee80211_hw *hw, int queue); 2681 2682/** 2683 * ieee80211_queue_stopped - test status of the queue 2684 * @hw: pointer as obtained from ieee80211_alloc_hw(). 2685 * @queue: queue number (counted from zero). 2686 * 2687 * Drivers should use this function instead of netif_stop_queue. 2688 */ 2689 2690int ieee80211_queue_stopped(struct ieee80211_hw *hw, int queue); 2691 2692/** 2693 * ieee80211_stop_queues - stop all queues 2694 * @hw: pointer as obtained from ieee80211_alloc_hw(). 2695 * 2696 * Drivers should use this function instead of netif_stop_queue. 2697 */ 2698void ieee80211_stop_queues(struct ieee80211_hw *hw); 2699 2700/** 2701 * ieee80211_wake_queues - wake all queues 2702 * @hw: pointer as obtained from ieee80211_alloc_hw(). 2703 * 2704 * Drivers should use this function instead of netif_wake_queue. 2705 */ 2706void ieee80211_wake_queues(struct ieee80211_hw *hw); 2707 2708/** 2709 * ieee80211_scan_completed - completed hardware scan 2710 * 2711 * When hardware scan offload is used (i.e. the hw_scan() callback is 2712 * assigned) this function needs to be called by the driver to notify 2713 * mac80211 that the scan finished. This function can be called from 2714 * any context, including hardirq context. 2715 * 2716 * @hw: the hardware that finished the scan 2717 * @aborted: set to true if scan was aborted 2718 */ 2719void ieee80211_scan_completed(struct ieee80211_hw *hw, bool aborted); 2720 2721/** 2722 * ieee80211_sched_scan_results - got results from scheduled scan 2723 * 2724 * When a scheduled scan is running, this function needs to be called by the 2725 * driver whenever there are new scan results available. 2726 * 2727 * @hw: the hardware that is performing scheduled scans 2728 */ 2729void ieee80211_sched_scan_results(struct ieee80211_hw *hw); 2730 2731/** 2732 * ieee80211_sched_scan_stopped - inform that the scheduled scan has stopped 2733 * 2734 * When a scheduled scan is running, this function can be called by 2735 * the driver if it needs to stop the scan to perform another task. 2736 * Usual scenarios are drivers that cannot continue the scheduled scan 2737 * while associating, for instance. 2738 * 2739 * @hw: the hardware that is performing scheduled scans 2740 */ 2741void ieee80211_sched_scan_stopped(struct ieee80211_hw *hw); 2742 2743/** 2744 * ieee80211_iterate_active_interfaces - iterate active interfaces 2745 * 2746 * This function iterates over the interfaces associated with a given 2747 * hardware that are currently active and calls the callback for them. 2748 * This function allows the iterator function to sleep, when the iterator 2749 * function is atomic @ieee80211_iterate_active_interfaces_atomic can 2750 * be used. 2751 * Does not iterate over a new interface during add_interface() 2752 * 2753 * @hw: the hardware struct of which the interfaces should be iterated over 2754 * @iterator: the iterator function to call 2755 * @data: first argument of the iterator function 2756 */ 2757void ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw, 2758 void (*iterator)(void *data, u8 *mac, 2759 struct ieee80211_vif *vif), 2760 void *data); 2761 2762/** 2763 * ieee80211_iterate_active_interfaces_atomic - iterate active interfaces 2764 * 2765 * This function iterates over the interfaces associated with a given 2766 * hardware that are currently active and calls the callback for them. 2767 * This function requires the iterator callback function to be atomic, 2768 * if that is not desired, use @ieee80211_iterate_active_interfaces instead. 2769 * Does not iterate over a new interface during add_interface() 2770 * 2771 * @hw: the hardware struct of which the interfaces should be iterated over 2772 * @iterator: the iterator function to call, cannot sleep 2773 * @data: first argument of the iterator function 2774 */ 2775void ieee80211_iterate_active_interfaces_atomic(struct ieee80211_hw *hw, 2776 void (*iterator)(void *data, 2777 u8 *mac, 2778 struct ieee80211_vif *vif), 2779 void *data); 2780 2781/** 2782 * ieee80211_queue_work - add work onto the mac80211 workqueue 2783 * 2784 * Drivers and mac80211 use this to add work onto the mac80211 workqueue. 2785 * This helper ensures drivers are not queueing work when they should not be. 2786 * 2787 * @hw: the hardware struct for the interface we are adding work for 2788 * @work: the work we want to add onto the mac80211 workqueue 2789 */ 2790void ieee80211_queue_work(struct ieee80211_hw *hw, struct work_struct *work); 2791 2792/** 2793 * ieee80211_queue_delayed_work - add work onto the mac80211 workqueue 2794 * 2795 * Drivers and mac80211 use this to queue delayed work onto the mac80211 2796 * workqueue. 2797 * 2798 * @hw: the hardware struct for the interface we are adding work for 2799 * @dwork: delayable work to queue onto the mac80211 workqueue 2800 * @delay: number of jiffies to wait before queueing 2801 */ 2802void ieee80211_queue_delayed_work(struct ieee80211_hw *hw, 2803 struct delayed_work *dwork, 2804 unsigned long delay); 2805 2806/** 2807 * ieee80211_start_tx_ba_session - Start a tx Block Ack session. 2808 * @sta: the station for which to start a BA session 2809 * @tid: the TID to BA on. 2810 * @timeout: session timeout value (in TUs) 2811 * 2812 * Return: success if addBA request was sent, failure otherwise 2813 * 2814 * Although mac80211/low level driver/user space application can estimate 2815 * the need to start aggregation on a certain RA/TID, the session level 2816 * will be managed by the mac80211. 2817 */ 2818int ieee80211_start_tx_ba_session(struct ieee80211_sta *sta, u16 tid, 2819 u16 timeout); 2820 2821/** 2822 * ieee80211_start_tx_ba_cb_irqsafe - low level driver ready to aggregate. 2823 * @vif: &struct ieee80211_vif pointer from the add_interface callback 2824 * @ra: receiver address of the BA session recipient. 2825 * @tid: the TID to BA on. 2826 * 2827 * This function must be called by low level driver once it has 2828 * finished with preparations for the BA session. It can be called 2829 * from any context. 2830 */ 2831void ieee80211_start_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra, 2832 u16 tid); 2833 2834/** 2835 * ieee80211_stop_tx_ba_session - Stop a Block Ack session. 2836 * @sta: the station whose BA session to stop 2837 * @tid: the TID to stop BA. 2838 * 2839 * Return: negative error if the TID is invalid, or no aggregation active 2840 * 2841 * Although mac80211/low level driver/user space application can estimate 2842 * the need to stop aggregation on a certain RA/TID, the session level 2843 * will be managed by the mac80211. 2844 */ 2845int ieee80211_stop_tx_ba_session(struct ieee80211_sta *sta, u16 tid); 2846 2847/** 2848 * ieee80211_stop_tx_ba_cb_irqsafe - low level driver ready to stop aggregate. 2849 * @vif: &struct ieee80211_vif pointer from the add_interface callback 2850 * @ra: receiver address of the BA session recipient. 2851 * @tid: the desired TID to BA on. 2852 * 2853 * This function must be called by low level driver once it has 2854 * finished with preparations for the BA session tear down. It 2855 * can be called from any context. 2856 */ 2857void ieee80211_stop_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra, 2858 u16 tid); 2859 2860/** 2861 * ieee80211_find_sta - find a station 2862 * 2863 * @vif: virtual interface to look for station on 2864 * @addr: station's address 2865 * 2866 * This function must be called under RCU lock and the 2867 * resulting pointer is only valid under RCU lock as well. 2868 */ 2869struct ieee80211_sta *ieee80211_find_sta(struct ieee80211_vif *vif, 2870 const u8 *addr); 2871 2872/** 2873 * ieee80211_find_sta_by_ifaddr - find a station on hardware 2874 * 2875 * @hw: pointer as obtained from ieee80211_alloc_hw() 2876 * @addr: remote station's address 2877 * @localaddr: local address (vif->sdata->vif.addr). Use NULL for 'any'. 2878 * 2879 * This function must be called under RCU lock and the 2880 * resulting pointer is only valid under RCU lock as well. 2881 * 2882 * NOTE: You may pass NULL for localaddr, but then you will just get 2883 * the first STA that matches the remote address 'addr'. 2884 * We can have multiple STA associated with multiple 2885 * logical stations (e.g. consider a station connecting to another 2886 * BSSID on the same AP hardware without disconnecting first). 2887 * In this case, the result of this method with localaddr NULL 2888 * is not reliable. 2889 * 2890 * DO NOT USE THIS FUNCTION with localaddr NULL if at all possible. 2891 */ 2892struct ieee80211_sta *ieee80211_find_sta_by_ifaddr(struct ieee80211_hw *hw, 2893 const u8 *addr, 2894 const u8 *localaddr); 2895 2896/** 2897 * ieee80211_sta_block_awake - block station from waking up 2898 * @hw: the hardware 2899 * @pubsta: the station 2900 * @block: whether to block or unblock 2901 * 2902 * Some devices require that all frames that are on the queues 2903 * for a specific station that went to sleep are flushed before 2904 * a poll response or frames after the station woke up can be 2905 * delivered to that it. Note that such frames must be rejected 2906 * by the driver as filtered, with the appropriate status flag. 2907 * 2908 * This function allows implementing this mode in a race-free 2909 * manner. 2910 * 2911 * To do this, a driver must keep track of the number of frames 2912 * still enqueued for a specific station. If this number is not 2913 * zero when the station goes to sleep, the driver must call 2914 * this function to force mac80211 to consider the station to 2915 * be asleep regardless of the station's actual state. Once the 2916 * number of outstanding frames reaches zero, the driver must 2917 * call this function again to unblock the station. That will 2918 * cause mac80211 to be able to send ps-poll responses, and if 2919 * the station queried in the meantime then frames will also 2920 * be sent out as a result of this. Additionally, the driver 2921 * will be notified that the station woke up some time after 2922 * it is unblocked, regardless of whether the station actually 2923 * woke up while blocked or not. 2924 */ 2925void ieee80211_sta_block_awake(struct ieee80211_hw *hw, 2926 struct ieee80211_sta *pubsta, bool block); 2927 2928/** 2929 * ieee80211_iter_keys - iterate keys programmed into the device 2930 * @hw: pointer obtained from ieee80211_alloc_hw() 2931 * @vif: virtual interface to iterate, may be %NULL for all 2932 * @iter: iterator function that will be called for each key 2933 * @iter_data: custom data to pass to the iterator function 2934 * 2935 * This function can be used to iterate all the keys known to 2936 * mac80211, even those that weren't previously programmed into 2937 * the device. This is intended for use in WoWLAN if the device 2938 * needs reprogramming of the keys during suspend. Note that due 2939 * to locking reasons, it is also only safe to call this at few 2940 * spots since it must hold the RTNL and be able to sleep. 2941 */ 2942void ieee80211_iter_keys(struct ieee80211_hw *hw, 2943 struct ieee80211_vif *vif, 2944 void (*iter)(struct ieee80211_hw *hw, 2945 struct ieee80211_vif *vif, 2946 struct ieee80211_sta *sta, 2947 struct ieee80211_key_conf *key, 2948 void *data), 2949 void *iter_data); 2950 2951/** 2952 * ieee80211_ap_probereq_get - retrieve a Probe Request template 2953 * @hw: pointer obtained from ieee80211_alloc_hw(). 2954 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 2955 * 2956 * Creates a Probe Request template which can, for example, be uploaded to 2957 * hardware. The template is filled with bssid, ssid and supported rate 2958 * information. This function must only be called from within the 2959 * .bss_info_changed callback function and only in managed mode. The function 2960 * is only useful when the interface is associated, otherwise it will return 2961 * NULL. 2962 */ 2963struct sk_buff *ieee80211_ap_probereq_get(struct ieee80211_hw *hw, 2964 struct ieee80211_vif *vif); 2965 2966/** 2967 * ieee80211_beacon_loss - inform hardware does not receive beacons 2968 * 2969 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 2970 * 2971 * When beacon filtering is enabled with %IEEE80211_HW_BEACON_FILTER and 2972 * %IEEE80211_CONF_PS is set, the driver needs to inform whenever the 2973 * hardware is not receiving beacons with this function. 2974 */ 2975void ieee80211_beacon_loss(struct ieee80211_vif *vif); 2976 2977/** 2978 * ieee80211_connection_loss - inform hardware has lost connection to the AP 2979 * 2980 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 2981 * 2982 * When beacon filtering is enabled with %IEEE80211_HW_BEACON_FILTER, and 2983 * %IEEE80211_CONF_PS and %IEEE80211_HW_CONNECTION_MONITOR are set, the driver 2984 * needs to inform if the connection to the AP has been lost. 2985 * 2986 * This function will cause immediate change to disassociated state, 2987 * without connection recovery attempts. 2988 */ 2989void ieee80211_connection_loss(struct ieee80211_vif *vif); 2990 2991/** 2992 * ieee80211_disable_dyn_ps - force mac80211 to temporarily disable dynamic psm 2993 * 2994 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 2995 * 2996 * Some hardware require full power save to manage simultaneous BT traffic 2997 * on the WLAN frequency. Full PSM is required periodically, whenever there are 2998 * burst of BT traffic. The hardware gets information of BT traffic via 2999 * hardware co-existence lines, and consequentially requests mac80211 to 3000 * (temporarily) enter full psm. 3001 * This function will only temporarily disable dynamic PS, not enable PSM if 3002 * it was not already enabled. 3003 * The driver must make sure to re-enable dynamic PS using 3004 * ieee80211_enable_dyn_ps() if the driver has disabled it. 3005 * 3006 */ 3007void ieee80211_disable_dyn_ps(struct ieee80211_vif *vif); 3008 3009/** 3010 * ieee80211_enable_dyn_ps - restore dynamic psm after being disabled 3011 * 3012 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 3013 * 3014 * This function restores dynamic PS after being temporarily disabled via 3015 * ieee80211_disable_dyn_ps(). Each ieee80211_disable_dyn_ps() call must 3016 * be coupled with an eventual call to this function. 3017 * 3018 */ 3019void ieee80211_enable_dyn_ps(struct ieee80211_vif *vif); 3020 3021/** 3022 * ieee80211_cqm_rssi_notify - inform a configured connection quality monitoring 3023 * rssi threshold triggered 3024 * 3025 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 3026 * @rssi_event: the RSSI trigger event type 3027 * @gfp: context flags 3028 * 3029 * When the %IEEE80211_HW_SUPPORTS_CQM_RSSI is set, and a connection quality 3030 * monitoring is configured with an rssi threshold, the driver will inform 3031 * whenever the rssi level reaches the threshold. 3032 */ 3033void ieee80211_cqm_rssi_notify(struct ieee80211_vif *vif, 3034 enum nl80211_cqm_rssi_threshold_event rssi_event, 3035 gfp_t gfp); 3036 3037/** 3038 * ieee80211_get_operstate - get the operstate of the vif 3039 * 3040 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 3041 * 3042 * The driver might need to know the operstate of the net_device 3043 * (specifically, whether the link is IF_OPER_UP after resume) 3044 */ 3045unsigned char ieee80211_get_operstate(struct ieee80211_vif *vif); 3046 3047/** 3048 * ieee80211_chswitch_done - Complete channel switch process 3049 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 3050 * @success: make the channel switch successful or not 3051 * 3052 * Complete the channel switch post-process: set the new operational channel 3053 * and wake up the suspended queues. 3054 */ 3055void ieee80211_chswitch_done(struct ieee80211_vif *vif, bool success); 3056 3057/** 3058 * ieee80211_request_smps - request SM PS transition 3059 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 3060 * @smps_mode: new SM PS mode 3061 * 3062 * This allows the driver to request an SM PS transition in managed 3063 * mode. This is useful when the driver has more information than 3064 * the stack about possible interference, for example by bluetooth. 3065 */ 3066void ieee80211_request_smps(struct ieee80211_vif *vif, 3067 enum ieee80211_smps_mode smps_mode); 3068 3069/** 3070 * ieee80211_key_removed - disable hw acceleration for key 3071 * @key_conf: The key hw acceleration should be disabled for 3072 * 3073 * This allows drivers to indicate that the given key has been 3074 * removed from hardware acceleration, due to a new key that 3075 * was added. Don't use this if the key can continue to be used 3076 * for TX, if the key restriction is on RX only it is permitted 3077 * to keep the key for TX only and not call this function. 3078 * 3079 * Due to locking constraints, it may only be called during 3080 * @set_key. This function must be allowed to sleep, and the 3081 * key it tries to disable may still be used until it returns. 3082 */ 3083void ieee80211_key_removed(struct ieee80211_key_conf *key_conf); 3084 3085/** 3086 * ieee80211_ready_on_channel - notification of remain-on-channel start 3087 * @hw: pointer as obtained from ieee80211_alloc_hw() 3088 */ 3089void ieee80211_ready_on_channel(struct ieee80211_hw *hw); 3090 3091/** 3092 * ieee80211_remain_on_channel_expired - remain_on_channel duration expired 3093 * @hw: pointer as obtained from ieee80211_alloc_hw() 3094 */ 3095void ieee80211_remain_on_channel_expired(struct ieee80211_hw *hw); 3096 3097/** 3098 * ieee80211_stop_rx_ba_session - callback to stop existing BA sessions 3099 * 3100 * in order not to harm the system performance and user experience, the device 3101 * may request not to allow any rx ba session and tear down existing rx ba 3102 * sessions based on system constraints such as periodic BT activity that needs 3103 * to limit wlan activity (eg.sco or a2dp)." 3104 * in such cases, the intention is to limit the duration of the rx ppdu and 3105 * therefore prevent the peer device to use a-mpdu aggregation. 3106 * 3107 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 3108 * @ba_rx_bitmap: Bit map of open rx ba per tid 3109 * @addr: & to bssid mac address 3110 */ 3111void ieee80211_stop_rx_ba_session(struct ieee80211_vif *vif, u16 ba_rx_bitmap, 3112 const u8 *addr); 3113 3114/* Rate control API */ 3115 3116/** 3117 * enum rate_control_changed - flags to indicate which parameter changed 3118 * 3119 * @IEEE80211_RC_HT_CHANGED: The HT parameters of the operating channel have 3120 * changed, rate control algorithm can update its internal state if needed. 3121 */ 3122enum rate_control_changed { 3123 IEEE80211_RC_HT_CHANGED = BIT(0) 3124}; 3125 3126/** 3127 * struct ieee80211_tx_rate_control - rate control information for/from RC algo 3128 * 3129 * @hw: The hardware the algorithm is invoked for. 3130 * @sband: The band this frame is being transmitted on. 3131 * @bss_conf: the current BSS configuration 3132 * @reported_rate: The rate control algorithm can fill this in to indicate 3133 * which rate should be reported to userspace as the current rate and 3134 * used for rate calculations in the mesh network. 3135 * @rts: whether RTS will be used for this frame because it is longer than the 3136 * RTS threshold 3137 * @short_preamble: whether mac80211 will request short-preamble transmission 3138 * if the selected rate supports it 3139 * @max_rate_idx: user-requested maximum rate (not MCS for now) 3140 * (deprecated; this will be removed once drivers get updated to use 3141 * rate_idx_mask) 3142 * @rate_idx_mask: user-requested rate mask (not MCS for now) 3143 * @skb: the skb that will be transmitted, the control information in it needs 3144 * to be filled in 3145 * @bss: whether this frame is sent out in AP or IBSS mode 3146 */ 3147struct ieee80211_tx_rate_control { 3148 struct ieee80211_hw *hw; 3149 struct ieee80211_supported_band *sband; 3150 struct ieee80211_bss_conf *bss_conf; 3151 struct sk_buff *skb; 3152 struct ieee80211_tx_rate reported_rate; 3153 bool rts, short_preamble; 3154 u8 max_rate_idx; 3155 u32 rate_idx_mask; 3156 bool bss; 3157}; 3158 3159struct rate_control_ops { 3160 struct module *module; 3161 const char *name; 3162 void *(*alloc)(struct ieee80211_hw *hw, struct dentry *debugfsdir); 3163 void (*free)(void *priv); 3164 3165 void *(*alloc_sta)(void *priv, struct ieee80211_sta *sta, gfp_t gfp); 3166 void (*rate_init)(void *priv, struct ieee80211_supported_band *sband, 3167 struct ieee80211_sta *sta, void *priv_sta); 3168 void (*rate_update)(void *priv, struct ieee80211_supported_band *sband, 3169 struct ieee80211_sta *sta, 3170 void *priv_sta, u32 changed, 3171 enum nl80211_channel_type oper_chan_type); 3172 void (*free_sta)(void *priv, struct ieee80211_sta *sta, 3173 void *priv_sta); 3174 3175 void (*tx_status)(void *priv, struct ieee80211_supported_band *sband, 3176 struct ieee80211_sta *sta, void *priv_sta, 3177 struct sk_buff *skb); 3178 void (*get_rate)(void *priv, struct ieee80211_sta *sta, void *priv_sta, 3179 struct ieee80211_tx_rate_control *txrc); 3180 3181 void (*add_sta_debugfs)(void *priv, void *priv_sta, 3182 struct dentry *dir); 3183 void (*remove_sta_debugfs)(void *priv, void *priv_sta); 3184}; 3185 3186static inline int rate_supported(struct ieee80211_sta *sta, 3187 enum ieee80211_band band, 3188 int index) 3189{ 3190 return (sta == NULL || sta->supp_rates[band] & BIT(index)); 3191} 3192 3193/** 3194 * rate_control_send_low - helper for drivers for management/no-ack frames 3195 * 3196 * Rate control algorithms that agree to use the lowest rate to 3197 * send management frames and NO_ACK data with the respective hw 3198 * retries should use this in the beginning of their mac80211 get_rate 3199 * callback. If true is returned the rate control can simply return. 3200 * If false is returned we guarantee that sta and sta and priv_sta is 3201 * not null. 3202 * 3203 * Rate control algorithms wishing to do more intelligent selection of 3204 * rate for multicast/broadcast frames may choose to not use this. 3205 * 3206 * @sta: &struct ieee80211_sta pointer to the target destination. Note 3207 * that this may be null. 3208 * @priv_sta: private rate control structure. This may be null. 3209 * @txrc: rate control information we sholud populate for mac80211. 3210 */ 3211bool rate_control_send_low(struct ieee80211_sta *sta, 3212 void *priv_sta, 3213 struct ieee80211_tx_rate_control *txrc); 3214 3215 3216static inline s8 3217rate_lowest_index(struct ieee80211_supported_band *sband, 3218 struct ieee80211_sta *sta) 3219{ 3220 int i; 3221 3222 for (i = 0; i < sband->n_bitrates; i++) 3223 if (rate_supported(sta, sband->band, i)) 3224 return i; 3225 3226 /* warn when we cannot find a rate. */ 3227 WARN_ON(1); 3228 3229 return 0; 3230} 3231 3232static inline 3233bool rate_usable_index_exists(struct ieee80211_supported_band *sband, 3234 struct ieee80211_sta *sta) 3235{ 3236 unsigned int i; 3237 3238 for (i = 0; i < sband->n_bitrates; i++) 3239 if (rate_supported(sta, sband->band, i)) 3240 return true; 3241 return false; 3242} 3243 3244int ieee80211_rate_control_register(struct rate_control_ops *ops); 3245void ieee80211_rate_control_unregister(struct rate_control_ops *ops); 3246 3247static inline bool 3248conf_is_ht20(struct ieee80211_conf *conf) 3249{ 3250 return conf->channel_type == NL80211_CHAN_HT20; 3251} 3252 3253static inline bool 3254conf_is_ht40_minus(struct ieee80211_conf *conf) 3255{ 3256 return conf->channel_type == NL80211_CHAN_HT40MINUS; 3257} 3258 3259static inline bool 3260conf_is_ht40_plus(struct ieee80211_conf *conf) 3261{ 3262 return conf->channel_type == NL80211_CHAN_HT40PLUS; 3263} 3264 3265static inline bool 3266conf_is_ht40(struct ieee80211_conf *conf) 3267{ 3268 return conf_is_ht40_minus(conf) || conf_is_ht40_plus(conf); 3269} 3270 3271static inline bool 3272conf_is_ht(struct ieee80211_conf *conf) 3273{ 3274 return conf->channel_type != NL80211_CHAN_NO_HT; 3275} 3276 3277static inline enum nl80211_iftype 3278ieee80211_iftype_p2p(enum nl80211_iftype type, bool p2p) 3279{ 3280 if (p2p) { 3281 switch (type) { 3282 case NL80211_IFTYPE_STATION: 3283 return NL80211_IFTYPE_P2P_CLIENT; 3284 case NL80211_IFTYPE_AP: 3285 return NL80211_IFTYPE_P2P_GO; 3286 default: 3287 break; 3288 } 3289 } 3290 return type; 3291} 3292 3293static inline enum nl80211_iftype 3294ieee80211_vif_type_p2p(struct ieee80211_vif *vif) 3295{ 3296 return ieee80211_iftype_p2p(vif->type, vif->p2p); 3297} 3298 3299#endif /* MAC80211_H */ 3300