mac80211.h revision e039fa4a4195ac4ee895e6f3d1334beed63256fe
1/* 2 * mac80211 <-> driver interface 3 * 4 * Copyright 2002-2005, Devicescape Software, Inc. 5 * Copyright 2006-2007 Jiri Benc <jbenc@suse.cz> 6 * Copyright 2007 Johannes Berg <johannes@sipsolutions.net> 7 * 8 * This program is free software; you can redistribute it and/or modify 9 * it under the terms of the GNU General Public License version 2 as 10 * published by the Free Software Foundation. 11 */ 12 13#ifndef MAC80211_H 14#define MAC80211_H 15 16#include <linux/kernel.h> 17#include <linux/if_ether.h> 18#include <linux/skbuff.h> 19#include <linux/wireless.h> 20#include <linux/device.h> 21#include <linux/ieee80211.h> 22#include <net/wireless.h> 23#include <net/cfg80211.h> 24 25/** 26 * DOC: Introduction 27 * 28 * mac80211 is the Linux stack for 802.11 hardware that implements 29 * only partial functionality in hard- or firmware. This document 30 * defines the interface between mac80211 and low-level hardware 31 * drivers. 32 */ 33 34/** 35 * DOC: Calling mac80211 from interrupts 36 * 37 * Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be 38 * called in hardware interrupt context. The low-level driver must not call any 39 * other functions in hardware interrupt context. If there is a need for such 40 * call, the low-level driver should first ACK the interrupt and perform the 41 * IEEE 802.11 code call after this, e.g. from a scheduled workqueue or even 42 * tasklet function. 43 * 44 * NOTE: If the driver opts to use the _irqsafe() functions, it may not also 45 * use the non-irqsafe functions! 46 */ 47 48/** 49 * DOC: Warning 50 * 51 * If you're reading this document and not the header file itself, it will 52 * be incomplete because not all documentation has been converted yet. 53 */ 54 55/** 56 * DOC: Frame format 57 * 58 * As a general rule, when frames are passed between mac80211 and the driver, 59 * they start with the IEEE 802.11 header and include the same octets that are 60 * sent over the air except for the FCS which should be calculated by the 61 * hardware. 62 * 63 * There are, however, various exceptions to this rule for advanced features: 64 * 65 * The first exception is for hardware encryption and decryption offload 66 * where the IV/ICV may or may not be generated in hardware. 67 * 68 * Secondly, when the hardware handles fragmentation, the frame handed to 69 * the driver from mac80211 is the MSDU, not the MPDU. 70 * 71 * Finally, for received frames, the driver is able to indicate that it has 72 * filled a radiotap header and put that in front of the frame; if it does 73 * not do so then mac80211 may add this under certain circumstances. 74 */ 75 76/** 77 * enum ieee80211_notification_type - Low level driver notification 78 * @IEEE80211_NOTIFY_RE_ASSOC: start the re-association sequence 79 */ 80enum ieee80211_notification_types { 81 IEEE80211_NOTIFY_RE_ASSOC, 82}; 83 84/** 85 * struct ieee80211_ht_bss_info - describing BSS's HT characteristics 86 * 87 * This structure describes most essential parameters needed 88 * to describe 802.11n HT characteristics in a BSS 89 * 90 * @primary_channel: channel number of primery channel 91 * @bss_cap: 802.11n's general BSS capabilities (e.g. channel width) 92 * @bss_op_mode: 802.11n's BSS operation modes (e.g. HT protection) 93 */ 94struct ieee80211_ht_bss_info { 95 u8 primary_channel; 96 u8 bss_cap; /* use IEEE80211_HT_IE_CHA_ */ 97 u8 bss_op_mode; /* use IEEE80211_HT_IE_ */ 98}; 99 100/** 101 * enum ieee80211_max_queues - maximum number of queues 102 * 103 * @IEEE80211_MAX_QUEUES: Maximum number of regular device queues. 104 * @IEEE80211_MAX_AMPDU_QUEUES: Maximum number of queues usable 105 * for A-MPDU operation. 106 */ 107enum ieee80211_max_queues { 108 IEEE80211_MAX_QUEUES = 16, 109 IEEE80211_MAX_AMPDU_QUEUES = 16, 110}; 111 112/** 113 * struct ieee80211_tx_queue_params - transmit queue configuration 114 * 115 * The information provided in this structure is required for QoS 116 * transmit queue configuration. Cf. IEEE 802.11 7.3.2.29. 117 * 118 * @aifs: arbitration interface space [0..255, -1: use default] 119 * @cw_min: minimum contention window [will be a value of the form 120 * 2^n-1 in the range 1..1023; 0: use default] 121 * @cw_max: maximum contention window [like @cw_min] 122 * @txop: maximum burst time in units of 32 usecs, 0 meaning disabled 123 */ 124struct ieee80211_tx_queue_params { 125 s16 aifs; 126 u16 cw_min; 127 u16 cw_max; 128 u16 txop; 129}; 130 131/** 132 * struct ieee80211_tx_queue_stats - transmit queue statistics 133 * 134 * @len: number of packets in queue 135 * @limit: queue length limit 136 * @count: number of frames sent 137 */ 138struct ieee80211_tx_queue_stats { 139 unsigned int len; 140 unsigned int limit; 141 unsigned int count; 142}; 143 144struct ieee80211_low_level_stats { 145 unsigned int dot11ACKFailureCount; 146 unsigned int dot11RTSFailureCount; 147 unsigned int dot11FCSErrorCount; 148 unsigned int dot11RTSSuccessCount; 149}; 150 151/** 152 * enum ieee80211_bss_change - BSS change notification flags 153 * 154 * These flags are used with the bss_info_changed() callback 155 * to indicate which BSS parameter changed. 156 * 157 * @BSS_CHANGED_ASSOC: association status changed (associated/disassociated), 158 * also implies a change in the AID. 159 * @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed 160 * @BSS_CHANGED_ERP_PREAMBLE: preamble changed 161 * @BSS_CHANGED_HT: 802.11n parameters changed 162 */ 163enum ieee80211_bss_change { 164 BSS_CHANGED_ASSOC = 1<<0, 165 BSS_CHANGED_ERP_CTS_PROT = 1<<1, 166 BSS_CHANGED_ERP_PREAMBLE = 1<<2, 167 BSS_CHANGED_HT = 1<<4, 168}; 169 170/** 171 * struct ieee80211_bss_conf - holds the BSS's changing parameters 172 * 173 * This structure keeps information about a BSS (and an association 174 * to that BSS) that can change during the lifetime of the BSS. 175 * 176 * @assoc: association status 177 * @aid: association ID number, valid only when @assoc is true 178 * @use_cts_prot: use CTS protection 179 * @use_short_preamble: use 802.11b short preamble 180 * @timestamp: beacon timestamp 181 * @beacon_int: beacon interval 182 * @assoc_capability: capabbilities taken from assoc resp 183 * @assoc_ht: association in HT mode 184 * @ht_conf: ht capabilities 185 * @ht_bss_conf: ht extended capabilities 186 */ 187struct ieee80211_bss_conf { 188 /* association related data */ 189 bool assoc; 190 u16 aid; 191 /* erp related data */ 192 bool use_cts_prot; 193 bool use_short_preamble; 194 u16 beacon_int; 195 u16 assoc_capability; 196 u64 timestamp; 197 /* ht related data */ 198 bool assoc_ht; 199 struct ieee80211_ht_info *ht_conf; 200 struct ieee80211_ht_bss_info *ht_bss_conf; 201}; 202 203/** 204 * enum mac80211_tx_flags - flags to transmission information/status 205 * 206 * These flags are used with the @flags member of &ieee80211_tx_info 207 * 208 * @IEEE80211_TX_CTL_REQ_TX_STATUS: request TX status callback for this frame. 209 * @IEEE80211_TX_CTL_DO_NOT_ENCRYPT: send this frame without encryption; 210 * e.g., for EAPOL frame 211 * @IEEE80211_TX_CTL_USE_RTS_CTS: use RTS-CTS before sending frame 212 * @IEEE80211_TX_CTL_USE_CTS_PROTECT: use CTS protection for the frame (e.g., 213 * for combined 802.11g / 802.11b networks) 214 * @IEEE80211_TX_CTL_NO_ACK: tell the low level not to wait for an ack 215 * @IEEE80211_TX_CTL_RATE_CTRL_PROBE 216 * @IEEE80211_TX_CTL_CLEAR_PS_FILT: clear powersave filter for destination 217 * station 218 * @IEEE80211_TX_CTL_REQUEUE: 219 * @IEEE80211_TX_CTL_FIRST_FRAGMENT: this is a first fragment of the frame 220 * @IEEE80211_TX_CTL_LONG_RETRY_LIMIT: this frame should be send using the 221 * through set_retry_limit configured long retry value 222 * @IEEE80211_TX_CTL_EAPOL_FRAME: internal to mac80211 223 * @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon 224 * @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU 225 * @IEEE80211_TX_CTL_OFDM_HT: this frame can be sent in HT OFDM rates. number 226 * of streams when this flag is on can be extracted from antenna_sel_tx, 227 * so if 1 antenna is marked use SISO, 2 antennas marked use MIMO, n 228 * antennas marked use MIMO_n. 229 * @IEEE80211_TX_CTL_GREEN_FIELD: use green field protection for this frame 230 * @IEEE80211_TX_CTL_40_MHZ_WIDTH: send this frame using 40 Mhz channel width 231 * @IEEE80211_TX_CTL_DUP_DATA: duplicate data frame on both 20 Mhz channels 232 * @IEEE80211_TX_CTL_SHORT_GI: send this frame using short guard interval 233 * @IEEE80211_TX_STAT_TX_FILTERED: The frame was not transmitted 234 * because the destination STA was in powersave mode. 235 * @IEEE80211_TX_STAT_ACK: Frame was acknowledged 236 * @IEEE80211_TX_STAT_AMPDU: The frame was aggregated, so status 237 * is for the whole aggregation. 238 */ 239enum mac80211_tx_control_flags { 240 IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0), 241 IEEE80211_TX_CTL_DO_NOT_ENCRYPT = BIT(1), 242 IEEE80211_TX_CTL_USE_RTS_CTS = BIT(2), 243 IEEE80211_TX_CTL_USE_CTS_PROTECT = BIT(3), 244 IEEE80211_TX_CTL_NO_ACK = BIT(4), 245 IEEE80211_TX_CTL_RATE_CTRL_PROBE = BIT(5), 246 IEEE80211_TX_CTL_CLEAR_PS_FILT = BIT(6), 247 IEEE80211_TX_CTL_REQUEUE = BIT(7), 248 IEEE80211_TX_CTL_FIRST_FRAGMENT = BIT(8), 249 IEEE80211_TX_CTL_SHORT_PREAMBLE = BIT(9), 250 IEEE80211_TX_CTL_LONG_RETRY_LIMIT = BIT(10), 251 IEEE80211_TX_CTL_EAPOL_FRAME = BIT(11), 252 IEEE80211_TX_CTL_SEND_AFTER_DTIM = BIT(12), 253 IEEE80211_TX_CTL_AMPDU = BIT(13), 254 IEEE80211_TX_CTL_OFDM_HT = BIT(14), 255 IEEE80211_TX_CTL_GREEN_FIELD = BIT(15), 256 IEEE80211_TX_CTL_40_MHZ_WIDTH = BIT(16), 257 IEEE80211_TX_CTL_DUP_DATA = BIT(17), 258 IEEE80211_TX_CTL_SHORT_GI = BIT(18), 259 IEEE80211_TX_CTL_INJECTED = BIT(19), 260 IEEE80211_TX_STAT_TX_FILTERED = BIT(20), 261 IEEE80211_TX_STAT_ACK = BIT(21), 262 IEEE80211_TX_STAT_AMPDU = BIT(22), 263}; 264 265 266#define IEEE80211_TX_INFO_DRIVER_DATA_SIZE \ 267 (sizeof(((struct sk_buff *)0)->cb) - 8) 268#define IEEE80211_TX_INFO_DRIVER_DATA_PTRS \ 269 (IEEE80211_TX_INFO_DRIVER_DATA_SIZE / sizeof(void *)) 270 271/** 272 * struct ieee80211_tx_info - skb transmit information 273 * 274 * This structure is placed in skb->cb for three uses: 275 * (1) mac80211 TX control - mac80211 tells the driver what to do 276 * (2) driver internal use (if applicable) 277 * (3) TX status information - driver tells mac80211 what happened 278 * 279 * @flags: transmit info flags, defined above 280 * @retry_count: number of retries 281 * @excessive_retries: set to 1 if the frame was retried many times 282 * but not acknowledged 283 * @ampdu_ack_len: number of aggregated frames. 284 * relevant only if IEEE80211_TX_STATUS_AMPDU was set. 285 * @ampdu_ack_map: block ack bit map for the aggregation. 286 * relevant only if IEEE80211_TX_STATUS_AMPDU was set. 287 * @ack_signal: signal strength of the ACK frame 288 */ 289struct ieee80211_tx_info { 290 /* common information */ 291 u32 flags; 292 u8 band; 293 s8 tx_rate_idx; 294 u8 antenna_sel_tx; 295 296 u8 queue; /* use skb_queue_mapping soon */ 297 298 union { 299 struct { 300 struct ieee80211_vif *vif; 301 struct ieee80211_key_conf *hw_key; 302 unsigned long jiffies; 303 int ifindex; 304 u16 aid; 305 s8 rts_cts_rate_idx, alt_retry_rate_idx; 306 u8 retry_limit; 307 u8 icv_len; 308 u8 iv_len; 309 } control; 310 struct { 311 u64 ampdu_ack_map; 312 int ack_signal; 313 u8 retry_count; 314 bool excessive_retries; 315 u8 ampdu_ack_len; 316 } status; 317 void *driver_data[IEEE80211_TX_INFO_DRIVER_DATA_PTRS]; 318 }; 319}; 320 321static inline struct ieee80211_tx_info *IEEE80211_SKB_CB(struct sk_buff *skb) 322{ 323 return (struct ieee80211_tx_info *)skb->cb; 324} 325 326 327/** 328 * enum mac80211_rx_flags - receive flags 329 * 330 * These flags are used with the @flag member of &struct ieee80211_rx_status. 331 * @RX_FLAG_MMIC_ERROR: Michael MIC error was reported on this frame. 332 * Use together with %RX_FLAG_MMIC_STRIPPED. 333 * @RX_FLAG_DECRYPTED: This frame was decrypted in hardware. 334 * @RX_FLAG_RADIOTAP: This frame starts with a radiotap header. 335 * @RX_FLAG_MMIC_STRIPPED: the Michael MIC is stripped off this frame, 336 * verification has been done by the hardware. 337 * @RX_FLAG_IV_STRIPPED: The IV/ICV are stripped from this frame. 338 * If this flag is set, the stack cannot do any replay detection 339 * hence the driver or hardware will have to do that. 340 * @RX_FLAG_FAILED_FCS_CRC: Set this flag if the FCS check failed on 341 * the frame. 342 * @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on 343 * the frame. 344 * @RX_FLAG_TSFT: The timestamp passed in the RX status (@mactime field) 345 * is valid. This is useful in monitor mode and necessary for beacon frames 346 * to enable IBSS merging. 347 */ 348enum mac80211_rx_flags { 349 RX_FLAG_MMIC_ERROR = 1<<0, 350 RX_FLAG_DECRYPTED = 1<<1, 351 RX_FLAG_RADIOTAP = 1<<2, 352 RX_FLAG_MMIC_STRIPPED = 1<<3, 353 RX_FLAG_IV_STRIPPED = 1<<4, 354 RX_FLAG_FAILED_FCS_CRC = 1<<5, 355 RX_FLAG_FAILED_PLCP_CRC = 1<<6, 356 RX_FLAG_TSFT = 1<<7, 357}; 358 359/** 360 * struct ieee80211_rx_status - receive status 361 * 362 * The low-level driver should provide this information (the subset 363 * supported by hardware) to the 802.11 code with each received 364 * frame. 365 * 366 * @mactime: value in microseconds of the 64-bit Time Synchronization Function 367 * (TSF) timer when the first data symbol (MPDU) arrived at the hardware. 368 * @band: the active band when this frame was received 369 * @freq: frequency the radio was tuned to when receiving this frame, in MHz 370 * @signal: signal strength when receiving this frame, either in dBm, in dB or 371 * unspecified depending on the hardware capabilities flags 372 * @IEEE80211_HW_SIGNAL_* 373 * @noise: noise when receiving this frame, in dBm. 374 * @qual: overall signal quality indication, in percent (0-100). 375 * @antenna: antenna used 376 * @rate_idx: index of data rate into band's supported rates 377 * @flag: %RX_FLAG_* 378 */ 379struct ieee80211_rx_status { 380 u64 mactime; 381 enum ieee80211_band band; 382 int freq; 383 int signal; 384 int noise; 385 int qual; 386 int antenna; 387 int rate_idx; 388 int flag; 389}; 390 391/** 392 * enum ieee80211_conf_flags - configuration flags 393 * 394 * Flags to define PHY configuration options 395 * 396 * @IEEE80211_CONF_SHORT_SLOT_TIME: use 802.11g short slot time 397 * @IEEE80211_CONF_RADIOTAP: add radiotap header at receive time (if supported) 398 * @IEEE80211_CONF_SUPPORT_HT_MODE: use 802.11n HT capabilities (if supported) 399 */ 400enum ieee80211_conf_flags { 401 IEEE80211_CONF_SHORT_SLOT_TIME = (1<<0), 402 IEEE80211_CONF_RADIOTAP = (1<<1), 403 IEEE80211_CONF_SUPPORT_HT_MODE = (1<<2), 404}; 405 406/** 407 * struct ieee80211_conf - configuration of the device 408 * 409 * This struct indicates how the driver shall configure the hardware. 410 * 411 * @radio_enabled: when zero, driver is required to switch off the radio. 412 * TODO make a flag 413 * @beacon_int: beacon interval (TODO make interface config) 414 * @flags: configuration flags defined above 415 * @power_level: requested transmit power (in dBm) 416 * @max_antenna_gain: maximum antenna gain (in dBi) 417 * @antenna_sel_tx: transmit antenna selection, 0: default/diversity, 418 * 1/2: antenna 0/1 419 * @antenna_sel_rx: receive antenna selection, like @antenna_sel_tx 420 * @ht_conf: describes current self configuration of 802.11n HT capabilies 421 * @ht_bss_conf: describes current BSS configuration of 802.11n HT parameters 422 * @channel: the channel to tune to 423 */ 424struct ieee80211_conf { 425 int radio_enabled; 426 427 int beacon_int; 428 u32 flags; 429 int power_level; 430 int max_antenna_gain; 431 u8 antenna_sel_tx; 432 u8 antenna_sel_rx; 433 434 struct ieee80211_channel *channel; 435 436 struct ieee80211_ht_info ht_conf; 437 struct ieee80211_ht_bss_info ht_bss_conf; 438}; 439 440/** 441 * enum ieee80211_if_types - types of 802.11 network interfaces 442 * 443 * @IEEE80211_IF_TYPE_INVALID: invalid interface type, not used 444 * by mac80211 itself 445 * @IEEE80211_IF_TYPE_AP: interface in AP mode. 446 * @IEEE80211_IF_TYPE_MGMT: special interface for communication with hostap 447 * daemon. Drivers should never see this type. 448 * @IEEE80211_IF_TYPE_STA: interface in STA (client) mode. 449 * @IEEE80211_IF_TYPE_IBSS: interface in IBSS (ad-hoc) mode. 450 * @IEEE80211_IF_TYPE_MNTR: interface in monitor (rfmon) mode. 451 * @IEEE80211_IF_TYPE_WDS: interface in WDS mode. 452 * @IEEE80211_IF_TYPE_VLAN: VLAN interface bound to an AP, drivers 453 * will never see this type. 454 * @IEEE80211_IF_TYPE_MESH_POINT: 802.11s mesh point 455 */ 456enum ieee80211_if_types { 457 IEEE80211_IF_TYPE_INVALID, 458 IEEE80211_IF_TYPE_AP, 459 IEEE80211_IF_TYPE_STA, 460 IEEE80211_IF_TYPE_IBSS, 461 IEEE80211_IF_TYPE_MESH_POINT, 462 IEEE80211_IF_TYPE_MNTR, 463 IEEE80211_IF_TYPE_WDS, 464 IEEE80211_IF_TYPE_VLAN, 465}; 466 467/** 468 * struct ieee80211_vif - per-interface data 469 * 470 * Data in this structure is continually present for driver 471 * use during the life of a virtual interface. 472 * 473 * @type: type of this virtual interface 474 * @drv_priv: data area for driver use, will always be aligned to 475 * sizeof(void *). 476 */ 477struct ieee80211_vif { 478 enum ieee80211_if_types type; 479 /* must be last */ 480 u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *)))); 481}; 482 483static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif) 484{ 485#ifdef CONFIG_MAC80211_MESH 486 return vif->type == IEEE80211_IF_TYPE_MESH_POINT; 487#endif 488 return false; 489} 490 491/** 492 * struct ieee80211_if_init_conf - initial configuration of an interface 493 * 494 * @vif: pointer to a driver-use per-interface structure. The pointer 495 * itself is also used for various functions including 496 * ieee80211_beacon_get() and ieee80211_get_buffered_bc(). 497 * @type: one of &enum ieee80211_if_types constants. Determines the type of 498 * added/removed interface. 499 * @mac_addr: pointer to MAC address of the interface. This pointer is valid 500 * until the interface is removed (i.e. it cannot be used after 501 * remove_interface() callback was called for this interface). 502 * 503 * This structure is used in add_interface() and remove_interface() 504 * callbacks of &struct ieee80211_hw. 505 * 506 * When you allow multiple interfaces to be added to your PHY, take care 507 * that the hardware can actually handle multiple MAC addresses. However, 508 * also take care that when there's no interface left with mac_addr != %NULL 509 * you remove the MAC address from the device to avoid acknowledging packets 510 * in pure monitor mode. 511 */ 512struct ieee80211_if_init_conf { 513 enum ieee80211_if_types type; 514 struct ieee80211_vif *vif; 515 void *mac_addr; 516}; 517 518/** 519 * struct ieee80211_if_conf - configuration of an interface 520 * 521 * @type: type of the interface. This is always the same as was specified in 522 * &struct ieee80211_if_init_conf. The type of an interface never changes 523 * during the life of the interface; this field is present only for 524 * convenience. 525 * @bssid: BSSID of the network we are associated to/creating. 526 * @ssid: used (together with @ssid_len) by drivers for hardware that 527 * generate beacons independently. The pointer is valid only during the 528 * config_interface() call, so copy the value somewhere if you need 529 * it. 530 * @ssid_len: length of the @ssid field. 531 * @beacon: beacon template. Valid only if @host_gen_beacon_template in 532 * &struct ieee80211_hw is set. The driver is responsible of freeing 533 * the sk_buff. 534 * @beacon_control: tx_control for the beacon template, this field is only 535 * valid when the @beacon field was set. 536 * 537 * This structure is passed to the config_interface() callback of 538 * &struct ieee80211_hw. 539 */ 540struct ieee80211_if_conf { 541 int type; 542 u8 *bssid; 543 u8 *ssid; 544 size_t ssid_len; 545 struct sk_buff *beacon; 546}; 547 548/** 549 * enum ieee80211_key_alg - key algorithm 550 * @ALG_WEP: WEP40 or WEP104 551 * @ALG_TKIP: TKIP 552 * @ALG_CCMP: CCMP (AES) 553 */ 554enum ieee80211_key_alg { 555 ALG_WEP, 556 ALG_TKIP, 557 ALG_CCMP, 558}; 559 560 561/** 562 * enum ieee80211_key_flags - key flags 563 * 564 * These flags are used for communication about keys between the driver 565 * and mac80211, with the @flags parameter of &struct ieee80211_key_conf. 566 * 567 * @IEEE80211_KEY_FLAG_WMM_STA: Set by mac80211, this flag indicates 568 * that the STA this key will be used with could be using QoS. 569 * @IEEE80211_KEY_FLAG_GENERATE_IV: This flag should be set by the 570 * driver to indicate that it requires IV generation for this 571 * particular key. 572 * @IEEE80211_KEY_FLAG_GENERATE_MMIC: This flag should be set by 573 * the driver for a TKIP key if it requires Michael MIC 574 * generation in software. 575 * @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates 576 * that the key is pairwise rather then a shared key. 577 */ 578enum ieee80211_key_flags { 579 IEEE80211_KEY_FLAG_WMM_STA = 1<<0, 580 IEEE80211_KEY_FLAG_GENERATE_IV = 1<<1, 581 IEEE80211_KEY_FLAG_GENERATE_MMIC= 1<<2, 582 IEEE80211_KEY_FLAG_PAIRWISE = 1<<3, 583}; 584 585/** 586 * struct ieee80211_key_conf - key information 587 * 588 * This key information is given by mac80211 to the driver by 589 * the set_key() callback in &struct ieee80211_ops. 590 * 591 * @hw_key_idx: To be set by the driver, this is the key index the driver 592 * wants to be given when a frame is transmitted and needs to be 593 * encrypted in hardware. 594 * @alg: The key algorithm. 595 * @flags: key flags, see &enum ieee80211_key_flags. 596 * @keyidx: the key index (0-3) 597 * @keylen: key material length 598 * @key: key material 599 */ 600struct ieee80211_key_conf { 601 enum ieee80211_key_alg alg; 602 u8 hw_key_idx; 603 u8 flags; 604 s8 keyidx; 605 u8 keylen; 606 u8 key[0]; 607}; 608 609/** 610 * enum set_key_cmd - key command 611 * 612 * Used with the set_key() callback in &struct ieee80211_ops, this 613 * indicates whether a key is being removed or added. 614 * 615 * @SET_KEY: a key is set 616 * @DISABLE_KEY: a key must be disabled 617 */ 618enum set_key_cmd { 619 SET_KEY, DISABLE_KEY, 620}; 621 622/** 623 * enum sta_notify_cmd - sta notify command 624 * 625 * Used with the sta_notify() callback in &struct ieee80211_ops, this 626 * indicates addition and removal of a station to station table 627 * 628 * @STA_NOTIFY_ADD: a station was added to the station table 629 * @STA_NOTIFY_REMOVE: a station being removed from the station table 630 */ 631enum sta_notify_cmd { 632 STA_NOTIFY_ADD, STA_NOTIFY_REMOVE 633}; 634 635/** 636 * enum ieee80211_tkip_key_type - get tkip key 637 * 638 * Used by drivers which need to get a tkip key for skb. Some drivers need a 639 * phase 1 key, others need a phase 2 key. A single function allows the driver 640 * to get the key, this enum indicates what type of key is required. 641 * 642 * @IEEE80211_TKIP_P1_KEY: the driver needs a phase 1 key 643 * @IEEE80211_TKIP_P2_KEY: the driver needs a phase 2 key 644 */ 645enum ieee80211_tkip_key_type { 646 IEEE80211_TKIP_P1_KEY, 647 IEEE80211_TKIP_P2_KEY, 648}; 649 650/** 651 * enum ieee80211_hw_flags - hardware flags 652 * 653 * These flags are used to indicate hardware capabilities to 654 * the stack. Generally, flags here should have their meaning 655 * done in a way that the simplest hardware doesn't need setting 656 * any particular flags. There are some exceptions to this rule, 657 * however, so you are advised to review these flags carefully. 658 * 659 * @IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE: 660 * The device only needs to be supplied with a beacon template. 661 * If you need the host to generate each beacon then don't use 662 * this flag and call ieee80211_beacon_get() when you need the 663 * next beacon frame. Note that if you set this flag, you must 664 * implement the set_tim() callback for powersave mode to work 665 * properly. 666 * This flag is only relevant for access-point mode. 667 * 668 * @IEEE80211_HW_RX_INCLUDES_FCS: 669 * Indicates that received frames passed to the stack include 670 * the FCS at the end. 671 * 672 * @IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING: 673 * Some wireless LAN chipsets buffer broadcast/multicast frames 674 * for power saving stations in the hardware/firmware and others 675 * rely on the host system for such buffering. This option is used 676 * to configure the IEEE 802.11 upper layer to buffer broadcast and 677 * multicast frames when there are power saving stations so that 678 * the driver can fetch them with ieee80211_get_buffered_bc(). Note 679 * that not setting this flag works properly only when the 680 * %IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE is also not set because 681 * otherwise the stack will not know when the DTIM beacon was sent. 682 * 683 * @IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE: 684 * Hardware is not capable of short slot operation on the 2.4 GHz band. 685 * 686 * @IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE: 687 * Hardware is not capable of receiving frames with short preamble on 688 * the 2.4 GHz band. 689 * 690 * @IEEE80211_HW_SIGNAL_UNSPEC: 691 * Hardware can provide signal values but we don't know its units. We 692 * expect values between 0 and @max_signal. 693 * If possible please provide dB or dBm instead. 694 * 695 * @IEEE80211_HW_SIGNAL_DB: 696 * Hardware gives signal values in dB, decibel difference from an 697 * arbitrary, fixed reference. We expect values between 0 and @max_signal. 698 * If possible please provide dBm instead. 699 * 700 * @IEEE80211_HW_SIGNAL_DBM: 701 * Hardware gives signal values in dBm, decibel difference from 702 * one milliwatt. This is the preferred method since it is standardized 703 * between different devices. @max_signal does not need to be set. 704 * 705 * @IEEE80211_HW_NOISE_DBM: 706 * Hardware can provide noise (radio interference) values in units dBm, 707 * decibel difference from one milliwatt. 708 */ 709enum ieee80211_hw_flags { 710 IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE = 1<<0, 711 IEEE80211_HW_RX_INCLUDES_FCS = 1<<1, 712 IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING = 1<<2, 713 IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE = 1<<3, 714 IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE = 1<<4, 715 IEEE80211_HW_SIGNAL_UNSPEC = 1<<5, 716 IEEE80211_HW_SIGNAL_DB = 1<<6, 717 IEEE80211_HW_SIGNAL_DBM = 1<<7, 718 IEEE80211_HW_NOISE_DBM = 1<<8, 719}; 720 721/** 722 * struct ieee80211_hw - hardware information and state 723 * 724 * This structure contains the configuration and hardware 725 * information for an 802.11 PHY. 726 * 727 * @wiphy: This points to the &struct wiphy allocated for this 728 * 802.11 PHY. You must fill in the @perm_addr and @dev 729 * members of this structure using SET_IEEE80211_DEV() 730 * and SET_IEEE80211_PERM_ADDR(). Additionally, all supported 731 * bands (with channels, bitrates) are registered here. 732 * 733 * @conf: &struct ieee80211_conf, device configuration, don't use. 734 * 735 * @workqueue: single threaded workqueue available for driver use, 736 * allocated by mac80211 on registration and flushed on 737 * unregistration. 738 * 739 * @priv: pointer to private area that was allocated for driver use 740 * along with this structure. 741 * 742 * @flags: hardware flags, see &enum ieee80211_hw_flags. 743 * 744 * @extra_tx_headroom: headroom to reserve in each transmit skb 745 * for use by the driver (e.g. for transmit headers.) 746 * 747 * @channel_change_time: time (in microseconds) it takes to change channels. 748 * 749 * @max_signal: Maximum value for signal (rssi) in RX information, used 750 * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB 751 * 752 * @queues: number of available hardware transmit queues for 753 * data packets. WMM/QoS requires at least four, these 754 * queues need to have configurable access parameters. 755 * 756 * @ampdu_queues: number of available hardware transmit queues 757 * for A-MPDU packets, these have no access parameters 758 * because they're used only for A-MPDU frames. Note that 759 * mac80211 will not currently use any of the regular queues 760 * for aggregation. 761 * 762 * @rate_control_algorithm: rate control algorithm for this hardware. 763 * If unset (NULL), the default algorithm will be used. Must be 764 * set before calling ieee80211_register_hw(). 765 * 766 * @vif_data_size: size (in bytes) of the drv_priv data area 767 * within &struct ieee80211_vif. 768 */ 769struct ieee80211_hw { 770 struct ieee80211_conf conf; 771 struct wiphy *wiphy; 772 struct workqueue_struct *workqueue; 773 const char *rate_control_algorithm; 774 void *priv; 775 u32 flags; 776 unsigned int extra_tx_headroom; 777 int channel_change_time; 778 int vif_data_size; 779 u16 queues, ampdu_queues; 780 s8 max_signal; 781}; 782 783/** 784 * SET_IEEE80211_DEV - set device for 802.11 hardware 785 * 786 * @hw: the &struct ieee80211_hw to set the device for 787 * @dev: the &struct device of this 802.11 device 788 */ 789static inline void SET_IEEE80211_DEV(struct ieee80211_hw *hw, struct device *dev) 790{ 791 set_wiphy_dev(hw->wiphy, dev); 792} 793 794/** 795 * SET_IEEE80211_PERM_ADDR - set the permanenet MAC address for 802.11 hardware 796 * 797 * @hw: the &struct ieee80211_hw to set the MAC address for 798 * @addr: the address to set 799 */ 800static inline void SET_IEEE80211_PERM_ADDR(struct ieee80211_hw *hw, u8 *addr) 801{ 802 memcpy(hw->wiphy->perm_addr, addr, ETH_ALEN); 803} 804 805static inline struct ieee80211_rate * 806ieee80211_get_tx_rate(const struct ieee80211_hw *hw, 807 const struct ieee80211_tx_info *c) 808{ 809 if (WARN_ON(c->tx_rate_idx < 0)) 810 return NULL; 811 return &hw->wiphy->bands[c->band]->bitrates[c->tx_rate_idx]; 812} 813 814static inline struct ieee80211_rate * 815ieee80211_get_rts_cts_rate(const struct ieee80211_hw *hw, 816 const struct ieee80211_tx_info *c) 817{ 818 if (c->control.rts_cts_rate_idx < 0) 819 return NULL; 820 return &hw->wiphy->bands[c->band]->bitrates[c->control.rts_cts_rate_idx]; 821} 822 823static inline struct ieee80211_rate * 824ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw, 825 const struct ieee80211_tx_info *c) 826{ 827 if (c->control.alt_retry_rate_idx < 0) 828 return NULL; 829 return &hw->wiphy->bands[c->band]->bitrates[c->control.alt_retry_rate_idx]; 830} 831 832/** 833 * DOC: Hardware crypto acceleration 834 * 835 * mac80211 is capable of taking advantage of many hardware 836 * acceleration designs for encryption and decryption operations. 837 * 838 * The set_key() callback in the &struct ieee80211_ops for a given 839 * device is called to enable hardware acceleration of encryption and 840 * decryption. The callback takes an @address parameter that will be 841 * the broadcast address for default keys, the other station's hardware 842 * address for individual keys or the zero address for keys that will 843 * be used only for transmission. 844 * Multiple transmission keys with the same key index may be used when 845 * VLANs are configured for an access point. 846 * 847 * The @local_address parameter will always be set to our own address, 848 * this is only relevant if you support multiple local addresses. 849 * 850 * When transmitting, the TX control data will use the @hw_key_idx 851 * selected by the driver by modifying the &struct ieee80211_key_conf 852 * pointed to by the @key parameter to the set_key() function. 853 * 854 * The set_key() call for the %SET_KEY command should return 0 if 855 * the key is now in use, -%EOPNOTSUPP or -%ENOSPC if it couldn't be 856 * added; if you return 0 then hw_key_idx must be assigned to the 857 * hardware key index, you are free to use the full u8 range. 858 * 859 * When the cmd is %DISABLE_KEY then it must succeed. 860 * 861 * Note that it is permissible to not decrypt a frame even if a key 862 * for it has been uploaded to hardware, the stack will not make any 863 * decision based on whether a key has been uploaded or not but rather 864 * based on the receive flags. 865 * 866 * The &struct ieee80211_key_conf structure pointed to by the @key 867 * parameter is guaranteed to be valid until another call to set_key() 868 * removes it, but it can only be used as a cookie to differentiate 869 * keys. 870 * 871 * In TKIP some HW need to be provided a phase 1 key, for RX decryption 872 * acceleration (i.e. iwlwifi). Those drivers should provide update_tkip_key 873 * handler. 874 * The update_tkip_key() call updates the driver with the new phase 1 key. 875 * This happens everytime the iv16 wraps around (every 65536 packets). The 876 * set_key() call will happen only once for each key (unless the AP did 877 * rekeying), it will not include a valid phase 1 key. The valid phase 1 key is 878 * provided by udpate_tkip_key only. The trigger that makes mac80211 call this 879 * handler is software decryption with wrap around of iv16. 880 */ 881 882/** 883 * DOC: Frame filtering 884 * 885 * mac80211 requires to see many management frames for proper 886 * operation, and users may want to see many more frames when 887 * in monitor mode. However, for best CPU usage and power consumption, 888 * having as few frames as possible percolate through the stack is 889 * desirable. Hence, the hardware should filter as much as possible. 890 * 891 * To achieve this, mac80211 uses filter flags (see below) to tell 892 * the driver's configure_filter() function which frames should be 893 * passed to mac80211 and which should be filtered out. 894 * 895 * The configure_filter() callback is invoked with the parameters 896 * @mc_count and @mc_list for the combined multicast address list 897 * of all virtual interfaces, @changed_flags telling which flags 898 * were changed and @total_flags with the new flag states. 899 * 900 * If your device has no multicast address filters your driver will 901 * need to check both the %FIF_ALLMULTI flag and the @mc_count 902 * parameter to see whether multicast frames should be accepted 903 * or dropped. 904 * 905 * All unsupported flags in @total_flags must be cleared. 906 * Hardware does not support a flag if it is incapable of _passing_ 907 * the frame to the stack. Otherwise the driver must ignore 908 * the flag, but not clear it. 909 * You must _only_ clear the flag (announce no support for the 910 * flag to mac80211) if you are not able to pass the packet type 911 * to the stack (so the hardware always filters it). 912 * So for example, you should clear @FIF_CONTROL, if your hardware 913 * always filters control frames. If your hardware always passes 914 * control frames to the kernel and is incapable of filtering them, 915 * you do _not_ clear the @FIF_CONTROL flag. 916 * This rule applies to all other FIF flags as well. 917 */ 918 919/** 920 * enum ieee80211_filter_flags - hardware filter flags 921 * 922 * These flags determine what the filter in hardware should be 923 * programmed to let through and what should not be passed to the 924 * stack. It is always safe to pass more frames than requested, 925 * but this has negative impact on power consumption. 926 * 927 * @FIF_PROMISC_IN_BSS: promiscuous mode within your BSS, 928 * think of the BSS as your network segment and then this corresponds 929 * to the regular ethernet device promiscuous mode. 930 * 931 * @FIF_ALLMULTI: pass all multicast frames, this is used if requested 932 * by the user or if the hardware is not capable of filtering by 933 * multicast address. 934 * 935 * @FIF_FCSFAIL: pass frames with failed FCS (but you need to set the 936 * %RX_FLAG_FAILED_FCS_CRC for them) 937 * 938 * @FIF_PLCPFAIL: pass frames with failed PLCP CRC (but you need to set 939 * the %RX_FLAG_FAILED_PLCP_CRC for them 940 * 941 * @FIF_BCN_PRBRESP_PROMISC: This flag is set during scanning to indicate 942 * to the hardware that it should not filter beacons or probe responses 943 * by BSSID. Filtering them can greatly reduce the amount of processing 944 * mac80211 needs to do and the amount of CPU wakeups, so you should 945 * honour this flag if possible. 946 * 947 * @FIF_CONTROL: pass control frames, if PROMISC_IN_BSS is not set then 948 * only those addressed to this station 949 * 950 * @FIF_OTHER_BSS: pass frames destined to other BSSes 951 */ 952enum ieee80211_filter_flags { 953 FIF_PROMISC_IN_BSS = 1<<0, 954 FIF_ALLMULTI = 1<<1, 955 FIF_FCSFAIL = 1<<2, 956 FIF_PLCPFAIL = 1<<3, 957 FIF_BCN_PRBRESP_PROMISC = 1<<4, 958 FIF_CONTROL = 1<<5, 959 FIF_OTHER_BSS = 1<<6, 960}; 961 962/** 963 * enum ieee80211_ampdu_mlme_action - A-MPDU actions 964 * 965 * These flags are used with the ampdu_action() callback in 966 * &struct ieee80211_ops to indicate which action is needed. 967 * @IEEE80211_AMPDU_RX_START: start Rx aggregation 968 * @IEEE80211_AMPDU_RX_STOP: stop Rx aggregation 969 * @IEEE80211_AMPDU_TX_START: start Tx aggregation 970 * @IEEE80211_AMPDU_TX_STOP: stop Tx aggregation 971 */ 972enum ieee80211_ampdu_mlme_action { 973 IEEE80211_AMPDU_RX_START, 974 IEEE80211_AMPDU_RX_STOP, 975 IEEE80211_AMPDU_TX_START, 976 IEEE80211_AMPDU_TX_STOP, 977}; 978 979/** 980 * struct ieee80211_ops - callbacks from mac80211 to the driver 981 * 982 * This structure contains various callbacks that the driver may 983 * handle or, in some cases, must handle, for example to configure 984 * the hardware to a new channel or to transmit a frame. 985 * 986 * @tx: Handler that 802.11 module calls for each transmitted frame. 987 * skb contains the buffer starting from the IEEE 802.11 header. 988 * The low-level driver should send the frame out based on 989 * configuration in the TX control data. Must be implemented and 990 * atomic. 991 * 992 * @start: Called before the first netdevice attached to the hardware 993 * is enabled. This should turn on the hardware and must turn on 994 * frame reception (for possibly enabled monitor interfaces.) 995 * Returns negative error codes, these may be seen in userspace, 996 * or zero. 997 * When the device is started it should not have a MAC address 998 * to avoid acknowledging frames before a non-monitor device 999 * is added. 1000 * Must be implemented. 1001 * 1002 * @stop: Called after last netdevice attached to the hardware 1003 * is disabled. This should turn off the hardware (at least 1004 * it must turn off frame reception.) 1005 * May be called right after add_interface if that rejects 1006 * an interface. 1007 * Must be implemented. 1008 * 1009 * @add_interface: Called when a netdevice attached to the hardware is 1010 * enabled. Because it is not called for monitor mode devices, @open 1011 * and @stop must be implemented. 1012 * The driver should perform any initialization it needs before 1013 * the device can be enabled. The initial configuration for the 1014 * interface is given in the conf parameter. 1015 * The callback may refuse to add an interface by returning a 1016 * negative error code (which will be seen in userspace.) 1017 * Must be implemented. 1018 * 1019 * @remove_interface: Notifies a driver that an interface is going down. 1020 * The @stop callback is called after this if it is the last interface 1021 * and no monitor interfaces are present. 1022 * When all interfaces are removed, the MAC address in the hardware 1023 * must be cleared so the device no longer acknowledges packets, 1024 * the mac_addr member of the conf structure is, however, set to the 1025 * MAC address of the device going away. 1026 * Hence, this callback must be implemented. 1027 * 1028 * @config: Handler for configuration requests. IEEE 802.11 code calls this 1029 * function to change hardware configuration, e.g., channel. 1030 * 1031 * @config_interface: Handler for configuration requests related to interfaces 1032 * (e.g. BSSID changes.) 1033 * 1034 * @bss_info_changed: Handler for configuration requests related to BSS 1035 * parameters that may vary during BSS's lifespan, and may affect low 1036 * level driver (e.g. assoc/disassoc status, erp parameters). 1037 * This function should not be used if no BSS has been set, unless 1038 * for association indication. The @changed parameter indicates which 1039 * of the bss parameters has changed when a call is made. 1040 * 1041 * @configure_filter: Configure the device's RX filter. 1042 * See the section "Frame filtering" for more information. 1043 * This callback must be implemented and atomic. 1044 * 1045 * @set_tim: Set TIM bit. If the hardware/firmware takes care of beacon 1046 * generation (that is, %IEEE80211_HW_HOST_GEN_BEACON_TEMPLATE is set) 1047 * mac80211 calls this function when a TIM bit must be set or cleared 1048 * for a given AID. Must be atomic. 1049 * 1050 * @set_key: See the section "Hardware crypto acceleration" 1051 * This callback can sleep, and is only called between add_interface 1052 * and remove_interface calls, i.e. while the interface with the 1053 * given local_address is enabled. 1054 * 1055 * @update_tkip_key: See the section "Hardware crypto acceleration" 1056 * This callback will be called in the context of Rx. Called for drivers 1057 * which set IEEE80211_KEY_FLAG_TKIP_REQ_RX_P1_KEY. 1058 * 1059 * @hw_scan: Ask the hardware to service the scan request, no need to start 1060 * the scan state machine in stack. The scan must honour the channel 1061 * configuration done by the regulatory agent in the wiphy's registered 1062 * bands. 1063 * 1064 * @get_stats: return low-level statistics 1065 * 1066 * @get_tkip_seq: If your device implements TKIP encryption in hardware this 1067 * callback should be provided to read the TKIP transmit IVs (both IV32 1068 * and IV16) for the given key from hardware. 1069 * 1070 * @set_rts_threshold: Configuration of RTS threshold (if device needs it) 1071 * 1072 * @set_frag_threshold: Configuration of fragmentation threshold. Assign this if 1073 * the device does fragmentation by itself; if this method is assigned then 1074 * the stack will not do fragmentation. 1075 * 1076 * @set_retry_limit: Configuration of retry limits (if device needs it) 1077 * 1078 * @sta_notify: Notifies low level driver about addition or removal 1079 * of assocaited station or AP. 1080 * 1081 * @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max), 1082 * bursting) for a hardware TX queue. Must be atomic. 1083 * 1084 * @get_tx_stats: Get statistics of the current TX queue status. This is used 1085 * to get number of currently queued packets (queue length), maximum queue 1086 * size (limit), and total number of packets sent using each TX queue 1087 * (count). The 'stats' pointer points to an array that has hw->queues + 1088 * hw->ampdu_queues items. 1089 * 1090 * @get_tsf: Get the current TSF timer value from firmware/hardware. Currently, 1091 * this is only used for IBSS mode debugging and, as such, is not a 1092 * required function. Must be atomic. 1093 * 1094 * @reset_tsf: Reset the TSF timer and allow firmware/hardware to synchronize 1095 * with other STAs in the IBSS. This is only used in IBSS mode. This 1096 * function is optional if the firmware/hardware takes full care of 1097 * TSF synchronization. 1098 * 1099 * @beacon_update: Setup beacon data for IBSS beacons. Unlike access point, 1100 * IBSS uses a fixed beacon frame which is configured using this 1101 * function. 1102 * If the driver returns success (0) from this callback, it owns 1103 * the skb. That means the driver is responsible to kfree_skb() it. 1104 * The control structure is not dynamically allocated. That means the 1105 * driver does not own the pointer and if it needs it somewhere 1106 * outside of the context of this function, it must copy it 1107 * somewhere else. 1108 * This handler is required only for IBSS mode. 1109 * 1110 * @tx_last_beacon: Determine whether the last IBSS beacon was sent by us. 1111 * This is needed only for IBSS mode and the result of this function is 1112 * used to determine whether to reply to Probe Requests. 1113 * 1114 * @conf_ht: Configures low level driver with 802.11n HT data. Must be atomic. 1115 * 1116 * @ampdu_action: Perform a certain A-MPDU action 1117 * The RA/TID combination determines the destination and TID we want 1118 * the ampdu action to be performed for. The action is defined through 1119 * ieee80211_ampdu_mlme_action. Starting sequence number (@ssn) 1120 * is the first frame we expect to perform the action on. notice 1121 * that TX/RX_STOP can pass NULL for this parameter. 1122 */ 1123struct ieee80211_ops { 1124 int (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb); 1125 int (*start)(struct ieee80211_hw *hw); 1126 void (*stop)(struct ieee80211_hw *hw); 1127 int (*add_interface)(struct ieee80211_hw *hw, 1128 struct ieee80211_if_init_conf *conf); 1129 void (*remove_interface)(struct ieee80211_hw *hw, 1130 struct ieee80211_if_init_conf *conf); 1131 int (*config)(struct ieee80211_hw *hw, struct ieee80211_conf *conf); 1132 int (*config_interface)(struct ieee80211_hw *hw, 1133 struct ieee80211_vif *vif, 1134 struct ieee80211_if_conf *conf); 1135 void (*bss_info_changed)(struct ieee80211_hw *hw, 1136 struct ieee80211_vif *vif, 1137 struct ieee80211_bss_conf *info, 1138 u32 changed); 1139 void (*configure_filter)(struct ieee80211_hw *hw, 1140 unsigned int changed_flags, 1141 unsigned int *total_flags, 1142 int mc_count, struct dev_addr_list *mc_list); 1143 int (*set_tim)(struct ieee80211_hw *hw, int aid, int set); 1144 int (*set_key)(struct ieee80211_hw *hw, enum set_key_cmd cmd, 1145 const u8 *local_address, const u8 *address, 1146 struct ieee80211_key_conf *key); 1147 void (*update_tkip_key)(struct ieee80211_hw *hw, 1148 struct ieee80211_key_conf *conf, const u8 *address, 1149 u32 iv32, u16 *phase1key); 1150 int (*hw_scan)(struct ieee80211_hw *hw, u8 *ssid, size_t len); 1151 int (*get_stats)(struct ieee80211_hw *hw, 1152 struct ieee80211_low_level_stats *stats); 1153 void (*get_tkip_seq)(struct ieee80211_hw *hw, u8 hw_key_idx, 1154 u32 *iv32, u16 *iv16); 1155 int (*set_rts_threshold)(struct ieee80211_hw *hw, u32 value); 1156 int (*set_frag_threshold)(struct ieee80211_hw *hw, u32 value); 1157 int (*set_retry_limit)(struct ieee80211_hw *hw, 1158 u32 short_retry, u32 long_retr); 1159 void (*sta_notify)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 1160 enum sta_notify_cmd, const u8 *addr); 1161 int (*conf_tx)(struct ieee80211_hw *hw, u16 queue, 1162 const struct ieee80211_tx_queue_params *params); 1163 int (*get_tx_stats)(struct ieee80211_hw *hw, 1164 struct ieee80211_tx_queue_stats *stats); 1165 u64 (*get_tsf)(struct ieee80211_hw *hw); 1166 void (*reset_tsf)(struct ieee80211_hw *hw); 1167 int (*beacon_update)(struct ieee80211_hw *hw, 1168 struct sk_buff *skb); 1169 int (*tx_last_beacon)(struct ieee80211_hw *hw); 1170 int (*ampdu_action)(struct ieee80211_hw *hw, 1171 enum ieee80211_ampdu_mlme_action action, 1172 const u8 *addr, u16 tid, u16 *ssn); 1173}; 1174 1175/** 1176 * ieee80211_alloc_hw - Allocate a new hardware device 1177 * 1178 * This must be called once for each hardware device. The returned pointer 1179 * must be used to refer to this device when calling other functions. 1180 * mac80211 allocates a private data area for the driver pointed to by 1181 * @priv in &struct ieee80211_hw, the size of this area is given as 1182 * @priv_data_len. 1183 * 1184 * @priv_data_len: length of private data 1185 * @ops: callbacks for this device 1186 */ 1187struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len, 1188 const struct ieee80211_ops *ops); 1189 1190/** 1191 * ieee80211_register_hw - Register hardware device 1192 * 1193 * You must call this function before any other functions in 1194 * mac80211. Note that before a hardware can be registered, you 1195 * need to fill the contained wiphy's information. 1196 * 1197 * @hw: the device to register as returned by ieee80211_alloc_hw() 1198 */ 1199int ieee80211_register_hw(struct ieee80211_hw *hw); 1200 1201#ifdef CONFIG_MAC80211_LEDS 1202extern char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw); 1203extern char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw); 1204extern char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw); 1205extern char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw); 1206#endif 1207/** 1208 * ieee80211_get_tx_led_name - get name of TX LED 1209 * 1210 * mac80211 creates a transmit LED trigger for each wireless hardware 1211 * that can be used to drive LEDs if your driver registers a LED device. 1212 * This function returns the name (or %NULL if not configured for LEDs) 1213 * of the trigger so you can automatically link the LED device. 1214 * 1215 * @hw: the hardware to get the LED trigger name for 1216 */ 1217static inline char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw) 1218{ 1219#ifdef CONFIG_MAC80211_LEDS 1220 return __ieee80211_get_tx_led_name(hw); 1221#else 1222 return NULL; 1223#endif 1224} 1225 1226/** 1227 * ieee80211_get_rx_led_name - get name of RX LED 1228 * 1229 * mac80211 creates a receive LED trigger for each wireless hardware 1230 * that can be used to drive LEDs if your driver registers a LED device. 1231 * This function returns the name (or %NULL if not configured for LEDs) 1232 * of the trigger so you can automatically link the LED device. 1233 * 1234 * @hw: the hardware to get the LED trigger name for 1235 */ 1236static inline char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw) 1237{ 1238#ifdef CONFIG_MAC80211_LEDS 1239 return __ieee80211_get_rx_led_name(hw); 1240#else 1241 return NULL; 1242#endif 1243} 1244 1245/** 1246 * ieee80211_get_assoc_led_name - get name of association LED 1247 * 1248 * mac80211 creates a association LED trigger for each wireless hardware 1249 * that can be used to drive LEDs if your driver registers a LED device. 1250 * This function returns the name (or %NULL if not configured for LEDs) 1251 * of the trigger so you can automatically link the LED device. 1252 * 1253 * @hw: the hardware to get the LED trigger name for 1254 */ 1255static inline char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw) 1256{ 1257#ifdef CONFIG_MAC80211_LEDS 1258 return __ieee80211_get_assoc_led_name(hw); 1259#else 1260 return NULL; 1261#endif 1262} 1263 1264/** 1265 * ieee80211_get_radio_led_name - get name of radio LED 1266 * 1267 * mac80211 creates a radio change LED trigger for each wireless hardware 1268 * that can be used to drive LEDs if your driver registers a LED device. 1269 * This function returns the name (or %NULL if not configured for LEDs) 1270 * of the trigger so you can automatically link the LED device. 1271 * 1272 * @hw: the hardware to get the LED trigger name for 1273 */ 1274static inline char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw) 1275{ 1276#ifdef CONFIG_MAC80211_LEDS 1277 return __ieee80211_get_radio_led_name(hw); 1278#else 1279 return NULL; 1280#endif 1281} 1282 1283/** 1284 * ieee80211_unregister_hw - Unregister a hardware device 1285 * 1286 * This function instructs mac80211 to free allocated resources 1287 * and unregister netdevices from the networking subsystem. 1288 * 1289 * @hw: the hardware to unregister 1290 */ 1291void ieee80211_unregister_hw(struct ieee80211_hw *hw); 1292 1293/** 1294 * ieee80211_free_hw - free hardware descriptor 1295 * 1296 * This function frees everything that was allocated, including the 1297 * private data for the driver. You must call ieee80211_unregister_hw() 1298 * before calling this function 1299 * 1300 * @hw: the hardware to free 1301 */ 1302void ieee80211_free_hw(struct ieee80211_hw *hw); 1303 1304/* trick to avoid symbol clashes with the ieee80211 subsystem */ 1305void __ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb, 1306 struct ieee80211_rx_status *status); 1307 1308/** 1309 * ieee80211_rx - receive frame 1310 * 1311 * Use this function to hand received frames to mac80211. The receive 1312 * buffer in @skb must start with an IEEE 802.11 header or a radiotap 1313 * header if %RX_FLAG_RADIOTAP is set in the @status flags. 1314 * 1315 * This function may not be called in IRQ context. Calls to this function 1316 * for a single hardware must be synchronized against each other. Calls 1317 * to this function and ieee80211_rx_irqsafe() may not be mixed for a 1318 * single hardware. 1319 * 1320 * @hw: the hardware this frame came in on 1321 * @skb: the buffer to receive, owned by mac80211 after this call 1322 * @status: status of this frame; the status pointer need not be valid 1323 * after this function returns 1324 */ 1325static inline void ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb, 1326 struct ieee80211_rx_status *status) 1327{ 1328 __ieee80211_rx(hw, skb, status); 1329} 1330 1331/** 1332 * ieee80211_rx_irqsafe - receive frame 1333 * 1334 * Like ieee80211_rx() but can be called in IRQ context 1335 * (internally defers to a tasklet.) 1336 * 1337 * Calls to this function and ieee80211_rx() may not be mixed for a 1338 * single hardware. 1339 * 1340 * @hw: the hardware this frame came in on 1341 * @skb: the buffer to receive, owned by mac80211 after this call 1342 * @status: status of this frame; the status pointer need not be valid 1343 * after this function returns and is not freed by mac80211, 1344 * it is recommended that it points to a stack area 1345 */ 1346void ieee80211_rx_irqsafe(struct ieee80211_hw *hw, 1347 struct sk_buff *skb, 1348 struct ieee80211_rx_status *status); 1349 1350/** 1351 * ieee80211_tx_status - transmit status callback 1352 * 1353 * Call this function for all transmitted frames after they have been 1354 * transmitted. It is permissible to not call this function for 1355 * multicast frames but this can affect statistics. 1356 * 1357 * This function may not be called in IRQ context. Calls to this function 1358 * for a single hardware must be synchronized against each other. Calls 1359 * to this function and ieee80211_tx_status_irqsafe() may not be mixed 1360 * for a single hardware. 1361 * 1362 * @hw: the hardware the frame was transmitted by 1363 * @skb: the frame that was transmitted, owned by mac80211 after this call 1364 */ 1365void ieee80211_tx_status(struct ieee80211_hw *hw, 1366 struct sk_buff *skb); 1367 1368/** 1369 * ieee80211_tx_status_irqsafe - irq-safe transmit status callback 1370 * 1371 * Like ieee80211_tx_status() but can be called in IRQ context 1372 * (internally defers to a tasklet.) 1373 * 1374 * Calls to this function and ieee80211_tx_status() may not be mixed for a 1375 * single hardware. 1376 * 1377 * @hw: the hardware the frame was transmitted by 1378 * @skb: the frame that was transmitted, owned by mac80211 after this call 1379 */ 1380void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw, 1381 struct sk_buff *skb); 1382 1383/** 1384 * ieee80211_beacon_get - beacon generation function 1385 * @hw: pointer obtained from ieee80211_alloc_hw(). 1386 * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf. 1387 * @control: will be filled with information needed to send this beacon. 1388 * 1389 * If the beacon frames are generated by the host system (i.e., not in 1390 * hardware/firmware), the low-level driver uses this function to receive 1391 * the next beacon frame from the 802.11 code. The low-level is responsible 1392 * for calling this function before beacon data is needed (e.g., based on 1393 * hardware interrupt). Returned skb is used only once and low-level driver 1394 * is responsible of freeing it. 1395 */ 1396struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw, 1397 struct ieee80211_vif *vif); 1398 1399/** 1400 * ieee80211_rts_get - RTS frame generation function 1401 * @hw: pointer obtained from ieee80211_alloc_hw(). 1402 * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf. 1403 * @frame: pointer to the frame that is going to be protected by the RTS. 1404 * @frame_len: the frame length (in octets). 1405 * @frame_txctl: &struct ieee80211_tx_info of the frame. 1406 * @rts: The buffer where to store the RTS frame. 1407 * 1408 * If the RTS frames are generated by the host system (i.e., not in 1409 * hardware/firmware), the low-level driver uses this function to receive 1410 * the next RTS frame from the 802.11 code. The low-level is responsible 1411 * for calling this function before and RTS frame is needed. 1412 */ 1413void ieee80211_rts_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 1414 const void *frame, size_t frame_len, 1415 const struct ieee80211_tx_info *frame_txctl, 1416 struct ieee80211_rts *rts); 1417 1418/** 1419 * ieee80211_rts_duration - Get the duration field for an RTS frame 1420 * @hw: pointer obtained from ieee80211_alloc_hw(). 1421 * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf. 1422 * @frame_len: the length of the frame that is going to be protected by the RTS. 1423 * @frame_txctl: &struct ieee80211_tx_info of the frame. 1424 * 1425 * If the RTS is generated in firmware, but the host system must provide 1426 * the duration field, the low-level driver uses this function to receive 1427 * the duration field value in little-endian byteorder. 1428 */ 1429__le16 ieee80211_rts_duration(struct ieee80211_hw *hw, 1430 struct ieee80211_vif *vif, size_t frame_len, 1431 const struct ieee80211_tx_info *frame_txctl); 1432 1433/** 1434 * ieee80211_ctstoself_get - CTS-to-self frame generation function 1435 * @hw: pointer obtained from ieee80211_alloc_hw(). 1436 * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf. 1437 * @frame: pointer to the frame that is going to be protected by the CTS-to-self. 1438 * @frame_len: the frame length (in octets). 1439 * @frame_txctl: &struct ieee80211_tx_info of the frame. 1440 * @cts: The buffer where to store the CTS-to-self frame. 1441 * 1442 * If the CTS-to-self frames are generated by the host system (i.e., not in 1443 * hardware/firmware), the low-level driver uses this function to receive 1444 * the next CTS-to-self frame from the 802.11 code. The low-level is responsible 1445 * for calling this function before and CTS-to-self frame is needed. 1446 */ 1447void ieee80211_ctstoself_get(struct ieee80211_hw *hw, 1448 struct ieee80211_vif *vif, 1449 const void *frame, size_t frame_len, 1450 const struct ieee80211_tx_info *frame_txctl, 1451 struct ieee80211_cts *cts); 1452 1453/** 1454 * ieee80211_ctstoself_duration - Get the duration field for a CTS-to-self frame 1455 * @hw: pointer obtained from ieee80211_alloc_hw(). 1456 * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf. 1457 * @frame_len: the length of the frame that is going to be protected by the CTS-to-self. 1458 * @frame_txctl: &struct ieee80211_tx_info of the frame. 1459 * 1460 * If the CTS-to-self is generated in firmware, but the host system must provide 1461 * the duration field, the low-level driver uses this function to receive 1462 * the duration field value in little-endian byteorder. 1463 */ 1464__le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw, 1465 struct ieee80211_vif *vif, 1466 size_t frame_len, 1467 const struct ieee80211_tx_info *frame_txctl); 1468 1469/** 1470 * ieee80211_generic_frame_duration - Calculate the duration field for a frame 1471 * @hw: pointer obtained from ieee80211_alloc_hw(). 1472 * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf. 1473 * @frame_len: the length of the frame. 1474 * @rate: the rate at which the frame is going to be transmitted. 1475 * 1476 * Calculate the duration field of some generic frame, given its 1477 * length and transmission rate (in 100kbps). 1478 */ 1479__le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw, 1480 struct ieee80211_vif *vif, 1481 size_t frame_len, 1482 struct ieee80211_rate *rate); 1483 1484/** 1485 * ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames 1486 * @hw: pointer as obtained from ieee80211_alloc_hw(). 1487 * @vif: &struct ieee80211_vif pointer from &struct ieee80211_if_init_conf. 1488 * @control: will be filled with information needed to send returned frame. 1489 * 1490 * Function for accessing buffered broadcast and multicast frames. If 1491 * hardware/firmware does not implement buffering of broadcast/multicast 1492 * frames when power saving is used, 802.11 code buffers them in the host 1493 * memory. The low-level driver uses this function to fetch next buffered 1494 * frame. In most cases, this is used when generating beacon frame. This 1495 * function returns a pointer to the next buffered skb or NULL if no more 1496 * buffered frames are available. 1497 * 1498 * Note: buffered frames are returned only after DTIM beacon frame was 1499 * generated with ieee80211_beacon_get() and the low-level driver must thus 1500 * call ieee80211_beacon_get() first. ieee80211_get_buffered_bc() returns 1501 * NULL if the previous generated beacon was not DTIM, so the low-level driver 1502 * does not need to check for DTIM beacons separately and should be able to 1503 * use common code for all beacons. 1504 */ 1505struct sk_buff * 1506ieee80211_get_buffered_bc(struct ieee80211_hw *hw, struct ieee80211_vif *vif); 1507 1508/** 1509 * ieee80211_get_hdrlen_from_skb - get header length from data 1510 * 1511 * Given an skb with a raw 802.11 header at the data pointer this function 1512 * returns the 802.11 header length in bytes (not including encryption 1513 * headers). If the data in the sk_buff is too short to contain a valid 802.11 1514 * header the function returns 0. 1515 * 1516 * @skb: the frame 1517 */ 1518int ieee80211_get_hdrlen_from_skb(const struct sk_buff *skb); 1519 1520/** 1521 * ieee80211_get_hdrlen - get header length from frame control 1522 * 1523 * This function returns the 802.11 header length in bytes (not including 1524 * encryption headers.) 1525 * 1526 * @fc: the frame control field (in CPU endianness) 1527 */ 1528int ieee80211_get_hdrlen(u16 fc); 1529 1530/** 1531 * ieee80211_get_tkip_key - get a TKIP rc4 for skb 1532 * 1533 * This function computes a TKIP rc4 key for an skb. It computes 1534 * a phase 1 key if needed (iv16 wraps around). This function is to 1535 * be used by drivers which can do HW encryption but need to compute 1536 * to phase 1/2 key in SW. 1537 * 1538 * @keyconf: the parameter passed with the set key 1539 * @skb: the skb for which the key is needed 1540 * @rc4key: a buffer to which the key will be written 1541 */ 1542void ieee80211_get_tkip_key(struct ieee80211_key_conf *keyconf, 1543 struct sk_buff *skb, 1544 enum ieee80211_tkip_key_type type, u8 *key); 1545/** 1546 * ieee80211_wake_queue - wake specific queue 1547 * @hw: pointer as obtained from ieee80211_alloc_hw(). 1548 * @queue: queue number (counted from zero). 1549 * 1550 * Drivers should use this function instead of netif_wake_queue. 1551 */ 1552void ieee80211_wake_queue(struct ieee80211_hw *hw, int queue); 1553 1554/** 1555 * ieee80211_stop_queue - stop specific queue 1556 * @hw: pointer as obtained from ieee80211_alloc_hw(). 1557 * @queue: queue number (counted from zero). 1558 * 1559 * Drivers should use this function instead of netif_stop_queue. 1560 */ 1561void ieee80211_stop_queue(struct ieee80211_hw *hw, int queue); 1562 1563/** 1564 * ieee80211_stop_queues - stop all queues 1565 * @hw: pointer as obtained from ieee80211_alloc_hw(). 1566 * 1567 * Drivers should use this function instead of netif_stop_queue. 1568 */ 1569void ieee80211_stop_queues(struct ieee80211_hw *hw); 1570 1571/** 1572 * ieee80211_wake_queues - wake all queues 1573 * @hw: pointer as obtained from ieee80211_alloc_hw(). 1574 * 1575 * Drivers should use this function instead of netif_wake_queue. 1576 */ 1577void ieee80211_wake_queues(struct ieee80211_hw *hw); 1578 1579/** 1580 * ieee80211_scan_completed - completed hardware scan 1581 * 1582 * When hardware scan offload is used (i.e. the hw_scan() callback is 1583 * assigned) this function needs to be called by the driver to notify 1584 * mac80211 that the scan finished. 1585 * 1586 * @hw: the hardware that finished the scan 1587 */ 1588void ieee80211_scan_completed(struct ieee80211_hw *hw); 1589 1590/** 1591 * ieee80211_iterate_active_interfaces - iterate active interfaces 1592 * 1593 * This function iterates over the interfaces associated with a given 1594 * hardware that are currently active and calls the callback for them. 1595 * 1596 * @hw: the hardware struct of which the interfaces should be iterated over 1597 * @iterator: the iterator function to call, cannot sleep 1598 * @data: first argument of the iterator function 1599 */ 1600void ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw, 1601 void (*iterator)(void *data, u8 *mac, 1602 struct ieee80211_vif *vif), 1603 void *data); 1604 1605/** 1606 * ieee80211_start_tx_ba_session - Start a tx Block Ack session. 1607 * @hw: pointer as obtained from ieee80211_alloc_hw(). 1608 * @ra: receiver address of the BA session recipient 1609 * @tid: the TID to BA on. 1610 * @return: success if addBA request was sent, failure otherwise 1611 * 1612 * Although mac80211/low level driver/user space application can estimate 1613 * the need to start aggregation on a certain RA/TID, the session level 1614 * will be managed by the mac80211. 1615 */ 1616int ieee80211_start_tx_ba_session(struct ieee80211_hw *hw, u8 *ra, u16 tid); 1617 1618/** 1619 * ieee80211_start_tx_ba_cb - low level driver ready to aggregate. 1620 * @hw: pointer as obtained from ieee80211_alloc_hw(). 1621 * @ra: receiver address of the BA session recipient. 1622 * @tid: the TID to BA on. 1623 * 1624 * This function must be called by low level driver once it has 1625 * finished with preparations for the BA session. 1626 */ 1627void ieee80211_start_tx_ba_cb(struct ieee80211_hw *hw, u8 *ra, u16 tid); 1628 1629/** 1630 * ieee80211_start_tx_ba_cb_irqsafe - low level driver ready to aggregate. 1631 * @hw: pointer as obtained from ieee80211_alloc_hw(). 1632 * @ra: receiver address of the BA session recipient. 1633 * @tid: the TID to BA on. 1634 * 1635 * This function must be called by low level driver once it has 1636 * finished with preparations for the BA session. 1637 * This version of the function is irq safe. 1638 */ 1639void ieee80211_start_tx_ba_cb_irqsafe(struct ieee80211_hw *hw, const u8 *ra, 1640 u16 tid); 1641 1642/** 1643 * ieee80211_stop_tx_ba_session - Stop a Block Ack session. 1644 * @hw: pointer as obtained from ieee80211_alloc_hw(). 1645 * @ra: receiver address of the BA session recipient 1646 * @tid: the TID to stop BA. 1647 * @initiator: if indicates initiator DELBA frame will be sent. 1648 * @return: error if no sta with matching da found, success otherwise 1649 * 1650 * Although mac80211/low level driver/user space application can estimate 1651 * the need to stop aggregation on a certain RA/TID, the session level 1652 * will be managed by the mac80211. 1653 */ 1654int ieee80211_stop_tx_ba_session(struct ieee80211_hw *hw, 1655 u8 *ra, u16 tid, 1656 enum ieee80211_back_parties initiator); 1657 1658/** 1659 * ieee80211_stop_tx_ba_cb - low level driver ready to stop aggregate. 1660 * @hw: pointer as obtained from ieee80211_alloc_hw(). 1661 * @ra: receiver address of the BA session recipient. 1662 * @tid: the desired TID to BA on. 1663 * 1664 * This function must be called by low level driver once it has 1665 * finished with preparations for the BA session tear down. 1666 */ 1667void ieee80211_stop_tx_ba_cb(struct ieee80211_hw *hw, u8 *ra, u8 tid); 1668 1669/** 1670 * ieee80211_stop_tx_ba_cb_irqsafe - low level driver ready to stop aggregate. 1671 * @hw: pointer as obtained from ieee80211_alloc_hw(). 1672 * @ra: receiver address of the BA session recipient. 1673 * @tid: the desired TID to BA on. 1674 * 1675 * This function must be called by low level driver once it has 1676 * finished with preparations for the BA session tear down. 1677 * This version of the function is irq safe. 1678 */ 1679void ieee80211_stop_tx_ba_cb_irqsafe(struct ieee80211_hw *hw, const u8 *ra, 1680 u16 tid); 1681 1682/** 1683 * ieee80211_notify_mac - low level driver notification 1684 * @hw: pointer as obtained from ieee80211_alloc_hw(). 1685 * @notification_types: enum ieee80211_notification_types 1686 * 1687 * This function must be called by low level driver to inform mac80211 of 1688 * low level driver status change or force mac80211 to re-assoc for low 1689 * level driver internal error that require re-assoc. 1690 */ 1691void ieee80211_notify_mac(struct ieee80211_hw *hw, 1692 enum ieee80211_notification_types notif_type); 1693#endif /* MAC80211_H */ 1694