Searched refs:IRQ (Results 1 - 17 of 17) sorted by relevance

/drivers/pnp/
H A DKconfig11 peripherals to be configured by software, e.g. assign IRQ's or other
/drivers/misc/iwmc3200top/
H A Dmain.c195 LOG_TRACE(priv, IRQ, "enter iwmct_irq_read_worker %p\n", ws);
203 LOG_ERROR(priv, IRQ, "read_req_list empty in read worker\n");
216 LOG_ERROR(priv, IRQ, "kzalloc error, buf size %d\n", iosize);
220 LOG_INFO(priv, IRQ, "iosize=%d, buf=%p, func=%d\n",
226 LOG_ERROR(priv, IRQ, "error %d reading buffer\n", ret);
230 LOG_HEXDUMP(IRQ, (u8 *)buf, iosize);
244 LOG_WARNING(priv, IRQ,
261 LOG_ERROR(priv, IRQ,
268 LOG_INFO(priv, IRQ, "ACK barker arrived "
271 LOG_INFO(priv, IRQ, "Receive
[all...]
/drivers/pci/
H A DKconfig16 PCI bus instead of asserting a device IRQ pin.
/drivers/spi/
H A Dspi-s3c24xx-fiq.S28 @ fiq_rirq The base of the IRQ registers to find S3C2410_SRCPND
55 @@ set IRQ controller so that next op will trigger IRQ
/drivers/scsi/
H A Deata_pio.c645 buf->IRQ = ISAirqs[z];
662 printk("IRQ:%d IRQT:%d FORCADR:%d MCH:%d RIDQ:%d\n", gc->IRQ, gc->IRQ_TR, gc->FORCADR, gc->MAX_CHAN, gc->ID_qest);
709 if ((buff = get_pio_board_data(base, gc->IRQ, gc->scsi_id[3], cplen = (cpu_to_be32(gc->cplen) + 1) / 2, cppadlen = (cpu_to_be16(gc->cppadlen) + 1) / 2)) == NULL) {
725 if (!reg_IRQ[gc->IRQ]) { /* Interrupt already registered ? */
726 if (!request_irq(gc->IRQ, do_eata_pio_int_handler, IRQF_DISABLED, "EATA-PIO", sh)) {
727 reg_IRQ[gc->IRQ]++;
729 reg_IRQL[gc->IRQ] = 1; /* IRQ is edge triggered */
731 printk("Couldn't allocate IRQ
[all...]
H A Deata_generic.h141 #define HA_AIRQ 0x02 /* aux IRQ pending bit */
237 __u8 IRQ:4, /* IRQ used this HA */ member in struct:get_conf
238 IRQ_TR:1, /* IRQ Trigger: 0=edge, 1=level */
/drivers/staging/comedi/drivers/
H A Ddas6402.c68 #define IRQ (0x04 << 4) /* these two are */ macro
250 outb_p(IRQ | CONVSRC | BURSTEN | INTE, dev->iobase + 9);
284 b = IRQ | CONVSRC | BURSTEN | INTE;
H A Ddas800.c38 [1] - IRQ (optional, required for timed or externally triggered conversions)
41 IRQ can be omitted, although the cmd interface will not work without it.
95 #define IRQ 0x8 macro
380 if (!(status & IRQ))
497 /* grab our IRQ */
/drivers/tty/serial/8250/
H A DKconfig223 serial ports on the same board to share a single IRQ. To enable
227 bool "Autodetect IRQ on standard ports (unsafe)"
230 Say Y here if you want the kernel to try to guess which IRQ
233 This is considered unsafe; it is far better to configure the IRQ in
/drivers/misc/
H A DKconfig255 MFGPTs on the CS5535 require an interrupt. The selected IRQ
258 want to use a different IRQ by default. This is here for
/drivers/mmc/host/
H A DKconfig408 bool "Hardware support for SDIO IRQ"
/drivers/pci/hotplug/
H A Dcpqphp_ctrl.c891 irqreturn_t cpqhp_ctrl_intr(int IRQ, void *data) argument
2374 u8 IRQ = 0; local
2473 /* set up the IRQ info */
2803 /* We should be configuring an IRQ and the bridge's base address
2944 IRQ = resources->irqs->interrupt[(temp_byte +
2947 /* Program IRQ based on card type */
2951 IRQ = cpqhp_disk_irq;
2953 IRQ = cpqhp_nic_irq;
2956 /* IRQ Line */
2957 rc = pci_bus_write_config_byte (pci_bus, devfn, PCI_INTERRUPT_LINE, IRQ);
[all...]
H A Dcpqphp.h414 extern irqreturn_t cpqhp_ctrl_intr(int IRQ, void *data);
/drivers/net/ethernet/i825xx/
H A Dlp486e.c492 #define IRQ 10 /* default IRQ - can be changed by ECU */ macro
848 printk(KERN_ERR "%s: IRQ %d not free\n", dev->name, dev->irq);
991 dev->irq = IRQ;
1017 printk("%s: lp486e 82596 at %#3lx, IRQ %d,",
1296 static int irq = IRQ;
/drivers/dma/
H A DKconfig141 number of IRQ slots and map them dynamically to specific sources.
/drivers/ide/
H A DKconfig211 Also, currently, IDE generic doesn't allow IRQ sharing
/drivers/mfd/
H A DKconfig223 This core driver provides register access and IRQ handling
577 This core driver provides register access and IRQ handling
826 bool "Support for Qualcomm PM8xxx IRQ features"
830 This is the IRQ driver for Qualcomm PM 8xxx PMIC chips.

Completed in 733 milliseconds