pata_hpt366.c revision 0d5ff566779f894ca9937231a181eb31e4adff0e 
1/*
2 * Libata driver for the highpoint 366 and 368 UDMA66 ATA controllers.
3 *
4 * This driver is heavily based upon:
5 *
6 * linux/drivers/ide/pci/hpt366.c		Version 0.36	April 25, 2003
7 *
8 * Copyright (C) 1999-2003		Andre Hedrick <andre@linux-ide.org>
9 * Portions Copyright (C) 2001	        Sun Microsystems, Inc.
10 * Portions Copyright (C) 2003		Red Hat Inc
11 *
12 *
13 * TODO
14 *	Maybe PLL mode
15 *	Look into engine reset on timeout errors. Should not be
16 *		required.
17 */
18
19
20#include <linux/kernel.h>
21#include <linux/module.h>
22#include <linux/pci.h>
23#include <linux/init.h>
24#include <linux/blkdev.h>
25#include <linux/delay.h>
26#include <scsi/scsi_host.h>
27#include <linux/libata.h>
28
29#define DRV_NAME	"pata_hpt366"
30#define DRV_VERSION	"0.5.3"
31
32struct hpt_clock {
33	u8	xfer_speed;
34	u32	timing;
35};
36
37/* key for bus clock timings
38 * bit
39 * 0:3    data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW
40 *        DMA. cycles = value + 1
41 * 4:8    data_low_time. active time of DIOW_/DIOR_ for PIO and MW
42 *        DMA. cycles = value + 1
43 * 9:12   cmd_high_time. inactive time of DIOW_/DIOR_ during task file
44 *        register access.
45 * 13:17  cmd_low_time. active time of DIOW_/DIOR_ during task file
46 *        register access.
47 * 18:21  udma_cycle_time. clock freq and clock cycles for UDMA xfer.
48 *        during task file register access.
49 * 22:24  pre_high_time. time to initialize 1st cycle for PIO and MW DMA
50 *        xfer.
51 * 25:27  cmd_pre_high_time. time to initialize 1st PIO cycle for task
52 *        register access.
53 * 28     UDMA enable
54 * 29     DMA enable
55 * 30     PIO_MST enable. if set, the chip is in bus master mode during
56 *        PIO.
57 * 31     FIFO enable.
58 */
59
60static const struct hpt_clock hpt366_40[] = {
61	{	XFER_UDMA_4,	0x900fd943	},
62	{	XFER_UDMA_3,	0x900ad943	},
63	{	XFER_UDMA_2,	0x900bd943	},
64	{	XFER_UDMA_1,	0x9008d943	},
65	{	XFER_UDMA_0,	0x9008d943	},
66
67	{	XFER_MW_DMA_2,	0xa008d943	},
68	{	XFER_MW_DMA_1,	0xa010d955	},
69	{	XFER_MW_DMA_0,	0xa010d9fc	},
70
71	{	XFER_PIO_4,	0xc008d963	},
72	{	XFER_PIO_3,	0xc010d974	},
73	{	XFER_PIO_2,	0xc010d997	},
74	{	XFER_PIO_1,	0xc010d9c7	},
75	{	XFER_PIO_0,	0xc018d9d9	},
76	{	0,		0x0120d9d9	}
77};
78
79static const struct hpt_clock hpt366_33[] = {
80	{	XFER_UDMA_4,	0x90c9a731	},
81	{	XFER_UDMA_3,	0x90cfa731	},
82	{	XFER_UDMA_2,	0x90caa731	},
83	{	XFER_UDMA_1,	0x90cba731	},
84	{	XFER_UDMA_0,	0x90c8a731	},
85
86	{	XFER_MW_DMA_2,	0xa0c8a731	},
87	{	XFER_MW_DMA_1,	0xa0c8a732	},	/* 0xa0c8a733 */
88	{	XFER_MW_DMA_0,	0xa0c8a797	},
89
90	{	XFER_PIO_4,	0xc0c8a731	},
91	{	XFER_PIO_3,	0xc0c8a742	},
92	{	XFER_PIO_2,	0xc0d0a753	},
93	{	XFER_PIO_1,	0xc0d0a7a3	},	/* 0xc0d0a793 */
94	{	XFER_PIO_0,	0xc0d0a7aa	},	/* 0xc0d0a7a7 */
95	{	0,		0x0120a7a7	}
96};
97
98static const struct hpt_clock hpt366_25[] = {
99	{	XFER_UDMA_4,	0x90c98521	},
100	{	XFER_UDMA_3,	0x90cf8521	},
101	{	XFER_UDMA_2,	0x90cf8521	},
102	{	XFER_UDMA_1,	0x90cb8521	},
103	{	XFER_UDMA_0,	0x90cb8521	},
104
105	{	XFER_MW_DMA_2,	0xa0ca8521	},
106	{	XFER_MW_DMA_1,	0xa0ca8532	},
107	{	XFER_MW_DMA_0,	0xa0ca8575	},
108
109	{	XFER_PIO_4,	0xc0ca8521	},
110	{	XFER_PIO_3,	0xc0ca8532	},
111	{	XFER_PIO_2,	0xc0ca8542	},
112	{	XFER_PIO_1,	0xc0d08572	},
113	{	XFER_PIO_0,	0xc0d08585	},
114	{	0,		0x01208585	}
115};
116
117static const char *bad_ata33[] = {
118	"Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3", "Maxtor 90845U3", "Maxtor 90650U2",
119	"Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5", "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2",
120	"Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6", "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4",
121	"Maxtor 90510D4",
122	"Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2",
123	"Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7", "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4",
124	"Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5", "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2",
125	NULL
126};
127
128static const char *bad_ata66_4[] = {
129	"IBM-DTLA-307075",
130	"IBM-DTLA-307060",
131	"IBM-DTLA-307045",
132	"IBM-DTLA-307030",
133	"IBM-DTLA-307020",
134	"IBM-DTLA-307015",
135	"IBM-DTLA-305040",
136	"IBM-DTLA-305030",
137	"IBM-DTLA-305020",
138	"IC35L010AVER07-0",
139	"IC35L020AVER07-0",
140	"IC35L030AVER07-0",
141	"IC35L040AVER07-0",
142	"IC35L060AVER07-0",
143	"WDC AC310200R",
144	NULL
145};
146
147static const char *bad_ata66_3[] = {
148	"WDC AC310200R",
149	NULL
150};
151
152static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr, const char *list[])
153{
154	unsigned char model_num[ATA_ID_PROD_LEN + 1];
155	int i = 0;
156
157	ata_id_c_string(dev->id, model_num, ATA_ID_PROD, sizeof(model_num));
158
159	while (list[i] != NULL) {
160		if (!strcmp(list[i], model_num)) {
161			printk(KERN_WARNING DRV_NAME ": %s is not supported for %s.\n",
162				modestr, list[i]);
163			return 1;
164		}
165		i++;
166	}
167	return 0;
168}
169
170/**
171 *	hpt366_filter	-	mode selection filter
172 *	@ap: ATA interface
173 *	@adev: ATA device
174 *
175 *	Block UDMA on devices that cause trouble with this controller.
176 */
177
178static unsigned long hpt366_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask)
179{
180	if (adev->class == ATA_DEV_ATA) {
181		if (hpt_dma_blacklisted(adev, "UDMA",  bad_ata33))
182			mask &= ~ATA_MASK_UDMA;
183		if (hpt_dma_blacklisted(adev, "UDMA3", bad_ata66_3))
184			mask &= ~(0x07 << ATA_SHIFT_UDMA);
185		if (hpt_dma_blacklisted(adev, "UDMA4", bad_ata66_4))
186			mask &= ~(0x0F << ATA_SHIFT_UDMA);
187	}
188	return ata_pci_default_filter(ap, adev, mask);
189}
190
191/**
192 *	hpt36x_find_mode	-	reset the hpt36x bus
193 *	@ap: ATA port
194 *	@speed: transfer mode
195 *
196 *	Return the 32bit register programming information for this channel
197 *	that matches the speed provided.
198 */
199
200static u32 hpt36x_find_mode(struct ata_port *ap, int speed)
201{
202	struct hpt_clock *clocks = ap->host->private_data;
203
204	while(clocks->xfer_speed) {
205		if (clocks->xfer_speed == speed)
206			return clocks->timing;
207		clocks++;
208	}
209	BUG();
210	return 0xffffffffU;	/* silence compiler warning */
211}
212
213static int hpt36x_pre_reset(struct ata_port *ap)
214{
215	static const struct pci_bits hpt36x_enable_bits[] = {
216		{ 0x50, 1, 0x04, 0x04 },
217		{ 0x54, 1, 0x04, 0x04 }
218	};
219
220	u8 ata66;
221	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
222
223	if (!pci_test_config_bits(pdev, &hpt36x_enable_bits[ap->port_no]))
224		return -ENOENT;
225
226	pci_read_config_byte(pdev, 0x5A, &ata66);
227	if (ata66 & (1 << ap->port_no))
228		ap->cbl = ATA_CBL_PATA40;
229	else
230		ap->cbl = ATA_CBL_PATA80;
231	return ata_std_prereset(ap);
232}
233
234/**
235 *	hpt36x_error_handler	-	reset the hpt36x bus
236 *	@ap: ATA port to reset
237 *
238 *	Perform the reset handling for the 366/368
239 */
240
241static void hpt36x_error_handler(struct ata_port *ap)
242{
243	ata_bmdma_drive_eh(ap, hpt36x_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
244}
245
246/**
247 *	hpt366_set_piomode		-	PIO setup
248 *	@ap: ATA interface
249 *	@adev: device on the interface
250 *
251 *	Perform PIO mode setup.
252 */
253
254static void hpt366_set_piomode(struct ata_port *ap, struct ata_device *adev)
255{
256	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
257	u32 addr1, addr2;
258	u32 reg;
259	u32 mode;
260	u8 fast;
261
262	addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
263	addr2 = 0x51 + 4 * ap->port_no;
264
265	/* Fast interrupt prediction disable, hold off interrupt disable */
266	pci_read_config_byte(pdev, addr2, &fast);
267	if (fast & 0x80) {
268		fast &= ~0x80;
269		pci_write_config_byte(pdev, addr2, fast);
270	}
271
272	pci_read_config_dword(pdev, addr1, &reg);
273	mode = hpt36x_find_mode(ap, adev->pio_mode);
274	mode &= ~0x8000000;	/* No FIFO in PIO */
275	mode &= ~0x30070000;	/* Leave config bits alone */
276	reg &= 0x30070000;	/* Strip timing bits */
277	pci_write_config_dword(pdev, addr1, reg | mode);
278}
279
280/**
281 *	hpt366_set_dmamode		-	DMA timing setup
282 *	@ap: ATA interface
283 *	@adev: Device being configured
284 *
285 *	Set up the channel for MWDMA or UDMA modes. Much the same as with
286 *	PIO, load the mode number and then set MWDMA or UDMA flag.
287 */
288
289static void hpt366_set_dmamode(struct ata_port *ap, struct ata_device *adev)
290{
291	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
292	u32 addr1, addr2;
293	u32 reg;
294	u32 mode;
295	u8 fast;
296
297	addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
298	addr2 = 0x51 + 4 * ap->port_no;
299
300	/* Fast interrupt prediction disable, hold off interrupt disable */
301	pci_read_config_byte(pdev, addr2, &fast);
302	if (fast & 0x80) {
303		fast &= ~0x80;
304		pci_write_config_byte(pdev, addr2, fast);
305	}
306
307	pci_read_config_dword(pdev, addr1, &reg);
308	mode = hpt36x_find_mode(ap, adev->dma_mode);
309	mode |= 0x8000000;	/* FIFO in MWDMA or UDMA */
310	mode &= ~0xC0000000;	/* Leave config bits alone */
311	reg &= 0xC0000000;	/* Strip timing bits */
312	pci_write_config_dword(pdev, addr1, reg | mode);
313}
314
315static struct scsi_host_template hpt36x_sht = {
316	.module			= THIS_MODULE,
317	.name			= DRV_NAME,
318	.ioctl			= ata_scsi_ioctl,
319	.queuecommand		= ata_scsi_queuecmd,
320	.can_queue		= ATA_DEF_QUEUE,
321	.this_id		= ATA_SHT_THIS_ID,
322	.sg_tablesize		= LIBATA_MAX_PRD,
323	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
324	.emulated		= ATA_SHT_EMULATED,
325	.use_clustering		= ATA_SHT_USE_CLUSTERING,
326	.proc_name		= DRV_NAME,
327	.dma_boundary		= ATA_DMA_BOUNDARY,
328	.slave_configure	= ata_scsi_slave_config,
329	.slave_destroy		= ata_scsi_slave_destroy,
330	.bios_param		= ata_std_bios_param,
331	.resume			= ata_scsi_device_resume,
332	.suspend		= ata_scsi_device_suspend,
333};
334
335/*
336 *	Configuration for HPT366/68
337 */
338
339static struct ata_port_operations hpt366_port_ops = {
340	.port_disable	= ata_port_disable,
341	.set_piomode	= hpt366_set_piomode,
342	.set_dmamode	= hpt366_set_dmamode,
343	.mode_filter	= hpt366_filter,
344
345	.tf_load	= ata_tf_load,
346	.tf_read	= ata_tf_read,
347	.check_status 	= ata_check_status,
348	.exec_command	= ata_exec_command,
349	.dev_select 	= ata_std_dev_select,
350
351	.freeze		= ata_bmdma_freeze,
352	.thaw		= ata_bmdma_thaw,
353	.error_handler	= hpt36x_error_handler,
354	.post_internal_cmd = ata_bmdma_post_internal_cmd,
355
356	.bmdma_setup 	= ata_bmdma_setup,
357	.bmdma_start 	= ata_bmdma_start,
358	.bmdma_stop	= ata_bmdma_stop,
359	.bmdma_status 	= ata_bmdma_status,
360
361	.qc_prep 	= ata_qc_prep,
362	.qc_issue	= ata_qc_issue_prot,
363
364	.data_xfer	= ata_data_xfer,
365
366	.irq_handler	= ata_interrupt,
367	.irq_clear	= ata_bmdma_irq_clear,
368
369	.port_start	= ata_port_start,
370};
371
372/**
373 *	hpt36x_init_chipset	-	common chip setup
374 *	@dev: PCI device
375 *
376 *	Perform the chip setup work that must be done at both init and
377 *	resume time
378 */
379
380static void hpt36x_init_chipset(struct pci_dev *dev)
381{
382	u8 drive_fast;
383	pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
384	pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
385	pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
386	pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
387
388	pci_read_config_byte(dev, 0x51, &drive_fast);
389	if (drive_fast & 0x80)
390		pci_write_config_byte(dev, 0x51, drive_fast & ~0x80);
391}
392
393/**
394 *	hpt36x_init_one		-	Initialise an HPT366/368
395 *	@dev: PCI device
396 *	@id: Entry in match table
397 *
398 *	Initialise an HPT36x device. There are some interesting complications
399 *	here. Firstly the chip may report 366 and be one of several variants.
400 *	Secondly all the timings depend on the clock for the chip which we must
401 *	detect and look up
402 *
403 *	This is the known chip mappings. It may be missing a couple of later
404 *	releases.
405 *
406 *	Chip version		PCI		Rev	Notes
407 *	HPT366			4 (HPT366)	0	UDMA66
408 *	HPT366			4 (HPT366)	1	UDMA66
409 *	HPT368			4 (HPT366)	2	UDMA66
410 *	HPT37x/30x		4 (HPT366)	3+	Other driver
411 *
412 */
413
414static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
415{
416	static struct ata_port_info info_hpt366 = {
417		.sht = &hpt36x_sht,
418		.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
419		.pio_mask = 0x1f,
420		.mwdma_mask = 0x07,
421		.udma_mask = 0x1f,
422		.port_ops = &hpt366_port_ops
423	};
424	struct ata_port_info *port_info[2] = {&info_hpt366, &info_hpt366};
425
426	u32 class_rev;
427	u32 reg1;
428
429	pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
430	class_rev &= 0xFF;
431
432	/* May be a later chip in disguise. Check */
433	/* Newer chips are not in the HPT36x driver. Ignore them */
434	if (class_rev > 2)
435			return -ENODEV;
436
437	hpt36x_init_chipset(dev);
438
439	pci_read_config_dword(dev, 0x40,  &reg1);
440
441	/* PCI clocking determines the ATA timing values to use */
442	/* info_hpt366 is safe against re-entry so we can scribble on it */
443	switch((reg1 & 0x700) >> 8) {
444		case 5:
445			info_hpt366.private_data = &hpt366_40;
446			break;
447		case 9:
448			info_hpt366.private_data = &hpt366_25;
449			break;
450		default:
451			info_hpt366.private_data = &hpt366_33;
452			break;
453	}
454	/* Now kick off ATA set up */
455	return ata_pci_init_one(dev, port_info, 2);
456}
457
458static int hpt36x_reinit_one(struct pci_dev *dev)
459{
460	hpt36x_init_chipset(dev);
461	return ata_pci_device_resume(dev);
462}
463
464
465static const struct pci_device_id hpt36x[] = {
466	{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), },
467	{ },
468};
469
470static struct pci_driver hpt36x_pci_driver = {
471	.name 		= DRV_NAME,
472	.id_table	= hpt36x,
473	.probe 		= hpt36x_init_one,
474	.remove		= ata_pci_remove_one,
475	.suspend	= ata_pci_device_suspend,
476	.resume		= hpt36x_reinit_one,
477};
478
479static int __init hpt36x_init(void)
480{
481	return pci_register_driver(&hpt36x_pci_driver);
482}
483
484static void __exit hpt36x_exit(void)
485{
486	pci_unregister_driver(&hpt36x_pci_driver);
487}
488
489MODULE_AUTHOR("Alan Cox");
490MODULE_DESCRIPTION("low-level driver for the Highpoint HPT366/368");
491MODULE_LICENSE("GPL");
492MODULE_DEVICE_TABLE(pci, hpt36x);
493MODULE_VERSION(DRV_VERSION);
494
495module_init(hpt36x_init);
496module_exit(hpt36x_exit);
497