pata_serverworks.c revision 81ad1837b590775336f68eafcae8dab13a975b3a
1/* 2 * pata_serverworks.c - Serverworks PATA for new ATA layer 3 * (C) 2005 Red Hat Inc 4 * Alan Cox <alan@redhat.com> 5 * 6 * based upon 7 * 8 * serverworks.c 9 * 10 * Copyright (C) 1998-2000 Michel Aubry 11 * Copyright (C) 1998-2000 Andrzej Krzysztofowicz 12 * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org> 13 * Portions copyright (c) 2001 Sun Microsystems 14 * 15 * 16 * RCC/ServerWorks IDE driver for Linux 17 * 18 * OSB4: `Open South Bridge' IDE Interface (fn 1) 19 * supports UDMA mode 2 (33 MB/s) 20 * 21 * CSB5: `Champion South Bridge' IDE Interface (fn 1) 22 * all revisions support UDMA mode 4 (66 MB/s) 23 * revision A2.0 and up support UDMA mode 5 (100 MB/s) 24 * 25 * *** The CSB5 does not provide ANY register *** 26 * *** to detect 80-conductor cable presence. *** 27 * 28 * CSB6: `Champion South Bridge' IDE Interface (optional: third channel) 29 * 30 * Documentation: 31 * Available under NDA only. Errata info very hard to get. 32 */ 33 34#include <linux/kernel.h> 35#include <linux/module.h> 36#include <linux/pci.h> 37#include <linux/init.h> 38#include <linux/blkdev.h> 39#include <linux/delay.h> 40#include <scsi/scsi_host.h> 41#include <linux/libata.h> 42 43#define DRV_NAME "pata_serverworks" 44#define DRV_VERSION "0.4.2" 45 46#define SVWKS_CSB5_REVISION_NEW 0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */ 47#define SVWKS_CSB6_REVISION 0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */ 48 49/* Seagate Barracuda ATA IV Family drives in UDMA mode 5 50 * can overrun their FIFOs when used with the CSB5 */ 51 52static const char *csb_bad_ata100[] = { 53 "ST320011A", 54 "ST340016A", 55 "ST360021A", 56 "ST380021A", 57 NULL 58}; 59 60/** 61 * dell_cable - Dell serverworks cable detection 62 * @ap: ATA port to do cable detect 63 * 64 * Dell hide the 40/80 pin select for their interfaces in the top two 65 * bits of the subsystem ID. 66 */ 67 68static int dell_cable(struct ata_port *ap) { 69 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 70 71 if (pdev->subsystem_device & (1 << (ap->port_no + 14))) 72 return ATA_CBL_PATA80; 73 return ATA_CBL_PATA40; 74} 75 76/** 77 * sun_cable - Sun Cobalt 'Alpine' cable detection 78 * @ap: ATA port to do cable select 79 * 80 * Cobalt CSB5 IDE hides the 40/80pin in the top two bits of the 81 * subsystem ID the same as dell. We could use one function but we may 82 * need to extend the Dell one in future 83 */ 84 85static int sun_cable(struct ata_port *ap) { 86 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 87 88 if (pdev->subsystem_device & (1 << (ap->port_no + 14))) 89 return ATA_CBL_PATA80; 90 return ATA_CBL_PATA40; 91} 92 93/** 94 * osb4_cable - OSB4 cable detect 95 * @ap: ATA port to check 96 * 97 * The OSB4 isn't UDMA66 capable so this is easy 98 */ 99 100static int osb4_cable(struct ata_port *ap) { 101 return ATA_CBL_PATA40; 102} 103 104/** 105 * csb4_cable - CSB5/6 cable detect 106 * @ap: ATA port to check 107 * 108 * Serverworks default arrangement is to use the drive side detection 109 * only. 110 */ 111 112static int csb_cable(struct ata_port *ap) { 113 return ATA_CBL_PATA80; 114} 115 116struct sv_cable_table { 117 int device; 118 int subvendor; 119 int (*cable_detect)(struct ata_port *ap); 120}; 121 122/* 123 * Note that we don't copy the old serverworks code because the old 124 * code contains obvious mistakes 125 */ 126 127static struct sv_cable_table cable_detect[] = { 128 { PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_VENDOR_ID_DELL, dell_cable }, 129 { PCI_DEVICE_ID_SERVERWORKS_CSB6IDE, PCI_VENDOR_ID_DELL, dell_cable }, 130 { PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_VENDOR_ID_SUN, sun_cable }, 131 { PCI_DEVICE_ID_SERVERWORKS_OSB4IDE, PCI_ANY_ID, osb4_cable }, 132 { PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_ANY_ID, csb_cable }, 133 { PCI_DEVICE_ID_SERVERWORKS_CSB6IDE, PCI_ANY_ID, csb_cable }, 134 { PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2, PCI_ANY_ID, csb_cable }, 135 { PCI_DEVICE_ID_SERVERWORKS_HT1000IDE, PCI_ANY_ID, csb_cable }, 136 { } 137}; 138 139/** 140 * serverworks_cable_detect - cable detection 141 * @ap: ATA port 142 * @deadline: deadline jiffies for the operation 143 * 144 * Perform cable detection according to the device and subvendor 145 * identifications 146 */ 147 148static int serverworks_cable_detect(struct ata_port *ap) 149{ 150 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 151 struct sv_cable_table *cb = cable_detect; 152 153 while(cb->device) { 154 if (cb->device == pdev->device && 155 (cb->subvendor == pdev->subsystem_vendor || 156 cb->subvendor == PCI_ANY_ID)) { 157 return cb->cable_detect(ap); 158 } 159 cb++; 160 } 161 162 BUG(); 163 return -1; /* kill compiler warning */ 164} 165 166/** 167 * serverworks_is_csb - Check for CSB or OSB 168 * @pdev: PCI device to check 169 * 170 * Returns true if the device being checked is known to be a CSB 171 * series device. 172 */ 173 174static u8 serverworks_is_csb(struct pci_dev *pdev) 175{ 176 switch (pdev->device) { 177 case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE: 178 case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE: 179 case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2: 180 case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE: 181 return 1; 182 default: 183 break; 184 } 185 return 0; 186} 187 188/** 189 * serverworks_osb4_filter - mode selection filter 190 * @adev: ATA device 191 * @mask: Mask of proposed modes 192 * 193 * Filter the offered modes for the device to apply controller 194 * specific rules. OSB4 requires no UDMA for disks due to a FIFO 195 * bug we hit. 196 */ 197 198static unsigned long serverworks_osb4_filter(struct ata_device *adev, unsigned long mask) 199{ 200 if (adev->class == ATA_DEV_ATA) 201 mask &= ~ATA_MASK_UDMA; 202 return ata_pci_default_filter(adev, mask); 203} 204 205 206/** 207 * serverworks_csb_filter - mode selection filter 208 * @adev: ATA device 209 * @mask: Mask of proposed modes 210 * 211 * Check the blacklist and disable UDMA5 if matched 212 */ 213 214static unsigned long serverworks_csb_filter(struct ata_device *adev, unsigned long mask) 215{ 216 const char *p; 217 char model_num[ATA_ID_PROD_LEN + 1]; 218 int i; 219 220 /* Disk, UDMA */ 221 if (adev->class != ATA_DEV_ATA) 222 return ata_pci_default_filter(adev, mask); 223 224 /* Actually do need to check */ 225 ata_id_c_string(adev->id, model_num, ATA_ID_PROD, sizeof(model_num)); 226 227 for (i = 0; (p = csb_bad_ata100[i]) != NULL; i++) { 228 if (!strcmp(p, model_num)) 229 mask &= ~(0x1F << ATA_SHIFT_UDMA); 230 } 231 return ata_pci_default_filter(adev, mask); 232} 233 234 235/** 236 * serverworks_set_piomode - set initial PIO mode data 237 * @ap: ATA interface 238 * @adev: ATA device 239 * 240 * Program the OSB4/CSB5 timing registers for PIO. The PIO register 241 * load is done as a simple lookup. 242 */ 243static void serverworks_set_piomode(struct ata_port *ap, struct ata_device *adev) 244{ 245 static const u8 pio_mode[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 }; 246 int offset = 1 + (2 * ap->port_no) - adev->devno; 247 int devbits = (2 * ap->port_no + adev->devno) * 4; 248 u16 csb5_pio; 249 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 250 int pio = adev->pio_mode - XFER_PIO_0; 251 252 pci_write_config_byte(pdev, 0x40 + offset, pio_mode[pio]); 253 254 /* The OSB4 just requires the timing but the CSB series want the 255 mode number as well */ 256 if (serverworks_is_csb(pdev)) { 257 pci_read_config_word(pdev, 0x4A, &csb5_pio); 258 csb5_pio &= ~(0x0F << devbits); 259 pci_write_config_byte(pdev, 0x4A, csb5_pio | (pio << devbits)); 260 } 261} 262 263/** 264 * serverworks_set_dmamode - set initial DMA mode data 265 * @ap: ATA interface 266 * @adev: ATA device 267 * 268 * Program the MWDMA/UDMA modes for the serverworks OSB4/CSB5 269 * chipset. The MWDMA mode values are pulled from a lookup table 270 * while the chipset uses mode number for UDMA. 271 */ 272 273static void serverworks_set_dmamode(struct ata_port *ap, struct ata_device *adev) 274{ 275 static const u8 dma_mode[] = { 0x77, 0x21, 0x20 }; 276 int offset = 1 + 2 * ap->port_no - adev->devno; 277 int devbits = (2 * ap->port_no + adev->devno); 278 u8 ultra; 279 u8 ultra_cfg; 280 struct pci_dev *pdev = to_pci_dev(ap->host->dev); 281 282 pci_read_config_byte(pdev, 0x54, &ultra_cfg); 283 284 if (adev->dma_mode >= XFER_UDMA_0) { 285 pci_write_config_byte(pdev, 0x44 + offset, 0x20); 286 287 pci_read_config_byte(pdev, 0x56 + ap->port_no, &ultra); 288 ultra &= ~(0x0F << (ap->port_no * 4)); 289 ultra |= (adev->dma_mode - XFER_UDMA_0) 290 << (ap->port_no * 4); 291 pci_write_config_byte(pdev, 0x56 + ap->port_no, ultra); 292 293 ultra_cfg |= (1 << devbits); 294 } else { 295 pci_write_config_byte(pdev, 0x44 + offset, 296 dma_mode[adev->dma_mode - XFER_MW_DMA_0]); 297 ultra_cfg &= ~(1 << devbits); 298 } 299 pci_write_config_byte(pdev, 0x54, ultra_cfg); 300} 301 302static struct scsi_host_template serverworks_sht = { 303 .module = THIS_MODULE, 304 .name = DRV_NAME, 305 .ioctl = ata_scsi_ioctl, 306 .queuecommand = ata_scsi_queuecmd, 307 .can_queue = ATA_DEF_QUEUE, 308 .this_id = ATA_SHT_THIS_ID, 309 .sg_tablesize = LIBATA_MAX_PRD, 310 .cmd_per_lun = ATA_SHT_CMD_PER_LUN, 311 .emulated = ATA_SHT_EMULATED, 312 .use_clustering = ATA_SHT_USE_CLUSTERING, 313 .proc_name = DRV_NAME, 314 .dma_boundary = ATA_DMA_BOUNDARY, 315 .slave_configure = ata_scsi_slave_config, 316 .slave_destroy = ata_scsi_slave_destroy, 317 .bios_param = ata_std_bios_param, 318}; 319 320static struct ata_port_operations serverworks_osb4_port_ops = { 321 .set_piomode = serverworks_set_piomode, 322 .set_dmamode = serverworks_set_dmamode, 323 .mode_filter = serverworks_osb4_filter, 324 325 .tf_load = ata_tf_load, 326 .tf_read = ata_tf_read, 327 .check_status = ata_check_status, 328 .exec_command = ata_exec_command, 329 .dev_select = ata_std_dev_select, 330 331 .freeze = ata_bmdma_freeze, 332 .thaw = ata_bmdma_thaw, 333 .error_handler = ata_bmdma_error_handler, 334 .post_internal_cmd = ata_bmdma_post_internal_cmd, 335 .cable_detect = serverworks_cable_detect, 336 337 .bmdma_setup = ata_bmdma_setup, 338 .bmdma_start = ata_bmdma_start, 339 .bmdma_stop = ata_bmdma_stop, 340 .bmdma_status = ata_bmdma_status, 341 342 .qc_prep = ata_qc_prep, 343 .qc_issue = ata_qc_issue_prot, 344 345 .data_xfer = ata_data_xfer, 346 347 .irq_handler = ata_interrupt, 348 .irq_clear = ata_bmdma_irq_clear, 349 .irq_on = ata_irq_on, 350 351 .port_start = ata_sff_port_start, 352}; 353 354static struct ata_port_operations serverworks_csb_port_ops = { 355 .set_piomode = serverworks_set_piomode, 356 .set_dmamode = serverworks_set_dmamode, 357 .mode_filter = serverworks_csb_filter, 358 359 .tf_load = ata_tf_load, 360 .tf_read = ata_tf_read, 361 .check_status = ata_check_status, 362 .exec_command = ata_exec_command, 363 .dev_select = ata_std_dev_select, 364 365 .freeze = ata_bmdma_freeze, 366 .thaw = ata_bmdma_thaw, 367 .error_handler = ata_bmdma_error_handler, 368 .post_internal_cmd = ata_bmdma_post_internal_cmd, 369 .cable_detect = serverworks_cable_detect, 370 371 .bmdma_setup = ata_bmdma_setup, 372 .bmdma_start = ata_bmdma_start, 373 .bmdma_stop = ata_bmdma_stop, 374 .bmdma_status = ata_bmdma_status, 375 376 .qc_prep = ata_qc_prep, 377 .qc_issue = ata_qc_issue_prot, 378 379 .data_xfer = ata_data_xfer, 380 381 .irq_handler = ata_interrupt, 382 .irq_clear = ata_bmdma_irq_clear, 383 .irq_on = ata_irq_on, 384 385 .port_start = ata_sff_port_start, 386}; 387 388static int serverworks_fixup_osb4(struct pci_dev *pdev) 389{ 390 u32 reg; 391 struct pci_dev *isa_dev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS, 392 PCI_DEVICE_ID_SERVERWORKS_OSB4, NULL); 393 if (isa_dev) { 394 pci_read_config_dword(isa_dev, 0x64, ®); 395 reg &= ~0x00002000; /* disable 600ns interrupt mask */ 396 if (!(reg & 0x00004000)) 397 printk(KERN_DEBUG DRV_NAME ": UDMA not BIOS enabled.\n"); 398 reg |= 0x00004000; /* enable UDMA/33 support */ 399 pci_write_config_dword(isa_dev, 0x64, reg); 400 pci_dev_put(isa_dev); 401 return 0; 402 } 403 printk(KERN_WARNING "ata_serverworks: Unable to find bridge.\n"); 404 return -ENODEV; 405} 406 407static int serverworks_fixup_csb(struct pci_dev *pdev) 408{ 409 u8 btr; 410 411 /* Third Channel Test */ 412 if (!(PCI_FUNC(pdev->devfn) & 1)) { 413 struct pci_dev * findev = NULL; 414 u32 reg4c = 0; 415 findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS, 416 PCI_DEVICE_ID_SERVERWORKS_CSB5, NULL); 417 if (findev) { 418 pci_read_config_dword(findev, 0x4C, ®4c); 419 reg4c &= ~0x000007FF; 420 reg4c |= 0x00000040; 421 reg4c |= 0x00000020; 422 pci_write_config_dword(findev, 0x4C, reg4c); 423 pci_dev_put(findev); 424 } 425 } else { 426 struct pci_dev * findev = NULL; 427 u8 reg41 = 0; 428 429 findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS, 430 PCI_DEVICE_ID_SERVERWORKS_CSB6, NULL); 431 if (findev) { 432 pci_read_config_byte(findev, 0x41, ®41); 433 reg41 &= ~0x40; 434 pci_write_config_byte(findev, 0x41, reg41); 435 pci_dev_put(findev); 436 } 437 } 438 /* setup the UDMA Control register 439 * 440 * 1. clear bit 6 to enable DMA 441 * 2. enable DMA modes with bits 0-1 442 * 00 : legacy 443 * 01 : udma2 444 * 10 : udma2/udma4 445 * 11 : udma2/udma4/udma5 446 */ 447 pci_read_config_byte(pdev, 0x5A, &btr); 448 btr &= ~0x40; 449 if (!(PCI_FUNC(pdev->devfn) & 1)) 450 btr |= 0x2; 451 else 452 btr |= (pdev->revision >= SVWKS_CSB5_REVISION_NEW) ? 0x3 : 0x2; 453 pci_write_config_byte(pdev, 0x5A, btr); 454 455 return btr; 456} 457 458static void serverworks_fixup_ht1000(struct pci_dev *pdev) 459{ 460 u8 btr; 461 /* Setup HT1000 SouthBridge Controller - Single Channel Only */ 462 pci_read_config_byte(pdev, 0x5A, &btr); 463 btr &= ~0x40; 464 btr |= 0x3; 465 pci_write_config_byte(pdev, 0x5A, btr); 466} 467 468 469static int serverworks_init_one(struct pci_dev *pdev, const struct pci_device_id *id) 470{ 471 static const struct ata_port_info info[4] = { 472 { /* OSB4 */ 473 .sht = &serverworks_sht, 474 .flags = ATA_FLAG_SLAVE_POSS, 475 .pio_mask = 0x1f, 476 .mwdma_mask = 0x07, 477 .udma_mask = 0x07, 478 .port_ops = &serverworks_osb4_port_ops 479 }, { /* OSB4 no UDMA */ 480 .sht = &serverworks_sht, 481 .flags = ATA_FLAG_SLAVE_POSS, 482 .pio_mask = 0x1f, 483 .mwdma_mask = 0x07, 484 .udma_mask = 0x00, 485 .port_ops = &serverworks_osb4_port_ops 486 }, { /* CSB5 */ 487 .sht = &serverworks_sht, 488 .flags = ATA_FLAG_SLAVE_POSS, 489 .pio_mask = 0x1f, 490 .mwdma_mask = 0x07, 491 .udma_mask = ATA_UDMA4, 492 .port_ops = &serverworks_csb_port_ops 493 }, { /* CSB5 - later revisions*/ 494 .sht = &serverworks_sht, 495 .flags = ATA_FLAG_SLAVE_POSS, 496 .pio_mask = 0x1f, 497 .mwdma_mask = 0x07, 498 .udma_mask = ATA_UDMA5, 499 .port_ops = &serverworks_csb_port_ops 500 } 501 }; 502 const struct ata_port_info *ppi[] = { &info[id->driver_data], NULL }; 503 504 /* Force master latency timer to 64 PCI clocks */ 505 pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x40); 506 507 /* OSB4 : South Bridge and IDE */ 508 if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) { 509 /* Select non UDMA capable OSB4 if we can't do fixups */ 510 if ( serverworks_fixup_osb4(pdev) < 0) 511 ppi[0] = &info[1]; 512 } 513 /* setup CSB5/CSB6 : South Bridge and IDE option RAID */ 514 else if ((pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) || 515 (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) || 516 (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) { 517 518 /* If the returned btr is the newer revision then 519 select the right info block */ 520 if (serverworks_fixup_csb(pdev) == 3) 521 ppi[0] = &info[3]; 522 523 /* Is this the 3rd channel CSB6 IDE ? */ 524 if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2) 525 ppi[1] = &ata_dummy_port_info; 526 } 527 /* setup HT1000E */ 528 else if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE) 529 serverworks_fixup_ht1000(pdev); 530 531 if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) 532 ata_pci_clear_simplex(pdev); 533 534 return ata_pci_init_one(pdev, ppi); 535} 536 537#ifdef CONFIG_PM 538static int serverworks_reinit_one(struct pci_dev *pdev) 539{ 540 /* Force master latency timer to 64 PCI clocks */ 541 pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x40); 542 543 switch (pdev->device) 544 { 545 case PCI_DEVICE_ID_SERVERWORKS_OSB4IDE: 546 serverworks_fixup_osb4(pdev); 547 break; 548 case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE: 549 ata_pci_clear_simplex(pdev); 550 /* fall through */ 551 case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE: 552 case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2: 553 serverworks_fixup_csb(pdev); 554 break; 555 case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE: 556 serverworks_fixup_ht1000(pdev); 557 break; 558 } 559 return ata_pci_device_resume(pdev); 560} 561#endif 562 563static const struct pci_device_id serverworks[] = { 564 { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE), 0}, 565 { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE), 2}, 566 { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE), 2}, 567 { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2), 2}, 568 { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE), 2}, 569 570 { }, 571}; 572 573static struct pci_driver serverworks_pci_driver = { 574 .name = DRV_NAME, 575 .id_table = serverworks, 576 .probe = serverworks_init_one, 577 .remove = ata_pci_remove_one, 578#ifdef CONFIG_PM 579 .suspend = ata_pci_device_suspend, 580 .resume = serverworks_reinit_one, 581#endif 582}; 583 584static int __init serverworks_init(void) 585{ 586 return pci_register_driver(&serverworks_pci_driver); 587} 588 589static void __exit serverworks_exit(void) 590{ 591 pci_unregister_driver(&serverworks_pci_driver); 592} 593 594MODULE_AUTHOR("Alan Cox"); 595MODULE_DESCRIPTION("low-level driver for Serverworks OSB4/CSB5/CSB6"); 596MODULE_LICENSE("GPL"); 597MODULE_DEVICE_TABLE(pci, serverworks); 598MODULE_VERSION(DRV_VERSION); 599 600module_init(serverworks_init); 601module_exit(serverworks_exit); 602