pcmmio.c revision da91b2692e0939b307f9047192d2b9fe07793e7a
1/* 2 comedi/drivers/pcmmio.c 3 Driver for Winsystems PC-104 based multifunction IO board. 4 5 COMEDI - Linux Control and Measurement Device Interface 6 Copyright (C) 2007 Calin A. Culianu <calin@ajvar.org> 7 8 This program is free software; you can redistribute it and/or modify 9 it under the terms of the GNU General Public License as published by 10 the Free Software Foundation; either version 2 of the License, or 11 (at your option) any later version. 12 13 This program is distributed in the hope that it will be useful, 14 but WITHOUT ANY WARRANTY; without even the implied warranty of 15 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 16 GNU General Public License for more details. 17 18 You should have received a copy of the GNU General Public License 19 along with this program; if not, write to the Free Software 20 Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. 21*/ 22/* 23Driver: pcmmio 24Description: A driver for the PCM-MIO multifunction board 25Devices: [Winsystems] PCM-MIO (pcmmio) 26Author: Calin Culianu <calin@ajvar.org> 27Updated: Wed, May 16 2007 16:21:10 -0500 28Status: works 29 30A driver for the relatively new PCM-MIO multifunction board from 31Winsystems. This board is a PC-104 based I/O board. It contains 32four subdevices: 33 subdevice 0 - 16 channels of 16-bit AI 34 subdevice 1 - 8 channels of 16-bit AO 35 subdevice 2 - first 24 channels of the 48 channel of DIO (with edge-triggered interrupt support) 36 subdevice 3 - last 24 channels of the 48 channel DIO (no interrupt support for this bank of channels) 37 38 Some notes: 39 40 Synchronous reads and writes are the only things implemented for AI and AO, 41 even though the hardware itself can do streaming acquisition, etc. Anyone 42 want to add asynchronous I/O for AI/AO as a feature? Be my guest... 43 44 Asynchronous I/O for the DIO subdevices *is* implemented, however! They are 45 basically edge-triggered interrupts for any configuration of the first 46 24 DIO-lines. 47 48 Also note that this interrupt support is untested. 49 50 A few words about edge-detection IRQ support (commands on DIO): 51 52 * To use edge-detection IRQ support for the DIO subdevice, pass the IRQ 53 of the board to the comedi_config command. The board IRQ is not jumpered 54 but rather configured through software, so any IRQ from 1-15 is OK. 55 56 * Due to the genericity of the comedi API, you need to create a special 57 comedi_command in order to use edge-triggered interrupts for DIO. 58 59 * Use comedi_commands with TRIG_NOW. Your callback will be called each 60 time an edge is detected on the specified DIO line(s), and the data 61 values will be two sample_t's, which should be concatenated to form 62 one 32-bit unsigned int. This value is the mask of channels that had 63 edges detected from your channel list. Note that the bits positions 64 in the mask correspond to positions in your chanlist when you 65 specified the command and *not* channel id's! 66 67 * To set the polarity of the edge-detection interrupts pass a nonzero value 68 for either CR_RANGE or CR_AREF for edge-up polarity, or a zero 69 value for both CR_RANGE and CR_AREF if you want edge-down polarity. 70 71Configuration Options: 72 [0] - I/O port base address 73 [1] - IRQ (optional -- for edge-detect interrupt support only, leave out if you don't need this feature) 74*/ 75 76#include "../comedidev.h" 77#include <linux/pci.h> /* for PCI devices */ 78 79#define MIN(a,b) ( ((a) < (b)) ? (a) : (b) ) 80 81/* This stuff is all from pcmuio.c -- it refers to the DIO subdevices only */ 82#define CHANS_PER_PORT 8 83#define PORTS_PER_ASIC 6 84#define INTR_PORTS_PER_ASIC 3 85#define MAX_CHANS_PER_SUBDEV 24 /* number of channels per comedi subdevice */ 86#define PORTS_PER_SUBDEV (MAX_CHANS_PER_SUBDEV/CHANS_PER_PORT) 87#define CHANS_PER_ASIC (CHANS_PER_PORT*PORTS_PER_ASIC) 88#define INTR_CHANS_PER_ASIC 24 89#define INTR_PORTS_PER_SUBDEV (INTR_CHANS_PER_ASIC/CHANS_PER_PORT) 90#define MAX_DIO_CHANS (PORTS_PER_ASIC*1*CHANS_PER_PORT) 91#define MAX_ASICS (MAX_DIO_CHANS/CHANS_PER_ASIC) 92#define SDEV_NO ((int)(s - dev->subdevices)) 93#define CALC_N_DIO_SUBDEVS(nchans) ((nchans)/MAX_CHANS_PER_SUBDEV + (!!((nchans)%MAX_CHANS_PER_SUBDEV)) /*+ (nchans > INTR_CHANS_PER_ASIC ? 2 : 1)*/) 94/* IO Memory sizes */ 95#define ASIC_IOSIZE (0x0B) 96#define PCMMIO48_IOSIZE ASIC_IOSIZE 97 98/* Some offsets - these are all in the 16byte IO memory offset from 99 the base address. Note that there is a paging scheme to swap out 100 offsets 0x8-0xA using the PAGELOCK register. See the table below. 101 102 Register(s) Pages R/W? Description 103 -------------------------------------------------------------- 104 REG_PORTx All R/W Read/Write/Configure IO 105 REG_INT_PENDING All ReadOnly Quickly see which INT_IDx has int. 106 REG_PAGELOCK All WriteOnly Select a page 107 REG_POLx Pg. 1 only WriteOnly Select edge-detection polarity 108 REG_ENABx Pg. 2 only WriteOnly Enable/Disable edge-detect. int. 109 REG_INT_IDx Pg. 3 only R/W See which ports/bits have ints. 110 */ 111#define REG_PORT0 0x0 112#define REG_PORT1 0x1 113#define REG_PORT2 0x2 114#define REG_PORT3 0x3 115#define REG_PORT4 0x4 116#define REG_PORT5 0x5 117#define REG_INT_PENDING 0x6 118#define REG_PAGELOCK 0x7 /* page selector register, upper 2 bits select a page 119 and bits 0-5 are used to 'lock down' a particular 120 port above to make it readonly. */ 121#define REG_POL0 0x8 122#define REG_POL1 0x9 123#define REG_POL2 0xA 124#define REG_ENAB0 0x8 125#define REG_ENAB1 0x9 126#define REG_ENAB2 0xA 127#define REG_INT_ID0 0x8 128#define REG_INT_ID1 0x9 129#define REG_INT_ID2 0xA 130 131#define NUM_PAGED_REGS 3 132#define NUM_PAGES 4 133#define FIRST_PAGED_REG 0x8 134#define REG_PAGE_BITOFFSET 6 135#define REG_LOCK_BITOFFSET 0 136#define REG_PAGE_MASK (~((0x1<<REG_PAGE_BITOFFSET)-1)) 137#define REG_LOCK_MASK ~(REG_PAGE_MASK) 138#define PAGE_POL 1 139#define PAGE_ENAB 2 140#define PAGE_INT_ID 3 141 142typedef int (*comedi_insn_fn_t) (struct comedi_device *, struct comedi_subdevice *, 143 struct comedi_insn *, unsigned int *); 144 145static int ai_rinsn(struct comedi_device *, struct comedi_subdevice *, struct comedi_insn *, 146 unsigned int *); 147static int ao_rinsn(struct comedi_device *, struct comedi_subdevice *, struct comedi_insn *, 148 unsigned int *); 149static int ao_winsn(struct comedi_device *, struct comedi_subdevice *, struct comedi_insn *, 150 unsigned int *); 151 152/* 153 * Board descriptions for two imaginary boards. Describing the 154 * boards in this way is optional, and completely driver-dependent. 155 * Some drivers use arrays such as this, other do not. 156 */ 157struct pcmmio_board { 158 const char *name; 159 const int dio_num_asics; 160 const int dio_num_ports; 161 const int total_iosize; 162 const int ai_bits; 163 const int ao_bits; 164 const int n_ai_chans; 165 const int n_ao_chans; 166 const struct comedi_lrange *ai_range_table, *ao_range_table; 167 comedi_insn_fn_t ai_rinsn, ao_rinsn, ao_winsn; 168}; 169 170static const struct comedi_lrange ranges_ai = 171 { 4, {RANGE(-5., 5.), RANGE(-10., 10.), RANGE(0., 5.), RANGE(0., 172 10.)} 173}; 174 175static const struct comedi_lrange ranges_ao = 176 { 6, {RANGE(0., 5.), RANGE(0., 10.), RANGE(-5., 5.), RANGE(-10., 10.), 177 RANGE(-2.5, 2.5), RANGE(-2.5, 7.5)} 178}; 179 180static const struct pcmmio_board pcmmio_boards[] = { 181 { 182 name: "pcmmio", 183 dio_num_asics:1, 184 dio_num_ports:6, 185 total_iosize:32, 186 ai_bits: 16, 187 ao_bits: 16, 188 n_ai_chans:16, 189 n_ao_chans:8, 190 ai_range_table:&ranges_ai, 191 ao_range_table:&ranges_ao, 192 ai_rinsn:ai_rinsn, 193 ao_rinsn:ao_rinsn, 194 ao_winsn:ao_winsn}, 195}; 196 197/* 198 * Useful for shorthand access to the particular board structure 199 */ 200#define thisboard ((const struct pcmmio_board *)dev->board_ptr) 201 202/* this structure is for data unique to this subdevice. */ 203struct pcmmio_subdev_private { 204 205 union { 206 /* for DIO: mapping of halfwords (bytes) in port/chanarray to iobase */ 207 unsigned long iobases[PORTS_PER_SUBDEV]; 208 209 /* for AI/AO */ 210 unsigned long iobase; 211 }; 212 union { 213 struct { 214 215 /* The below is only used for intr subdevices */ 216 struct { 217 int asic; /* if non-negative, this subdev has an interrupt asic */ 218 int first_chan; /* if nonnegative, the first channel id for 219 interrupts. */ 220 int num_asic_chans; /* the number of asic channels in this subdev 221 that have interrutps */ 222 int asic_chan; /* if nonnegative, the first channel id with 223 respect to the asic that has interrupts */ 224 int enabled_mask; /* subdev-relative channel mask for channels 225 we are interested in */ 226 int active; 227 int stop_count; 228 int continuous; 229 spinlock_t spinlock; 230 } intr; 231 } dio; 232 struct { 233 unsigned int shadow_samples[8]; /* the last unsigned int data written */ 234 } ao; 235 }; 236}; 237 238/* this structure is for data unique to this hardware driver. If 239 several hardware drivers keep similar information in this structure, 240 feel free to suggest moving the variable to the struct comedi_device struct. */ 241struct pcmmio_private { 242 /* stuff for DIO */ 243 struct { 244 unsigned char pagelock; /* current page and lock */ 245 unsigned char pol[NUM_PAGED_REGS]; /* shadow of POLx registers */ 246 unsigned char enab[NUM_PAGED_REGS]; /* shadow of ENABx registers */ 247 int num; 248 unsigned long iobase; 249 unsigned int irq; 250 spinlock_t spinlock; 251 } asics[MAX_ASICS]; 252 struct pcmmio_subdev_private *sprivs; 253}; 254 255/* 256 * most drivers define the following macro to make it easy to 257 * access the private structure. 258 */ 259#define devpriv ((struct pcmmio_private *)dev->private) 260#define subpriv ((struct pcmmio_subdev_private *)s->private) 261/* 262 * The struct comedi_driver structure tells the Comedi core module 263 * which functions to call to configure/deconfigure (attach/detach) 264 * the board, and also about the kernel module that contains 265 * the device code. 266 */ 267static int pcmmio_attach(struct comedi_device *dev, struct comedi_devconfig *it); 268static int pcmmio_detach(struct comedi_device *dev); 269 270static struct comedi_driver driver = { 271 driver_name:"pcmmio", 272 module:THIS_MODULE, 273 attach:pcmmio_attach, 274 detach:pcmmio_detach, 275/* It is not necessary to implement the following members if you are 276 * writing a driver for a ISA PnP or PCI card */ 277 /* Most drivers will support multiple types of boards by 278 * having an array of board structures. These were defined 279 * in pcmmio_boards[] above. Note that the element 'name' 280 * was first in the structure -- Comedi uses this fact to 281 * extract the name of the board without knowing any details 282 * about the structure except for its length. 283 * When a device is attached (by comedi_config), the name 284 * of the device is given to Comedi, and Comedi tries to 285 * match it by going through the list of board names. If 286 * there is a match, the address of the pointer is put 287 * into dev->board_ptr and driver->attach() is called. 288 * 289 * Note that these are not necessary if you can determine 290 * the type of board in software. ISA PnP, PCI, and PCMCIA 291 * devices are such boards. 292 */ 293 board_name:&pcmmio_boards[0].name, 294 offset:sizeof(struct pcmmio_board), 295 num_names:sizeof(pcmmio_boards) / sizeof(struct pcmmio_board), 296}; 297 298static int pcmmio_dio_insn_bits(struct comedi_device * dev, struct comedi_subdevice * s, 299 struct comedi_insn * insn, unsigned int * data); 300static int pcmmio_dio_insn_config(struct comedi_device * dev, struct comedi_subdevice * s, 301 struct comedi_insn * insn, unsigned int * data); 302 303static irqreturn_t interrupt_pcmmio(int irq, void *d); 304static void pcmmio_stop_intr(struct comedi_device *, struct comedi_subdevice *); 305static int pcmmio_cancel(struct comedi_device * dev, struct comedi_subdevice * s); 306static int pcmmio_cmd(struct comedi_device * dev, struct comedi_subdevice * s); 307static int pcmmio_cmdtest(struct comedi_device * dev, struct comedi_subdevice * s, 308 struct comedi_cmd * cmd); 309 310/* some helper functions to deal with specifics of this device's registers */ 311static void init_asics(struct comedi_device * dev); /* sets up/clears ASIC chips to defaults */ 312static void switch_page(struct comedi_device * dev, int asic, int page); 313#ifdef notused 314static void lock_port(struct comedi_device * dev, int asic, int port); 315static void unlock_port(struct comedi_device * dev, int asic, int port); 316#endif 317 318/* 319 * Attach is called by the Comedi core to configure the driver 320 * for a particular board. If you specified a board_name array 321 * in the driver structure, dev->board_ptr contains that 322 * address. 323 */ 324static int pcmmio_attach(struct comedi_device *dev, struct comedi_devconfig *it) 325{ 326 struct comedi_subdevice *s; 327 int sdev_no, chans_left, n_dio_subdevs, n_subdevs, port, asic, 328 thisasic_chanct = 0; 329 unsigned long iobase; 330 unsigned int irq[MAX_ASICS]; 331 332 iobase = it->options[0]; 333 irq[0] = it->options[1]; 334 335 printk("comedi%d: %s: io: %lx ", dev->minor, driver.driver_name, 336 iobase); 337 338 dev->iobase = iobase; 339 340 if (!iobase || !request_region(iobase, 341 thisboard->total_iosize, driver.driver_name)) { 342 printk("I/O port conflict\n"); 343 return -EIO; 344 } 345 346/* 347 * Initialize dev->board_name. Note that we can use the "thisboard" 348 * macro now, since we just initialized it in the last line. 349 */ 350 dev->board_name = thisboard->name; 351 352/* 353 * Allocate the private structure area. alloc_private() is a 354 * convenient macro defined in comedidev.h. 355 */ 356 if (alloc_private(dev, sizeof(struct pcmmio_private)) < 0) { 357 printk("cannot allocate private data structure\n"); 358 return -ENOMEM; 359 } 360 361 for (asic = 0; asic < MAX_ASICS; ++asic) { 362 devpriv->asics[asic].num = asic; 363 devpriv->asics[asic].iobase = 364 dev->iobase + 16 + asic * ASIC_IOSIZE; 365 devpriv->asics[asic].irq = 0; /* this gets actually set at the end of 366 this function when we 367 comedi_request_irqs */ 368 spin_lock_init(&devpriv->asics[asic].spinlock); 369 } 370 371 chans_left = CHANS_PER_ASIC * thisboard->dio_num_asics; 372 n_dio_subdevs = CALC_N_DIO_SUBDEVS(chans_left); 373 n_subdevs = n_dio_subdevs + 2; 374 devpriv->sprivs = 375 kcalloc(n_subdevs, sizeof(struct pcmmio_subdev_private), GFP_KERNEL); 376 if (!devpriv->sprivs) { 377 printk("cannot allocate subdevice private data structures\n"); 378 return -ENOMEM; 379 } 380 /* 381 * Allocate the subdevice structures. alloc_subdevice() is a 382 * convenient macro defined in comedidev.h. 383 * 384 * Allocate 1 AI + 1 AO + 2 DIO subdevs (24 lines per DIO) 385 */ 386 if (alloc_subdevices(dev, n_subdevs) < 0) { 387 printk("cannot allocate subdevice data structures\n"); 388 return -ENOMEM; 389 } 390 391 /* First, AI */ 392 sdev_no = 0; 393 s = dev->subdevices + sdev_no; 394 s->private = devpriv->sprivs + sdev_no; 395 s->maxdata = (1 << thisboard->ai_bits) - 1; 396 s->range_table = thisboard->ai_range_table; 397 s->subdev_flags = SDF_READABLE | SDF_GROUND | SDF_DIFF; 398 s->type = COMEDI_SUBD_AI; 399 s->n_chan = thisboard->n_ai_chans; 400 s->len_chanlist = s->n_chan; 401 s->insn_read = thisboard->ai_rinsn; 402 subpriv->iobase = dev->iobase + 0; 403 /* initialize the resource enable register by clearing it */ 404 outb(0, subpriv->iobase + 3); 405 outb(0, subpriv->iobase + 4 + 3); 406 407 /* Next, AO */ 408 ++sdev_no; 409 s = dev->subdevices + sdev_no; 410 s->private = devpriv->sprivs + sdev_no; 411 s->maxdata = (1 << thisboard->ao_bits) - 1; 412 s->range_table = thisboard->ao_range_table; 413 s->subdev_flags = SDF_READABLE; 414 s->type = COMEDI_SUBD_AO; 415 s->n_chan = thisboard->n_ao_chans; 416 s->len_chanlist = s->n_chan; 417 s->insn_read = thisboard->ao_rinsn; 418 s->insn_write = thisboard->ao_winsn; 419 subpriv->iobase = dev->iobase + 8; 420 /* initialize the resource enable register by clearing it */ 421 outb(0, subpriv->iobase + 3); 422 outb(0, subpriv->iobase + 4 + 3); 423 424 ++sdev_no; 425 port = 0; 426 asic = 0; 427 for (; sdev_no < (int)dev->n_subdevices; ++sdev_no) { 428 int byte_no; 429 430 s = dev->subdevices + sdev_no; 431 s->private = devpriv->sprivs + sdev_no; 432 s->maxdata = 1; 433 s->range_table = &range_digital; 434 s->subdev_flags = SDF_READABLE | SDF_WRITABLE; 435 s->type = COMEDI_SUBD_DIO; 436 s->insn_bits = pcmmio_dio_insn_bits; 437 s->insn_config = pcmmio_dio_insn_config; 438 s->n_chan = MIN(chans_left, MAX_CHANS_PER_SUBDEV); 439 subpriv->dio.intr.asic = -1; 440 subpriv->dio.intr.first_chan = -1; 441 subpriv->dio.intr.asic_chan = -1; 442 subpriv->dio.intr.num_asic_chans = -1; 443 subpriv->dio.intr.active = 0; 444 s->len_chanlist = 1; 445 446 /* save the ioport address for each 'port' of 8 channels in the 447 subdevice */ 448 for (byte_no = 0; byte_no < PORTS_PER_SUBDEV; ++byte_no, ++port) { 449 if (port >= PORTS_PER_ASIC) { 450 port = 0; 451 ++asic; 452 thisasic_chanct = 0; 453 } 454 subpriv->iobases[byte_no] = 455 devpriv->asics[asic].iobase + port; 456 457 if (thisasic_chanct < 458 CHANS_PER_PORT * INTR_PORTS_PER_ASIC 459 && subpriv->dio.intr.asic < 0) { 460 /* this is an interrupt subdevice, so setup the struct */ 461 subpriv->dio.intr.asic = asic; 462 subpriv->dio.intr.active = 0; 463 subpriv->dio.intr.stop_count = 0; 464 subpriv->dio.intr.first_chan = byte_no * 8; 465 subpriv->dio.intr.asic_chan = thisasic_chanct; 466 subpriv->dio.intr.num_asic_chans = 467 s->n_chan - 468 subpriv->dio.intr.first_chan; 469 s->cancel = pcmmio_cancel; 470 s->do_cmd = pcmmio_cmd; 471 s->do_cmdtest = pcmmio_cmdtest; 472 s->len_chanlist = 473 subpriv->dio.intr.num_asic_chans; 474 } 475 thisasic_chanct += CHANS_PER_PORT; 476 } 477 spin_lock_init(&subpriv->dio.intr.spinlock); 478 479 chans_left -= s->n_chan; 480 481 if (!chans_left) { 482 asic = 0; /* reset the asic to our first asic, to do intr subdevs */ 483 port = 0; 484 } 485 486 } 487 488 init_asics(dev); /* clear out all the registers, basically */ 489 490 for (asic = 0; irq[0] && asic < MAX_ASICS; ++asic) { 491 if (irq[asic] 492 && comedi_request_irq(irq[asic], interrupt_pcmmio, 493 IRQF_SHARED, thisboard->name, dev)) { 494 int i; 495 /* unroll the allocated irqs.. */ 496 for (i = asic - 1; i >= 0; --i) { 497 comedi_free_irq(irq[i], dev); 498 devpriv->asics[i].irq = irq[i] = 0; 499 } 500 irq[asic] = 0; 501 } 502 devpriv->asics[asic].irq = irq[asic]; 503 } 504 505 dev->irq = irq[0]; /* grr.. wish comedi dev struct supported multiple 506 irqs.. */ 507 508 if (irq[0]) { 509 printk("irq: %u ", irq[0]); 510 if (irq[1] && thisboard->dio_num_asics == 2) 511 printk("second ASIC irq: %u ", irq[1]); 512 } else { 513 printk("(IRQ mode disabled) "); 514 } 515 516 printk("attached\n"); 517 518 return 1; 519} 520 521/* 522 * _detach is called to deconfigure a device. It should deallocate 523 * resources. 524 * This function is also called when _attach() fails, so it should be 525 * careful not to release resources that were not necessarily 526 * allocated by _attach(). dev->private and dev->subdevices are 527 * deallocated automatically by the core. 528 */ 529static int pcmmio_detach(struct comedi_device *dev) 530{ 531 int i; 532 533 printk("comedi%d: %s: remove\n", dev->minor, driver.driver_name); 534 if (dev->iobase) 535 release_region(dev->iobase, thisboard->total_iosize); 536 537 for (i = 0; i < MAX_ASICS; ++i) { 538 if (devpriv && devpriv->asics[i].irq) 539 comedi_free_irq(devpriv->asics[i].irq, dev); 540 } 541 542 if (devpriv && devpriv->sprivs) 543 kfree(devpriv->sprivs); 544 545 return 0; 546} 547 548/* DIO devices are slightly special. Although it is possible to 549 * implement the insn_read/insn_write interface, it is much more 550 * useful to applications if you implement the insn_bits interface. 551 * This allows packed reading/writing of the DIO channels. The 552 * comedi core can convert between insn_bits and insn_read/write */ 553static int pcmmio_dio_insn_bits(struct comedi_device *dev, struct comedi_subdevice *s, 554 struct comedi_insn *insn, unsigned int *data) 555{ 556 int byte_no; 557 if (insn->n != 2) 558 return -EINVAL; 559 560 /* NOTE: 561 reading a 0 means this channel was high 562 writine a 0 sets the channel high 563 reading a 1 means this channel was low 564 writing a 1 means set this channel low 565 566 Therefore everything is always inverted. */ 567 568 /* The insn data is a mask in data[0] and the new data 569 * in data[1], each channel cooresponding to a bit. */ 570 571#ifdef DAMMIT_ITS_BROKEN 572 /* DEBUG */ 573 printk("write mask: %08x data: %08x\n", data[0], data[1]); 574#endif 575 576 s->state = 0; 577 578 for (byte_no = 0; byte_no < s->n_chan / CHANS_PER_PORT; ++byte_no) { 579 /* address of 8-bit port */ 580 unsigned long ioaddr = subpriv->iobases[byte_no], 581 /* bit offset of port in 32-bit doubleword */ 582 offset = byte_no * 8; 583 /* this 8-bit port's data */ 584 unsigned char byte = 0, 585 /* The write mask for this port (if any) */ 586 write_mask_byte = (data[0] >> offset) & 0xff, 587 /* The data byte for this port */ 588 data_byte = (data[1] >> offset) & 0xff; 589 590 byte = inb(ioaddr); /* read all 8-bits for this port */ 591 592#ifdef DAMMIT_ITS_BROKEN 593 /* DEBUG */ 594 printk("byte %d wmb %02x db %02x offset %02d io %04x, data_in %02x ", byte_no, (unsigned)write_mask_byte, (unsigned)data_byte, offset, ioaddr, (unsigned)byte); 595#endif 596 597 if (write_mask_byte) { 598 /* this byte has some write_bits -- so set the output lines */ 599 byte &= ~write_mask_byte; /* clear bits for write mask */ 600 byte |= ~data_byte & write_mask_byte; /* set to inverted data_byte */ 601 /* Write out the new digital output state */ 602 outb(byte, ioaddr); 603 } 604#ifdef DAMMIT_ITS_BROKEN 605 /* DEBUG */ 606 printk("data_out_byte %02x\n", (unsigned)byte); 607#endif 608 /* save the digital input lines for this byte.. */ 609 s->state |= ((unsigned int)byte) << offset; 610 } 611 612 /* now return the DIO lines to data[1] - note they came inverted! */ 613 data[1] = ~s->state; 614 615#ifdef DAMMIT_ITS_BROKEN 616 /* DEBUG */ 617 printk("s->state %08x data_out %08x\n", s->state, data[1]); 618#endif 619 620 return 2; 621} 622 623/* The input or output configuration of each digital line is 624 * configured by a special insn_config instruction. chanspec 625 * contains the channel to be changed, and data[0] contains the 626 * value COMEDI_INPUT or COMEDI_OUTPUT. */ 627static int pcmmio_dio_insn_config(struct comedi_device *dev, struct comedi_subdevice *s, 628 struct comedi_insn *insn, unsigned int *data) 629{ 630 int chan = CR_CHAN(insn->chanspec), byte_no = chan / 8, bit_no = 631 chan % 8; 632 unsigned long ioaddr; 633 unsigned char byte; 634 635 /* Compute ioaddr for this channel */ 636 ioaddr = subpriv->iobases[byte_no]; 637 638 /* NOTE: 639 writing a 0 an IO channel's bit sets the channel to INPUT 640 and pulls the line high as well 641 642 writing a 1 to an IO channel's bit pulls the line low 643 644 All channels are implicitly always in OUTPUT mode -- but when 645 they are high they can be considered to be in INPUT mode.. 646 647 Thus, we only force channels low if the config request was INPUT, 648 otherwise we do nothing to the hardware. */ 649 650 switch (data[0]) { 651 case INSN_CONFIG_DIO_OUTPUT: 652 /* save to io_bits -- don't actually do anything since 653 all input channels are also output channels... */ 654 s->io_bits |= 1 << chan; 655 break; 656 case INSN_CONFIG_DIO_INPUT: 657 /* write a 0 to the actual register representing the channel 658 to set it to 'input'. 0 means "float high". */ 659 byte = inb(ioaddr); 660 byte &= ~(1 << bit_no); 661 /**< set input channel to '0' */ 662 663 /* write out byte -- this is the only time we actually affect the 664 hardware as all channels are implicitly output -- but input 665 channels are set to float-high */ 666 outb(byte, ioaddr); 667 668 /* save to io_bits */ 669 s->io_bits &= ~(1 << chan); 670 break; 671 672 case INSN_CONFIG_DIO_QUERY: 673 /* retreive from shadow register */ 674 data[1] = 675 (s-> 676 io_bits & (1 << chan)) ? COMEDI_OUTPUT : COMEDI_INPUT; 677 return insn->n; 678 break; 679 680 default: 681 return -EINVAL; 682 break; 683 } 684 685 return insn->n; 686} 687 688static void init_asics(struct comedi_device *dev) 689{ /* sets up an 690 ASIC chip to defaults */ 691 int asic; 692 693 for (asic = 0; asic < thisboard->dio_num_asics; ++asic) { 694 int port, page; 695 unsigned long baseaddr = devpriv->asics[asic].iobase; 696 697 switch_page(dev, asic, 0); /* switch back to page 0 */ 698 699 /* first, clear all the DIO port bits */ 700 for (port = 0; port < PORTS_PER_ASIC; ++port) 701 outb(0, baseaddr + REG_PORT0 + port); 702 703 /* Next, clear all the paged registers for each page */ 704 for (page = 1; page < NUM_PAGES; ++page) { 705 int reg; 706 /* now clear all the paged registers */ 707 switch_page(dev, asic, page); 708 for (reg = FIRST_PAGED_REG; 709 reg < FIRST_PAGED_REG + NUM_PAGED_REGS; ++reg) 710 outb(0, baseaddr + reg); 711 } 712 713 /* DEBUG set rising edge interrupts on port0 of both asics */ 714 /*switch_page(dev, asic, PAGE_POL); 715 outb(0xff, baseaddr + REG_POL0); 716 switch_page(dev, asic, PAGE_ENAB); 717 outb(0xff, baseaddr + REG_ENAB0); */ 718 /* END DEBUG */ 719 720 switch_page(dev, asic, 0); /* switch back to default page 0 */ 721 722 } 723} 724 725static void switch_page(struct comedi_device *dev, int asic, int page) 726{ 727 if (asic < 0 || asic >= thisboard->dio_num_asics) 728 return; /* paranoia */ 729 if (page < 0 || page >= NUM_PAGES) 730 return; /* more paranoia */ 731 732 devpriv->asics[asic].pagelock &= ~REG_PAGE_MASK; 733 devpriv->asics[asic].pagelock |= page << REG_PAGE_BITOFFSET; 734 735 /* now write out the shadow register */ 736 outb(devpriv->asics[asic].pagelock, 737 devpriv->asics[asic].iobase + REG_PAGELOCK); 738} 739 740#ifdef notused 741static void lock_port(struct comedi_device *dev, int asic, int port) 742{ 743 if (asic < 0 || asic >= thisboard->dio_num_asics) 744 return; /* paranoia */ 745 if (port < 0 || port >= PORTS_PER_ASIC) 746 return; /* more paranoia */ 747 748 devpriv->asics[asic].pagelock |= 0x1 << port; 749 /* now write out the shadow register */ 750 outb(devpriv->asics[asic].pagelock, 751 devpriv->asics[asic].iobase + REG_PAGELOCK); 752 return; 753} 754 755static void unlock_port(struct comedi_device *dev, int asic, int port) 756{ 757 if (asic < 0 || asic >= thisboard->dio_num_asics) 758 return; /* paranoia */ 759 if (port < 0 || port >= PORTS_PER_ASIC) 760 return; /* more paranoia */ 761 devpriv->asics[asic].pagelock &= ~(0x1 << port) | REG_LOCK_MASK; 762 /* now write out the shadow register */ 763 outb(devpriv->asics[asic].pagelock, 764 devpriv->asics[asic].iobase + REG_PAGELOCK); 765} 766#endif /* notused */ 767 768static irqreturn_t interrupt_pcmmio(int irq, void *d) 769{ 770 int asic, got1 = 0; 771 struct comedi_device *dev = (struct comedi_device *) d; 772 773 for (asic = 0; asic < MAX_ASICS; ++asic) { 774 if (irq == devpriv->asics[asic].irq) { 775 unsigned long flags; 776 unsigned triggered = 0; 777 unsigned long iobase = devpriv->asics[asic].iobase; 778 /* it is an interrupt for ASIC #asic */ 779 unsigned char int_pend; 780 781 comedi_spin_lock_irqsave(&devpriv->asics[asic].spinlock, 782 flags); 783 784 int_pend = inb(iobase + REG_INT_PENDING) & 0x07; 785 786 if (int_pend) { 787 int port; 788 for (port = 0; port < INTR_PORTS_PER_ASIC; 789 ++port) { 790 if (int_pend & (0x1 << port)) { 791 unsigned char 792 io_lines_with_edges = 0; 793 switch_page(dev, asic, 794 PAGE_INT_ID); 795 io_lines_with_edges = 796 inb(iobase + 797 REG_INT_ID0 + port); 798 799 if (io_lines_with_edges) 800 /* clear pending interrupt */ 801 outb(0, iobase + 802 REG_INT_ID0 + 803 port); 804 805 triggered |= 806 io_lines_with_edges << 807 port * 8; 808 } 809 } 810 811 ++got1; 812 } 813 814 comedi_spin_unlock_irqrestore(&devpriv->asics[asic]. 815 spinlock, flags); 816 817 if (triggered) { 818 struct comedi_subdevice *s; 819 /* TODO here: dispatch io lines to subdevs with commands.. */ 820 printk("PCMMIO DEBUG: got edge detect interrupt %d asic %d which_chans: %06x\n", irq, asic, triggered); 821 for (s = dev->subdevices + 2; 822 s < dev->subdevices + dev->n_subdevices; 823 ++s) { 824 if (subpriv->dio.intr.asic == asic) { /* this is an interrupt subdev, and it matches this asic! */ 825 unsigned long flags; 826 unsigned oldevents; 827 828 comedi_spin_lock_irqsave 829 (&subpriv->dio.intr. 830 spinlock, flags); 831 832 oldevents = s->async->events; 833 834 if (subpriv->dio.intr.active) { 835 unsigned mytrig = 836 ((triggered >> 837 subpriv-> 838 dio. 839 intr. 840 asic_chan) 841 & ((0x1 << subpriv->dio.intr.num_asic_chans) - 1)) << subpriv->dio.intr.first_chan; 842 if (mytrig & subpriv-> 843 dio.intr. 844 enabled_mask) { 845 unsigned int val = 846 0; 847 unsigned int n, 848 ch, len; 849 850 len = s->async-> 851 cmd. 852 chanlist_len; 853 for (n = 0; 854 n < len; 855 n++) { 856 ch = CR_CHAN(s->async->cmd.chanlist[n]); 857 if (mytrig & (1U << ch)) { 858 val |= (1U << n); 859 } 860 } 861 /* Write the scan to the buffer. */ 862 if (comedi_buf_put(s->async, ((short *) & val)[0]) 863 && 864 comedi_buf_put 865 (s->async, ((short *) & val)[1])) { 866 s->async->events |= (COMEDI_CB_BLOCK | COMEDI_CB_EOS); 867 } else { 868 /* Overflow! Stop acquisition!! */ 869 /* TODO: STOP_ACQUISITION_CALL_HERE!! */ 870 pcmmio_stop_intr 871 (dev, 872 s); 873 } 874 875 /* Check for end of acquisition. */ 876 if (!subpriv-> 877 dio. 878 intr. 879 continuous) 880 { 881 /* stop_src == TRIG_COUNT */ 882 if (subpriv->dio.intr.stop_count > 0) { 883 subpriv-> 884 dio. 885 intr. 886 stop_count--; 887 if (subpriv->dio.intr.stop_count == 0) { 888 s->async->events |= COMEDI_CB_EOA; 889 /* TODO: STOP_ACQUISITION_CALL_HERE!! */ 890 pcmmio_stop_intr 891 (dev, 892 s); 893 } 894 } 895 } 896 } 897 } 898 899 comedi_spin_unlock_irqrestore 900 (&subpriv->dio.intr. 901 spinlock, flags); 902 903 if (oldevents != 904 s->async->events) { 905 comedi_event(dev, s); 906 } 907 908 } 909 910 } 911 } 912 913 } 914 } 915 if (!got1) 916 return IRQ_NONE; /* interrupt from other source */ 917 return IRQ_HANDLED; 918} 919 920static void pcmmio_stop_intr(struct comedi_device *dev, struct comedi_subdevice *s) 921{ 922 int nports, firstport, asic, port; 923 924 if ((asic = subpriv->dio.intr.asic) < 0) 925 return; /* not an interrupt subdev */ 926 927 subpriv->dio.intr.enabled_mask = 0; 928 subpriv->dio.intr.active = 0; 929 s->async->inttrig = 0; 930 nports = subpriv->dio.intr.num_asic_chans / CHANS_PER_PORT; 931 firstport = subpriv->dio.intr.asic_chan / CHANS_PER_PORT; 932 switch_page(dev, asic, PAGE_ENAB); 933 for (port = firstport; port < firstport + nports; ++port) { 934 /* disable all intrs for this subdev.. */ 935 outb(0, devpriv->asics[asic].iobase + REG_ENAB0 + port); 936 } 937} 938 939static int pcmmio_start_intr(struct comedi_device *dev, struct comedi_subdevice *s) 940{ 941 if (!subpriv->dio.intr.continuous && subpriv->dio.intr.stop_count == 0) { 942 /* An empty acquisition! */ 943 s->async->events |= COMEDI_CB_EOA; 944 subpriv->dio.intr.active = 0; 945 return 1; 946 } else { 947 unsigned bits = 0, pol_bits = 0, n; 948 int nports, firstport, asic, port; 949 struct comedi_cmd *cmd = &s->async->cmd; 950 951 if ((asic = subpriv->dio.intr.asic) < 0) 952 return 1; /* not an interrupt 953 subdev */ 954 subpriv->dio.intr.enabled_mask = 0; 955 subpriv->dio.intr.active = 1; 956 nports = subpriv->dio.intr.num_asic_chans / CHANS_PER_PORT; 957 firstport = subpriv->dio.intr.asic_chan / CHANS_PER_PORT; 958 if (cmd->chanlist) { 959 for (n = 0; n < cmd->chanlist_len; n++) { 960 bits |= (1U << CR_CHAN(cmd->chanlist[n])); 961 pol_bits |= (CR_AREF(cmd->chanlist[n]) 962 || CR_RANGE(cmd->chanlist[n]) ? 1U : 0U) 963 << CR_CHAN(cmd->chanlist[n]); 964 } 965 } 966 bits &= ((0x1 << subpriv->dio.intr.num_asic_chans) - 967 1) << subpriv->dio.intr.first_chan; 968 subpriv->dio.intr.enabled_mask = bits; 969 970 { /* the below code configures the board to use a specific IRQ from 0-15. */ 971 unsigned char b; 972 /* set resource enable register to enable IRQ operation */ 973 outb(1 << 4, dev->iobase + 3); 974 /* set bits 0-3 of b to the irq number from 0-15 */ 975 b = dev->irq & ((1 << 4) - 1); 976 outb(b, dev->iobase + 2); 977 /* done, we told the board what irq to use */ 978 } 979 980 switch_page(dev, asic, PAGE_ENAB); 981 for (port = firstport; port < firstport + nports; ++port) { 982 unsigned enab = 983 bits >> (subpriv->dio.intr.first_chan + (port - 984 firstport) * 8) & 0xff, pol = 985 pol_bits >> (subpriv->dio.intr.first_chan + 986 (port - firstport) * 8) & 0xff; 987 /* set enab intrs for this subdev.. */ 988 outb(enab, 989 devpriv->asics[asic].iobase + REG_ENAB0 + port); 990 switch_page(dev, asic, PAGE_POL); 991 outb(pol, 992 devpriv->asics[asic].iobase + REG_ENAB0 + port); 993 } 994 } 995 return 0; 996} 997 998static int pcmmio_cancel(struct comedi_device *dev, struct comedi_subdevice *s) 999{ 1000 unsigned long flags; 1001 1002 comedi_spin_lock_irqsave(&subpriv->dio.intr.spinlock, flags); 1003 if (subpriv->dio.intr.active) 1004 pcmmio_stop_intr(dev, s); 1005 comedi_spin_unlock_irqrestore(&subpriv->dio.intr.spinlock, flags); 1006 1007 return 0; 1008} 1009 1010/* 1011 * Internal trigger function to start acquisition for an 'INTERRUPT' subdevice. 1012 */ 1013static int 1014pcmmio_inttrig_start_intr(struct comedi_device *dev, struct comedi_subdevice *s, 1015 unsigned int trignum) 1016{ 1017 unsigned long flags; 1018 int event = 0; 1019 1020 if (trignum != 0) 1021 return -EINVAL; 1022 1023 comedi_spin_lock_irqsave(&subpriv->dio.intr.spinlock, flags); 1024 s->async->inttrig = 0; 1025 if (subpriv->dio.intr.active) { 1026 event = pcmmio_start_intr(dev, s); 1027 } 1028 comedi_spin_unlock_irqrestore(&subpriv->dio.intr.spinlock, flags); 1029 1030 if (event) { 1031 comedi_event(dev, s); 1032 } 1033 1034 return 1; 1035} 1036 1037/* 1038 * 'do_cmd' function for an 'INTERRUPT' subdevice. 1039 */ 1040static int pcmmio_cmd(struct comedi_device *dev, struct comedi_subdevice *s) 1041{ 1042 struct comedi_cmd *cmd = &s->async->cmd; 1043 unsigned long flags; 1044 int event = 0; 1045 1046 comedi_spin_lock_irqsave(&subpriv->dio.intr.spinlock, flags); 1047 subpriv->dio.intr.active = 1; 1048 1049 /* Set up end of acquisition. */ 1050 switch (cmd->stop_src) { 1051 case TRIG_COUNT: 1052 subpriv->dio.intr.continuous = 0; 1053 subpriv->dio.intr.stop_count = cmd->stop_arg; 1054 break; 1055 default: 1056 /* TRIG_NONE */ 1057 subpriv->dio.intr.continuous = 1; 1058 subpriv->dio.intr.stop_count = 0; 1059 break; 1060 } 1061 1062 /* Set up start of acquisition. */ 1063 switch (cmd->start_src) { 1064 case TRIG_INT: 1065 s->async->inttrig = pcmmio_inttrig_start_intr; 1066 break; 1067 default: 1068 /* TRIG_NOW */ 1069 event = pcmmio_start_intr(dev, s); 1070 break; 1071 } 1072 comedi_spin_unlock_irqrestore(&subpriv->dio.intr.spinlock, flags); 1073 1074 if (event) { 1075 comedi_event(dev, s); 1076 } 1077 1078 return 0; 1079} 1080 1081/* 1082 * 'do_cmdtest' function for an 'INTERRUPT' subdevice. 1083 */ 1084static int 1085pcmmio_cmdtest(struct comedi_device *dev, struct comedi_subdevice *s, struct comedi_cmd *cmd) 1086{ 1087 int err = 0; 1088 unsigned int tmp; 1089 1090 /* step 1: make sure trigger sources are trivially valid */ 1091 1092 tmp = cmd->start_src; 1093 cmd->start_src &= (TRIG_NOW | TRIG_INT); 1094 if (!cmd->start_src || tmp != cmd->start_src) 1095 err++; 1096 1097 tmp = cmd->scan_begin_src; 1098 cmd->scan_begin_src &= TRIG_EXT; 1099 if (!cmd->scan_begin_src || tmp != cmd->scan_begin_src) 1100 err++; 1101 1102 tmp = cmd->convert_src; 1103 cmd->convert_src &= TRIG_NOW; 1104 if (!cmd->convert_src || tmp != cmd->convert_src) 1105 err++; 1106 1107 tmp = cmd->scan_end_src; 1108 cmd->scan_end_src &= TRIG_COUNT; 1109 if (!cmd->scan_end_src || tmp != cmd->scan_end_src) 1110 err++; 1111 1112 tmp = cmd->stop_src; 1113 cmd->stop_src &= (TRIG_COUNT | TRIG_NONE); 1114 if (!cmd->stop_src || tmp != cmd->stop_src) 1115 err++; 1116 1117 if (err) 1118 return 1; 1119 1120 /* step 2: make sure trigger sources are unique and mutually compatible */ 1121 1122 /* these tests are true if more than one _src bit is set */ 1123 if ((cmd->start_src & (cmd->start_src - 1)) != 0) 1124 err++; 1125 if ((cmd->scan_begin_src & (cmd->scan_begin_src - 1)) != 0) 1126 err++; 1127 if ((cmd->convert_src & (cmd->convert_src - 1)) != 0) 1128 err++; 1129 if ((cmd->scan_end_src & (cmd->scan_end_src - 1)) != 0) 1130 err++; 1131 if ((cmd->stop_src & (cmd->stop_src - 1)) != 0) 1132 err++; 1133 1134 if (err) 1135 return 2; 1136 1137 /* step 3: make sure arguments are trivially compatible */ 1138 1139 /* cmd->start_src == TRIG_NOW || cmd->start_src == TRIG_INT */ 1140 if (cmd->start_arg != 0) { 1141 cmd->start_arg = 0; 1142 err++; 1143 } 1144 1145 /* cmd->scan_begin_src == TRIG_EXT */ 1146 if (cmd->scan_begin_arg != 0) { 1147 cmd->scan_begin_arg = 0; 1148 err++; 1149 } 1150 1151 /* cmd->convert_src == TRIG_NOW */ 1152 if (cmd->convert_arg != 0) { 1153 cmd->convert_arg = 0; 1154 err++; 1155 } 1156 1157 /* cmd->scan_end_src == TRIG_COUNT */ 1158 if (cmd->scan_end_arg != cmd->chanlist_len) { 1159 cmd->scan_end_arg = cmd->chanlist_len; 1160 err++; 1161 } 1162 1163 switch (cmd->stop_src) { 1164 case TRIG_COUNT: 1165 /* any count allowed */ 1166 break; 1167 case TRIG_NONE: 1168 if (cmd->stop_arg != 0) { 1169 cmd->stop_arg = 0; 1170 err++; 1171 } 1172 break; 1173 default: 1174 break; 1175 } 1176 1177 if (err) 1178 return 3; 1179 1180 /* step 4: fix up any arguments */ 1181 1182 /* if (err) return 4; */ 1183 1184 return 0; 1185} 1186 1187static int adc_wait_ready(unsigned long iobase) 1188{ 1189 unsigned long retry = 100000; 1190 while (retry--) 1191 if (inb(iobase + 3) & 0x80) 1192 return 0; 1193 return 1; 1194} 1195 1196/* All this is for AI and AO */ 1197static int ai_rinsn(struct comedi_device *dev, struct comedi_subdevice *s, 1198 struct comedi_insn *insn, unsigned int *data) 1199{ 1200 int n; 1201 unsigned long iobase = subpriv->iobase; 1202 1203 /* 1204 1. write the CMD byte (to BASE+2) 1205 2. read junk lo byte (BASE+0) 1206 3. read junk hi byte (BASE+1) 1207 4. (mux settled so) write CMD byte again (BASE+2) 1208 5. read valid lo byte(BASE+0) 1209 6. read valid hi byte(BASE+1) 1210 1211 Additionally note that the BASE += 4 if the channel >= 8 1212 */ 1213 1214 /* convert n samples */ 1215 for (n = 0; n < insn->n; n++) { 1216 unsigned chan = CR_CHAN(insn->chanspec), range = 1217 CR_RANGE(insn->chanspec), aref = 1218 CR_AREF(insn->chanspec); 1219 unsigned char command_byte = 0; 1220 unsigned iooffset = 0; 1221 short sample, adc_adjust = 0; 1222 1223 if (chan > 7) 1224 chan -= 8, iooffset = 4; /* use the second dword for channels > 7 */ 1225 1226 if (aref != AREF_DIFF) { 1227 aref = AREF_GROUND; 1228 command_byte |= 1 << 7; /* set bit 7 to indicate single-ended */ 1229 } 1230 if (range < 2) 1231 adc_adjust = 0x8000; /* bipolar ranges (-5,5 .. -10,10 need to be adjusted -- that is.. they need to wrap around by adding 0x8000 */ 1232 1233 if (chan % 2) { 1234 command_byte |= 1 << 6; /* odd-numbered channels have bit 6 set */ 1235 } 1236 1237 /* select the channel, bits 4-5 == chan/2 */ 1238 command_byte |= ((chan / 2) & 0x3) << 4; 1239 1240 /* set the range, bits 2-3 */ 1241 command_byte |= (range & 0x3) << 2; 1242 1243 /* need to do this twice to make sure mux settled */ 1244 outb(command_byte, iobase + iooffset + 2); /* chan/range/aref select */ 1245 1246 adc_wait_ready(iobase + iooffset); /* wait for the adc to say it finised the conversion */ 1247 1248 outb(command_byte, iobase + iooffset + 2); /* select the chan/range/aref AGAIN */ 1249 1250 adc_wait_ready(iobase + iooffset); 1251 1252 sample = inb(iobase + iooffset + 0); /* read data lo byte */ 1253 sample |= inb(iobase + iooffset + 1) << 8; /* read data hi byte */ 1254 sample += adc_adjust; /* adjustment .. munge data */ 1255 data[n] = sample; 1256 } 1257 /* return the number of samples read/written */ 1258 return n; 1259} 1260 1261static int ao_rinsn(struct comedi_device *dev, struct comedi_subdevice *s, 1262 struct comedi_insn *insn, unsigned int *data) 1263{ 1264 int n; 1265 for (n = 0; n < insn->n; n++) { 1266 unsigned chan = CR_CHAN(insn->chanspec); 1267 if (chan < s->n_chan) 1268 data[n] = subpriv->ao.shadow_samples[chan]; 1269 } 1270 return n; 1271} 1272 1273static int wait_dac_ready(unsigned long iobase) 1274{ 1275 unsigned long retry = 100000L; 1276 1277 /* This may seem like an absurd way to handle waiting and violates the 1278 "no busy waiting" policy. The fact is that the hardware is 1279 normally so fast that we usually only need one time through the loop 1280 anyway. The longer timeout is for rare occasions and for detecting 1281 non-existant hardware. */ 1282 1283 while (retry--) { 1284 if (inb(iobase + 3) & 0x80) 1285 return 0; 1286 1287 } 1288 return 1; 1289} 1290 1291static int ao_winsn(struct comedi_device *dev, struct comedi_subdevice *s, 1292 struct comedi_insn *insn, unsigned int *data) 1293{ 1294 int n; 1295 unsigned iobase = subpriv->iobase, iooffset = 0; 1296 1297 for (n = 0; n < insn->n; n++) { 1298 unsigned chan = CR_CHAN(insn->chanspec), range = 1299 CR_RANGE(insn->chanspec); 1300 if (chan < s->n_chan) { 1301 unsigned char command_byte = 0, range_byte = 1302 range & ((1 << 4) - 1); 1303 if (chan >= 4) 1304 chan -= 4, iooffset += 4; 1305 /* set the range.. */ 1306 outb(range_byte, iobase + iooffset + 0); 1307 outb(0, iobase + iooffset + 1); 1308 1309 /* tell it to begin */ 1310 command_byte = (chan << 1) | 0x60; 1311 outb(command_byte, iobase + iooffset + 2); 1312 1313 wait_dac_ready(iobase + iooffset); 1314 1315 outb(data[n] & 0xff, iobase + iooffset + 0); /* low order byte */ 1316 outb((data[n] >> 8) & 0xff, iobase + iooffset + 1); /* high order byte */ 1317 command_byte = 0x70 | (chan << 1); /* set bit 4 of command byte to indicate data is loaded and trigger conversion */ 1318 /* trigger converion */ 1319 outb(command_byte, iobase + iooffset + 2); 1320 1321 wait_dac_ready(iobase + iooffset); 1322 1323 subpriv->ao.shadow_samples[chan] = data[n]; /* save to shadow register for ao_rinsn */ 1324 } 1325 } 1326 return n; 1327} 1328 1329/* 1330 * A convenient macro that defines init_module() and cleanup_module(), 1331 * as necessary. 1332 */ 1333COMEDI_INITCLEANUP(driver); 1334