s626.c revision b6c777571b8d387d3add91170826f32a379e4313
1/* 2 comedi/drivers/s626.c 3 Sensoray s626 Comedi driver 4 5 COMEDI - Linux Control and Measurement Device Interface 6 Copyright (C) 2000 David A. Schleef <ds@schleef.org> 7 8 Based on Sensoray Model 626 Linux driver Version 0.2 9 Copyright (C) 2002-2004 Sensoray Co., Inc. 10 11 This program is free software; you can redistribute it and/or modify 12 it under the terms of the GNU General Public License as published by 13 the Free Software Foundation; either version 2 of the License, or 14 (at your option) any later version. 15 16 This program is distributed in the hope that it will be useful, 17 but WITHOUT ANY WARRANTY; without even the implied warranty of 18 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 19 GNU General Public License for more details. 20 21 You should have received a copy of the GNU General Public License 22 along with this program; if not, write to the Free Software 23 Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. 24 25*/ 26 27/* 28Driver: s626 29Description: Sensoray 626 driver 30Devices: [Sensoray] 626 (s626) 31Authors: Gianluca Palli <gpalli@deis.unibo.it>, 32Updated: Fri, 15 Feb 2008 10:28:42 +0000 33Status: experimental 34 35Configuration options: 36 [0] - PCI bus of device (optional) 37 [1] - PCI slot of device (optional) 38 If bus/slot is not specified, the first supported 39 PCI device found will be used. 40 41INSN_CONFIG instructions: 42 analog input: 43 none 44 45 analog output: 46 none 47 48 digital channel: 49 s626 has 3 dio subdevices (2,3 and 4) each with 16 i/o channels 50 supported configuration options: 51 INSN_CONFIG_DIO_QUERY 52 COMEDI_INPUT 53 COMEDI_OUTPUT 54 55 encoder: 56 Every channel must be configured before reading. 57 58 Example code 59 60 insn.insn=INSN_CONFIG; //configuration instruction 61 insn.n=1; //number of operation (must be 1) 62 insn.data=&initialvalue; //initial value loaded into encoder 63 //during configuration 64 insn.subdev=5; //encoder subdevice 65 insn.chanspec=CR_PACK(encoder_channel,0,AREF_OTHER); //encoder_channel 66 //to configure 67 68 comedi_do_insn(cf,&insn); //executing configuration 69*/ 70 71#include <linux/kernel.h> 72#include <linux/types.h> 73 74#include "../comedidev.h" 75 76#include "comedi_pci.h" 77 78#include "comedi_fc.h" 79#include "s626.h" 80 81MODULE_AUTHOR("Gianluca Palli <gpalli@deis.unibo.it>"); 82MODULE_DESCRIPTION("Sensoray 626 Comedi driver module"); 83MODULE_LICENSE("GPL"); 84 85typedef struct s626_board_struct { 86 const char *name; 87 int ai_chans; 88 int ai_bits; 89 int ao_chans; 90 int ao_bits; 91 int dio_chans; 92 int dio_banks; 93 int enc_chans; 94} s626_board; 95 96static const s626_board s626_boards[] = { 97 { 98 name: "s626", 99 ai_chans:S626_ADC_CHANNELS, 100 ai_bits: 14, 101 ao_chans:S626_DAC_CHANNELS, 102 ao_bits: 13, 103 dio_chans:S626_DIO_CHANNELS, 104 dio_banks:S626_DIO_BANKS, 105 enc_chans:S626_ENCODER_CHANNELS, 106 } 107}; 108 109#define thisboard ((const s626_board *)dev->board_ptr) 110#define PCI_VENDOR_ID_S626 0x1131 111#define PCI_DEVICE_ID_S626 0x7146 112 113static DEFINE_PCI_DEVICE_TABLE(s626_pci_table) = { 114 {PCI_VENDOR_ID_S626, PCI_DEVICE_ID_S626, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 115 0}, 116 {0} 117}; 118 119MODULE_DEVICE_TABLE(pci, s626_pci_table); 120 121static int s626_attach(comedi_device * dev, comedi_devconfig * it); 122static int s626_detach(comedi_device * dev); 123 124static comedi_driver driver_s626 = { 125 driver_name:"s626", 126 module:THIS_MODULE, 127 attach:s626_attach, 128 detach:s626_detach, 129}; 130 131typedef struct { 132 struct pci_dev *pdev; 133 void *base_addr; 134 int got_regions; 135 short allocatedBuf; 136 uint8_t ai_cmd_running; /* ai_cmd is running */ 137 uint8_t ai_continous; /* continous aquisition */ 138 int ai_sample_count; /* number of samples to aquire */ 139 unsigned int ai_sample_timer; 140 /* time between samples in units of the timer */ 141 int ai_convert_count; /* conversion counter */ 142 unsigned int ai_convert_timer; 143 /* time between conversion in units of the timer */ 144 uint16_t CounterIntEnabs; 145 /* Counter interrupt enable mask for MISC2 register. */ 146 uint8_t AdcItems; /* Number of items in ADC poll list. */ 147 DMABUF RPSBuf; /* DMA buffer used to hold ADC (RPS1) program. */ 148 DMABUF ANABuf; 149 /* DMA buffer used to receive ADC data and hold DAC data. */ 150 uint32_t *pDacWBuf; 151 /* Pointer to logical adrs of DMA buffer used to hold DAC data. */ 152 uint16_t Dacpol; /* Image of DAC polarity register. */ 153 uint8_t TrimSetpoint[12]; /* Images of TrimDAC setpoints */ 154 uint16_t ChargeEnabled; /* Image of MISC2 Battery */ 155 /* Charge Enabled (0 or WRMISC2_CHARGE_ENABLE). */ 156 uint16_t WDInterval; /* Image of MISC2 watchdog interval control bits. */ 157 uint32_t I2CAdrs; 158 /* I2C device address for onboard EEPROM (board rev dependent). */ 159 /* short I2Cards; */ 160 lsampl_t ao_readback[S626_DAC_CHANNELS]; 161} s626_private; 162 163typedef struct { 164 uint16_t RDDIn; 165 uint16_t WRDOut; 166 uint16_t RDEdgSel; 167 uint16_t WREdgSel; 168 uint16_t RDCapSel; 169 uint16_t WRCapSel; 170 uint16_t RDCapFlg; 171 uint16_t RDIntSel; 172 uint16_t WRIntSel; 173} dio_private; 174 175static dio_private dio_private_A = { 176 RDDIn:LP_RDDINA, 177 WRDOut:LP_WRDOUTA, 178 RDEdgSel:LP_RDEDGSELA, 179 WREdgSel:LP_WREDGSELA, 180 RDCapSel:LP_RDCAPSELA, 181 WRCapSel:LP_WRCAPSELA, 182 RDCapFlg:LP_RDCAPFLGA, 183 RDIntSel:LP_RDINTSELA, 184 WRIntSel:LP_WRINTSELA, 185}; 186 187static dio_private dio_private_B = { 188 RDDIn:LP_RDDINB, 189 WRDOut:LP_WRDOUTB, 190 RDEdgSel:LP_RDEDGSELB, 191 WREdgSel:LP_WREDGSELB, 192 RDCapSel:LP_RDCAPSELB, 193 WRCapSel:LP_WRCAPSELB, 194 RDCapFlg:LP_RDCAPFLGB, 195 RDIntSel:LP_RDINTSELB, 196 WRIntSel:LP_WRINTSELB, 197}; 198 199static dio_private dio_private_C = { 200 RDDIn:LP_RDDINC, 201 WRDOut:LP_WRDOUTC, 202 RDEdgSel:LP_RDEDGSELC, 203 WREdgSel:LP_WREDGSELC, 204 RDCapSel:LP_RDCAPSELC, 205 WRCapSel:LP_WRCAPSELC, 206 RDCapFlg:LP_RDCAPFLGC, 207 RDIntSel:LP_RDINTSELC, 208 WRIntSel:LP_WRINTSELC, 209}; 210 211/* to group dio devices (48 bits mask and data are not allowed ???) 212static dio_private *dio_private_word[]={ 213 &dio_private_A, 214 &dio_private_B, 215 &dio_private_C, 216}; 217*/ 218 219#define devpriv ((s626_private *)dev->private) 220#define diopriv ((dio_private *)s->private) 221 222COMEDI_PCI_INITCLEANUP_NOMODULE(driver_s626, s626_pci_table); 223 224/* ioctl routines */ 225static int s626_ai_insn_config(comedi_device * dev, comedi_subdevice * s, 226 comedi_insn * insn, lsampl_t * data); 227/* static int s626_ai_rinsn(comedi_device *dev,comedi_subdevice *s,comedi_insn *insn,lsampl_t *data); */ 228static int s626_ai_insn_read(comedi_device * dev, comedi_subdevice * s, 229 comedi_insn * insn, lsampl_t * data); 230static int s626_ai_cmd(comedi_device * dev, comedi_subdevice * s); 231static int s626_ai_cmdtest(comedi_device * dev, comedi_subdevice * s, 232 comedi_cmd * cmd); 233static int s626_ai_cancel(comedi_device * dev, comedi_subdevice * s); 234static int s626_ao_winsn(comedi_device * dev, comedi_subdevice * s, 235 comedi_insn * insn, lsampl_t * data); 236static int s626_ao_rinsn(comedi_device * dev, comedi_subdevice * s, 237 comedi_insn * insn, lsampl_t * data); 238static int s626_dio_insn_bits(comedi_device * dev, comedi_subdevice * s, 239 comedi_insn * insn, lsampl_t * data); 240static int s626_dio_insn_config(comedi_device * dev, comedi_subdevice * s, 241 comedi_insn * insn, lsampl_t * data); 242static int s626_dio_set_irq(comedi_device * dev, unsigned int chan); 243static int s626_dio_reset_irq(comedi_device * dev, unsigned int gruop, 244 unsigned int mask); 245static int s626_dio_clear_irq(comedi_device * dev); 246static int s626_enc_insn_config(comedi_device * dev, comedi_subdevice * s, 247 comedi_insn * insn, lsampl_t * data); 248static int s626_enc_insn_read(comedi_device * dev, comedi_subdevice * s, 249 comedi_insn * insn, lsampl_t * data); 250static int s626_enc_insn_write(comedi_device * dev, comedi_subdevice * s, 251 comedi_insn * insn, lsampl_t * data); 252static int s626_ns_to_timer(int *nanosec, int round_mode); 253static int s626_ai_load_polllist(uint8_t * ppl, comedi_cmd * cmd); 254static int s626_ai_inttrig(comedi_device * dev, comedi_subdevice * s, 255 unsigned int trignum); 256static irqreturn_t s626_irq_handler(int irq, void *d PT_REGS_ARG); 257static lsampl_t s626_ai_reg_to_uint(int data); 258/* static lsampl_t s626_uint_to_reg(comedi_subdevice *s, int data); */ 259 260/* end ioctl routines */ 261 262/* internal routines */ 263static void s626_dio_init(comedi_device * dev); 264static void ResetADC(comedi_device * dev, uint8_t * ppl); 265static void LoadTrimDACs(comedi_device * dev); 266static void WriteTrimDAC(comedi_device * dev, uint8_t LogicalChan, 267 uint8_t DacData); 268static uint8_t I2Cread(comedi_device * dev, uint8_t addr); 269static uint32_t I2Chandshake(comedi_device * dev, uint32_t val); 270static void SetDAC(comedi_device * dev, uint16_t chan, short dacdata); 271static void SendDAC(comedi_device * dev, uint32_t val); 272static void WriteMISC2(comedi_device * dev, uint16_t NewImage); 273static void DEBItransfer(comedi_device * dev); 274static uint16_t DEBIread(comedi_device * dev, uint16_t addr); 275static void DEBIwrite(comedi_device * dev, uint16_t addr, uint16_t wdata); 276static void DEBIreplace(comedi_device * dev, uint16_t addr, uint16_t mask, 277 uint16_t wdata); 278static void CloseDMAB(comedi_device * dev, DMABUF * pdma, size_t bsize); 279 280/* COUNTER OBJECT ------------------------------------------------ */ 281typedef struct enc_private_struct { 282 /* Pointers to functions that differ for A and B counters: */ 283 uint16_t(*GetEnable) (comedi_device * dev, struct enc_private_struct *); /* Return clock enable. */ 284 uint16_t(*GetIntSrc) (comedi_device * dev, struct enc_private_struct *); /* Return interrupt source. */ 285 uint16_t(*GetLoadTrig) (comedi_device * dev, struct enc_private_struct *); /* Return preload trigger source. */ 286 uint16_t(*GetMode) (comedi_device * dev, struct enc_private_struct *); /* Return standardized operating mode. */ 287 void (*PulseIndex) (comedi_device * dev, struct enc_private_struct *); /* Generate soft index strobe. */ 288 void (*SetEnable) (comedi_device * dev, struct enc_private_struct *, uint16_t enab); /* Program clock enable. */ 289 void (*SetIntSrc) (comedi_device * dev, struct enc_private_struct *, uint16_t IntSource); /* Program interrupt source. */ 290 void (*SetLoadTrig) (comedi_device * dev, struct enc_private_struct *, uint16_t Trig); /* Program preload trigger source. */ 291 void (*SetMode) (comedi_device * dev, struct enc_private_struct *, uint16_t Setup, uint16_t DisableIntSrc); /* Program standardized operating mode. */ 292 void (*ResetCapFlags) (comedi_device * dev, struct enc_private_struct *); /* Reset event capture flags. */ 293 294 uint16_t MyCRA; /* Address of CRA register. */ 295 uint16_t MyCRB; /* Address of CRB register. */ 296 uint16_t MyLatchLsw; /* Address of Latch least-significant-word */ 297 /* register. */ 298 uint16_t MyEventBits[4]; /* Bit translations for IntSrc -->RDMISC2. */ 299} enc_private; /* counter object */ 300 301#define encpriv ((enc_private *)(dev->subdevices+5)->private) 302 303/* counters routines */ 304static void s626_timer_load(comedi_device * dev, enc_private * k, int tick); 305static uint32_t ReadLatch(comedi_device * dev, enc_private * k); 306static void ResetCapFlags_A(comedi_device * dev, enc_private * k); 307static void ResetCapFlags_B(comedi_device * dev, enc_private * k); 308static uint16_t GetMode_A(comedi_device * dev, enc_private * k); 309static uint16_t GetMode_B(comedi_device * dev, enc_private * k); 310static void SetMode_A(comedi_device * dev, enc_private * k, uint16_t Setup, 311 uint16_t DisableIntSrc); 312static void SetMode_B(comedi_device * dev, enc_private * k, uint16_t Setup, 313 uint16_t DisableIntSrc); 314static void SetEnable_A(comedi_device * dev, enc_private * k, uint16_t enab); 315static void SetEnable_B(comedi_device * dev, enc_private * k, uint16_t enab); 316static uint16_t GetEnable_A(comedi_device * dev, enc_private * k); 317static uint16_t GetEnable_B(comedi_device * dev, enc_private * k); 318static void SetLatchSource(comedi_device * dev, enc_private * k, 319 uint16_t value); 320/* static uint16_t GetLatchSource(comedi_device *dev, enc_private *k ); */ 321static void SetLoadTrig_A(comedi_device * dev, enc_private * k, uint16_t Trig); 322static void SetLoadTrig_B(comedi_device * dev, enc_private * k, uint16_t Trig); 323static uint16_t GetLoadTrig_A(comedi_device * dev, enc_private * k); 324static uint16_t GetLoadTrig_B(comedi_device * dev, enc_private * k); 325static void SetIntSrc_B(comedi_device * dev, enc_private * k, 326 uint16_t IntSource); 327static void SetIntSrc_A(comedi_device * dev, enc_private * k, 328 uint16_t IntSource); 329static uint16_t GetIntSrc_A(comedi_device * dev, enc_private * k); 330static uint16_t GetIntSrc_B(comedi_device * dev, enc_private * k); 331/* static void SetClkMult(comedi_device *dev, enc_private *k, uint16_t value ) ; */ 332/* static uint16_t GetClkMult(comedi_device *dev, enc_private *k ) ; */ 333/* static void SetIndexPol(comedi_device *dev, enc_private *k, uint16_t value ); */ 334/* static uint16_t GetClkPol(comedi_device *dev, enc_private *k ) ; */ 335/* static void SetIndexSrc( comedi_device *dev,enc_private *k, uint16_t value ); */ 336/* static uint16_t GetClkSrc( comedi_device *dev,enc_private *k ); */ 337/* static void SetIndexSrc( comedi_device *dev,enc_private *k, uint16_t value ); */ 338/* static uint16_t GetIndexSrc( comedi_device *dev,enc_private *k ); */ 339static void PulseIndex_A(comedi_device * dev, enc_private * k); 340static void PulseIndex_B(comedi_device * dev, enc_private * k); 341static void Preload(comedi_device * dev, enc_private * k, uint32_t value); 342static void CountersInit(comedi_device * dev); 343/* end internal routines */ 344 345/* Counter objects constructor. */ 346 347/* Counter overflow/index event flag masks for RDMISC2. */ 348#define INDXMASK(C) ( 1 << ( ( (C) > 2 ) ? ( (C) * 2 - 1 ) : ( (C) * 2 + 4 ) ) ) 349#define OVERMASK(C) ( 1 << ( ( (C) > 2 ) ? ( (C) * 2 + 5 ) : ( (C) * 2 + 10 ) ) ) 350#define EVBITS(C) { 0, OVERMASK(C), INDXMASK(C), OVERMASK(C) | INDXMASK(C) } 351 352/* Translation table to map IntSrc into equivalent RDMISC2 event flag bits. */ 353/* static const uint16_t EventBits[][4] = { EVBITS(0), EVBITS(1), EVBITS(2), EVBITS(3), EVBITS(4), EVBITS(5) }; */ 354 355/* enc_private; */ 356static enc_private enc_private_data[] = { 357 { 358 GetEnable:GetEnable_A, 359 GetIntSrc:GetIntSrc_A, 360 GetLoadTrig:GetLoadTrig_A, 361 GetMode: GetMode_A, 362 PulseIndex:PulseIndex_A, 363 SetEnable:SetEnable_A, 364 SetIntSrc:SetIntSrc_A, 365 SetLoadTrig:SetLoadTrig_A, 366 SetMode: SetMode_A, 367 ResetCapFlags:ResetCapFlags_A, 368 MyCRA: LP_CR0A, 369 MyCRB: LP_CR0B, 370 MyLatchLsw:LP_CNTR0ALSW, 371 MyEventBits:EVBITS(0), 372 }, 373 { 374 GetEnable:GetEnable_A, 375 GetIntSrc:GetIntSrc_A, 376 GetLoadTrig:GetLoadTrig_A, 377 GetMode: GetMode_A, 378 PulseIndex:PulseIndex_A, 379 SetEnable:SetEnable_A, 380 SetIntSrc:SetIntSrc_A, 381 SetLoadTrig:SetLoadTrig_A, 382 SetMode: SetMode_A, 383 ResetCapFlags:ResetCapFlags_A, 384 MyCRA: LP_CR1A, 385 MyCRB: LP_CR1B, 386 MyLatchLsw:LP_CNTR1ALSW, 387 MyEventBits:EVBITS(1), 388 }, 389 { 390 GetEnable:GetEnable_A, 391 GetIntSrc:GetIntSrc_A, 392 GetLoadTrig:GetLoadTrig_A, 393 GetMode: GetMode_A, 394 PulseIndex:PulseIndex_A, 395 SetEnable:SetEnable_A, 396 SetIntSrc:SetIntSrc_A, 397 SetLoadTrig:SetLoadTrig_A, 398 SetMode: SetMode_A, 399 ResetCapFlags:ResetCapFlags_A, 400 MyCRA: LP_CR2A, 401 MyCRB: LP_CR2B, 402 MyLatchLsw:LP_CNTR2ALSW, 403 MyEventBits:EVBITS(2), 404 }, 405 { 406 GetEnable:GetEnable_B, 407 GetIntSrc:GetIntSrc_B, 408 GetLoadTrig:GetLoadTrig_B, 409 GetMode: GetMode_B, 410 PulseIndex:PulseIndex_B, 411 SetEnable:SetEnable_B, 412 SetIntSrc:SetIntSrc_B, 413 SetLoadTrig:SetLoadTrig_B, 414 SetMode: SetMode_B, 415 ResetCapFlags:ResetCapFlags_B, 416 MyCRA: LP_CR0A, 417 MyCRB: LP_CR0B, 418 MyLatchLsw:LP_CNTR0BLSW, 419 MyEventBits:EVBITS(3), 420 }, 421 { 422 GetEnable:GetEnable_B, 423 GetIntSrc:GetIntSrc_B, 424 GetLoadTrig:GetLoadTrig_B, 425 GetMode: GetMode_B, 426 PulseIndex:PulseIndex_B, 427 SetEnable:SetEnable_B, 428 SetIntSrc:SetIntSrc_B, 429 SetLoadTrig:SetLoadTrig_B, 430 SetMode: SetMode_B, 431 ResetCapFlags:ResetCapFlags_B, 432 MyCRA: LP_CR1A, 433 MyCRB: LP_CR1B, 434 MyLatchLsw:LP_CNTR1BLSW, 435 MyEventBits:EVBITS(4), 436 }, 437 { 438 GetEnable:GetEnable_B, 439 GetIntSrc:GetIntSrc_B, 440 GetLoadTrig:GetLoadTrig_B, 441 GetMode: GetMode_B, 442 PulseIndex:PulseIndex_B, 443 SetEnable:SetEnable_B, 444 SetIntSrc:SetIntSrc_B, 445 SetLoadTrig:SetLoadTrig_B, 446 SetMode: SetMode_B, 447 ResetCapFlags:ResetCapFlags_B, 448 MyCRA: LP_CR2A, 449 MyCRB: LP_CR2B, 450 MyLatchLsw:LP_CNTR2BLSW, 451 MyEventBits:EVBITS(5), 452 }, 453}; 454 455/* enab/disable a function or test status bit(s) that are accessed */ 456/* through Main Control Registers 1 or 2. */ 457#define MC_ENABLE( REGADRS, CTRLWORD ) writel( ( (uint32_t)( CTRLWORD ) << 16 ) | (uint32_t)( CTRLWORD ),devpriv->base_addr+( REGADRS ) ) 458 459#define MC_DISABLE( REGADRS, CTRLWORD ) writel( (uint32_t)( CTRLWORD ) << 16 , devpriv->base_addr+( REGADRS ) ) 460 461#define MC_TEST( REGADRS, CTRLWORD ) ( ( readl(devpriv->base_addr+( REGADRS )) & CTRLWORD ) != 0 ) 462 463/* #define WR7146(REGARDS,CTRLWORD) 464 writel(CTRLWORD,(uint32_t)(devpriv->base_addr+(REGARDS))) */ 465#define WR7146(REGARDS,CTRLWORD) writel(CTRLWORD,devpriv->base_addr+(REGARDS)) 466 467/* #define RR7146(REGARDS) 468 readl((uint32_t)(devpriv->base_addr+(REGARDS))) */ 469#define RR7146(REGARDS) readl(devpriv->base_addr+(REGARDS)) 470 471#define BUGFIX_STREG(REGADRS) ( REGADRS - 4 ) 472 473/* Write a time slot control record to TSL2. */ 474#define VECTPORT( VECTNUM ) (P_TSL2 + ( (VECTNUM) << 2 )) 475#define SETVECT( VECTNUM, VECTVAL ) WR7146(VECTPORT( VECTNUM ), (VECTVAL)) 476 477/* Code macros used for constructing I2C command bytes. */ 478#define I2C_B2(ATTR,VAL) ( ( (ATTR) << 6 ) | ( (VAL) << 24 ) ) 479#define I2C_B1(ATTR,VAL) ( ( (ATTR) << 4 ) | ( (VAL) << 16 ) ) 480#define I2C_B0(ATTR,VAL) ( ( (ATTR) << 2 ) | ( (VAL) << 8 ) ) 481 482static const comedi_lrange s626_range_table = { 2, { 483 RANGE(-5, 5), 484 RANGE(-10, 10), 485 } 486}; 487 488static int s626_attach(comedi_device * dev, comedi_devconfig * it) 489{ 490/* uint8_t PollList; */ 491/* uint16_t AdcData; */ 492/* uint16_t StartVal; */ 493/* uint16_t index; */ 494/* unsigned int data[16]; */ 495 int result; 496 int i; 497 int ret; 498 resource_size_t resourceStart; 499 dma_addr_t appdma; 500 comedi_subdevice *s; 501 struct pci_dev *pdev; 502 503 if (alloc_private(dev, sizeof(s626_private)) < 0) 504 return -ENOMEM; 505 506 for (pdev = pci_get_device(PCI_VENDOR_ID_S626, PCI_DEVICE_ID_S626, 507 NULL); pdev != NULL; 508 pdev = pci_get_device(PCI_VENDOR_ID_S626, 509 PCI_DEVICE_ID_S626, pdev)) { 510 if (it->options[0] || it->options[1]) { 511 if (pdev->bus->number == it->options[0] && 512 PCI_SLOT(pdev->devfn) == it->options[1]) { 513 /* matches requested bus/slot */ 514 break; 515 } 516 } else { 517 /* no bus/slot specified */ 518 break; 519 } 520 } 521 devpriv->pdev = pdev; 522 523 if (pdev == NULL) { 524 printk("s626_attach: Board not present!!!\n"); 525 return -ENODEV; 526 } 527 528 if ((result = comedi_pci_enable(pdev, "s626")) < 0) { 529 printk("s626_attach: comedi_pci_enable fails\n"); 530 return -ENODEV; 531 } 532 devpriv->got_regions = 1; 533 534 resourceStart = pci_resource_start(devpriv->pdev, 0); 535 536 devpriv->base_addr = ioremap(resourceStart, SIZEOF_ADDRESS_SPACE); 537 if (devpriv->base_addr == NULL) { 538 printk("s626_attach: IOREMAP failed\n"); 539 return -ENODEV; 540 } 541 542 if (devpriv->base_addr) { 543 /* disable master interrupt */ 544 writel(0, devpriv->base_addr + P_IER); 545 546 /* soft reset */ 547 writel(MC1_SOFT_RESET, devpriv->base_addr + P_MC1); 548 549 /* DMA FIXME DMA// */ 550 DEBUG("s626_attach: DMA ALLOCATION\n"); 551 552 /* adc buffer allocation */ 553 devpriv->allocatedBuf = 0; 554 555 if ((devpriv->ANABuf.LogicalBase = 556 pci_alloc_consistent(devpriv->pdev, DMABUF_SIZE, 557 &appdma)) == NULL) { 558 printk("s626_attach: DMA Memory mapping error\n"); 559 return -ENOMEM; 560 } 561 562 devpriv->ANABuf.PhysicalBase = appdma; 563 564 DEBUG("s626_attach: AllocDMAB ADC Logical=%p, bsize=%d, Physical=0x%x\n", devpriv->ANABuf.LogicalBase, DMABUF_SIZE, (uint32_t) devpriv->ANABuf.PhysicalBase); 565 566 devpriv->allocatedBuf++; 567 568 if ((devpriv->RPSBuf.LogicalBase = 569 pci_alloc_consistent(devpriv->pdev, DMABUF_SIZE, 570 &appdma)) == NULL) { 571 printk("s626_attach: DMA Memory mapping error\n"); 572 return -ENOMEM; 573 } 574 575 devpriv->RPSBuf.PhysicalBase = appdma; 576 577 DEBUG("s626_attach: AllocDMAB RPS Logical=%p, bsize=%d, Physical=0x%x\n", devpriv->RPSBuf.LogicalBase, DMABUF_SIZE, (uint32_t) devpriv->RPSBuf.PhysicalBase); 578 579 devpriv->allocatedBuf++; 580 581 } 582 583 dev->board_ptr = s626_boards; 584 dev->board_name = thisboard->name; 585 586 if (alloc_subdevices(dev, 6) < 0) 587 return -ENOMEM; 588 589 dev->iobase = (unsigned long)devpriv->base_addr; 590 dev->irq = devpriv->pdev->irq; 591 592 /* set up interrupt handler */ 593 if (dev->irq == 0) { 594 printk(" unknown irq (bad)\n"); 595 } else { 596 if ((ret = comedi_request_irq(dev->irq, s626_irq_handler, 597 IRQF_SHARED, "s626", dev)) < 0) { 598 printk(" irq not available\n"); 599 dev->irq = 0; 600 } 601 } 602 603 DEBUG("s626_attach: -- it opts %d,%d -- \n", 604 it->options[0], it->options[1]); 605 606 s = dev->subdevices + 0; 607 /* analog input subdevice */ 608 dev->read_subdev = s; 609 /* we support single-ended (ground) and differential */ 610 s->type = COMEDI_SUBD_AI; 611 s->subdev_flags = SDF_READABLE | SDF_DIFF | SDF_CMD_READ; 612 s->n_chan = thisboard->ai_chans; 613 s->maxdata = (0xffff >> 2); 614 s->range_table = &s626_range_table; 615 s->len_chanlist = thisboard->ai_chans; /* This is the maximum chanlist 616 length that the board can 617 handle */ 618 s->insn_config = s626_ai_insn_config; 619 s->insn_read = s626_ai_insn_read; 620 s->do_cmd = s626_ai_cmd; 621 s->do_cmdtest = s626_ai_cmdtest; 622 s->cancel = s626_ai_cancel; 623 624 s = dev->subdevices + 1; 625 /* analog output subdevice */ 626 s->type = COMEDI_SUBD_AO; 627 s->subdev_flags = SDF_WRITABLE | SDF_READABLE; 628 s->n_chan = thisboard->ao_chans; 629 s->maxdata = (0x3fff); 630 s->range_table = &range_bipolar10; 631 s->insn_write = s626_ao_winsn; 632 s->insn_read = s626_ao_rinsn; 633 634 s = dev->subdevices + 2; 635 /* digital I/O subdevice */ 636 s->type = COMEDI_SUBD_DIO; 637 s->subdev_flags = SDF_WRITABLE | SDF_READABLE; 638 s->n_chan = S626_DIO_CHANNELS; 639 s->maxdata = 1; 640 s->io_bits = 0xffff; 641 s->private = &dio_private_A; 642 s->range_table = &range_digital; 643 s->insn_config = s626_dio_insn_config; 644 s->insn_bits = s626_dio_insn_bits; 645 646 s = dev->subdevices + 3; 647 /* digital I/O subdevice */ 648 s->type = COMEDI_SUBD_DIO; 649 s->subdev_flags = SDF_WRITABLE | SDF_READABLE; 650 s->n_chan = 16; 651 s->maxdata = 1; 652 s->io_bits = 0xffff; 653 s->private = &dio_private_B; 654 s->range_table = &range_digital; 655 s->insn_config = s626_dio_insn_config; 656 s->insn_bits = s626_dio_insn_bits; 657 658 s = dev->subdevices + 4; 659 /* digital I/O subdevice */ 660 s->type = COMEDI_SUBD_DIO; 661 s->subdev_flags = SDF_WRITABLE | SDF_READABLE; 662 s->n_chan = 16; 663 s->maxdata = 1; 664 s->io_bits = 0xffff; 665 s->private = &dio_private_C; 666 s->range_table = &range_digital; 667 s->insn_config = s626_dio_insn_config; 668 s->insn_bits = s626_dio_insn_bits; 669 670 s = dev->subdevices + 5; 671 /* encoder (counter) subdevice */ 672 s->type = COMEDI_SUBD_COUNTER; 673 s->subdev_flags = SDF_WRITABLE | SDF_READABLE | SDF_LSAMPL; 674 s->n_chan = thisboard->enc_chans; 675 s->private = enc_private_data; 676 s->insn_config = s626_enc_insn_config; 677 s->insn_read = s626_enc_insn_read; 678 s->insn_write = s626_enc_insn_write; 679 s->maxdata = 0xffffff; 680 s->range_table = &range_unknown; 681 682 /* stop ai_command */ 683 devpriv->ai_cmd_running = 0; 684 685 if (devpriv->base_addr && (devpriv->allocatedBuf == 2)) { 686 dma_addr_t pPhysBuf; 687 uint16_t chan; 688 689 /* enab DEBI and audio pins, enable I2C interface. */ 690 MC_ENABLE(P_MC1, MC1_DEBI | MC1_AUDIO | MC1_I2C); 691 /* Configure DEBI operating mode. */ 692 WR7146(P_DEBICFG, DEBI_CFG_SLAVE16 /* Local bus is 16 */ 693 /* bits wide. */ 694 | (DEBI_TOUT << DEBI_CFG_TOUT_BIT) /* Declare DEBI */ 695 /* transfer timeout */ 696 /* interval. */ 697 | DEBI_SWAP /* Set up byte lane */ 698 /* steering. */ 699 | DEBI_CFG_INTEL); /* Intel-compatible */ 700 /* local bus (DEBI */ 701 /* never times out). */ 702 DEBUG("s626_attach: %d debi init -- %d\n", 703 DEBI_CFG_SLAVE16 | (DEBI_TOUT << DEBI_CFG_TOUT_BIT) | 704 DEBI_SWAP | DEBI_CFG_INTEL, 705 DEBI_CFG_INTEL | DEBI_CFG_TOQ | DEBI_CFG_INCQ | 706 DEBI_CFG_16Q); 707 708 /* DEBI INIT S626 WR7146( P_DEBICFG, DEBI_CFG_INTEL | DEBI_CFG_TOQ */ 709 /* | DEBI_CFG_INCQ| DEBI_CFG_16Q); //end */ 710 711 /* Paging is disabled. */ 712 WR7146(P_DEBIPAGE, DEBI_PAGE_DISABLE); /* Disable MMU paging. */ 713 714 /* Init GPIO so that ADC Start* is negated. */ 715 WR7146(P_GPIO, GPIO_BASE | GPIO1_HI); 716 717 /* IsBoardRevA is a boolean that indicates whether the board is RevA. 718 * 719 * VERSION 2.01 CHANGE: REV A & B BOARDS NOW SUPPORTED BY DYNAMIC 720 * EEPROM ADDRESS SELECTION. Initialize the I2C interface, which 721 * is used to access the onboard serial EEPROM. The EEPROM's I2C 722 * DeviceAddress is hardwired to a value that is dependent on the 723 * 626 board revision. On all board revisions, the EEPROM stores 724 * TrimDAC calibration constants for analog I/O. On RevB and 725 * higher boards, the DeviceAddress is hardwired to 0 to enable 726 * the EEPROM to also store the PCI SubVendorID and SubDeviceID; 727 * this is the address at which the SAA7146 expects a 728 * configuration EEPROM to reside. On RevA boards, the EEPROM 729 * device address, which is hardwired to 4, prevents the SAA7146 730 * from retrieving PCI sub-IDs, so the SAA7146 uses its built-in 731 * default values, instead. 732 */ 733 734 /* devpriv->I2Cards= IsBoardRevA ? 0xA8 : 0xA0; // Set I2C EEPROM */ 735 /* DeviceType (0xA0) */ 736 /* and DeviceAddress<<1. */ 737 738 devpriv->I2CAdrs = 0xA0; /* I2C device address for onboard */ 739 /* eeprom(revb) */ 740 741 /* Issue an I2C ABORT command to halt any I2C operation in */ 742 /* progress and reset BUSY flag. */ 743 WR7146(P_I2CSTAT, I2C_CLKSEL | I2C_ABORT); 744 /* Write I2C control: abort any I2C activity. */ 745 MC_ENABLE(P_MC2, MC2_UPLD_IIC); 746 /* Invoke command upload */ 747 while ((RR7146(P_MC2) & MC2_UPLD_IIC) == 0); 748 /* and wait for upload to complete. */ 749 750 /* Per SAA7146 data sheet, write to STATUS reg twice to 751 * reset all I2C error flags. */ 752 for (i = 0; i < 2; i++) { 753 WR7146(P_I2CSTAT, I2C_CLKSEL); 754 /* Write I2C control: reset error flags. */ 755 MC_ENABLE(P_MC2, MC2_UPLD_IIC); /* Invoke command upload */ 756 while (!MC_TEST(P_MC2, MC2_UPLD_IIC)); 757 /* and wait for upload to complete. */ 758 } 759 760 /* Init audio interface functional attributes: set DAC/ADC 761 * serial clock rates, invert DAC serial clock so that 762 * DAC data setup times are satisfied, enable DAC serial 763 * clock out. 764 */ 765 766 WR7146(P_ACON2, ACON2_INIT); 767 768 /* Set up TSL1 slot list, which is used to control the 769 * accumulation of ADC data: RSD1 = shift data in on SD1. 770 * SIB_A1 = store data uint8_t at next available location in 771 * FB BUFFER1 register. */ 772 WR7146(P_TSL1, RSD1 | SIB_A1); 773 /* Fetch ADC high data uint8_t. */ 774 WR7146(P_TSL1 + 4, RSD1 | SIB_A1 | EOS); 775 /* Fetch ADC low data uint8_t; end of TSL1. */ 776 777 /* enab TSL1 slot list so that it executes all the time. */ 778 WR7146(P_ACON1, ACON1_ADCSTART); 779 780 /* Initialize RPS registers used for ADC. */ 781 782 /* Physical start of RPS program. */ 783 WR7146(P_RPSADDR1, (uint32_t) devpriv->RPSBuf.PhysicalBase); 784 785 WR7146(P_RPSPAGE1, 0); 786 /* RPS program performs no explicit mem writes. */ 787 WR7146(P_RPS1_TOUT, 0); /* Disable RPS timeouts. */ 788 789 /* SAA7146 BUG WORKAROUND. Initialize SAA7146 ADC interface 790 * to a known state by invoking ADCs until FB BUFFER 1 791 * register shows that it is correctly receiving ADC data. 792 * This is necessary because the SAA7146 ADC interface does 793 * not start up in a defined state after a PCI reset. 794 */ 795 796/* PollList = EOPL; // Create a simple polling */ 797/* // list for analog input */ 798/* // channel 0. */ 799/* ResetADC( dev, &PollList ); */ 800 801/* s626_ai_rinsn(dev,dev->subdevices,NULL,data); //( &AdcData ); // */ 802/* //Get initial ADC */ 803/* //value. */ 804 805/* StartVal = data[0]; */ 806 807/* // VERSION 2.01 CHANGE: TIMEOUT ADDED TO PREVENT HANGED EXECUTION. */ 808/* // Invoke ADCs until the new ADC value differs from the initial */ 809/* // value or a timeout occurs. The timeout protects against the */ 810/* // possibility that the driver is restarting and the ADC data is a */ 811/* // fixed value resulting from the applied ADC analog input being */ 812/* // unusually quiet or at the rail. */ 813 814/* for ( index = 0; index < 500; index++ ) */ 815/* { */ 816/* s626_ai_rinsn(dev,dev->subdevices,NULL,data); */ 817/* AdcData = data[0]; //ReadADC( &AdcData ); */ 818/* if ( AdcData != StartVal ) */ 819/* break; */ 820/* } */ 821 822 /* end initADC */ 823 824 /* init the DAC interface */ 825 826 /* Init Audio2's output DMAC attributes: burst length = 1 827 * DWORD, threshold = 1 DWORD. 828 */ 829 WR7146(P_PCI_BT_A, 0); 830 831 /* Init Audio2's output DMA physical addresses. The protection 832 * address is set to 1 DWORD past the base address so that a 833 * single DWORD will be transferred each time a DMA transfer is 834 * enabled. */ 835 836 pPhysBuf = 837 devpriv->ANABuf.PhysicalBase + 838 (DAC_WDMABUF_OS * sizeof(uint32_t)); 839 840 WR7146(P_BASEA2_OUT, (uint32_t) pPhysBuf); /* Buffer base adrs. */ 841 WR7146(P_PROTA2_OUT, (uint32_t) (pPhysBuf + sizeof(uint32_t))); /* Protection address. */ 842 843 /* Cache Audio2's output DMA buffer logical address. This is 844 * where DAC data is buffered for A2 output DMA transfers. */ 845 devpriv->pDacWBuf = 846 (uint32_t *) devpriv->ANABuf.LogicalBase + 847 DAC_WDMABUF_OS; 848 849 /* Audio2's output channels does not use paging. The protection 850 * violation handling bit is set so that the DMAC will 851 * automatically halt and its PCI address pointer will be reset 852 * when the protection address is reached. */ 853 854 WR7146(P_PAGEA2_OUT, 8); 855 856 /* Initialize time slot list 2 (TSL2), which is used to control 857 * the clock generation for and serialization of data to be sent 858 * to the DAC devices. Slot 0 is a NOP that is used to trap TSL 859 * execution; this permits other slots to be safely modified 860 * without first turning off the TSL sequencer (which is 861 * apparently impossible to do). Also, SD3 (which is driven by a 862 * pull-up resistor) is shifted in and stored to the MSB of 863 * FB_BUFFER2 to be used as evidence that the slot sequence has 864 * not yet finished executing. 865 */ 866 867 SETVECT(0, XSD2 | RSD3 | SIB_A2 | EOS); 868 /* Slot 0: Trap TSL execution, shift 0xFF into FB_BUFFER2. */ 869 870 /* Initialize slot 1, which is constant. Slot 1 causes a 871 * DWORD to be transferred from audio channel 2's output FIFO 872 * to the FIFO's output buffer so that it can be serialized 873 * and sent to the DAC during subsequent slots. All remaining 874 * slots are dynamically populated as required by the target 875 * DAC device. 876 */ 877 SETVECT(1, LF_A2); 878 /* Slot 1: Fetch DWORD from Audio2's output FIFO. */ 879 880 /* Start DAC's audio interface (TSL2) running. */ 881 WR7146(P_ACON1, ACON1_DACSTART); 882 883 /* end init DAC interface */ 884 885 /* Init Trim DACs to calibrated values. Do it twice because the 886 * SAA7146 audio channel does not always reset properly and 887 * sometimes causes the first few TrimDAC writes to malfunction. 888 */ 889 890 LoadTrimDACs(dev); 891 LoadTrimDACs(dev); /* Insurance. */ 892 893 /* Manually init all gate array hardware in case this is a soft 894 * reset (we have no way of determining whether this is a warm 895 * or cold start). This is necessary because the gate array will 896 * reset only in response to a PCI hard reset; there is no soft 897 * reset function. */ 898 899 /* Init all DAC outputs to 0V and init all DAC setpoint and 900 * polarity images. 901 */ 902 for (chan = 0; chan < S626_DAC_CHANNELS; chan++) 903 SetDAC(dev, chan, 0); 904 905 /* Init image of WRMISC2 Battery Charger Enabled control bit. 906 * This image is used when the state of the charger control bit, 907 * which has no direct hardware readback mechanism, is queried. 908 */ 909 devpriv->ChargeEnabled = 0; 910 911 /* Init image of watchdog timer interval in WRMISC2. This image 912 * maintains the value of the control bits of MISC2 are 913 * continuously reset to zero as long as the WD timer is disabled. 914 */ 915 devpriv->WDInterval = 0; 916 917 /* Init Counter Interrupt enab mask for RDMISC2. This mask is 918 * applied against MISC2 when testing to determine which timer 919 * events are requesting interrupt service. 920 */ 921 devpriv->CounterIntEnabs = 0; 922 923 /* Init counters. */ 924 CountersInit(dev); 925 926 /* Without modifying the state of the Battery Backup enab, disable 927 * the watchdog timer, set DIO channels 0-5 to operate in the 928 * standard DIO (vs. counter overflow) mode, disable the battery 929 * charger, and reset the watchdog interval selector to zero. 930 */ 931 WriteMISC2(dev, (uint16_t) (DEBIread(dev, 932 LP_RDMISC2) & MISC2_BATT_ENABLE)); 933 934 /* Initialize the digital I/O subsystem. */ 935 s626_dio_init(dev); 936 937 /* enable interrupt test */ 938 /* writel(IRQ_GPIO3 | IRQ_RPS1,devpriv->base_addr+P_IER); */ 939 } 940 941 DEBUG("s626_attach: comedi%d s626 attached %04x\n", dev->minor, 942 (uint32_t) devpriv->base_addr); 943 944 return 1; 945} 946 947static lsampl_t s626_ai_reg_to_uint(int data) 948{ 949 lsampl_t tempdata; 950 951 tempdata = (data >> 18); 952 if (tempdata & 0x2000) 953 tempdata &= 0x1fff; 954 else 955 tempdata += (1 << 13); 956 957 return tempdata; 958} 959 960/* static lsampl_t s626_uint_to_reg(comedi_subdevice *s, int data){ */ 961/* return 0; */ 962/* } */ 963 964static irqreturn_t s626_irq_handler(int irq, void *d PT_REGS_ARG) 965{ 966 comedi_device *dev = d; 967 comedi_subdevice *s; 968 comedi_cmd *cmd; 969 enc_private *k; 970 unsigned long flags; 971 int32_t *readaddr; 972 uint32_t irqtype, irqstatus; 973 int i = 0; 974 sampl_t tempdata; 975 uint8_t group; 976 uint16_t irqbit; 977 978 DEBUG("s626_irq_handler: interrupt request recieved!!!\n"); 979 980 if (dev->attached == 0) 981 return IRQ_NONE; 982 /* lock to avoid race with comedi_poll */ 983 comedi_spin_lock_irqsave(&dev->spinlock, flags); 984 985 /* save interrupt enable register state */ 986 irqstatus = readl(devpriv->base_addr + P_IER); 987 988 /* read interrupt type */ 989 irqtype = readl(devpriv->base_addr + P_ISR); 990 991 /* disable master interrupt */ 992 writel(0, devpriv->base_addr + P_IER); 993 994 /* clear interrupt */ 995 writel(irqtype, devpriv->base_addr + P_ISR); 996 997 /* do somethings */ 998 DEBUG("s626_irq_handler: interrupt type %d\n", irqtype); 999 1000 switch (irqtype) { 1001 case IRQ_RPS1: /* end_of_scan occurs */ 1002 1003 DEBUG("s626_irq_handler: RPS1 irq detected\n"); 1004 1005 /* manage ai subdevice */ 1006 s = dev->subdevices; 1007 cmd = &(s->async->cmd); 1008 1009 /* Init ptr to DMA buffer that holds new ADC data. We skip the 1010 * first uint16_t in the buffer because it contains junk data from 1011 * the final ADC of the previous poll list scan. 1012 */ 1013 readaddr = (int32_t *) devpriv->ANABuf.LogicalBase + 1; 1014 1015 /* get the data and hand it over to comedi */ 1016 for (i = 0; i < (s->async->cmd.chanlist_len); i++) { 1017 /* Convert ADC data to 16-bit integer values and copy to application */ 1018 /* buffer. */ 1019 tempdata = s626_ai_reg_to_uint((int)*readaddr); 1020 readaddr++; 1021 1022 /* put data into read buffer */ 1023 /* comedi_buf_put(s->async, tempdata); */ 1024 if (cfc_write_to_buffer(s, tempdata) == 0) 1025 printk("s626_irq_handler: cfc_write_to_buffer error!\n"); 1026 1027 DEBUG("s626_irq_handler: ai channel %d acquired: %d\n", 1028 i, tempdata); 1029 } 1030 1031 /* end of scan occurs */ 1032 s->async->events |= COMEDI_CB_EOS; 1033 1034 if (!(devpriv->ai_continous)) 1035 devpriv->ai_sample_count--; 1036 if (devpriv->ai_sample_count <= 0) { 1037 devpriv->ai_cmd_running = 0; 1038 1039 /* Stop RPS program. */ 1040 MC_DISABLE(P_MC1, MC1_ERPS1); 1041 1042 /* send end of acquisition */ 1043 s->async->events |= COMEDI_CB_EOA; 1044 1045 /* disable master interrupt */ 1046 irqstatus = 0; 1047 } 1048 1049 if (devpriv->ai_cmd_running && cmd->scan_begin_src == TRIG_EXT) { 1050 DEBUG("s626_irq_handler: enable interrupt on dio channel %d\n", cmd->scan_begin_arg); 1051 1052 s626_dio_set_irq(dev, cmd->scan_begin_arg); 1053 1054 DEBUG("s626_irq_handler: External trigger is set!!!\n"); 1055 } 1056 /* tell comedi that data is there */ 1057 DEBUG("s626_irq_handler: events %d\n", s->async->events); 1058 comedi_event(dev, s); 1059 break; 1060 case IRQ_GPIO3: /* check dio and conter interrupt */ 1061 1062 DEBUG("s626_irq_handler: GPIO3 irq detected\n"); 1063 1064 /* manage ai subdevice */ 1065 s = dev->subdevices; 1066 cmd = &(s->async->cmd); 1067 1068 /* s626_dio_clear_irq(dev); */ 1069 1070 for (group = 0; group < S626_DIO_BANKS; group++) { 1071 irqbit = 0; 1072 /* read interrupt type */ 1073 irqbit = DEBIread(dev, 1074 ((dio_private *) (dev->subdevices + 2 + 1075 group)->private)->RDCapFlg); 1076 1077 /* check if interrupt is generated from dio channels */ 1078 if (irqbit) { 1079 s626_dio_reset_irq(dev, group, irqbit); 1080 DEBUG("s626_irq_handler: check interrupt on dio group %d %d\n", group, i); 1081 if (devpriv->ai_cmd_running) { 1082 /* check if interrupt is an ai acquisition start trigger */ 1083 if ((irqbit >> (cmd->start_arg - 1084 (16 * group))) 1085 == 1 1086 && cmd->start_src == TRIG_EXT) { 1087 DEBUG("s626_irq_handler: Edge capture interrupt recieved from channel %d\n", cmd->start_arg); 1088 1089 /* Start executing the RPS program. */ 1090 MC_ENABLE(P_MC1, MC1_ERPS1); 1091 1092 DEBUG("s626_irq_handler: aquisition start triggered!!!\n"); 1093 1094 if (cmd->scan_begin_src == 1095 TRIG_EXT) { 1096 DEBUG("s626_ai_cmd: enable interrupt on dio channel %d\n", cmd->scan_begin_arg); 1097 1098 s626_dio_set_irq(dev, 1099 cmd-> 1100 scan_begin_arg); 1101 1102 DEBUG("s626_irq_handler: External scan trigger is set!!!\n"); 1103 } 1104 } 1105 if ((irqbit >> (cmd->scan_begin_arg - 1106 (16 * group))) 1107 == 1 1108 && cmd->scan_begin_src == 1109 TRIG_EXT) { 1110 DEBUG("s626_irq_handler: Edge capture interrupt recieved from channel %d\n", cmd->scan_begin_arg); 1111 1112 /* Trigger ADC scan loop start by setting RPS Signal 0. */ 1113 MC_ENABLE(P_MC2, MC2_ADC_RPS); 1114 1115 DEBUG("s626_irq_handler: scan triggered!!! %d\n", devpriv->ai_sample_count); 1116 if (cmd->convert_src == 1117 TRIG_EXT) { 1118 1119 DEBUG("s626_ai_cmd: enable interrupt on dio channel %d group %d\n", cmd->convert_arg - (16 * group), group); 1120 1121 devpriv-> 1122 ai_convert_count 1123 = 1124 cmd-> 1125 chanlist_len; 1126 1127 s626_dio_set_irq(dev, 1128 cmd-> 1129 convert_arg); 1130 1131 DEBUG("s626_irq_handler: External convert trigger is set!!!\n"); 1132 } 1133 1134 if (cmd->convert_src == 1135 TRIG_TIMER) { 1136 k = &encpriv[5]; 1137 devpriv-> 1138 ai_convert_count 1139 = 1140 cmd-> 1141 chanlist_len; 1142 k->SetEnable(dev, k, 1143 CLKENAB_ALWAYS); 1144 } 1145 } 1146 if ((irqbit >> (cmd->convert_arg - 1147 (16 * group))) 1148 == 1 1149 && cmd->convert_src == 1150 TRIG_EXT) { 1151 DEBUG("s626_irq_handler: Edge capture interrupt recieved from channel %d\n", cmd->convert_arg); 1152 1153 /* Trigger ADC scan loop start by setting RPS Signal 0. */ 1154 MC_ENABLE(P_MC2, MC2_ADC_RPS); 1155 1156 DEBUG("s626_irq_handler: adc convert triggered!!!\n"); 1157 1158 devpriv->ai_convert_count--; 1159 1160 if (devpriv->ai_convert_count > 1161 0) { 1162 1163 DEBUG("s626_ai_cmd: enable interrupt on dio channel %d group %d\n", cmd->convert_arg - (16 * group), group); 1164 1165 s626_dio_set_irq(dev, 1166 cmd-> 1167 convert_arg); 1168 1169 DEBUG("s626_irq_handler: External trigger is set!!!\n"); 1170 } 1171 } 1172 } 1173 break; 1174 } 1175 } 1176 1177 /* read interrupt type */ 1178 irqbit = DEBIread(dev, LP_RDMISC2); 1179 1180 /* check interrupt on counters */ 1181 DEBUG("s626_irq_handler: check counters interrupt %d\n", 1182 irqbit); 1183 1184 if (irqbit & IRQ_COINT1A) { 1185 DEBUG("s626_irq_handler: interrupt on counter 1A overflow\n"); 1186 k = &encpriv[0]; 1187 1188 /* clear interrupt capture flag */ 1189 k->ResetCapFlags(dev, k); 1190 } 1191 if (irqbit & IRQ_COINT2A) { 1192 DEBUG("s626_irq_handler: interrupt on counter 2A overflow\n"); 1193 k = &encpriv[1]; 1194 1195 /* clear interrupt capture flag */ 1196 k->ResetCapFlags(dev, k); 1197 } 1198 if (irqbit & IRQ_COINT3A) { 1199 DEBUG("s626_irq_handler: interrupt on counter 3A overflow\n"); 1200 k = &encpriv[2]; 1201 1202 /* clear interrupt capture flag */ 1203 k->ResetCapFlags(dev, k); 1204 } 1205 if (irqbit & IRQ_COINT1B) { 1206 DEBUG("s626_irq_handler: interrupt on counter 1B overflow\n"); 1207 k = &encpriv[3]; 1208 1209 /* clear interrupt capture flag */ 1210 k->ResetCapFlags(dev, k); 1211 } 1212 if (irqbit & IRQ_COINT2B) { 1213 DEBUG("s626_irq_handler: interrupt on counter 2B overflow\n"); 1214 k = &encpriv[4]; 1215 1216 /* clear interrupt capture flag */ 1217 k->ResetCapFlags(dev, k); 1218 1219 if (devpriv->ai_convert_count > 0) { 1220 devpriv->ai_convert_count--; 1221 if (devpriv->ai_convert_count == 0) 1222 k->SetEnable(dev, k, CLKENAB_INDEX); 1223 1224 if (cmd->convert_src == TRIG_TIMER) { 1225 DEBUG("s626_irq_handler: conver timer trigger!!! %d\n", devpriv->ai_convert_count); 1226 1227 /* Trigger ADC scan loop start by setting RPS Signal 0. */ 1228 MC_ENABLE(P_MC2, MC2_ADC_RPS); 1229 } 1230 } 1231 } 1232 if (irqbit & IRQ_COINT3B) { 1233 DEBUG("s626_irq_handler: interrupt on counter 3B overflow\n"); 1234 k = &encpriv[5]; 1235 1236 /* clear interrupt capture flag */ 1237 k->ResetCapFlags(dev, k); 1238 1239 if (cmd->scan_begin_src == TRIG_TIMER) { 1240 DEBUG("s626_irq_handler: scan timer trigger!!!\n"); 1241 1242 /* Trigger ADC scan loop start by setting RPS Signal 0. */ 1243 MC_ENABLE(P_MC2, MC2_ADC_RPS); 1244 } 1245 1246 if (cmd->convert_src == TRIG_TIMER) { 1247 DEBUG("s626_irq_handler: convert timer trigger is set\n"); 1248 k = &encpriv[4]; 1249 devpriv->ai_convert_count = cmd->chanlist_len; 1250 k->SetEnable(dev, k, CLKENAB_ALWAYS); 1251 } 1252 } 1253 } 1254 1255 /* enable interrupt */ 1256 writel(irqstatus, devpriv->base_addr + P_IER); 1257 1258 DEBUG("s626_irq_handler: exit interrupt service routine.\n"); 1259 1260 comedi_spin_unlock_irqrestore(&dev->spinlock, flags); 1261 return IRQ_HANDLED; 1262} 1263 1264static int s626_detach(comedi_device * dev) 1265{ 1266 if (devpriv) { 1267 /* stop ai_command */ 1268 devpriv->ai_cmd_running = 0; 1269 1270 if (devpriv->base_addr) { 1271 /* interrupt mask */ 1272 WR7146(P_IER, 0); /* Disable master interrupt. */ 1273 WR7146(P_ISR, IRQ_GPIO3 | IRQ_RPS1); /* Clear board's IRQ status flag. */ 1274 1275 /* Disable the watchdog timer and battery charger. */ 1276 WriteMISC2(dev, 0); 1277 1278 /* Close all interfaces on 7146 device. */ 1279 WR7146(P_MC1, MC1_SHUTDOWN); 1280 WR7146(P_ACON1, ACON1_BASE); 1281 1282 CloseDMAB(dev, &devpriv->RPSBuf, DMABUF_SIZE); 1283 CloseDMAB(dev, &devpriv->ANABuf, DMABUF_SIZE); 1284 } 1285 1286 if (dev->irq) { 1287 comedi_free_irq(dev->irq, dev); 1288 } 1289 1290 if (devpriv->base_addr) { 1291 iounmap(devpriv->base_addr); 1292 } 1293 1294 if (devpriv->pdev) { 1295 if (devpriv->got_regions) { 1296 comedi_pci_disable(devpriv->pdev); 1297 } 1298 pci_dev_put(devpriv->pdev); 1299 } 1300 } 1301 1302 DEBUG("s626_detach: S626 detached!\n"); 1303 1304 return 0; 1305} 1306 1307/* 1308 * this functions build the RPS program for hardware driven acquistion 1309 */ 1310void ResetADC(comedi_device * dev, uint8_t * ppl) 1311{ 1312 register uint32_t *pRPS; 1313 uint32_t JmpAdrs; 1314 uint16_t i; 1315 uint16_t n; 1316 uint32_t LocalPPL; 1317 comedi_cmd *cmd = &(dev->subdevices->async->cmd); 1318 1319 /* Stop RPS program in case it is currently running. */ 1320 MC_DISABLE(P_MC1, MC1_ERPS1); 1321 1322 /* Set starting logical address to write RPS commands. */ 1323 pRPS = (uint32_t *) devpriv->RPSBuf.LogicalBase; 1324 1325 /* Initialize RPS instruction pointer. */ 1326 WR7146(P_RPSADDR1, (uint32_t) devpriv->RPSBuf.PhysicalBase); 1327 1328 /* Construct RPS program in RPSBuf DMA buffer */ 1329 1330 if (cmd != NULL && cmd->scan_begin_src != TRIG_FOLLOW) { 1331 DEBUG("ResetADC: scan_begin pause inserted\n"); 1332 /* Wait for Start trigger. */ 1333 *pRPS++ = RPS_PAUSE | RPS_SIGADC; 1334 *pRPS++ = RPS_CLRSIGNAL | RPS_SIGADC; 1335 } 1336 1337 /* SAA7146 BUG WORKAROUND Do a dummy DEBI Write. This is necessary 1338 * because the first RPS DEBI Write following a non-RPS DEBI write 1339 * seems to always fail. If we don't do this dummy write, the ADC 1340 * gain might not be set to the value required for the first slot in 1341 * the poll list; the ADC gain would instead remain unchanged from 1342 * the previously programmed value. 1343 */ 1344 *pRPS++ = RPS_LDREG | (P_DEBICMD >> 2); 1345 /* Write DEBI Write command and address to shadow RAM. */ 1346 1347 *pRPS++ = DEBI_CMD_WRWORD | LP_GSEL; 1348 *pRPS++ = RPS_LDREG | (P_DEBIAD >> 2); 1349 /* Write DEBI immediate data to shadow RAM: */ 1350 1351 *pRPS++ = GSEL_BIPOLAR5V; 1352 /* arbitrary immediate data value. */ 1353 1354 *pRPS++ = RPS_CLRSIGNAL | RPS_DEBI; 1355 /* Reset "shadow RAM uploaded" flag. */ 1356 *pRPS++ = RPS_UPLOAD | RPS_DEBI; /* Invoke shadow RAM upload. */ 1357 *pRPS++ = RPS_PAUSE | RPS_DEBI; /* Wait for shadow upload to finish. */ 1358 1359 /* Digitize all slots in the poll list. This is implemented as a 1360 * for loop to limit the slot count to 16 in case the application 1361 * forgot to set the EOPL flag in the final slot. 1362 */ 1363 for (devpriv->AdcItems = 0; devpriv->AdcItems < 16; devpriv->AdcItems++) { 1364 /* Convert application's poll list item to private board class 1365 * format. Each app poll list item is an uint8_t with form 1366 * (EOPL,x,x,RANGE,CHAN<3:0>), where RANGE code indicates 0 = 1367 * +-10V, 1 = +-5V, and EOPL = End of Poll List marker. 1368 */ 1369 LocalPPL = 1370 (*ppl << 8) | (*ppl & 0x10 ? GSEL_BIPOLAR5V : 1371 GSEL_BIPOLAR10V); 1372 1373 /* Switch ADC analog gain. */ 1374 *pRPS++ = RPS_LDREG | (P_DEBICMD >> 2); /* Write DEBI command */ 1375 /* and address to */ 1376 /* shadow RAM. */ 1377 *pRPS++ = DEBI_CMD_WRWORD | LP_GSEL; 1378 *pRPS++ = RPS_LDREG | (P_DEBIAD >> 2); /* Write DEBI */ 1379 /* immediate data to */ 1380 /* shadow RAM. */ 1381 *pRPS++ = LocalPPL; 1382 *pRPS++ = RPS_CLRSIGNAL | RPS_DEBI; /* Reset "shadow RAM uploaded" */ 1383 /* flag. */ 1384 *pRPS++ = RPS_UPLOAD | RPS_DEBI; /* Invoke shadow RAM upload. */ 1385 *pRPS++ = RPS_PAUSE | RPS_DEBI; /* Wait for shadow upload to */ 1386 /* finish. */ 1387 1388 /* Select ADC analog input channel. */ 1389 *pRPS++ = RPS_LDREG | (P_DEBICMD >> 2); 1390 /* Write DEBI command and address to shadow RAM. */ 1391 *pRPS++ = DEBI_CMD_WRWORD | LP_ISEL; 1392 *pRPS++ = RPS_LDREG | (P_DEBIAD >> 2); 1393 /* Write DEBI immediate data to shadow RAM. */ 1394 *pRPS++ = LocalPPL; 1395 *pRPS++ = RPS_CLRSIGNAL | RPS_DEBI; 1396 /* Reset "shadow RAM uploaded" flag. */ 1397 1398 *pRPS++ = RPS_UPLOAD | RPS_DEBI; 1399 /* Invoke shadow RAM upload. */ 1400 1401 *pRPS++ = RPS_PAUSE | RPS_DEBI; 1402 /* Wait for shadow upload to finish. */ 1403 1404 /* Delay at least 10 microseconds for analog input settling. 1405 * Instead of padding with NOPs, we use RPS_JUMP instructions 1406 * here; this allows us to produce a longer delay than is 1407 * possible with NOPs because each RPS_JUMP flushes the RPS' 1408 * instruction prefetch pipeline. 1409 */ 1410 JmpAdrs = 1411 (uint32_t) devpriv->RPSBuf.PhysicalBase + 1412 (uint32_t) ((unsigned long)pRPS - 1413 (unsigned long)devpriv->RPSBuf.LogicalBase); 1414 for (i = 0; i < (10 * RPSCLK_PER_US / 2); i++) { 1415 JmpAdrs += 8; /* Repeat to implement time delay: */ 1416 *pRPS++ = RPS_JUMP; /* Jump to next RPS instruction. */ 1417 *pRPS++ = JmpAdrs; 1418 } 1419 1420 if (cmd != NULL && cmd->convert_src != TRIG_NOW) { 1421 DEBUG("ResetADC: convert pause inserted\n"); 1422 /* Wait for Start trigger. */ 1423 *pRPS++ = RPS_PAUSE | RPS_SIGADC; 1424 *pRPS++ = RPS_CLRSIGNAL | RPS_SIGADC; 1425 } 1426 /* Start ADC by pulsing GPIO1. */ 1427 *pRPS++ = RPS_LDREG | (P_GPIO >> 2); /* Begin ADC Start pulse. */ 1428 *pRPS++ = GPIO_BASE | GPIO1_LO; 1429 *pRPS++ = RPS_NOP; 1430 /* VERSION 2.03 CHANGE: STRETCH OUT ADC START PULSE. */ 1431 *pRPS++ = RPS_LDREG | (P_GPIO >> 2); /* End ADC Start pulse. */ 1432 *pRPS++ = GPIO_BASE | GPIO1_HI; 1433 1434 /* Wait for ADC to complete (GPIO2 is asserted high when ADC not 1435 * busy) and for data from previous conversion to shift into FB 1436 * BUFFER 1 register. 1437 */ 1438 *pRPS++ = RPS_PAUSE | RPS_GPIO2; /* Wait for ADC done. */ 1439 1440 /* Transfer ADC data from FB BUFFER 1 register to DMA buffer. */ 1441 *pRPS++ = RPS_STREG | (BUGFIX_STREG(P_FB_BUFFER1) >> 2); 1442 *pRPS++ = 1443 (uint32_t) devpriv->ANABuf.PhysicalBase + 1444 (devpriv->AdcItems << 2); 1445 1446 /* If this slot's EndOfPollList flag is set, all channels have */ 1447 /* now been processed. */ 1448 if (*ppl++ & EOPL) { 1449 devpriv->AdcItems++; /* Adjust poll list item count. */ 1450 break; /* Exit poll list processing loop. */ 1451 } 1452 } 1453 DEBUG("ResetADC: ADC items %d \n", devpriv->AdcItems); 1454 1455 /* VERSION 2.01 CHANGE: DELAY CHANGED FROM 250NS to 2US. Allow the 1456 * ADC to stabilize for 2 microseconds before starting the final 1457 * (dummy) conversion. This delay is necessary to allow sufficient 1458 * time between last conversion finished and the start of the dummy 1459 * conversion. Without this delay, the last conversion's data value 1460 * is sometimes set to the previous conversion's data value. 1461 */ 1462 for (n = 0; n < (2 * RPSCLK_PER_US); n++) 1463 *pRPS++ = RPS_NOP; 1464 1465 /* Start a dummy conversion to cause the data from the last 1466 * conversion of interest to be shifted in. 1467 */ 1468 *pRPS++ = RPS_LDREG | (P_GPIO >> 2); /* Begin ADC Start pulse. */ 1469 *pRPS++ = GPIO_BASE | GPIO1_LO; 1470 *pRPS++ = RPS_NOP; 1471 /* VERSION 2.03 CHANGE: STRETCH OUT ADC START PULSE. */ 1472 *pRPS++ = RPS_LDREG | (P_GPIO >> 2); /* End ADC Start pulse. */ 1473 *pRPS++ = GPIO_BASE | GPIO1_HI; 1474 1475 /* Wait for the data from the last conversion of interest to arrive 1476 * in FB BUFFER 1 register. 1477 */ 1478 *pRPS++ = RPS_PAUSE | RPS_GPIO2; /* Wait for ADC done. */ 1479 1480 /* Transfer final ADC data from FB BUFFER 1 register to DMA buffer. */ 1481 *pRPS++ = RPS_STREG | (BUGFIX_STREG(P_FB_BUFFER1) >> 2); /* */ 1482 *pRPS++ = 1483 (uint32_t) devpriv->ANABuf.PhysicalBase + 1484 (devpriv->AdcItems << 2); 1485 1486 /* Indicate ADC scan loop is finished. */ 1487 /* *pRPS++= RPS_CLRSIGNAL | RPS_SIGADC ; // Signal ReadADC() that scan is done. */ 1488 1489 /* invoke interrupt */ 1490 if (devpriv->ai_cmd_running == 1) { 1491 DEBUG("ResetADC: insert irq in ADC RPS task\n"); 1492 *pRPS++ = RPS_IRQ; 1493 } 1494 /* Restart RPS program at its beginning. */ 1495 *pRPS++ = RPS_JUMP; /* Branch to start of RPS program. */ 1496 *pRPS++ = (uint32_t) devpriv->RPSBuf.PhysicalBase; 1497 1498 /* End of RPS program build */ 1499} 1500 1501/* TO COMPLETE, IF NECESSARY */ 1502static int s626_ai_insn_config(comedi_device * dev, comedi_subdevice * s, 1503 comedi_insn * insn, lsampl_t * data) 1504{ 1505 1506 return -EINVAL; 1507} 1508 1509/* static int s626_ai_rinsn(comedi_device *dev,comedi_subdevice *s,comedi_insn *insn,lsampl_t *data) */ 1510/* { */ 1511/* register uint8_t i; */ 1512/* register int32_t *readaddr; */ 1513 1514/* DEBUG("as626_ai_rinsn: ai_rinsn enter \n"); */ 1515 1516/* Trigger ADC scan loop start by setting RPS Signal 0. */ 1517/* MC_ENABLE( P_MC2, MC2_ADC_RPS ); */ 1518 1519/* Wait until ADC scan loop is finished (RPS Signal 0 reset). */ 1520/* while ( MC_TEST( P_MC2, MC2_ADC_RPS ) ); */ 1521 1522/* Init ptr to DMA buffer that holds new ADC data. We skip the 1523 * first uint16_t in the buffer because it contains junk data from 1524 * the final ADC of the previous poll list scan. 1525 */ 1526/* readaddr = (uint32_t *)devpriv->ANABuf.LogicalBase + 1; */ 1527 1528/* Convert ADC data to 16-bit integer values and copy to application buffer. */ 1529/* for ( i = 0; i < devpriv->AdcItems; i++ ) { */ 1530/* *data = s626_ai_reg_to_uint( *readaddr++ ); */ 1531/* DEBUG("s626_ai_rinsn: data %d \n",*data); */ 1532/* data++; */ 1533/* } */ 1534 1535/* DEBUG("s626_ai_rinsn: ai_rinsn escape \n"); */ 1536/* return i; */ 1537/* } */ 1538 1539static int s626_ai_insn_read(comedi_device * dev, comedi_subdevice * s, 1540 comedi_insn * insn, lsampl_t * data) 1541{ 1542 uint16_t chan = CR_CHAN(insn->chanspec); 1543 uint16_t range = CR_RANGE(insn->chanspec); 1544 uint16_t AdcSpec = 0; 1545 uint32_t GpioImage; 1546 int n; 1547 1548 /* interrupt call test */ 1549/* writel(IRQ_GPIO3,devpriv->base_addr+P_PSR); */ 1550 /* Writing a logical 1 into any of the RPS_PSR bits causes the 1551 * corresponding interrupt to be generated if enabled 1552 */ 1553 1554 DEBUG("s626_ai_insn_read: entering\n"); 1555 1556 /* Convert application's ADC specification into form 1557 * appropriate for register programming. 1558 */ 1559 if (range == 0) 1560 AdcSpec = (chan << 8) | (GSEL_BIPOLAR5V); 1561 else 1562 AdcSpec = (chan << 8) | (GSEL_BIPOLAR10V); 1563 1564 /* Switch ADC analog gain. */ 1565 DEBIwrite(dev, LP_GSEL, AdcSpec); /* Set gain. */ 1566 1567 /* Select ADC analog input channel. */ 1568 DEBIwrite(dev, LP_ISEL, AdcSpec); /* Select channel. */ 1569 1570 for (n = 0; n < insn->n; n++) { 1571 1572 /* Delay 10 microseconds for analog input settling. */ 1573 comedi_udelay(10); 1574 1575 /* Start ADC by pulsing GPIO1 low. */ 1576 GpioImage = RR7146(P_GPIO); 1577 /* Assert ADC Start command */ 1578 WR7146(P_GPIO, GpioImage & ~GPIO1_HI); 1579 /* and stretch it out. */ 1580 WR7146(P_GPIO, GpioImage & ~GPIO1_HI); 1581 WR7146(P_GPIO, GpioImage & ~GPIO1_HI); 1582 /* Negate ADC Start command. */ 1583 WR7146(P_GPIO, GpioImage | GPIO1_HI); 1584 1585 /* Wait for ADC to complete (GPIO2 is asserted high when */ 1586 /* ADC not busy) and for data from previous conversion to */ 1587 /* shift into FB BUFFER 1 register. */ 1588 1589 /* Wait for ADC done. */ 1590 while (!(RR7146(P_PSR) & PSR_GPIO2)) ; 1591 1592 /* Fetch ADC data. */ 1593 if (n != 0) 1594 data[n - 1] = s626_ai_reg_to_uint(RR7146(P_FB_BUFFER1)); 1595 1596 /* Allow the ADC to stabilize for 4 microseconds before 1597 * starting the next (final) conversion. This delay is 1598 * necessary to allow sufficient time between last 1599 * conversion finished and the start of the next 1600 * conversion. Without this delay, the last conversion's 1601 * data value is sometimes set to the previous 1602 * conversion's data value. 1603 */ 1604 comedi_udelay(4); 1605 } 1606 1607 /* Start a dummy conversion to cause the data from the 1608 * previous conversion to be shifted in. */ 1609 GpioImage = RR7146(P_GPIO); 1610 1611 /* Assert ADC Start command */ 1612 WR7146(P_GPIO, GpioImage & ~GPIO1_HI); 1613 /* and stretch it out. */ 1614 WR7146(P_GPIO, GpioImage & ~GPIO1_HI); 1615 WR7146(P_GPIO, GpioImage & ~GPIO1_HI); 1616 /* Negate ADC Start command. */ 1617 WR7146(P_GPIO, GpioImage | GPIO1_HI); 1618 1619 /* Wait for the data to arrive in FB BUFFER 1 register. */ 1620 1621 /* Wait for ADC done. */ 1622 while (!(RR7146(P_PSR) & PSR_GPIO2)) ; 1623 1624 /* Fetch ADC data from audio interface's input shift register. */ 1625 1626 /* Fetch ADC data. */ 1627 if (n != 0) 1628 data[n - 1] = s626_ai_reg_to_uint(RR7146(P_FB_BUFFER1)); 1629 1630 DEBUG("s626_ai_insn_read: samples %d, data %d\n", n, data[n - 1]); 1631 1632 return n; 1633} 1634 1635static int s626_ai_load_polllist(uint8_t * ppl, comedi_cmd * cmd) 1636{ 1637 1638 int n; 1639 1640 for (n = 0; n < cmd->chanlist_len; n++) { 1641 if (CR_RANGE((cmd->chanlist)[n]) == 0) 1642 ppl[n] = (CR_CHAN((cmd->chanlist)[n])) | (RANGE_5V); 1643 else 1644 ppl[n] = (CR_CHAN((cmd->chanlist)[n])) | (RANGE_10V); 1645 } 1646 ppl[n - 1] |= EOPL; 1647 1648 return n; 1649} 1650 1651static int s626_ai_inttrig(comedi_device * dev, comedi_subdevice * s, 1652 unsigned int trignum) 1653{ 1654 if (trignum != 0) 1655 return -EINVAL; 1656 1657 DEBUG("s626_ai_inttrig: trigger adc start..."); 1658 1659 /* Start executing the RPS program. */ 1660 MC_ENABLE(P_MC1, MC1_ERPS1); 1661 1662 s->async->inttrig = NULL; 1663 1664 DEBUG(" done\n"); 1665 1666 return 1; 1667} 1668 1669/* TO COMPLETE */ 1670static int s626_ai_cmd(comedi_device * dev, comedi_subdevice * s) 1671{ 1672 1673 uint8_t ppl[16]; 1674 comedi_cmd *cmd = &s->async->cmd; 1675 enc_private *k; 1676 int tick; 1677 1678 DEBUG("s626_ai_cmd: entering command function\n"); 1679 1680 if (devpriv->ai_cmd_running) { 1681 printk("s626_ai_cmd: Another ai_cmd is running %d\n", 1682 dev->minor); 1683 return -EBUSY; 1684 } 1685 /* disable interrupt */ 1686 writel(0, devpriv->base_addr + P_IER); 1687 1688 /* clear interrupt request */ 1689 writel(IRQ_RPS1 | IRQ_GPIO3, devpriv->base_addr + P_ISR); 1690 1691 /* clear any pending interrupt */ 1692 s626_dio_clear_irq(dev); 1693 /* s626_enc_clear_irq(dev); */ 1694 1695 /* reset ai_cmd_running flag */ 1696 devpriv->ai_cmd_running = 0; 1697 1698 /* test if cmd is valid */ 1699 if (cmd == NULL) { 1700 DEBUG("s626_ai_cmd: NULL command\n"); 1701 return -EINVAL; 1702 } else { 1703 DEBUG("s626_ai_cmd: command recieved!!!\n"); 1704 } 1705 1706 if (dev->irq == 0) { 1707 comedi_error(dev, 1708 "s626_ai_cmd: cannot run command without an irq"); 1709 return -EIO; 1710 } 1711 1712 s626_ai_load_polllist(ppl, cmd); 1713 devpriv->ai_cmd_running = 1; 1714 devpriv->ai_convert_count = 0; 1715 1716 switch (cmd->scan_begin_src) { 1717 case TRIG_FOLLOW: 1718 break; 1719 case TRIG_TIMER: 1720 /* set a conter to generate adc trigger at scan_begin_arg interval */ 1721 k = &encpriv[5]; 1722 tick = s626_ns_to_timer((int *)&cmd->scan_begin_arg, 1723 cmd->flags & TRIG_ROUND_MASK); 1724 1725 /* load timer value and enable interrupt */ 1726 s626_timer_load(dev, k, tick); 1727 k->SetEnable(dev, k, CLKENAB_ALWAYS); 1728 1729 DEBUG("s626_ai_cmd: scan trigger timer is set with value %d\n", 1730 tick); 1731 1732 break; 1733 case TRIG_EXT: 1734 /* set the digital line and interrupt for scan trigger */ 1735 if (cmd->start_src != TRIG_EXT) 1736 s626_dio_set_irq(dev, cmd->scan_begin_arg); 1737 1738 DEBUG("s626_ai_cmd: External scan trigger is set!!!\n"); 1739 1740 break; 1741 } 1742 1743 switch (cmd->convert_src) { 1744 case TRIG_NOW: 1745 break; 1746 case TRIG_TIMER: 1747 /* set a conter to generate adc trigger at convert_arg interval */ 1748 k = &encpriv[4]; 1749 tick = s626_ns_to_timer((int *)&cmd->convert_arg, 1750 cmd->flags & TRIG_ROUND_MASK); 1751 1752 /* load timer value and enable interrupt */ 1753 s626_timer_load(dev, k, tick); 1754 k->SetEnable(dev, k, CLKENAB_INDEX); 1755 1756 DEBUG("s626_ai_cmd: convert trigger timer is set with value %d\n", tick); 1757 break; 1758 case TRIG_EXT: 1759 /* set the digital line and interrupt for convert trigger */ 1760 if (cmd->scan_begin_src != TRIG_EXT 1761 && cmd->start_src == TRIG_EXT) 1762 s626_dio_set_irq(dev, cmd->convert_arg); 1763 1764 DEBUG("s626_ai_cmd: External convert trigger is set!!!\n"); 1765 1766 break; 1767 } 1768 1769 switch (cmd->stop_src) { 1770 case TRIG_COUNT: 1771 /* data arrives as one packet */ 1772 devpriv->ai_sample_count = cmd->stop_arg; 1773 devpriv->ai_continous = 0; 1774 break; 1775 case TRIG_NONE: 1776 /* continous aquisition */ 1777 devpriv->ai_continous = 1; 1778 devpriv->ai_sample_count = 0; 1779 break; 1780 } 1781 1782 ResetADC(dev, ppl); 1783 1784 switch (cmd->start_src) { 1785 case TRIG_NOW: 1786 /* Trigger ADC scan loop start by setting RPS Signal 0. */ 1787 /* MC_ENABLE( P_MC2, MC2_ADC_RPS ); */ 1788 1789 /* Start executing the RPS program. */ 1790 MC_ENABLE(P_MC1, MC1_ERPS1); 1791 1792 DEBUG("s626_ai_cmd: ADC triggered\n"); 1793 s->async->inttrig = NULL; 1794 break; 1795 case TRIG_EXT: 1796 /* configure DIO channel for acquisition trigger */ 1797 s626_dio_set_irq(dev, cmd->start_arg); 1798 1799 DEBUG("s626_ai_cmd: External start trigger is set!!!\n"); 1800 1801 s->async->inttrig = NULL; 1802 break; 1803 case TRIG_INT: 1804 s->async->inttrig = s626_ai_inttrig; 1805 break; 1806 } 1807 1808 /* enable interrupt */ 1809 writel(IRQ_GPIO3 | IRQ_RPS1, devpriv->base_addr + P_IER); 1810 1811 DEBUG("s626_ai_cmd: command function terminated\n"); 1812 1813 return 0; 1814} 1815 1816static int s626_ai_cmdtest(comedi_device * dev, comedi_subdevice * s, 1817 comedi_cmd * cmd) 1818{ 1819 int err = 0; 1820 int tmp; 1821 1822 /* cmdtest tests a particular command to see if it is valid. Using 1823 * the cmdtest ioctl, a user can create a valid cmd and then have it 1824 * executes by the cmd ioctl. 1825 * 1826 * cmdtest returns 1,2,3,4 or 0, depending on which tests the 1827 * command passes. */ 1828 1829 /* step 1: make sure trigger sources are trivially valid */ 1830 1831 tmp = cmd->start_src; 1832 cmd->start_src &= TRIG_NOW | TRIG_INT | TRIG_EXT; 1833 if (!cmd->start_src || tmp != cmd->start_src) 1834 err++; 1835 1836 tmp = cmd->scan_begin_src; 1837 cmd->scan_begin_src &= TRIG_TIMER | TRIG_EXT | TRIG_FOLLOW; 1838 if (!cmd->scan_begin_src || tmp != cmd->scan_begin_src) 1839 err++; 1840 1841 tmp = cmd->convert_src; 1842 cmd->convert_src &= TRIG_TIMER | TRIG_EXT | TRIG_NOW; 1843 if (!cmd->convert_src || tmp != cmd->convert_src) 1844 err++; 1845 1846 tmp = cmd->scan_end_src; 1847 cmd->scan_end_src &= TRIG_COUNT; 1848 if (!cmd->scan_end_src || tmp != cmd->scan_end_src) 1849 err++; 1850 1851 tmp = cmd->stop_src; 1852 cmd->stop_src &= TRIG_COUNT | TRIG_NONE; 1853 if (!cmd->stop_src || tmp != cmd->stop_src) 1854 err++; 1855 1856 if (err) 1857 return 1; 1858 1859 /* step 2: make sure trigger sources are unique and mutually 1860 compatible */ 1861 1862 /* note that mutual compatiblity is not an issue here */ 1863 if (cmd->scan_begin_src != TRIG_TIMER && 1864 cmd->scan_begin_src != TRIG_EXT 1865 && cmd->scan_begin_src != TRIG_FOLLOW) 1866 err++; 1867 if (cmd->convert_src != TRIG_TIMER && 1868 cmd->convert_src != TRIG_EXT && cmd->convert_src != TRIG_NOW) 1869 err++; 1870 if (cmd->stop_src != TRIG_COUNT && cmd->stop_src != TRIG_NONE) 1871 err++; 1872 1873 if (err) 1874 return 2; 1875 1876 /* step 3: make sure arguments are trivially compatible */ 1877 1878 if (cmd->start_src != TRIG_EXT && cmd->start_arg != 0) { 1879 cmd->start_arg = 0; 1880 err++; 1881 } 1882 1883 if (cmd->start_src == TRIG_EXT && cmd->start_arg < 0) { 1884 cmd->start_arg = 0; 1885 err++; 1886 } 1887 1888 if (cmd->start_src == TRIG_EXT && cmd->start_arg > 39) { 1889 cmd->start_arg = 39; 1890 err++; 1891 } 1892 1893 if (cmd->scan_begin_src == TRIG_EXT && cmd->scan_begin_arg < 0) { 1894 cmd->scan_begin_arg = 0; 1895 err++; 1896 } 1897 1898 if (cmd->scan_begin_src == TRIG_EXT && cmd->scan_begin_arg > 39) { 1899 cmd->scan_begin_arg = 39; 1900 err++; 1901 } 1902 1903 if (cmd->convert_src == TRIG_EXT && cmd->convert_arg < 0) { 1904 cmd->convert_arg = 0; 1905 err++; 1906 } 1907 1908 if (cmd->convert_src == TRIG_EXT && cmd->convert_arg > 39) { 1909 cmd->convert_arg = 39; 1910 err++; 1911 } 1912#define MAX_SPEED 200000 /* in nanoseconds */ 1913#define MIN_SPEED 2000000000 /* in nanoseconds */ 1914 1915 if (cmd->scan_begin_src == TRIG_TIMER) { 1916 if (cmd->scan_begin_arg < MAX_SPEED) { 1917 cmd->scan_begin_arg = MAX_SPEED; 1918 err++; 1919 } 1920 if (cmd->scan_begin_arg > MIN_SPEED) { 1921 cmd->scan_begin_arg = MIN_SPEED; 1922 err++; 1923 } 1924 } else { 1925 /* external trigger */ 1926 /* should be level/edge, hi/lo specification here */ 1927 /* should specify multiple external triggers */ 1928/* if(cmd->scan_begin_arg>9){ */ 1929/* cmd->scan_begin_arg=9; */ 1930/* err++; */ 1931/* } */ 1932 } 1933 if (cmd->convert_src == TRIG_TIMER) { 1934 if (cmd->convert_arg < MAX_SPEED) { 1935 cmd->convert_arg = MAX_SPEED; 1936 err++; 1937 } 1938 if (cmd->convert_arg > MIN_SPEED) { 1939 cmd->convert_arg = MIN_SPEED; 1940 err++; 1941 } 1942 } else { 1943 /* external trigger */ 1944 /* see above */ 1945/* if(cmd->convert_arg>9){ */ 1946/* cmd->convert_arg=9; */ 1947/* err++; */ 1948/* } */ 1949 } 1950 1951 if (cmd->scan_end_arg != cmd->chanlist_len) { 1952 cmd->scan_end_arg = cmd->chanlist_len; 1953 err++; 1954 } 1955 if (cmd->stop_src == TRIG_COUNT) { 1956 if (cmd->stop_arg > 0x00ffffff) { 1957 cmd->stop_arg = 0x00ffffff; 1958 err++; 1959 } 1960 } else { 1961 /* TRIG_NONE */ 1962 if (cmd->stop_arg != 0) { 1963 cmd->stop_arg = 0; 1964 err++; 1965 } 1966 } 1967 1968 if (err) 1969 return 3; 1970 1971 /* step 4: fix up any arguments */ 1972 1973 if (cmd->scan_begin_src == TRIG_TIMER) { 1974 tmp = cmd->scan_begin_arg; 1975 s626_ns_to_timer((int *)&cmd->scan_begin_arg, 1976 cmd->flags & TRIG_ROUND_MASK); 1977 if (tmp != cmd->scan_begin_arg) 1978 err++; 1979 } 1980 if (cmd->convert_src == TRIG_TIMER) { 1981 tmp = cmd->convert_arg; 1982 s626_ns_to_timer((int *)&cmd->convert_arg, 1983 cmd->flags & TRIG_ROUND_MASK); 1984 if (tmp != cmd->convert_arg) 1985 err++; 1986 if (cmd->scan_begin_src == TRIG_TIMER && 1987 cmd->scan_begin_arg < 1988 cmd->convert_arg * cmd->scan_end_arg) { 1989 cmd->scan_begin_arg = 1990 cmd->convert_arg * cmd->scan_end_arg; 1991 err++; 1992 } 1993 } 1994 1995 if (err) 1996 return 4; 1997 1998 return 0; 1999} 2000 2001static int s626_ai_cancel(comedi_device * dev, comedi_subdevice * s) 2002{ 2003 /* Stop RPS program in case it is currently running. */ 2004 MC_DISABLE(P_MC1, MC1_ERPS1); 2005 2006 /* disable master interrupt */ 2007 writel(0, devpriv->base_addr + P_IER); 2008 2009 devpriv->ai_cmd_running = 0; 2010 2011 return 0; 2012} 2013 2014/* This function doesn't require a particular form, this is just what 2015 * happens to be used in some of the drivers. It should convert ns 2016 * nanoseconds to a counter value suitable for programming the device. 2017 * Also, it should adjust ns so that it cooresponds to the actual time 2018 * that the device will use. */ 2019static int s626_ns_to_timer(int *nanosec, int round_mode) 2020{ 2021 int divider, base; 2022 2023 base = 500; /* 2MHz internal clock */ 2024 2025 switch (round_mode) { 2026 case TRIG_ROUND_NEAREST: 2027 default: 2028 divider = (*nanosec + base / 2) / base; 2029 break; 2030 case TRIG_ROUND_DOWN: 2031 divider = (*nanosec) / base; 2032 break; 2033 case TRIG_ROUND_UP: 2034 divider = (*nanosec + base - 1) / base; 2035 break; 2036 } 2037 2038 *nanosec = base * divider; 2039 return divider - 1; 2040} 2041 2042static int s626_ao_winsn(comedi_device * dev, comedi_subdevice * s, 2043 comedi_insn * insn, lsampl_t * data) 2044{ 2045 2046 int i; 2047 uint16_t chan = CR_CHAN(insn->chanspec); 2048 int16_t dacdata; 2049 2050 for (i = 0; i < insn->n; i++) { 2051 dacdata = (int16_t) data[i]; 2052 devpriv->ao_readback[CR_CHAN(insn->chanspec)] = data[i]; 2053 dacdata -= (0x1fff); 2054 2055 SetDAC(dev, chan, dacdata); 2056 } 2057 2058 return i; 2059} 2060 2061static int s626_ao_rinsn(comedi_device * dev, comedi_subdevice * s, 2062 comedi_insn * insn, lsampl_t * data) 2063{ 2064 int i; 2065 2066 for (i = 0; i < insn->n; i++) { 2067 data[i] = devpriv->ao_readback[CR_CHAN(insn->chanspec)]; 2068 } 2069 2070 return i; 2071} 2072 2073/* *************** DIGITAL I/O FUNCTIONS *************** 2074 * All DIO functions address a group of DIO channels by means of 2075 * "group" argument. group may be 0, 1 or 2, which correspond to DIO 2076 * ports A, B and C, respectively. 2077 */ 2078 2079static void s626_dio_init(comedi_device * dev) 2080{ 2081 uint16_t group; 2082 comedi_subdevice *s; 2083 2084 /* Prepare to treat writes to WRCapSel as capture disables. */ 2085 DEBIwrite(dev, LP_MISC1, MISC1_NOEDCAP); 2086 2087 /* For each group of sixteen channels ... */ 2088 for (group = 0; group < S626_DIO_BANKS; group++) { 2089 s = dev->subdevices + 2 + group; 2090 DEBIwrite(dev, diopriv->WRIntSel, 0); /* Disable all interrupts. */ 2091 DEBIwrite(dev, diopriv->WRCapSel, 0xFFFF); /* Disable all event */ 2092 /* captures. */ 2093 DEBIwrite(dev, diopriv->WREdgSel, 0); /* Init all DIOs to */ 2094 /* default edge */ 2095 /* polarity. */ 2096 DEBIwrite(dev, diopriv->WRDOut, 0); /* Program all outputs */ 2097 /* to inactive state. */ 2098 } 2099 DEBUG("s626_dio_init: DIO initialized \n"); 2100} 2101 2102/* DIO devices are slightly special. Although it is possible to 2103 * implement the insn_read/insn_write interface, it is much more 2104 * useful to applications if you implement the insn_bits interface. 2105 * This allows packed reading/writing of the DIO channels. The comedi 2106 * core can convert between insn_bits and insn_read/write */ 2107 2108static int s626_dio_insn_bits(comedi_device * dev, comedi_subdevice * s, 2109 comedi_insn * insn, lsampl_t * data) 2110{ 2111 2112 /* Length of data must be 2 (mask and new data, see below) */ 2113 if (insn->n == 0) { 2114 return 0; 2115 } 2116 if (insn->n != 2) { 2117 printk("comedi%d: s626: s626_dio_insn_bits(): Invalid instruction length\n", dev->minor); 2118 return -EINVAL; 2119 } 2120 2121 /* 2122 * The insn data consists of a mask in data[0] and the new data in 2123 * data[1]. The mask defines which bits we are concerning about. 2124 * The new data must be anded with the mask. Each channel 2125 * corresponds to a bit. 2126 */ 2127 if (data[0]) { 2128 /* Check if requested ports are configured for output */ 2129 if ((s->io_bits & data[0]) != data[0]) 2130 return -EIO; 2131 2132 s->state &= ~data[0]; 2133 s->state |= data[0] & data[1]; 2134 2135 /* Write out the new digital output lines */ 2136 2137 DEBIwrite(dev, diopriv->WRDOut, s->state); 2138 } 2139 data[1] = DEBIread(dev, diopriv->RDDIn); 2140 2141 return 2; 2142} 2143 2144static int s626_dio_insn_config(comedi_device * dev, comedi_subdevice * s, 2145 comedi_insn * insn, lsampl_t * data) 2146{ 2147 2148 switch (data[0]) { 2149 case INSN_CONFIG_DIO_QUERY: 2150 data[1] = 2151 (s->io_bits & (1 << CR_CHAN(insn-> 2152 chanspec))) ? COMEDI_OUTPUT : 2153 COMEDI_INPUT; 2154 return insn->n; 2155 break; 2156 case COMEDI_INPUT: 2157 s->io_bits &= ~(1 << CR_CHAN(insn->chanspec)); 2158 break; 2159 case COMEDI_OUTPUT: 2160 s->io_bits |= 1 << CR_CHAN(insn->chanspec); 2161 break; 2162 default: 2163 return -EINVAL; 2164 break; 2165 } 2166 DEBIwrite(dev, diopriv->WRDOut, s->io_bits); 2167 2168 return 1; 2169} 2170 2171static int s626_dio_set_irq(comedi_device * dev, unsigned int chan) 2172{ 2173 unsigned int group; 2174 unsigned int bitmask; 2175 unsigned int status; 2176 2177 /* select dio bank */ 2178 group = chan / 16; 2179 bitmask = 1 << (chan - (16 * group)); 2180 DEBUG("s626_dio_set_irq: enable interrupt on dio channel %d group %d\n", 2181 chan - (16 * group), group); 2182 2183 /* set channel to capture positive edge */ 2184 status = DEBIread(dev, 2185 ((dio_private *) (dev->subdevices + 2 + 2186 group)->private)->RDEdgSel); 2187 DEBIwrite(dev, 2188 ((dio_private *) (dev->subdevices + 2 + 2189 group)->private)->WREdgSel, bitmask | status); 2190 2191 /* enable interrupt on selected channel */ 2192 status = DEBIread(dev, 2193 ((dio_private *) (dev->subdevices + 2 + 2194 group)->private)->RDIntSel); 2195 DEBIwrite(dev, 2196 ((dio_private *) (dev->subdevices + 2 + 2197 group)->private)->WRIntSel, bitmask | status); 2198 2199 /* enable edge capture write command */ 2200 DEBIwrite(dev, LP_MISC1, MISC1_EDCAP); 2201 2202 /* enable edge capture on selected channel */ 2203 status = DEBIread(dev, 2204 ((dio_private *) (dev->subdevices + 2 + 2205 group)->private)->RDCapSel); 2206 DEBIwrite(dev, 2207 ((dio_private *) (dev->subdevices + 2 + 2208 group)->private)->WRCapSel, bitmask | status); 2209 2210 return 0; 2211} 2212 2213static int s626_dio_reset_irq(comedi_device * dev, unsigned int group, 2214 unsigned int mask) 2215{ 2216 DEBUG("s626_dio_reset_irq: disable interrupt on dio channel %d group %d\n", mask, group); 2217 2218 /* disable edge capture write command */ 2219 DEBIwrite(dev, LP_MISC1, MISC1_NOEDCAP); 2220 2221 /* enable edge capture on selected channel */ 2222 DEBIwrite(dev, 2223 ((dio_private *) (dev->subdevices + 2 + 2224 group)->private)->WRCapSel, mask); 2225 2226 return 0; 2227} 2228 2229static int s626_dio_clear_irq(comedi_device * dev) 2230{ 2231 unsigned int group; 2232 2233 /* disable edge capture write command */ 2234 DEBIwrite(dev, LP_MISC1, MISC1_NOEDCAP); 2235 2236 for (group = 0; group < S626_DIO_BANKS; group++) { 2237 /* clear pending events and interrupt */ 2238 DEBIwrite(dev, 2239 ((dio_private *) (dev->subdevices + 2 + 2240 group)->private)->WRCapSel, 0xffff); 2241 } 2242 2243 return 0; 2244} 2245 2246/* Now this function initializes the value of the counter (data[0]) 2247 and set the subdevice. To complete with trigger and interrupt 2248 configuration */ 2249static int s626_enc_insn_config(comedi_device * dev, comedi_subdevice * s, 2250 comedi_insn * insn, lsampl_t * data) 2251{ 2252 uint16_t Setup = (LOADSRC_INDX << BF_LOADSRC) | /* Preload upon */ 2253 /* index. */ 2254 (INDXSRC_SOFT << BF_INDXSRC) | /* Disable hardware index. */ 2255 (CLKSRC_COUNTER << BF_CLKSRC) | /* Operating mode is Counter. */ 2256 (CLKPOL_POS << BF_CLKPOL) | /* Active high clock. */ 2257 /* ( CNTDIR_UP << BF_CLKPOL ) | // Count direction is Down. */ 2258 (CLKMULT_1X << BF_CLKMULT) | /* Clock multiplier is 1x. */ 2259 (CLKENAB_INDEX << BF_CLKENAB); 2260 /* uint16_t DisableIntSrc=TRUE; */ 2261 /* uint32_t Preloadvalue; //Counter initial value */ 2262 uint16_t valueSrclatch = LATCHSRC_AB_READ; 2263 uint16_t enab = CLKENAB_ALWAYS; 2264 enc_private *k = &encpriv[CR_CHAN(insn->chanspec)]; 2265 2266 DEBUG("s626_enc_insn_config: encoder config\n"); 2267 2268 /* (data==NULL) ? (Preloadvalue=0) : (Preloadvalue=data[0]); */ 2269 2270 k->SetMode(dev, k, Setup, TRUE); 2271 Preload(dev, k, *(insn->data)); 2272 k->PulseIndex(dev, k); 2273 SetLatchSource(dev, k, valueSrclatch); 2274 k->SetEnable(dev, k, (uint16_t) (enab != 0)); 2275 2276 return insn->n; 2277} 2278 2279static int s626_enc_insn_read(comedi_device * dev, comedi_subdevice * s, 2280 comedi_insn * insn, lsampl_t * data) 2281{ 2282 2283 int n; 2284 enc_private *k = &encpriv[CR_CHAN(insn->chanspec)]; 2285 2286 DEBUG("s626_enc_insn_read: encoder read channel %d \n", 2287 CR_CHAN(insn->chanspec)); 2288 2289 for (n = 0; n < insn->n; n++) 2290 data[n] = ReadLatch(dev, k); 2291 2292 DEBUG("s626_enc_insn_read: encoder sample %d\n", data[n]); 2293 2294 return n; 2295} 2296 2297static int s626_enc_insn_write(comedi_device * dev, comedi_subdevice * s, 2298 comedi_insn * insn, lsampl_t * data) 2299{ 2300 2301 enc_private *k = &encpriv[CR_CHAN(insn->chanspec)]; 2302 2303 DEBUG("s626_enc_insn_write: encoder write channel %d \n", 2304 CR_CHAN(insn->chanspec)); 2305 2306 /* Set the preload register */ 2307 Preload(dev, k, data[0]); 2308 2309 /* Software index pulse forces the preload register to load */ 2310 /* into the counter */ 2311 k->SetLoadTrig(dev, k, 0); 2312 k->PulseIndex(dev, k); 2313 k->SetLoadTrig(dev, k, 2); 2314 2315 DEBUG("s626_enc_insn_write: End encoder write\n"); 2316 2317 return 1; 2318} 2319 2320static void s626_timer_load(comedi_device * dev, enc_private * k, int tick) 2321{ 2322 uint16_t Setup = (LOADSRC_INDX << BF_LOADSRC) | /* Preload upon */ 2323 /* index. */ 2324 (INDXSRC_SOFT << BF_INDXSRC) | /* Disable hardware index. */ 2325 (CLKSRC_TIMER << BF_CLKSRC) | /* Operating mode is Timer. */ 2326 (CLKPOL_POS << BF_CLKPOL) | /* Active high clock. */ 2327 (CNTDIR_DOWN << BF_CLKPOL) | /* Count direction is Down. */ 2328 (CLKMULT_1X << BF_CLKMULT) | /* Clock multiplier is 1x. */ 2329 (CLKENAB_INDEX << BF_CLKENAB); 2330 uint16_t valueSrclatch = LATCHSRC_A_INDXA; 2331 /* uint16_t enab=CLKENAB_ALWAYS; */ 2332 2333 k->SetMode(dev, k, Setup, FALSE); 2334 2335 /* Set the preload register */ 2336 Preload(dev, k, tick); 2337 2338 /* Software index pulse forces the preload register to load */ 2339 /* into the counter */ 2340 k->SetLoadTrig(dev, k, 0); 2341 k->PulseIndex(dev, k); 2342 2343 /* set reload on counter overflow */ 2344 k->SetLoadTrig(dev, k, 1); 2345 2346 /* set interrupt on overflow */ 2347 k->SetIntSrc(dev, k, INTSRC_OVER); 2348 2349 SetLatchSource(dev, k, valueSrclatch); 2350 /* k->SetEnable(dev,k,(uint16_t)(enab != 0)); */ 2351} 2352 2353/* *********** DAC FUNCTIONS *********** */ 2354 2355/* Slot 0 base settings. */ 2356#define VECT0 ( XSD2 | RSD3 | SIB_A2 ) 2357/* Slot 0 always shifts in 0xFF and store it to FB_BUFFER2. */ 2358 2359/* TrimDac LogicalChan-to-PhysicalChan mapping table. */ 2360static uint8_t trimchan[] = { 10, 9, 8, 3, 2, 7, 6, 1, 0, 5, 4 }; 2361 2362/* TrimDac LogicalChan-to-EepromAdrs mapping table. */ 2363static uint8_t trimadrs[] = 2364 { 0x40, 0x41, 0x42, 0x50, 0x51, 0x52, 0x53, 0x60, 0x61, 0x62, 0x63 }; 2365 2366static void LoadTrimDACs(comedi_device * dev) 2367{ 2368 register uint8_t i; 2369 2370 /* Copy TrimDac setpoint values from EEPROM to TrimDacs. */ 2371 for (i = 0; i < (sizeof(trimchan) / sizeof(trimchan[0])); i++) 2372 WriteTrimDAC(dev, i, I2Cread(dev, trimadrs[i])); 2373} 2374 2375static void WriteTrimDAC(comedi_device * dev, uint8_t LogicalChan, 2376 uint8_t DacData) 2377{ 2378 uint32_t chan; 2379 2380 /* Save the new setpoint in case the application needs to read it back later. */ 2381 devpriv->TrimSetpoint[LogicalChan] = (uint8_t) DacData; 2382 2383 /* Map logical channel number to physical channel number. */ 2384 chan = (uint32_t) trimchan[LogicalChan]; 2385 2386 /* Set up TSL2 records for TrimDac write operation. All slots shift 2387 * 0xFF in from pulled-up SD3 so that the end of the slot sequence 2388 * can be detected. 2389 */ 2390 2391 SETVECT(2, XSD2 | XFIFO_1 | WS3); 2392 /* Slot 2: Send high uint8_t to target TrimDac. */ 2393 SETVECT(3, XSD2 | XFIFO_0 | WS3); 2394 /* Slot 3: Send low uint8_t to target TrimDac. */ 2395 SETVECT(4, XSD2 | XFIFO_3 | WS1); 2396 /* Slot 4: Send NOP high uint8_t to DAC0 to keep clock running. */ 2397 SETVECT(5, XSD2 | XFIFO_2 | WS1 | EOS); 2398 /* Slot 5: Send NOP low uint8_t to DAC0. */ 2399 2400 /* Construct and transmit target DAC's serial packet: 2401 * ( 0000 AAAA ), ( DDDD DDDD ),( 0x00 ),( 0x00 ) where A<3:0> is the 2402 * DAC channel's address, and D<7:0> is the DAC setpoint. Append a 2403 * WORD value (that writes a channel 0 NOP command to a non-existent 2404 * main DAC channel) that serves to keep the clock running after the 2405 * packet has been sent to the target DAC. 2406 */ 2407 2408 /* Address the DAC channel within the trimdac device. */ 2409 SendDAC(dev, ((uint32_t) chan << 8) 2410 | (uint32_t) DacData); /* Include DAC setpoint data. */ 2411} 2412 2413/* ************** EEPROM ACCESS FUNCTIONS ************** */ 2414/* Read uint8_t from EEPROM. */ 2415 2416static uint8_t I2Cread(comedi_device * dev, uint8_t addr) 2417{ 2418 uint8_t rtnval; 2419 2420 /* Send EEPROM target address. */ 2421 if (I2Chandshake(dev, I2C_B2(I2C_ATTRSTART, I2CW) 2422 /* Byte2 = I2C command: write to I2C EEPROM device. */ 2423 | I2C_B1(I2C_ATTRSTOP, addr) 2424 /* Byte1 = EEPROM internal target address. */ 2425 | I2C_B0(I2C_ATTRNOP, 0))) /* Byte0 = Not sent. */ 2426 { 2427 /* Abort function and declare error if handshake failed. */ 2428 DEBUG("I2Cread: error handshake I2Cread a\n"); 2429 return 0; 2430 } 2431 /* Execute EEPROM read. */ 2432 if (I2Chandshake(dev, I2C_B2(I2C_ATTRSTART, I2CR) /* Byte2 = I2C */ 2433 /* command: read */ 2434 /* from I2C EEPROM */ 2435 /* device. */ 2436 | I2C_B1(I2C_ATTRSTOP, 0) /* Byte1 receives */ 2437 /* uint8_t from */ 2438 /* EEPROM. */ 2439 | I2C_B0(I2C_ATTRNOP, 0))) /* Byte0 = Not */ 2440 /* sent. */ 2441 { 2442 /* Abort function and declare error if handshake failed. */ 2443 DEBUG("I2Cread: error handshake I2Cread b\n"); 2444 return 0; 2445 } 2446 /* Return copy of EEPROM value. */ 2447 rtnval = (uint8_t) (RR7146(P_I2CCTRL) >> 16); 2448 return rtnval; 2449} 2450 2451static uint32_t I2Chandshake(comedi_device * dev, uint32_t val) 2452{ 2453 /* Write I2C command to I2C Transfer Control shadow register. */ 2454 WR7146(P_I2CCTRL, val); 2455 2456 /* Upload I2C shadow registers into working registers and wait for */ 2457 /* upload confirmation. */ 2458 2459 MC_ENABLE(P_MC2, MC2_UPLD_IIC); 2460 while (!MC_TEST(P_MC2, MC2_UPLD_IIC)) ; 2461 2462 /* Wait until I2C bus transfer is finished or an error occurs. */ 2463 while ((RR7146(P_I2CCTRL) & (I2C_BUSY | I2C_ERR)) == I2C_BUSY) ; 2464 2465 /* Return non-zero if I2C error occured. */ 2466 return RR7146(P_I2CCTRL) & I2C_ERR; 2467 2468} 2469 2470/* Private helper function: Write setpoint to an application DAC channel. */ 2471 2472static void SetDAC(comedi_device * dev, uint16_t chan, short dacdata) 2473{ 2474 register uint16_t signmask; 2475 register uint32_t WSImage; 2476 2477 /* Adjust DAC data polarity and set up Polarity Control Register */ 2478 /* image. */ 2479 signmask = 1 << chan; 2480 if (dacdata < 0) { 2481 dacdata = -dacdata; 2482 devpriv->Dacpol |= signmask; 2483 } else 2484 devpriv->Dacpol &= ~signmask; 2485 2486 /* Limit DAC setpoint value to valid range. */ 2487 if ((uint16_t) dacdata > 0x1FFF) 2488 dacdata = 0x1FFF; 2489 2490 /* Set up TSL2 records (aka "vectors") for DAC update. Vectors V2 2491 * and V3 transmit the setpoint to the target DAC. V4 and V5 send 2492 * data to a non-existent TrimDac channel just to keep the clock 2493 * running after sending data to the target DAC. This is necessary 2494 * to eliminate the clock glitch that would otherwise occur at the 2495 * end of the target DAC's serial data stream. When the sequence 2496 * restarts at V0 (after executing V5), the gate array automatically 2497 * disables gating for the DAC clock and all DAC chip selects. 2498 */ 2499 2500 WSImage = (chan & 2) ? WS1 : WS2; 2501 /* Choose DAC chip select to be asserted. */ 2502 SETVECT(2, XSD2 | XFIFO_1 | WSImage); 2503 /* Slot 2: Transmit high data byte to target DAC. */ 2504 SETVECT(3, XSD2 | XFIFO_0 | WSImage); 2505 /* Slot 3: Transmit low data byte to target DAC. */ 2506 SETVECT(4, XSD2 | XFIFO_3 | WS3); 2507 /* Slot 4: Transmit to non-existent TrimDac channel to keep clock */ 2508 SETVECT(5, XSD2 | XFIFO_2 | WS3 | EOS); 2509 /* Slot 5: running after writing target DAC's low data byte. */ 2510 2511 /* Construct and transmit target DAC's serial packet: 2512 * ( A10D DDDD ),( DDDD DDDD ),( 0x0F ),( 0x00 ) where A is chan<0>, 2513 * and D<12:0> is the DAC setpoint. Append a WORD value (that writes 2514 * to a non-existent TrimDac channel) that serves to keep the clock 2515 * running after the packet has been sent to the target DAC. 2516 */ 2517 SendDAC(dev, 0x0F000000 2518 /* Continue clock after target DAC data (write to non-existent trimdac). */ 2519 | 0x00004000 2520 /* Address the two main dual-DAC devices (TSL's chip select enables 2521 * target device). */ 2522 | ((uint32_t) (chan & 1) << 15) 2523 /* Address the DAC channel within the device. */ 2524 | (uint32_t) dacdata); /* Include DAC setpoint data. */ 2525 2526} 2527 2528/* Private helper function: Transmit serial data to DAC via Audio 2529 * channel 2. Assumes: (1) TSL2 slot records initialized, and (2) 2530 * Dacpol contains valid target image. 2531 */ 2532 2533static void SendDAC(comedi_device * dev, uint32_t val) 2534{ 2535 2536 /* START THE SERIAL CLOCK RUNNING ------------- */ 2537 2538 /* Assert DAC polarity control and enable gating of DAC serial clock 2539 * and audio bit stream signals. At this point in time we must be 2540 * assured of being in time slot 0. If we are not in slot 0, the 2541 * serial clock and audio stream signals will be disabled; this is 2542 * because the following DEBIwrite statement (which enables signals 2543 * to be passed through the gate array) would execute before the 2544 * trailing edge of WS1/WS3 (which turns off the signals), thus 2545 * causing the signals to be inactive during the DAC write. 2546 */ 2547 DEBIwrite(dev, LP_DACPOL, devpriv->Dacpol); 2548 2549 /* TRANSFER OUTPUT DWORD VALUE INTO A2'S OUTPUT FIFO ---------------- */ 2550 2551 /* Copy DAC setpoint value to DAC's output DMA buffer. */ 2552 2553 /* WR7146( (uint32_t)devpriv->pDacWBuf, val ); */ 2554 *devpriv->pDacWBuf = val; 2555 2556 /* enab the output DMA transfer. This will cause the DMAC to copy 2557 * the DAC's data value to A2's output FIFO. The DMA transfer will 2558 * then immediately terminate because the protection address is 2559 * reached upon transfer of the first DWORD value. 2560 */ 2561 MC_ENABLE(P_MC1, MC1_A2OUT); 2562 2563 /* While the DMA transfer is executing ... */ 2564 2565 /* Reset Audio2 output FIFO's underflow flag (along with any other 2566 * FIFO underflow/overflow flags). When set, this flag will 2567 * indicate that we have emerged from slot 0. 2568 */ 2569 WR7146(P_ISR, ISR_AFOU); 2570 2571 /* Wait for the DMA transfer to finish so that there will be data 2572 * available in the FIFO when time slot 1 tries to transfer a DWORD 2573 * from the FIFO to the output buffer register. We test for DMA 2574 * Done by polling the DMAC enable flag; this flag is automatically 2575 * cleared when the transfer has finished. 2576 */ 2577 while ((RR7146(P_MC1) & MC1_A2OUT) != 0) ; 2578 2579 /* START THE OUTPUT STREAM TO THE TARGET DAC -------------------- */ 2580 2581 /* FIFO data is now available, so we enable execution of time slots 2582 * 1 and higher by clearing the EOS flag in slot 0. Note that SD3 2583 * will be shifted in and stored in FB_BUFFER2 for end-of-slot-list 2584 * detection. 2585 */ 2586 SETVECT(0, XSD2 | RSD3 | SIB_A2); 2587 2588 /* Wait for slot 1 to execute to ensure that the Packet will be 2589 * transmitted. This is detected by polling the Audio2 output FIFO 2590 * underflow flag, which will be set when slot 1 execution has 2591 * finished transferring the DAC's data DWORD from the output FIFO 2592 * to the output buffer register. 2593 */ 2594 while ((RR7146(P_SSR) & SSR_AF2_OUT) == 0) ; 2595 2596 /* Set up to trap execution at slot 0 when the TSL sequencer cycles 2597 * back to slot 0 after executing the EOS in slot 5. Also, 2598 * simultaneously shift out and in the 0x00 that is ALWAYS the value 2599 * stored in the last byte to be shifted out of the FIFO's DWORD 2600 * buffer register. 2601 */ 2602 SETVECT(0, XSD2 | XFIFO_2 | RSD2 | SIB_A2 | EOS); 2603 2604 /* WAIT FOR THE TRANSACTION TO FINISH ----------------------- */ 2605 2606 /* Wait for the TSL to finish executing all time slots before 2607 * exiting this function. We must do this so that the next DAC 2608 * write doesn't start, thereby enabling clock/chip select signals: 2609 * 2610 * 1. Before the TSL sequence cycles back to slot 0, which disables 2611 * the clock/cs signal gating and traps slot // list execution. 2612 * we have not yet finished slot 5 then the clock/cs signals are 2613 * still gated and we have not finished transmitting the stream. 2614 * 2615 * 2. While slots 2-5 are executing due to a late slot 0 trap. In 2616 * this case, the slot sequence is currently repeating, but with 2617 * clock/cs signals disabled. We must wait for slot 0 to trap 2618 * execution before setting up the next DAC setpoint DMA transfer 2619 * and enabling the clock/cs signals. To detect the end of slot 5, 2620 * we test for the FB_BUFFER2 MSB contents to be equal to 0xFF. If 2621 * the TSL has not yet finished executing slot 5 ... 2622 */ 2623 if ((RR7146(P_FB_BUFFER2) & 0xFF000000) != 0) { 2624 /* The trap was set on time and we are still executing somewhere 2625 * in slots 2-5, so we now wait for slot 0 to execute and trap 2626 * TSL execution. This is detected when FB_BUFFER2 MSB changes 2627 * from 0xFF to 0x00, which slot 0 causes to happen by shifting 2628 * out/in on SD2 the 0x00 that is always referenced by slot 5. 2629 */ 2630 while ((RR7146(P_FB_BUFFER2) & 0xFF000000) != 0) ; 2631 } 2632 /* Either (1) we were too late setting the slot 0 trap; the TSL 2633 * sequencer restarted slot 0 before we could set the EOS trap flag, 2634 * or (2) we were not late and execution is now trapped at slot 0. 2635 * In either case, we must now change slot 0 so that it will store 2636 * value 0xFF (instead of 0x00) to FB_BUFFER2 next time it executes. 2637 * In order to do this, we reprogram slot 0 so that it will shift in 2638 * SD3, which is driven only by a pull-up resistor. 2639 */ 2640 SETVECT(0, RSD3 | SIB_A2 | EOS); 2641 2642 /* Wait for slot 0 to execute, at which time the TSL is setup for 2643 * the next DAC write. This is detected when FB_BUFFER2 MSB changes 2644 * from 0x00 to 0xFF. 2645 */ 2646 while ((RR7146(P_FB_BUFFER2) & 0xFF000000) == 0) ; 2647} 2648 2649static void WriteMISC2(comedi_device * dev, uint16_t NewImage) 2650{ 2651 DEBIwrite(dev, LP_MISC1, MISC1_WENABLE); /* enab writes to */ 2652 /* MISC2 register. */ 2653 DEBIwrite(dev, LP_WRMISC2, NewImage); /* Write new image to MISC2. */ 2654 DEBIwrite(dev, LP_MISC1, MISC1_WDISABLE); /* Disable writes to MISC2. */ 2655} 2656 2657/* Initialize the DEBI interface for all transfers. */ 2658 2659static uint16_t DEBIread(comedi_device * dev, uint16_t addr) 2660{ 2661 uint16_t retval; 2662 2663 /* Set up DEBI control register value in shadow RAM. */ 2664 WR7146(P_DEBICMD, DEBI_CMD_RDWORD | addr); 2665 2666 /* Execute the DEBI transfer. */ 2667 DEBItransfer(dev); 2668 2669 /* Fetch target register value. */ 2670 retval = (uint16_t) RR7146(P_DEBIAD); 2671 2672 /* Return register value. */ 2673 return retval; 2674} 2675 2676/* Execute a DEBI transfer. This must be called from within a */ 2677/* critical section. */ 2678static void DEBItransfer(comedi_device * dev) 2679{ 2680 /* Initiate upload of shadow RAM to DEBI control register. */ 2681 MC_ENABLE(P_MC2, MC2_UPLD_DEBI); 2682 2683 /* Wait for completion of upload from shadow RAM to DEBI control */ 2684 /* register. */ 2685 while (!MC_TEST(P_MC2, MC2_UPLD_DEBI)) ; 2686 2687 /* Wait until DEBI transfer is done. */ 2688 while (RR7146(P_PSR) & PSR_DEBI_S) ; 2689} 2690 2691/* Write a value to a gate array register. */ 2692static void DEBIwrite(comedi_device * dev, uint16_t addr, uint16_t wdata) 2693{ 2694 2695 /* Set up DEBI control register value in shadow RAM. */ 2696 WR7146(P_DEBICMD, DEBI_CMD_WRWORD | addr); 2697 WR7146(P_DEBIAD, wdata); 2698 2699 /* Execute the DEBI transfer. */ 2700 DEBItransfer(dev); 2701} 2702 2703/* Replace the specified bits in a gate array register. Imports: mask 2704 * specifies bits that are to be preserved, wdata is new value to be 2705 * or'd with the masked original. 2706 */ 2707static void DEBIreplace(comedi_device * dev, uint16_t addr, uint16_t mask, 2708 uint16_t wdata) 2709{ 2710 2711 /* Copy target gate array register into P_DEBIAD register. */ 2712 WR7146(P_DEBICMD, DEBI_CMD_RDWORD | addr); 2713 /* Set up DEBI control reg value in shadow RAM. */ 2714 DEBItransfer(dev); /* Execute the DEBI Read transfer. */ 2715 2716 /* Write back the modified image. */ 2717 WR7146(P_DEBICMD, DEBI_CMD_WRWORD | addr); 2718 /* Set up DEBI control reg value in shadow RAM. */ 2719 2720 WR7146(P_DEBIAD, wdata | ((uint16_t) RR7146(P_DEBIAD) & mask)); 2721 /* Modify the register image. */ 2722 DEBItransfer(dev); /* Execute the DEBI Write transfer. */ 2723} 2724 2725static void CloseDMAB(comedi_device * dev, DMABUF * pdma, size_t bsize) 2726{ 2727 void *vbptr; 2728 dma_addr_t vpptr; 2729 2730 DEBUG("CloseDMAB: Entering S626DRV_CloseDMAB():\n"); 2731 if (pdma == NULL) 2732 return; 2733 /* find the matching allocation from the board struct */ 2734 2735 vbptr = pdma->LogicalBase; 2736 vpptr = pdma->PhysicalBase; 2737 if (vbptr) { 2738 pci_free_consistent(devpriv->pdev, bsize, vbptr, vpptr); 2739 pdma->LogicalBase = 0; 2740 pdma->PhysicalBase = 0; 2741 2742 DEBUG("CloseDMAB(): Logical=%p, bsize=%d, Physical=0x%x\n", 2743 vbptr, bsize, (uint32_t) vpptr); 2744 } 2745} 2746 2747/* ****** COUNTER FUNCTIONS ******* */ 2748/* All counter functions address a specific counter by means of the 2749 * "Counter" argument, which is a logical counter number. The Counter 2750 * argument may have any of the following legal values: 0=0A, 1=1A, 2751 * 2=2A, 3=0B, 4=1B, 5=2B. 2752 */ 2753 2754/* Forward declarations for functions that are common to both A and B counters: */ 2755 2756/* ****** PRIVATE COUNTER FUNCTIONS ****** */ 2757 2758/* Read a counter's output latch. */ 2759 2760static uint32_t ReadLatch(comedi_device * dev, enc_private * k) 2761{ 2762 register uint32_t value; 2763 /* DEBUG FIXME DEBUG("ReadLatch: Read Latch enter\n"); */ 2764 2765 /* Latch counts and fetch LSW of latched counts value. */ 2766 value = (uint32_t) DEBIread(dev, k->MyLatchLsw); 2767 2768 /* Fetch MSW of latched counts and combine with LSW. */ 2769 value |= ((uint32_t) DEBIread(dev, k->MyLatchLsw + 2) << 16); 2770 2771 /* DEBUG FIXME DEBUG("ReadLatch: Read Latch exit\n"); */ 2772 2773 /* Return latched counts. */ 2774 return value; 2775} 2776 2777/* Reset a counter's index and overflow event capture flags. */ 2778 2779static void ResetCapFlags_A(comedi_device * dev, enc_private * k) 2780{ 2781 DEBIreplace(dev, k->MyCRB, (uint16_t) (~CRBMSK_INTCTRL), 2782 CRBMSK_INTRESETCMD | CRBMSK_INTRESET_A); 2783} 2784 2785static void ResetCapFlags_B(comedi_device * dev, enc_private * k) 2786{ 2787 DEBIreplace(dev, k->MyCRB, (uint16_t) (~CRBMSK_INTCTRL), 2788 CRBMSK_INTRESETCMD | CRBMSK_INTRESET_B); 2789} 2790 2791/* Return counter setup in a format (COUNTER_SETUP) that is consistent */ 2792/* for both A and B counters. */ 2793 2794static uint16_t GetMode_A(comedi_device * dev, enc_private * k) 2795{ 2796 register uint16_t cra; 2797 register uint16_t crb; 2798 register uint16_t setup; 2799 2800 /* Fetch CRA and CRB register images. */ 2801 cra = DEBIread(dev, k->MyCRA); 2802 crb = DEBIread(dev, k->MyCRB); 2803 2804 /* Populate the standardized counter setup bit fields. Note: */ 2805 /* IndexSrc is restricted to ENC_X or IndxPol. */ 2806 setup = ((cra & STDMSK_LOADSRC) /* LoadSrc = LoadSrcA. */ 2807 | ((crb << (STDBIT_LATCHSRC - CRBBIT_LATCHSRC)) & STDMSK_LATCHSRC) /* LatchSrc = LatchSrcA. */ 2808 | ((cra << (STDBIT_INTSRC - CRABIT_INTSRC_A)) & STDMSK_INTSRC) /* IntSrc = IntSrcA. */ 2809 | ((cra << (STDBIT_INDXSRC - (CRABIT_INDXSRC_A + 1))) & STDMSK_INDXSRC) /* IndxSrc = IndxSrcA<1>. */ 2810 | ((cra >> (CRABIT_INDXPOL_A - STDBIT_INDXPOL)) & STDMSK_INDXPOL) /* IndxPol = IndxPolA. */ 2811 | ((crb >> (CRBBIT_CLKENAB_A - STDBIT_CLKENAB)) & STDMSK_CLKENAB)); /* ClkEnab = ClkEnabA. */ 2812 2813 /* Adjust mode-dependent parameters. */ 2814 if (cra & (2 << CRABIT_CLKSRC_A)) /* If Timer mode (ClkSrcA<1> == 1): */ 2815 setup |= ((CLKSRC_TIMER << STDBIT_CLKSRC) /* Indicate Timer mode. */ 2816 | ((cra << (STDBIT_CLKPOL - CRABIT_CLKSRC_A)) & STDMSK_CLKPOL) /* Set ClkPol to indicate count direction (ClkSrcA<0>). */ 2817 | (MULT_X1 << STDBIT_CLKMULT)); /* ClkMult must be 1x in Timer mode. */ 2818 2819 else /* If Counter mode (ClkSrcA<1> == 0): */ 2820 setup |= ((CLKSRC_COUNTER << STDBIT_CLKSRC) /* Indicate Counter mode. */ 2821 | ((cra >> (CRABIT_CLKPOL_A - STDBIT_CLKPOL)) & STDMSK_CLKPOL) /* Pass through ClkPol. */ 2822 | (((cra & CRAMSK_CLKMULT_A) == (MULT_X0 << CRABIT_CLKMULT_A)) ? /* Force ClkMult to 1x if not legal, else pass through. */ 2823 (MULT_X1 << STDBIT_CLKMULT) : 2824 ((cra >> (CRABIT_CLKMULT_A - 2825 STDBIT_CLKMULT)) & 2826 STDMSK_CLKMULT))); 2827 2828 /* Return adjusted counter setup. */ 2829 return setup; 2830} 2831 2832static uint16_t GetMode_B(comedi_device * dev, enc_private * k) 2833{ 2834 register uint16_t cra; 2835 register uint16_t crb; 2836 register uint16_t setup; 2837 2838 /* Fetch CRA and CRB register images. */ 2839 cra = DEBIread(dev, k->MyCRA); 2840 crb = DEBIread(dev, k->MyCRB); 2841 2842 /* Populate the standardized counter setup bit fields. Note: */ 2843 /* IndexSrc is restricted to ENC_X or IndxPol. */ 2844 setup = (((crb << (STDBIT_INTSRC - CRBBIT_INTSRC_B)) & STDMSK_INTSRC) /* IntSrc = IntSrcB. */ 2845 | ((crb << (STDBIT_LATCHSRC - CRBBIT_LATCHSRC)) & STDMSK_LATCHSRC) /* LatchSrc = LatchSrcB. */ 2846 | ((crb << (STDBIT_LOADSRC - CRBBIT_LOADSRC_B)) & STDMSK_LOADSRC) /* LoadSrc = LoadSrcB. */ 2847 | ((crb << (STDBIT_INDXPOL - CRBBIT_INDXPOL_B)) & STDMSK_INDXPOL) /* IndxPol = IndxPolB. */ 2848 | ((crb >> (CRBBIT_CLKENAB_B - STDBIT_CLKENAB)) & STDMSK_CLKENAB) /* ClkEnab = ClkEnabB. */ 2849 | ((cra >> ((CRABIT_INDXSRC_B + 1) - STDBIT_INDXSRC)) & STDMSK_INDXSRC)); /* IndxSrc = IndxSrcB<1>. */ 2850 2851 /* Adjust mode-dependent parameters. */ 2852 if ((crb & CRBMSK_CLKMULT_B) == (MULT_X0 << CRBBIT_CLKMULT_B)) /* If Extender mode (ClkMultB == MULT_X0): */ 2853 setup |= ((CLKSRC_EXTENDER << STDBIT_CLKSRC) /* Indicate Extender mode. */ 2854 | (MULT_X1 << STDBIT_CLKMULT) /* Indicate multiplier is 1x. */ 2855 | ((cra >> (CRABIT_CLKSRC_B - STDBIT_CLKPOL)) & STDMSK_CLKPOL)); /* Set ClkPol equal to Timer count direction (ClkSrcB<0>). */ 2856 2857 else if (cra & (2 << CRABIT_CLKSRC_B)) /* If Timer mode (ClkSrcB<1> == 1): */ 2858 setup |= ((CLKSRC_TIMER << STDBIT_CLKSRC) /* Indicate Timer mode. */ 2859 | (MULT_X1 << STDBIT_CLKMULT) /* Indicate multiplier is 1x. */ 2860 | ((cra >> (CRABIT_CLKSRC_B - STDBIT_CLKPOL)) & STDMSK_CLKPOL)); /* Set ClkPol equal to Timer count direction (ClkSrcB<0>). */ 2861 2862 else /* If Counter mode (ClkSrcB<1> == 0): */ 2863 setup |= ((CLKSRC_COUNTER << STDBIT_CLKSRC) /* Indicate Timer mode. */ 2864 | ((crb >> (CRBBIT_CLKMULT_B - STDBIT_CLKMULT)) & STDMSK_CLKMULT) /* Clock multiplier is passed through. */ 2865 | ((crb << (STDBIT_CLKPOL - CRBBIT_CLKPOL_B)) & STDMSK_CLKPOL)); /* Clock polarity is passed through. */ 2866 2867 /* Return adjusted counter setup. */ 2868 return setup; 2869} 2870 2871/* 2872 * Set the operating mode for the specified counter. The setup 2873 * parameter is treated as a COUNTER_SETUP data type. The following 2874 * parameters are programmable (all other parms are ignored): ClkMult, 2875 * ClkPol, ClkEnab, IndexSrc, IndexPol, LoadSrc. 2876 */ 2877 2878static void SetMode_A(comedi_device * dev, enc_private * k, uint16_t Setup, 2879 uint16_t DisableIntSrc) 2880{ 2881 register uint16_t cra; 2882 register uint16_t crb; 2883 register uint16_t setup = Setup; /* Cache the Standard Setup. */ 2884 2885 /* Initialize CRA and CRB images. */ 2886 cra = ((setup & CRAMSK_LOADSRC_A) /* Preload trigger is passed through. */ 2887 | ((setup & STDMSK_INDXSRC) >> (STDBIT_INDXSRC - (CRABIT_INDXSRC_A + 1)))); /* IndexSrc is restricted to ENC_X or IndxPol. */ 2888 2889 crb = (CRBMSK_INTRESETCMD | CRBMSK_INTRESET_A /* Reset any pending CounterA event captures. */ 2890 | ((setup & STDMSK_CLKENAB) << (CRBBIT_CLKENAB_A - STDBIT_CLKENAB))); /* Clock enable is passed through. */ 2891 2892 /* Force IntSrc to Disabled if DisableIntSrc is asserted. */ 2893 if (!DisableIntSrc) 2894 cra |= ((setup & STDMSK_INTSRC) >> (STDBIT_INTSRC - 2895 CRABIT_INTSRC_A)); 2896 2897 /* Populate all mode-dependent attributes of CRA & CRB images. */ 2898 switch ((setup & STDMSK_CLKSRC) >> STDBIT_CLKSRC) { 2899 case CLKSRC_EXTENDER: /* Extender Mode: Force to Timer mode */ 2900 /* (Extender valid only for B counters). */ 2901 2902 case CLKSRC_TIMER: /* Timer Mode: */ 2903 cra |= ((2 << CRABIT_CLKSRC_A) /* ClkSrcA<1> selects system clock */ 2904 | ((setup & STDMSK_CLKPOL) >> (STDBIT_CLKPOL - CRABIT_CLKSRC_A)) /* with count direction (ClkSrcA<0>) obtained from ClkPol. */ 2905 | (1 << CRABIT_CLKPOL_A) /* ClkPolA behaves as always-on clock enable. */ 2906 | (MULT_X1 << CRABIT_CLKMULT_A)); /* ClkMult must be 1x. */ 2907 break; 2908 2909 default: /* Counter Mode: */ 2910 cra |= (CLKSRC_COUNTER /* Select ENC_C and ENC_D as clock/direction inputs. */ 2911 | ((setup & STDMSK_CLKPOL) << (CRABIT_CLKPOL_A - STDBIT_CLKPOL)) /* Clock polarity is passed through. */ 2912 | (((setup & STDMSK_CLKMULT) == (MULT_X0 << STDBIT_CLKMULT)) ? /* Force multiplier to x1 if not legal, otherwise pass through. */ 2913 (MULT_X1 << CRABIT_CLKMULT_A) : 2914 ((setup & STDMSK_CLKMULT) << (CRABIT_CLKMULT_A - 2915 STDBIT_CLKMULT)))); 2916 } 2917 2918 /* Force positive index polarity if IndxSrc is software-driven only, */ 2919 /* otherwise pass it through. */ 2920 if (~setup & STDMSK_INDXSRC) 2921 cra |= ((setup & STDMSK_INDXPOL) << (CRABIT_INDXPOL_A - 2922 STDBIT_INDXPOL)); 2923 2924 /* If IntSrc has been forced to Disabled, update the MISC2 interrupt */ 2925 /* enable mask to indicate the counter interrupt is disabled. */ 2926 if (DisableIntSrc) 2927 devpriv->CounterIntEnabs &= ~k->MyEventBits[3]; 2928 2929 /* While retaining CounterB and LatchSrc configurations, program the */ 2930 /* new counter operating mode. */ 2931 DEBIreplace(dev, k->MyCRA, CRAMSK_INDXSRC_B | CRAMSK_CLKSRC_B, cra); 2932 DEBIreplace(dev, k->MyCRB, 2933 (uint16_t) (~(CRBMSK_INTCTRL | CRBMSK_CLKENAB_A)), crb); 2934} 2935 2936static void SetMode_B(comedi_device * dev, enc_private * k, uint16_t Setup, 2937 uint16_t DisableIntSrc) 2938{ 2939 register uint16_t cra; 2940 register uint16_t crb; 2941 register uint16_t setup = Setup; /* Cache the Standard Setup. */ 2942 2943 /* Initialize CRA and CRB images. */ 2944 cra = ((setup & STDMSK_INDXSRC) << ((CRABIT_INDXSRC_B + 1) - STDBIT_INDXSRC)); /* IndexSrc field is restricted to ENC_X or IndxPol. */ 2945 2946 crb = (CRBMSK_INTRESETCMD | CRBMSK_INTRESET_B /* Reset event captures and disable interrupts. */ 2947 | ((setup & STDMSK_CLKENAB) << (CRBBIT_CLKENAB_B - STDBIT_CLKENAB)) /* Clock enable is passed through. */ 2948 | ((setup & STDMSK_LOADSRC) >> (STDBIT_LOADSRC - CRBBIT_LOADSRC_B))); /* Preload trigger source is passed through. */ 2949 2950 /* Force IntSrc to Disabled if DisableIntSrc is asserted. */ 2951 if (!DisableIntSrc) 2952 crb |= ((setup & STDMSK_INTSRC) >> (STDBIT_INTSRC - 2953 CRBBIT_INTSRC_B)); 2954 2955 /* Populate all mode-dependent attributes of CRA & CRB images. */ 2956 switch ((setup & STDMSK_CLKSRC) >> STDBIT_CLKSRC) { 2957 case CLKSRC_TIMER: /* Timer Mode: */ 2958 cra |= ((2 << CRABIT_CLKSRC_B) /* ClkSrcB<1> selects system clock */ 2959 | ((setup & STDMSK_CLKPOL) << (CRABIT_CLKSRC_B - STDBIT_CLKPOL))); /* with direction (ClkSrcB<0>) obtained from ClkPol. */ 2960 crb |= ((1 << CRBBIT_CLKPOL_B) /* ClkPolB behaves as always-on clock enable. */ 2961 | (MULT_X1 << CRBBIT_CLKMULT_B)); /* ClkMultB must be 1x. */ 2962 break; 2963 2964 case CLKSRC_EXTENDER: /* Extender Mode: */ 2965 cra |= ((2 << CRABIT_CLKSRC_B) /* ClkSrcB source is OverflowA (same as "timer") */ 2966 | ((setup & STDMSK_CLKPOL) << (CRABIT_CLKSRC_B - STDBIT_CLKPOL))); /* with direction obtained from ClkPol. */ 2967 crb |= ((1 << CRBBIT_CLKPOL_B) /* ClkPolB controls IndexB -- always set to active. */ 2968 | (MULT_X0 << CRBBIT_CLKMULT_B)); /* ClkMultB selects OverflowA as the clock source. */ 2969 break; 2970 2971 default: /* Counter Mode: */ 2972 cra |= (CLKSRC_COUNTER << CRABIT_CLKSRC_B); /* Select ENC_C and ENC_D as clock/direction inputs. */ 2973 crb |= (((setup & STDMSK_CLKPOL) >> (STDBIT_CLKPOL - CRBBIT_CLKPOL_B)) /* ClkPol is passed through. */ 2974 | (((setup & STDMSK_CLKMULT) == (MULT_X0 << STDBIT_CLKMULT)) ? /* Force ClkMult to x1 if not legal, otherwise pass through. */ 2975 (MULT_X1 << CRBBIT_CLKMULT_B) : 2976 ((setup & STDMSK_CLKMULT) << (CRBBIT_CLKMULT_B - 2977 STDBIT_CLKMULT)))); 2978 } 2979 2980 /* Force positive index polarity if IndxSrc is software-driven only, */ 2981 /* otherwise pass it through. */ 2982 if (~setup & STDMSK_INDXSRC) 2983 crb |= ((setup & STDMSK_INDXPOL) >> (STDBIT_INDXPOL - 2984 CRBBIT_INDXPOL_B)); 2985 2986 /* If IntSrc has been forced to Disabled, update the MISC2 interrupt */ 2987 /* enable mask to indicate the counter interrupt is disabled. */ 2988 if (DisableIntSrc) 2989 devpriv->CounterIntEnabs &= ~k->MyEventBits[3]; 2990 2991 /* While retaining CounterA and LatchSrc configurations, program the */ 2992 /* new counter operating mode. */ 2993 DEBIreplace(dev, k->MyCRA, 2994 (uint16_t) (~(CRAMSK_INDXSRC_B | CRAMSK_CLKSRC_B)), cra); 2995 DEBIreplace(dev, k->MyCRB, CRBMSK_CLKENAB_A | CRBMSK_LATCHSRC, crb); 2996} 2997 2998/* Return/set a counter's enable. enab: 0=always enabled, 1=enabled by index. */ 2999 3000static void SetEnable_A(comedi_device * dev, enc_private * k, uint16_t enab) 3001{ 3002 DEBUG("SetEnable_A: SetEnable_A enter 3541\n"); 3003 DEBIreplace(dev, k->MyCRB, 3004 (uint16_t) (~(CRBMSK_INTCTRL | CRBMSK_CLKENAB_A)), 3005 (uint16_t) (enab << CRBBIT_CLKENAB_A)); 3006} 3007 3008static void SetEnable_B(comedi_device * dev, enc_private * k, uint16_t enab) 3009{ 3010 DEBIreplace(dev, k->MyCRB, 3011 (uint16_t) (~(CRBMSK_INTCTRL | CRBMSK_CLKENAB_B)), 3012 (uint16_t) (enab << CRBBIT_CLKENAB_B)); 3013} 3014 3015static uint16_t GetEnable_A(comedi_device * dev, enc_private * k) 3016{ 3017 return (DEBIread(dev, k->MyCRB) >> CRBBIT_CLKENAB_A) & 1; 3018} 3019 3020static uint16_t GetEnable_B(comedi_device * dev, enc_private * k) 3021{ 3022 return (DEBIread(dev, k->MyCRB) >> CRBBIT_CLKENAB_B) & 1; 3023} 3024 3025/* Return/set a counter pair's latch trigger source. 0: On read 3026 * access, 1: A index latches A, 2: B index latches B, 3: A overflow 3027 * latches B. 3028 */ 3029 3030static void SetLatchSource(comedi_device * dev, enc_private * k, uint16_t value) 3031{ 3032 DEBUG("SetLatchSource: SetLatchSource enter 3550 \n"); 3033 DEBIreplace(dev, k->MyCRB, 3034 (uint16_t) (~(CRBMSK_INTCTRL | CRBMSK_LATCHSRC)), 3035 (uint16_t) (value << CRBBIT_LATCHSRC)); 3036 3037 DEBUG("SetLatchSource: SetLatchSource exit \n"); 3038} 3039 3040/* 3041 * static uint16_t GetLatchSource(comedi_device *dev, enc_private *k ) 3042 * { 3043 * return ( DEBIread( dev, k->MyCRB) >> CRBBIT_LATCHSRC ) & 3; 3044 * } 3045 */ 3046 3047/* 3048 * Return/set the event that will trigger transfer of the preload 3049 * register into the counter. 0=ThisCntr_Index, 1=ThisCntr_Overflow, 3050 * 2=OverflowA (B counters only), 3=disabled. 3051 */ 3052 3053static void SetLoadTrig_A(comedi_device * dev, enc_private * k, uint16_t Trig) 3054{ 3055 DEBIreplace(dev, k->MyCRA, (uint16_t) (~CRAMSK_LOADSRC_A), 3056 (uint16_t) (Trig << CRABIT_LOADSRC_A)); 3057} 3058 3059static void SetLoadTrig_B(comedi_device * dev, enc_private * k, uint16_t Trig) 3060{ 3061 DEBIreplace(dev, k->MyCRB, 3062 (uint16_t) (~(CRBMSK_LOADSRC_B | CRBMSK_INTCTRL)), 3063 (uint16_t) (Trig << CRBBIT_LOADSRC_B)); 3064} 3065 3066static uint16_t GetLoadTrig_A(comedi_device * dev, enc_private * k) 3067{ 3068 return (DEBIread(dev, k->MyCRA) >> CRABIT_LOADSRC_A) & 3; 3069} 3070 3071static uint16_t GetLoadTrig_B(comedi_device * dev, enc_private * k) 3072{ 3073 return (DEBIread(dev, k->MyCRB) >> CRBBIT_LOADSRC_B) & 3; 3074} 3075 3076/* Return/set counter interrupt source and clear any captured 3077 * index/overflow events. IntSource: 0=Disabled, 1=OverflowOnly, 3078 * 2=IndexOnly, 3=IndexAndOverflow. 3079 */ 3080 3081static void SetIntSrc_A(comedi_device * dev, enc_private * k, 3082 uint16_t IntSource) 3083{ 3084 /* Reset any pending counter overflow or index captures. */ 3085 DEBIreplace(dev, k->MyCRB, (uint16_t) (~CRBMSK_INTCTRL), 3086 CRBMSK_INTRESETCMD | CRBMSK_INTRESET_A); 3087 3088 /* Program counter interrupt source. */ 3089 DEBIreplace(dev, k->MyCRA, ~CRAMSK_INTSRC_A, 3090 (uint16_t) (IntSource << CRABIT_INTSRC_A)); 3091 3092 /* Update MISC2 interrupt enable mask. */ 3093 devpriv->CounterIntEnabs = 3094 (devpriv->CounterIntEnabs & ~k->MyEventBits[3]) | k-> 3095 MyEventBits[IntSource]; 3096} 3097 3098static void SetIntSrc_B(comedi_device * dev, enc_private * k, 3099 uint16_t IntSource) 3100{ 3101 uint16_t crb; 3102 3103 /* Cache writeable CRB register image. */ 3104 crb = DEBIread(dev, k->MyCRB) & ~CRBMSK_INTCTRL; 3105 3106 /* Reset any pending counter overflow or index captures. */ 3107 DEBIwrite(dev, k->MyCRB, 3108 (uint16_t) (crb | CRBMSK_INTRESETCMD | CRBMSK_INTRESET_B)); 3109 3110 /* Program counter interrupt source. */ 3111 DEBIwrite(dev, k->MyCRB, 3112 (uint16_t) ((crb & ~CRBMSK_INTSRC_B) | (IntSource << 3113 CRBBIT_INTSRC_B))); 3114 3115 /* Update MISC2 interrupt enable mask. */ 3116 devpriv->CounterIntEnabs = 3117 (devpriv->CounterIntEnabs & ~k->MyEventBits[3]) | k-> 3118 MyEventBits[IntSource]; 3119} 3120 3121static uint16_t GetIntSrc_A(comedi_device * dev, enc_private * k) 3122{ 3123 return (DEBIread(dev, k->MyCRA) >> CRABIT_INTSRC_A) & 3; 3124} 3125 3126static uint16_t GetIntSrc_B(comedi_device * dev, enc_private * k) 3127{ 3128 return (DEBIread(dev, k->MyCRB) >> CRBBIT_INTSRC_B) & 3; 3129} 3130 3131/* Return/set the clock multiplier. */ 3132 3133/* static void SetClkMult(comedi_device *dev, enc_private *k, uint16_t value ) */ 3134/* { */ 3135/* k->SetMode(dev, k, (uint16_t)( ( k->GetMode(dev, k ) & ~STDMSK_CLKMULT ) | ( value << STDBIT_CLKMULT ) ), FALSE ); */ 3136/* } */ 3137 3138/* static uint16_t GetClkMult(comedi_device *dev, enc_private *k ) */ 3139/* { */ 3140/* return ( k->GetMode(dev, k ) >> STDBIT_CLKMULT ) & 3; */ 3141/* } */ 3142 3143/* Return/set the clock polarity. */ 3144 3145/* static void SetClkPol( comedi_device *dev,enc_private *k, uint16_t value ) */ 3146/* { */ 3147/* k->SetMode(dev, k, (uint16_t)( ( k->GetMode(dev, k ) & ~STDMSK_CLKPOL ) | ( value << STDBIT_CLKPOL ) ), FALSE ); */ 3148/* } */ 3149 3150/* static uint16_t GetClkPol(comedi_device *dev, enc_private *k ) */ 3151/* { */ 3152/* return ( k->GetMode(dev, k ) >> STDBIT_CLKPOL ) & 1; */ 3153/* } */ 3154 3155/* Return/set the clock source. */ 3156 3157/* static void SetClkSrc( comedi_device *dev,enc_private *k, uint16_t value ) */ 3158/* { */ 3159/* k->SetMode(dev, k, (uint16_t)( ( k->GetMode(dev, k ) & ~STDMSK_CLKSRC ) | ( value << STDBIT_CLKSRC ) ), FALSE ); */ 3160/* } */ 3161 3162/* static uint16_t GetClkSrc( comedi_device *dev,enc_private *k ) */ 3163/* { */ 3164/* return ( k->GetMode(dev, k ) >> STDBIT_CLKSRC ) & 3; */ 3165/* } */ 3166 3167/* Return/set the index polarity. */ 3168 3169/* static void SetIndexPol(comedi_device *dev, enc_private *k, uint16_t value ) */ 3170/* { */ 3171/* k->SetMode(dev, k, (uint16_t)( ( k->GetMode(dev, k ) & ~STDMSK_INDXPOL ) | ( (value != 0) << STDBIT_INDXPOL ) ), FALSE ); */ 3172/* } */ 3173 3174/* static uint16_t GetIndexPol(comedi_device *dev, enc_private *k ) */ 3175/* { */ 3176/* return ( k->GetMode(dev, k ) >> STDBIT_INDXPOL ) & 1; */ 3177/* } */ 3178 3179/* Return/set the index source. */ 3180 3181/* static void SetIndexSrc(comedi_device *dev, enc_private *k, uint16_t value ) */ 3182/* { */ 3183/* DEBUG("SetIndexSrc: set index src enter 3700\n"); */ 3184/* k->SetMode(dev, k, (uint16_t)( ( k->GetMode(dev, k ) & ~STDMSK_INDXSRC ) | ( (value != 0) << STDBIT_INDXSRC ) ), FALSE ); */ 3185/* } */ 3186 3187/* static uint16_t GetIndexSrc(comedi_device *dev, enc_private *k ) */ 3188/* { */ 3189/* return ( k->GetMode(dev, k ) >> STDBIT_INDXSRC ) & 1; */ 3190/* } */ 3191 3192/* Generate an index pulse. */ 3193 3194static void PulseIndex_A(comedi_device * dev, enc_private * k) 3195{ 3196 register uint16_t cra; 3197 3198 DEBUG("PulseIndex_A: pulse index enter\n"); 3199 3200 cra = DEBIread(dev, k->MyCRA); /* Pulse index. */ 3201 DEBIwrite(dev, k->MyCRA, (uint16_t) (cra ^ CRAMSK_INDXPOL_A)); 3202 DEBUG("PulseIndex_A: pulse index step1\n"); 3203 DEBIwrite(dev, k->MyCRA, cra); 3204} 3205 3206static void PulseIndex_B(comedi_device * dev, enc_private * k) 3207{ 3208 register uint16_t crb; 3209 3210 crb = DEBIread(dev, k->MyCRB) & ~CRBMSK_INTCTRL; /* Pulse index. */ 3211 DEBIwrite(dev, k->MyCRB, (uint16_t) (crb ^ CRBMSK_INDXPOL_B)); 3212 DEBIwrite(dev, k->MyCRB, crb); 3213} 3214 3215/* Write value into counter preload register. */ 3216 3217static void Preload(comedi_device * dev, enc_private * k, uint32_t value) 3218{ 3219 DEBUG("Preload: preload enter\n"); 3220 DEBIwrite(dev, (uint16_t) (k->MyLatchLsw), (uint16_t) value); /* Write value to preload register. */ 3221 DEBUG("Preload: preload step 1\n"); 3222 DEBIwrite(dev, (uint16_t) (k->MyLatchLsw + 2), 3223 (uint16_t) (value >> 16)); 3224} 3225 3226static void CountersInit(comedi_device * dev) 3227{ 3228 int chan; 3229 enc_private *k; 3230 uint16_t Setup = (LOADSRC_INDX << BF_LOADSRC) | /* Preload upon */ 3231 /* index. */ 3232 (INDXSRC_SOFT << BF_INDXSRC) | /* Disable hardware index. */ 3233 (CLKSRC_COUNTER << BF_CLKSRC) | /* Operating mode is counter. */ 3234 (CLKPOL_POS << BF_CLKPOL) | /* Active high clock. */ 3235 (CNTDIR_UP << BF_CLKPOL) | /* Count direction is up. */ 3236 (CLKMULT_1X << BF_CLKMULT) | /* Clock multiplier is 1x. */ 3237 (CLKENAB_INDEX << BF_CLKENAB); /* Enabled by index */ 3238 3239 /* Disable all counter interrupts and clear any captured counter events. */ 3240 for (chan = 0; chan < S626_ENCODER_CHANNELS; chan++) { 3241 k = &encpriv[chan]; 3242 k->SetMode(dev, k, Setup, TRUE); 3243 k->SetIntSrc(dev, k, 0); 3244 k->ResetCapFlags(dev, k); 3245 k->SetEnable(dev, k, CLKENAB_ALWAYS); 3246 } 3247 DEBUG("CountersInit: counters initialized \n"); 3248 3249} 3250