s626.c revision f10fe5742ba6ad6a2219cbe774e1b9d3db0ef23d
1/* 2 comedi/drivers/s626.c 3 Sensoray s626 Comedi driver 4 5 COMEDI - Linux Control and Measurement Device Interface 6 Copyright (C) 2000 David A. Schleef <ds@schleef.org> 7 8 Based on Sensoray Model 626 Linux driver Version 0.2 9 Copyright (C) 2002-2004 Sensoray Co., Inc. 10 11 This program is free software; you can redistribute it and/or modify 12 it under the terms of the GNU General Public License as published by 13 the Free Software Foundation; either version 2 of the License, or 14 (at your option) any later version. 15 16 This program is distributed in the hope that it will be useful, 17 but WITHOUT ANY WARRANTY; without even the implied warranty of 18 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 19 GNU General Public License for more details. 20 21 You should have received a copy of the GNU General Public License 22 along with this program; if not, write to the Free Software 23 Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. 24 25*/ 26 27/* 28Driver: s626 29Description: Sensoray 626 driver 30Devices: [Sensoray] 626 (s626) 31Authors: Gianluca Palli <gpalli@deis.unibo.it>, 32Updated: Fri, 15 Feb 2008 10:28:42 +0000 33Status: experimental 34 35Configuration options: 36 [0] - PCI bus of device (optional) 37 [1] - PCI slot of device (optional) 38 If bus/slot is not specified, the first supported 39 PCI device found will be used. 40 41INSN_CONFIG instructions: 42 analog input: 43 none 44 45 analog output: 46 none 47 48 digital channel: 49 s626 has 3 dio subdevices (2,3 and 4) each with 16 i/o channels 50 supported configuration options: 51 INSN_CONFIG_DIO_QUERY 52 COMEDI_INPUT 53 COMEDI_OUTPUT 54 55 encoder: 56 Every channel must be configured before reading. 57 58 Example code 59 60 insn.insn=INSN_CONFIG; //configuration instruction 61 insn.n=1; //number of operation (must be 1) 62 insn.data=&initialvalue; //initial value loaded into encoder 63 //during configuration 64 insn.subdev=5; //encoder subdevice 65 insn.chanspec=CR_PACK(encoder_channel,0,AREF_OTHER); //encoder_channel 66 //to configure 67 68 comedi_do_insn(cf,&insn); //executing configuration 69*/ 70 71#include <linux/kernel.h> 72#include <linux/types.h> 73 74#include "../comedidev.h" 75 76#include "comedi_pci.h" 77 78#include "comedi_fc.h" 79#include "s626.h" 80 81MODULE_AUTHOR("Gianluca Palli <gpalli@deis.unibo.it>"); 82MODULE_DESCRIPTION("Sensoray 626 Comedi driver module"); 83MODULE_LICENSE("GPL"); 84 85typedef struct s626_board_struct { 86 const char *name; 87 int ai_chans; 88 int ai_bits; 89 int ao_chans; 90 int ao_bits; 91 int dio_chans; 92 int dio_banks; 93 int enc_chans; 94} s626_board; 95 96static const s626_board s626_boards[] = { 97 { 98 name: "s626", 99 ai_chans : S626_ADC_CHANNELS, 100 ai_bits: 14, 101 ao_chans : S626_DAC_CHANNELS, 102 ao_bits: 13, 103 dio_chans : S626_DIO_CHANNELS, 104 dio_banks : S626_DIO_BANKS, 105 enc_chans : S626_ENCODER_CHANNELS, 106 } 107}; 108 109#define thisboard ((const s626_board *)dev->board_ptr) 110#define PCI_VENDOR_ID_S626 0x1131 111#define PCI_DEVICE_ID_S626 0x7146 112 113static DEFINE_PCI_DEVICE_TABLE(s626_pci_table) = { 114 {PCI_VENDOR_ID_S626, PCI_DEVICE_ID_S626, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 115 0}, 116 {0} 117}; 118 119MODULE_DEVICE_TABLE(pci, s626_pci_table); 120 121static int s626_attach(comedi_device *dev, comedi_devconfig *it); 122static int s626_detach(comedi_device *dev); 123 124static comedi_driver driver_s626 = { 125 driver_name:"s626", 126 module : THIS_MODULE, 127 attach : s626_attach, 128 detach : s626_detach, 129}; 130 131typedef struct { 132 struct pci_dev *pdev; 133 void *base_addr; 134 int got_regions; 135 short allocatedBuf; 136 uint8_t ai_cmd_running; /* ai_cmd is running */ 137 uint8_t ai_continous; /* continous aquisition */ 138 int ai_sample_count; /* number of samples to aquire */ 139 unsigned int ai_sample_timer; 140 /* time between samples in units of the timer */ 141 int ai_convert_count; /* conversion counter */ 142 unsigned int ai_convert_timer; 143 /* time between conversion in units of the timer */ 144 uint16_t CounterIntEnabs; 145 /* Counter interrupt enable mask for MISC2 register. */ 146 uint8_t AdcItems; /* Number of items in ADC poll list. */ 147 DMABUF RPSBuf; /* DMA buffer used to hold ADC (RPS1) program. */ 148 DMABUF ANABuf; 149 /* DMA buffer used to receive ADC data and hold DAC data. */ 150 uint32_t *pDacWBuf; 151 /* Pointer to logical adrs of DMA buffer used to hold DAC data. */ 152 uint16_t Dacpol; /* Image of DAC polarity register. */ 153 uint8_t TrimSetpoint[12]; /* Images of TrimDAC setpoints */ 154 uint16_t ChargeEnabled; /* Image of MISC2 Battery */ 155 /* Charge Enabled (0 or WRMISC2_CHARGE_ENABLE). */ 156 uint16_t WDInterval; /* Image of MISC2 watchdog interval control bits. */ 157 uint32_t I2CAdrs; 158 /* I2C device address for onboard EEPROM (board rev dependent). */ 159 /* short I2Cards; */ 160 lsampl_t ao_readback[S626_DAC_CHANNELS]; 161} s626_private; 162 163typedef struct { 164 uint16_t RDDIn; 165 uint16_t WRDOut; 166 uint16_t RDEdgSel; 167 uint16_t WREdgSel; 168 uint16_t RDCapSel; 169 uint16_t WRCapSel; 170 uint16_t RDCapFlg; 171 uint16_t RDIntSel; 172 uint16_t WRIntSel; 173} dio_private; 174 175static dio_private dio_private_A = { 176 RDDIn:LP_RDDINA, 177 WRDOut : LP_WRDOUTA, 178 RDEdgSel : LP_RDEDGSELA, 179 WREdgSel : LP_WREDGSELA, 180 RDCapSel : LP_RDCAPSELA, 181 WRCapSel : LP_WRCAPSELA, 182 RDCapFlg : LP_RDCAPFLGA, 183 RDIntSel : LP_RDINTSELA, 184 WRIntSel : LP_WRINTSELA, 185}; 186 187static dio_private dio_private_B = { 188 RDDIn:LP_RDDINB, 189 WRDOut : LP_WRDOUTB, 190 RDEdgSel : LP_RDEDGSELB, 191 WREdgSel : LP_WREDGSELB, 192 RDCapSel : LP_RDCAPSELB, 193 WRCapSel : LP_WRCAPSELB, 194 RDCapFlg : LP_RDCAPFLGB, 195 RDIntSel : LP_RDINTSELB, 196 WRIntSel : LP_WRINTSELB, 197}; 198 199static dio_private dio_private_C = { 200 RDDIn:LP_RDDINC, 201 WRDOut : LP_WRDOUTC, 202 RDEdgSel : LP_RDEDGSELC, 203 WREdgSel : LP_WREDGSELC, 204 RDCapSel : LP_RDCAPSELC, 205 WRCapSel : LP_WRCAPSELC, 206 RDCapFlg : LP_RDCAPFLGC, 207 RDIntSel : LP_RDINTSELC, 208 WRIntSel : LP_WRINTSELC, 209}; 210 211/* to group dio devices (48 bits mask and data are not allowed ???) 212static dio_private *dio_private_word[]={ 213 &dio_private_A, 214 &dio_private_B, 215 &dio_private_C, 216}; 217*/ 218 219#define devpriv ((s626_private *)dev->private) 220#define diopriv ((dio_private *)s->private) 221 222COMEDI_PCI_INITCLEANUP_NOMODULE(driver_s626, s626_pci_table); 223 224/* ioctl routines */ 225static int s626_ai_insn_config(comedi_device *dev, comedi_subdevice *s, 226 comedi_insn *insn, lsampl_t *data); 227/* static int s626_ai_rinsn(comedi_device *dev,comedi_subdevice *s,comedi_insn *insn,lsampl_t *data); */ 228static int s626_ai_insn_read(comedi_device *dev, comedi_subdevice *s, 229 comedi_insn *insn, lsampl_t *data); 230static int s626_ai_cmd(comedi_device *dev, comedi_subdevice *s); 231static int s626_ai_cmdtest(comedi_device *dev, comedi_subdevice *s, 232 comedi_cmd *cmd); 233static int s626_ai_cancel(comedi_device *dev, comedi_subdevice *s); 234static int s626_ao_winsn(comedi_device *dev, comedi_subdevice *s, 235 comedi_insn *insn, lsampl_t *data); 236static int s626_ao_rinsn(comedi_device *dev, comedi_subdevice *s, 237 comedi_insn *insn, lsampl_t *data); 238static int s626_dio_insn_bits(comedi_device *dev, comedi_subdevice *s, 239 comedi_insn *insn, lsampl_t *data); 240static int s626_dio_insn_config(comedi_device *dev, comedi_subdevice *s, 241 comedi_insn *insn, lsampl_t *data); 242static int s626_dio_set_irq(comedi_device *dev, unsigned int chan); 243static int s626_dio_reset_irq(comedi_device *dev, unsigned int gruop, 244 unsigned int mask); 245static int s626_dio_clear_irq(comedi_device *dev); 246static int s626_enc_insn_config(comedi_device *dev, comedi_subdevice *s, 247 comedi_insn *insn, lsampl_t *data); 248static int s626_enc_insn_read(comedi_device *dev, comedi_subdevice *s, 249 comedi_insn *insn, lsampl_t *data); 250static int s626_enc_insn_write(comedi_device *dev, comedi_subdevice *s, 251 comedi_insn *insn, lsampl_t *data); 252static int s626_ns_to_timer(int *nanosec, int round_mode); 253static int s626_ai_load_polllist(uint8_t *ppl, comedi_cmd *cmd); 254static int s626_ai_inttrig(comedi_device *dev, comedi_subdevice *s, 255 unsigned int trignum); 256static irqreturn_t s626_irq_handler(int irq, void *d PT_REGS_ARG); 257static lsampl_t s626_ai_reg_to_uint(int data); 258/* static lsampl_t s626_uint_to_reg(comedi_subdevice *s, int data); */ 259 260/* end ioctl routines */ 261 262/* internal routines */ 263static void s626_dio_init(comedi_device *dev); 264static void ResetADC(comedi_device *dev, uint8_t *ppl); 265static void LoadTrimDACs(comedi_device *dev); 266static void WriteTrimDAC(comedi_device *dev, uint8_t LogicalChan, 267 uint8_t DacData); 268static uint8_t I2Cread(comedi_device *dev, uint8_t addr); 269static uint32_t I2Chandshake(comedi_device *dev, uint32_t val); 270static void SetDAC(comedi_device *dev, uint16_t chan, short dacdata); 271static void SendDAC(comedi_device *dev, uint32_t val); 272static void WriteMISC2(comedi_device *dev, uint16_t NewImage); 273static void DEBItransfer(comedi_device *dev); 274static uint16_t DEBIread(comedi_device *dev, uint16_t addr); 275static void DEBIwrite(comedi_device *dev, uint16_t addr, uint16_t wdata); 276static void DEBIreplace(comedi_device *dev, uint16_t addr, uint16_t mask, 277 uint16_t wdata); 278static void CloseDMAB(comedi_device *dev, DMABUF *pdma, size_t bsize); 279 280/* COUNTER OBJECT ------------------------------------------------ */ 281typedef struct enc_private_struct { 282 /* Pointers to functions that differ for A and B counters: */ 283 uint16_t(*GetEnable) (comedi_device *dev, struct enc_private_struct *); /* Return clock enable. */ 284 uint16_t(*GetIntSrc) (comedi_device *dev, struct enc_private_struct *); /* Return interrupt source. */ 285 uint16_t(*GetLoadTrig) (comedi_device *dev, struct enc_private_struct *); /* Return preload trigger source. */ 286 uint16_t(*GetMode) (comedi_device *dev, struct enc_private_struct *); /* Return standardized operating mode. */ 287 void (*PulseIndex) (comedi_device *dev, struct enc_private_struct *); /* Generate soft index strobe. */ 288 void (*SetEnable) (comedi_device *dev, struct enc_private_struct *, uint16_t enab); /* Program clock enable. */ 289 void (*SetIntSrc) (comedi_device *dev, struct enc_private_struct *, uint16_t IntSource); /* Program interrupt source. */ 290 void (*SetLoadTrig) (comedi_device *dev, struct enc_private_struct *, uint16_t Trig); /* Program preload trigger source. */ 291 void (*SetMode) (comedi_device *dev, struct enc_private_struct *, uint16_t Setup, uint16_t DisableIntSrc); /* Program standardized operating mode. */ 292 void (*ResetCapFlags) (comedi_device *dev, struct enc_private_struct *); /* Reset event capture flags. */ 293 294 uint16_t MyCRA; /* Address of CRA register. */ 295 uint16_t MyCRB; /* Address of CRB register. */ 296 uint16_t MyLatchLsw; /* Address of Latch least-significant-word */ 297 /* register. */ 298 uint16_t MyEventBits[4]; /* Bit translations for IntSrc -->RDMISC2. */ 299} enc_private; /* counter object */ 300 301#define encpriv ((enc_private *)(dev->subdevices+5)->private) 302 303/* counters routines */ 304static void s626_timer_load(comedi_device *dev, enc_private *k, int tick); 305static uint32_t ReadLatch(comedi_device *dev, enc_private *k); 306static void ResetCapFlags_A(comedi_device *dev, enc_private *k); 307static void ResetCapFlags_B(comedi_device *dev, enc_private *k); 308static uint16_t GetMode_A(comedi_device *dev, enc_private *k); 309static uint16_t GetMode_B(comedi_device *dev, enc_private *k); 310static void SetMode_A(comedi_device *dev, enc_private *k, uint16_t Setup, 311 uint16_t DisableIntSrc); 312static void SetMode_B(comedi_device *dev, enc_private *k, uint16_t Setup, 313 uint16_t DisableIntSrc); 314static void SetEnable_A(comedi_device *dev, enc_private *k, uint16_t enab); 315static void SetEnable_B(comedi_device *dev, enc_private *k, uint16_t enab); 316static uint16_t GetEnable_A(comedi_device *dev, enc_private *k); 317static uint16_t GetEnable_B(comedi_device *dev, enc_private *k); 318static void SetLatchSource(comedi_device *dev, enc_private *k, 319 uint16_t value); 320/* static uint16_t GetLatchSource(comedi_device *dev, enc_private *k ); */ 321static void SetLoadTrig_A(comedi_device *dev, enc_private *k, uint16_t Trig); 322static void SetLoadTrig_B(comedi_device *dev, enc_private *k, uint16_t Trig); 323static uint16_t GetLoadTrig_A(comedi_device *dev, enc_private *k); 324static uint16_t GetLoadTrig_B(comedi_device *dev, enc_private *k); 325static void SetIntSrc_B(comedi_device *dev, enc_private *k, 326 uint16_t IntSource); 327static void SetIntSrc_A(comedi_device *dev, enc_private *k, 328 uint16_t IntSource); 329static uint16_t GetIntSrc_A(comedi_device *dev, enc_private *k); 330static uint16_t GetIntSrc_B(comedi_device *dev, enc_private *k); 331/* static void SetClkMult(comedi_device *dev, enc_private *k, uint16_t value ) ; */ 332/* static uint16_t GetClkMult(comedi_device *dev, enc_private *k ) ; */ 333/* static void SetIndexPol(comedi_device *dev, enc_private *k, uint16_t value ); */ 334/* static uint16_t GetClkPol(comedi_device *dev, enc_private *k ) ; */ 335/* static void SetIndexSrc( comedi_device *dev,enc_private *k, uint16_t value ); */ 336/* static uint16_t GetClkSrc( comedi_device *dev,enc_private *k ); */ 337/* static void SetIndexSrc( comedi_device *dev,enc_private *k, uint16_t value ); */ 338/* static uint16_t GetIndexSrc( comedi_device *dev,enc_private *k ); */ 339static void PulseIndex_A(comedi_device *dev, enc_private *k); 340static void PulseIndex_B(comedi_device *dev, enc_private *k); 341static void Preload(comedi_device *dev, enc_private *k, uint32_t value); 342static void CountersInit(comedi_device *dev); 343/* end internal routines */ 344 345/* Counter objects constructor. */ 346 347/* Counter overflow/index event flag masks for RDMISC2. */ 348#define INDXMASK(C) (1 << (((C) > 2) ? ((C) * 2 - 1) : ((C) * 2 + 4))) 349#define OVERMASK(C) (1 << (((C) > 2) ? ((C) * 2 + 5) : ((C) * 2 + 10))) 350#define EVBITS(C) { 0, OVERMASK(C), INDXMASK(C), OVERMASK(C) | INDXMASK(C) } 351 352/* Translation table to map IntSrc into equivalent RDMISC2 event flag bits. */ 353/* static const uint16_t EventBits[][4] = { EVBITS(0), EVBITS(1), EVBITS(2), EVBITS(3), EVBITS(4), EVBITS(5) }; */ 354 355/* enc_private; */ 356static enc_private enc_private_data[] = { 357 { 358 GetEnable:GetEnable_A, 359 GetIntSrc : GetIntSrc_A, 360 GetLoadTrig : GetLoadTrig_A, 361 GetMode: GetMode_A, 362 PulseIndex : PulseIndex_A, 363 SetEnable : SetEnable_A, 364 SetIntSrc : SetIntSrc_A, 365 SetLoadTrig : SetLoadTrig_A, 366 SetMode: SetMode_A, 367 ResetCapFlags : ResetCapFlags_A, 368 MyCRA: LP_CR0A, 369 MyCRB: LP_CR0B, 370 MyLatchLsw : LP_CNTR0ALSW, 371 MyEventBits : EVBITS(0), 372 }, 373 { 374 GetEnable:GetEnable_A, 375 GetIntSrc : GetIntSrc_A, 376 GetLoadTrig : GetLoadTrig_A, 377 GetMode: GetMode_A, 378 PulseIndex : PulseIndex_A, 379 SetEnable : SetEnable_A, 380 SetIntSrc : SetIntSrc_A, 381 SetLoadTrig : SetLoadTrig_A, 382 SetMode: SetMode_A, 383 ResetCapFlags : ResetCapFlags_A, 384 MyCRA: LP_CR1A, 385 MyCRB: LP_CR1B, 386 MyLatchLsw : LP_CNTR1ALSW, 387 MyEventBits : EVBITS(1), 388 }, 389 { 390 GetEnable:GetEnable_A, 391 GetIntSrc : GetIntSrc_A, 392 GetLoadTrig : GetLoadTrig_A, 393 GetMode: GetMode_A, 394 PulseIndex : PulseIndex_A, 395 SetEnable : SetEnable_A, 396 SetIntSrc : SetIntSrc_A, 397 SetLoadTrig : SetLoadTrig_A, 398 SetMode: SetMode_A, 399 ResetCapFlags : ResetCapFlags_A, 400 MyCRA: LP_CR2A, 401 MyCRB: LP_CR2B, 402 MyLatchLsw : LP_CNTR2ALSW, 403 MyEventBits : EVBITS(2), 404 }, 405 { 406 GetEnable:GetEnable_B, 407 GetIntSrc : GetIntSrc_B, 408 GetLoadTrig : GetLoadTrig_B, 409 GetMode: GetMode_B, 410 PulseIndex : PulseIndex_B, 411 SetEnable : SetEnable_B, 412 SetIntSrc : SetIntSrc_B, 413 SetLoadTrig : SetLoadTrig_B, 414 SetMode: SetMode_B, 415 ResetCapFlags : ResetCapFlags_B, 416 MyCRA: LP_CR0A, 417 MyCRB: LP_CR0B, 418 MyLatchLsw : LP_CNTR0BLSW, 419 MyEventBits : EVBITS(3), 420 }, 421 { 422 GetEnable:GetEnable_B, 423 GetIntSrc : GetIntSrc_B, 424 GetLoadTrig : GetLoadTrig_B, 425 GetMode: GetMode_B, 426 PulseIndex : PulseIndex_B, 427 SetEnable : SetEnable_B, 428 SetIntSrc : SetIntSrc_B, 429 SetLoadTrig : SetLoadTrig_B, 430 SetMode: SetMode_B, 431 ResetCapFlags : ResetCapFlags_B, 432 MyCRA: LP_CR1A, 433 MyCRB: LP_CR1B, 434 MyLatchLsw : LP_CNTR1BLSW, 435 MyEventBits : EVBITS(4), 436 }, 437 { 438 GetEnable:GetEnable_B, 439 GetIntSrc : GetIntSrc_B, 440 GetLoadTrig : GetLoadTrig_B, 441 GetMode: GetMode_B, 442 PulseIndex : PulseIndex_B, 443 SetEnable : SetEnable_B, 444 SetIntSrc : SetIntSrc_B, 445 SetLoadTrig : SetLoadTrig_B, 446 SetMode: SetMode_B, 447 ResetCapFlags : ResetCapFlags_B, 448 MyCRA: LP_CR2A, 449 MyCRB: LP_CR2B, 450 MyLatchLsw : LP_CNTR2BLSW, 451 MyEventBits : EVBITS(5), 452 }, 453}; 454 455/* enab/disable a function or test status bit(s) that are accessed */ 456/* through Main Control Registers 1 or 2. */ 457#define MC_ENABLE(REGADRS, CTRLWORD) writel(((uint32_t)(CTRLWORD) << 16) | (uint32_t)(CTRLWORD), devpriv->base_addr+(REGADRS)) 458 459#define MC_DISABLE(REGADRS, CTRLWORD) writel((uint32_t)(CTRLWORD) << 16 , devpriv->base_addr+(REGADRS)) 460 461#define MC_TEST(REGADRS, CTRLWORD) ((readl(devpriv->base_addr+(REGADRS)) & CTRLWORD) != 0) 462 463/* #define WR7146(REGARDS,CTRLWORD) 464 writel(CTRLWORD,(uint32_t)(devpriv->base_addr+(REGARDS))) */ 465#define WR7146(REGARDS, CTRLWORD) writel(CTRLWORD, devpriv->base_addr+(REGARDS)) 466 467/* #define RR7146(REGARDS) 468 readl((uint32_t)(devpriv->base_addr+(REGARDS))) */ 469#define RR7146(REGARDS) readl(devpriv->base_addr+(REGARDS)) 470 471#define BUGFIX_STREG(REGADRS) (REGADRS - 4) 472 473/* Write a time slot control record to TSL2. */ 474#define VECTPORT(VECTNUM) (P_TSL2 + ((VECTNUM) << 2)) 475#define SETVECT(VECTNUM, VECTVAL) WR7146(VECTPORT(VECTNUM), (VECTVAL)) 476 477/* Code macros used for constructing I2C command bytes. */ 478#define I2C_B2(ATTR, VAL) (((ATTR) << 6) | ((VAL) << 24)) 479#define I2C_B1(ATTR, VAL) (((ATTR) << 4) | ((VAL) << 16)) 480#define I2C_B0(ATTR, VAL) (((ATTR) << 2) | ((VAL) << 8)) 481 482static const comedi_lrange s626_range_table = { 2, { 483 RANGE(-5, 5), 484 RANGE(-10, 10), 485 } 486}; 487 488static int s626_attach(comedi_device *dev, comedi_devconfig *it) 489{ 490/* uint8_t PollList; */ 491/* uint16_t AdcData; */ 492/* uint16_t StartVal; */ 493/* uint16_t index; */ 494/* unsigned int data[16]; */ 495 int result; 496 int i; 497 int ret; 498 resource_size_t resourceStart; 499 dma_addr_t appdma; 500 comedi_subdevice *s; 501 struct pci_dev *pdev; 502 503 if (alloc_private(dev, sizeof(s626_private)) < 0) 504 return -ENOMEM; 505 506 for (pdev = pci_get_device(PCI_VENDOR_ID_S626, PCI_DEVICE_ID_S626, 507 NULL); pdev != NULL; 508 pdev = pci_get_device(PCI_VENDOR_ID_S626, 509 PCI_DEVICE_ID_S626, pdev)) { 510 if (it->options[0] || it->options[1]) { 511 if (pdev->bus->number == it->options[0] && 512 PCI_SLOT(pdev->devfn) == it->options[1]) { 513 /* matches requested bus/slot */ 514 break; 515 } 516 } else { 517 /* no bus/slot specified */ 518 break; 519 } 520 } 521 devpriv->pdev = pdev; 522 523 if (pdev == NULL) { 524 printk("s626_attach: Board not present!!!\n"); 525 return -ENODEV; 526 } 527 528 result = comedi_pci_enable(pdev, "s626"); 529 if (result < 0) { 530 printk("s626_attach: comedi_pci_enable fails\n"); 531 return -ENODEV; 532 } 533 devpriv->got_regions = 1; 534 535 resourceStart = pci_resource_start(devpriv->pdev, 0); 536 537 devpriv->base_addr = ioremap(resourceStart, SIZEOF_ADDRESS_SPACE); 538 if (devpriv->base_addr == NULL) { 539 printk("s626_attach: IOREMAP failed\n"); 540 return -ENODEV; 541 } 542 543 if (devpriv->base_addr) { 544 /* disable master interrupt */ 545 writel(0, devpriv->base_addr + P_IER); 546 547 /* soft reset */ 548 writel(MC1_SOFT_RESET, devpriv->base_addr + P_MC1); 549 550 /* DMA FIXME DMA// */ 551 DEBUG("s626_attach: DMA ALLOCATION\n"); 552 553 /* adc buffer allocation */ 554 devpriv->allocatedBuf = 0; 555 556 devpriv->ANABuf.LogicalBase = 557 pci_alloc_consistent(devpriv->pdev, DMABUF_SIZE, &appdma); 558 559 if (devpriv->ANABuf.LogicalBase == NULL) { 560 printk("s626_attach: DMA Memory mapping error\n"); 561 return -ENOMEM; 562 } 563 564 devpriv->ANABuf.PhysicalBase = appdma; 565 566 DEBUG("s626_attach: AllocDMAB ADC Logical=%p, bsize=%d, Physical=0x%x\n", devpriv->ANABuf.LogicalBase, DMABUF_SIZE, (uint32_t) devpriv->ANABuf.PhysicalBase); 567 568 devpriv->allocatedBuf++; 569 570 devpriv->RPSBuf.LogicalBase = 571 pci_alloc_consistent(devpriv->pdev, DMABUF_SIZE, &appdma); 572 573 if (devpriv->RPSBuf.LogicalBase == NULL) { 574 printk("s626_attach: DMA Memory mapping error\n"); 575 return -ENOMEM; 576 } 577 578 devpriv->RPSBuf.PhysicalBase = appdma; 579 580 DEBUG("s626_attach: AllocDMAB RPS Logical=%p, bsize=%d, Physical=0x%x\n", devpriv->RPSBuf.LogicalBase, DMABUF_SIZE, (uint32_t) devpriv->RPSBuf.PhysicalBase); 581 582 devpriv->allocatedBuf++; 583 584 } 585 586 dev->board_ptr = s626_boards; 587 dev->board_name = thisboard->name; 588 589 if (alloc_subdevices(dev, 6) < 0) 590 return -ENOMEM; 591 592 dev->iobase = (unsigned long)devpriv->base_addr; 593 dev->irq = devpriv->pdev->irq; 594 595 /* set up interrupt handler */ 596 if (dev->irq == 0) { 597 printk(" unknown irq (bad)\n"); 598 } else { 599 ret = comedi_request_irq(dev->irq, s626_irq_handler, 600 IRQF_SHARED, "s626", dev); 601 602 if (ret < 0) { 603 printk(" irq not available\n"); 604 dev->irq = 0; 605 } 606 } 607 608 DEBUG("s626_attach: -- it opts %d,%d -- \n", 609 it->options[0], it->options[1]); 610 611 s = dev->subdevices + 0; 612 /* analog input subdevice */ 613 dev->read_subdev = s; 614 /* we support single-ended (ground) and differential */ 615 s->type = COMEDI_SUBD_AI; 616 s->subdev_flags = SDF_READABLE | SDF_DIFF | SDF_CMD_READ; 617 s->n_chan = thisboard->ai_chans; 618 s->maxdata = (0xffff >> 2); 619 s->range_table = &s626_range_table; 620 s->len_chanlist = thisboard->ai_chans; /* This is the maximum chanlist 621 length that the board can 622 handle */ 623 s->insn_config = s626_ai_insn_config; 624 s->insn_read = s626_ai_insn_read; 625 s->do_cmd = s626_ai_cmd; 626 s->do_cmdtest = s626_ai_cmdtest; 627 s->cancel = s626_ai_cancel; 628 629 s = dev->subdevices + 1; 630 /* analog output subdevice */ 631 s->type = COMEDI_SUBD_AO; 632 s->subdev_flags = SDF_WRITABLE | SDF_READABLE; 633 s->n_chan = thisboard->ao_chans; 634 s->maxdata = (0x3fff); 635 s->range_table = &range_bipolar10; 636 s->insn_write = s626_ao_winsn; 637 s->insn_read = s626_ao_rinsn; 638 639 s = dev->subdevices + 2; 640 /* digital I/O subdevice */ 641 s->type = COMEDI_SUBD_DIO; 642 s->subdev_flags = SDF_WRITABLE | SDF_READABLE; 643 s->n_chan = S626_DIO_CHANNELS; 644 s->maxdata = 1; 645 s->io_bits = 0xffff; 646 s->private = &dio_private_A; 647 s->range_table = &range_digital; 648 s->insn_config = s626_dio_insn_config; 649 s->insn_bits = s626_dio_insn_bits; 650 651 s = dev->subdevices + 3; 652 /* digital I/O subdevice */ 653 s->type = COMEDI_SUBD_DIO; 654 s->subdev_flags = SDF_WRITABLE | SDF_READABLE; 655 s->n_chan = 16; 656 s->maxdata = 1; 657 s->io_bits = 0xffff; 658 s->private = &dio_private_B; 659 s->range_table = &range_digital; 660 s->insn_config = s626_dio_insn_config; 661 s->insn_bits = s626_dio_insn_bits; 662 663 s = dev->subdevices + 4; 664 /* digital I/O subdevice */ 665 s->type = COMEDI_SUBD_DIO; 666 s->subdev_flags = SDF_WRITABLE | SDF_READABLE; 667 s->n_chan = 16; 668 s->maxdata = 1; 669 s->io_bits = 0xffff; 670 s->private = &dio_private_C; 671 s->range_table = &range_digital; 672 s->insn_config = s626_dio_insn_config; 673 s->insn_bits = s626_dio_insn_bits; 674 675 s = dev->subdevices + 5; 676 /* encoder (counter) subdevice */ 677 s->type = COMEDI_SUBD_COUNTER; 678 s->subdev_flags = SDF_WRITABLE | SDF_READABLE | SDF_LSAMPL; 679 s->n_chan = thisboard->enc_chans; 680 s->private = enc_private_data; 681 s->insn_config = s626_enc_insn_config; 682 s->insn_read = s626_enc_insn_read; 683 s->insn_write = s626_enc_insn_write; 684 s->maxdata = 0xffffff; 685 s->range_table = &range_unknown; 686 687 /* stop ai_command */ 688 devpriv->ai_cmd_running = 0; 689 690 if (devpriv->base_addr && (devpriv->allocatedBuf == 2)) { 691 dma_addr_t pPhysBuf; 692 uint16_t chan; 693 694 /* enab DEBI and audio pins, enable I2C interface. */ 695 MC_ENABLE(P_MC1, MC1_DEBI | MC1_AUDIO | MC1_I2C); 696 /* Configure DEBI operating mode. */ 697 WR7146(P_DEBICFG, DEBI_CFG_SLAVE16 /* Local bus is 16 */ 698 /* bits wide. */ 699 | (DEBI_TOUT << DEBI_CFG_TOUT_BIT) /* Declare DEBI */ 700 /* transfer timeout */ 701 /* interval. */ 702 | DEBI_SWAP /* Set up byte lane */ 703 /* steering. */ 704 | DEBI_CFG_INTEL); /* Intel-compatible */ 705 /* local bus (DEBI */ 706 /* never times out). */ 707 DEBUG("s626_attach: %d debi init -- %d\n", 708 DEBI_CFG_SLAVE16 | (DEBI_TOUT << DEBI_CFG_TOUT_BIT) | 709 DEBI_SWAP | DEBI_CFG_INTEL, 710 DEBI_CFG_INTEL | DEBI_CFG_TOQ | DEBI_CFG_INCQ | 711 DEBI_CFG_16Q); 712 713 /* DEBI INIT S626 WR7146( P_DEBICFG, DEBI_CFG_INTEL | DEBI_CFG_TOQ */ 714 /* | DEBI_CFG_INCQ| DEBI_CFG_16Q); //end */ 715 716 /* Paging is disabled. */ 717 WR7146(P_DEBIPAGE, DEBI_PAGE_DISABLE); /* Disable MMU paging. */ 718 719 /* Init GPIO so that ADC Start* is negated. */ 720 WR7146(P_GPIO, GPIO_BASE | GPIO1_HI); 721 722 /* IsBoardRevA is a boolean that indicates whether the board is RevA. 723 * 724 * VERSION 2.01 CHANGE: REV A & B BOARDS NOW SUPPORTED BY DYNAMIC 725 * EEPROM ADDRESS SELECTION. Initialize the I2C interface, which 726 * is used to access the onboard serial EEPROM. The EEPROM's I2C 727 * DeviceAddress is hardwired to a value that is dependent on the 728 * 626 board revision. On all board revisions, the EEPROM stores 729 * TrimDAC calibration constants for analog I/O. On RevB and 730 * higher boards, the DeviceAddress is hardwired to 0 to enable 731 * the EEPROM to also store the PCI SubVendorID and SubDeviceID; 732 * this is the address at which the SAA7146 expects a 733 * configuration EEPROM to reside. On RevA boards, the EEPROM 734 * device address, which is hardwired to 4, prevents the SAA7146 735 * from retrieving PCI sub-IDs, so the SAA7146 uses its built-in 736 * default values, instead. 737 */ 738 739 /* devpriv->I2Cards= IsBoardRevA ? 0xA8 : 0xA0; // Set I2C EEPROM */ 740 /* DeviceType (0xA0) */ 741 /* and DeviceAddress<<1. */ 742 743 devpriv->I2CAdrs = 0xA0; /* I2C device address for onboard */ 744 /* eeprom(revb) */ 745 746 /* Issue an I2C ABORT command to halt any I2C operation in */ 747 /* progress and reset BUSY flag. */ 748 WR7146(P_I2CSTAT, I2C_CLKSEL | I2C_ABORT); 749 /* Write I2C control: abort any I2C activity. */ 750 MC_ENABLE(P_MC2, MC2_UPLD_IIC); 751 /* Invoke command upload */ 752 while ((RR7146(P_MC2) & MC2_UPLD_IIC) == 0) 753 ; 754 /* and wait for upload to complete. */ 755 756 /* Per SAA7146 data sheet, write to STATUS reg twice to 757 * reset all I2C error flags. */ 758 for (i = 0; i < 2; i++) { 759 WR7146(P_I2CSTAT, I2C_CLKSEL); 760 /* Write I2C control: reset error flags. */ 761 MC_ENABLE(P_MC2, MC2_UPLD_IIC); /* Invoke command upload */ 762 while (!MC_TEST(P_MC2, MC2_UPLD_IIC)) 763 ; 764 /* and wait for upload to complete. */ 765 } 766 767 /* Init audio interface functional attributes: set DAC/ADC 768 * serial clock rates, invert DAC serial clock so that 769 * DAC data setup times are satisfied, enable DAC serial 770 * clock out. 771 */ 772 773 WR7146(P_ACON2, ACON2_INIT); 774 775 /* Set up TSL1 slot list, which is used to control the 776 * accumulation of ADC data: RSD1 = shift data in on SD1. 777 * SIB_A1 = store data uint8_t at next available location in 778 * FB BUFFER1 register. */ 779 WR7146(P_TSL1, RSD1 | SIB_A1); 780 /* Fetch ADC high data uint8_t. */ 781 WR7146(P_TSL1 + 4, RSD1 | SIB_A1 | EOS); 782 /* Fetch ADC low data uint8_t; end of TSL1. */ 783 784 /* enab TSL1 slot list so that it executes all the time. */ 785 WR7146(P_ACON1, ACON1_ADCSTART); 786 787 /* Initialize RPS registers used for ADC. */ 788 789 /* Physical start of RPS program. */ 790 WR7146(P_RPSADDR1, (uint32_t) devpriv->RPSBuf.PhysicalBase); 791 792 WR7146(P_RPSPAGE1, 0); 793 /* RPS program performs no explicit mem writes. */ 794 WR7146(P_RPS1_TOUT, 0); /* Disable RPS timeouts. */ 795 796 /* SAA7146 BUG WORKAROUND. Initialize SAA7146 ADC interface 797 * to a known state by invoking ADCs until FB BUFFER 1 798 * register shows that it is correctly receiving ADC data. 799 * This is necessary because the SAA7146 ADC interface does 800 * not start up in a defined state after a PCI reset. 801 */ 802 803/* PollList = EOPL; // Create a simple polling */ 804/* // list for analog input */ 805/* // channel 0. */ 806/* ResetADC( dev, &PollList ); */ 807 808/* s626_ai_rinsn(dev,dev->subdevices,NULL,data); //( &AdcData ); // */ 809/* //Get initial ADC */ 810/* //value. */ 811 812/* StartVal = data[0]; */ 813 814/* // VERSION 2.01 CHANGE: TIMEOUT ADDED TO PREVENT HANGED EXECUTION. */ 815/* // Invoke ADCs until the new ADC value differs from the initial */ 816/* // value or a timeout occurs. The timeout protects against the */ 817/* // possibility that the driver is restarting and the ADC data is a */ 818/* // fixed value resulting from the applied ADC analog input being */ 819/* // unusually quiet or at the rail. */ 820 821/* for ( index = 0; index < 500; index++ ) */ 822/* { */ 823/* s626_ai_rinsn(dev,dev->subdevices,NULL,data); */ 824/* AdcData = data[0]; //ReadADC( &AdcData ); */ 825/* if ( AdcData != StartVal ) */ 826/* break; */ 827/* } */ 828 829 /* end initADC */ 830 831 /* init the DAC interface */ 832 833 /* Init Audio2's output DMAC attributes: burst length = 1 834 * DWORD, threshold = 1 DWORD. 835 */ 836 WR7146(P_PCI_BT_A, 0); 837 838 /* Init Audio2's output DMA physical addresses. The protection 839 * address is set to 1 DWORD past the base address so that a 840 * single DWORD will be transferred each time a DMA transfer is 841 * enabled. */ 842 843 pPhysBuf = 844 devpriv->ANABuf.PhysicalBase + 845 (DAC_WDMABUF_OS * sizeof(uint32_t)); 846 847 WR7146(P_BASEA2_OUT, (uint32_t) pPhysBuf); /* Buffer base adrs. */ 848 WR7146(P_PROTA2_OUT, (uint32_t) (pPhysBuf + sizeof(uint32_t))); /* Protection address. */ 849 850 /* Cache Audio2's output DMA buffer logical address. This is 851 * where DAC data is buffered for A2 output DMA transfers. */ 852 devpriv->pDacWBuf = 853 (uint32_t *) devpriv->ANABuf.LogicalBase + 854 DAC_WDMABUF_OS; 855 856 /* Audio2's output channels does not use paging. The protection 857 * violation handling bit is set so that the DMAC will 858 * automatically halt and its PCI address pointer will be reset 859 * when the protection address is reached. */ 860 861 WR7146(P_PAGEA2_OUT, 8); 862 863 /* Initialize time slot list 2 (TSL2), which is used to control 864 * the clock generation for and serialization of data to be sent 865 * to the DAC devices. Slot 0 is a NOP that is used to trap TSL 866 * execution; this permits other slots to be safely modified 867 * without first turning off the TSL sequencer (which is 868 * apparently impossible to do). Also, SD3 (which is driven by a 869 * pull-up resistor) is shifted in and stored to the MSB of 870 * FB_BUFFER2 to be used as evidence that the slot sequence has 871 * not yet finished executing. 872 */ 873 874 SETVECT(0, XSD2 | RSD3 | SIB_A2 | EOS); 875 /* Slot 0: Trap TSL execution, shift 0xFF into FB_BUFFER2. */ 876 877 /* Initialize slot 1, which is constant. Slot 1 causes a 878 * DWORD to be transferred from audio channel 2's output FIFO 879 * to the FIFO's output buffer so that it can be serialized 880 * and sent to the DAC during subsequent slots. All remaining 881 * slots are dynamically populated as required by the target 882 * DAC device. 883 */ 884 SETVECT(1, LF_A2); 885 /* Slot 1: Fetch DWORD from Audio2's output FIFO. */ 886 887 /* Start DAC's audio interface (TSL2) running. */ 888 WR7146(P_ACON1, ACON1_DACSTART); 889 890 /* end init DAC interface */ 891 892 /* Init Trim DACs to calibrated values. Do it twice because the 893 * SAA7146 audio channel does not always reset properly and 894 * sometimes causes the first few TrimDAC writes to malfunction. 895 */ 896 897 LoadTrimDACs(dev); 898 LoadTrimDACs(dev); /* Insurance. */ 899 900 /* Manually init all gate array hardware in case this is a soft 901 * reset (we have no way of determining whether this is a warm 902 * or cold start). This is necessary because the gate array will 903 * reset only in response to a PCI hard reset; there is no soft 904 * reset function. */ 905 906 /* Init all DAC outputs to 0V and init all DAC setpoint and 907 * polarity images. 908 */ 909 for (chan = 0; chan < S626_DAC_CHANNELS; chan++) 910 SetDAC(dev, chan, 0); 911 912 /* Init image of WRMISC2 Battery Charger Enabled control bit. 913 * This image is used when the state of the charger control bit, 914 * which has no direct hardware readback mechanism, is queried. 915 */ 916 devpriv->ChargeEnabled = 0; 917 918 /* Init image of watchdog timer interval in WRMISC2. This image 919 * maintains the value of the control bits of MISC2 are 920 * continuously reset to zero as long as the WD timer is disabled. 921 */ 922 devpriv->WDInterval = 0; 923 924 /* Init Counter Interrupt enab mask for RDMISC2. This mask is 925 * applied against MISC2 when testing to determine which timer 926 * events are requesting interrupt service. 927 */ 928 devpriv->CounterIntEnabs = 0; 929 930 /* Init counters. */ 931 CountersInit(dev); 932 933 /* Without modifying the state of the Battery Backup enab, disable 934 * the watchdog timer, set DIO channels 0-5 to operate in the 935 * standard DIO (vs. counter overflow) mode, disable the battery 936 * charger, and reset the watchdog interval selector to zero. 937 */ 938 WriteMISC2(dev, (uint16_t) (DEBIread(dev, 939 LP_RDMISC2) & MISC2_BATT_ENABLE)); 940 941 /* Initialize the digital I/O subsystem. */ 942 s626_dio_init(dev); 943 944 /* enable interrupt test */ 945 /* writel(IRQ_GPIO3 | IRQ_RPS1,devpriv->base_addr+P_IER); */ 946 } 947 948 DEBUG("s626_attach: comedi%d s626 attached %04x\n", dev->minor, 949 (uint32_t) devpriv->base_addr); 950 951 return 1; 952} 953 954static lsampl_t s626_ai_reg_to_uint(int data) 955{ 956 lsampl_t tempdata; 957 958 tempdata = (data >> 18); 959 if (tempdata & 0x2000) 960 tempdata &= 0x1fff; 961 else 962 tempdata += (1 << 13); 963 964 return tempdata; 965} 966 967/* static lsampl_t s626_uint_to_reg(comedi_subdevice *s, int data){ */ 968/* return 0; */ 969/* } */ 970 971static irqreturn_t s626_irq_handler(int irq, void *d PT_REGS_ARG) 972{ 973 comedi_device *dev = d; 974 comedi_subdevice *s; 975 comedi_cmd *cmd; 976 enc_private *k; 977 unsigned long flags; 978 int32_t *readaddr; 979 uint32_t irqtype, irqstatus; 980 int i = 0; 981 sampl_t tempdata; 982 uint8_t group; 983 uint16_t irqbit; 984 985 DEBUG("s626_irq_handler: interrupt request recieved!!!\n"); 986 987 if (dev->attached == 0) 988 return IRQ_NONE; 989 /* lock to avoid race with comedi_poll */ 990 comedi_spin_lock_irqsave(&dev->spinlock, flags); 991 992 /* save interrupt enable register state */ 993 irqstatus = readl(devpriv->base_addr + P_IER); 994 995 /* read interrupt type */ 996 irqtype = readl(devpriv->base_addr + P_ISR); 997 998 /* disable master interrupt */ 999 writel(0, devpriv->base_addr + P_IER); 1000 1001 /* clear interrupt */ 1002 writel(irqtype, devpriv->base_addr + P_ISR); 1003 1004 /* do somethings */ 1005 DEBUG("s626_irq_handler: interrupt type %d\n", irqtype); 1006 1007 switch (irqtype) { 1008 case IRQ_RPS1: /* end_of_scan occurs */ 1009 1010 DEBUG("s626_irq_handler: RPS1 irq detected\n"); 1011 1012 /* manage ai subdevice */ 1013 s = dev->subdevices; 1014 cmd = &(s->async->cmd); 1015 1016 /* Init ptr to DMA buffer that holds new ADC data. We skip the 1017 * first uint16_t in the buffer because it contains junk data from 1018 * the final ADC of the previous poll list scan. 1019 */ 1020 readaddr = (int32_t *) devpriv->ANABuf.LogicalBase + 1; 1021 1022 /* get the data and hand it over to comedi */ 1023 for (i = 0; i < (s->async->cmd.chanlist_len); i++) { 1024 /* Convert ADC data to 16-bit integer values and copy to application */ 1025 /* buffer. */ 1026 tempdata = s626_ai_reg_to_uint((int)*readaddr); 1027 readaddr++; 1028 1029 /* put data into read buffer */ 1030 /* comedi_buf_put(s->async, tempdata); */ 1031 if (cfc_write_to_buffer(s, tempdata) == 0) 1032 printk("s626_irq_handler: cfc_write_to_buffer error!\n"); 1033 1034 DEBUG("s626_irq_handler: ai channel %d acquired: %d\n", 1035 i, tempdata); 1036 } 1037 1038 /* end of scan occurs */ 1039 s->async->events |= COMEDI_CB_EOS; 1040 1041 if (!(devpriv->ai_continous)) 1042 devpriv->ai_sample_count--; 1043 if (devpriv->ai_sample_count <= 0) { 1044 devpriv->ai_cmd_running = 0; 1045 1046 /* Stop RPS program. */ 1047 MC_DISABLE(P_MC1, MC1_ERPS1); 1048 1049 /* send end of acquisition */ 1050 s->async->events |= COMEDI_CB_EOA; 1051 1052 /* disable master interrupt */ 1053 irqstatus = 0; 1054 } 1055 1056 if (devpriv->ai_cmd_running && cmd->scan_begin_src == TRIG_EXT) { 1057 DEBUG("s626_irq_handler: enable interrupt on dio channel %d\n", cmd->scan_begin_arg); 1058 1059 s626_dio_set_irq(dev, cmd->scan_begin_arg); 1060 1061 DEBUG("s626_irq_handler: External trigger is set!!!\n"); 1062 } 1063 /* tell comedi that data is there */ 1064 DEBUG("s626_irq_handler: events %d\n", s->async->events); 1065 comedi_event(dev, s); 1066 break; 1067 case IRQ_GPIO3: /* check dio and conter interrupt */ 1068 1069 DEBUG("s626_irq_handler: GPIO3 irq detected\n"); 1070 1071 /* manage ai subdevice */ 1072 s = dev->subdevices; 1073 cmd = &(s->async->cmd); 1074 1075 /* s626_dio_clear_irq(dev); */ 1076 1077 for (group = 0; group < S626_DIO_BANKS; group++) { 1078 irqbit = 0; 1079 /* read interrupt type */ 1080 irqbit = DEBIread(dev, 1081 ((dio_private *) (dev->subdevices + 2 + 1082 group)->private)->RDCapFlg); 1083 1084 /* check if interrupt is generated from dio channels */ 1085 if (irqbit) { 1086 s626_dio_reset_irq(dev, group, irqbit); 1087 DEBUG("s626_irq_handler: check interrupt on dio group %d %d\n", group, i); 1088 if (devpriv->ai_cmd_running) { 1089 /* check if interrupt is an ai acquisition start trigger */ 1090 if ((irqbit >> (cmd->start_arg - 1091 (16 * group))) 1092 == 1 1093 && cmd->start_src == TRIG_EXT) { 1094 DEBUG("s626_irq_handler: Edge capture interrupt recieved from channel %d\n", cmd->start_arg); 1095 1096 /* Start executing the RPS program. */ 1097 MC_ENABLE(P_MC1, MC1_ERPS1); 1098 1099 DEBUG("s626_irq_handler: aquisition start triggered!!!\n"); 1100 1101 if (cmd->scan_begin_src == 1102 TRIG_EXT) { 1103 DEBUG("s626_ai_cmd: enable interrupt on dio channel %d\n", cmd->scan_begin_arg); 1104 1105 s626_dio_set_irq(dev, 1106 cmd-> 1107 scan_begin_arg); 1108 1109 DEBUG("s626_irq_handler: External scan trigger is set!!!\n"); 1110 } 1111 } 1112 if ((irqbit >> (cmd->scan_begin_arg - 1113 (16 * group))) 1114 == 1 1115 && cmd->scan_begin_src == 1116 TRIG_EXT) { 1117 DEBUG("s626_irq_handler: Edge capture interrupt recieved from channel %d\n", cmd->scan_begin_arg); 1118 1119 /* Trigger ADC scan loop start by setting RPS Signal 0. */ 1120 MC_ENABLE(P_MC2, MC2_ADC_RPS); 1121 1122 DEBUG("s626_irq_handler: scan triggered!!! %d\n", devpriv->ai_sample_count); 1123 if (cmd->convert_src == 1124 TRIG_EXT) { 1125 1126 DEBUG("s626_ai_cmd: enable interrupt on dio channel %d group %d\n", cmd->convert_arg - (16 * group), group); 1127 1128 devpriv-> 1129 ai_convert_count 1130 = 1131 cmd-> 1132 chanlist_len; 1133 1134 s626_dio_set_irq(dev, 1135 cmd-> 1136 convert_arg); 1137 1138 DEBUG("s626_irq_handler: External convert trigger is set!!!\n"); 1139 } 1140 1141 if (cmd->convert_src == 1142 TRIG_TIMER) { 1143 k = &encpriv[5]; 1144 devpriv-> 1145 ai_convert_count 1146 = 1147 cmd-> 1148 chanlist_len; 1149 k->SetEnable(dev, k, 1150 CLKENAB_ALWAYS); 1151 } 1152 } 1153 if ((irqbit >> (cmd->convert_arg - 1154 (16 * group))) 1155 == 1 1156 && cmd->convert_src == 1157 TRIG_EXT) { 1158 DEBUG("s626_irq_handler: Edge capture interrupt recieved from channel %d\n", cmd->convert_arg); 1159 1160 /* Trigger ADC scan loop start by setting RPS Signal 0. */ 1161 MC_ENABLE(P_MC2, MC2_ADC_RPS); 1162 1163 DEBUG("s626_irq_handler: adc convert triggered!!!\n"); 1164 1165 devpriv->ai_convert_count--; 1166 1167 if (devpriv->ai_convert_count > 1168 0) { 1169 1170 DEBUG("s626_ai_cmd: enable interrupt on dio channel %d group %d\n", cmd->convert_arg - (16 * group), group); 1171 1172 s626_dio_set_irq(dev, 1173 cmd-> 1174 convert_arg); 1175 1176 DEBUG("s626_irq_handler: External trigger is set!!!\n"); 1177 } 1178 } 1179 } 1180 break; 1181 } 1182 } 1183 1184 /* read interrupt type */ 1185 irqbit = DEBIread(dev, LP_RDMISC2); 1186 1187 /* check interrupt on counters */ 1188 DEBUG("s626_irq_handler: check counters interrupt %d\n", 1189 irqbit); 1190 1191 if (irqbit & IRQ_COINT1A) { 1192 DEBUG("s626_irq_handler: interrupt on counter 1A overflow\n"); 1193 k = &encpriv[0]; 1194 1195 /* clear interrupt capture flag */ 1196 k->ResetCapFlags(dev, k); 1197 } 1198 if (irqbit & IRQ_COINT2A) { 1199 DEBUG("s626_irq_handler: interrupt on counter 2A overflow\n"); 1200 k = &encpriv[1]; 1201 1202 /* clear interrupt capture flag */ 1203 k->ResetCapFlags(dev, k); 1204 } 1205 if (irqbit & IRQ_COINT3A) { 1206 DEBUG("s626_irq_handler: interrupt on counter 3A overflow\n"); 1207 k = &encpriv[2]; 1208 1209 /* clear interrupt capture flag */ 1210 k->ResetCapFlags(dev, k); 1211 } 1212 if (irqbit & IRQ_COINT1B) { 1213 DEBUG("s626_irq_handler: interrupt on counter 1B overflow\n"); 1214 k = &encpriv[3]; 1215 1216 /* clear interrupt capture flag */ 1217 k->ResetCapFlags(dev, k); 1218 } 1219 if (irqbit & IRQ_COINT2B) { 1220 DEBUG("s626_irq_handler: interrupt on counter 2B overflow\n"); 1221 k = &encpriv[4]; 1222 1223 /* clear interrupt capture flag */ 1224 k->ResetCapFlags(dev, k); 1225 1226 if (devpriv->ai_convert_count > 0) { 1227 devpriv->ai_convert_count--; 1228 if (devpriv->ai_convert_count == 0) 1229 k->SetEnable(dev, k, CLKENAB_INDEX); 1230 1231 if (cmd->convert_src == TRIG_TIMER) { 1232 DEBUG("s626_irq_handler: conver timer trigger!!! %d\n", devpriv->ai_convert_count); 1233 1234 /* Trigger ADC scan loop start by setting RPS Signal 0. */ 1235 MC_ENABLE(P_MC2, MC2_ADC_RPS); 1236 } 1237 } 1238 } 1239 if (irqbit & IRQ_COINT3B) { 1240 DEBUG("s626_irq_handler: interrupt on counter 3B overflow\n"); 1241 k = &encpriv[5]; 1242 1243 /* clear interrupt capture flag */ 1244 k->ResetCapFlags(dev, k); 1245 1246 if (cmd->scan_begin_src == TRIG_TIMER) { 1247 DEBUG("s626_irq_handler: scan timer trigger!!!\n"); 1248 1249 /* Trigger ADC scan loop start by setting RPS Signal 0. */ 1250 MC_ENABLE(P_MC2, MC2_ADC_RPS); 1251 } 1252 1253 if (cmd->convert_src == TRIG_TIMER) { 1254 DEBUG("s626_irq_handler: convert timer trigger is set\n"); 1255 k = &encpriv[4]; 1256 devpriv->ai_convert_count = cmd->chanlist_len; 1257 k->SetEnable(dev, k, CLKENAB_ALWAYS); 1258 } 1259 } 1260 } 1261 1262 /* enable interrupt */ 1263 writel(irqstatus, devpriv->base_addr + P_IER); 1264 1265 DEBUG("s626_irq_handler: exit interrupt service routine.\n"); 1266 1267 comedi_spin_unlock_irqrestore(&dev->spinlock, flags); 1268 return IRQ_HANDLED; 1269} 1270 1271static int s626_detach(comedi_device *dev) 1272{ 1273 if (devpriv) { 1274 /* stop ai_command */ 1275 devpriv->ai_cmd_running = 0; 1276 1277 if (devpriv->base_addr) { 1278 /* interrupt mask */ 1279 WR7146(P_IER, 0); /* Disable master interrupt. */ 1280 WR7146(P_ISR, IRQ_GPIO3 | IRQ_RPS1); /* Clear board's IRQ status flag. */ 1281 1282 /* Disable the watchdog timer and battery charger. */ 1283 WriteMISC2(dev, 0); 1284 1285 /* Close all interfaces on 7146 device. */ 1286 WR7146(P_MC1, MC1_SHUTDOWN); 1287 WR7146(P_ACON1, ACON1_BASE); 1288 1289 CloseDMAB(dev, &devpriv->RPSBuf, DMABUF_SIZE); 1290 CloseDMAB(dev, &devpriv->ANABuf, DMABUF_SIZE); 1291 } 1292 1293 if (dev->irq) { 1294 comedi_free_irq(dev->irq, dev); 1295 } 1296 1297 if (devpriv->base_addr) { 1298 iounmap(devpriv->base_addr); 1299 } 1300 1301 if (devpriv->pdev) { 1302 if (devpriv->got_regions) { 1303 comedi_pci_disable(devpriv->pdev); 1304 } 1305 pci_dev_put(devpriv->pdev); 1306 } 1307 } 1308 1309 DEBUG("s626_detach: S626 detached!\n"); 1310 1311 return 0; 1312} 1313 1314/* 1315 * this functions build the RPS program for hardware driven acquistion 1316 */ 1317void ResetADC(comedi_device *dev, uint8_t *ppl) 1318{ 1319 register uint32_t *pRPS; 1320 uint32_t JmpAdrs; 1321 uint16_t i; 1322 uint16_t n; 1323 uint32_t LocalPPL; 1324 comedi_cmd *cmd = &(dev->subdevices->async->cmd); 1325 1326 /* Stop RPS program in case it is currently running. */ 1327 MC_DISABLE(P_MC1, MC1_ERPS1); 1328 1329 /* Set starting logical address to write RPS commands. */ 1330 pRPS = (uint32_t *) devpriv->RPSBuf.LogicalBase; 1331 1332 /* Initialize RPS instruction pointer. */ 1333 WR7146(P_RPSADDR1, (uint32_t) devpriv->RPSBuf.PhysicalBase); 1334 1335 /* Construct RPS program in RPSBuf DMA buffer */ 1336 1337 if (cmd != NULL && cmd->scan_begin_src != TRIG_FOLLOW) { 1338 DEBUG("ResetADC: scan_begin pause inserted\n"); 1339 /* Wait for Start trigger. */ 1340 *pRPS++ = RPS_PAUSE | RPS_SIGADC; 1341 *pRPS++ = RPS_CLRSIGNAL | RPS_SIGADC; 1342 } 1343 1344 /* SAA7146 BUG WORKAROUND Do a dummy DEBI Write. This is necessary 1345 * because the first RPS DEBI Write following a non-RPS DEBI write 1346 * seems to always fail. If we don't do this dummy write, the ADC 1347 * gain might not be set to the value required for the first slot in 1348 * the poll list; the ADC gain would instead remain unchanged from 1349 * the previously programmed value. 1350 */ 1351 *pRPS++ = RPS_LDREG | (P_DEBICMD >> 2); 1352 /* Write DEBI Write command and address to shadow RAM. */ 1353 1354 *pRPS++ = DEBI_CMD_WRWORD | LP_GSEL; 1355 *pRPS++ = RPS_LDREG | (P_DEBIAD >> 2); 1356 /* Write DEBI immediate data to shadow RAM: */ 1357 1358 *pRPS++ = GSEL_BIPOLAR5V; 1359 /* arbitrary immediate data value. */ 1360 1361 *pRPS++ = RPS_CLRSIGNAL | RPS_DEBI; 1362 /* Reset "shadow RAM uploaded" flag. */ 1363 *pRPS++ = RPS_UPLOAD | RPS_DEBI; /* Invoke shadow RAM upload. */ 1364 *pRPS++ = RPS_PAUSE | RPS_DEBI; /* Wait for shadow upload to finish. */ 1365 1366 /* Digitize all slots in the poll list. This is implemented as a 1367 * for loop to limit the slot count to 16 in case the application 1368 * forgot to set the EOPL flag in the final slot. 1369 */ 1370 for (devpriv->AdcItems = 0; devpriv->AdcItems < 16; devpriv->AdcItems++) { 1371 /* Convert application's poll list item to private board class 1372 * format. Each app poll list item is an uint8_t with form 1373 * (EOPL,x,x,RANGE,CHAN<3:0>), where RANGE code indicates 0 = 1374 * +-10V, 1 = +-5V, and EOPL = End of Poll List marker. 1375 */ 1376 LocalPPL = 1377 (*ppl << 8) | (*ppl & 0x10 ? GSEL_BIPOLAR5V : 1378 GSEL_BIPOLAR10V); 1379 1380 /* Switch ADC analog gain. */ 1381 *pRPS++ = RPS_LDREG | (P_DEBICMD >> 2); /* Write DEBI command */ 1382 /* and address to */ 1383 /* shadow RAM. */ 1384 *pRPS++ = DEBI_CMD_WRWORD | LP_GSEL; 1385 *pRPS++ = RPS_LDREG | (P_DEBIAD >> 2); /* Write DEBI */ 1386 /* immediate data to */ 1387 /* shadow RAM. */ 1388 *pRPS++ = LocalPPL; 1389 *pRPS++ = RPS_CLRSIGNAL | RPS_DEBI; /* Reset "shadow RAM uploaded" */ 1390 /* flag. */ 1391 *pRPS++ = RPS_UPLOAD | RPS_DEBI; /* Invoke shadow RAM upload. */ 1392 *pRPS++ = RPS_PAUSE | RPS_DEBI; /* Wait for shadow upload to */ 1393 /* finish. */ 1394 1395 /* Select ADC analog input channel. */ 1396 *pRPS++ = RPS_LDREG | (P_DEBICMD >> 2); 1397 /* Write DEBI command and address to shadow RAM. */ 1398 *pRPS++ = DEBI_CMD_WRWORD | LP_ISEL; 1399 *pRPS++ = RPS_LDREG | (P_DEBIAD >> 2); 1400 /* Write DEBI immediate data to shadow RAM. */ 1401 *pRPS++ = LocalPPL; 1402 *pRPS++ = RPS_CLRSIGNAL | RPS_DEBI; 1403 /* Reset "shadow RAM uploaded" flag. */ 1404 1405 *pRPS++ = RPS_UPLOAD | RPS_DEBI; 1406 /* Invoke shadow RAM upload. */ 1407 1408 *pRPS++ = RPS_PAUSE | RPS_DEBI; 1409 /* Wait for shadow upload to finish. */ 1410 1411 /* Delay at least 10 microseconds for analog input settling. 1412 * Instead of padding with NOPs, we use RPS_JUMP instructions 1413 * here; this allows us to produce a longer delay than is 1414 * possible with NOPs because each RPS_JUMP flushes the RPS' 1415 * instruction prefetch pipeline. 1416 */ 1417 JmpAdrs = 1418 (uint32_t) devpriv->RPSBuf.PhysicalBase + 1419 (uint32_t) ((unsigned long)pRPS - 1420 (unsigned long)devpriv->RPSBuf.LogicalBase); 1421 for (i = 0; i < (10 * RPSCLK_PER_US / 2); i++) { 1422 JmpAdrs += 8; /* Repeat to implement time delay: */ 1423 *pRPS++ = RPS_JUMP; /* Jump to next RPS instruction. */ 1424 *pRPS++ = JmpAdrs; 1425 } 1426 1427 if (cmd != NULL && cmd->convert_src != TRIG_NOW) { 1428 DEBUG("ResetADC: convert pause inserted\n"); 1429 /* Wait for Start trigger. */ 1430 *pRPS++ = RPS_PAUSE | RPS_SIGADC; 1431 *pRPS++ = RPS_CLRSIGNAL | RPS_SIGADC; 1432 } 1433 /* Start ADC by pulsing GPIO1. */ 1434 *pRPS++ = RPS_LDREG | (P_GPIO >> 2); /* Begin ADC Start pulse. */ 1435 *pRPS++ = GPIO_BASE | GPIO1_LO; 1436 *pRPS++ = RPS_NOP; 1437 /* VERSION 2.03 CHANGE: STRETCH OUT ADC START PULSE. */ 1438 *pRPS++ = RPS_LDREG | (P_GPIO >> 2); /* End ADC Start pulse. */ 1439 *pRPS++ = GPIO_BASE | GPIO1_HI; 1440 1441 /* Wait for ADC to complete (GPIO2 is asserted high when ADC not 1442 * busy) and for data from previous conversion to shift into FB 1443 * BUFFER 1 register. 1444 */ 1445 *pRPS++ = RPS_PAUSE | RPS_GPIO2; /* Wait for ADC done. */ 1446 1447 /* Transfer ADC data from FB BUFFER 1 register to DMA buffer. */ 1448 *pRPS++ = RPS_STREG | (BUGFIX_STREG(P_FB_BUFFER1) >> 2); 1449 *pRPS++ = 1450 (uint32_t) devpriv->ANABuf.PhysicalBase + 1451 (devpriv->AdcItems << 2); 1452 1453 /* If this slot's EndOfPollList flag is set, all channels have */ 1454 /* now been processed. */ 1455 if (*ppl++ & EOPL) { 1456 devpriv->AdcItems++; /* Adjust poll list item count. */ 1457 break; /* Exit poll list processing loop. */ 1458 } 1459 } 1460 DEBUG("ResetADC: ADC items %d \n", devpriv->AdcItems); 1461 1462 /* VERSION 2.01 CHANGE: DELAY CHANGED FROM 250NS to 2US. Allow the 1463 * ADC to stabilize for 2 microseconds before starting the final 1464 * (dummy) conversion. This delay is necessary to allow sufficient 1465 * time between last conversion finished and the start of the dummy 1466 * conversion. Without this delay, the last conversion's data value 1467 * is sometimes set to the previous conversion's data value. 1468 */ 1469 for (n = 0; n < (2 * RPSCLK_PER_US); n++) 1470 *pRPS++ = RPS_NOP; 1471 1472 /* Start a dummy conversion to cause the data from the last 1473 * conversion of interest to be shifted in. 1474 */ 1475 *pRPS++ = RPS_LDREG | (P_GPIO >> 2); /* Begin ADC Start pulse. */ 1476 *pRPS++ = GPIO_BASE | GPIO1_LO; 1477 *pRPS++ = RPS_NOP; 1478 /* VERSION 2.03 CHANGE: STRETCH OUT ADC START PULSE. */ 1479 *pRPS++ = RPS_LDREG | (P_GPIO >> 2); /* End ADC Start pulse. */ 1480 *pRPS++ = GPIO_BASE | GPIO1_HI; 1481 1482 /* Wait for the data from the last conversion of interest to arrive 1483 * in FB BUFFER 1 register. 1484 */ 1485 *pRPS++ = RPS_PAUSE | RPS_GPIO2; /* Wait for ADC done. */ 1486 1487 /* Transfer final ADC data from FB BUFFER 1 register to DMA buffer. */ 1488 *pRPS++ = RPS_STREG | (BUGFIX_STREG(P_FB_BUFFER1) >> 2); /* */ 1489 *pRPS++ = 1490 (uint32_t) devpriv->ANABuf.PhysicalBase + 1491 (devpriv->AdcItems << 2); 1492 1493 /* Indicate ADC scan loop is finished. */ 1494 /* *pRPS++= RPS_CLRSIGNAL | RPS_SIGADC ; // Signal ReadADC() that scan is done. */ 1495 1496 /* invoke interrupt */ 1497 if (devpriv->ai_cmd_running == 1) { 1498 DEBUG("ResetADC: insert irq in ADC RPS task\n"); 1499 *pRPS++ = RPS_IRQ; 1500 } 1501 /* Restart RPS program at its beginning. */ 1502 *pRPS++ = RPS_JUMP; /* Branch to start of RPS program. */ 1503 *pRPS++ = (uint32_t) devpriv->RPSBuf.PhysicalBase; 1504 1505 /* End of RPS program build */ 1506} 1507 1508/* TO COMPLETE, IF NECESSARY */ 1509static int s626_ai_insn_config(comedi_device *dev, comedi_subdevice *s, 1510 comedi_insn *insn, lsampl_t *data) 1511{ 1512 1513 return -EINVAL; 1514} 1515 1516/* static int s626_ai_rinsn(comedi_device *dev,comedi_subdevice *s,comedi_insn *insn,lsampl_t *data) */ 1517/* { */ 1518/* register uint8_t i; */ 1519/* register int32_t *readaddr; */ 1520 1521/* DEBUG("as626_ai_rinsn: ai_rinsn enter \n"); */ 1522 1523/* Trigger ADC scan loop start by setting RPS Signal 0. */ 1524/* MC_ENABLE( P_MC2, MC2_ADC_RPS ); */ 1525 1526/* Wait until ADC scan loop is finished (RPS Signal 0 reset). */ 1527/* while ( MC_TEST( P_MC2, MC2_ADC_RPS ) ); */ 1528 1529/* Init ptr to DMA buffer that holds new ADC data. We skip the 1530 * first uint16_t in the buffer because it contains junk data from 1531 * the final ADC of the previous poll list scan. 1532 */ 1533/* readaddr = (uint32_t *)devpriv->ANABuf.LogicalBase + 1; */ 1534 1535/* Convert ADC data to 16-bit integer values and copy to application buffer. */ 1536/* for ( i = 0; i < devpriv->AdcItems; i++ ) { */ 1537/* *data = s626_ai_reg_to_uint( *readaddr++ ); */ 1538/* DEBUG("s626_ai_rinsn: data %d \n",*data); */ 1539/* data++; */ 1540/* } */ 1541 1542/* DEBUG("s626_ai_rinsn: ai_rinsn escape \n"); */ 1543/* return i; */ 1544/* } */ 1545 1546static int s626_ai_insn_read(comedi_device *dev, comedi_subdevice *s, 1547 comedi_insn *insn, lsampl_t *data) 1548{ 1549 uint16_t chan = CR_CHAN(insn->chanspec); 1550 uint16_t range = CR_RANGE(insn->chanspec); 1551 uint16_t AdcSpec = 0; 1552 uint32_t GpioImage; 1553 int n; 1554 1555 /* interrupt call test */ 1556/* writel(IRQ_GPIO3,devpriv->base_addr+P_PSR); */ 1557 /* Writing a logical 1 into any of the RPS_PSR bits causes the 1558 * corresponding interrupt to be generated if enabled 1559 */ 1560 1561 DEBUG("s626_ai_insn_read: entering\n"); 1562 1563 /* Convert application's ADC specification into form 1564 * appropriate for register programming. 1565 */ 1566 if (range == 0) 1567 AdcSpec = (chan << 8) | (GSEL_BIPOLAR5V); 1568 else 1569 AdcSpec = (chan << 8) | (GSEL_BIPOLAR10V); 1570 1571 /* Switch ADC analog gain. */ 1572 DEBIwrite(dev, LP_GSEL, AdcSpec); /* Set gain. */ 1573 1574 /* Select ADC analog input channel. */ 1575 DEBIwrite(dev, LP_ISEL, AdcSpec); /* Select channel. */ 1576 1577 for (n = 0; n < insn->n; n++) { 1578 1579 /* Delay 10 microseconds for analog input settling. */ 1580 comedi_udelay(10); 1581 1582 /* Start ADC by pulsing GPIO1 low. */ 1583 GpioImage = RR7146(P_GPIO); 1584 /* Assert ADC Start command */ 1585 WR7146(P_GPIO, GpioImage & ~GPIO1_HI); 1586 /* and stretch it out. */ 1587 WR7146(P_GPIO, GpioImage & ~GPIO1_HI); 1588 WR7146(P_GPIO, GpioImage & ~GPIO1_HI); 1589 /* Negate ADC Start command. */ 1590 WR7146(P_GPIO, GpioImage | GPIO1_HI); 1591 1592 /* Wait for ADC to complete (GPIO2 is asserted high when */ 1593 /* ADC not busy) and for data from previous conversion to */ 1594 /* shift into FB BUFFER 1 register. */ 1595 1596 /* Wait for ADC done. */ 1597 while (!(RR7146(P_PSR) & PSR_GPIO2)) 1598 ; 1599 1600 /* Fetch ADC data. */ 1601 if (n != 0) 1602 data[n - 1] = s626_ai_reg_to_uint(RR7146(P_FB_BUFFER1)); 1603 1604 /* Allow the ADC to stabilize for 4 microseconds before 1605 * starting the next (final) conversion. This delay is 1606 * necessary to allow sufficient time between last 1607 * conversion finished and the start of the next 1608 * conversion. Without this delay, the last conversion's 1609 * data value is sometimes set to the previous 1610 * conversion's data value. 1611 */ 1612 comedi_udelay(4); 1613 } 1614 1615 /* Start a dummy conversion to cause the data from the 1616 * previous conversion to be shifted in. */ 1617 GpioImage = RR7146(P_GPIO); 1618 1619 /* Assert ADC Start command */ 1620 WR7146(P_GPIO, GpioImage & ~GPIO1_HI); 1621 /* and stretch it out. */ 1622 WR7146(P_GPIO, GpioImage & ~GPIO1_HI); 1623 WR7146(P_GPIO, GpioImage & ~GPIO1_HI); 1624 /* Negate ADC Start command. */ 1625 WR7146(P_GPIO, GpioImage | GPIO1_HI); 1626 1627 /* Wait for the data to arrive in FB BUFFER 1 register. */ 1628 1629 /* Wait for ADC done. */ 1630 while (!(RR7146(P_PSR) & PSR_GPIO2)) 1631 ; 1632 1633 /* Fetch ADC data from audio interface's input shift register. */ 1634 1635 /* Fetch ADC data. */ 1636 if (n != 0) 1637 data[n - 1] = s626_ai_reg_to_uint(RR7146(P_FB_BUFFER1)); 1638 1639 DEBUG("s626_ai_insn_read: samples %d, data %d\n", n, data[n - 1]); 1640 1641 return n; 1642} 1643 1644static int s626_ai_load_polllist(uint8_t *ppl, comedi_cmd *cmd) 1645{ 1646 1647 int n; 1648 1649 for (n = 0; n < cmd->chanlist_len; n++) { 1650 if (CR_RANGE((cmd->chanlist)[n]) == 0) 1651 ppl[n] = (CR_CHAN((cmd->chanlist)[n])) | (RANGE_5V); 1652 else 1653 ppl[n] = (CR_CHAN((cmd->chanlist)[n])) | (RANGE_10V); 1654 } 1655 ppl[n - 1] |= EOPL; 1656 1657 return n; 1658} 1659 1660static int s626_ai_inttrig(comedi_device *dev, comedi_subdevice *s, 1661 unsigned int trignum) 1662{ 1663 if (trignum != 0) 1664 return -EINVAL; 1665 1666 DEBUG("s626_ai_inttrig: trigger adc start..."); 1667 1668 /* Start executing the RPS program. */ 1669 MC_ENABLE(P_MC1, MC1_ERPS1); 1670 1671 s->async->inttrig = NULL; 1672 1673 DEBUG(" done\n"); 1674 1675 return 1; 1676} 1677 1678/* TO COMPLETE */ 1679static int s626_ai_cmd(comedi_device *dev, comedi_subdevice *s) 1680{ 1681 1682 uint8_t ppl[16]; 1683 comedi_cmd *cmd = &s->async->cmd; 1684 enc_private *k; 1685 int tick; 1686 1687 DEBUG("s626_ai_cmd: entering command function\n"); 1688 1689 if (devpriv->ai_cmd_running) { 1690 printk("s626_ai_cmd: Another ai_cmd is running %d\n", 1691 dev->minor); 1692 return -EBUSY; 1693 } 1694 /* disable interrupt */ 1695 writel(0, devpriv->base_addr + P_IER); 1696 1697 /* clear interrupt request */ 1698 writel(IRQ_RPS1 | IRQ_GPIO3, devpriv->base_addr + P_ISR); 1699 1700 /* clear any pending interrupt */ 1701 s626_dio_clear_irq(dev); 1702 /* s626_enc_clear_irq(dev); */ 1703 1704 /* reset ai_cmd_running flag */ 1705 devpriv->ai_cmd_running = 0; 1706 1707 /* test if cmd is valid */ 1708 if (cmd == NULL) { 1709 DEBUG("s626_ai_cmd: NULL command\n"); 1710 return -EINVAL; 1711 } else { 1712 DEBUG("s626_ai_cmd: command recieved!!!\n"); 1713 } 1714 1715 if (dev->irq == 0) { 1716 comedi_error(dev, 1717 "s626_ai_cmd: cannot run command without an irq"); 1718 return -EIO; 1719 } 1720 1721 s626_ai_load_polllist(ppl, cmd); 1722 devpriv->ai_cmd_running = 1; 1723 devpriv->ai_convert_count = 0; 1724 1725 switch (cmd->scan_begin_src) { 1726 case TRIG_FOLLOW: 1727 break; 1728 case TRIG_TIMER: 1729 /* set a conter to generate adc trigger at scan_begin_arg interval */ 1730 k = &encpriv[5]; 1731 tick = s626_ns_to_timer((int *)&cmd->scan_begin_arg, 1732 cmd->flags & TRIG_ROUND_MASK); 1733 1734 /* load timer value and enable interrupt */ 1735 s626_timer_load(dev, k, tick); 1736 k->SetEnable(dev, k, CLKENAB_ALWAYS); 1737 1738 DEBUG("s626_ai_cmd: scan trigger timer is set with value %d\n", 1739 tick); 1740 1741 break; 1742 case TRIG_EXT: 1743 /* set the digital line and interrupt for scan trigger */ 1744 if (cmd->start_src != TRIG_EXT) 1745 s626_dio_set_irq(dev, cmd->scan_begin_arg); 1746 1747 DEBUG("s626_ai_cmd: External scan trigger is set!!!\n"); 1748 1749 break; 1750 } 1751 1752 switch (cmd->convert_src) { 1753 case TRIG_NOW: 1754 break; 1755 case TRIG_TIMER: 1756 /* set a conter to generate adc trigger at convert_arg interval */ 1757 k = &encpriv[4]; 1758 tick = s626_ns_to_timer((int *)&cmd->convert_arg, 1759 cmd->flags & TRIG_ROUND_MASK); 1760 1761 /* load timer value and enable interrupt */ 1762 s626_timer_load(dev, k, tick); 1763 k->SetEnable(dev, k, CLKENAB_INDEX); 1764 1765 DEBUG("s626_ai_cmd: convert trigger timer is set with value %d\n", tick); 1766 break; 1767 case TRIG_EXT: 1768 /* set the digital line and interrupt for convert trigger */ 1769 if (cmd->scan_begin_src != TRIG_EXT 1770 && cmd->start_src == TRIG_EXT) 1771 s626_dio_set_irq(dev, cmd->convert_arg); 1772 1773 DEBUG("s626_ai_cmd: External convert trigger is set!!!\n"); 1774 1775 break; 1776 } 1777 1778 switch (cmd->stop_src) { 1779 case TRIG_COUNT: 1780 /* data arrives as one packet */ 1781 devpriv->ai_sample_count = cmd->stop_arg; 1782 devpriv->ai_continous = 0; 1783 break; 1784 case TRIG_NONE: 1785 /* continous aquisition */ 1786 devpriv->ai_continous = 1; 1787 devpriv->ai_sample_count = 0; 1788 break; 1789 } 1790 1791 ResetADC(dev, ppl); 1792 1793 switch (cmd->start_src) { 1794 case TRIG_NOW: 1795 /* Trigger ADC scan loop start by setting RPS Signal 0. */ 1796 /* MC_ENABLE( P_MC2, MC2_ADC_RPS ); */ 1797 1798 /* Start executing the RPS program. */ 1799 MC_ENABLE(P_MC1, MC1_ERPS1); 1800 1801 DEBUG("s626_ai_cmd: ADC triggered\n"); 1802 s->async->inttrig = NULL; 1803 break; 1804 case TRIG_EXT: 1805 /* configure DIO channel for acquisition trigger */ 1806 s626_dio_set_irq(dev, cmd->start_arg); 1807 1808 DEBUG("s626_ai_cmd: External start trigger is set!!!\n"); 1809 1810 s->async->inttrig = NULL; 1811 break; 1812 case TRIG_INT: 1813 s->async->inttrig = s626_ai_inttrig; 1814 break; 1815 } 1816 1817 /* enable interrupt */ 1818 writel(IRQ_GPIO3 | IRQ_RPS1, devpriv->base_addr + P_IER); 1819 1820 DEBUG("s626_ai_cmd: command function terminated\n"); 1821 1822 return 0; 1823} 1824 1825static int s626_ai_cmdtest(comedi_device *dev, comedi_subdevice *s, 1826 comedi_cmd *cmd) 1827{ 1828 int err = 0; 1829 int tmp; 1830 1831 /* cmdtest tests a particular command to see if it is valid. Using 1832 * the cmdtest ioctl, a user can create a valid cmd and then have it 1833 * executes by the cmd ioctl. 1834 * 1835 * cmdtest returns 1,2,3,4 or 0, depending on which tests the 1836 * command passes. */ 1837 1838 /* step 1: make sure trigger sources are trivially valid */ 1839 1840 tmp = cmd->start_src; 1841 cmd->start_src &= TRIG_NOW | TRIG_INT | TRIG_EXT; 1842 if (!cmd->start_src || tmp != cmd->start_src) 1843 err++; 1844 1845 tmp = cmd->scan_begin_src; 1846 cmd->scan_begin_src &= TRIG_TIMER | TRIG_EXT | TRIG_FOLLOW; 1847 if (!cmd->scan_begin_src || tmp != cmd->scan_begin_src) 1848 err++; 1849 1850 tmp = cmd->convert_src; 1851 cmd->convert_src &= TRIG_TIMER | TRIG_EXT | TRIG_NOW; 1852 if (!cmd->convert_src || tmp != cmd->convert_src) 1853 err++; 1854 1855 tmp = cmd->scan_end_src; 1856 cmd->scan_end_src &= TRIG_COUNT; 1857 if (!cmd->scan_end_src || tmp != cmd->scan_end_src) 1858 err++; 1859 1860 tmp = cmd->stop_src; 1861 cmd->stop_src &= TRIG_COUNT | TRIG_NONE; 1862 if (!cmd->stop_src || tmp != cmd->stop_src) 1863 err++; 1864 1865 if (err) 1866 return 1; 1867 1868 /* step 2: make sure trigger sources are unique and mutually 1869 compatible */ 1870 1871 /* note that mutual compatiblity is not an issue here */ 1872 if (cmd->scan_begin_src != TRIG_TIMER && 1873 cmd->scan_begin_src != TRIG_EXT 1874 && cmd->scan_begin_src != TRIG_FOLLOW) 1875 err++; 1876 if (cmd->convert_src != TRIG_TIMER && 1877 cmd->convert_src != TRIG_EXT && cmd->convert_src != TRIG_NOW) 1878 err++; 1879 if (cmd->stop_src != TRIG_COUNT && cmd->stop_src != TRIG_NONE) 1880 err++; 1881 1882 if (err) 1883 return 2; 1884 1885 /* step 3: make sure arguments are trivially compatible */ 1886 1887 if (cmd->start_src != TRIG_EXT && cmd->start_arg != 0) { 1888 cmd->start_arg = 0; 1889 err++; 1890 } 1891 1892 if (cmd->start_src == TRIG_EXT && cmd->start_arg < 0) { 1893 cmd->start_arg = 0; 1894 err++; 1895 } 1896 1897 if (cmd->start_src == TRIG_EXT && cmd->start_arg > 39) { 1898 cmd->start_arg = 39; 1899 err++; 1900 } 1901 1902 if (cmd->scan_begin_src == TRIG_EXT && cmd->scan_begin_arg < 0) { 1903 cmd->scan_begin_arg = 0; 1904 err++; 1905 } 1906 1907 if (cmd->scan_begin_src == TRIG_EXT && cmd->scan_begin_arg > 39) { 1908 cmd->scan_begin_arg = 39; 1909 err++; 1910 } 1911 1912 if (cmd->convert_src == TRIG_EXT && cmd->convert_arg < 0) { 1913 cmd->convert_arg = 0; 1914 err++; 1915 } 1916 1917 if (cmd->convert_src == TRIG_EXT && cmd->convert_arg > 39) { 1918 cmd->convert_arg = 39; 1919 err++; 1920 } 1921#define MAX_SPEED 200000 /* in nanoseconds */ 1922#define MIN_SPEED 2000000000 /* in nanoseconds */ 1923 1924 if (cmd->scan_begin_src == TRIG_TIMER) { 1925 if (cmd->scan_begin_arg < MAX_SPEED) { 1926 cmd->scan_begin_arg = MAX_SPEED; 1927 err++; 1928 } 1929 if (cmd->scan_begin_arg > MIN_SPEED) { 1930 cmd->scan_begin_arg = MIN_SPEED; 1931 err++; 1932 } 1933 } else { 1934 /* external trigger */ 1935 /* should be level/edge, hi/lo specification here */ 1936 /* should specify multiple external triggers */ 1937/* if(cmd->scan_begin_arg>9){ */ 1938/* cmd->scan_begin_arg=9; */ 1939/* err++; */ 1940/* } */ 1941 } 1942 if (cmd->convert_src == TRIG_TIMER) { 1943 if (cmd->convert_arg < MAX_SPEED) { 1944 cmd->convert_arg = MAX_SPEED; 1945 err++; 1946 } 1947 if (cmd->convert_arg > MIN_SPEED) { 1948 cmd->convert_arg = MIN_SPEED; 1949 err++; 1950 } 1951 } else { 1952 /* external trigger */ 1953 /* see above */ 1954/* if(cmd->convert_arg>9){ */ 1955/* cmd->convert_arg=9; */ 1956/* err++; */ 1957/* } */ 1958 } 1959 1960 if (cmd->scan_end_arg != cmd->chanlist_len) { 1961 cmd->scan_end_arg = cmd->chanlist_len; 1962 err++; 1963 } 1964 if (cmd->stop_src == TRIG_COUNT) { 1965 if (cmd->stop_arg > 0x00ffffff) { 1966 cmd->stop_arg = 0x00ffffff; 1967 err++; 1968 } 1969 } else { 1970 /* TRIG_NONE */ 1971 if (cmd->stop_arg != 0) { 1972 cmd->stop_arg = 0; 1973 err++; 1974 } 1975 } 1976 1977 if (err) 1978 return 3; 1979 1980 /* step 4: fix up any arguments */ 1981 1982 if (cmd->scan_begin_src == TRIG_TIMER) { 1983 tmp = cmd->scan_begin_arg; 1984 s626_ns_to_timer((int *)&cmd->scan_begin_arg, 1985 cmd->flags & TRIG_ROUND_MASK); 1986 if (tmp != cmd->scan_begin_arg) 1987 err++; 1988 } 1989 if (cmd->convert_src == TRIG_TIMER) { 1990 tmp = cmd->convert_arg; 1991 s626_ns_to_timer((int *)&cmd->convert_arg, 1992 cmd->flags & TRIG_ROUND_MASK); 1993 if (tmp != cmd->convert_arg) 1994 err++; 1995 if (cmd->scan_begin_src == TRIG_TIMER && 1996 cmd->scan_begin_arg < 1997 cmd->convert_arg * cmd->scan_end_arg) { 1998 cmd->scan_begin_arg = 1999 cmd->convert_arg * cmd->scan_end_arg; 2000 err++; 2001 } 2002 } 2003 2004 if (err) 2005 return 4; 2006 2007 return 0; 2008} 2009 2010static int s626_ai_cancel(comedi_device *dev, comedi_subdevice *s) 2011{ 2012 /* Stop RPS program in case it is currently running. */ 2013 MC_DISABLE(P_MC1, MC1_ERPS1); 2014 2015 /* disable master interrupt */ 2016 writel(0, devpriv->base_addr + P_IER); 2017 2018 devpriv->ai_cmd_running = 0; 2019 2020 return 0; 2021} 2022 2023/* This function doesn't require a particular form, this is just what 2024 * happens to be used in some of the drivers. It should convert ns 2025 * nanoseconds to a counter value suitable for programming the device. 2026 * Also, it should adjust ns so that it cooresponds to the actual time 2027 * that the device will use. */ 2028static int s626_ns_to_timer(int *nanosec, int round_mode) 2029{ 2030 int divider, base; 2031 2032 base = 500; /* 2MHz internal clock */ 2033 2034 switch (round_mode) { 2035 case TRIG_ROUND_NEAREST: 2036 default: 2037 divider = (*nanosec + base / 2) / base; 2038 break; 2039 case TRIG_ROUND_DOWN: 2040 divider = (*nanosec) / base; 2041 break; 2042 case TRIG_ROUND_UP: 2043 divider = (*nanosec + base - 1) / base; 2044 break; 2045 } 2046 2047 *nanosec = base * divider; 2048 return divider - 1; 2049} 2050 2051static int s626_ao_winsn(comedi_device *dev, comedi_subdevice *s, 2052 comedi_insn *insn, lsampl_t *data) 2053{ 2054 2055 int i; 2056 uint16_t chan = CR_CHAN(insn->chanspec); 2057 int16_t dacdata; 2058 2059 for (i = 0; i < insn->n; i++) { 2060 dacdata = (int16_t) data[i]; 2061 devpriv->ao_readback[CR_CHAN(insn->chanspec)] = data[i]; 2062 dacdata -= (0x1fff); 2063 2064 SetDAC(dev, chan, dacdata); 2065 } 2066 2067 return i; 2068} 2069 2070static int s626_ao_rinsn(comedi_device *dev, comedi_subdevice *s, 2071 comedi_insn *insn, lsampl_t *data) 2072{ 2073 int i; 2074 2075 for (i = 0; i < insn->n; i++) { 2076 data[i] = devpriv->ao_readback[CR_CHAN(insn->chanspec)]; 2077 } 2078 2079 return i; 2080} 2081 2082/* *************** DIGITAL I/O FUNCTIONS *************** 2083 * All DIO functions address a group of DIO channels by means of 2084 * "group" argument. group may be 0, 1 or 2, which correspond to DIO 2085 * ports A, B and C, respectively. 2086 */ 2087 2088static void s626_dio_init(comedi_device *dev) 2089{ 2090 uint16_t group; 2091 comedi_subdevice *s; 2092 2093 /* Prepare to treat writes to WRCapSel as capture disables. */ 2094 DEBIwrite(dev, LP_MISC1, MISC1_NOEDCAP); 2095 2096 /* For each group of sixteen channels ... */ 2097 for (group = 0; group < S626_DIO_BANKS; group++) { 2098 s = dev->subdevices + 2 + group; 2099 DEBIwrite(dev, diopriv->WRIntSel, 0); /* Disable all interrupts. */ 2100 DEBIwrite(dev, diopriv->WRCapSel, 0xFFFF); /* Disable all event */ 2101 /* captures. */ 2102 DEBIwrite(dev, diopriv->WREdgSel, 0); /* Init all DIOs to */ 2103 /* default edge */ 2104 /* polarity. */ 2105 DEBIwrite(dev, diopriv->WRDOut, 0); /* Program all outputs */ 2106 /* to inactive state. */ 2107 } 2108 DEBUG("s626_dio_init: DIO initialized \n"); 2109} 2110 2111/* DIO devices are slightly special. Although it is possible to 2112 * implement the insn_read/insn_write interface, it is much more 2113 * useful to applications if you implement the insn_bits interface. 2114 * This allows packed reading/writing of the DIO channels. The comedi 2115 * core can convert between insn_bits and insn_read/write */ 2116 2117static int s626_dio_insn_bits(comedi_device *dev, comedi_subdevice *s, 2118 comedi_insn *insn, lsampl_t *data) 2119{ 2120 2121 /* Length of data must be 2 (mask and new data, see below) */ 2122 if (insn->n == 0) { 2123 return 0; 2124 } 2125 if (insn->n != 2) { 2126 printk("comedi%d: s626: s626_dio_insn_bits(): Invalid instruction length\n", dev->minor); 2127 return -EINVAL; 2128 } 2129 2130 /* 2131 * The insn data consists of a mask in data[0] and the new data in 2132 * data[1]. The mask defines which bits we are concerning about. 2133 * The new data must be anded with the mask. Each channel 2134 * corresponds to a bit. 2135 */ 2136 if (data[0]) { 2137 /* Check if requested ports are configured for output */ 2138 if ((s->io_bits & data[0]) != data[0]) 2139 return -EIO; 2140 2141 s->state &= ~data[0]; 2142 s->state |= data[0] & data[1]; 2143 2144 /* Write out the new digital output lines */ 2145 2146 DEBIwrite(dev, diopriv->WRDOut, s->state); 2147 } 2148 data[1] = DEBIread(dev, diopriv->RDDIn); 2149 2150 return 2; 2151} 2152 2153static int s626_dio_insn_config(comedi_device *dev, comedi_subdevice *s, 2154 comedi_insn *insn, lsampl_t *data) 2155{ 2156 2157 switch (data[0]) { 2158 case INSN_CONFIG_DIO_QUERY: 2159 data[1] = 2160 (s->io_bits & (1 << CR_CHAN(insn-> 2161 chanspec))) ? COMEDI_OUTPUT : 2162 COMEDI_INPUT; 2163 return insn->n; 2164 break; 2165 case COMEDI_INPUT: 2166 s->io_bits &= ~(1 << CR_CHAN(insn->chanspec)); 2167 break; 2168 case COMEDI_OUTPUT: 2169 s->io_bits |= 1 << CR_CHAN(insn->chanspec); 2170 break; 2171 default: 2172 return -EINVAL; 2173 break; 2174 } 2175 DEBIwrite(dev, diopriv->WRDOut, s->io_bits); 2176 2177 return 1; 2178} 2179 2180static int s626_dio_set_irq(comedi_device *dev, unsigned int chan) 2181{ 2182 unsigned int group; 2183 unsigned int bitmask; 2184 unsigned int status; 2185 2186 /* select dio bank */ 2187 group = chan / 16; 2188 bitmask = 1 << (chan - (16 * group)); 2189 DEBUG("s626_dio_set_irq: enable interrupt on dio channel %d group %d\n", 2190 chan - (16 * group), group); 2191 2192 /* set channel to capture positive edge */ 2193 status = DEBIread(dev, 2194 ((dio_private *) (dev->subdevices + 2 + 2195 group)->private)->RDEdgSel); 2196 DEBIwrite(dev, 2197 ((dio_private *) (dev->subdevices + 2 + 2198 group)->private)->WREdgSel, bitmask | status); 2199 2200 /* enable interrupt on selected channel */ 2201 status = DEBIread(dev, 2202 ((dio_private *) (dev->subdevices + 2 + 2203 group)->private)->RDIntSel); 2204 DEBIwrite(dev, 2205 ((dio_private *) (dev->subdevices + 2 + 2206 group)->private)->WRIntSel, bitmask | status); 2207 2208 /* enable edge capture write command */ 2209 DEBIwrite(dev, LP_MISC1, MISC1_EDCAP); 2210 2211 /* enable edge capture on selected channel */ 2212 status = DEBIread(dev, 2213 ((dio_private *) (dev->subdevices + 2 + 2214 group)->private)->RDCapSel); 2215 DEBIwrite(dev, 2216 ((dio_private *) (dev->subdevices + 2 + 2217 group)->private)->WRCapSel, bitmask | status); 2218 2219 return 0; 2220} 2221 2222static int s626_dio_reset_irq(comedi_device *dev, unsigned int group, 2223 unsigned int mask) 2224{ 2225 DEBUG("s626_dio_reset_irq: disable interrupt on dio channel %d group %d\n", mask, group); 2226 2227 /* disable edge capture write command */ 2228 DEBIwrite(dev, LP_MISC1, MISC1_NOEDCAP); 2229 2230 /* enable edge capture on selected channel */ 2231 DEBIwrite(dev, 2232 ((dio_private *) (dev->subdevices + 2 + 2233 group)->private)->WRCapSel, mask); 2234 2235 return 0; 2236} 2237 2238static int s626_dio_clear_irq(comedi_device *dev) 2239{ 2240 unsigned int group; 2241 2242 /* disable edge capture write command */ 2243 DEBIwrite(dev, LP_MISC1, MISC1_NOEDCAP); 2244 2245 for (group = 0; group < S626_DIO_BANKS; group++) { 2246 /* clear pending events and interrupt */ 2247 DEBIwrite(dev, 2248 ((dio_private *) (dev->subdevices + 2 + 2249 group)->private)->WRCapSel, 0xffff); 2250 } 2251 2252 return 0; 2253} 2254 2255/* Now this function initializes the value of the counter (data[0]) 2256 and set the subdevice. To complete with trigger and interrupt 2257 configuration */ 2258static int s626_enc_insn_config(comedi_device *dev, comedi_subdevice *s, 2259 comedi_insn *insn, lsampl_t *data) 2260{ 2261 uint16_t Setup = (LOADSRC_INDX << BF_LOADSRC) | /* Preload upon */ 2262 /* index. */ 2263 (INDXSRC_SOFT << BF_INDXSRC) | /* Disable hardware index. */ 2264 (CLKSRC_COUNTER << BF_CLKSRC) | /* Operating mode is Counter. */ 2265 (CLKPOL_POS << BF_CLKPOL) | /* Active high clock. */ 2266 /* ( CNTDIR_UP << BF_CLKPOL ) | // Count direction is Down. */ 2267 (CLKMULT_1X << BF_CLKMULT) | /* Clock multiplier is 1x. */ 2268 (CLKENAB_INDEX << BF_CLKENAB); 2269 /* uint16_t DisableIntSrc=TRUE; */ 2270 /* uint32_t Preloadvalue; //Counter initial value */ 2271 uint16_t valueSrclatch = LATCHSRC_AB_READ; 2272 uint16_t enab = CLKENAB_ALWAYS; 2273 enc_private *k = &encpriv[CR_CHAN(insn->chanspec)]; 2274 2275 DEBUG("s626_enc_insn_config: encoder config\n"); 2276 2277 /* (data==NULL) ? (Preloadvalue=0) : (Preloadvalue=data[0]); */ 2278 2279 k->SetMode(dev, k, Setup, TRUE); 2280 Preload(dev, k, *(insn->data)); 2281 k->PulseIndex(dev, k); 2282 SetLatchSource(dev, k, valueSrclatch); 2283 k->SetEnable(dev, k, (uint16_t) (enab != 0)); 2284 2285 return insn->n; 2286} 2287 2288static int s626_enc_insn_read(comedi_device *dev, comedi_subdevice *s, 2289 comedi_insn *insn, lsampl_t *data) 2290{ 2291 2292 int n; 2293 enc_private *k = &encpriv[CR_CHAN(insn->chanspec)]; 2294 2295 DEBUG("s626_enc_insn_read: encoder read channel %d \n", 2296 CR_CHAN(insn->chanspec)); 2297 2298 for (n = 0; n < insn->n; n++) 2299 data[n] = ReadLatch(dev, k); 2300 2301 DEBUG("s626_enc_insn_read: encoder sample %d\n", data[n]); 2302 2303 return n; 2304} 2305 2306static int s626_enc_insn_write(comedi_device *dev, comedi_subdevice *s, 2307 comedi_insn *insn, lsampl_t *data) 2308{ 2309 2310 enc_private *k = &encpriv[CR_CHAN(insn->chanspec)]; 2311 2312 DEBUG("s626_enc_insn_write: encoder write channel %d \n", 2313 CR_CHAN(insn->chanspec)); 2314 2315 /* Set the preload register */ 2316 Preload(dev, k, data[0]); 2317 2318 /* Software index pulse forces the preload register to load */ 2319 /* into the counter */ 2320 k->SetLoadTrig(dev, k, 0); 2321 k->PulseIndex(dev, k); 2322 k->SetLoadTrig(dev, k, 2); 2323 2324 DEBUG("s626_enc_insn_write: End encoder write\n"); 2325 2326 return 1; 2327} 2328 2329static void s626_timer_load(comedi_device *dev, enc_private *k, int tick) 2330{ 2331 uint16_t Setup = (LOADSRC_INDX << BF_LOADSRC) | /* Preload upon */ 2332 /* index. */ 2333 (INDXSRC_SOFT << BF_INDXSRC) | /* Disable hardware index. */ 2334 (CLKSRC_TIMER << BF_CLKSRC) | /* Operating mode is Timer. */ 2335 (CLKPOL_POS << BF_CLKPOL) | /* Active high clock. */ 2336 (CNTDIR_DOWN << BF_CLKPOL) | /* Count direction is Down. */ 2337 (CLKMULT_1X << BF_CLKMULT) | /* Clock multiplier is 1x. */ 2338 (CLKENAB_INDEX << BF_CLKENAB); 2339 uint16_t valueSrclatch = LATCHSRC_A_INDXA; 2340 /* uint16_t enab=CLKENAB_ALWAYS; */ 2341 2342 k->SetMode(dev, k, Setup, FALSE); 2343 2344 /* Set the preload register */ 2345 Preload(dev, k, tick); 2346 2347 /* Software index pulse forces the preload register to load */ 2348 /* into the counter */ 2349 k->SetLoadTrig(dev, k, 0); 2350 k->PulseIndex(dev, k); 2351 2352 /* set reload on counter overflow */ 2353 k->SetLoadTrig(dev, k, 1); 2354 2355 /* set interrupt on overflow */ 2356 k->SetIntSrc(dev, k, INTSRC_OVER); 2357 2358 SetLatchSource(dev, k, valueSrclatch); 2359 /* k->SetEnable(dev,k,(uint16_t)(enab != 0)); */ 2360} 2361 2362/* *********** DAC FUNCTIONS *********** */ 2363 2364/* Slot 0 base settings. */ 2365#define VECT0 (XSD2 | RSD3 | SIB_A2) 2366/* Slot 0 always shifts in 0xFF and store it to FB_BUFFER2. */ 2367 2368/* TrimDac LogicalChan-to-PhysicalChan mapping table. */ 2369static uint8_t trimchan[] = { 10, 9, 8, 3, 2, 7, 6, 1, 0, 5, 4 }; 2370 2371/* TrimDac LogicalChan-to-EepromAdrs mapping table. */ 2372static uint8_t trimadrs[] = 2373 { 0x40, 0x41, 0x42, 0x50, 0x51, 0x52, 0x53, 0x60, 0x61, 0x62, 0x63 }; 2374 2375static void LoadTrimDACs(comedi_device *dev) 2376{ 2377 register uint8_t i; 2378 2379 /* Copy TrimDac setpoint values from EEPROM to TrimDacs. */ 2380 for (i = 0; i < (sizeof(trimchan) / sizeof(trimchan[0])); i++) 2381 WriteTrimDAC(dev, i, I2Cread(dev, trimadrs[i])); 2382} 2383 2384static void WriteTrimDAC(comedi_device *dev, uint8_t LogicalChan, 2385 uint8_t DacData) 2386{ 2387 uint32_t chan; 2388 2389 /* Save the new setpoint in case the application needs to read it back later. */ 2390 devpriv->TrimSetpoint[LogicalChan] = (uint8_t) DacData; 2391 2392 /* Map logical channel number to physical channel number. */ 2393 chan = (uint32_t) trimchan[LogicalChan]; 2394 2395 /* Set up TSL2 records for TrimDac write operation. All slots shift 2396 * 0xFF in from pulled-up SD3 so that the end of the slot sequence 2397 * can be detected. 2398 */ 2399 2400 SETVECT(2, XSD2 | XFIFO_1 | WS3); 2401 /* Slot 2: Send high uint8_t to target TrimDac. */ 2402 SETVECT(3, XSD2 | XFIFO_0 | WS3); 2403 /* Slot 3: Send low uint8_t to target TrimDac. */ 2404 SETVECT(4, XSD2 | XFIFO_3 | WS1); 2405 /* Slot 4: Send NOP high uint8_t to DAC0 to keep clock running. */ 2406 SETVECT(5, XSD2 | XFIFO_2 | WS1 | EOS); 2407 /* Slot 5: Send NOP low uint8_t to DAC0. */ 2408 2409 /* Construct and transmit target DAC's serial packet: 2410 * ( 0000 AAAA ), ( DDDD DDDD ),( 0x00 ),( 0x00 ) where A<3:0> is the 2411 * DAC channel's address, and D<7:0> is the DAC setpoint. Append a 2412 * WORD value (that writes a channel 0 NOP command to a non-existent 2413 * main DAC channel) that serves to keep the clock running after the 2414 * packet has been sent to the target DAC. 2415 */ 2416 2417 /* Address the DAC channel within the trimdac device. */ 2418 SendDAC(dev, ((uint32_t) chan << 8) 2419 | (uint32_t) DacData); /* Include DAC setpoint data. */ 2420} 2421 2422/* ************** EEPROM ACCESS FUNCTIONS ************** */ 2423/* Read uint8_t from EEPROM. */ 2424 2425static uint8_t I2Cread(comedi_device *dev, uint8_t addr) 2426{ 2427 uint8_t rtnval; 2428 2429 /* Send EEPROM target address. */ 2430 if (I2Chandshake(dev, I2C_B2(I2C_ATTRSTART, I2CW) 2431 /* Byte2 = I2C command: write to I2C EEPROM device. */ 2432 | I2C_B1(I2C_ATTRSTOP, addr) 2433 /* Byte1 = EEPROM internal target address. */ 2434 | I2C_B0(I2C_ATTRNOP, 0))) { /* Byte0 = Not sent. */ 2435 /* Abort function and declare error if handshake failed. */ 2436 DEBUG("I2Cread: error handshake I2Cread a\n"); 2437 return 0; 2438 } 2439 /* Execute EEPROM read. */ 2440 if (I2Chandshake(dev, I2C_B2(I2C_ATTRSTART, I2CR) /* Byte2 = I2C */ 2441 /* command: read */ 2442 /* from I2C EEPROM */ 2443 /* device. */ 2444 | I2C_B1(I2C_ATTRSTOP, 0) /* Byte1 receives */ 2445 /* uint8_t from */ 2446 /* EEPROM. */ 2447 | I2C_B0(I2C_ATTRNOP, 0))) { /* Byte0 = Not sent. */ 2448 2449 /* Abort function and declare error if handshake failed. */ 2450 DEBUG("I2Cread: error handshake I2Cread b\n"); 2451 return 0; 2452 } 2453 /* Return copy of EEPROM value. */ 2454 rtnval = (uint8_t) (RR7146(P_I2CCTRL) >> 16); 2455 return rtnval; 2456} 2457 2458static uint32_t I2Chandshake(comedi_device *dev, uint32_t val) 2459{ 2460 /* Write I2C command to I2C Transfer Control shadow register. */ 2461 WR7146(P_I2CCTRL, val); 2462 2463 /* Upload I2C shadow registers into working registers and wait for */ 2464 /* upload confirmation. */ 2465 2466 MC_ENABLE(P_MC2, MC2_UPLD_IIC); 2467 while (!MC_TEST(P_MC2, MC2_UPLD_IIC)) 2468 ; 2469 2470 /* Wait until I2C bus transfer is finished or an error occurs. */ 2471 while ((RR7146(P_I2CCTRL) & (I2C_BUSY | I2C_ERR)) == I2C_BUSY) 2472 ; 2473 2474 /* Return non-zero if I2C error occured. */ 2475 return RR7146(P_I2CCTRL) & I2C_ERR; 2476 2477} 2478 2479/* Private helper function: Write setpoint to an application DAC channel. */ 2480 2481static void SetDAC(comedi_device *dev, uint16_t chan, short dacdata) 2482{ 2483 register uint16_t signmask; 2484 register uint32_t WSImage; 2485 2486 /* Adjust DAC data polarity and set up Polarity Control Register */ 2487 /* image. */ 2488 signmask = 1 << chan; 2489 if (dacdata < 0) { 2490 dacdata = -dacdata; 2491 devpriv->Dacpol |= signmask; 2492 } else 2493 devpriv->Dacpol &= ~signmask; 2494 2495 /* Limit DAC setpoint value to valid range. */ 2496 if ((uint16_t) dacdata > 0x1FFF) 2497 dacdata = 0x1FFF; 2498 2499 /* Set up TSL2 records (aka "vectors") for DAC update. Vectors V2 2500 * and V3 transmit the setpoint to the target DAC. V4 and V5 send 2501 * data to a non-existent TrimDac channel just to keep the clock 2502 * running after sending data to the target DAC. This is necessary 2503 * to eliminate the clock glitch that would otherwise occur at the 2504 * end of the target DAC's serial data stream. When the sequence 2505 * restarts at V0 (after executing V5), the gate array automatically 2506 * disables gating for the DAC clock and all DAC chip selects. 2507 */ 2508 2509 WSImage = (chan & 2) ? WS1 : WS2; 2510 /* Choose DAC chip select to be asserted. */ 2511 SETVECT(2, XSD2 | XFIFO_1 | WSImage); 2512 /* Slot 2: Transmit high data byte to target DAC. */ 2513 SETVECT(3, XSD2 | XFIFO_0 | WSImage); 2514 /* Slot 3: Transmit low data byte to target DAC. */ 2515 SETVECT(4, XSD2 | XFIFO_3 | WS3); 2516 /* Slot 4: Transmit to non-existent TrimDac channel to keep clock */ 2517 SETVECT(5, XSD2 | XFIFO_2 | WS3 | EOS); 2518 /* Slot 5: running after writing target DAC's low data byte. */ 2519 2520 /* Construct and transmit target DAC's serial packet: 2521 * ( A10D DDDD ),( DDDD DDDD ),( 0x0F ),( 0x00 ) where A is chan<0>, 2522 * and D<12:0> is the DAC setpoint. Append a WORD value (that writes 2523 * to a non-existent TrimDac channel) that serves to keep the clock 2524 * running after the packet has been sent to the target DAC. 2525 */ 2526 SendDAC(dev, 0x0F000000 2527 /* Continue clock after target DAC data (write to non-existent trimdac). */ 2528 | 0x00004000 2529 /* Address the two main dual-DAC devices (TSL's chip select enables 2530 * target device). */ 2531 | ((uint32_t) (chan & 1) << 15) 2532 /* Address the DAC channel within the device. */ 2533 | (uint32_t) dacdata); /* Include DAC setpoint data. */ 2534 2535} 2536 2537/* Private helper function: Transmit serial data to DAC via Audio 2538 * channel 2. Assumes: (1) TSL2 slot records initialized, and (2) 2539 * Dacpol contains valid target image. 2540 */ 2541 2542static void SendDAC(comedi_device *dev, uint32_t val) 2543{ 2544 2545 /* START THE SERIAL CLOCK RUNNING ------------- */ 2546 2547 /* Assert DAC polarity control and enable gating of DAC serial clock 2548 * and audio bit stream signals. At this point in time we must be 2549 * assured of being in time slot 0. If we are not in slot 0, the 2550 * serial clock and audio stream signals will be disabled; this is 2551 * because the following DEBIwrite statement (which enables signals 2552 * to be passed through the gate array) would execute before the 2553 * trailing edge of WS1/WS3 (which turns off the signals), thus 2554 * causing the signals to be inactive during the DAC write. 2555 */ 2556 DEBIwrite(dev, LP_DACPOL, devpriv->Dacpol); 2557 2558 /* TRANSFER OUTPUT DWORD VALUE INTO A2'S OUTPUT FIFO ---------------- */ 2559 2560 /* Copy DAC setpoint value to DAC's output DMA buffer. */ 2561 2562 /* WR7146( (uint32_t)devpriv->pDacWBuf, val ); */ 2563 *devpriv->pDacWBuf = val; 2564 2565 /* enab the output DMA transfer. This will cause the DMAC to copy 2566 * the DAC's data value to A2's output FIFO. The DMA transfer will 2567 * then immediately terminate because the protection address is 2568 * reached upon transfer of the first DWORD value. 2569 */ 2570 MC_ENABLE(P_MC1, MC1_A2OUT); 2571 2572 /* While the DMA transfer is executing ... */ 2573 2574 /* Reset Audio2 output FIFO's underflow flag (along with any other 2575 * FIFO underflow/overflow flags). When set, this flag will 2576 * indicate that we have emerged from slot 0. 2577 */ 2578 WR7146(P_ISR, ISR_AFOU); 2579 2580 /* Wait for the DMA transfer to finish so that there will be data 2581 * available in the FIFO when time slot 1 tries to transfer a DWORD 2582 * from the FIFO to the output buffer register. We test for DMA 2583 * Done by polling the DMAC enable flag; this flag is automatically 2584 * cleared when the transfer has finished. 2585 */ 2586 while ((RR7146(P_MC1) & MC1_A2OUT) != 0) 2587 ; 2588 2589 /* START THE OUTPUT STREAM TO THE TARGET DAC -------------------- */ 2590 2591 /* FIFO data is now available, so we enable execution of time slots 2592 * 1 and higher by clearing the EOS flag in slot 0. Note that SD3 2593 * will be shifted in and stored in FB_BUFFER2 for end-of-slot-list 2594 * detection. 2595 */ 2596 SETVECT(0, XSD2 | RSD3 | SIB_A2); 2597 2598 /* Wait for slot 1 to execute to ensure that the Packet will be 2599 * transmitted. This is detected by polling the Audio2 output FIFO 2600 * underflow flag, which will be set when slot 1 execution has 2601 * finished transferring the DAC's data DWORD from the output FIFO 2602 * to the output buffer register. 2603 */ 2604 while ((RR7146(P_SSR) & SSR_AF2_OUT) == 0) 2605 ; 2606 2607 /* Set up to trap execution at slot 0 when the TSL sequencer cycles 2608 * back to slot 0 after executing the EOS in slot 5. Also, 2609 * simultaneously shift out and in the 0x00 that is ALWAYS the value 2610 * stored in the last byte to be shifted out of the FIFO's DWORD 2611 * buffer register. 2612 */ 2613 SETVECT(0, XSD2 | XFIFO_2 | RSD2 | SIB_A2 | EOS); 2614 2615 /* WAIT FOR THE TRANSACTION TO FINISH ----------------------- */ 2616 2617 /* Wait for the TSL to finish executing all time slots before 2618 * exiting this function. We must do this so that the next DAC 2619 * write doesn't start, thereby enabling clock/chip select signals: 2620 * 2621 * 1. Before the TSL sequence cycles back to slot 0, which disables 2622 * the clock/cs signal gating and traps slot // list execution. 2623 * we have not yet finished slot 5 then the clock/cs signals are 2624 * still gated and we have not finished transmitting the stream. 2625 * 2626 * 2. While slots 2-5 are executing due to a late slot 0 trap. In 2627 * this case, the slot sequence is currently repeating, but with 2628 * clock/cs signals disabled. We must wait for slot 0 to trap 2629 * execution before setting up the next DAC setpoint DMA transfer 2630 * and enabling the clock/cs signals. To detect the end of slot 5, 2631 * we test for the FB_BUFFER2 MSB contents to be equal to 0xFF. If 2632 * the TSL has not yet finished executing slot 5 ... 2633 */ 2634 if ((RR7146(P_FB_BUFFER2) & 0xFF000000) != 0) { 2635 /* The trap was set on time and we are still executing somewhere 2636 * in slots 2-5, so we now wait for slot 0 to execute and trap 2637 * TSL execution. This is detected when FB_BUFFER2 MSB changes 2638 * from 0xFF to 0x00, which slot 0 causes to happen by shifting 2639 * out/in on SD2 the 0x00 that is always referenced by slot 5. 2640 */ 2641 while ((RR7146(P_FB_BUFFER2) & 0xFF000000) != 0) 2642 ; 2643 } 2644 /* Either (1) we were too late setting the slot 0 trap; the TSL 2645 * sequencer restarted slot 0 before we could set the EOS trap flag, 2646 * or (2) we were not late and execution is now trapped at slot 0. 2647 * In either case, we must now change slot 0 so that it will store 2648 * value 0xFF (instead of 0x00) to FB_BUFFER2 next time it executes. 2649 * In order to do this, we reprogram slot 0 so that it will shift in 2650 * SD3, which is driven only by a pull-up resistor. 2651 */ 2652 SETVECT(0, RSD3 | SIB_A2 | EOS); 2653 2654 /* Wait for slot 0 to execute, at which time the TSL is setup for 2655 * the next DAC write. This is detected when FB_BUFFER2 MSB changes 2656 * from 0x00 to 0xFF. 2657 */ 2658 while ((RR7146(P_FB_BUFFER2) & 0xFF000000) == 0) 2659 ; 2660} 2661 2662static void WriteMISC2(comedi_device *dev, uint16_t NewImage) 2663{ 2664 DEBIwrite(dev, LP_MISC1, MISC1_WENABLE); /* enab writes to */ 2665 /* MISC2 register. */ 2666 DEBIwrite(dev, LP_WRMISC2, NewImage); /* Write new image to MISC2. */ 2667 DEBIwrite(dev, LP_MISC1, MISC1_WDISABLE); /* Disable writes to MISC2. */ 2668} 2669 2670/* Initialize the DEBI interface for all transfers. */ 2671 2672static uint16_t DEBIread(comedi_device *dev, uint16_t addr) 2673{ 2674 uint16_t retval; 2675 2676 /* Set up DEBI control register value in shadow RAM. */ 2677 WR7146(P_DEBICMD, DEBI_CMD_RDWORD | addr); 2678 2679 /* Execute the DEBI transfer. */ 2680 DEBItransfer(dev); 2681 2682 /* Fetch target register value. */ 2683 retval = (uint16_t) RR7146(P_DEBIAD); 2684 2685 /* Return register value. */ 2686 return retval; 2687} 2688 2689/* Execute a DEBI transfer. This must be called from within a */ 2690/* critical section. */ 2691static void DEBItransfer(comedi_device *dev) 2692{ 2693 /* Initiate upload of shadow RAM to DEBI control register. */ 2694 MC_ENABLE(P_MC2, MC2_UPLD_DEBI); 2695 2696 /* Wait for completion of upload from shadow RAM to DEBI control */ 2697 /* register. */ 2698 while (!MC_TEST(P_MC2, MC2_UPLD_DEBI)) 2699 ; 2700 2701 /* Wait until DEBI transfer is done. */ 2702 while (RR7146(P_PSR) & PSR_DEBI_S) 2703 ; 2704} 2705 2706/* Write a value to a gate array register. */ 2707static void DEBIwrite(comedi_device *dev, uint16_t addr, uint16_t wdata) 2708{ 2709 2710 /* Set up DEBI control register value in shadow RAM. */ 2711 WR7146(P_DEBICMD, DEBI_CMD_WRWORD | addr); 2712 WR7146(P_DEBIAD, wdata); 2713 2714 /* Execute the DEBI transfer. */ 2715 DEBItransfer(dev); 2716} 2717 2718/* Replace the specified bits in a gate array register. Imports: mask 2719 * specifies bits that are to be preserved, wdata is new value to be 2720 * or'd with the masked original. 2721 */ 2722static void DEBIreplace(comedi_device *dev, uint16_t addr, uint16_t mask, 2723 uint16_t wdata) 2724{ 2725 2726 /* Copy target gate array register into P_DEBIAD register. */ 2727 WR7146(P_DEBICMD, DEBI_CMD_RDWORD | addr); 2728 /* Set up DEBI control reg value in shadow RAM. */ 2729 DEBItransfer(dev); /* Execute the DEBI Read transfer. */ 2730 2731 /* Write back the modified image. */ 2732 WR7146(P_DEBICMD, DEBI_CMD_WRWORD | addr); 2733 /* Set up DEBI control reg value in shadow RAM. */ 2734 2735 WR7146(P_DEBIAD, wdata | ((uint16_t) RR7146(P_DEBIAD) & mask)); 2736 /* Modify the register image. */ 2737 DEBItransfer(dev); /* Execute the DEBI Write transfer. */ 2738} 2739 2740static void CloseDMAB(comedi_device *dev, DMABUF *pdma, size_t bsize) 2741{ 2742 void *vbptr; 2743 dma_addr_t vpptr; 2744 2745 DEBUG("CloseDMAB: Entering S626DRV_CloseDMAB():\n"); 2746 if (pdma == NULL) 2747 return; 2748 /* find the matching allocation from the board struct */ 2749 2750 vbptr = pdma->LogicalBase; 2751 vpptr = pdma->PhysicalBase; 2752 if (vbptr) { 2753 pci_free_consistent(devpriv->pdev, bsize, vbptr, vpptr); 2754 pdma->LogicalBase = 0; 2755 pdma->PhysicalBase = 0; 2756 2757 DEBUG("CloseDMAB(): Logical=%p, bsize=%d, Physical=0x%x\n", 2758 vbptr, bsize, (uint32_t) vpptr); 2759 } 2760} 2761 2762/* ****** COUNTER FUNCTIONS ******* */ 2763/* All counter functions address a specific counter by means of the 2764 * "Counter" argument, which is a logical counter number. The Counter 2765 * argument may have any of the following legal values: 0=0A, 1=1A, 2766 * 2=2A, 3=0B, 4=1B, 5=2B. 2767 */ 2768 2769/* Forward declarations for functions that are common to both A and B counters: */ 2770 2771/* ****** PRIVATE COUNTER FUNCTIONS ****** */ 2772 2773/* Read a counter's output latch. */ 2774 2775static uint32_t ReadLatch(comedi_device *dev, enc_private *k) 2776{ 2777 register uint32_t value; 2778 /* DEBUG FIXME DEBUG("ReadLatch: Read Latch enter\n"); */ 2779 2780 /* Latch counts and fetch LSW of latched counts value. */ 2781 value = (uint32_t) DEBIread(dev, k->MyLatchLsw); 2782 2783 /* Fetch MSW of latched counts and combine with LSW. */ 2784 value |= ((uint32_t) DEBIread(dev, k->MyLatchLsw + 2) << 16); 2785 2786 /* DEBUG FIXME DEBUG("ReadLatch: Read Latch exit\n"); */ 2787 2788 /* Return latched counts. */ 2789 return value; 2790} 2791 2792/* Reset a counter's index and overflow event capture flags. */ 2793 2794static void ResetCapFlags_A(comedi_device *dev, enc_private *k) 2795{ 2796 DEBIreplace(dev, k->MyCRB, (uint16_t) (~CRBMSK_INTCTRL), 2797 CRBMSK_INTRESETCMD | CRBMSK_INTRESET_A); 2798} 2799 2800static void ResetCapFlags_B(comedi_device *dev, enc_private *k) 2801{ 2802 DEBIreplace(dev, k->MyCRB, (uint16_t) (~CRBMSK_INTCTRL), 2803 CRBMSK_INTRESETCMD | CRBMSK_INTRESET_B); 2804} 2805 2806/* Return counter setup in a format (COUNTER_SETUP) that is consistent */ 2807/* for both A and B counters. */ 2808 2809static uint16_t GetMode_A(comedi_device *dev, enc_private *k) 2810{ 2811 register uint16_t cra; 2812 register uint16_t crb; 2813 register uint16_t setup; 2814 2815 /* Fetch CRA and CRB register images. */ 2816 cra = DEBIread(dev, k->MyCRA); 2817 crb = DEBIread(dev, k->MyCRB); 2818 2819 /* Populate the standardized counter setup bit fields. Note: */ 2820 /* IndexSrc is restricted to ENC_X or IndxPol. */ 2821 setup = ((cra & STDMSK_LOADSRC) /* LoadSrc = LoadSrcA. */ 2822 | ((crb << (STDBIT_LATCHSRC - CRBBIT_LATCHSRC)) & STDMSK_LATCHSRC) /* LatchSrc = LatchSrcA. */ 2823 | ((cra << (STDBIT_INTSRC - CRABIT_INTSRC_A)) & STDMSK_INTSRC) /* IntSrc = IntSrcA. */ 2824 | ((cra << (STDBIT_INDXSRC - (CRABIT_INDXSRC_A + 1))) & STDMSK_INDXSRC) /* IndxSrc = IndxSrcA<1>. */ 2825 | ((cra >> (CRABIT_INDXPOL_A - STDBIT_INDXPOL)) & STDMSK_INDXPOL) /* IndxPol = IndxPolA. */ 2826 | ((crb >> (CRBBIT_CLKENAB_A - STDBIT_CLKENAB)) & STDMSK_CLKENAB)); /* ClkEnab = ClkEnabA. */ 2827 2828 /* Adjust mode-dependent parameters. */ 2829 if (cra & (2 << CRABIT_CLKSRC_A)) /* If Timer mode (ClkSrcA<1> == 1): */ 2830 setup |= ((CLKSRC_TIMER << STDBIT_CLKSRC) /* Indicate Timer mode. */ 2831 | ((cra << (STDBIT_CLKPOL - CRABIT_CLKSRC_A)) & STDMSK_CLKPOL) /* Set ClkPol to indicate count direction (ClkSrcA<0>). */ 2832 | (MULT_X1 << STDBIT_CLKMULT)); /* ClkMult must be 1x in Timer mode. */ 2833 2834 else /* If Counter mode (ClkSrcA<1> == 0): */ 2835 setup |= ((CLKSRC_COUNTER << STDBIT_CLKSRC) /* Indicate Counter mode. */ 2836 | ((cra >> (CRABIT_CLKPOL_A - STDBIT_CLKPOL)) & STDMSK_CLKPOL) /* Pass through ClkPol. */ 2837 | (((cra & CRAMSK_CLKMULT_A) == (MULT_X0 << CRABIT_CLKMULT_A)) ? /* Force ClkMult to 1x if not legal, else pass through. */ 2838 (MULT_X1 << STDBIT_CLKMULT) : 2839 ((cra >> (CRABIT_CLKMULT_A - 2840 STDBIT_CLKMULT)) & 2841 STDMSK_CLKMULT))); 2842 2843 /* Return adjusted counter setup. */ 2844 return setup; 2845} 2846 2847static uint16_t GetMode_B(comedi_device *dev, enc_private *k) 2848{ 2849 register uint16_t cra; 2850 register uint16_t crb; 2851 register uint16_t setup; 2852 2853 /* Fetch CRA and CRB register images. */ 2854 cra = DEBIread(dev, k->MyCRA); 2855 crb = DEBIread(dev, k->MyCRB); 2856 2857 /* Populate the standardized counter setup bit fields. Note: */ 2858 /* IndexSrc is restricted to ENC_X or IndxPol. */ 2859 setup = (((crb << (STDBIT_INTSRC - CRBBIT_INTSRC_B)) & STDMSK_INTSRC) /* IntSrc = IntSrcB. */ 2860 | ((crb << (STDBIT_LATCHSRC - CRBBIT_LATCHSRC)) & STDMSK_LATCHSRC) /* LatchSrc = LatchSrcB. */ 2861 | ((crb << (STDBIT_LOADSRC - CRBBIT_LOADSRC_B)) & STDMSK_LOADSRC) /* LoadSrc = LoadSrcB. */ 2862 | ((crb << (STDBIT_INDXPOL - CRBBIT_INDXPOL_B)) & STDMSK_INDXPOL) /* IndxPol = IndxPolB. */ 2863 | ((crb >> (CRBBIT_CLKENAB_B - STDBIT_CLKENAB)) & STDMSK_CLKENAB) /* ClkEnab = ClkEnabB. */ 2864 | ((cra >> ((CRABIT_INDXSRC_B + 1) - STDBIT_INDXSRC)) & STDMSK_INDXSRC)); /* IndxSrc = IndxSrcB<1>. */ 2865 2866 /* Adjust mode-dependent parameters. */ 2867 if ((crb & CRBMSK_CLKMULT_B) == (MULT_X0 << CRBBIT_CLKMULT_B)) /* If Extender mode (ClkMultB == MULT_X0): */ 2868 setup |= ((CLKSRC_EXTENDER << STDBIT_CLKSRC) /* Indicate Extender mode. */ 2869 | (MULT_X1 << STDBIT_CLKMULT) /* Indicate multiplier is 1x. */ 2870 | ((cra >> (CRABIT_CLKSRC_B - STDBIT_CLKPOL)) & STDMSK_CLKPOL)); /* Set ClkPol equal to Timer count direction (ClkSrcB<0>). */ 2871 2872 else if (cra & (2 << CRABIT_CLKSRC_B)) /* If Timer mode (ClkSrcB<1> == 1): */ 2873 setup |= ((CLKSRC_TIMER << STDBIT_CLKSRC) /* Indicate Timer mode. */ 2874 | (MULT_X1 << STDBIT_CLKMULT) /* Indicate multiplier is 1x. */ 2875 | ((cra >> (CRABIT_CLKSRC_B - STDBIT_CLKPOL)) & STDMSK_CLKPOL)); /* Set ClkPol equal to Timer count direction (ClkSrcB<0>). */ 2876 2877 else /* If Counter mode (ClkSrcB<1> == 0): */ 2878 setup |= ((CLKSRC_COUNTER << STDBIT_CLKSRC) /* Indicate Timer mode. */ 2879 | ((crb >> (CRBBIT_CLKMULT_B - STDBIT_CLKMULT)) & STDMSK_CLKMULT) /* Clock multiplier is passed through. */ 2880 | ((crb << (STDBIT_CLKPOL - CRBBIT_CLKPOL_B)) & STDMSK_CLKPOL)); /* Clock polarity is passed through. */ 2881 2882 /* Return adjusted counter setup. */ 2883 return setup; 2884} 2885 2886/* 2887 * Set the operating mode for the specified counter. The setup 2888 * parameter is treated as a COUNTER_SETUP data type. The following 2889 * parameters are programmable (all other parms are ignored): ClkMult, 2890 * ClkPol, ClkEnab, IndexSrc, IndexPol, LoadSrc. 2891 */ 2892 2893static void SetMode_A(comedi_device *dev, enc_private *k, uint16_t Setup, 2894 uint16_t DisableIntSrc) 2895{ 2896 register uint16_t cra; 2897 register uint16_t crb; 2898 register uint16_t setup = Setup; /* Cache the Standard Setup. */ 2899 2900 /* Initialize CRA and CRB images. */ 2901 cra = ((setup & CRAMSK_LOADSRC_A) /* Preload trigger is passed through. */ 2902 | ((setup & STDMSK_INDXSRC) >> (STDBIT_INDXSRC - (CRABIT_INDXSRC_A + 1)))); /* IndexSrc is restricted to ENC_X or IndxPol. */ 2903 2904 crb = (CRBMSK_INTRESETCMD | CRBMSK_INTRESET_A /* Reset any pending CounterA event captures. */ 2905 | ((setup & STDMSK_CLKENAB) << (CRBBIT_CLKENAB_A - STDBIT_CLKENAB))); /* Clock enable is passed through. */ 2906 2907 /* Force IntSrc to Disabled if DisableIntSrc is asserted. */ 2908 if (!DisableIntSrc) 2909 cra |= ((setup & STDMSK_INTSRC) >> (STDBIT_INTSRC - 2910 CRABIT_INTSRC_A)); 2911 2912 /* Populate all mode-dependent attributes of CRA & CRB images. */ 2913 switch ((setup & STDMSK_CLKSRC) >> STDBIT_CLKSRC) { 2914 case CLKSRC_EXTENDER: /* Extender Mode: Force to Timer mode */ 2915 /* (Extender valid only for B counters). */ 2916 2917 case CLKSRC_TIMER: /* Timer Mode: */ 2918 cra |= ((2 << CRABIT_CLKSRC_A) /* ClkSrcA<1> selects system clock */ 2919 | ((setup & STDMSK_CLKPOL) >> (STDBIT_CLKPOL - CRABIT_CLKSRC_A)) /* with count direction (ClkSrcA<0>) obtained from ClkPol. */ 2920 | (1 << CRABIT_CLKPOL_A) /* ClkPolA behaves as always-on clock enable. */ 2921 | (MULT_X1 << CRABIT_CLKMULT_A)); /* ClkMult must be 1x. */ 2922 break; 2923 2924 default: /* Counter Mode: */ 2925 cra |= (CLKSRC_COUNTER /* Select ENC_C and ENC_D as clock/direction inputs. */ 2926 | ((setup & STDMSK_CLKPOL) << (CRABIT_CLKPOL_A - STDBIT_CLKPOL)) /* Clock polarity is passed through. */ 2927 | (((setup & STDMSK_CLKMULT) == (MULT_X0 << STDBIT_CLKMULT)) ? /* Force multiplier to x1 if not legal, otherwise pass through. */ 2928 (MULT_X1 << CRABIT_CLKMULT_A) : 2929 ((setup & STDMSK_CLKMULT) << (CRABIT_CLKMULT_A - 2930 STDBIT_CLKMULT)))); 2931 } 2932 2933 /* Force positive index polarity if IndxSrc is software-driven only, */ 2934 /* otherwise pass it through. */ 2935 if (~setup & STDMSK_INDXSRC) 2936 cra |= ((setup & STDMSK_INDXPOL) << (CRABIT_INDXPOL_A - 2937 STDBIT_INDXPOL)); 2938 2939 /* If IntSrc has been forced to Disabled, update the MISC2 interrupt */ 2940 /* enable mask to indicate the counter interrupt is disabled. */ 2941 if (DisableIntSrc) 2942 devpriv->CounterIntEnabs &= ~k->MyEventBits[3]; 2943 2944 /* While retaining CounterB and LatchSrc configurations, program the */ 2945 /* new counter operating mode. */ 2946 DEBIreplace(dev, k->MyCRA, CRAMSK_INDXSRC_B | CRAMSK_CLKSRC_B, cra); 2947 DEBIreplace(dev, k->MyCRB, 2948 (uint16_t) (~(CRBMSK_INTCTRL | CRBMSK_CLKENAB_A)), crb); 2949} 2950 2951static void SetMode_B(comedi_device *dev, enc_private *k, uint16_t Setup, 2952 uint16_t DisableIntSrc) 2953{ 2954 register uint16_t cra; 2955 register uint16_t crb; 2956 register uint16_t setup = Setup; /* Cache the Standard Setup. */ 2957 2958 /* Initialize CRA and CRB images. */ 2959 cra = ((setup & STDMSK_INDXSRC) << ((CRABIT_INDXSRC_B + 1) - STDBIT_INDXSRC)); /* IndexSrc field is restricted to ENC_X or IndxPol. */ 2960 2961 crb = (CRBMSK_INTRESETCMD | CRBMSK_INTRESET_B /* Reset event captures and disable interrupts. */ 2962 | ((setup & STDMSK_CLKENAB) << (CRBBIT_CLKENAB_B - STDBIT_CLKENAB)) /* Clock enable is passed through. */ 2963 | ((setup & STDMSK_LOADSRC) >> (STDBIT_LOADSRC - CRBBIT_LOADSRC_B))); /* Preload trigger source is passed through. */ 2964 2965 /* Force IntSrc to Disabled if DisableIntSrc is asserted. */ 2966 if (!DisableIntSrc) 2967 crb |= ((setup & STDMSK_INTSRC) >> (STDBIT_INTSRC - 2968 CRBBIT_INTSRC_B)); 2969 2970 /* Populate all mode-dependent attributes of CRA & CRB images. */ 2971 switch ((setup & STDMSK_CLKSRC) >> STDBIT_CLKSRC) { 2972 case CLKSRC_TIMER: /* Timer Mode: */ 2973 cra |= ((2 << CRABIT_CLKSRC_B) /* ClkSrcB<1> selects system clock */ 2974 | ((setup & STDMSK_CLKPOL) << (CRABIT_CLKSRC_B - STDBIT_CLKPOL))); /* with direction (ClkSrcB<0>) obtained from ClkPol. */ 2975 crb |= ((1 << CRBBIT_CLKPOL_B) /* ClkPolB behaves as always-on clock enable. */ 2976 | (MULT_X1 << CRBBIT_CLKMULT_B)); /* ClkMultB must be 1x. */ 2977 break; 2978 2979 case CLKSRC_EXTENDER: /* Extender Mode: */ 2980 cra |= ((2 << CRABIT_CLKSRC_B) /* ClkSrcB source is OverflowA (same as "timer") */ 2981 | ((setup & STDMSK_CLKPOL) << (CRABIT_CLKSRC_B - STDBIT_CLKPOL))); /* with direction obtained from ClkPol. */ 2982 crb |= ((1 << CRBBIT_CLKPOL_B) /* ClkPolB controls IndexB -- always set to active. */ 2983 | (MULT_X0 << CRBBIT_CLKMULT_B)); /* ClkMultB selects OverflowA as the clock source. */ 2984 break; 2985 2986 default: /* Counter Mode: */ 2987 cra |= (CLKSRC_COUNTER << CRABIT_CLKSRC_B); /* Select ENC_C and ENC_D as clock/direction inputs. */ 2988 crb |= (((setup & STDMSK_CLKPOL) >> (STDBIT_CLKPOL - CRBBIT_CLKPOL_B)) /* ClkPol is passed through. */ 2989 | (((setup & STDMSK_CLKMULT) == (MULT_X0 << STDBIT_CLKMULT)) ? /* Force ClkMult to x1 if not legal, otherwise pass through. */ 2990 (MULT_X1 << CRBBIT_CLKMULT_B) : 2991 ((setup & STDMSK_CLKMULT) << (CRBBIT_CLKMULT_B - 2992 STDBIT_CLKMULT)))); 2993 } 2994 2995 /* Force positive index polarity if IndxSrc is software-driven only, */ 2996 /* otherwise pass it through. */ 2997 if (~setup & STDMSK_INDXSRC) 2998 crb |= ((setup & STDMSK_INDXPOL) >> (STDBIT_INDXPOL - 2999 CRBBIT_INDXPOL_B)); 3000 3001 /* If IntSrc has been forced to Disabled, update the MISC2 interrupt */ 3002 /* enable mask to indicate the counter interrupt is disabled. */ 3003 if (DisableIntSrc) 3004 devpriv->CounterIntEnabs &= ~k->MyEventBits[3]; 3005 3006 /* While retaining CounterA and LatchSrc configurations, program the */ 3007 /* new counter operating mode. */ 3008 DEBIreplace(dev, k->MyCRA, 3009 (uint16_t) (~(CRAMSK_INDXSRC_B | CRAMSK_CLKSRC_B)), cra); 3010 DEBIreplace(dev, k->MyCRB, CRBMSK_CLKENAB_A | CRBMSK_LATCHSRC, crb); 3011} 3012 3013/* Return/set a counter's enable. enab: 0=always enabled, 1=enabled by index. */ 3014 3015static void SetEnable_A(comedi_device *dev, enc_private *k, uint16_t enab) 3016{ 3017 DEBUG("SetEnable_A: SetEnable_A enter 3541\n"); 3018 DEBIreplace(dev, k->MyCRB, 3019 (uint16_t) (~(CRBMSK_INTCTRL | CRBMSK_CLKENAB_A)), 3020 (uint16_t) (enab << CRBBIT_CLKENAB_A)); 3021} 3022 3023static void SetEnable_B(comedi_device *dev, enc_private *k, uint16_t enab) 3024{ 3025 DEBIreplace(dev, k->MyCRB, 3026 (uint16_t) (~(CRBMSK_INTCTRL | CRBMSK_CLKENAB_B)), 3027 (uint16_t) (enab << CRBBIT_CLKENAB_B)); 3028} 3029 3030static uint16_t GetEnable_A(comedi_device *dev, enc_private *k) 3031{ 3032 return (DEBIread(dev, k->MyCRB) >> CRBBIT_CLKENAB_A) & 1; 3033} 3034 3035static uint16_t GetEnable_B(comedi_device *dev, enc_private *k) 3036{ 3037 return (DEBIread(dev, k->MyCRB) >> CRBBIT_CLKENAB_B) & 1; 3038} 3039 3040/* Return/set a counter pair's latch trigger source. 0: On read 3041 * access, 1: A index latches A, 2: B index latches B, 3: A overflow 3042 * latches B. 3043 */ 3044 3045static void SetLatchSource(comedi_device *dev, enc_private *k, uint16_t value) 3046{ 3047 DEBUG("SetLatchSource: SetLatchSource enter 3550 \n"); 3048 DEBIreplace(dev, k->MyCRB, 3049 (uint16_t) (~(CRBMSK_INTCTRL | CRBMSK_LATCHSRC)), 3050 (uint16_t) (value << CRBBIT_LATCHSRC)); 3051 3052 DEBUG("SetLatchSource: SetLatchSource exit \n"); 3053} 3054 3055/* 3056 * static uint16_t GetLatchSource(comedi_device *dev, enc_private *k ) 3057 * { 3058 * return ( DEBIread( dev, k->MyCRB) >> CRBBIT_LATCHSRC ) & 3; 3059 * } 3060 */ 3061 3062/* 3063 * Return/set the event that will trigger transfer of the preload 3064 * register into the counter. 0=ThisCntr_Index, 1=ThisCntr_Overflow, 3065 * 2=OverflowA (B counters only), 3=disabled. 3066 */ 3067 3068static void SetLoadTrig_A(comedi_device *dev, enc_private *k, uint16_t Trig) 3069{ 3070 DEBIreplace(dev, k->MyCRA, (uint16_t) (~CRAMSK_LOADSRC_A), 3071 (uint16_t) (Trig << CRABIT_LOADSRC_A)); 3072} 3073 3074static void SetLoadTrig_B(comedi_device *dev, enc_private *k, uint16_t Trig) 3075{ 3076 DEBIreplace(dev, k->MyCRB, 3077 (uint16_t) (~(CRBMSK_LOADSRC_B | CRBMSK_INTCTRL)), 3078 (uint16_t) (Trig << CRBBIT_LOADSRC_B)); 3079} 3080 3081static uint16_t GetLoadTrig_A(comedi_device *dev, enc_private *k) 3082{ 3083 return (DEBIread(dev, k->MyCRA) >> CRABIT_LOADSRC_A) & 3; 3084} 3085 3086static uint16_t GetLoadTrig_B(comedi_device *dev, enc_private *k) 3087{ 3088 return (DEBIread(dev, k->MyCRB) >> CRBBIT_LOADSRC_B) & 3; 3089} 3090 3091/* Return/set counter interrupt source and clear any captured 3092 * index/overflow events. IntSource: 0=Disabled, 1=OverflowOnly, 3093 * 2=IndexOnly, 3=IndexAndOverflow. 3094 */ 3095 3096static void SetIntSrc_A(comedi_device *dev, enc_private *k, 3097 uint16_t IntSource) 3098{ 3099 /* Reset any pending counter overflow or index captures. */ 3100 DEBIreplace(dev, k->MyCRB, (uint16_t) (~CRBMSK_INTCTRL), 3101 CRBMSK_INTRESETCMD | CRBMSK_INTRESET_A); 3102 3103 /* Program counter interrupt source. */ 3104 DEBIreplace(dev, k->MyCRA, ~CRAMSK_INTSRC_A, 3105 (uint16_t) (IntSource << CRABIT_INTSRC_A)); 3106 3107 /* Update MISC2 interrupt enable mask. */ 3108 devpriv->CounterIntEnabs = 3109 (devpriv->CounterIntEnabs & ~k->MyEventBits[3]) | k-> 3110 MyEventBits[IntSource]; 3111} 3112 3113static void SetIntSrc_B(comedi_device *dev, enc_private *k, 3114 uint16_t IntSource) 3115{ 3116 uint16_t crb; 3117 3118 /* Cache writeable CRB register image. */ 3119 crb = DEBIread(dev, k->MyCRB) & ~CRBMSK_INTCTRL; 3120 3121 /* Reset any pending counter overflow or index captures. */ 3122 DEBIwrite(dev, k->MyCRB, 3123 (uint16_t) (crb | CRBMSK_INTRESETCMD | CRBMSK_INTRESET_B)); 3124 3125 /* Program counter interrupt source. */ 3126 DEBIwrite(dev, k->MyCRB, 3127 (uint16_t) ((crb & ~CRBMSK_INTSRC_B) | (IntSource << 3128 CRBBIT_INTSRC_B))); 3129 3130 /* Update MISC2 interrupt enable mask. */ 3131 devpriv->CounterIntEnabs = 3132 (devpriv->CounterIntEnabs & ~k->MyEventBits[3]) | k-> 3133 MyEventBits[IntSource]; 3134} 3135 3136static uint16_t GetIntSrc_A(comedi_device *dev, enc_private *k) 3137{ 3138 return (DEBIread(dev, k->MyCRA) >> CRABIT_INTSRC_A) & 3; 3139} 3140 3141static uint16_t GetIntSrc_B(comedi_device *dev, enc_private *k) 3142{ 3143 return (DEBIread(dev, k->MyCRB) >> CRBBIT_INTSRC_B) & 3; 3144} 3145 3146/* Return/set the clock multiplier. */ 3147 3148/* static void SetClkMult(comedi_device *dev, enc_private *k, uint16_t value ) */ 3149/* { */ 3150/* k->SetMode(dev, k, (uint16_t)( ( k->GetMode(dev, k ) & ~STDMSK_CLKMULT ) | ( value << STDBIT_CLKMULT ) ), FALSE ); */ 3151/* } */ 3152 3153/* static uint16_t GetClkMult(comedi_device *dev, enc_private *k ) */ 3154/* { */ 3155/* return ( k->GetMode(dev, k ) >> STDBIT_CLKMULT ) & 3; */ 3156/* } */ 3157 3158/* Return/set the clock polarity. */ 3159 3160/* static void SetClkPol( comedi_device *dev,enc_private *k, uint16_t value ) */ 3161/* { */ 3162/* k->SetMode(dev, k, (uint16_t)( ( k->GetMode(dev, k ) & ~STDMSK_CLKPOL ) | ( value << STDBIT_CLKPOL ) ), FALSE ); */ 3163/* } */ 3164 3165/* static uint16_t GetClkPol(comedi_device *dev, enc_private *k ) */ 3166/* { */ 3167/* return ( k->GetMode(dev, k ) >> STDBIT_CLKPOL ) & 1; */ 3168/* } */ 3169 3170/* Return/set the clock source. */ 3171 3172/* static void SetClkSrc( comedi_device *dev,enc_private *k, uint16_t value ) */ 3173/* { */ 3174/* k->SetMode(dev, k, (uint16_t)( ( k->GetMode(dev, k ) & ~STDMSK_CLKSRC ) | ( value << STDBIT_CLKSRC ) ), FALSE ); */ 3175/* } */ 3176 3177/* static uint16_t GetClkSrc( comedi_device *dev,enc_private *k ) */ 3178/* { */ 3179/* return ( k->GetMode(dev, k ) >> STDBIT_CLKSRC ) & 3; */ 3180/* } */ 3181 3182/* Return/set the index polarity. */ 3183 3184/* static void SetIndexPol(comedi_device *dev, enc_private *k, uint16_t value ) */ 3185/* { */ 3186/* k->SetMode(dev, k, (uint16_t)( ( k->GetMode(dev, k ) & ~STDMSK_INDXPOL ) | ( (value != 0) << STDBIT_INDXPOL ) ), FALSE ); */ 3187/* } */ 3188 3189/* static uint16_t GetIndexPol(comedi_device *dev, enc_private *k ) */ 3190/* { */ 3191/* return ( k->GetMode(dev, k ) >> STDBIT_INDXPOL ) & 1; */ 3192/* } */ 3193 3194/* Return/set the index source. */ 3195 3196/* static void SetIndexSrc(comedi_device *dev, enc_private *k, uint16_t value ) */ 3197/* { */ 3198/* DEBUG("SetIndexSrc: set index src enter 3700\n"); */ 3199/* k->SetMode(dev, k, (uint16_t)( ( k->GetMode(dev, k ) & ~STDMSK_INDXSRC ) | ( (value != 0) << STDBIT_INDXSRC ) ), FALSE ); */ 3200/* } */ 3201 3202/* static uint16_t GetIndexSrc(comedi_device *dev, enc_private *k ) */ 3203/* { */ 3204/* return ( k->GetMode(dev, k ) >> STDBIT_INDXSRC ) & 1; */ 3205/* } */ 3206 3207/* Generate an index pulse. */ 3208 3209static void PulseIndex_A(comedi_device *dev, enc_private *k) 3210{ 3211 register uint16_t cra; 3212 3213 DEBUG("PulseIndex_A: pulse index enter\n"); 3214 3215 cra = DEBIread(dev, k->MyCRA); /* Pulse index. */ 3216 DEBIwrite(dev, k->MyCRA, (uint16_t) (cra ^ CRAMSK_INDXPOL_A)); 3217 DEBUG("PulseIndex_A: pulse index step1\n"); 3218 DEBIwrite(dev, k->MyCRA, cra); 3219} 3220 3221static void PulseIndex_B(comedi_device *dev, enc_private *k) 3222{ 3223 register uint16_t crb; 3224 3225 crb = DEBIread(dev, k->MyCRB) & ~CRBMSK_INTCTRL; /* Pulse index. */ 3226 DEBIwrite(dev, k->MyCRB, (uint16_t) (crb ^ CRBMSK_INDXPOL_B)); 3227 DEBIwrite(dev, k->MyCRB, crb); 3228} 3229 3230/* Write value into counter preload register. */ 3231 3232static void Preload(comedi_device *dev, enc_private *k, uint32_t value) 3233{ 3234 DEBUG("Preload: preload enter\n"); 3235 DEBIwrite(dev, (uint16_t) (k->MyLatchLsw), (uint16_t) value); /* Write value to preload register. */ 3236 DEBUG("Preload: preload step 1\n"); 3237 DEBIwrite(dev, (uint16_t) (k->MyLatchLsw + 2), 3238 (uint16_t) (value >> 16)); 3239} 3240 3241static void CountersInit(comedi_device *dev) 3242{ 3243 int chan; 3244 enc_private *k; 3245 uint16_t Setup = (LOADSRC_INDX << BF_LOADSRC) | /* Preload upon */ 3246 /* index. */ 3247 (INDXSRC_SOFT << BF_INDXSRC) | /* Disable hardware index. */ 3248 (CLKSRC_COUNTER << BF_CLKSRC) | /* Operating mode is counter. */ 3249 (CLKPOL_POS << BF_CLKPOL) | /* Active high clock. */ 3250 (CNTDIR_UP << BF_CLKPOL) | /* Count direction is up. */ 3251 (CLKMULT_1X << BF_CLKMULT) | /* Clock multiplier is 1x. */ 3252 (CLKENAB_INDEX << BF_CLKENAB); /* Enabled by index */ 3253 3254 /* Disable all counter interrupts and clear any captured counter events. */ 3255 for (chan = 0; chan < S626_ENCODER_CHANNELS; chan++) { 3256 k = &encpriv[chan]; 3257 k->SetMode(dev, k, Setup, TRUE); 3258 k->SetIntSrc(dev, k, 0); 3259 k->ResetCapFlags(dev, k); 3260 k->SetEnable(dev, k, CLKENAB_ALWAYS); 3261 } 3262 DEBUG("CountersInit: counters initialized \n"); 3263 3264} 3265