1/****************************************************************************** 2 * 3 * Copyright (C) 2003-2014 Broadcom Corporation 4 * 5 * Licensed under the Apache License, Version 2.0 (the "License"); 6 * you may not use this file except in compliance with the License. 7 * You may obtain a copy of the License at: 8 * 9 * http://www.apache.org/licenses/LICENSE-2.0 10 * 11 * Unless required by applicable law or agreed to in writing, software 12 * distributed under the License is distributed on an "AS IS" BASIS, 13 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. 14 * See the License for the specific language governing permissions and 15 * limitations under the License. 16 * 17 ******************************************************************************/ 18 19/****************************************************************************** 20 * 21 * This is the public interface file for BTA, Broadcom's Bluetooth 22 * application layer for mobile phones. 23 * 24 ******************************************************************************/ 25#ifndef BTA_API_H 26#define BTA_API_H 27 28#include "data_types.h" 29#include "bt_target.h" 30#include "bt_types.h" 31#include "btm_api.h" 32#include "uipc_msg.h" 33 34#if BLE_INCLUDED == TRUE 35#include "btm_ble_api.h" 36#endif 37 38/***************************************************************************** 39** Constants and data types 40*****************************************************************************/ 41 42/* Status Return Value */ 43#define BTA_SUCCESS 0 /* Successful operation. */ 44#define BTA_FAILURE 1 /* Generic failure. */ 45#define BTA_PENDING 2 /* API cannot be completed right now */ 46#define BTA_BUSY 3 47#define BTA_NO_RESOURCES 4 48#define BTA_WRONG_MODE 5 49 50typedef UINT8 tBTA_STATUS; 51 52/* 53 * Service ID 54 * 55 * NOTES: When you add a new Service ID for BTA AND require to change the value of BTA_MAX_SERVICE_ID, 56 * make sure that the correct security ID of the new service from Security service definitions (btm_api.h) 57 * should be added to bta_service_id_to_btm_srv_id_lkup_tbl table in bta_dm_act.c. 58 */ 59 60#define BTA_RES_SERVICE_ID 0 /* Reserved */ 61#define BTA_SPP_SERVICE_ID 1 /* Serial port profile. */ 62#define BTA_DUN_SERVICE_ID 2 /* Dial-up networking profile. */ 63#define BTA_A2DP_SOURCE_SERVICE_ID 3 /* A2DP Source profile. */ 64#define BTA_LAP_SERVICE_ID 4 /* LAN access profile. */ 65#define BTA_HSP_SERVICE_ID 5 /* Headset profile. */ 66#define BTA_HFP_SERVICE_ID 6 /* Hands-free profile. */ 67#define BTA_OPP_SERVICE_ID 7 /* Object push */ 68#define BTA_FTP_SERVICE_ID 8 /* File transfer */ 69#define BTA_CTP_SERVICE_ID 9 /* Cordless Terminal */ 70#define BTA_ICP_SERVICE_ID 10 /* Intercom Terminal */ 71#define BTA_SYNC_SERVICE_ID 11 /* Synchronization */ 72#define BTA_BPP_SERVICE_ID 12 /* Basic printing profile */ 73#define BTA_BIP_SERVICE_ID 13 /* Basic Imaging profile */ 74#define BTA_PANU_SERVICE_ID 14 /* PAN User */ 75#define BTA_NAP_SERVICE_ID 15 /* PAN Network access point */ 76#define BTA_GN_SERVICE_ID 16 /* PAN Group Ad-hoc networks */ 77#define BTA_SAP_SERVICE_ID 17 /* SIM Access profile */ 78#define BTA_A2DP_SERVICE_ID 18 /* A2DP Sink */ 79#define BTA_AVRCP_SERVICE_ID 19 /* A/V remote control */ 80#define BTA_HID_SERVICE_ID 20 /* HID */ 81#define BTA_VDP_SERVICE_ID 21 /* Video distribution */ 82#define BTA_PBAP_SERVICE_ID 22 /* PhoneBook Access Server*/ 83#define BTA_HSP_HS_SERVICE_ID 23 /* HFP HS role */ 84#define BTA_HFP_HS_SERVICE_ID 24 /* HSP HS role */ 85#define BTA_MAP_SERVICE_ID 25 /* Message Access Profile */ 86#define BTA_MN_SERVICE_ID 26 /* Message Notification Service */ 87#define BTA_HDP_SERVICE_ID 27 /* Health Device Profile */ 88#define BTA_PCE_SERVICE_ID 28 /* PhoneBook Access Client*/ 89 90#if BLE_INCLUDED == TRUE && BTA_GATT_INCLUDED == TRUE 91/* BLE profile service ID */ 92#define BTA_BLE_SERVICE_ID 29 /* GATT profile */ 93 94// btla-specific ++ 95#define BTA_USER_SERVICE_ID 30 /* User requested UUID */ 96 97#define BTA_MAX_SERVICE_ID 31 98// btla-specific -- 99#else 100#define BTA_USER_SERVICE_ID 29 /* User requested UUID */ 101#define BTA_MAX_SERVICE_ID 30 102#endif 103/* service IDs (BTM_SEC_SERVICE_FIRST_EMPTY + 1) to (BTM_SEC_MAX_SERVICES - 1) 104 * are used by BTA JV */ 105#define BTA_FIRST_JV_SERVICE_ID (BTM_SEC_SERVICE_FIRST_EMPTY + 1) 106#define BTA_LAST_JV_SERVICE_ID (BTM_SEC_MAX_SERVICES - 1) 107 108typedef UINT8 tBTA_SERVICE_ID; 109 110/* Service ID Mask */ 111#define BTA_RES_SERVICE_MASK 0x00000001 /* Reserved */ 112#define BTA_SPP_SERVICE_MASK 0x00000002 /* Serial port profile. */ 113#define BTA_DUN_SERVICE_MASK 0x00000004 /* Dial-up networking profile. */ 114#define BTA_FAX_SERVICE_MASK 0x00000008 /* Fax profile. */ 115#define BTA_LAP_SERVICE_MASK 0x00000010 /* LAN access profile. */ 116#define BTA_HSP_SERVICE_MASK 0x00000020 /* HSP AG role. */ 117#define BTA_HFP_SERVICE_MASK 0x00000040 /* HFP AG role */ 118#define BTA_OPP_SERVICE_MASK 0x00000080 /* Object push */ 119#define BTA_FTP_SERVICE_MASK 0x00000100 /* File transfer */ 120#define BTA_CTP_SERVICE_MASK 0x00000200 /* Cordless Terminal */ 121#define BTA_ICP_SERVICE_MASK 0x00000400 /* Intercom Terminal */ 122#define BTA_SYNC_SERVICE_MASK 0x00000800 /* Synchronization */ 123#define BTA_BPP_SERVICE_MASK 0x00001000 /* Print server */ 124#define BTA_BIP_SERVICE_MASK 0x00002000 /* Basic Imaging */ 125#define BTA_PANU_SERVICE_MASK 0x00004000 /* PAN User */ 126#define BTA_NAP_SERVICE_MASK 0x00008000 /* PAN Network access point */ 127#define BTA_GN_SERVICE_MASK 0x00010000 /* PAN Group Ad-hoc networks */ 128#define BTA_SAP_SERVICE_MASK 0x00020000 /* PAN Group Ad-hoc networks */ 129#define BTA_A2DP_SERVICE_MASK 0x00040000 /* Advanced audio distribution */ 130#define BTA_AVRCP_SERVICE_MASK 0x00080000 /* A/V remote control */ 131#define BTA_HID_SERVICE_MASK 0x00100000 /* HID */ 132#define BTA_VDP_SERVICE_MASK 0x00200000 /* Video distribution */ 133#define BTA_PBAP_SERVICE_MASK 0x00400000 /* Phone Book Server */ 134#define BTA_HSP_HS_SERVICE_MASK 0x00800000 /* HFP HS role */ 135#define BTA_HFP_HS_SERVICE_MASK 0x01000000 /* HSP HS role */ 136#define BTA_MAS_SERVICE_MASK 0x02000000 /* Message Access Profile */ 137#define BTA_MN_SERVICE_MASK 0x04000000 /* Message Notification Profile */ 138#define BTA_HL_SERVICE_MASK 0x08000000 /* Health Device Profile */ 139#define BTA_PCE_SERVICE_MASK 0x10000000 /* Phone Book Client */ 140 141#if BLE_INCLUDED == TRUE && BTA_GATT_INCLUDED == TRUE 142#define BTA_BLE_SERVICE_MASK 0x20000000 /* GATT based service */ 143// btla-specific ++ 144#define BTA_USER_SERVICE_MASK 0x40000000 /* Message Notification Profile */ 145// btla-specific -- 146#else 147// btla-specific ++ 148#define BTA_USER_SERVICE_MASK 0x20000000 /* Message Notification Profile */ 149// btla-specific -- 150#endif 151 152#if BLE_INCLUDED == TRUE && BTA_GATT_INCLUDED == TRUE 153#define BTA_ALL_SERVICE_MASK 0x3FFFFFFF /* All services supported by BTA. */ 154#else 155#define BTA_ALL_SERVICE_MASK 0x1FFFFFFF /* All services supported by BTA. */ 156#endif 157 158typedef UINT32 tBTA_SERVICE_MASK; 159 160/* extended service mask, including mask with one or more GATT UUID */ 161typedef struct 162{ 163 tBTA_SERVICE_MASK srvc_mask; 164 UINT8 num_uuid; 165 tBT_UUID *p_uuid; 166}tBTA_SERVICE_MASK_EXT; 167 168/* Security Setting Mask */ 169#define BTA_SEC_NONE BTM_SEC_NONE /* No security. */ 170#define BTA_SEC_AUTHORIZE (BTM_SEC_IN_AUTHORIZE ) /* Authorization required (only needed for out going connection )*/ 171#define BTA_SEC_AUTHENTICATE (BTM_SEC_IN_AUTHENTICATE | BTM_SEC_OUT_AUTHENTICATE) /* Authentication required. */ 172#define BTA_SEC_ENCRYPT (BTM_SEC_IN_ENCRYPT | BTM_SEC_OUT_ENCRYPT) /* Encryption required. */ 173 174typedef UINT8 tBTA_SEC; 175 176/* Ignore for Discoverable, Connectable, Pairable and Connectable Paired only device modes */ 177 178#define BTA_DM_IGNORE 0xFF 179 180#define BTA_ALL_APP_ID 0xFF 181 182/* Discoverable Modes */ 183#define BTA_DM_NON_DISC BTM_NON_DISCOVERABLE /* Device is not discoverable. */ 184#define BTA_DM_GENERAL_DISC BTM_GENERAL_DISCOVERABLE /* General discoverable. */ 185#define BTA_DM_LIMITED_DISC BTM_LIMITED_DISCOVERABLE /* Limited discoverable. */ 186#if ((defined BLE_INCLUDED) && (BLE_INCLUDED == TRUE)) 187#define BTA_DM_BLE_NON_DISCOVERABLE BTM_BLE_NON_DISCOVERABLE /* Device is not LE discoverable */ 188#define BTA_DM_BLE_GENERAL_DISCOVERABLE BTM_BLE_GENERAL_DISCOVERABLE /* Device is LE General discoverable */ 189#define BTA_DM_BLE_LIMITED_DISCOVERABLE BTM_BLE_LIMITED_DISCOVERABLE /* Device is LE Limited discoverable */ 190#endif 191typedef UINT16 tBTA_DM_DISC; /* this discoverability mode is a bit mask among BR mode and LE mode */ 192 193/* Connectable Modes */ 194#define BTA_DM_NON_CONN BTM_NON_CONNECTABLE /* Device is not connectable. */ 195#define BTA_DM_CONN BTM_CONNECTABLE /* Device is connectable. */ 196#if ((defined BLE_INCLUDED) && (BLE_INCLUDED == TRUE)) 197#define BTA_DM_BLE_NON_CONNECTABLE BTM_BLE_NON_CONNECTABLE /* Device is LE non-connectable. */ 198#define BTA_DM_BLE_CONNECTABLE BTM_BLE_CONNECTABLE /* Device is LE connectable. */ 199#endif 200 201// btla-specific ++ 202typedef UINT16 tBTA_DM_CONN; 203 204#define BTA_TRANSPORT_UNKNOWN 0 205#define BTA_TRANSPORT_BR_EDR BT_TRANSPORT_BR_EDR 206#define BTA_TRANSPORT_LE BT_TRANSPORT_LE 207typedef tBT_TRANSPORT tBTA_TRANSPORT; 208 209/* Pairable Modes */ 210#define BTA_DM_PAIRABLE 1 211#define BTA_DM_NON_PAIRABLE 0 212 213/* Connectable Paired Only Mode */ 214#define BTA_DM_CONN_ALL 0 215#define BTA_DM_CONN_PAIRED 1 216 217/* Inquiry Modes */ 218#define BTA_DM_INQUIRY_NONE BTM_INQUIRY_NONE /*No BR inquiry. */ 219#define BTA_DM_GENERAL_INQUIRY BTM_GENERAL_INQUIRY /* Perform general inquiry. */ 220#define BTA_DM_LIMITED_INQUIRY BTM_LIMITED_INQUIRY /* Perform limited inquiry. */ 221 222#if ((defined BLE_INCLUDED) && (BLE_INCLUDED == TRUE)) 223#define BTA_BLE_INQUIRY_NONE BTM_BLE_INQUIRY_NONE 224#define BTA_BLE_GENERAL_INQUIRY BTM_BLE_GENERAL_INQUIRY /* Perform LE general inquiry. */ 225#define BTA_BLE_LIMITED_INQUIRY BTM_BLE_LIMITED_INQUIRY /* Perform LE limited inquiry. */ 226#endif 227typedef UINT8 tBTA_DM_INQ_MODE; 228 229/* Inquiry Filter Type */ 230#define BTA_DM_INQ_CLR BTM_CLR_INQUIRY_FILTER /* Clear inquiry filter. */ 231#define BTA_DM_INQ_DEV_CLASS BTM_FILTER_COND_DEVICE_CLASS /* Filter on device class. */ 232#define BTA_DM_INQ_BD_ADDR BTM_FILTER_COND_BD_ADDR /* Filter on a specific BD address. */ 233 234typedef UINT8 tBTA_DM_INQ_FILT; 235 236/* Authorize Response */ 237#define BTA_DM_AUTH_PERM 0 /* Authorized for future connections to the service */ 238#define BTA_DM_AUTH_TEMP 1 /* Authorized for current connection only */ 239#define BTA_DM_NOT_AUTH 2 /* Not authorized for the service */ 240 241typedef UINT8 tBTA_AUTH_RESP; 242 243/* M/S preferred roles */ 244#define BTA_ANY_ROLE 0x00 245#define BTA_MASTER_ROLE_PREF 0x01 246#define BTA_MASTER_ROLE_ONLY 0x02 247 248typedef UINT8 tBTA_PREF_ROLES; 249 250enum 251{ 252 253 BTA_DM_NO_SCATTERNET, /* Device doesn't support scatternet, it might 254 support "role switch during connection" for 255 an incoming connection, when it already has 256 another connection in master role */ 257 BTA_DM_PARTIAL_SCATTERNET, /* Device supports partial scatternet. It can have 258 simulateous connection in Master and Slave roles 259 for short period of time */ 260 BTA_DM_FULL_SCATTERNET /* Device can have simultaneous connection in master 261 and slave roles */ 262 263}; 264 265 266/* Inquiry filter device class condition */ 267typedef struct 268{ 269 DEV_CLASS dev_class; /* device class of interest */ 270 DEV_CLASS dev_class_mask; /* mask to determine the bits of device class of interest */ 271} tBTA_DM_COD_COND; 272 273 274/* Inquiry Filter Condition */ 275typedef union 276{ 277 BD_ADDR bd_addr; /* BD address of device to filter. */ 278 tBTA_DM_COD_COND dev_class_cond; /* Device class filter condition */ 279} tBTA_DM_INQ_COND; 280 281/* Inquiry Parameters */ 282typedef struct 283{ 284 tBTA_DM_INQ_MODE mode; /* Inquiry mode, limited or general. */ 285 UINT8 duration; /* Inquiry duration in 1.28 sec units. */ 286 UINT8 max_resps; /* Maximum inquiry responses. Set to zero for unlimited responses. */ 287 BOOLEAN report_dup; /* report duplicated inquiry response with higher RSSI value */ 288 tBTA_DM_INQ_FILT filter_type; /* Filter condition type. */ 289 tBTA_DM_INQ_COND filter_cond; /* Filter condition data. */ 290#if (defined(BTA_HOST_INTERLEAVE_SEARCH) && BTA_HOST_INTERLEAVE_SEARCH == TRUE) 291 UINT8 intl_duration[4];/*duration array storing the interleave scan's time portions*/ 292#endif 293} tBTA_DM_INQ; 294 295typedef struct 296{ 297 UINT8 bta_dm_eir_min_name_len; /* minimum length of local name when it is shortened */ 298#if (BTA_EIR_CANNED_UUID_LIST == TRUE) 299 UINT8 bta_dm_eir_uuid16_len; /* length of 16-bit UUIDs */ 300 UINT8 *bta_dm_eir_uuid16; /* 16-bit UUIDs */ 301#else 302 UINT32 uuid_mask[BTM_EIR_SERVICE_ARRAY_SIZE]; /* mask of UUID list in EIR */ 303#endif 304 INT8 *bta_dm_eir_inq_tx_power; /* Inquiry TX power */ 305 UINT8 bta_dm_eir_flag_len; /* length of flags in bytes */ 306 UINT8 *bta_dm_eir_flags; /* flags for EIR */ 307 UINT8 bta_dm_eir_manufac_spec_len; /* length of manufacturer specific in bytes */ 308 UINT8 *bta_dm_eir_manufac_spec; /* manufacturer specific */ 309 UINT8 bta_dm_eir_additional_len; /* length of additional data in bytes */ 310 UINT8 *bta_dm_eir_additional; /* additional data */ 311} tBTA_DM_EIR_CONF; 312 313#if BLE_INCLUDED == TRUE 314/* ADV data flag bit definition used for BTM_BLE_AD_TYPE_FLAG */ 315#define BTA_BLE_LIMIT_DISC_FLAG BTM_BLE_LIMIT_DISC_FLAG 316#define BTA_BLE_GEN_DISC_FLAG BTM_BLE_GEN_DISC_FLAG 317#define BTA_BLE_BREDR_NOT_SPT BTM_BLE_BREDR_NOT_SPT 318#define BTA_BLE_DMT_CONTROLLER_SPT BTM_BLE_DMT_CONTROLLER_SPT 319#define BTA_BLE_DMT_HOST_SPT BTM_BLE_DMT_HOST_SPT 320#define BTA_BLE_NON_LIMIT_DISC_FLAG BTM_BLE_NON_LIMIT_DISC_FLAG 321#define BTA_BLE_ADV_FLAG_MASK BTM_BLE_ADV_FLAG_MASK 322#define BTA_BLE_LIMIT_DISC_MASK BTM_BLE_LIMIT_DISC_MASK 323 324/* ADV data bit mask */ 325#define BTA_BLE_AD_BIT_DEV_NAME BTM_BLE_AD_BIT_DEV_NAME 326#define BTA_BLE_AD_BIT_FLAGS BTM_BLE_AD_BIT_FLAGS 327#define BTA_BLE_AD_BIT_MANU BTM_BLE_AD_BIT_MANU 328#define BTA_BLE_AD_BIT_TX_PWR BTM_BLE_AD_BIT_TX_PWR 329#define BTA_BLE_AD_BIT_INT_RANGE BTM_BLE_AD_BIT_INT_RANGE 330#define BTA_BLE_AD_BIT_SERVICE BTM_BLE_AD_BIT_SERVICE 331#define BTA_BLE_AD_BIT_APPEARANCE BTM_BLE_AD_BIT_APPEARANCE 332#define BTA_BLE_AD_BIT_PROPRIETARY BTM_BLE_AD_BIT_PROPRIETARY 333#define BTA_DM_BLE_AD_BIT_SERVICE_SOL BTM_BLE_AD_BIT_SERVICE_SOL 334#define BTA_DM_BLE_AD_BIT_SERVICE_DATA BTM_BLE_AD_BIT_SERVICE_DATA 335#define BTA_DM_BLE_AD_BIT_SIGN_DATA BTM_BLE_AD_BIT_SIGN_DATA 336#define BTA_DM_BLE_AD_BIT_SERVICE_128SOL BTM_BLE_AD_BIT_SERVICE_128SOL 337#define BTA_DM_BLE_AD_BIT_PUBLIC_ADDR BTM_BLE_AD_BIT_PUBLIC_ADDR 338#define BTA_DM_BLE_AD_BIT_RANDOM_ADDR BTM_BLE_AD_BIT_RANDOM_ADDR 339#define BTA_DM_BLE_AD_BIT_SERVICE_128 BTM_BLE_AD_BIT_SERVICE_128 /*128-bit Service UUIDs*/ 340 341typedef tBTM_BLE_AD_MASK tBTA_BLE_AD_MASK; 342 343/* slave preferred connection interval range */ 344typedef struct 345{ 346 UINT16 low; 347 UINT16 hi; 348 349}tBTA_BLE_INT_RANGE; 350 351/* Service tag supported in the device */ 352typedef struct 353{ 354 UINT8 num_service; 355 BOOLEAN list_cmpl; 356 UINT16 *p_uuid; 357}tBTA_BLE_SERVICE; 358 359 360typedef struct 361{ 362 UINT8 len; 363 UINT8 *p_val; 364}tBTA_BLE_MANU; 365 366typedef struct 367{ 368 UINT8 adv_type; 369 UINT8 len; 370 UINT8 *p_val; /* number of len byte */ 371}tBTA_BLE_PROP_ELEM; 372 373/* vendor proprietary adv type */ 374typedef struct 375{ 376 UINT8 num_elem; 377 tBTA_BLE_PROP_ELEM *p_elem; 378}tBTA_BLE_PROPRIETARY; 379 380typedef struct 381{ 382 tBT_UUID service_uuid; 383 UINT8 len; 384 UINT8 *p_val; 385}tBTA_BLE_SERVICE_DATA; 386 387typedef tBTM_BLE_128SERVICE tBTA_BLE_128SERVICE; 388typedef tBTM_BLE_32SERVICE tBTA_BLE_32SERVICE; 389 390typedef struct 391{ 392 tBTA_BLE_INT_RANGE int_range; /* slave prefered conn interval range */ 393 tBTA_BLE_MANU *p_manu; /* manufacturer data */ 394 tBTA_BLE_SERVICE *p_services; /* 16 bits services */ 395 tBTA_BLE_128SERVICE *p_services_128b; /* 128 bits service */ 396 tBTA_BLE_32SERVICE *p_service_32b; /* 32 bits Service UUID */ 397 tBTA_BLE_SERVICE *p_sol_services; /* 16 bits services Solicitation UUIDs */ 398 tBTA_BLE_32SERVICE *p_sol_service_32b; /* List of 32 bit Service Solicitation UUIDs */ 399 tBTA_BLE_128SERVICE *p_sol_service_128b;/* List of 128 bit Service Solicitation UUIDs */ 400 tBTA_BLE_PROPRIETARY *p_proprietary; /* proprietary data */ 401 tBTA_BLE_SERVICE_DATA *p_service_data; /* service data */ 402 UINT16 appearance; /* appearance data */ 403 UINT8 flag; 404 UINT8 tx_power; 405}tBTA_BLE_ADV_DATA; 406 407typedef void (tBTA_SET_ADV_DATA_CMPL_CBACK) (tBTA_STATUS status); 408 409/* advertising channel map */ 410#define BTA_BLE_ADV_CHNL_37 BTM_BLE_ADV_CHNL_37 411#define BTA_BLE_ADV_CHNL_38 BTM_BLE_ADV_CHNL_38 412#define BTA_BLE_ADV_CHNL_39 BTM_BLE_ADV_CHNL_39 413typedef tBTM_BLE_ADV_CHNL_MAP tBTA_BLE_ADV_CHNL_MAP; /* use as a bit mask */ 414 415/* advertising filter policy */ 416typedef tBTM_BLE_AFP tBTA_BLE_AFP; 417 418/* adv event type */ 419#define BTA_BLE_CONNECT_EVT BTM_BLE_CONNECT_EVT /* Connectable undirected advertising */ 420#define BTA_BLE_CONNECT_DIR_EVT BTM_BLE_CONNECT_DIR_EVT /* Connectable directed advertising */ 421#define BTA_BLE_DISCOVER_EVT BTM_BLE_DISCOVER_EVT /* Scannable undirected advertising */ 422#define BTA_BLE_NON_CONNECT_EVT BTM_BLE_NON_CONNECT_EVT /* Non connectable undirected advertising */ 423typedef UINT8 tBTA_BLE_ADV_EVT; 424 425/* adv tx power level */ 426#define BTA_BLE_ADV_TX_POWER_MIN 0 /* minimum tx power */ 427#define BTA_BLE_ADV_TX_POWER_LOW 1 /* low tx power */ 428#define BTA_BLE_ADV_TX_POWER_MID 2 /* middle tx power */ 429#define BTA_BLE_ADV_TX_POWER_UPPER 3 /* upper tx power */ 430#define BTA_BLE_ADV_TX_POWER_MAX 4 /* maximum tx power */ 431typedef UINT8 tBTA_BLE_ADV_TX_POWER; 432 433/* advertising instance parameters */ 434typedef struct 435{ 436 UINT16 adv_int_min; /* minimum adv interval */ 437 UINT16 adv_int_max; /* maximum adv interval */ 438 tBTA_BLE_ADV_EVT adv_type; /* adv event type */ 439 tBTA_BLE_ADV_CHNL_MAP channel_map; /* adv channel map */ 440 tBTA_BLE_AFP adv_filter_policy; /* advertising filter policy */ 441 tBTA_BLE_ADV_TX_POWER tx_power; /* adv tx power */ 442}tBTA_BLE_ADV_PARAMS; 443 444/* These are the fields returned in each device adv packet. It 445** is returned in the results callback if registered. 446*/ 447typedef struct 448{ 449 UINT8 conn_mode; 450 tBTA_BLE_AD_MASK ad_mask; /* mask of the valid adv data field */ 451 UINT8 flag; 452 UINT8 tx_power_level; 453 UINT8 remote_name_len; 454 UINT8 *p_remote_name; 455 tBTA_BLE_SERVICE service; 456} tBTA_BLE_INQ_DATA; 457 458enum 459{ 460 BTA_BLE_SCAN_MODE_PASS=1, 461 BTA_BLE_SCAN_MODE_ACTI=2, 462 BTA_BLE_SCAN_MODE_PASS_ACTI=3 463}; 464typedef UINT8 tBTA_BLE_SCAN_MODE; 465 466enum 467{ 468 BTA_BLE_DISCARD_OLD_ITEMS=0, 469 BTA_BLE_DISCARD_LOWER_RSSI_ITEMS=1 470}; 471typedef UINT8 tBTA_BLE_DISCARD_RULE; 472 473enum 474{ 475 BTA_BLE_ADV_SEEN_FIRST_TIME=0, 476 BTA_BLE_ADV_TRACKING_TIMEOUT=1 477}; 478typedef UINT8 tBTA_BLE_ADV_CHANGE_REASON; 479 480enum 481{ 482 BTA_BLE_BATCH_SCAN_ENB_EVT = 1, 483 BTA_BLE_BATCH_SCAN_CFG_STRG_EVT = 2, 484 BTA_BLE_BATCH_SCAN_DATA_EVT = 3, 485 BTA_BLE_BATCH_SCAN_THRES_EVT = 4, 486 BTA_BLE_BATCH_SCAN_PARAM_EVT = 5, 487 BTA_BLE_BATCH_SCAN_DIS_EVT = 6 488}; 489typedef tBTM_BLE_BATCH_SCAN_EVT tBTA_BLE_BATCH_SCAN_EVT; 490 491typedef tBTM_BLE_TRACK_ADV_ACTION tBTA_BLE_TRACK_ADV_ACTION; 492#endif 493 494/* BLE customer specific feature function type definitions */ 495/* data type used on customer specific feature for RSSI monitoring */ 496#define BTA_BLE_RSSI_ALERT_HI 0 497#define BTA_BLE_RSSI_ALERT_RANGE 1 498#define BTA_BLE_RSSI_ALERT_LO 2 499typedef UINT8 tBTA_DM_BLE_RSSI_ALERT_TYPE; 500 501#define BTA_BLE_RSSI_ALERT_NONE BTM_BLE_RSSI_ALERT_NONE /* (0) */ 502#define BTA_BLE_RSSI_ALERT_HI_BIT BTM_BLE_RSSI_ALERT_HI_BIT /* (1) */ 503#define BTA_BLE_RSSI_ALERT_RANGE_BIT BTM_BLE_RSSI_ALERT_RANGE_BIT /* (1 << 1) */ 504#define BTA_BLE_RSSI_ALERT_LO_BIT BTM_BLE_RSSI_ALERT_LO_BIT /* (1 << 2) */ 505typedef UINT8 tBTA_DM_BLE_RSSI_ALERT_MASK; 506 507 508typedef void (tBTA_DM_BLE_RSSI_CBACK) (BD_ADDR bd_addr, tBTA_DM_BLE_RSSI_ALERT_TYPE alert_type, INT8 rssi); 509 510/* max number of filter spot for different filter type */ 511#define BTA_DM_BLE_MAX_UUID_FILTER BTM_BLE_MAX_UUID_FILTER /* 8 */ 512#define BTA_DM_BLE_MAX_ADDR_FILTER BTM_BLE_MAX_ADDR_FILTER /* 8 */ 513#define BTA_DM_BLE_PF_STR_COND_MAX BTM_BLE_PF_STR_COND_MAX /* 4 apply to manu data , or local name */ 514#define BTA_DM_BLE_PF_STR_LEN_MAX BTM_BLE_PF_STR_LEN_MAX /* match for first 20 bytes */ 515 516#define BTA_DM_BLE_PF_LOGIC_OR 0 517#define BTA_DM_BLE_PF_LOGIC_AND 1 518typedef UINT8 tBTA_DM_BLE_PF_LOGIC_TYPE; 519 520enum 521{ 522 BTA_DM_BLE_SCAN_COND_ADD, 523 BTA_DM_BLE_SCAN_COND_DELETE, 524 BTA_DM_BLE_SCAN_COND_CLEAR = 2 525}; 526typedef UINT8 tBTA_DM_BLE_SCAN_COND_OP; 527 528/* ADV payload filtering vendor specific call event */ 529enum 530{ 531 BTA_BLE_SCAN_PF_ENABLE_EVT = 7, 532 BTA_BLE_SCAN_PF_COND_EVT 533}; 534 535/* filter selection bit index */ 536#define BTA_DM_BLE_PF_ADDR_FILTER BTM_BLE_PF_ADDR_FILTER 537#define BTA_DM_BLE_PF_SRVC_DATA BTM_BLE_PF_SRVC_DATA 538#define BTA_DM_BLE_PF_SRVC_UUID BTM_BLE_PF_SRVC_UUID 539#define BTA_DM_BLE_PF_SRVC_SOL_UUID BTM_BLE_PF_SRVC_SOL_UUID 540#define BTA_DM_BLE_PF_LOCAL_NAME BTM_BLE_PF_LOCAL_NAME 541#define BTA_DM_BLE_PF_MANU_DATA BTM_BLE_PF_MANU_DATA 542#define BTA_DM_BLE_PF_SRVC_DATA_PATTERN BTM_BLE_PF_SRVC_DATA_PATTERN 543#define BTA_DM_BLE_PF_TYPE_ALL BTM_BLE_PF_TYPE_ALL 544#define BTA_DM_BLE_PF_TYPE_MAX BTM_BLE_PF_TYPE_MAX 545typedef UINT8 tBTA_DM_BLE_PF_COND_TYPE; 546 547typedef union 548{ 549 UINT16 uuid16_mask; 550 UINT32 uuid32_mask; 551 UINT8 uuid128_mask[LEN_UUID_128]; 552}tBTA_DM_BLE_PF_COND_MASK; 553 554typedef struct 555{ 556 tBLE_BD_ADDR *p_target_addr; /* target address, if NULL, generic UUID filter */ 557 tBT_UUID uuid; /* UUID condition */ 558 tBTA_DM_BLE_PF_LOGIC_TYPE cond_logic; /* AND/OR */ 559 tBTA_DM_BLE_PF_COND_MASK *p_uuid_mask; /* UUID condition mask, if NULL, match exact as UUID condition */ 560}tBTA_DM_BLE_PF_UUID_COND; 561 562typedef struct 563{ 564 UINT8 data_len; /* <= 20 bytes */ 565 UINT8 *p_data; 566}tBTA_DM_BLE_PF_LOCAL_NAME_COND; 567 568typedef struct 569{ 570 UINT16 company_id; /* company ID */ 571 UINT8 data_len; /* <= 20 bytes */ 572 UINT8 *p_pattern; 573 UINT16 company_id_mask; /* UUID value mask */ 574 UINT8 *p_pattern_mask; /* Manufacturer data matching mask, same length 575 as data pattern, set to all 0xff, match exact data */ 576}tBTA_DM_BLE_PF_MANU_COND; 577 578typedef struct 579{ 580 UINT16 uuid; /* service ID */ 581 UINT8 data_len; /* <= 20 bytes */ 582 UINT8 *p_pattern; 583 UINT8 *p_pattern_mask; /* Service data matching mask, same length 584 as data pattern, set to all 0xff, match exact data */ 585}tBTA_DM_BLE_PF_SRVC_PATTERN_COND; 586 587typedef union 588{ 589 tBLE_BD_ADDR target_addr; 590 tBTA_DM_BLE_PF_LOCAL_NAME_COND local_name; /* lcoal name filtering */ 591 tBTA_DM_BLE_PF_MANU_COND manu_data; /* manufactuer data filtering */ 592 tBTA_DM_BLE_PF_UUID_COND srvc_uuid; /* service UUID filtering */ 593 tBTA_DM_BLE_PF_UUID_COND solicitate_uuid; /* solicitated service UUID filtering */ 594 tBTA_DM_BLE_PF_SRVC_PATTERN_COND srvc_data; /* service data pattern */ 595}tBTA_DM_BLE_PF_COND_PARAM; 596 597typedef UINT8 tBTA_DM_BLE_PF_FILT_INDEX; 598typedef UINT8 tBTA_DM_BLE_PF_AVBL_SPACE; 599 600typedef INT8 tBTA_DM_RSSI_VALUE; 601typedef UINT8 tBTA_DM_LINK_QUALITY_VALUE; 602 603 604/* signal strength mask */ 605#define BTA_SIG_STRENGTH_RSSI_MASK 1 606#define BTA_SIG_STRENGTH_LINK_QUALITY_MASK 2 607 608typedef UINT8 tBTA_SIG_STRENGTH_MASK; 609 610 611/* Security Callback Events */ 612#define BTA_DM_ENABLE_EVT 0 /* Enable Event */ 613#define BTA_DM_DISABLE_EVT 1 /* Disable Event */ 614#define BTA_DM_PIN_REQ_EVT 2 /* PIN request. */ 615#define BTA_DM_AUTH_CMPL_EVT 3 /* Authentication complete indication. */ 616#define BTA_DM_AUTHORIZE_EVT 4 /* Authorization request. */ 617#define BTA_DM_LINK_UP_EVT 5 /* Connection UP event */ 618#define BTA_DM_LINK_DOWN_EVT 6 /* Connection DOWN event */ 619#define BTA_DM_SIG_STRENGTH_EVT 7 /* Signal strength for bluetooth connection */ 620#define BTA_DM_BUSY_LEVEL_EVT 8 /* System busy level */ 621#define BTA_DM_BOND_CANCEL_CMPL_EVT 9 /* Bond cancel complete indication */ 622#define BTA_DM_SP_CFM_REQ_EVT 10 /* Simple Pairing User Confirmation request. */ 623#define BTA_DM_SP_KEY_NOTIF_EVT 11 /* Simple Pairing Passkey Notification */ 624#define BTA_DM_SP_RMT_OOB_EVT 12 /* Simple Pairing Remote OOB Data request. */ 625#define BTA_DM_SP_KEYPRESS_EVT 13 /* Key press notification event. */ 626#define BTA_DM_ROLE_CHG_EVT 14 /* Role Change event. */ 627#define BTA_DM_BLE_KEY_EVT 15 /* BLE SMP key event for peer device keys */ 628#define BTA_DM_BLE_SEC_REQ_EVT 16 /* BLE SMP security request */ 629#define BTA_DM_BLE_PASSKEY_NOTIF_EVT 17 /* SMP passkey notification event */ 630#define BTA_DM_BLE_PASSKEY_REQ_EVT 18 /* SMP passkey request event */ 631#define BTA_DM_BLE_OOB_REQ_EVT 19 /* SMP OOB request event */ 632#define BTA_DM_BLE_LOCAL_IR_EVT 20 /* BLE local IR event */ 633#define BTA_DM_BLE_LOCAL_ER_EVT 21 /* BLE local ER event */ 634// btla-specific ++ 635#define BTA_DM_BLE_AUTH_CMPL_EVT 22 /* BLE Auth complete */ 636// btla-specific -- 637#define BTA_DM_DEV_UNPAIRED_EVT 23 638#define BTA_DM_HW_ERROR_EVT 24 /* BT Chip H/W error */ 639#define BTA_DM_LE_FEATURES_READ 25 /* Cotroller specific LE features are read */ 640#define BTA_DM_ENER_INFO_READ 26 /* Energy info read */ 641typedef UINT8 tBTA_DM_SEC_EVT; 642 643/* Structure associated with BTA_DM_ENABLE_EVT */ 644typedef struct 645{ 646 BD_ADDR bd_addr; /* BD address of local device. */ 647 tBTA_STATUS status; 648} tBTA_DM_ENABLE; 649 650/* Structure associated with BTA_DM_PIN_REQ_EVT */ 651typedef struct 652{ 653 /* Note: First 3 data members must be, bd_addr, dev_class, and bd_name in order */ 654 BD_ADDR bd_addr; /* BD address peer device. */ 655 DEV_CLASS dev_class; /* Class of Device */ 656 BD_NAME bd_name; /* Name of peer device. */ 657} tBTA_DM_PIN_REQ; 658 659/* BLE related definition */ 660 661#define BTA_DM_AUTH_FAIL_BASE (HCI_ERR_MAX_ERR + 10) 662#define BTA_DM_AUTH_CONVERT_SMP_CODE(x) (BTA_DM_AUTH_FAIL_BASE + (x)) 663#define BTA_DM_AUTH_SMP_PASSKEY_FAIL BTA_DM_AUTH_CONVERT_SMP_CODE (SMP_PASSKEY_ENTRY_FAIL) 664#define BTA_DM_AUTH_SMP_OOB_FAIL (BTA_DM_AUTH_FAIL_BASE + SMP_OOB_FAIL) 665#define BTA_DM_AUTH_SMP_PAIR_AUTH_FAIL (BTA_DM_AUTH_FAIL_BASE + SMP_PAIR_AUTH_FAIL) 666#define BTA_DM_AUTH_SMP_CONFIRM_VALUE_FAIL (BTA_DM_AUTH_FAIL_BASE + SMP_CONFIRM_VALUE_ERR) 667#define BTA_DM_AUTH_SMP_PAIR_NOT_SUPPORT (BTA_DM_AUTH_FAIL_BASE + SMP_PAIR_NOT_SUPPORT) 668#define BTA_DM_AUTH_SMP_ENC_KEY_SIZE (BTA_DM_AUTH_FAIL_BASE + SMP_ENC_KEY_SIZE) 669#define BTA_DM_AUTH_SMP_INVALID_CMD (BTA_DM_AUTH_FAIL_BASE + SMP_INVALID_CMD) 670#define BTA_DM_AUTH_SMP_UNKNOWN_ERR (BTA_DM_AUTH_FAIL_BASE + SMP_PAIR_FAIL_UNKNOWN) 671#define BTA_DM_AUTH_SMP_REPEATED_ATTEMPT (BTA_DM_AUTH_FAIL_BASE + SMP_REPEATED_ATTEMPTS) 672#define BTA_DM_AUTH_SMP_INTERNAL_ERR (BTA_DM_AUTH_FAIL_BASE + SMP_PAIR_INTERNAL_ERR) 673#define BTA_DM_AUTH_SMP_UNKNOWN_IO (BTA_DM_AUTH_FAIL_BASE + SMP_UNKNOWN_IO_CAP) 674#define BTA_DM_AUTH_SMP_INIT_FAIL (BTA_DM_AUTH_FAIL_BASE + SMP_INIT_FAIL) 675#define BTA_DM_AUTH_SMP_CONFIRM_FAIL (BTA_DM_AUTH_FAIL_BASE + SMP_CONFIRM_FAIL) 676#define BTA_DM_AUTH_SMP_BUSY (BTA_DM_AUTH_FAIL_BASE + SMP_BUSY) 677#define BTA_DM_AUTH_SMP_ENC_FAIL (BTA_DM_AUTH_FAIL_BASE + SMP_ENC_FAIL) 678#define BTA_DM_AUTH_SMP_RSP_TIMEOUT (BTA_DM_AUTH_FAIL_BASE + SMP_RSP_TIMEOUT) 679 680/* connection parameter boundary value and dummy value */ 681#define BTA_DM_BLE_SCAN_INT_MIN BTM_BLE_SCAN_INT_MIN 682#define BTA_DM_BLE_SCAN_INT_MAX BTM_BLE_SCAN_INT_MAX 683#define BTA_DM_BLE_SCAN_WIN_MIN BTM_BLE_SCAN_WIN_MIN 684#define BTA_DM_BLE_SCAN_WIN_MAX BTM_BLE_SCAN_WIN_MAX 685#define BTA_DM_BLE_CONN_INT_MIN BTM_BLE_CONN_INT_MIN 686#define BTA_DM_BLE_CONN_INT_MAX BTM_BLE_CONN_INT_MAX 687#define BTA_DM_BLE_CONN_LATENCY_MAX BTM_BLE_CONN_LATENCY_MAX 688#define BTA_DM_BLE_CONN_SUP_TOUT_MIN BTM_BLE_CONN_SUP_TOUT_MIN 689#define BTA_DM_BLE_CONN_SUP_TOUT_MAX BTM_BLE_CONN_SUP_TOUT_MAX 690#define BTA_DM_BLE_CONN_PARAM_UNDEF BTM_BLE_CONN_PARAM_UNDEF /* use this value when a specific value not to be overwritten */ 691 692 693#define BTA_LE_KEY_PENC BTM_LE_KEY_PENC /* encryption information of peer device */ 694#define BTA_LE_KEY_PID BTM_LE_KEY_PID /* identity key of the peer device */ 695#define BTA_LE_KEY_PCSRK BTM_LE_KEY_PCSRK /* peer SRK */ 696#define BTA_LE_KEY_LENC BTM_LE_KEY_LENC /* master role security information:div */ 697#define BTA_LE_KEY_LID BTM_LE_KEY_LID /* master device ID key */ 698#define BTA_LE_KEY_LCSRK BTM_LE_KEY_LCSRK /* local CSRK has been deliver to peer */ 699typedef UINT8 tBTA_LE_KEY_TYPE; /* can be used as a bit mask */ 700 701 702typedef tBTM_LE_PENC_KEYS tBTA_LE_PENC_KEYS ; 703typedef tBTM_LE_PCSRK_KEYS tBTA_LE_PCSRK_KEYS; 704typedef tBTM_LE_LENC_KEYS tBTA_LE_LENC_KEYS ; 705typedef tBTM_LE_LCSRK_KEYS tBTA_LE_LCSRK_KEYS ; 706typedef tBTM_LE_PID_KEYS tBTA_LE_PID_KEYS ; 707 708typedef union 709{ 710 tBTA_LE_PENC_KEYS penc_key; /* received peer encryption key */ 711 tBTA_LE_PCSRK_KEYS psrk_key; /* received peer device SRK */ 712 tBTA_LE_PID_KEYS pid_key; /* peer device ID key */ 713 tBTA_LE_LENC_KEYS lenc_key; /* local encryption reproduction keys LTK = = d1(ER,DIV,0)*/ 714 tBTA_LE_LCSRK_KEYS lcsrk_key; /* local device CSRK = d1(ER,DIV,1)*/ 715}tBTA_LE_KEY_VALUE; 716 717#define BTA_BLE_LOCAL_KEY_TYPE_ID 1 718#define BTA_BLE_LOCAL_KEY_TYPE_ER 2 719typedef UINT8 tBTA_DM_BLE_LOCAL_KEY_MASK; 720 721typedef struct 722{ 723 BT_OCTET16 ir; 724 BT_OCTET16 irk; 725 BT_OCTET16 dhk; 726}tBTA_BLE_LOCAL_ID_KEYS; 727 728#define BTA_DM_SEC_GRANTED BTA_SUCCESS 729#define BTA_DM_SEC_PAIR_NOT_SPT BTA_DM_AUTH_SMP_PAIR_NOT_SUPPORT 730#define BTA_DM_SEC_REP_ATTEMPTS BTA_DM_AUTH_SMP_REPEATED_ATTEMPT 731typedef UINT8 tBTA_DM_BLE_SEC_GRANT; 732 733 734#define BTA_DM_BLE_ONN_NONE BTM_BLE_CONN_NONE 735#define BTA_DM_BLE_CONN_AUTO BTM_BLE_CONN_AUTO 736#define BTA_DM_BLE_CONN_SELECTIVE BTM_BLE_CONN_SELECTIVE 737typedef UINT8 tBTA_DM_BLE_CONN_TYPE; 738 739typedef BOOLEAN (tBTA_DM_BLE_SEL_CBACK)(BD_ADDR random_bda, UINT8 *p_remote_name); 740 741/* Structure associated with BTA_DM_BLE_SEC_REQ_EVT */ 742typedef struct 743{ 744 BD_ADDR bd_addr; /* peer address */ 745 BD_NAME bd_name; /* peer device name */ 746} tBTA_DM_BLE_SEC_REQ; 747 748typedef struct 749{ 750 BD_ADDR bd_addr; /* peer address */ 751 tBTM_LE_KEY_TYPE key_type; 752 tBTM_LE_KEY_VALUE key_value; 753}tBTA_DM_BLE_KEY; 754 755/* Structure associated with BTA_DM_AUTH_CMPL_EVT */ 756typedef struct 757{ 758 BD_ADDR bd_addr; /* BD address peer device. */ 759 BD_NAME bd_name; /* Name of peer device. */ 760 BOOLEAN key_present; /* Valid link key value in key element */ 761 LINK_KEY key; /* Link key associated with peer device. */ 762 UINT8 key_type; /* The type of Link Key */ 763 BOOLEAN success; /* TRUE of authentication succeeded, FALSE if failed. */ 764#if BLE_INCLUDED == TRUE 765 BOOLEAN privacy_enabled; /* used for BLE device only */ 766#endif 767 UINT8 fail_reason; /* The HCI reason/error code for when success=FALSE */ 768 769} tBTA_DM_AUTH_CMPL; 770 771 772/* Structure associated with BTA_DM_AUTHORIZE_EVT */ 773typedef struct 774{ 775 BD_ADDR bd_addr; /* BD address peer device. */ 776 BD_NAME bd_name; /* Name of peer device. */ 777 tBTA_SERVICE_ID service; /* Service ID to authorize. */ 778// btla-specific ++ 779 DEV_CLASS dev_class; 780// btla-specific -- 781} tBTA_DM_AUTHORIZE; 782 783/* Structure associated with BTA_DM_LINK_UP_EVT */ 784typedef struct 785{ 786 BD_ADDR bd_addr; /* BD address peer device. */ 787#if BLE_INCLUDED == TRUE 788 tBTA_TRANSPORT link_type; 789#endif 790} tBTA_DM_LINK_UP; 791 792/* Structure associated with BTA_DM_LINK_DOWN_EVT */ 793typedef struct 794{ 795 BD_ADDR bd_addr; /* BD address peer device. */ 796 UINT8 status; /* connection open/closed */ 797 BOOLEAN is_removed; /* TRUE if device is removed when link is down */ 798#if BLE_INCLUDED == TRUE 799 tBTA_TRANSPORT link_type; 800#endif 801} tBTA_DM_LINK_DOWN; 802 803/* Structure associated with BTA_DM_ROLE_CHG_EVT */ 804typedef struct 805{ 806 BD_ADDR bd_addr; /* BD address peer device. */ 807 UINT8 new_role; /* the new connection role */ 808} tBTA_DM_ROLE_CHG; 809 810/* Structure associated with BTA_DM_SIG_STRENGTH_EVT */ 811typedef struct 812{ 813 BD_ADDR bd_addr; /* BD address peer device. */ 814 tBTA_SIG_STRENGTH_MASK mask; /* mask for the values that are valid */ 815 tBTA_DM_RSSI_VALUE rssi_value; 816 tBTA_DM_LINK_QUALITY_VALUE link_quality_value; 817 818} tBTA_DM_SIG_STRENGTH; 819 820/* Structure associated with BTA_DM_BUSY_LEVEL_EVT */ 821typedef struct 822{ 823 UINT8 level; /* when paging or inquiring, level is 10. 824 Otherwise, the number of ACL links */ 825 UINT8 level_flags; /* indicates individual flags */ 826} tBTA_DM_BUSY_LEVEL; 827 828#define BTA_IO_CAP_OUT BTM_IO_CAP_OUT /* DisplayOnly */ 829#define BTA_IO_CAP_IO BTM_IO_CAP_IO /* DisplayYesNo */ 830#define BTA_IO_CAP_IN BTM_IO_CAP_IN /* KeyboardOnly */ 831#define BTA_IO_CAP_NONE BTM_IO_CAP_NONE /* NoInputNoOutput */ 832typedef tBTM_IO_CAP tBTA_IO_CAP; 833 834#define BTA_AUTH_SP_NO BTM_AUTH_SP_NO /* 0 MITM Protection Not Required - Single Profile/non-bonding 835 Numeric comparison with automatic accept allowed */ 836#define BTA_AUTH_SP_YES BTM_AUTH_SP_YES /* 1 MITM Protection Required - Single Profile/non-bonding 837 Use IO Capabilities to determine authentication procedure */ 838#define BTA_AUTH_AP_NO BTM_AUTH_AP_NO /* 2 MITM Protection Not Required - All Profiles/dedicated bonding 839 Numeric comparison with automatic accept allowed */ 840#define BTA_AUTH_AP_YES BTM_AUTH_AP_YES /* 3 MITM Protection Required - All Profiles/dedicated bonding 841 Use IO Capabilities to determine authentication procedure */ 842#define BTA_AUTH_SPGB_NO BTM_AUTH_SPGB_NO /* 4 MITM Protection Not Required - Single Profiles/general bonding 843 Numeric comparison with automatic accept allowed */ 844#define BTA_AUTH_SPGB_YES BTM_AUTH_SPGB_YES /* 5 MITM Protection Required - Single Profiles/general bonding 845 Use IO Capabilities to determine authentication procedure */ 846typedef tBTM_AUTH_REQ tBTA_AUTH_REQ; 847 848#define BTA_AUTH_DD_BOND BTM_AUTH_DD_BOND /* 2 this bit is set for dedicated bonding */ 849#define BTA_AUTH_GEN_BOND BTM_AUTH_SPGB_NO /* 4 this bit is set for general bonding */ 850#define BTA_AUTH_BONDS BTM_AUTH_BONDS /* 6 the general/dedicated bonding bits */ 851 852#define BTA_LE_AUTH_NO_BOND BTM_LE_AUTH_REQ_NO_BOND /* 0*/ 853#define BTA_LE_AUTH_BOND BTM_LE_AUTH_REQ_BOND /* 1 << 0 */ 854#define BTA_LE_AUTH_REQ_MITM BTM_LE_AUTH_REQ_MITM /* 1 << 2 */ 855typedef tBTM_LE_AUTH_REQ tBTA_LE_AUTH_REQ; /* combination of the above bit pattern */ 856 857#define BTA_OOB_NONE BTM_OOB_NONE 858#define BTA_OOB_PRESENT BTM_OOB_PRESENT 859#if BTM_OOB_INCLUDED == TRUE 860#define BTA_OOB_UNKNOWN BTM_OOB_UNKNOWN 861#endif 862typedef tBTM_OOB_DATA tBTA_OOB_DATA; 863 864/* Structure associated with BTA_DM_SP_CFM_REQ_EVT */ 865typedef struct 866{ 867 /* Note: First 3 data members must be, bd_addr, dev_class, and bd_name in order */ 868 BD_ADDR bd_addr; /* peer address */ 869 DEV_CLASS dev_class; /* peer CoD */ 870 BD_NAME bd_name; /* peer device name */ 871 UINT32 num_val; /* the numeric value for comparison. If just_works, do not show this number to UI */ 872 BOOLEAN just_works; /* TRUE, if "Just Works" association model */ 873 tBTA_AUTH_REQ loc_auth_req; /* Authentication required for local device */ 874 tBTA_AUTH_REQ rmt_auth_req; /* Authentication required for peer device */ 875 tBTA_IO_CAP loc_io_caps; /* IO Capabilities of local device */ 876 tBTA_AUTH_REQ rmt_io_caps; /* IO Capabilities of remote device */ 877} tBTA_DM_SP_CFM_REQ; 878 879enum 880{ 881 BTA_SP_KEY_STARTED, /* passkey entry started */ 882 BTA_SP_KEY_ENTERED, /* passkey digit entered */ 883 BTA_SP_KEY_ERASED, /* passkey digit erased */ 884 BTA_SP_KEY_CLEARED, /* passkey cleared */ 885 BTA_SP_KEY_COMPLT /* passkey entry completed */ 886}; 887typedef UINT8 tBTA_SP_KEY_TYPE; 888 889/* Structure associated with BTA_DM_SP_KEYPRESS_EVT */ 890typedef struct 891{ 892 BD_ADDR bd_addr; /* peer address */ 893 tBTA_SP_KEY_TYPE notif_type; 894}tBTA_DM_SP_KEY_PRESS; 895 896/* Structure associated with BTA_DM_SP_KEY_NOTIF_EVT */ 897typedef struct 898{ 899 /* Note: First 3 data members must be, bd_addr, dev_class, and bd_name in order */ 900 BD_ADDR bd_addr; /* peer address */ 901 DEV_CLASS dev_class; /* peer CoD */ 902 BD_NAME bd_name; /* peer device name */ 903 UINT32 passkey; /* the numeric value for comparison. If just_works, do not show this number to UI */ 904} tBTA_DM_SP_KEY_NOTIF; 905 906/* Structure associated with BTA_DM_SP_RMT_OOB_EVT */ 907typedef struct 908{ 909 /* Note: First 3 data members must be, bd_addr, dev_class, and bd_name in order */ 910 BD_ADDR bd_addr; /* peer address */ 911 DEV_CLASS dev_class; /* peer CoD */ 912 BD_NAME bd_name; /* peer device name */ 913} tBTA_DM_SP_RMT_OOB; 914 915/* Structure associated with BTA_DM_BOND_CANCEL_CMPL_EVT */ 916typedef struct 917{ 918 tBTA_STATUS result; /* TRUE of bond cancel succeeded, FALSE if failed. */ 919} tBTA_DM_BOND_CANCEL_CMPL; 920 921/* Union of all security callback structures */ 922typedef union 923{ 924 tBTA_DM_ENABLE enable; /* BTA enabled */ 925 tBTA_DM_PIN_REQ pin_req; /* PIN request. */ 926 tBTA_DM_AUTH_CMPL auth_cmpl; /* Authentication complete indication. */ 927 tBTA_DM_AUTHORIZE authorize; /* Authorization request. */ 928 tBTA_DM_LINK_UP link_up; /* ACL connection down event */ 929 tBTA_DM_LINK_DOWN link_down; /* ACL connection down event */ 930 tBTA_DM_SIG_STRENGTH sig_strength; /* rssi and link quality value */ 931 tBTA_DM_BUSY_LEVEL busy_level; /* System busy level */ 932 tBTA_DM_SP_CFM_REQ cfm_req; /* user confirm request */ 933 tBTA_DM_SP_KEY_NOTIF key_notif; /* passkey notification */ 934 tBTA_DM_SP_RMT_OOB rmt_oob; /* remote oob */ 935 tBTA_DM_BOND_CANCEL_CMPL bond_cancel_cmpl; /* Bond Cancel Complete indication */ 936 tBTA_DM_SP_KEY_PRESS key_press; /* key press notification event */ 937 tBTA_DM_ROLE_CHG role_chg; /* role change event */ 938 tBTA_DM_BLE_SEC_REQ ble_req; /* BLE SMP related request */ 939 tBTA_DM_BLE_KEY ble_key; /* BLE SMP keys used when pairing */ 940 tBTA_BLE_LOCAL_ID_KEYS ble_id_keys; /* IR event */ 941 BT_OCTET16 ble_er; /* ER event data */ 942} tBTA_DM_SEC; 943 944/* Security callback */ 945typedef void (tBTA_DM_SEC_CBACK)(tBTA_DM_SEC_EVT event, tBTA_DM_SEC *p_data); 946 947#define BTA_BLE_MULTI_ADV_ILLEGAL 0 948 949/* multi adv callback event */ 950#define BTA_BLE_MULTI_ADV_ENB_EVT 1 951#define BTA_BLE_MULTI_ADV_DISABLE_EVT 2 952#define BTA_BLE_MULTI_ADV_PARAM_EVT 3 953#define BTA_BLE_MULTI_ADV_DATA_EVT 4 954 955typedef UINT8 tBTA_BLE_MULTI_ADV_EVT; 956 957/* multi adv callback */ 958typedef void (tBTA_BLE_MULTI_ADV_CBACK)(tBTA_BLE_MULTI_ADV_EVT event, 959 UINT8 inst_id, void *p_ref, tBTA_STATUS status); 960typedef UINT32 tBTA_DM_BLE_REF_VALUE; 961 962#define BTA_DM_BLE_PF_ENABLE_EVT BTM_BLE_PF_ENABLE 963#define BTA_DM_BLE_PF_CONFIG_EVT BTM_BLE_PF_CONFIG 964typedef UINT8 tBTA_DM_BLE_PF_EVT; 965 966typedef UINT8 tBTA_DM_BLE_PF_COND_TYPE; 967 968#define BTA_DM_BLE_PF_LOGIC_OR 0 969#define BTA_DM_BLE_PF_LOGIC_AND 1 970typedef UINT8 tBTA_DM_BLE_PF_LOGIC_TYPE; 971 972#define BTA_DM_BLE_PF_ENABLE 1 973#define BTA_DM_BLE_PF_CONFIG 2 974typedef UINT8 tBTA_DM_BLE_PF_ACTION; 975 976typedef UINT8 tBTA_DM_BLE_PF_FILT_INDEX; 977 978typedef UINT8 tBTA_DM_BLE_PF_AVBL_SPACE; 979 980/* Config callback */ 981typedef void (tBTA_DM_BLE_PF_CFG_CBACK) (tBTA_DM_BLE_PF_ACTION action, 982 tBTA_DM_BLE_PF_COND_TYPE cfg_cond, 983 tBTA_DM_BLE_PF_AVBL_SPACE avbl_space, tBTA_STATUS status, 984 tBTA_DM_BLE_REF_VALUE ref_value); 985/* Param callback */ 986typedef void (tBTA_DM_BLE_PF_PARAM_CBACK) (UINT8 action_type, tBTA_DM_BLE_PF_AVBL_SPACE avbl_space, 987 tBTA_DM_BLE_REF_VALUE ref_value, tBTA_STATUS status); 988 989/* Status callback */ 990typedef void (tBTA_DM_BLE_PF_STATUS_CBACK) (UINT8 action, tBTA_STATUS status, 991 tBTA_DM_BLE_REF_VALUE ref_value); 992 993 994#define BTA_DM_BLE_PF_BRDCAST_ADDR_FILT 1 995#define BTA_DM_BLE_PF_SERV_DATA_CHG_FILT 2 996#define BTA_DM_BLE_PF_SERV_UUID 4 997#define BTA_DM_BLE_PF_SERV_SOLC_UUID 8 998#define BTA_DM_BLE_PF_LOC_NAME_CHECK 16 999#define BTA_DM_BLE_PF_MANUF_NAME_CHECK 32 1000#define BTA_DM_BLE_PF_SERV_DATA_CHECK 64 1001typedef UINT16 tBTA_DM_BLE_PF_FEAT_SEL; 1002 1003#define BTA_DM_BLE_PF_LIST_LOGIC_OR 1 1004#define BTA_DM_BLE_PF_LIST_LOGIC_AND 2 1005typedef UINT16 tBTA_DM_BLE_PF_LIST_LOGIC_TYPE; 1006 1007#define BTA_DM_BLE_PF_FILT_LOGIC_OR 0 1008#define BTA_DM_BLE_PF_FILT_LOGIC_AND 1 1009typedef UINT16 tBTA_DM_BLE_PF_FILT_LOGIC_TYPE; 1010 1011typedef UINT8 tBTA_DM_BLE_PF_RSSI_THRESHOLD; 1012typedef UINT8 tBTA_DM_BLE_PF_DELIVERY_MODE; 1013typedef UINT16 tBTA_DM_BLE_PF_TIMEOUT; 1014typedef UINT8 tBTA_DM_BLE_PF_TIMEOUT_CNT; 1015 1016typedef struct 1017{ 1018 tBTA_DM_BLE_PF_FEAT_SEL feat_seln; 1019 tBTA_DM_BLE_PF_LIST_LOGIC_TYPE list_logic_type; 1020 tBTA_DM_BLE_PF_FILT_LOGIC_TYPE filt_logic_type; 1021 tBTA_DM_BLE_PF_RSSI_THRESHOLD rssi_high_thres; 1022 tBTA_DM_BLE_PF_RSSI_THRESHOLD rssi_low_thres; 1023 tBTA_DM_BLE_PF_DELIVERY_MODE dely_mode; 1024 tBTA_DM_BLE_PF_TIMEOUT found_timeout; 1025 tBTA_DM_BLE_PF_TIMEOUT lost_timeout; 1026 tBTA_DM_BLE_PF_TIMEOUT_CNT found_timeout_cnt; 1027} tBTA_DM_BLE_PF_FILT_PARAMS; 1028 1029/* Vendor Specific Command Callback */ 1030typedef tBTM_VSC_CMPL_CB tBTA_VENDOR_CMPL_CBACK; 1031 1032/* Search callback events */ 1033#define BTA_DM_INQ_RES_EVT 0 /* Inquiry result for a peer device. */ 1034#define BTA_DM_INQ_CMPL_EVT 1 /* Inquiry complete. */ 1035#define BTA_DM_DISC_RES_EVT 2 /* Discovery result for a peer device. */ 1036#define BTA_DM_DISC_BLE_RES_EVT 3 /* Discovery result for BLE GATT based servoce on a peer device. */ 1037#define BTA_DM_DISC_CMPL_EVT 4 /* Discovery complete. */ 1038#define BTA_DM_DI_DISC_CMPL_EVT 5 /* Discovery complete. */ 1039#define BTA_DM_SEARCH_CANCEL_CMPL_EVT 6 /* Search cancelled */ 1040 1041typedef UINT8 tBTA_DM_SEARCH_EVT; 1042 1043#define BTA_DM_INQ_RES_IGNORE_RSSI BTM_INQ_RES_IGNORE_RSSI /* 0x7f RSSI value not supplied (ignore it) */ 1044 1045/* Structure associated with BTA_DM_INQ_RES_EVT */ 1046typedef struct 1047{ 1048 BD_ADDR bd_addr; /* BD address peer device. */ 1049 DEV_CLASS dev_class; /* Device class of peer device. */ 1050 BOOLEAN remt_name_not_required; /* Application sets this flag if it already knows the name of the device */ 1051 /* If the device name is known to application BTA skips the remote name request */ 1052 BOOLEAN is_limited; /* TRUE, if the limited inquiry bit is set in the CoD */ 1053 INT8 rssi; /* The rssi value */ 1054 UINT8 *p_eir; /* received EIR */ 1055#if (BLE_INCLUDED == TRUE) 1056 UINT8 inq_result_type; 1057 UINT8 ble_addr_type; 1058 tBTM_BLE_EVT_TYPE ble_evt_type; 1059 tBT_DEVICE_TYPE device_type; 1060 UINT8 flag; 1061#endif 1062 1063} tBTA_DM_INQ_RES; 1064 1065/* Structure associated with BTA_DM_INQ_CMPL_EVT */ 1066typedef struct 1067{ 1068 UINT8 num_resps; /* Number of inquiry responses. */ 1069} tBTA_DM_INQ_CMPL; 1070 1071/* Structure associated with BTA_DM_DI_DISC_CMPL_EVT */ 1072typedef struct 1073{ 1074 BD_ADDR bd_addr; /* BD address peer device. */ 1075 UINT8 num_record; /* Number of DI record */ 1076 tBTA_STATUS result; 1077} tBTA_DM_DI_DISC_CMPL; 1078 1079/* Structure associated with BTA_DM_DISC_RES_EVT */ 1080typedef struct 1081{ 1082 BD_ADDR bd_addr; /* BD address peer device. */ 1083 BD_NAME bd_name; /* Name of peer device. */ 1084 tBTA_SERVICE_MASK services; /* Services found on peer device. */ 1085// btla-specific ++ 1086 UINT8 * p_raw_data; /* Raw data for discovery DB */ 1087 UINT32 raw_data_size; /* size of raw data */ 1088 tBT_DEVICE_TYPE device_type; /* device type in case it is BLE device */ 1089 UINT32 num_uuids; 1090 UINT8 *p_uuid_list; 1091// btla-specific -- 1092 tBTA_STATUS result; 1093} tBTA_DM_DISC_RES; 1094 1095/* Structure associated with tBTA_DM_DISC_BLE_RES */ 1096typedef struct 1097{ 1098 BD_ADDR bd_addr; /* BD address peer device. */ 1099 BD_NAME bd_name; /* Name of peer device. */ 1100 tBT_UUID service; /* GATT based Services UUID found on peer device. */ 1101} tBTA_DM_DISC_BLE_RES; 1102 1103 1104/* Union of all search callback structures */ 1105typedef union 1106{ 1107 tBTA_DM_INQ_RES inq_res; /* Inquiry result for a peer device. */ 1108 tBTA_DM_INQ_CMPL inq_cmpl; /* Inquiry complete. */ 1109 tBTA_DM_DISC_RES disc_res; /* Discovery result for a peer device. */ 1110 tBTA_DM_DISC_BLE_RES disc_ble_res; /* discovery result for GATT based service */ 1111 tBTA_DM_DI_DISC_CMPL di_disc; /* DI discovery result for a peer device */ 1112 1113} tBTA_DM_SEARCH; 1114 1115/* Search callback */ 1116typedef void (tBTA_DM_SEARCH_CBACK)(tBTA_DM_SEARCH_EVT event, tBTA_DM_SEARCH *p_data); 1117 1118/* Execute call back */ 1119typedef void (tBTA_DM_EXEC_CBACK) (void * p_param); 1120 1121/* Encryption callback*/ 1122typedef void (tBTA_DM_ENCRYPT_CBACK) (BD_ADDR bd_addr, tBTA_TRANSPORT transport, tBTA_STATUS result); 1123 1124#if BLE_INCLUDED == TRUE 1125#define BTA_DM_BLE_SEC_NONE BTM_BLE_SEC_NONE 1126#define BTA_DM_BLE_SEC_ENCRYPT BTM_BLE_SEC_ENCRYPT 1127#define BTA_DM_BLE_SEC_NO_MITM BTM_BLE_SEC_ENCRYPT_NO_MITM 1128#define BTA_DM_BLE_SEC_MITM BTM_BLE_SEC_ENCRYPT_MITM 1129typedef tBTM_BLE_SEC_ACT tBTA_DM_BLE_SEC_ACT; 1130 1131typedef tBTM_BLE_TX_TIME_MS tBTA_DM_BLE_TX_TIME_MS; 1132typedef tBTM_BLE_RX_TIME_MS tBTA_DM_BLE_RX_TIME_MS; 1133typedef tBTM_BLE_IDLE_TIME_MS tBTA_DM_BLE_IDLE_TIME_MS; 1134typedef tBTM_BLE_ENERGY_USED tBTA_DM_BLE_ENERGY_USED; 1135 1136#define BTA_DM_CONTRL_UNKNOWN 0 /* Unknown state */ 1137#define BTA_DM_CONTRL_ACTIVE 1 /* ACL link on, SCO link ongoing, sniff mode */ 1138#define BTA_DM_CONTRL_SCAN 2 /* Scan state - paging/inquiry/trying to connect*/ 1139#define BTA_DM_CONTRL_IDLE 3 /* Idle state - page scan, LE advt, inquiry scan */ 1140 1141typedef UINT8 tBTA_DM_CONTRL_STATE; 1142 1143 1144typedef void (tBTA_BLE_SCAN_THRESHOLD_CBACK)(tBTA_DM_BLE_REF_VALUE ref_value); 1145 1146typedef void (tBTA_BLE_SCAN_REP_CBACK) (tBTA_DM_BLE_REF_VALUE ref_value, UINT8 report_format, 1147 UINT8 num_records, UINT16 data_len, 1148 UINT8* p_rep_data, tBTA_STATUS status); 1149 1150typedef void (tBTA_BLE_SCAN_SETUP_CBACK) (tBTA_BLE_BATCH_SCAN_EVT evt, 1151 tBTA_DM_BLE_REF_VALUE ref_value, 1152 tBTA_STATUS status); 1153 1154typedef void (tBTA_BLE_TRACK_ADV_CMPL_CBACK)(int action, tBTA_STATUS status, 1155 tBTA_DM_BLE_PF_AVBL_SPACE avbl_space, 1156 tBTA_DM_BLE_REF_VALUE ref_value); 1157 1158typedef void (tBTA_BLE_TRACK_ADV_CBACK)(int filt_index, tBLE_ADDR_TYPE addr_type, BD_ADDR bda, 1159 int adv_state, tBTA_DM_BLE_REF_VALUE ref_value); 1160 1161typedef void (tBTA_BLE_ENERGY_INFO_CBACK)(tBTA_DM_BLE_TX_TIME_MS tx_time, 1162 tBTA_DM_BLE_RX_TIME_MS rx_time, 1163 tBTA_DM_BLE_IDLE_TIME_MS idle_time, 1164 tBTA_DM_BLE_ENERGY_USED energy_used, 1165 tBTA_DM_CONTRL_STATE ctrl_state, 1166 tBTA_STATUS status); 1167 1168#else 1169typedef UINT8 tBTA_DM_BLE_SEC_ACT; 1170#endif 1171 1172/* Maximum service name length */ 1173#define BTA_SERVICE_NAME_LEN 35 1174#define BTA_SERVICE_DESP_LEN BTA_SERVICE_NAME_LEN 1175#define BTA_PROVIDER_NAME_LEN BTA_SERVICE_NAME_LEN 1176 1177 1178/* link policy masks */ 1179#define BTA_DM_LP_SWITCH HCI_ENABLE_MASTER_SLAVE_SWITCH 1180#define BTA_DM_LP_HOLD HCI_ENABLE_HOLD_MODE 1181#define BTA_DM_LP_SNIFF HCI_ENABLE_SNIFF_MODE 1182#define BTA_DM_LP_PARK HCI_ENABLE_PARK_MODE 1183typedef UINT16 tBTA_DM_LP_MASK; 1184 1185/* power mode actions */ 1186#define BTA_DM_PM_NO_ACTION 0x00 /* no change to the current pm setting */ 1187#define BTA_DM_PM_PARK 0x10 /* prefers park mode */ 1188#define BTA_DM_PM_SNIFF 0x20 /* prefers sniff mode */ 1189#define BTA_DM_PM_SNIFF1 0x21 /* prefers sniff1 mode */ 1190#define BTA_DM_PM_SNIFF2 0x22 /* prefers sniff2 mode */ 1191#define BTA_DM_PM_SNIFF3 0x23 /* prefers sniff3 mode */ 1192#define BTA_DM_PM_SNIFF4 0x24 /* prefers sniff4 mode */ 1193#define BTA_DM_PM_SNIFF5 0x25 /* prefers sniff5 mode */ 1194#define BTA_DM_PM_SNIFF6 0x26 /* prefers sniff6 mode */ 1195#define BTA_DM_PM_SNIFF7 0x27 /* prefers sniff7 mode */ 1196#define BTA_DM_PM_SNIFF_USER0 0x28 /* prefers user-defined sniff0 mode (testtool only) */ 1197#define BTA_DM_PM_SNIFF_USER1 0x29 /* prefers user-defined sniff1 mode (testtool only) */ 1198#define BTA_DM_PM_ACTIVE 0x40 /* prefers active mode */ 1199#define BTA_DM_PM_RETRY 0x80 /* retry power mode based on current settings */ 1200#define BTA_DM_PM_NO_PREF 0x01 /* service has no prefernce on power mode setting. eg. connection to service got closed */ 1201 1202typedef UINT8 tBTA_DM_PM_ACTTION; 1203 1204/* index to bta_dm_ssr_spec */ 1205#define BTA_DM_PM_SSR0 0 1206#define BTA_DM_PM_SSR1 1 /* BTA_DM_PM_SSR1 will be dedicated for 1207 HH SSR setting entry, no other profile can use it */ 1208#define BTA_DM_PM_SSR2 2 1209#define BTA_DM_PM_SSR3 3 1210#define BTA_DM_PM_SSR4 4 1211#define BTA_DM_PM_SSR5 5 1212#define BTA_DM_PM_SSR6 6 1213 1214#define BTA_DM_PM_NUM_EVTS 9 1215 1216#ifndef BTA_DM_PM_PARK_IDX 1217#define BTA_DM_PM_PARK_IDX 5 /* the actual index to bta_dm_pm_md[] for PARK mode */ 1218#endif 1219 1220#ifndef BTA_DM_PM_SNIFF_A2DP_IDX 1221#define BTA_DM_PM_SNIFF_A2DP_IDX BTA_DM_PM_SNIFF 1222#endif 1223 1224#ifndef BTA_DM_PM_SNIFF_HD_IDLE_IDX 1225#define BTA_DM_PM_SNIFF_HD_IDLE_IDX BTA_DM_PM_SNIFF2 1226#endif 1227 1228#ifndef BTA_DM_PM_SNIFF_SCO_OPEN_IDX 1229#define BTA_DM_PM_SNIFF_SCO_OPEN_IDX BTA_DM_PM_SNIFF3 1230#endif 1231 1232#ifndef BTA_DM_PM_SNIFF_HD_ACTIVE_IDX 1233#define BTA_DM_PM_SNIFF_HD_ACTIVE_IDX BTA_DM_PM_SNIFF4 1234#endif 1235 1236#ifndef BTA_DM_PM_SNIFF_HH_OPEN_IDX 1237#define BTA_DM_PM_SNIFF_HH_OPEN_IDX BTA_DM_PM_SNIFF2 1238#endif 1239 1240#ifndef BTA_DM_PM_SNIFF_HH_ACTIVE_IDX 1241#define BTA_DM_PM_SNIFF_HH_ACTIVE_IDX BTA_DM_PM_SNIFF2 1242#endif 1243 1244#ifndef BTA_DM_PM_SNIFF_HH_IDLE_IDX 1245#define BTA_DM_PM_SNIFF_HH_IDLE_IDX BTA_DM_PM_SNIFF2 1246#endif 1247 1248 1249#ifndef BTA_DM_PM_HH_OPEN_DELAY 1250#define BTA_DM_PM_HH_OPEN_DELAY 30000 1251#endif 1252 1253#ifndef BTA_DM_PM_HH_ACTIVE_DELAY 1254#define BTA_DM_PM_HH_ACTIVE_DELAY 30000 1255#endif 1256 1257#ifndef BTA_DM_PM_HH_IDLE_DELAY 1258#define BTA_DM_PM_HH_IDLE_DELAY 30000 1259#endif 1260 1261/* The Sniff Parameters defined below must be ordered from highest 1262 * latency (biggest interval) to lowest latency. If there is a conflict 1263 * among the connected services the setting with the lowest latency will 1264 * be selected. If a device should override a sniff parameter then it 1265 * must insure that order is maintained. 1266 */ 1267#ifndef BTA_DM_PM_SNIFF_MAX 1268#define BTA_DM_PM_SNIFF_MAX 800 1269#define BTA_DM_PM_SNIFF_MIN 400 1270#define BTA_DM_PM_SNIFF_ATTEMPT 4 1271#define BTA_DM_PM_SNIFF_TIMEOUT 1 1272#endif 1273 1274#ifndef BTA_DM_PM_SNIFF1_MAX 1275#define BTA_DM_PM_SNIFF1_MAX 400 1276#define BTA_DM_PM_SNIFF1_MIN 200 1277#define BTA_DM_PM_SNIFF1_ATTEMPT 4 1278#define BTA_DM_PM_SNIFF1_TIMEOUT 1 1279#endif 1280 1281#ifndef BTA_DM_PM_SNIFF2_MAX 1282#define BTA_DM_PM_SNIFF2_MAX 180 1283#define BTA_DM_PM_SNIFF2_MIN 150 1284#define BTA_DM_PM_SNIFF2_ATTEMPT 4 1285#define BTA_DM_PM_SNIFF2_TIMEOUT 1 1286#endif 1287 1288#ifndef BTA_DM_PM_SNIFF3_MAX 1289#define BTA_DM_PM_SNIFF3_MAX 150 1290#define BTA_DM_PM_SNIFF3_MIN 50 1291#define BTA_DM_PM_SNIFF3_ATTEMPT 4 1292#define BTA_DM_PM_SNIFF3_TIMEOUT 1 1293#endif 1294 1295#ifndef BTA_DM_PM_SNIFF4_MAX 1296#define BTA_DM_PM_SNIFF4_MAX 54 1297#define BTA_DM_PM_SNIFF4_MIN 30 1298#define BTA_DM_PM_SNIFF4_ATTEMPT 4 1299#define BTA_DM_PM_SNIFF4_TIMEOUT 1 1300#endif 1301 1302#ifndef BTA_DM_PM_PARK_MAX 1303#define BTA_DM_PM_PARK_MAX 800 1304#define BTA_DM_PM_PARK_MIN 400 1305#define BTA_DM_PM_PARK_ATTEMPT 0 1306#define BTA_DM_PM_PARK_TIMEOUT 0 1307#endif 1308 1309 1310/* Switch callback events */ 1311#define BTA_DM_SWITCH_CMPL_EVT 0 /* Completion of the Switch API */ 1312 1313typedef UINT8 tBTA_DM_SWITCH_EVT; 1314typedef void (tBTA_DM_SWITCH_CBACK)(tBTA_DM_SWITCH_EVT event, tBTA_STATUS status); 1315 1316/* Audio routing out configuration */ 1317#define BTA_DM_ROUTE_NONE 0x00 /* No Audio output */ 1318#define BTA_DM_ROUTE_DAC 0x01 /* routing over analog output */ 1319#define BTA_DM_ROUTE_I2S 0x02 /* routing over digital (I2S) output */ 1320#define BTA_DM_ROUTE_BT_MONO 0x04 /* routing over SCO */ 1321#define BTA_DM_ROUTE_BT_STEREO 0x08 /* routing over BT Stereo */ 1322#define BTA_DM_ROUTE_HOST 0x10 /* routing over Host */ 1323#define BTA_DM_ROUTE_FMTX 0x20 /* routing over FMTX */ 1324#define BTA_DM_ROUTE_FMRX 0x40 /* routing over FMRX */ 1325#define BTA_DM_ROUTE_BTSNK 0x80 /* routing over BT SNK */ 1326 1327typedef UINT8 tBTA_DM_ROUTE_PATH; 1328 1329 1330/* Device Identification (DI) data structure 1331*/ 1332/* Used to set the DI record */ 1333typedef tSDP_DI_RECORD tBTA_DI_RECORD; 1334/* Used to get the DI record */ 1335typedef tSDP_DI_GET_RECORD tBTA_DI_GET_RECORD; 1336/* SDP discovery database */ 1337typedef tSDP_DISCOVERY_DB tBTA_DISCOVERY_DB; 1338 1339#ifndef BTA_DI_NUM_MAX 1340#define BTA_DI_NUM_MAX 3 1341#endif 1342 1343/* Device features mask definitions */ 1344#define BTA_FEATURE_BYTES_PER_PAGE BTM_FEATURE_BYTES_PER_PAGE 1345#define BTA_EXT_FEATURES_PAGE_MAX BTM_EXT_FEATURES_PAGE_MAX 1346/* ACL type 1347*/ 1348#define BTA_DM_LINK_TYPE_BR_EDR 0x01 1349#define BTA_DM_LINK_TYPE_LE 0x02 1350#define BTA_DM_LINK_TYPE_ALL 0xFF 1351typedef UINT8 tBTA_DM_LINK_TYPE; 1352 1353#define IMMEDIATE_DELY_MODE 0x00 1354#define ONFOUND_DELY_MODE 0x01 1355#define BATCH_DELY_MODE 0x02 1356#define ALLOW_ALL_FILTER 0x00 1357#define LOWEST_RSSI_VALUE 129 1358 1359/***************************************************************************** 1360** External Function Declarations 1361*****************************************************************************/ 1362#ifdef __cplusplus 1363extern "C" 1364{ 1365#endif 1366 1367/******************************************************************************* 1368** 1369** Function BTA_EnableBluetooth 1370** 1371** Description This function initializes BTA and prepares BTA and the 1372** Bluetooth protocol stack for use. This function is 1373** typically called at startup or when Bluetooth services 1374** are required by the phone. This function must be called 1375** before calling any other API function. 1376** 1377** 1378** Returns BTA_SUCCESS if successful. 1379** BTA_FAIL if internal failure. 1380** 1381*******************************************************************************/ 1382BTA_API extern tBTA_STATUS BTA_EnableBluetooth(tBTA_DM_SEC_CBACK *p_cback); 1383 1384/******************************************************************************* 1385** 1386** Function BTA_DisableBluetooth 1387** 1388** Description This function disables BTA and the Bluetooth protocol 1389** stack. It is called when BTA is no longer being used 1390** by any application in the system. 1391** 1392** 1393** Returns void 1394** 1395*******************************************************************************/ 1396BTA_API extern tBTA_STATUS BTA_DisableBluetooth(void); 1397 1398/******************************************************************************* 1399** 1400** Function BTA_EnableTestMode 1401** 1402** Description Enables bluetooth device under test mode 1403** 1404** 1405** Returns tBTA_STATUS 1406** 1407*******************************************************************************/ 1408BTA_API extern tBTA_STATUS BTA_EnableTestMode(void); 1409 1410/******************************************************************************* 1411** 1412** Function BTA_DisableTestMode 1413** 1414** Description Disable bluetooth device under test mode 1415** 1416** 1417** Returns None 1418** 1419*******************************************************************************/ 1420BTA_API extern void BTA_DisableTestMode(void); 1421 1422/******************************************************************************* 1423** 1424** Function BTA_DmIsDeviceUp 1425** 1426** Description This function tests whether the Bluetooth module is up 1427** and ready. This is a direct execution function that 1428** may lock task scheduling on some platforms. 1429** 1430** 1431** Returns TRUE if the module is ready. 1432** FALSE if the module is not ready. 1433** 1434*******************************************************************************/ 1435BTA_API extern BOOLEAN BTA_DmIsDeviceUp(void); 1436 1437/******************************************************************************* 1438** 1439** Function BTA_DmSetDeviceName 1440** 1441** Description This function sets the Bluetooth name of the local device. 1442** 1443** 1444** Returns void 1445** 1446*******************************************************************************/ 1447BTA_API extern void BTA_DmSetDeviceName(char *p_name); 1448 1449/******************************************************************************* 1450** 1451** Function BTA_DmSetVisibility 1452** 1453** Description This function sets the Bluetooth connectable,discoverable, 1454** pairable and conn paired only modesmodes of the local device. 1455** This controls whether other Bluetooth devices can find and connect to 1456** the local device. 1457** 1458** 1459** Returns void 1460** 1461*******************************************************************************/ 1462BTA_API extern void BTA_DmSetVisibility(tBTA_DM_DISC disc_mode, tBTA_DM_CONN conn_mode, UINT8 pairable_mode, UINT8 conn_filter); 1463 1464/******************************************************************************* 1465** 1466** Function BTA_DmSetScanParam 1467** 1468** Description This function sets the parameters for page scan and 1469** inquiry scan. 1470** 1471** 1472** Returns void 1473** 1474*******************************************************************************/ 1475BTA_API extern void BTA_DmSetScanParam (UINT16 page_scan_interval, UINT16 page_scan_window, 1476 UINT16 inquiry_scan_interval, UINT16 inquiry_scan_window); 1477 1478/******************************************************************************* 1479** 1480** Function BTA_DmSetAfhChannels 1481** 1482** Description This function sets the AFH first and 1483** last disable channel, so channels within 1484** that range are disabled. 1485** In order to use this API, BTM_BYPASS_AMP_AUTO_AFH must be set 1486** to be TRUE 1487** 1488** Returns void 1489** 1490*******************************************************************************/ 1491BTA_API extern void BTA_DmSetAfhChannels(UINT8 first, UINT8 last); 1492 1493 1494/******************************************************************************* 1495** 1496** Function BTA_DmVendorSpecificCommand 1497** 1498** Description This function sends the vendor specific command 1499** to the controller 1500** 1501** 1502** Returns tBTA_STATUS 1503** 1504*******************************************************************************/ 1505BTA_API extern tBTA_STATUS BTA_DmVendorSpecificCommand (UINT16 opcode, UINT8 param_len,UINT8 *p_param_buf, tBTA_VENDOR_CMPL_CBACK *p_cback); 1506 1507 1508/******************************************************************************* 1509** 1510** Function BTA_DmSearch 1511** 1512** Description This function searches for peer Bluetooth devices. It 1513** first performs an inquiry; for each device found from the 1514** inquiry it gets the remote name of the device. If 1515** parameter services is nonzero, service discovery will be 1516** performed on each device for the services specified. 1517** 1518** 1519** Returns void 1520** 1521*******************************************************************************/ 1522BTA_API extern void BTA_DmSearch(tBTA_DM_INQ *p_dm_inq, tBTA_SERVICE_MASK services, 1523 tBTA_DM_SEARCH_CBACK *p_cback); 1524 1525/******************************************************************************* 1526** 1527** Function BTA_DmSearchCancel 1528** 1529** Description This function cancels a search that has been initiated 1530** by calling BTA_DmSearch(). 1531** 1532** 1533** Returns void 1534** 1535*******************************************************************************/ 1536BTA_API extern void BTA_DmSearchCancel(void); 1537 1538/******************************************************************************* 1539** 1540** Function BTA_DmDiscover 1541** 1542** Description This function performs service discovery for the services 1543** of a particular peer device. 1544** 1545** 1546** Returns void 1547** 1548*******************************************************************************/ 1549BTA_API extern void BTA_DmDiscover(BD_ADDR bd_addr, tBTA_SERVICE_MASK services, 1550 tBTA_DM_SEARCH_CBACK *p_cback, BOOLEAN sdp_search); 1551 1552// btla-specific ++ 1553/******************************************************************************* 1554** 1555** Function BTA_DmDiscoverUUID 1556** 1557** Description This function performs service discovery for the services 1558** of a particular peer device. 1559** 1560** 1561** Returns void 1562** 1563*******************************************************************************/ 1564BTA_API extern void BTA_DmDiscoverUUID(BD_ADDR bd_addr, tSDP_UUID *uuid, 1565 tBTA_DM_SEARCH_CBACK *p_cback, BOOLEAN sdp_search); 1566 1567/******************************************************************************* 1568** 1569** Function BTA_DmGetCachedRemoteName 1570** 1571** Description Retieve cached remote name if available 1572** 1573** Returns BTA_SUCCESS if cached name was retrieved 1574** BTA_FAILURE if cached name is not available 1575** 1576*******************************************************************************/ 1577tBTA_STATUS BTA_DmGetCachedRemoteName(BD_ADDR remote_device, UINT8 **pp_cached_name); 1578// btla-specific -- 1579 1580/******************************************************************************* 1581** 1582** Function BTA_DmIsMaster 1583** 1584** Description This function checks if the local device is the master of 1585** the link to the given device 1586** 1587** Returns TRUE if master. 1588** FALSE if not. 1589** 1590*******************************************************************************/ 1591BTA_API extern BOOLEAN BTA_DmIsMaster(BD_ADDR bd_addr); 1592 1593/******************************************************************************* 1594** 1595** Function BTA_DmBond 1596** 1597** Description This function initiates a bonding procedure with a peer 1598** device. The bonding procedure enables authentication 1599** and optionally encryption on the Bluetooth link. 1600** 1601** 1602** Returns void 1603** 1604*******************************************************************************/ 1605BTA_API extern void BTA_DmBond(BD_ADDR bd_addr); 1606 1607/******************************************************************************* 1608** 1609** Function BTA_DmBondByTransport 1610** 1611** Description This function initiates a bonding procedure with a peer 1612** device by designated transport. The bonding procedure enables 1613** authentication and optionally encryption on the Bluetooth link. 1614** 1615** 1616** Returns void 1617** 1618*******************************************************************************/ 1619BTA_API extern void BTA_DmBondByTransport(BD_ADDR bd_addr, tBTA_TRANSPORT transport); 1620 1621 1622/******************************************************************************* 1623** 1624** Function BTA_DmBondCancel 1625** 1626** Description This function cancels a bonding procedure with a peer 1627** device. 1628** 1629** 1630** Returns void 1631** 1632*******************************************************************************/ 1633BTA_API extern void BTA_DmBondCancel(BD_ADDR bd_addr); 1634 1635/******************************************************************************* 1636** 1637** Function BTA_DmPinReply 1638** 1639** Description This function provides a PIN when one is requested by DM 1640** during a bonding procedure. The application should call 1641** this function after the security callback is called with 1642** a BTA_DM_PIN_REQ_EVT. 1643** 1644** 1645** Returns void 1646** 1647*******************************************************************************/ 1648BTA_API extern void BTA_DmPinReply(BD_ADDR bd_addr, BOOLEAN accept, UINT8 pin_len, 1649 UINT8 *p_pin); 1650 1651/******************************************************************************* 1652** 1653** Function BTA_DmLinkPolicy 1654** 1655** Description This function sets/clears the link policy mask to the given 1656** bd_addr. 1657** If clearing the sniff or park mode mask, the link is put 1658** in active mode. 1659** 1660** Returns void 1661** 1662*******************************************************************************/ 1663BTA_API extern void BTA_DmLinkPolicy(BD_ADDR bd_addr, tBTA_DM_LP_MASK policy_mask, 1664 BOOLEAN set); 1665 1666#if (BTM_OOB_INCLUDED == TRUE) 1667/******************************************************************************* 1668** 1669** Function BTA_DmLocalOob 1670** 1671** Description This function retrieves the OOB data from local controller. 1672** The result is reported by bta_dm_co_loc_oob(). 1673** 1674** Returns void 1675** 1676*******************************************************************************/ 1677BTA_API extern void BTA_DmLocalOob(void); 1678#endif /* BTM_OOB_INCLUDED */ 1679 1680/******************************************************************************* 1681** 1682** Function BTA_DmConfirm 1683** 1684** Description This function accepts or rejects the numerical value of the 1685** Simple Pairing process on BTA_DM_SP_CFM_REQ_EVT 1686** 1687** Returns void 1688** 1689*******************************************************************************/ 1690BTA_API extern void BTA_DmConfirm(BD_ADDR bd_addr, BOOLEAN accept); 1691 1692/******************************************************************************* 1693** 1694** Function BTA_DmPasskeyCancel 1695** 1696** Description This function is called to cancel the simple pairing process 1697** reported by BTA_DM_SP_KEY_NOTIF_EVT 1698** 1699** Returns void 1700** 1701*******************************************************************************/ 1702BTA_API extern void BTA_DmPasskeyCancel(BD_ADDR bd_addr); 1703 1704/******************************************************************************* 1705** 1706** Function BTA_DmAddDevice 1707** 1708** Description This function adds a device to the security database list 1709** of peer devices. This function would typically be called 1710** at system startup to initialize the security database with 1711** known peer devices. This is a direct execution function 1712** that may lock task scheduling on some platforms. 1713** 1714** Returns void 1715** 1716*******************************************************************************/ 1717BTA_API extern void BTA_DmAddDevice(BD_ADDR bd_addr, DEV_CLASS dev_class, 1718 LINK_KEY link_key, tBTA_SERVICE_MASK trusted_mask, 1719 BOOLEAN is_trusted, UINT8 key_type, 1720 tBTA_IO_CAP io_cap); 1721 1722/******************************************************************************* 1723** 1724** Function BTA_DmAddDevWithName 1725** 1726** Description This function is newer version of BTA_DmAddDevice() 1727** which added bd_name and features as input parameters. 1728** 1729** 1730** Returns void 1731** 1732** Note: features points to the remote device features array. 1733** The array size is 1734** BTA_FEATURE_BYTES_PER_PAGE * (BTA_EXT_FEATURES_PAGE_MAX + 1) 1735** 1736*******************************************************************************/ 1737BTA_API extern void BTA_DmAddDevWithName (BD_ADDR bd_addr, DEV_CLASS dev_class, 1738 BD_NAME bd_name, UINT8 *features, 1739 LINK_KEY link_key, tBTA_SERVICE_MASK trusted_mask, 1740 BOOLEAN is_trusted, UINT8 key_type, tBTA_IO_CAP io_cap); 1741 1742/******************************************************************************* 1743** 1744** Function BTA_DmRemoveDevice 1745** 1746** Description This function removes a device from the security database. 1747** This is a direct execution function that may lock task 1748** scheduling on some platforms. 1749** 1750** 1751** Returns BTA_SUCCESS if successful. 1752** BTA_FAIL if operation failed. 1753** 1754*******************************************************************************/ 1755BTA_API extern tBTA_STATUS BTA_DmRemoveDevice(BD_ADDR bd_addr); 1756 1757/******************************************************************************* 1758** 1759** Function BTA_DmAuthorizeReply 1760** 1761** Description This function provides an authorization reply when 1762** authorization is requested by BTA. The application calls 1763** this function after the security callback is called with 1764** a BTA_DM_AUTHORIZE_EVT. 1765** 1766** 1767** Returns void 1768** 1769*******************************************************************************/ 1770BTA_API extern void BTA_DmAuthorizeReply(BD_ADDR bd_addr, tBTA_SERVICE_ID service, 1771 tBTA_AUTH_RESP response); 1772 1773/******************************************************************************* 1774** 1775** Function BTA_DmSignalStrength 1776** 1777** Description This function initiates RSSI and channnel quality 1778** measurments. BTA_DM_SIG_STRENGTH_EVT is sent to 1779** application with the values of RSSI and channel 1780** quality 1781** 1782** 1783** Returns void 1784** 1785*******************************************************************************/ 1786BTA_API extern void BTA_DmSignalStrength(tBTA_SIG_STRENGTH_MASK mask, UINT16 period, BOOLEAN start); 1787 1788/******************************************************************************* 1789** 1790** Function BTA_DmWriteInqTxPower 1791** 1792** Description This command is used to write the inquiry transmit power level 1793** used to transmit the inquiry (ID) data packets. 1794** 1795** Parameters tx_power - tx inquiry power to use, valid value is -70 ~ 20 1796 1797** Returns void 1798** 1799*******************************************************************************/ 1800BTA_API extern void BTA_DmWriteInqTxPower(INT8 tx_power); 1801 1802/******************************************************************************* 1803** 1804** Function BTA_DmEirAddUUID 1805** 1806** Description This function is called to add UUID into EIR. 1807** 1808** Parameters tBT_UUID - UUID 1809** 1810** Returns None 1811** 1812*******************************************************************************/ 1813BTA_API extern void BTA_DmEirAddUUID (tBT_UUID *p_uuid); 1814 1815/******************************************************************************* 1816** 1817** Function BTA_DmEirRemoveUUID 1818** 1819** Description This function is called to remove UUID from EIR. 1820** 1821** Parameters tBT_UUID - UUID 1822** 1823** Returns None 1824** 1825*******************************************************************************/ 1826BTA_API extern void BTA_DmEirRemoveUUID (tBT_UUID *p_uuid); 1827 1828/******************************************************************************* 1829** 1830** Function BTA_DmSetEIRConfig 1831** 1832** Description This function is called to override the BTA default EIR parameters. 1833** This funciton is only valid in a system where BTU & App task 1834** are in the same memory space. 1835** 1836** Parameters Pointer to User defined EIR config 1837** 1838** Returns None 1839** 1840*******************************************************************************/ 1841BTA_API extern void BTA_DmSetEIRConfig (tBTA_DM_EIR_CONF *p_eir_cfg); 1842 1843/******************************************************************************* 1844** 1845** Function BTA_CheckEirData 1846** 1847** Description This function is called to get EIR data from significant part. 1848** 1849** Parameters p_eir - pointer of EIR significant part 1850** type - finding EIR data type 1851** p_length - return the length of EIR data 1852** 1853** Returns pointer of EIR data 1854** 1855*******************************************************************************/ 1856BTA_API extern UINT8 *BTA_CheckEirData( UINT8 *p_eir, UINT8 tag, UINT8 *p_length ); 1857 1858/******************************************************************************* 1859** 1860** Function BTA_GetEirService 1861** 1862** Description This function is called to get BTA service mask from EIR. 1863** 1864** Parameters p_eir - pointer of EIR significant part 1865** p_services - return the BTA service mask 1866** 1867** Returns None 1868** 1869*******************************************************************************/ 1870BTA_API extern void BTA_GetEirService( UINT8 *p_eir, tBTA_SERVICE_MASK *p_services ); 1871 1872/******************************************************************************* 1873** 1874** Function BTA_DmUseSsr 1875** 1876** Description This function is called to check if the connected peer device 1877** supports SSR or not. 1878** 1879** Returns TRUE, if SSR is supported 1880** 1881*******************************************************************************/ 1882BTA_API extern BOOLEAN BTA_DmUseSsr( BD_ADDR bd_addr ); 1883 1884/******************************************************************************* 1885** 1886** Function BTA_DmGetConnectionState 1887** 1888** Description Returns whether the remote device is currently connected. 1889** 1890** Returns 0 if the device is NOT connected. 1891** 1892*******************************************************************************/ 1893BTA_API extern UINT16 BTA_DmGetConnectionState( BD_ADDR bd_addr ); 1894 1895 1896/******************************************************************************* 1897** 1898** Function BTA_DmSetLocalDiRecord 1899** 1900** Description This function adds a DI record to the local SDP database. 1901** 1902** Returns BTA_SUCCESS if record set sucessfully, otherwise error code. 1903** 1904*******************************************************************************/ 1905BTA_API extern tBTA_STATUS BTA_DmSetLocalDiRecord( tBTA_DI_RECORD *p_device_info, 1906 UINT32 *p_handle ); 1907 1908/******************************************************************************* 1909** 1910** Function BTA_DmGetLocalDiRecord 1911** 1912** Description Get a specified DI record to the local SDP database. If no 1913** record handle is provided, the primary DI record will be 1914** returned. 1915** 1916** Returns BTA_SUCCESS if record set sucessfully, otherwise error code. 1917** 1918*******************************************************************************/ 1919BTA_API extern tBTA_STATUS BTA_DmGetLocalDiRecord( tBTA_DI_GET_RECORD *p_device_info, 1920 UINT32 *p_handle ); 1921 1922/******************************************************************************* 1923** 1924** Function BTA_DmDiDiscover 1925** 1926** Description This function queries a remote device for DI information. 1927** 1928** Returns None. 1929** 1930*******************************************************************************/ 1931BTA_API extern void BTA_DmDiDiscover( BD_ADDR remote_device, tBTA_DISCOVERY_DB *p_db, 1932 UINT32 len, tBTA_DM_SEARCH_CBACK *p_cback ); 1933 1934/******************************************************************************* 1935** 1936** Function BTA_DmGetDiRecord 1937** 1938** Description This function retrieves a remote device's DI record from 1939** the specified database. 1940** 1941** Returns None. 1942** 1943*******************************************************************************/ 1944BTA_API extern tBTA_STATUS BTA_DmGetDiRecord( UINT8 get_record_index, tBTA_DI_GET_RECORD *p_device_info, 1945 tBTA_DISCOVERY_DB *p_db ); 1946 1947/******************************************************************************* 1948** 1949** 1950** Function BTA_DmCloseACL 1951** 1952** Description This function force to close an ACL connection and remove the 1953** device from the security database list of known devices. 1954** 1955** Parameters: bd_addr - Address of the peer device 1956** remove_dev - remove device or not after link down 1957** transport - which transport to close 1958 1959** 1960** Returns void. 1961** 1962*******************************************************************************/ 1963BTA_API extern void BTA_DmCloseACL(BD_ADDR bd_addr, BOOLEAN remove_dev, tBTA_TRANSPORT transport); 1964 1965/******************************************************************************* 1966** 1967** Function BTA_SysFeatures 1968** 1969** Description This function is called to set system features. 1970** 1971** Returns void 1972** 1973*******************************************************************************/ 1974BTA_API extern void BTA_SysFeatures (UINT16 sys_features); 1975 1976/******************************************************************************* 1977** 1978** Function bta_dmexecutecallback 1979** 1980** Description This function will request BTA to execute a call back in the context of BTU task 1981** This API was named in lower case because it is only intended 1982** for the internal customers(like BTIF). 1983** 1984** Returns void 1985** 1986*******************************************************************************/ 1987BTA_API extern void bta_dmexecutecallback (tBTA_DM_EXEC_CBACK* p_callback, void * p_param); 1988 1989#if (BTM_SCO_HCI_INCLUDED == TRUE) 1990/******************************************************************************* 1991** 1992** Function BTA_DmPcmInitSamples 1993** 1994** Description initialize the down sample converter. 1995** 1996** src_sps: original samples per second (source audio data) 1997** (ex. 44100, 48000) 1998** bits: number of bits per pcm sample (16) 1999** n_channels: number of channels (i.e. mono(1), stereo(2)...) 2000** 2001** Returns none 2002** 2003*******************************************************************************/ 2004BTA_API extern void BTA_DmPcmInitSamples (UINT32 src_sps, UINT32 bits, UINT32 n_channels); 2005 2006/************************************************************************************** 2007** Function BTA_DmPcmResample 2008** 2009** Description Down sampling utility to convert higher sampling rate into 8K/16bits 2010** PCM samples. 2011** 2012** Parameters p_src: pointer to the buffer where the original sampling PCM 2013** are stored. 2014** in_bytes: Length of the input PCM sample buffer in byte. 2015** p_dst: pointer to the buffer which is to be used to store 2016** the converted PCM samples. 2017** 2018** 2019** Returns INT32: number of samples converted. 2020** 2021**************************************************************************************/ 2022BTA_API extern INT32 BTA_DmPcmResample (void *p_src, UINT32 in_bytes, void *p_dst); 2023#endif 2024 2025#if ((defined BLE_INCLUDED) && (BLE_INCLUDED == TRUE)) 2026/* BLE related API functions */ 2027/******************************************************************************* 2028** 2029** Function BTA_DmBleSecurityGrant 2030** 2031** Description Grant security request access. 2032** 2033** Parameters: bd_addr - BD address of the peer 2034** res - security grant status. 2035** 2036** Returns void 2037** 2038*******************************************************************************/ 2039BTA_API extern void BTA_DmBleSecurityGrant(BD_ADDR bd_addr, tBTA_DM_BLE_SEC_GRANT res); 2040 2041 2042 2043/******************************************************************************* 2044** 2045** Function BTA_DmBleSetBgConnType 2046** 2047** Description This function is called to set BLE connectable mode for a 2048** peripheral device. 2049** 2050** Parameters bg_conn_type: it can be auto connection, or selective connection. 2051** p_select_cback: callback function when selective connection procedure 2052** is being used. 2053** 2054** Returns void 2055** 2056*******************************************************************************/ 2057BTA_API extern void BTA_DmBleSetBgConnType(tBTA_DM_BLE_CONN_TYPE bg_conn_type, tBTA_DM_BLE_SEL_CBACK *p_select_cback); 2058 2059/******************************************************************************* 2060** 2061** Function BTA_DmBlePasskeyReply 2062** 2063** Description Send BLE SMP passkey reply. 2064** 2065** Parameters: bd_addr - BD address of the peer 2066** accept - passkey entry sucessful or declined. 2067** passkey - passkey value, must be a 6 digit number, 2068** can be lead by 0. 2069** 2070** Returns void 2071** 2072*******************************************************************************/ 2073BTA_API extern void BTA_DmBlePasskeyReply(BD_ADDR bd_addr, BOOLEAN accept, UINT32 passkey); 2074 2075/******************************************************************************* 2076** 2077** Function BTA_DmAddBleDevice 2078** 2079** Description Add a BLE device. This function will be normally called 2080** during host startup to restore all required information 2081** for a LE device stored in the NVRAM. 2082** 2083** Parameters: bd_addr - BD address of the peer 2084** dev_type - Remote device's device type. 2085** addr_type - LE device address type. 2086** 2087** Returns void 2088** 2089*******************************************************************************/ 2090BTA_API extern void BTA_DmAddBleDevice(BD_ADDR bd_addr, tBLE_ADDR_TYPE addr_type, 2091 tBT_DEVICE_TYPE dev_type); 2092 2093 2094/******************************************************************************* 2095** 2096** Function BTA_DmAddBleKey 2097** 2098** Description Add/modify LE device information. This function will be 2099** normally called during host startup to restore all required 2100** information stored in the NVRAM. 2101** 2102** Parameters: bd_addr - BD address of the peer 2103** p_le_key - LE key values. 2104** key_type - LE SMP key type. 2105** 2106** Returns void 2107** 2108*******************************************************************************/ 2109BTA_API extern void BTA_DmAddBleKey (BD_ADDR bd_addr, 2110 tBTA_LE_KEY_VALUE *p_le_key, 2111 tBTA_LE_KEY_TYPE key_type); 2112 2113/******************************************************************************* 2114** 2115** Function BTA_DmSetBlePrefConnParams 2116** 2117** Description This function is called to set the preferred connection 2118** parameters when default connection parameter is not desired. 2119** 2120** Parameters: bd_addr - BD address of the peripheral 2121** min_conn_int - minimum preferred connection interval 2122** max_conn_int - maximum preferred connection interval 2123** slave_latency - preferred slave latency 2124** supervision_tout - preferred supervision timeout 2125** 2126** 2127** Returns void 2128** 2129*******************************************************************************/ 2130BTA_API extern void BTA_DmSetBlePrefConnParams(BD_ADDR bd_addr, 2131 UINT16 min_conn_int, UINT16 max_conn_int, 2132 UINT16 slave_latency, UINT16 supervision_tout ); 2133 2134/******************************************************************************* 2135** 2136** Function BTA_DmSetBleConnScanParams 2137** 2138** Description This function is called to set scan parameters used in 2139** BLE connection request 2140** 2141** Parameters: bd_addr - BD address of the peripheral 2142** scan_interval - scan interval 2143** scan_window - scan window 2144** 2145** Returns void 2146** 2147*******************************************************************************/ 2148BTA_API extern void BTA_DmSetBleConnScanParams(UINT16 scan_interval, 2149 UINT16 scan_window ); 2150 2151/******************************************************************************* 2152** 2153** Function BTA_DmSetBleAdvParams 2154** 2155** Description This function sets the advertising parameters BLE functionality. 2156** It is to be called when device act in peripheral or broadcaster 2157** role. 2158** 2159** Parameters: adv_int_min - adv interval minimum 2160** adv_int_max - adv interval max 2161** p_dir_bda - directed adv initator address 2162** 2163** Returns void 2164** 2165*******************************************************************************/ 2166BTA_API extern void BTA_DmSetBleAdvParams (UINT16 adv_int_min, UINT16 adv_int_max, 2167 tBLE_BD_ADDR *p_dir_bda); 2168/******************************************************************************* 2169** 2170** Function BTA_DmSearchExt 2171** 2172** Description This function searches for peer Bluetooth devices. It performs 2173** an inquiry and gets the remote name for devices. Service 2174** discovery is done if services is non zero 2175** 2176** Parameters p_dm_inq: inquiry conditions 2177** services: if service is not empty, service discovery will be done. 2178** for all GATT based service condition, put num_uuid, and 2179** p_uuid is the pointer to the list of UUID values. 2180** p_cback: callback functino when search is completed. 2181** 2182** 2183** 2184** Returns void 2185** 2186*******************************************************************************/ 2187BTA_API extern void BTA_DmSearchExt(tBTA_DM_INQ *p_dm_inq, tBTA_SERVICE_MASK_EXT *p_services, 2188 tBTA_DM_SEARCH_CBACK *p_cback); 2189 2190/******************************************************************************* 2191** 2192** Function BTA_DmDiscoverExt 2193** 2194** Description This function does service discovery for services of a 2195** peer device. When services.num_uuid is 0, it indicates all 2196** GATT based services are to be searched; other wise a list of 2197** UUID of interested services should be provided through 2198** services.p_uuid. 2199** 2200** 2201** 2202** Returns void 2203** 2204*******************************************************************************/ 2205BTA_API extern void BTA_DmDiscoverExt(BD_ADDR bd_addr, tBTA_SERVICE_MASK_EXT *p_services, 2206 tBTA_DM_SEARCH_CBACK *p_cback, BOOLEAN sdp_search); 2207 2208/******************************************************************************* 2209** 2210** Function BTA_DmDiscoverByTransport 2211** 2212** Description This function does service discovery on particular transport 2213** for services of a 2214** peer device. When services.num_uuid is 0, it indicates all 2215** GATT based services are to be searched; other wise a list of 2216** UUID of interested services should be provided through 2217** p_services->p_uuid. 2218** 2219** 2220** 2221** Returns void 2222** 2223*******************************************************************************/ 2224BTA_API extern void BTA_DmDiscoverByTransport(BD_ADDR bd_addr, tBTA_SERVICE_MASK_EXT *p_services, 2225 tBTA_DM_SEARCH_CBACK *p_cback, BOOLEAN sdp_search, 2226 tBTA_TRANSPORT transport); 2227 2228/******************************************************************************* 2229** 2230** Function BTA_DmSetEncryption 2231** 2232** Description This function is called to ensure that connection is 2233** encrypted. Should be called only on an open connection. 2234** Typically only needed for connections that first want to 2235** bring up unencrypted links, then later encrypt them. 2236** 2237** Parameters: bd_addr - Address of the peer device 2238** transport - transport of the link to be encruypted 2239** p_callback - Pointer to callback function to indicat the 2240** link encryption status 2241** sec_act - This is the security action to indicate 2242** what knid of BLE security level is required for 2243** the BLE link if the BLE is supported 2244** Note: This parameter is ignored for the BR/EDR link 2245** or the BLE is not supported 2246** 2247** Returns void 2248** 2249** 2250*******************************************************************************/ 2251BTA_API extern void BTA_DmSetEncryption(BD_ADDR bd_addr, tBTA_TRANSPORT transport, 2252 tBTA_DM_ENCRYPT_CBACK *p_callback, 2253 tBTA_DM_BLE_SEC_ACT sec_act); 2254 2255 2256/******************************************************************************* 2257** 2258** Function BTA_DmBleObserve 2259** 2260** Description This procedure keep the device listening for advertising 2261** events from a broadcast device. 2262** 2263** Parameters start: start or stop observe. 2264** duration : Duration of the scan. Continuous scan if 0 is passed 2265** p_results_cb: Callback to be called with scan results 2266** 2267** Returns void 2268** 2269*******************************************************************************/ 2270BTA_API extern void BTA_DmBleObserve(BOOLEAN start, UINT8 duration, 2271 tBTA_DM_SEARCH_CBACK *p_results_cb); 2272 2273 2274#endif 2275 2276// btla-specific ++ 2277/******************************************************************************* 2278** 2279** Function BTA_DmSetAfhChannelAssessment 2280** 2281** Description This function is called to set the channel assessment mode on or off 2282** 2283** Returns status 2284** 2285*******************************************************************************/ 2286BTA_API extern void BTA_DmSetAfhChannelAssessment (BOOLEAN enable_or_disable); 2287 2288#if BLE_INCLUDED == TRUE 2289// btla-specific -- 2290/******************************************************************************* 2291** 2292** Function BTA_DmBleConfigLocalPrivacy 2293** 2294** Description Enable/disable privacy on the local device 2295** 2296** Parameters: privacy_enable - enable/disabe privacy on remote device. 2297** 2298** Returns void 2299** 2300*******************************************************************************/ 2301BTA_API extern void BTA_DmBleConfigLocalPrivacy(BOOLEAN privacy_enable); 2302 2303/******************************************************************************* 2304** 2305** Function BTA_DmBleEnableRemotePrivacy 2306** 2307** Description Enable/disable privacy on a remote device 2308** 2309** Parameters: bd_addr - BD address of the peer 2310** privacy_enable - enable/disabe privacy on remote device. 2311** 2312** Returns void 2313** 2314*******************************************************************************/ 2315BTA_API extern void BTA_DmBleEnableRemotePrivacy(BD_ADDR bd_addr, BOOLEAN privacy_enable); 2316 2317 2318/******************************************************************************* 2319** 2320** Function BTA_DmBleSetAdvConfig 2321** 2322** Description This function is called to override the BTA default ADV parameters. 2323** 2324** Parameters Pointer to User defined ADV data structure 2325** 2326** Returns None 2327** 2328*******************************************************************************/ 2329BTA_API extern void BTA_DmBleSetAdvConfig (tBTA_BLE_AD_MASK data_mask, 2330 tBTA_BLE_ADV_DATA *p_adv_cfg, 2331 tBTA_SET_ADV_DATA_CMPL_CBACK *p_adv_data_cback); 2332 2333/******************************************************************************* 2334** 2335** Function BTA_DmBleSetScanRsp 2336** 2337** Description This function is called to override the BTA scan response. 2338** 2339** Parameters Pointer to User defined ADV data structure 2340** 2341** Returns None 2342** 2343*******************************************************************************/ 2344BTA_API extern void BTA_DmBleSetScanRsp (tBTA_BLE_AD_MASK data_mask, 2345 tBTA_BLE_ADV_DATA *p_adv_cfg, 2346 tBTA_SET_ADV_DATA_CMPL_CBACK *p_adv_data_cback); 2347 2348/******************************************************************************* 2349** 2350** Function BTA_DmBleBroadcast 2351** 2352** Description This function starts or stops LE broadcasting. 2353** 2354** Parameters start: start or stop broadcast. 2355** 2356** Returns None 2357** 2358*******************************************************************************/ 2359BTA_API extern void BTA_DmBleBroadcast (BOOLEAN start); 2360 2361 2362/******************************************************************************* 2363** 2364** Function BTA_BleEnableAdvInstance 2365** 2366** Description This function enables the Multi ADV instance feature 2367** 2368** Parameters p_params Pointer to ADV param user defined structure 2369** p_cback Pointer to Multi ADV callback structure 2370** p_ref - Reference pointer 2371** 2372** Returns None 2373** 2374*******************************************************************************/ 2375BTA_API extern void BTA_BleEnableAdvInstance (tBTA_BLE_ADV_PARAMS *p_params, 2376 tBTA_BLE_MULTI_ADV_CBACK *p_cback,void *p_ref); 2377 2378/******************************************************************************* 2379** 2380** Function BTA_BleUpdateAdvInstParam 2381** 2382** Description This function updates the Multi ADV instance params 2383** 2384** Parameters inst_id Instance ID 2385** p_params Pointer to ADV param user defined structure 2386** 2387** Returns None 2388** 2389*******************************************************************************/ 2390BTA_API extern void BTA_BleUpdateAdvInstParam (UINT8 inst_id, 2391 tBTA_BLE_ADV_PARAMS *p_params); 2392 2393/******************************************************************************* 2394** 2395** Function BTA_BleCfgAdvInstData 2396** 2397** Description This function is called to configure the ADV instance data 2398** 2399** Parameters inst_id - Instance ID 2400** is_scan_rsp - Boolean value Scan response 2401** Pointer to User defined ADV data structure 2402** Returns None 2403** 2404*******************************************************************************/ 2405BTA_API extern void BTA_BleCfgAdvInstData (UINT8 inst_id, BOOLEAN is_scan_rsp, 2406 tBTA_BLE_AD_MASK data_mask, tBTA_BLE_ADV_DATA *p_data); 2407 2408/******************************************************************************* 2409** 2410** Function BTA_BleDisableAdvInstance 2411** 2412** Description This function is called to disable the ADV instance 2413** 2414** Parameters inst_id - Instance ID to be disabled 2415** 2416** Returns None 2417** 2418*******************************************************************************/ 2419BTA_API extern void BTA_BleDisableAdvInstance(UINT8 inst_id); 2420 2421/******************************************************************************* 2422** 2423** Function BTA_DmBleUpdateConnectionParams 2424** 2425** Description Update connection parameters, can only be used when connection is up. 2426** 2427** Parameters: bd_addr - BD address of the peer 2428** min_int - minimum connection interval, [0x0004~ 0x4000] 2429** max_int - maximum connection interval, [0x0004~ 0x4000] 2430** latency - slave latency [0 ~ 500] 2431** timeout - supervision timeout [0x000a ~ 0xc80] 2432** 2433** Returns void 2434** 2435*******************************************************************************/ 2436BTA_API extern void BTA_DmBleUpdateConnectionParams(BD_ADDR bd_addr, UINT16 min_int, 2437 UINT16 max_int, UINT16 latency, UINT16 timeout); 2438 2439/******************************************************************************* 2440** 2441** Function BTA_DmBleSetStorageParams 2442** 2443** Description This function is called to set the storage parameters 2444** 2445** Parameters batch_scan_full_max -Max storage space (in %) allocated to full scanning 2446** batch_scan_trunc_max -Max storage space (in %) allocated to truncated scanning 2447** batch_scan_notify_threshold - Setup notification level based on total space 2448** consumed by both pools. Setting it to 0 will disable threshold notification 2449** p_setup_cback - Setup callback 2450** p_thres_cback - Threshold callback 2451** p_rep_cback - Reports callback 2452** ref_value - Reference value 2453** 2454** Returns None 2455** 2456*******************************************************************************/ 2457BTA_API extern void BTA_DmBleSetStorageParams(UINT8 batch_scan_full_max, 2458 UINT8 batch_scan_trunc_max, 2459 UINT8 batch_scan_notify_threshold, 2460 tBTA_BLE_SCAN_SETUP_CBACK *p_setup_cback, 2461 tBTA_BLE_SCAN_THRESHOLD_CBACK *p_thres_cback, 2462 tBTA_BLE_SCAN_REP_CBACK* p_rep_cback, 2463 tBTA_DM_BLE_REF_VALUE ref_value); 2464 2465/******************************************************************************* 2466** 2467** Function BTA_DmBleEnableBatchScan 2468** 2469** Description This function is called to enable the batch scan 2470** 2471** Parameters scan_mode -Batch scan mode 2472** scan_interval - Scan interval 2473** scan_window - Scan window 2474** discard_rule -Discard rules 2475** addr_type - Address type 2476** ref_value - Reference value 2477** 2478** Returns None 2479** 2480*******************************************************************************/ 2481BTA_API extern void BTA_DmBleEnableBatchScan(tBTA_BLE_SCAN_MODE scan_mode, 2482 UINT32 scan_interval, UINT32 scan_window, 2483 tBTA_BLE_DISCARD_RULE discard_rule, 2484 tBLE_ADDR_TYPE addr_type, 2485 tBTA_DM_BLE_REF_VALUE ref_value); 2486 2487/******************************************************************************* 2488** 2489** Function BTA_DmBleReadScanReports 2490** 2491** Description This function is called to read the batch scan reports 2492** 2493** Parameters scan_mode -Batch scan mode 2494** ref_value - Reference value 2495** 2496** Returns None 2497** 2498*******************************************************************************/ 2499BTA_API extern void BTA_DmBleReadScanReports(tBTA_BLE_SCAN_MODE scan_type, 2500 tBTA_DM_BLE_REF_VALUE ref_value); 2501 2502/******************************************************************************* 2503** 2504** Function BTA_DmBleDisableBatchScan 2505** 2506** Description This function is called to disable the batch scanning 2507** 2508** Parameters ref_value - Reference value 2509** 2510** Returns None 2511** 2512*******************************************************************************/ 2513BTA_API extern void BTA_DmBleDisableBatchScan(tBTA_DM_BLE_REF_VALUE ref_value); 2514 2515/******************************************************************************* 2516** 2517** Function BTA_DmEnableScanFilter 2518** 2519** Description This function is called to enable the adv data payload filter 2520** 2521** Parameters action - enable or disable the APCF feature 2522** p_cmpl_cback - Command completed callback 2523** ref_value - Reference value 2524** 2525** Returns void 2526** 2527*******************************************************************************/ 2528BTA_API extern void BTA_DmEnableScanFilter(UINT8 action, 2529 tBTA_DM_BLE_PF_STATUS_CBACK *p_cmpl_cback, 2530 tBTA_DM_BLE_REF_VALUE ref_value); 2531 2532/******************************************************************************* 2533** 2534** Function BTA_DmBleScanFilterSetup 2535** 2536** Description This function is called to setup the filter params 2537** 2538** Parameters p_target: enable the filter condition on a target device; if NULL 2539** filt_index - Filter index 2540** p_filt_params -Filter parameters 2541** ref_value - Reference value 2542** action - Add, delete or clear 2543** p_cmpl_back - Command completed callback 2544** 2545** Returns void 2546** 2547*******************************************************************************/ 2548BTA_API extern void BTA_DmBleScanFilterSetup(UINT8 action, 2549 tBTA_DM_BLE_PF_FILT_INDEX filt_index, 2550 tBTA_DM_BLE_PF_FILT_PARAMS *p_filt_params, 2551 tBLE_BD_ADDR *p_target, 2552 tBTA_DM_BLE_PF_PARAM_CBACK *p_cmpl_cback, 2553 tBTA_DM_BLE_REF_VALUE ref_value); 2554 2555/******************************************************************************* 2556** 2557** Function BTA_DmBleCfgFilterCondition 2558** 2559** Description This function is called to configure the adv data payload filter 2560** condition. 2561** 2562** Parameters action: to read/write/clear 2563** cond_type: filter condition type 2564** filt_index - Filter index 2565** p_cond: filter condition parameter 2566** p_cmpl_back - Command completed callback 2567** ref_value - Reference value 2568** 2569** Returns void 2570** 2571*******************************************************************************/ 2572BTA_API extern void BTA_DmBleCfgFilterCondition(tBTA_DM_BLE_SCAN_COND_OP action, 2573 tBTA_DM_BLE_PF_COND_TYPE cond_type, 2574 tBTA_DM_BLE_PF_FILT_INDEX filt_index, 2575 tBTA_DM_BLE_PF_COND_PARAM *p_cond, 2576 tBTA_DM_BLE_PF_CFG_CBACK *p_cmpl_cback, 2577 tBTA_DM_BLE_REF_VALUE ref_value); 2578 2579 2580/******************************************************************************* 2581** 2582** Function BTA_DmBleTrackAdvertiser 2583** 2584** Description This function is called to track the advertiser 2585** 2586** Parameters ref_value - Reference value 2587** p_track_adv_cback - ADV callback 2588** 2589** Returns None 2590** 2591*******************************************************************************/ 2592BTA_API extern void BTA_DmBleTrackAdvertiser(tBTA_DM_BLE_REF_VALUE ref_value, 2593 tBTA_BLE_TRACK_ADV_CBACK *p_track_adv_cback); 2594 2595/******************************************************************************* 2596** 2597** Function BTA_DmBleGetEnergyInfo 2598** 2599** Description This function is called to obtain the energy info 2600** 2601** Parameters p_cmpl_cback - Command complete callback 2602** 2603** Returns void 2604** 2605*******************************************************************************/ 2606BTA_API extern void BTA_DmBleGetEnergyInfo(tBTA_BLE_ENERGY_INFO_CBACK *p_cmpl_cback); 2607 2608/******************************************************************************* 2609** 2610** Function BTA_BrcmInit 2611** 2612** Description This function initializes Broadcom specific VS handler in BTA 2613** 2614** Returns void 2615** 2616*******************************************************************************/ 2617BTA_API extern void BTA_VendorInit (void); 2618 2619/******************************************************************************* 2620** 2621** Function BTA_BrcmCleanup 2622** 2623** Description This function frees up Broadcom specific VS specific dynamic memory 2624** 2625** Returns void 2626** 2627*******************************************************************************/ 2628BTA_API extern void BTA_VendorCleanup (void); 2629 2630#endif 2631 2632#ifdef __cplusplus 2633} 2634#endif 2635 2636#endif /* BTA_API_H */ 2637 2638