1#include "wifi_hal.h"
2
3#ifndef __WIFI_HAL_STATS_H
4#define __WIFI_HAL_STATS_H
5
6#ifdef __cplusplus
7extern "C"
8{
9#endif /* __cplusplus */
10
11#define STATS_MAJOR_VERSION      1
12#define STATS_MINOR_VERSION      0
13#define STATS_MICRO_VERSION      0
14
15typedef enum {
16    WIFI_DISCONNECTED = 0,
17    WIFI_AUTHENTICATING = 1,
18    WIFI_ASSOCIATING = 2,
19    WIFI_ASSOCIATED = 3,
20    WIFI_EAPOL_STARTED = 4,   // if done by firmware/driver
21    WIFI_EAPOL_COMPLETED = 5, // if done by firmware/driver
22} wifi_connection_state;
23
24typedef enum {
25    WIFI_ROAMING_IDLE = 0,
26    WIFI_ROAMING_ACTIVE = 1,
27} wifi_roam_state;
28
29typedef enum {
30    WIFI_INTERFACE_STA = 0,
31    WIFI_INTERFACE_SOFTAP = 1,
32    WIFI_INTERFACE_IBSS = 2,
33    WIFI_INTERFACE_P2P_CLIENT = 3,
34    WIFI_INTERFACE_P2P_GO = 4,
35    WIFI_INTERFACE_NAN = 5,
36    WIFI_INTERFACE_MESH = 6,
37    WIFI_INTERFACE_UNKNOWN = -1
38 } wifi_interface_mode;
39
40#define WIFI_CAPABILITY_QOS          0x00000001     // set for QOS association
41#define WIFI_CAPABILITY_PROTECTED    0x00000002     // set for protected association (802.11 beacon frame control protected bit set)
42#define WIFI_CAPABILITY_INTERWORKING 0x00000004     // set if 802.11 Extended Capabilities element interworking bit is set
43#define WIFI_CAPABILITY_HS20         0x00000008     // set for HS20 association
44#define WIFI_CAPABILITY_SSID_UTF8    0x00000010     // set is 802.11 Extended Capabilities element UTF-8 SSID bit is set
45#define WIFI_CAPABILITY_COUNTRY      0x00000020     // set is 802.11 Country Element is present
46
47typedef struct {
48   wifi_interface_mode mode;     // interface mode
49   u8 mac_addr[6];               // interface mac address (self)
50   wifi_connection_state state;  // connection state (valid for STA, CLI only)
51   wifi_roam_state roaming;      // roaming state
52   u32 capabilities;             // WIFI_CAPABILITY_XXX (self)
53   u8 ssid[33];                  // null terminated SSID
54   u8 bssid[6];                  // bssid
55   u8 ap_country_str[3];         // country string advertised by AP
56   u8 country_str[3];            // country string for this association
57} wifi_interface_link_layer_info;
58
59/* channel information */
60typedef struct {
61   wifi_channel_width width;   // channel width (20, 40, 80, 80+80, 160)
62   wifi_channel center_freq;   // primary 20 MHz channel
63   wifi_channel center_freq0;  // center frequency (MHz) first segment
64   wifi_channel center_freq1;  // center frequency (MHz) second segment
65} wifi_channel_info;
66
67/* wifi rate */
68typedef struct {
69   u32 preamble   :3;   // 0: OFDM, 1:CCK, 2:HT 3:VHT 4..7 reserved
70   u32 nss        :2;   // 0:1x1, 1:2x2, 3:3x3, 4:4x4
71   u32 bw         :3;   // 0:20MHz, 1:40Mhz, 2:80Mhz, 3:160Mhz
72   u32 rateMcsIdx :8;   // OFDM/CCK rate code would be as per ieee std in the units of 0.5mbps
73                        // HT/VHT it would be mcs index
74   u32 reserved  :16;   // reserved
75   u32 bitrate;         // units of 100 Kbps
76} wifi_rate;
77
78/* channel statistics */
79typedef struct {
80   wifi_channel_info channel;  // channel
81   u32 on_time;                // msecs the radio is awake (32 bits number accruing over time)
82   u32 cca_busy_time;          // msecs the CCA register is busy (32 bits number accruing over time)
83} wifi_channel_stat;
84
85// Max number of tx power levels. The actual number vary per device and is specified by |num_tx_levels|
86#define RADIO_STAT_MAX_TX_LEVELS 256
87
88/* radio statistics */
89typedef struct {
90   wifi_radio radio;                      // wifi radio (if multiple radio supported)
91   u32 on_time;                           // msecs the radio is awake (32 bits number accruing over time)
92   u32 tx_time;                           // msecs the radio is transmitting (32 bits number accruing over time)
93   u32 num_tx_levels;                     // number of radio transmit power levels
94   u32 *tx_time_per_levels;               // pointer to an array of radio transmit per power levels in
95                                          // msecs accured over time
96   u32 rx_time;                           // msecs the radio is in active receive (32 bits number accruing over time)
97   u32 on_time_scan;                      // msecs the radio is awake due to all scan (32 bits number accruing over time)
98   u32 on_time_nbd;                       // msecs the radio is awake due to NAN (32 bits number accruing over time)
99   u32 on_time_gscan;                     // msecs the radio is awake due to G?scan (32 bits number accruing over time)
100   u32 on_time_roam_scan;                 // msecs the radio is awake due to roam?scan (32 bits number accruing over time)
101   u32 on_time_pno_scan;                  // msecs the radio is awake due to PNO scan (32 bits number accruing over time)
102   u32 on_time_hs20;                      // msecs the radio is awake due to HS2.0 scans and GAS exchange (32 bits number accruing over time)
103   u32 num_channels;                      // number of channels
104   wifi_channel_stat channels[];          // channel statistics
105} wifi_radio_stat;
106
107/**
108 * Packet statistics reporting by firmware is performed on MPDU basi (i.e. counters increase by 1 for each MPDU)
109 * As well, "data packet" in associated comments, shall be interpreted as 802.11 data packet,
110 * that is, 802.11 frame control subtype == 2 and excluding management and control frames.
111 *
112 * As an example, in the case of transmission of an MSDU fragmented in 16 MPDUs which are transmitted
113 * OTA in a 16 units long a-mpdu, for which a block ack is received with 5 bits set:
114 *          tx_mpdu : shall increase by 5
115 *          retries : shall increase by 16
116 *          tx_ampdu : shall increase by 1
117 * data packet counters shall not increase regardless of the number of BAR potentially sent by device for this a-mpdu
118 * data packet counters shall not increase regardless of the number of BA received by device for this a-mpdu
119 *
120 * For each subsequent retransmission of the 11 remaining non ACK'ed mpdus
121 * (regardless of the fact that they are transmitted in a-mpdu or not)
122 *          retries : shall increase by 1
123 *
124 * If no subsequent BA or ACK are received from AP, until packet lifetime expires for those 11 packet that were not ACK'ed
125 *          mpdu_lost : shall increase by 11
126 */
127
128/* per rate statistics */
129typedef struct {
130   wifi_rate rate;     // rate information
131   u32 tx_mpdu;        // number of successfully transmitted data pkts (ACK rcvd)
132   u32 rx_mpdu;        // number of received data pkts
133   u32 mpdu_lost;      // number of data packet losses (no ACK)
134   u32 retries;        // total number of data pkt retries
135   u32 retries_short;  // number of short data pkt retries
136   u32 retries_long;   // number of long data pkt retries
137} wifi_rate_stat;
138
139/* access categories */
140typedef enum {
141   WIFI_AC_VO  = 0,
142   WIFI_AC_VI  = 1,
143   WIFI_AC_BE  = 2,
144   WIFI_AC_BK  = 3,
145   WIFI_AC_MAX = 4,
146} wifi_traffic_ac;
147
148/* wifi peer type */
149typedef enum
150{
151   WIFI_PEER_STA,
152   WIFI_PEER_AP,
153   WIFI_PEER_P2P_GO,
154   WIFI_PEER_P2P_CLIENT,
155   WIFI_PEER_NAN,
156   WIFI_PEER_TDLS,
157   WIFI_PEER_INVALID,
158} wifi_peer_type;
159
160/* per peer statistics */
161typedef struct {
162   wifi_peer_type type;           // peer type (AP, TDLS, GO etc.)
163   u8 peer_mac_address[6];        // mac address
164   u32 capabilities;              // peer WIFI_CAPABILITY_XXX
165   u32 num_rate;                  // number of rates
166   wifi_rate_stat rate_stats[];   // per rate statistics, number of entries  = num_rate
167} wifi_peer_info;
168
169/* Per access category statistics */
170typedef struct {
171   wifi_traffic_ac ac;             // access category (VI, VO, BE, BK)
172   u32 tx_mpdu;                    // number of successfully transmitted unicast data pkts (ACK rcvd)
173   u32 rx_mpdu;                    // number of received unicast data packets
174   u32 tx_mcast;                   // number of succesfully transmitted multicast data packets
175                                   // STA case: implies ACK received from AP for the unicast packet in which mcast pkt was sent
176   u32 rx_mcast;                   // number of received multicast data packets
177   u32 rx_ampdu;                   // number of received unicast a-mpdus; support of this counter is optional
178   u32 tx_ampdu;                   // number of transmitted unicast a-mpdus; support of this counter is optional
179   u32 mpdu_lost;                  // number of data pkt losses (no ACK)
180   u32 retries;                    // total number of data pkt retries
181   u32 retries_short;              // number of short data pkt retries
182   u32 retries_long;               // number of long data pkt retries
183   u32 contention_time_min;        // data pkt min contention time (usecs)
184   u32 contention_time_max;        // data pkt max contention time (usecs)
185   u32 contention_time_avg;        // data pkt avg contention time (usecs)
186   u32 contention_num_samples;     // num of data pkts used for contention statistics
187} wifi_wmm_ac_stat;
188
189/* interface statistics */
190typedef struct {
191   wifi_interface_handle iface;          // wifi interface
192   wifi_interface_link_layer_info info;  // current state of the interface
193   u32 beacon_rx;                        // access point beacon received count from connected AP
194   u64 average_tsf_offset;               // average beacon offset encountered (beacon_TSF - TBTT)
195                                         // The average_tsf_offset field is used so as to calculate the
196                                         // typical beacon contention time on the channel as well may be
197                                         // used to debug beacon synchronization and related power consumption issue
198   u32 leaky_ap_detected;                // indicate that this AP typically leaks packets beyond the driver guard time.
199   u32 leaky_ap_avg_num_frames_leaked;  // average number of frame leaked by AP after frame with PM bit set was ACK'ed by AP
200   u32 leaky_ap_guard_time;              // guard time currently in force (when implementing IEEE power management based on
201                                         // frame control PM bit), How long driver waits before shutting down the radio and
202                                         // after receiving an ACK for a data frame with PM bit set)
203   u32 mgmt_rx;                          // access point mgmt frames received count from connected AP (including Beacon)
204   u32 mgmt_action_rx;                   // action frames received count
205   u32 mgmt_action_tx;                   // action frames transmit count
206   wifi_rssi rssi_mgmt;                  // access Point Beacon and Management frames RSSI (averaged)
207   wifi_rssi rssi_data;                  // access Point Data Frames RSSI (averaged) from connected AP
208   wifi_rssi rssi_ack;                   // access Point ACK RSSI (averaged) from connected AP
209   wifi_wmm_ac_stat ac[WIFI_AC_MAX];     // per ac data packet statistics
210   u32 num_peers;                        // number of peers
211   wifi_peer_info peer_info[];           // per peer statistics
212} wifi_iface_stat;
213
214/* configuration params */
215typedef struct {
216   u32 mpdu_size_threshold;             // threshold to classify the pkts as short or long
217                                        // packet size < mpdu_size_threshold => short
218   u32 aggressive_statistics_gathering; // set for field debug mode. Driver should collect all statistics regardless of performance impact.
219} wifi_link_layer_params;
220
221/* API to trigger the link layer statistics collection.
222   Unless his API is invoked - link layer statistics will not be collected.
223   Radio statistics (once started) do not stop or get reset unless wifi_clear_link_stats is invoked
224   Interface statistics (once started) reset and start afresh after each connection */
225wifi_error wifi_set_link_stats(wifi_interface_handle iface, wifi_link_layer_params params);
226
227/* callback for reporting link layer stats */
228typedef struct {
229  void (*on_link_stats_results) (wifi_request_id id, wifi_iface_stat *iface_stat,
230         int num_radios, wifi_radio_stat *radio_stat);
231} wifi_stats_result_handler;
232
233/* api to collect the link layer statistics for a given iface and all the radio stats */
234wifi_error wifi_get_link_stats(wifi_request_id id,
235        wifi_interface_handle iface, wifi_stats_result_handler handler);
236
237/* wifi statistics bitmap  */
238#define WIFI_STATS_RADIO              0x00000001      // all radio statistics
239#define WIFI_STATS_RADIO_CCA          0x00000002      // cca_busy_time (within radio statistics)
240#define WIFI_STATS_RADIO_CHANNELS     0x00000004      // all channel statistics (within radio statistics)
241#define WIFI_STATS_RADIO_SCAN         0x00000008      // all scan statistics (within radio statistics)
242#define WIFI_STATS_IFACE              0x00000010      // all interface statistics
243#define WIFI_STATS_IFACE_TXRATE       0x00000020      // all tx rate statistics (within interface statistics)
244#define WIFI_STATS_IFACE_AC           0x00000040      // all ac statistics (within interface statistics)
245#define WIFI_STATS_IFACE_CONTENTION   0x00000080      // all contention (min, max, avg) statistics (within ac statisctics)
246
247/* clear api to reset statistics, stats_clear_rsp_mask identifies what stats have been cleared
248   stop_req = 1 will imply whether to stop the statistics collection.
249   stop_rsp = 1 will imply that stop_req was honored and statistics collection was stopped.
250 */
251wifi_error wifi_clear_link_stats(wifi_interface_handle iface,
252      u32 stats_clear_req_mask, u32 *stats_clear_rsp_mask, u8 stop_req, u8 *stop_rsp);
253
254#ifdef __cplusplus
255}
256#endif /* __cplusplus */
257
258#endif /*__WIFI_HAL_STATS_ */
259
260