| 0be7d969b0efef085ed6497d462ba16a875ca737 |
|
24-Dec-2013 |
Kevin Hao <haokexin@gmail.com> |
powerpc/fsl_booke: smp support for booting a relocatable kernel above 64M
When booting above the 64M for a secondary cpu, we also face the
same issue as the boot cpu that the PAGE_OFFSET map two different
physical address for the init tlb and the final map. So we have to use
switch_to_as1/restore_to_as0 between the conversion of these two
maps. When restoring to as0 for a secondary cpu, we only need to
return to the caller. So add a new parameter for function
restore_to_as0 for this purpose.
Use LOAD_REG_ADDR_PIC to get the address of variables which may
be used before we set the final map in cams for the secondary cpu.
Move the setting of cams a bit earlier in order to avoid the
unnecessary using of LOAD_REG_ADDR_PIC.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
| 7d2471f9fa85089beb1cb9436ffc28f9e11e518d |
|
24-Dec-2013 |
Kevin Hao <haokexin@gmail.com> |
powerpc/fsl_booke: make sure PAGE_OFFSET map to memstart_addr for relocatable kernel
This is always true for a non-relocatable kernel. Otherwise the kernel
would get stuck. But for a relocatable kernel, it seems a little
complicated. When booting a relocatable kernel, we just align the
kernel start addr to 64M and map the PAGE_OFFSET from there. The
relocation will base on this virtual address. But if this address
is not the same as the memstart_addr, we will have to change the
map of PAGE_OFFSET to the real memstart_addr and do another relocation
again.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
[scottwood@freescale.com: make offset long and non-negative in simple case]
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
| 78a235efdc42ff363de81fdbc171385e8b86b69b |
|
24-Dec-2013 |
Kevin Hao <haokexin@gmail.com> |
powerpc/fsl_booke: set the tlb entry for the kernel address in AS1
We use the tlb1 entries to map low mem to the kernel space. In the
current code, it assumes that the first tlb entry would cover the
kernel image. But this is not true for some special cases, such as
when we run a relocatable kernel above the 64M or set
CONFIG_KERNEL_START above 64M. So we choose to switch to address
space 1 before setting these tlb entries.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
| 1dc91c3eb374ca01ec99dc0ca2a38babc509beb3 |
|
16-Sep-2011 |
Kumar Gala <galak@kernel.crashing.org> |
powerpc/fsl-booke: Fix setup_initial_memory_limit to not blindly map
On FSL Book-E devices we support multiple large TLB sizes and so we can
get into situations in which the initial 1G TLB size is too big and
we're asked for a size that is not mappable by a single entry (like
512M). The single entry is important because when we bring up secondary
cores they need to ensure any data structure they need to access (eg
PACA or stack) is always mapped.
So we really need to determine what size will actually be mapped by the
first TLB entry to ensure we limit early memory references to that
region. We refactor the map_mem_in_cams() code to provider a helper
function that we can utilize to determine the size of the first TLB
entry while taking into account size and alignment constraints.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
| 55fd766b5fad8240b7a6e994b5779a46d28f73d4 |
|
17-Oct-2009 |
Kumar Gala <galak@kernel.crashing.org> |
powerpc/fsl-booke64: Use TLB CAMs to cover linear mapping on FSL 64-bit chips
On Freescale parts typically have TLB array for large mappings that we can
bolt the linear mapping into. We utilize the code that already exists
on PPC32 on the 64-bit side to setup the linear mapping to be cover by
bolted TLB entries. We utilize a quarter of the variable size TLB array
for this purpose.
Additionally, we limit the amount of memory to what we can cover via
bolted entries so we don't get secondary faults in the TLB miss
handlers. We should fix this limitation in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
| 78f622377f7d31d988db350a43c5689dd5f31876 |
|
13-May-2010 |
Kumar Gala <galak@kernel.crashing.org> |
powerpc/fsl-booke: Move loadcam_entry back to asm code to fix SMP ftrace
When we build with ftrace enabled its possible that loadcam_entry would
have used the stack pointer (even though the code doesn't need it). We
call loadcam_entry in __secondary_start before the stack is setup. To
ensure that loadcam_entry doesn't use the stack pointer the easiest
solution is to just have it in asm code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
| 500a0e56c36dabb8cb0d8f3c93aac900058ef7af |
|
13-May-2010 |
Kumar Gala <galak@kernel.crashing.org> |
powerpc/fsl-booke: Move loadcam_entry back to asm code to fix SMP ftrace
When we build with ftrace enabled its possible that loadcam_entry would
have used the stack pointer (even though the code doesn't need it). We
call loadcam_entry in __secondary_start before the stack is setup. To
ensure that loadcam_entry doesn't use the stack pointer the easiest
solution is to just have it in asm code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
| e7f75ad01d590243904c2d95ab47e6b2e9ef6dad |
|
05-Mar-2010 |
Dave Kleikamp <shaggy@linux.vnet.ibm.com> |
powerpc/47x: Base ppc476 support
This patch adds the base support for the 476 processor. The code was
primarily written by Ben Herrenschmidt and Torez Smith, but I've been
maintaining it for a while.
The goal is to have a single binary that will run on 44x and 47x, but
we still have some details to work out. The biggest is that the L1 cache
line size differs on the two platforms, but it's currently a compile-time
option.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Torez Smith <lnxtorez@linux.vnet.ibm.com>
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
| ae4cec4736969ec2196a6bbce4ab263ff7cb7eef |
|
14-Dec-2009 |
Stephen Rothwell <sfr@canb.auug.org.au> |
powerpc: fix up for mmu_mapin_ram api change
Today's linux-next build (powerpc ppc44x_defconfig) failed like this:
arch/powerpc/mm/pgtable_32.c: In function 'mapin_ram':
arch/powerpc/mm/pgtable_32.c:318: error: too many arguments to function 'mmu_mapin_ram'
Casued by commit de32400dd26e743c5d500aa42d8d6818b79edb73 ("wii: use both
mem1 and mem2 as ram").
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
| c5df7f775148723de39274537a886e9502eef336 |
|
12-Dec-2009 |
Albert Herranz <albert_herranz@yahoo.es> |
powerpc: allow ioremap within reserved memory regions
Add a flag to let a platform ioremap memory regions marked as reserved.
This flag will be used later by the Nintendo Wii support code to allow
ioremapping the I/O region sitting between MEM1 and MEM2 and marked
as reserved RAM in the patch "wii: use both mem1 and mem2 as ram".
This will no longer be needed when proper discontig memory support
for 32-bit PowerPC is added to the kernel.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
| de32400dd26e743c5d500aa42d8d6818b79edb73 |
|
12-Dec-2009 |
Albert Herranz <albert_herranz@yahoo.es> |
wii: use both mem1 and mem2 as ram
The Nintendo Wii video game console has two discontiguous RAM regions:
- MEM1: 24MB @ 0x00000000
- MEM2: 64MB @ 0x10000000
Unfortunately, the kernel currently does not support discontiguous RAM
memory regions on 32-bit PowerPC platforms.
This patch adds a series of workarounds to allow the use of the second
memory region (MEM2) as RAM by the kernel.
Basically, a single range of memory from the beginning of MEM1 to the
end of MEM2 is reported to the kernel, and a memory reservation is
created for the hole between MEM1 and MEM2.
With this patch the system is able to use all the available RAM and not
just ~27% of it.
This will no longer be needed when proper discontig memory support
for 32-bit PowerPC is added to the kernel.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
| 8b27f0b61db57f5555fc2d3fc95c3ea9fd1a9d6c |
|
15-Oct-2009 |
Kumar Gala <galak@kernel.crashing.org> |
powerpc/fsl-booke: Rework TLB CAM code
Re-write the code so its more standalone and fixed some issues:
* Bump'd # of CAM entries to 64 to support e500mc
* Make the code handle MAS7 properly
* Use pr_cont instead of creating a string as we go
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
| 32a74949b7337726e76d69f51c48715431126c6c |
|
24-Jul-2009 |
Benjamin Herrenschmidt <benh@kernel.crashing.org> |
powerpc/mm: Add support for SPARSEMEM_VMEMMAP on 64-bit Book3E
The base TLB support didn't include support for SPARSEMEM_VMEMMAP, though
we did carve out some virtual space for it, the necessary support code
wasn't there. This implements it by using 16M pages for now, though the
page size could easily be changed at runtime if necessary.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| 25d21ad6e799cccd097b9df2a2fefe19a7e1dfcf |
|
24-Jul-2009 |
Benjamin Herrenschmidt <benh@kernel.crashing.org> |
powerpc: Add TLB management code for 64-bit Book3E
This adds the TLB miss handler assembly, the low level TLB flush routines
along with the necessary hook for dealing with our virtual page tables
or indirect TLB entries that need to be flushes when PTE pages are freed.
There is currently no support for hugetlbfs
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| d4e167da4cb60910f6ac305aee03714937f70b71 |
|
24-Jul-2009 |
Benjamin Herrenschmidt <benh@kernel.crashing.org> |
powerpc/mm: Make low level TLB flush ops on BookE take additional args
We need to pass down whether the page is direct or indirect and we'll
need to pass the page size to _tlbil_va and _tlbivax_bcast
We also add a new low level _tlbil_pid_noind() which does a TLB flush
by PID but avoids flushing indirect entries if possible
This implements those new prototypes but defines them with inlines
or macros so that no additional arguments are actually passed on current
processors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| 4a0826824beb28390651a962987b0681b9e7fe93 |
|
06-Jan-2009 |
Benjamin Herrenschmidt <benh@kernel.crashing.org> |
powerpc: Fix missing semicolons in mmu_decl.h
This is a brown paper bag from one of my earlier patches that
breaks build on 40x and 8xx.
And yes, I've now added 40x and 8xx to my list of test configs :-)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
| 6fd8be4bf72879b3039654388e985cabf8449af5 |
|
09-Dec-2008 |
Trent Piepho <tpiepho@freescale.com> |
powerpc/fsl-booke: Remove num_tlbcam_entries
This is a global variable defined in fsl_booke_mmu.c with a value that gets
initialized in assembly code in head_fsl_booke.S.
It's never used.
If some code ever does want to know the number of entries in TLB1, then
"numcams = mfspr(SPRN_TLB1CFG) & 0xfff", is a whole lot simpler than a
global initialized during kernel boot from assembly.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
| 19f5465e823858a2f0b0e9a92e52816ba3ee70bb |
|
09-Dec-2008 |
Trent Piepho <tpiepho@freescale.com> |
powerpc/fsl-booke: Don't hard-code size of struct tlbcam
Some assembly code in head_fsl_booke.S hard-coded the size of struct tlbcam
to 20 when it indexed the TLBCAM table. Anyone changing the size of struct
tlbcam would not know to expect that.
The kernel already has a system to get the size of C structures into
assembly language files, asm-offsets, so let's use it.
The definition of the struct gets moved to a header, so that asm-offsets.c
can include it.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
| 2a4aca1144394653269720ffbb5a325a77abd5fa |
|
18-Dec-2008 |
Benjamin Herrenschmidt <benh@kernel.crashing.org> |
powerpc/mm: Split low level tlb invalidate for nohash processors
Currently, the various forms of low level TLB invalidations are all
implemented in misc_32.S for 32-bit processors, in a fairly scary
mess of #ifdef's and with interesting duplication such as a whole
bunch of code for FSL _tlbie and _tlbia which are no longer used.
This moves things around such that _tlbie is now defined in
hash_low_32.S and is only used by the 32-bit hash code, and all
nohash CPUs use the various _tlbil_* forms that are now moved to
a new file, tlb_nohash_low.S.
I moved all the definitions for that stuff out of
include/asm/tlbflush.h as they are really internal mm stuff, into
mm/mmu_decl.h
The code should have no functional changes. I kept some variants
inline for trivial forms on things like 40x and 8xx.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| f63837f0581fe580168ae1a7d178ded935411747 |
|
14-Dec-2008 |
Benjamin Herrenschmidt <benh@kernel.crashing.org> |
powerpc/mm: Remove flush_HPTE()
The function flush_HPTE() is used in only one place, the implementation
of DEBUG_PAGEALLOC on ppc32.
It's actually a dup of flush_tlb_page() though it's -slightly- more
efficient on hash based processors. We remove it and replace it by
a direct call to the hash flush code on those processors and to
flush_tlb_page() for everybody else.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| 2bf3016f89344d4cd8b2c96bbec2b642a2bde413 |
|
09-Jul-2008 |
Stefan Roese <sr@denx.de> |
powerpc: Fix problems with 32bit PPC's running with >= 4GB of RAM
This patch enables 32bit PPC's (with 36bit physical address space, e.g.
IBM/AMCC PPC44x) to run with >= 4GB of RAM. Mostly its just replacing types
(unsigned long -> phys_addr_t).
Tested on an AMCC Katmai with 4GB of DDR2.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
| 7c5c4325d2d911fe54db3bc14149bfa558ae0acb |
|
14-Jun-2008 |
Becky Bruce <becky.bruce@freescale.com> |
powerpc: Change BAT code to use phys_addr_t
Currently, the physical address is an unsigned long, but it should
be phys_addr_t in set_bat, [v/p]_mapped_by_bat. Also, create a
macro that can convert a large physical address into the correct
format for programming the BAT registers.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| 09b5e63f827016732d956abb7a4c74a312d20521 |
|
15-Apr-2008 |
Kumar Gala <galak@kernel.crashing.org> |
[POWERPC] Rename __initial_memory_limit to __initial_memory_limit_addr
We always use __initial_memory_limit as an address so rename it
to be clear.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| d7917ba7051e3fd12ebe2d5a09b29fb3a2b38190 |
|
15-Apr-2008 |
Kumar Gala <galak@kernel.crashing.org> |
[POWERPC] Introduce lowmem_end_addr to distinguish from total_lowmem
total_lowmem represents the amount of low memory, not the physical
address that low memory ends at. If the start of memory is at 0 it
happens that total_lowmem can be used as both the size and the address
that lowmem ends at (or more specifically one byte beyond the end).
To make the code a bit more clear and deal with the case when the start of
memory isn't at physical 0, we introduce lowmem_end_addr that represents
one byte beyond the last physical address in the lowmem region.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| 99c62dd773797b68f3b1ca6bb3274725d1852fa2 |
|
15-Apr-2008 |
Kumar Gala <galak@kernel.crashing.org> |
[POWERPC] Remove and replace uses of PPC_MEMSTART with memstart_addr
A number of users of PPC_MEMSTART (40x, ppc_mmu_32) can just always
use 0 as we don't support booting these kernels at non-zero physical
addresses since their exception vectors must be at 0 (or 0xfffx_xxxx).
For the sub-arches that support relocatable interrupt vectors
(book-e), it's reasonable to have memory start at a non-zero physical
address. For those cases use the variable memstart_addr instead of
the #define PPC_MEMSTART since the only uses of PPC_MEMSTART are for
initialization and in the future we can set memstart_addr at runtime
to have a relocatable kernel.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| 0b47759db54f82df68ed179ddc5cb2becea56158 |
|
20-Nov-2007 |
Benjamin Herrenschmidt <benh@kernel.crashing.org> |
[POWERPC] Fix 8xx build breakage due to _tlbie changes
My changes to _tlbie to fix 4xx unfortunately broke 8xx build in a
couple of places. This fixes it.
Spotted by Olof Johansson.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| e701d269aa28996f3502780951fe1b12d5d66b49 |
|
29-Oct-2007 |
Benjamin Herrenschmidt <benh@kernel.crashing.org> |
[POWERPC] 4xx: Fix 4xx flush_tlb_page()
On 4xx CPUs, the current implementation of flush_tlb_page() uses
a low level _tlbie() assembly function that only works for the
current PID. Thus, invalidations caused by, for example, a COW
fault triggered by get_user_pages() from a different context will
not work properly, causing among other things, gdb breakpoints
to fail.
This patch adds a "pid" argument to _tlbie() on 4xx processors,
and uses it to flush entries in the right context. FSL BookE
also gets the argument but it seems they don't need it (their
tlbivax form ignores the PID when invalidating according to the
document I have).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
|
| 8e561e7eda02819c711a75b64a000bf34948cdbb |
|
13-Jun-2007 |
David Gibson <david@gibson.dropbear.id.au> |
[POWERPC] Kill typedef-ed structs for hash PTEs and BATs
Using typedefs to rename structure types if frowned on by CodingStyle.
However, we do so for the hash PTE structure on both ppc32 (where it's
called "PTE") and ppc64 (where it's called "hpte_t"). On ppc32 we
also have such a typedef for the BATs ("BAT").
This removes this unhelpful use of typedefs, in the process
bringing ppc32 and ppc64 closer together, by using the name "struct
hash_pte" in both cases.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| f21f49ea639ac3f24824177dac1268af75a2d373 |
|
13-Jun-2007 |
David Gibson <david@gibson.dropbear.id.au> |
[POWERPC] Remove the dregs of APUS support from arch/powerpc
APUS (the Amiga Power-Up System) is not supported under arch/powerpc
and it's unlikely it ever will be. Therefore, this patch removes the
fragments of APUS support code from arch/powerpc which have been
copied from arch/ppc.
A few APUS references are left in asm-powerpc in .h files which are
still used from arch/ppc.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| 3d5134ee8341bffc4f539049abb9e90d469b448d |
|
04-Jun-2007 |
Benjamin Herrenschmidt <benh@kernel.crashing.org> |
[POWERPC] Rewrite IO allocation & mapping on powerpc64
This rewrites pretty much from scratch the handling of MMIO and PIO
space allocations on powerpc64. The main goals are:
- Get rid of imalloc and use more common code where possible
- Simplify the current mess so that PIO space is allocated and
mapped in a single place for PCI bridges
- Handle allocation constraints of PIO for all bridges including
hot plugged ones within the 2GB space reserved for IO ports,
so that devices on hotplugged busses will now work with drivers
that assume IO ports fit in an int.
- Cleanup and separate tracking of the ISA space in the reserved
low 64K of IO space. No ISA -> Nothing mapped there.
I booted a cell blade with IDE on PIO and MMIO and a dual G5 so
far, that's it :-)
With this patch, all allocations are done using the code in
mm/vmalloc.c, though we use the low level __get_vm_area with
explicit start/stop constraints in order to manage separate
areas for vmalloc/vmap, ioremap, and PCI IOs.
This greatly simplifies a lot of things, as you can see in the
diffstat of that patch :-)
A new pair of functions pcibios_map/unmap_io_space() now replace
all of the previous code that used to manipulate PCI IOs space.
The allocation is done at mapping time, which is now called from
scan_phb's, just before the devices are probed (instead of after,
which is by itself a bug fix). The only other caller is the PCI
hotplug code for hot adding PCI-PCI bridges (slots).
imalloc is gone, as is the "sub-allocation" thing, but I do beleive
that hotplug should still work in the sense that the space allocation
is always done by the PHB, but if you unmap a child bus of this PHB
(which seems to be possible), then the code should properly tear
down all the HPTE mappings for that area of the PHB allocated IO space.
I now always reserve the first 64K of IO space for the bridge with
the ISA bus on it. I have moved the code for tracking ISA in a separate
file which should also make it smarter if we ever are capable of
hot unplugging or re-plugging an ISA bridge.
This should have a side effect on platforms like powermac where VGA IOs
will no longer work. This is done on purpose though as they would have
worked semi-randomly before. The idea at this point is to isolate drivers
that might need to access those and fix them by providing a proper
function to obtain an offset to the legacy IOs of a given bus.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| 57d7909e0d2dd54567ae775e22b14076b777042a |
|
30-Apr-2007 |
David Gibson <david@gibson.dropbear.id.au> |
[POWERPC] Revise PPC44x MMU code for arch/powerpc
This patch takes the definitions for the PPC44x MMU (a software loaded
TLB) from asm-ppc/mmu.h, cleans them up of things no longer necessary
in arch/powerpc and puts them in a new asm-powerpc/mmu_44x.h file. It
also substantially simplifies arch/powerpc/mm/44x_mmu.c and makes a
couple of small fixes necessary for the 44x MMU code to build and work
properly in arch/powerpc.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| 621023072524fc0155ed16490255e1ea3aa11585 |
|
24-Apr-2007 |
David Gibson <david@gibson.dropbear.id.au> |
[POWERPC] Cleanup and fix breakage in tlbflush.h
BenH's commit a741e67969577163a4cfc78d7fd2753219087ef1 in powerpc.git,
although (AFAICT) only intended to affect ppc64, also has side-effects
which break 44x. I think 40x, 8xx and Freescale Book E are also
affected, though I haven't tested them.
The problem lies in unconditionally removing flush_tlb_pending() from
the versions of flush_tlb_mm(), flush_tlb_range() and
flush_tlb_kernel_range() used on ppc64 - which are also used the
embedded platforms mentioned above.
The patch below cleans up the convoluted #ifdef logic in tlbflush.h,
in the process restoring the necessary flushes for the software TLB
platforms. There are three sets of definitions for the flushing
hooks: the software TLB versions (revised to avoid using names which
appear to related to TLB batching), the 32-bit hash based versions
(external functions) amd the 64-bit hash based versions (which
implement batching).
It also moves the declaration of update_mmu_cache() to always be in
tlbflush.h (previously it was in tlbflush.h except for PPC64, where it
was in pgtable.h).
Booted on Ebony (440GP) and compiled for 64-bit and 32-bit
multiplatform.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| ee4f2ea48674b6c9d91bc854edc51a3e6a7168c4 |
|
12-Apr-2007 |
Benjamin Herrenschmidt <benh@kernel.crashing.org> |
[POWERPC] Fix 32-bit mm operations when not using BATs
On hash table based 32 bits powerpc's, the hash management code runs with
a big spinlock. It's thus important that it never causes itself a hash
fault. That code is generally safe (it does memory accesses in real mode
among other things) with the exception of the actual access to the code
itself. That is, the kernel text needs to be accessible without taking
a hash miss exceptions.
This is currently guaranteed by having a BAT register mapping part of the
linear mapping permanently, which includes the kernel text. But this is
not true if using the "nobats" kernel command line option (which can be
useful for debugging) and will not be true when using DEBUG_PAGEALLOC
implemented in a subsequent patch.
This patch fixes this by pre-faulting in the hash table pages that hit
the kernel text, and making sure we never evict such a page under hash
pressure.
Signed-off-by: Benjamin Herrenchmidt <benh@kernel.crashing.org>
arch/powerpc/mm/hash_low_32.S | 22 ++++++++++++++++++++--
arch/powerpc/mm/mem.c | 3 ---
arch/powerpc/mm/mmu_decl.h | 4 ++++
arch/powerpc/mm/pgtable_32.c | 11 +++++++----
4 files changed, 31 insertions(+), 9 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| 800fc3eeb0eed3bf98d621c0da24d68cabcf6526 |
|
16-Nov-2005 |
David Gibson <david@gibson.dropbear.id.au> |
[PATCH] powerpc: Remove imalloc.h
asm-ppc64/imalloc.h is only included from files in arch/powerpc/mm.
We already have a header for mm local definitions,
arch/powerpc/mm/mmu_decl.h. Thus, this patch moves the contents of
imalloc.h into mmu_decl.h. The only exception are the definitions of
PHBS_IO_BASE, IMALLOC_BASE and IMALLOC_END. Those are moved into
pgtable.h, next to similar definitions of VMALLOC_START and
VMALLOC_SIZE.
Built for multiplatform 32bit and 64bit (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| ab1f9dac6eea25ee59e4c8e1cf0b7476afbbfe07 |
|
10-Oct-2005 |
Paul Mackerras <paulus@samba.org> |
powerpc: Merge arch/ppc64/mm to arch/powerpc/mm
This moves the remaining files in arch/ppc64/mm to arch/powerpc/mm,
and arranges that we use them when compiling with ARCH=ppc64.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| 7c8c6b9776fb41134d87ef50706a777a45d61cd4 |
|
05-Oct-2005 |
Paul Mackerras <paulus@samba.org> |
powerpc: Merge lmb.c and make MM initialization use it.
This also creates merged versions of do_init_bootmem, paging_init
and mem_init and moves them to arch/powerpc/mm/mem.c. It gets rid
of the mem_pieces stuff.
I made memory_limit a parameter to lmb_enforce_memory_limit rather
than a global referenced by that function. This will require some
small changes to ppc64 if we want to continue building ARCH=ppc64
using the merged lmb.c.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
| 14cf11af6cf608eb8c23e989ddb17a715ddce109 |
|
26-Sep-2005 |
Paul Mackerras <paulus@samba.org> |
powerpc: Merge enough to start building in arch/powerpc.
This creates the directory structure under arch/powerpc and a bunch
of Kconfig files. It does a first-cut merge of arch/powerpc/mm,
arch/powerpc/lib and arch/powerpc/platforms/powermac. This is enough
to build a 32-bit powermac kernel with ARCH=powerpc.
For now we are getting some unmerged files from arch/ppc/kernel and
arch/ppc/syslib, or arch/ppc64/kernel. This makes some minor changes
to files in those directories and files outside arch/powerpc.
The boot directory is still not merged. That's going to be interesting.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|