| d4ad30b182305ecf97f145a5d4d1fd9e728c6d01 |
|
02-Sep-2014 |
Govindarajulu Varadarajan <_govind@gmx.com> |
enic: Add tunable_ops support for rx_copybreak
This patch adds support for setting/getting rx_copybreak using
generic ethtool tunable.
Defines enic_get_tunable() & enic_set_tunable() to get/set rx_copybreak.
As of now, these two function supports only rx_copybreak.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 3762ff8f0e95f50f78d94e3f62e839103d1303aa |
|
21-Jul-2014 |
Govindarajulu Varadarajan <_govind@gmx.com> |
enic: Add ethtool support to show classifier filters added by the driver
This patch impliments ethtool_ops->get_rxnfc() to display the classifier
filter added by the driver.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| a16a3361927f75e6032df110920c83ca6c5045d3 |
|
02-Jul-2014 |
Govindarajulu Varadarajan <_govind@gmx.com> |
enic: fix return values in enic_set_coalesce
enic_set_coalesce() has two problems.
* It should return -EINVAL and not -EOPNOTSUPP for invalid coalesce values.
* In case of MSIX, enic_set_coalesce return error after applying requested
coalescing setting partially. We should either apply all the setting requeste
and return success or apply non and return error.
* This patch also simplifies the algo.
This was introduced by
'7c2ce6e60f703 enic: Add support for adaptive interrupt coalescing'
These changes were suggested by Ben Hutchings here
http://www.spinics.net/lists/netdev/msg283972.html
Also change enic driver version.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 537fae0101c8853abb52136788173dde74b9d1e9 |
|
06-Jun-2014 |
Jiri Pirko <jiri@resnulli.us> |
net: use SPEED_UNKNOWN and DUPLEX_UNKNOWN when appropriate
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 7c2ce6e60f7036de313a8c516ffe2aea889c738f |
|
19-May-2014 |
Sujith Sankar <ssujith@cisco.com> |
enic: Add support for adaptive interrupt coalescing
This patch adds support for adaptive interrupt coalescing.
For small pkts with low pkt rate, we can decrease the coalescing interrupt
dynamically which decreases the latency. This however increases the cpu
utilization. Based on testing with different coal intr and pkt rate we came up
with a table(mod_table) with rx_rate and coalescing interrupt value where we
get low latency without significant increase in cpu. mod_table table stores
the coalescing timer percentage value for different throughputs.
Function enic_calc_int_moderation() calculates the desired coalescing intr timer
value. This function is called in driver rx napi_poll. The actual value is set
by enic_set_int_moderation() which is called when napi_poll is complete. i.e
when we unmask the rx intr.
Adaptive coal intr is support only when driver is using msix intr. Because
intr is not shared.
Struct mod_range is used to store only the default adaptive coalescing intr
value.
Adaptive coal intr calue is calculated by
timer = range_start + ((rx_coal->range_end - range_start) *
mod_table[index].range_percent / 100);
rx_coal->range_end is the rx-usecs-high value set using ethtool.
range_start is rx-usecs-low, set using ethtool, if rx_small_pkt_bytes_cnt is
greater than 2 * rx_large_pkt_bytes_cnt. i.e small pkts are dominant. Else its
rx-usecs-low + 3.
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Neel Patel <neepatel@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 7ad24ea4bf620a32631d7b3069c3e30c078b0c3e |
|
11-May-2014 |
Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de> |
net: get rid of SET_ETHTOOL_OPS
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| f13bbc2f9aba00c7a37b499d23060616b9a4ef9e |
|
22-Jul-2013 |
Neel Patel <neepatel@cisco.com> |
drivers/net: enic: Move ethtool code to a separate file
This patch moves all enic ethtool hooks from enic_main.c to a new file
enic_ethtool.c
Signed-off-by: Neel Patel <neepatel@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|