| a4f2dacbf2a5045e34b98a35d9a3857800f25a7b |
|
30-Oct-2014 |
Or Gerlitz <ogerlitz@mellanox.com> |
net/mlx4_en: Don't attempt to TX offload the outer UDP checksum for VXLAN
For VXLAN/NVGRE encapsulation, the current HW doesn't support offloading
both the outer UDP TX checksum and the inner TCP/UDP TX checksum.
The driver doesn't advertize SKB_GSO_UDP_TUNNEL_CSUM, however we are wrongly
telling the HW to offload the outer UDP checksum for encapsulated packets,
fix that.
Fixes: 837052d0ccc5 ('net/mlx4_en: Add netdev support for TCP/IP
offloads of vxlan tunneling')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 535114539bb2c081b6680cb5a34be17e7b45df37 |
|
08-Oct-2014 |
Eric Dumazet <edumazet@google.com> |
net: add netdev_txq_bql_{enqueue, complete}_prefetchw() helpers
Add two helpers so that drivers do not have to care of BQL being
available or not.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jim Davis <jim.epost@gmail.com>
Fixes: 29d40c903247 ("net/mlx4_en: Use prefetch in tx path")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| fe971b95c22578456ff7198537827841c726d3f7 |
|
06-Oct-2014 |
Eric Dumazet <edumazet@google.com> |
net/mlx4_en: remove NETDEV_TX_BUSY
Drivers should avoid NETDEV_TX_BUSY as much as possible.
They should stop the tx queue before qdisc even tries to push another
packet, to avoid requeues.
For a driver supporting skb->xmit_more, this is likely to be a prereq
anyway, otherwise we could have a tx deadlock : We need to force a
doorbell if TX ring is full.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 1556b8746e52501fdfaadd65837baaa63a9fa937 |
|
04-Oct-2014 |
Eric Dumazet <edumazet@google.com> |
net/mlx4_en: Use the new tx_copybreak to set inline threshold
Instead of setting inline threshold using module parameter only on
driver load, use set_tunable() to set it dynamically.
No need to store the threshold per ring, using instead the netdev global
priv->prof->inline_thold
Initial value still is set using the module parameter, therefore
backward compatability is kept.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| acea73d671b25bfbbe6b8ceef949f4ac62c260c0 |
|
04-Oct-2014 |
Eric Dumazet <edumazet@google.com> |
net/mlx4_en: Enable the compiler to make is_inline() inlined
Reorganize code to call is_inline() once, so compiler can inline it
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| e70602a8b87649e9f7742d96929a8d83618fa320 |
|
04-Oct-2014 |
Eric Dumazet <edumazet@google.com> |
net/mlx4_en: tx_info->ts_requested was not cleared
Properly clear tx_info->ts_requested
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| e533ac7ea00c39f5ef4ab0976dd2662d50fa42a1 |
|
04-Oct-2014 |
Eric Dumazet <edumazet@google.com> |
net/mlx4_en: Use local var for skb_headlen(skb)
Access skb_headlen() once in tx flow
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| b9d8839a44092cb4268ef2813c34d5dbf3363603 |
|
04-Oct-2014 |
Eric Dumazet <edumazet@google.com> |
net/mlx4_en: Use local var in tx flow for skb_shinfo(skb)
Acces skb_shinfo(skb) once in tx flow.
Also, rename @i variable to @i_frag to avoid confusion, as the "goto
tx_drop_unmap;" relied on this @i variable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| f905c79e12791d09bbfd9ba7b672fbeb19c1e7c2 |
|
04-Oct-2014 |
Eric Dumazet <edumazet@google.com> |
net/mlx4_en: mlx4_en_xmit() reads ring->cons once, and ahead of time to avoid stalls
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| fb1843ee72c7b2ed784bf88ad79c6ccc2f652499 |
|
04-Oct-2014 |
Eric Dumazet <edumazet@google.com> |
net/mlx4_en: Avoid false sharing in mlx4_en_en_process_tx_cq()
mlx4_en_process_tx_cq() carefully fetches and writes ring->last_nr_txbb
and ring->cons only one time to avoid false sharing
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 29d40c903247596c954446639116467eb6689bb7 |
|
04-Oct-2014 |
Eric Dumazet <edumazet@google.com> |
net/mlx4_en: Use prefetch in tx path
mlx4_en_free_tx_desc() uses a prefetchw(&skb->users) to speed up
consume_skb()
prefetchw(&ring->tx_queue->dql) to speed up BQL update
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 3d03641cb4ea050f969dd3ab34113adb95287f36 |
|
04-Oct-2014 |
Eric Dumazet <edumazet@google.com> |
net/mlx4_en: Avoid a cache line miss in TX completion for single frag skb's
Add frag0_dma/frag0_byte_count into mlx4_en_tx_info to avoid a cache
line miss in TX completion for frames having one dma element. (We avoid
reading back the tx descriptor)
Note this could be extended to 2/3 dma elements later, as we have free
room in mlx4_en_tx_info
Also, mlx4_en_free_tx_desc() no longer accesses skb_shinfo(). We use a
new nr_maps fields in mlx4_en_tx_info to avoid 2 or 3 cache misses.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| dc9b06d156cefb95f7f6a3ac0521a3efa31d6805 |
|
04-Oct-2014 |
Eric Dumazet <edumazet@google.com> |
net/mlx4_en: tx_info allocated with kmalloc() instead of vmalloc()
Try to allocate using kmalloc_node() first, only on failure use
vmalloc()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 6a4e81211f475561ed87c613216f981fbef8b7fc |
|
04-Oct-2014 |
Eric Dumazet <edumazet@google.com> |
net/mlx4_en: Avoid calling bswap in tx fast path
- doorbell_qpn is stored in the cpu_to_be32() way to avoid bswap() in fast
path.
- mdev->mr.key stored in ring->mr_key to also avoid bswap() and access to
cold cache line.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 7dfa4b414d4eec8da56e44fb2b4aea3e549b092f |
|
04-Oct-2014 |
Eric Dumazet <edumazet@google.com> |
net/mlx4_en: Code cleanups in tx path
- Remove unused variable ring->poll_cnt
- No need to set some fields if using blueflame
- Add missing const's
- Use unlikely
- Remove unneeded new line
- Make some comments more precise
- struct mlx4_bf @offset field reduced to unsigned int to save space
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 9fab426de78140dc5cb0b85bbee6042c9c3d5ca5 |
|
02-Oct-2014 |
Eric Dumazet <edumazet@google.com> |
mlx4: add a new xmit_more counter
ethtool -S reports a new counter, tracking number of time doorbell
was not triggered, because skb->xmit_more was set.
$ ethtool -S eth0 | egrep "tx_packet|xmit_more"
tx_packets: 2413288400
xmit_more: 666121277
I merged the tso_packet false sharing avoidance in this patch as well.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 5804283d7cb1da46485950d545dd7869137dcda5 |
|
25-Sep-2014 |
Eric Dumazet <edumazet@google.com> |
mlx4: exploit skb->xmit_more to conditionally send doorbell
skb->xmit_more tells us if another skb is coming next.
We need to send doorbell when : xmit_more is not set,
or txqueue is stopped (preventing next skb to come immediately)
Tested with a modified pktgen version, I got a 40% increase of
throughput.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| b1b6b4da7867d220f0da5f6686b869b304c5459b |
|
18-Sep-2014 |
Ido Shamay <idos@mellanox.com> |
net/mlx4_en: Add mlx4_en_get_cqe helper
This function derives the base address of the CQE from the CQE size,
and calculates the real CQE context segment in it from the factor
(this is like before). Before this change the code used the factor to
calculate the base address of the CQE as well.
The factor indicates in which segment of the cqe stride the cqe information
is located. For 32-byte strides, the segment is 0, and for 64 byte strides,
the segment is 1 (bytes 32..63). Using the factor was ok as long as we had
only 32 and 64 byte strides. However, with larger strides, the factor is zero,
and so cannot be used to calculate the base of the CQE.
The helper uses the same method of CQE buffer pulling made by all other
components that reads the CQE buffer (mlx4_ib driver and libmlx4).
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| b89df95d52d5fd0de5a2ca3f8b49aaaee4675151 |
|
03-Sep-2014 |
Rick Jones <rick.jones2@hp.com> |
mlx4_en: Convert the normal skb free path to dev_consume_skb_any()
It would appear the mlx4_en driver was still making a call to
dev_kfree_skb_any() where dev_consume_skb_any() would be more
appropriate. This should make dropped packet profiling/tracking
easier/better over a NIC driven by mlx4_en.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 0fef9d0308d4c524da716b4b669d8754594450b2 |
|
22-Jul-2014 |
Amir Vadai <amirv@mellanox.com> |
net/mlx4_en: Disable blueflame using ethtool private flags
Enable the user to turn off the hardware feature called BlueFlame.
Since it is something specific to mlx4_en hardware, we control
the feature via ethtool private flags.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| fbc6daf19745b372c0d909e5d74ab02e42b70e51 |
|
08-Jul-2014 |
Amir Vadai <amirv@mellanox.com> |
net/mlx4_en: Ignore budget on TX napi polling
It is recommended that TX work not count against the quota.
The cost of TX packet liberation is a minute percentage of what it costs to
process an RX frame. Furthermore, that SKB freeing makes memory available for
other paths in the stack.
Give the TX a larger budget and be more aggressive about cleaning up the Tx
descriptors this budget could be changed using ethtool:
$ ethtool -C eth1 tx-frames-irq <budget>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 35f6f45368632f21bd27559c44dbb1cab51d8947 |
|
29-Jun-2014 |
Amir Vadai <amirv@mellanox.com> |
net/mlx4_en: Don't use irq_affinity_notifier to track changes in IRQ affinity map
IRQ affinity notifier can only have a single notifier - cpu_rmap
notifier. Can't use it to track changes in IRQ affinity map.
Detect IRQ affinity changes by comparing CPU to current IRQ affinity map
during NAPI poll thread.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ben Hutchings <ben@decadent.org.uk>
Fixes: 2eacc23 ("net/mlx4_core: Enforce irq affinity changes immediatly")
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 40f2287bd583f4df4c602c1a29a48df2730fb6d4 |
|
11-May-2014 |
Jiri Kosina <jkosina@suse.cz> |
IB/mlx4: Implement IB_QP_CREATE_USE_GFP_NOIO
Modify the various routines used to allocate memory resources which
serve QPs in mlx4 to get an input GFP directive. Have the Ethernet
driver to use GFP_KERNEL in it's QP allocations as done prior to this
commit, and the IB driver to use GFP_NOIO when the IB verbs
IB_QP_CREATE_USE_GFP_NOIO QP creation flag is provided.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
| 2eacc23c422b4553030168f315cb49522fa1b1f6 |
|
13-May-2014 |
Yuval Atias <yuvala@mellanox.com> |
net/mlx4_core: Enforce irq affinity changes immediatly
During heavy traffic, napi is constatntly polling the complition queue
and no interrupt is fired. Because of that, changes to irq affinity are
ignored until traffic is stopped and resumed.
By registering to the irq notifier mechanism, and forcing interrupt when
affinity is changed, irq affinity changes will be immediatly enforced.
Signed-off-by: Yuval Atias <yuvala@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 1a91de28831a1bd913e14dacf25763f3672e24a9 |
|
07-May-2014 |
Joe Perches <joe@perches.com> |
mellanox: Logging message cleanups
Use a more current logging style.
o Coalesce formats
o Add missing spaces for coalesced formats
o Align arguments for modified formats
o Add missing newlines for some logging messages
o Use DRV_NAME as part of format instead of %s, DRV_NAME to
reduce overall text.
o Use ..., ##__VA_ARGS__ instead of args... in macros
o Correct a few format typos
o Use a single line message where appropriate
Signed-off-by: Joe Perches <joe@perches.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| e81f44b66b456a7dcfbdeffeb355458cd6a58973 |
|
11-Mar-2014 |
Eric W. Biederman <ebiederm@xmission.com> |
mlx4: Call dev_kfree_skby_any instead of dev_kfree_skb.
Replace dev_kfree_skb with dev_kfree_skb_any in functions that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| ec5709403e6893acb4f7ca40514ebd29c3116836 |
|
02-Mar-2014 |
Amir Vadai <amirv@mellanox.com> |
net/mlx4_en: Use union for BlueFlame WQE
When BlueFlame is turned on, control segment of the TX WQE is changed,
and the second line of it is used for QPN.
Changed code to use a union in the mlx4_wqe_ctrl_seg instead of casting.
This makes the code clearer and solves the static checker warning:
drivers/net/ethernet/mellanox/mlx4/en_tx.c:839 mlx4_en_xmit()
warn: potential memory corrupting cast 4 vs 2 bytes
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 15bffdffccb3204eb1e993f60eee65c439a03136 |
|
02-Mar-2014 |
Eugenia Emantayev <eugenia@mellanox.com> |
net/mlx4_en: Move queue stopped/waked counters to be per ring
Give accurate counters and avoids cache misses when several rings
update the counters of stop/wake queue.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 93591aaa62f89820f4ae0558f01eaf9a359738da |
|
02-Mar-2014 |
Eugenia Emantayev <eugenia@mellanox.com> |
net/mlx4_en: Pad ethernet packets smaller than 17 bytes
Hardware can't accept packets smaller than 17 bytes. Therefore need to
pad with zeros.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| b97b33a3df0439401f80f041eda507d4fffa0dbf |
|
02-Mar-2014 |
Eugenia Emantayev <eugenia@mellanox.com> |
net/mlx4_en: Verify mlx4_en module parameters
Verify mlx4_en module parameters.
In case they are out of range - reset to default values.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 99932d4fc03a13bb3e94938fe25458fabc8f2fc3 |
|
16-Feb-2014 |
Daniel Borkmann <dborkman@redhat.com> |
netdevice: add queue selection fallback handler for ndo_select_queue
Add a new argument for ndo_select_queue() callback that passes a
fallback handler. This gets invoked through netdev_pick_tx();
fallback handler is currently __netdev_pick_tx() as most drivers
invoke this function within their customized implementation in
case for skbs that don't need any special handling. This fallback
handler can then be replaced on other call-sites with different
queue selection methods (e.g. in packet sockets, pktgen etc).
This also has the nice side-effect that __netdev_pick_tx() is
then only invoked from netdev_pick_tx() and export of that
function to modules can be undone.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| f663dd9aaf9ed124f25f0f8452edf238f087ad50 |
|
10-Jan-2014 |
Jason Wang <jasowang@redhat.com> |
net: core: explicitly select a txq before doing l2 forwarding
Currently, the tx queue were selected implicitly in ndo_dfwd_start_xmit(). The
will cause several issues:
- NETIF_F_LLTX were removed for macvlan, so txq lock were done for macvlan
instead of lower device which misses the necessary txq synchronization for
lower device such as txq stopping or frozen required by dev watchdog or
control path.
- dev_hard_start_xmit() was called with NULL txq which bypasses the net device
watchdog.
- dev_hard_start_xmit() does not check txq everywhere which will lead a crash
when tso is disabled for lower device.
Fix this by explicitly introducing a new param for .ndo_select_queue() for just
selecting queues in the case of l2 forwarding offload. netdev_pick_tx() was also
extended to accept this parameter and dev_queue_xmit_accel() was used to do l2
forwarding transmission.
With this fixes, NETIF_F_LLTX could be preserved for macvlan and there's no need
to check txq against NULL in dev_hard_start_xmit(). Also there's no need to keep
a dedicated ndo_dfwd_start_xmit() and we can just reuse the code of
dev_queue_xmit() to do the transmission.
In the future, it was also required for macvtap l2 forwarding support since it
provides a necessary synchronization method.
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: e1000-devel@lists.sourceforge.net
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 837052d0ccc5a789a578f8b628ba154b63bd51ea |
|
23-Dec-2013 |
Or Gerlitz <ogerlitz@mellanox.com> |
net/mlx4_en: Add netdev support for TCP/IP offloads of vxlan tunneling
When the device tunneling offloads mode is vxlan do the following
- call SET_PORT with the relevant setting
- add DMFS steering vxlan rule for the device self and multicast mac addresses
of the form: {<ETH, outer-mac> <VXLAN, ANY vnid> <ETH, ANY mac>} --> RSS QP
- set relevant QPC fields in RSS context and RX ring QPs
- in TX flow, set WQE fields to generate HW checksum, and handle gso skbs
which are marked for encapsulation such that the HW will segment them properly.
- in RX flow, read HW offloaded checksum for encapsulated packets from the CQE
- advertize hw_enc_features and NETIF_F_GSO_UDP_TUNNEL to the networking stack
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 0276a330617a0cf380f09e5065299078d3d45886 |
|
19-Dec-2013 |
Eugenia Emantayev <eugenia@mellanox.com> |
net/mlx4_en: Add NAPI support for transmit side
Add NAPI for TX side,
implement its support and provide NAPI callback.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| d03a68f8217ea03492e4f7928db222dc6544792a |
|
19-Dec-2013 |
Ido Shamay <idos@mellanox.com> |
net/mlx4_en: Configure the XPS queue mapping on driver load
Only TX rings of User Piority 0 are mapped.
TX rings of other UP's are using UP 0 mapping.
XPS is not in use when num_tc is set.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 163561a4e2f8af44e96453bc10c7a4f9bcc736e1 |
|
06-Nov-2013 |
Eugenia Emantayev <eugenia@mellanox.com> |
net/mlx4_en: Datapath structures are allocated per NUMA node
For each RX/TX ring and its CQ, allocation is done on a NUMA node that
corresponds to the core that the data structure should operate on.
The assumption is that the core number is reflected by the ring index.
The affected allocations are the ring/CQ data structures,
the TX/RX info and the shared HW/SW buffer.
For TX rings, each core has rings of all UPs.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 41d942d56cfd21058fba465804e14ba349541442 |
|
06-Nov-2013 |
Eugenia Emantayev <eugenia@mellanox.com> |
net/mlx4_en: Datapath resources allocated dynamically
Currently all TX/RX rings and completion queues are part of the
netdev priv structure and are allocated statically. This patch
will change the priv to hold only arrays of pointers and therefore
all TX/RX rings and completetion queues will be allocated
dynamically. This is in preparation for NUMA aware allocations.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 5f1cd200c4e4e1a6bce946aaac40c7a10427f3ed |
|
21-Aug-2013 |
Amir Vadai <amirv@mellanox.com> |
net/mlx4_en: Reduce scope of local variables in mlx4_en_xmit
Some variables could have their scope reduced.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 237a3a3b1544574ead3dc459063424de8c0319e0 |
|
21-Aug-2013 |
Amir Vadai <amirv@mellanox.com> |
net/mlx4_en: Fix handling of dma_map failure
Result of skb_frag_dma_map() and dma_map_single() wasn't checked.
Added a check and proper handling in case of failure.
Moved the mapping to the beginning of mlx4_en_xmit(), before updating
the ring data structure to make error handling easier.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| bd2f631d7c60502e24e801a3eea1806868951bcc |
|
21-Aug-2013 |
Amir Vadai <amirv@mellanox.com> |
net/mlx4_en: Notify user when TX ring in error state
When hardware gets into error state, must notify user about it.
When QP in error state no traffic will be tx'ed from the attached
tx_ring.
Driver should know how to recover from this unexpected state. I will send later
on the recovery flow, but having the print shouldn't be delayed.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 2d4b646613d6b12175b017aca18113945af1faf3 |
|
25-Jul-2013 |
Eugenia Emantayev <eugenia@mellanox.com> |
net/mlx4_en: Fix BlueFlame race
Fix a race between BlueFlame flow and stamping in post send flow.
Example:
SW: Build WQE 0 on the TX buffer, except the ownership bit
SW: Set ownership for WQE 0 on the TX buffer
SW: Ring doorbell for WQE 0
SW: Build WQE 1 on the TX buffer, except the ownership bit
SW: Set ownership for WQE 1 on the TX buffer
HW: Read WQE 0 and then WQE 1, before doorbell was rung/BF was done for WQE 1
HW: Produce CQEs for WQE 0 and WQE 1
SW: Process the CQEs, and stamp WQE 0 and WQE 1 accordingly (on the TX buffer)
SW: Copy WQE 1 from the TX buffer to the BF register - ALREADY STAMPED!
HW: CQE error with index 0xFFFF - the BF WQE's control segment is STAMPED,
so the BF index is 0xFFFF. Error: Invalid Opcode.
As a result QP enters the error state and no traffic can be sent.
Solution:
When stamping - do not stamp last completed wqe.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| c08355fb61fb064d141b8bd156145d326f33022f |
|
03-Jun-2013 |
govindarajulu.v <govindarajulu90@gmail.com> |
mlx4: use __netdev_pick_tx instead of __skb_tx_hash in mlx4_en_select_queue
mlx4_en_select_queue() uses __skb_tx_hash to select the transmit queue.
XPS settings are ignored by this. Instead, we can use __netdev_pick_tx
to select the transmit queue.
Compile test only.
Signed-off-by: govindarajulu.v <govindarajulu90@gmail.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| eb0cabbd1bebbf41858ded768c9cad8840708447 |
|
23-Apr-2013 |
Amir Vadai <amirv@mellanox.com> |
net/mlx4_en: Support software timestamping
Kernel software timestamping requires that the driver calls skb_tx_timestamp
just before passing the skb to the HW MAC layer. This patch adds this call.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| ec693d47010e8302e61e0bdf3f47496c5610641a |
|
23-Apr-2013 |
Amir Vadai <amirv@mellanox.com> |
net/mlx4_en: Add HW timestamping (TS) support
The patch allows to enable/disable HW timestamping for incoming and/or
outgoing packets. It adds and initializes all structs and callbacks
needed by kernel TS API.
To enable/disable HW timestamping appropriate ioctl should be used.
Currently HWTSTAMP_FILTER_ALL/NONE and HWTSAMP_TX_ON/OFF only are
supported.
When enabling TS on receive flow - VLAN stripping will be disabled.
Also were made all relevant changes in RX/TX flows to consider TS request
and plant HW timestamps into relevant structures.
mlx4_ib was fixed to compile with new mlx4_cq_alloc() signature.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 41b749201bbe54ce807c4287b4942e85cb0ca466 |
|
06-Feb-2013 |
Tom Herbert <therbert@google.com> |
mlx4_en: Fix BQL reset TX queue call point
Fix issue in Mellanox driver related to BQL. netdev_tx_reset_queue
was not being called in certain situations where the device was
being start and stopped. Moved netdev_tx_reset_queue from the reset
device path to mlx4_en_free_tx_buf which is where the rings are
cleaned in a reset (specifically from device being stopped).
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 79aeaccd915c527a75f2cb01682eab160bed4f48 |
|
07-Feb-2013 |
Yan Burman <yanb@mellanox.com> |
net/mlx4_en: Optimize loopback related checks in data path
Currently there are relatively complex conditional checks in the fast path,
for TX loopback enabling and resulting RX filter logic.
Move elaborate if's out of data path, replace them with a single flag
for each state and update that state from appropriate places.
Also, in native (non SRIOV) mode and not in loopback or in selftest,
there is no need to try and filter out packets that HW loopback-ed,
as in native mode we do not loopback packets anymore.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 7225922558f04f25a22683ce08454dae8dd4b9f4 |
|
24-Jan-2013 |
Amir Vadai <amirv@mellanox.com> |
net/mlx4_en: Fix a race when closing TX queue
There is a possible race where the TX completion handler can clean the
entire TX queue between the decision that the queue is full and actually
closing it. To avoid this situation, check again if the queue is really
full, if not, reopen the transmit and continue with sending the packet.
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 546bfedbe604baeb5a03736593bb95c9aa56bcfa |
|
17-Jan-2013 |
Eric Dumazet <edumazet@google.com> |
net/mlx4_en: remove redundant code
remove redundant code from build_inline_wqe()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 213815a1e6ae70b9648483b110bc5081795f99e8 |
|
17-Jan-2013 |
Yan Burman <yanb@mellanox.com> |
net/mlx4_en: Fix bridged vSwitch configuration for non SRIOV mode
Commit 5b4c4d36860e "mlx4_en: Allow communication between functions on
same host" introduced a regression under which a bridge acting as vSwitch
whose uplink is an mlx4 Ethernet device become non-operative in native
(non sriov) mode. This happens since broadcast ARP requests sent by VMs
were loopback-ed by the HW and hence the bridge learned VM source MACs
on both the VM and the uplink ports.
The fix is to place the DMAC in the send WQE only under SRIOV/eSwitch
configuration or when the device is in selftest.
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| d317966bd3249ee7cd912931ab013c49cb77b9a4 |
|
02-Dec-2012 |
Amir Vadai <amirv@mellanox.com> |
net/mlx4_en: Set number of rx/tx channels using ethtool
Add support to changing number of rx/tx channels using
ethtool ('ethtool -[lL]'). Where the number of tx channels specified in ethtool
is the number of rings per user priority - not total number of tx rings.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 08ff32352d6ff7083533dc1c25618d42f92ec28e |
|
21-Oct-2012 |
Or Gerlitz <ogerlitz@mellanox.com> |
mlx4: 64-byte CQE/EQE support
ConnectX-3 devices can use either 64- or 32-byte completion queue
entries (CQEs) and event queue entries (EQEs). Using 64-byte
EQEs/CQEs performs better because each entry is aligned to a complete
cacheline. This patch queries the HCA's capabilities, and if it
supports 64-byte CQEs and EQES the driver will configure the HW to
work in 64-byte mode.
The 32-byte vs 64-byte mode is global per HCA and not per CQ or EQ.
Since this mode is global, userspace (libmlx4) must be updated to work
with the configured CQE size, and guests using SR-IOV virtual
functions need to know both EQE and CQE size.
In case one of the 64-byte CQE/EQE capabilities is activated, the
patch makes sure that older guest drivers that use the QUERY_DEV_FUNC
command (e.g as done in mlx4_core of Linux 3.3..3.6) will notice that
they need an update to be able to work with the PPF. This is done by
changing the returned pf_context_behaviour not to be zero any more. In
case none of these capabilities is activated that value remains zero
and older guest drivers can run OK.
The SRIOV related flow is as follows
1. the PPF does the detection of the new capabilities using
QUERY_DEV_CAP command.
2. the PPF activates the new capabilities using INIT_HCA.
3. the VF detects if the PPF activated the capabilities using
QUERY_HCA, and if this is the case activates them for itself too.
Note that the VF detects that it must be aware to the new PF behaviour
using QUERY_FUNC_CAP. Steps 1 and 2 apply also for native mode.
User space notification is done through a new field introduced in
struct mlx4_ib_ucontext which holds device capabilities for which user
space must take action. This changes the binary interface so the ABI
towards libmlx4 exposed through uverbs is bumped from 3 to 4 but only
when **needed** i.e. only when the driver does use 64-byte CQEs or
future device capabilities which must be in sync by user space. This
practice allows to work with unmodified libmlx4 on older devices (e.g
A0, B0) which don't support 64-byte CQEs.
In order to keep existing systems functional when they update to a
newer kernel that contains these changes in VF and userspace ABI, a
module parameter enable_64b_cqe_eqe must be set to enable 64-byte
mode; the default is currently false.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
| 2b39a06198a0fbaf44a69f435c5d2b4280a0c10e |
|
25-Oct-2012 |
Moni Shoua <monis@mellanox.co.il> |
net/mlx4_en: Don't use vlan tag value as an indication for vlan presence
The vlan tag can be zero. This is why it can't serve as an indication
that packet requires VLAN header in the TX flow.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 7208ca300725ebc1dd4c60511ed67a69c684eb91 |
|
25-Oct-2012 |
Jack Morgenstein <jackm@dev.mellanox.co.il> |
net/mlx4_en: Fix double-release-range in tx-rings
The QP range is reserved as a single block. However, when freeing the
en resources, the tx-ring QPs are released both in mlx4_en_destroy_tx_ring
(one at a time) and in mlx4_en_free_resources (as a block release).
Fix by eliminating the one-at-a-time release in mlx4_en_destroy_tx_ring.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 8112ec3b8722680251aecdcc23dfd81aa7af6340 |
|
28-Sep-2012 |
Eric Dumazet <edumazet@google.com> |
mlx4: dont orphan skbs in mlx4_en_xmit()
After commit e22979d96a55d (mlx4_en: Moving to Interrupts for TX
completions) we no longer need to orphan skbs in mlx4_en_xmit()
since skb wont stay a long time in TX ring before their release.
Orphaning skbs in ndo_start_xmit() should be avoided as much as
possible, since it breaks TCP Small Queue or other flow control
mechanisms (per socket limits)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| c18520bd1b244fe8e3ac5358137321780a70d6e7 |
|
03-Aug-2012 |
Yevgeny Petrilin <yevgenyp@mellanox.co.il> |
net/mlx4_en: Fixing TX queue stop/wake flow
Removing the ring->blocked flag, it is redundant and leads to a race:
We close the TX queue and then set the "blocked" flag.
Between those 2 operations the completion function can check the "blocked"
flag, sees that it is 0, and wouldn't open the TX queue.
Using netif_tx_queue_stopped to check the state of the queue to avoid this race.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| bc6a4744b827c5a78ca591acca81809bddb8b2db |
|
17-May-2012 |
Amir Vadai <amirv@mellanox.com> |
net/mlx4_en: num cores tx rings for every UP
Change the TX ring scheme such that the number of rings for untagged packets
and for tagged packets (per each of the vlan priorities) is the same, unlike
the current situation where for tagged traffic there's one ring per priority
and for untagged rings as the number of core.
Queue selection is done as follows:
If the mqprio qdisc is operates on the interface, such that the core networking
code invoked the device setup_tc ndo callback, a mapping of skb->priority =>
queue set is forced - for both, tagged and untagged traffic.
Else, the egress map skb->priority => User priority is used for tagged traffic, and
all untagged traffic is sent through tx rings of UP 0.
The patch follows the convergence of discussing that issue with John Fastabend
over this thread http://comments.gmane.org/gmane.linux.network/229877
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Liran Liss <liranl@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 5b263f5374ea70daa61ed9f5cc5d8f4ac236efbd |
|
23-Apr-2012 |
Yevgeny Petrilin <yevgenyp@mellanox.co.il> |
mlx4_en: Byte Queue Limit support
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| e22979d96a55d24bc43247341a052ec1b3a7fda6 |
|
23-Apr-2012 |
Yevgeny Petrilin <yevgenyp@mellanox.co.il> |
mlx4_en: Moving to Interrupts for TX completions
Moving to interrupts instead of polling fpr TX completions
Avoiding situations where skb can be held in by the driver for
a long time (till timer expires).
The change is also necessary for supporting BQL.
Removing comp_lock that was required because we could handle TX
completions from several contexts: Interrupts, timer, polling.
Now there is only interrupts
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 897d7846b483da58d0b46bf806cf362a71501c56 |
|
04-Apr-2012 |
Amir Vadai <amirv@mellanox.com> |
net/mlx4_en: sk_prio <=> UP for untagged traffic
Since vlan egress map is only good for tagged traffic, need to have other
mapping to be used by untagged traffic.
For that, the driver uses sch_mqprio mapping. This mapping could be set by
using tc tool from iproute2 package.
Mapped UP will be used by the HW for QoS purposes, but won't go out on the
wire.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 0e98b523c4a4119cbd17e58dff385cc329064694 |
|
04-Apr-2012 |
Amir Vadai <amirv@mellanox.com> |
net/mlx4_en: Force user priority by QP attribute
Instead of relying on HW to change schedule queue by UP, schedule
queue is fixed for a tx_ring, and UP in WQE is ignored in this aspect. This
resolves two issues with untagged traffic:
1. untagged traffic has no UP in packet which is needed for QoS. The change
above allows setting the schedule queue (and by that the UP) of such a stream.
2. BlueFlame uses the same field used by vlan tag. So forcing UP from QPC
allows using BF for untagged but prioritized traffic.
In old firmware that force UP is not supported, untagged traffic will not subject to
QoS.
Because UP is set by QP, need to always have a tx ring per UP, even if pfcrx
module paramter is false.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 966684d581c9c04202e6612a792e36ae7bc5fd59 |
|
06-Mar-2012 |
Or Gerlitz <ogerlitz@mellanox.com> |
net/mlx4: fix sparse warnings on TX blue flame buffer
The blue flame buffer is defined to be of type void __iomem *
but was passed to mlx4_bf_copy which gets unsigned long * .
This triggered sparse warning on different address spaces,
fix that by changing mlx4_bf_copy first param to be of type void __iomem * .
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| ebf8c9aa032f03343b91c91951b0705021b02eb0 |
|
06-Mar-2012 |
Yevgeny Petrilin <yevgenyp@mellanox.co.il> |
net/mlx4_en: Saving mem access on data path
Localized the pdev->dev, and using dma_map instead of pci_map
There are multiple map/unmap operations on data path,
optimizing those by saving redundant pointer access.
Those places were identified as hot-spots when running kernel profiling
during some benchmarks.
The fixes had most impact when testing packet rate with small packets,
reducing several % from CPU load, and in some case being the difference
between reaching wire speed or being CPU bound.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 18f973af3e7028620186d1c1ace044506bb6229e |
|
05-Mar-2012 |
Eric Dumazet <eric.dumazet@gmail.com> |
mlx4_en: remove sparse errors
Fix new sparse errors introduced in commit 6221217199 (mlx4_en: dont
change mac_header on xmit)
Reported-by: Or Gerlitz <or.gerlitz@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 622121719934f60378279eb440d3cec2fc3176d2 |
|
25-Feb-2012 |
Eric Dumazet <eric.dumazet@gmail.com> |
mlx4_en: dont change mac_header on xmit
A driver xmit function is not allowed to change skb without special
care.
mlx4_en_xmit() should not call skb_reset_mac_header() and instead should
use skb->data to access ethernet header.
This removes a dumb test : if (ethh && ethh->h_dest)
Also remove this slow mlx4_en_mac_to_u64() call, we can use
get_unaligned() to get faster code.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| e404decb0fb017be80552adee894b35307b6c7b4 |
|
29-Jan-2012 |
Joe Perches <joe@perches.com> |
drivers/net: Remove unnecessary k.alloc/v.alloc OOM messages
alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.
Remove the allocation failure messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 5b4c4d36860ef1c411d0669ffc15090417a33389 |
|
13-Dec-2011 |
Eugenia Emantayev <eugenia@mellanox.co.il> |
mlx4_en: Allow communication between functions on same host
To enable internal loopback, always fill DMAC in control segment
when transmitting the packet, once this is done, the packet is subject
for loopback for if the DMAC mathces one of the multicast/unicast addresses
registered on the physical port.
In receive path if source MAC is our own MAC and we are not in selftest,
or not in force LB mode - drop this packet.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| c140d769c2b6d87148203a78aa0d72595a19b2de |
|
26-Nov-2011 |
Amir Vadai <amirv@mellanox.co.il> |
net/mlx4_en: bug fix for the case of vlan id 0 and UP 0
When using vlan 0 and UP 0, vlan header wasn't placed.
Signed-off-by: Amir Vadai <amirv@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 60d6fe99e4a507f77b63c090eb8aacb67e21687a |
|
26-Nov-2011 |
Amir Vadai <amirv@mellanox.co.il> |
net/mlx4_en: adding loopback support
Device must be in promiscuous mode or DMAC must be same as the host MAC, or
else packet will be dropped by the HW rx filtering.
Signed-off-by: Amir Vadai <amirv@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| f0ab34f011d805ce5b1a341409c9c26f0fc8252b |
|
26-Nov-2011 |
Yevgeny Petrilin <yevgenyp@mellanox.co.il> |
net/mlx4_en: using non collapsed CQ on TX
Moving to regular Completion Queue implementation (not collapsed)
Completion for each transmitted packet is written to new entry.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 6eb07caf1ac5723720caea2ee93cd11b7058a0aa |
|
16-Sep-2011 |
Paul Gortmaker <paul.gortmaker@windriver.com> |
drivers/net: Add moduleparam.h to drivers as required.
These files were using moduleparam infrastructure, but were not
including anything for it -- which is fine when module.h is being
implicitly included in all files, but that is going away.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
| 311761c8a553adaa3ad7482b1fdde1ce9042d3e2 |
|
20-Oct-2011 |
Ian Campbell <Ian.Campbell@citrix.com> |
mlx4: convert to SKB paged frag API.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| ad04378cecca9c33b5ea3e46aa4ed71b15e0be0c |
|
18-Oct-2011 |
Yevgeny Petrilin <yevgenyp@mellanox.co.il> |
mlx4_en: Checksum counters per ring
Not updating common counters from data path.
The checksum counters are per ring, summarizing them when collecting statistics.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 9e903e085262ffbf1fc44a17ac06058aca03524a |
|
18-Oct-2011 |
Eric Dumazet <eric.dumazet@gmail.com> |
net: add skb frag size accessors
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 5a2cc190eb3fe58fe519795c509b01b25795992e |
|
13-May-2011 |
Jeff Kirsher <jeffrey.t.kirsher@intel.com> |
mlx4: Move the Mellanox driver
Moves the Mellanox driver into drivers/net/ethernet/mellanox/ and
make the necessary Kconfig and Makefile changes.
CC: Roland Dreier <roland@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|