| aac307f9dd5ce1fe651140a036ab4b0a0571b54a |
|
26-Aug-2014 |
H Hartley Sweeten <hsweeten@visionengravers.com> |
staging: comedi: comedi_pci: introduce comedi_pci_detach()
Introduce a generic (*detach) function for comedi PCI drivers to handle
the boilerplate code needed to detach a PCI driver.
This function works similar to comedi_legacy_detach() where it will:
* free the dev->irq if it has been requested
* iounmap the dev->mmio addres if it has been ioremap'ed
The helper then calls comedi_pci_disable() to release the regions and
disable the PCI device.
Use the new helper directly for the (*detach) in the following cases:
* where comedi_pci_disable() is used directly for the (*detach)
* where the detach function is just boilerplate
Use the new helper in the (*detach) of the simpler PCI drivers. Call
the helper after disabling interrupts (reset) and before any additional
cleanup (kfree) to avoid any race conditions with the interrupt handler.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| dbd446fc7aab519c213e63eefa15c82586a50989 |
|
10-Feb-2014 |
H Hartley Sweeten <hsweeten@visionengravers.com> |
staging: comedi: don't clear 'data' on (*insn_read) timeout
It's not necessary to clear the returned data pointer when an (*insn_read)
times out. For aesthetics, remove all of these in the drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 22ca19d93d92c79cff68270846a84bd34fe6fb34 |
|
10-Feb-2014 |
H Hartley Sweeten <hsweeten@visionengravers.com> |
staging: comedi: move (*insn_{read, write}) timeout debug messages to core
Have the comedi core display a standard dev_dbg() message when a timeout
occurs and remove all the driver specific messages.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 443e6d02c8f5541f8f81b5f2b54cf5277ee5fadb |
|
10-Feb-2014 |
H Hartley Sweeten <hsweeten@visionengravers.com> |
staging: comedi: dyna_pci10xx: use comedi_timeout()
Use comedi_timeout() to wait for the analog input end-of-conversion.
Also, remove some unnecessary comments.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| c93999c21319439c4fe2da85f2ec40ed477379ac |
|
03-Feb-2014 |
H Hartley Sweeten <hsweeten@visionengravers.com> |
staging: comedi: drivers: remove final 'attach' messages
These messages are just added noise. Remove them.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| eff3689b0f6cf6c92c1ae61c8c821c149eeac4ec |
|
10-Dec-2013 |
H Hartley Sweeten <hsweeten@visionengravers.com> |
staging: comedi: dyna_pci10xx: tidy up comedi_lrange tables
Tidy up the whitespace in the comedi_lrange tables.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 41e043fcfa2236bb2c4a8335eb09f4c8cee224b3 |
|
03-Dec-2013 |
Jingoo Han <jg1.han@samsung.com> |
staging: remove DEFINE_PCI_DEVICE_TABLE macro
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 4ced969ac63118fa4efdc367aef08215488f1eb0 |
|
26-Nov-2013 |
H Hartley Sweeten <hsweeten@visionengravers.com> |
staging: comedi: dyna_pci10xx: convert a KERN_DEBUG message to dev_dbg()
Convert a printk(KERN_DEBUG ... message to dev_dbg().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 97f4289ad08cffe55de06d4ac4f89ac540450aee |
|
30-Aug-2013 |
H Hartley Sweeten <hsweeten@visionengravers.com> |
staging: comedi: drivers: use comedi_dio_update_state() for simple cases
Use comedi_dio_update_state() to handle the boilerplate code to update
the subdevice s->state for simple cases where the hardware is updated
when any channel is modified.
Also, fix a bug in the amplc_pc263 and amplc_pci263 drivers where the
current state is not returned in data[1].
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| ce157f8032bbd46d9427034c335b0afd751da25d |
|
25-Jun-2013 |
H Hartley Sweeten <hsweeten@visionengravers.com> |
staging: comedi: don't rely on comedidev.h to include headers
comedidev.h is the main kernel header for comedi. Every comedi
driver includes this header which then includes a number of
<linux/*> headers. All the drivers need <linux/module.h> and some
of them need <linux/delay.h>. The rest are not needed by any of
the drivers.
Remove all the includes in comedidev.h except for <linux/dma-mapping.h>,
which is needed to pick up the enum dma_data_direction for the
comedi_subdevice definition, and "comedi.h", which is the uapi
header for comedi.
Add <linux/module.h> to all the comedi drivers and <linux/delay.h>
to the couple that need it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 0bdab509bf9c6d838dc0a3b1d68bbf841fc20b5a |
|
25-Jun-2013 |
H Hartley Sweeten <hsweeten@visionengravers.com> |
staging: comedi: use comedi_alloc_devpriv()
Use the helper function to allocate memory and set the comedi_device
private data pointer.
This removes the dependency on slab.h from most of the drivers so
remove the global #include in comedidev.h and the local #include
in some of the drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 641f064e5df6fb3aaeb6256031a153a5efb16ca6 |
|
25-Apr-2013 |
H Hartley Sweeten <hsweeten@visionengravers.com> |
staging: comedi: remove FSF address from boilerplate text
Addresses change...
Remove the paragraph with the FSF address from all the comedi source
files.
Also, remove the paragraph about the finding the complete GPL in the
COPYING file since it's unnecessary.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 5993f3a2692eed3c74c86882155b8703a0060ad5 |
|
08-Apr-2013 |
H Hartley Sweeten <hsweeten@visionengravers.com> |
staging: comedi: remove unnecessary dev->board_name initialization
The dev->board_name is now initialized by the comedi core before calling
the(*attach) or (*auto_attach) function in a driver. As long as the driver
does no additional probing, it's no longer necessary initialize the board_name.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 818f569fe930c5b8a05d1a44ece3c63c99c13c88 |
|
13-Mar-2013 |
H Hartley Sweeten <hsweeten@visionengravers.com> |
staging: comedi_pci: pass comedi_device to comedi_pci_enable()
Make comedi_pci_enable() use the same parameter type as
comedi_pci_disable(). This also allows comedi_pci_enable
to automatically determine the resource name passed to
pci_request_regions().
Make sure the errno value returned is passed on instead of
assuming an errno. Also, remove any kernel noise that is
generated when the call fails.
The National Instruments drivers that use the mite module
currently enable the PCI device in the mite module. For
those drivers move the call to comedi_pci_enable into the
driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 7f072f54ae5dc9965cbe450419b1389d13e2b849 |
|
13-Mar-2013 |
H Hartley Sweeten <hsweeten@visionengravers.com> |
staging: comedi_pci: make comedi_pci_disable() safe to call
Currently all the comedi PCI drivers need to do some checking in
their (*detach) before calling comedi_pci_disable() in order to
make sure the PCI device has actually be enabled.
Change the parameter passed to comedi_pci_disable() from a struct
pci_dev pointer to a comedi_device pointer and have comedi_pci_disable()
handle all the checking.
For most comedi PCI drivers this also allows removing the local
variable holding the pointer to the pci_dev. For some of the drivers
comedi_pci_disable can now be used directly as the (*detach) function.
The National Instruments drivers that use the mite module currently
enable/disable the PCI device in the mite module. For those drivers
move the call to comedi_pci_disable into the driver and make sure
dev->iobase is set to a non-zero value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| b8f4ac237e382accd4b30c75043939f7ed9e79a6 |
|
05-Mar-2013 |
H Hartley Sweeten <hsweeten@visionengravers.com> |
staging: comedi: comedi_pci: change the comedi_pci_auto_config() 'context'
The comedi_pci_auto_config() function is used to allow the PCI driver
(*probe) function to automatically call the comedi driver (*auto_attach).
This allows the comedi driver to be part of the PnP process when the
PCI device is detected.
Currently the comedi_pci_auto_config() always passes a 'context' of '0'
to comedi_auto_config(). This makes the 'context' a bit useless.
Modify comedi_pci_auto_config() to allow the comedi pci drivers to pass
a 'context' from the PCI driver.
Make all the comedi pci drivers pass the pci_device_id 'driver_data' as
the 'context'. Since none of the comedi pci drivers currently set the
'driver_data' the 'context' will still be '0'.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 33782dd5edf8db3cdb7c81a3523bf743dd0209b7 |
|
30-Jan-2013 |
H Hartley Sweeten <hsweeten@visionengravers.com> |
staging: comedi: conditionally build in PCI driver support
Separate the comedi_pci_* functions out of drivers.c into a new
source file, comedi_pci.c. This allows conditionally building
support for comedi PCI drivers into the comedi core. Fix the
Kconfig and Makefile appropriately.
Group all the comedi_pci_* prototypes and related defines into one
place in comedidev.h. Protect these prototypes with an #ifdef and
provide some dummy functions so that the mixed ISA/PCI comedi
drivers will still build correctly.
Remove the #include <linux/pci.h> from comedidev.h and drivers.c. This
include is only needed by the comedi PCI driver support code and the
PCI drivers. The include should occur in those files.
Also, remove the #include <linux/pci.h> from a couple non-PCI drivers
since it's not needed.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 9901a4d75d007686e8f6473189cafc4b216b7449 |
|
22-Jan-2013 |
Peter Huewe <peterhuewe@gmx.de> |
staging/comedi: Use comedi_pci_auto_unconfig directly for pci_driver.remove
(Almost) all comedi pci drivers have some wrapper for their
pci_driver.remove function which simply calls comedi_pci_auto_unconfig
which has the same function prototype as the wrapper.
-> we can remove these wrappers and call comedi_pci_auto_unconfig
directly. This removes a lot some boilerplate code and saves some bytes.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 53b800198592b0ff96577ecc5f116f7d902a4362 |
|
19-Nov-2012 |
Bill Pemberton <wfp5p@virginia.edu> |
staging: comedi: remove use of __devexit
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| a690b7e535f2f97a3a05ee570715abeb60a8910f |
|
19-Nov-2012 |
Bill Pemberton <wfp5p@virginia.edu> |
staging: comedi: remove use of __devinit
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| a471eace7baa40cdf16d3f26b2f78ddce613ca8f |
|
19-Nov-2012 |
Bill Pemberton <wfp5p@virginia.edu> |
staging: comedi: remove use of __devexit_p
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 750af5e568d060ec6994cdcb4e86cdddfcd473c0 |
|
30-Oct-2012 |
Ian Abbott <abbotti@mev.co.uk> |
staging: comedi/drivers: use auto_attach instead of attach_pci
Change comedi drivers for PCI boards to use the new `auto_attach()`
method instead of the `attach_pci()` method. I plan to remove the
`attach_pci()` and `attach_usb()` methods from `struct comedi_driver`
once nothing is using them.
Tag the functions with `__devinit` where they are not already so tagged,
as they are only called during PCI probe.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 00f5c774a0f551e297c343222d17a3f919c603d3 |
|
25-Oct-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: dyna_pci10xx: remove PCI_VENDOR_ID_DYNALOG
The PCI chip used on this board is from PLX Technologies Inc. As stated
in the comments of this driver, Dynalog does not have a registered PCI
vendor id so this board uses the PLX vendor id. The kernel provides an
id for that vendor in pci_ids.h (PCI_VENDOR_ID_PLX). Use it instead of
creating a duplicate with a different name.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 7fc465b106b40a598d83a0c98d0e8c2a1b4653ff |
|
23-Oct-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: auto-config drivers do not need to set hw_dev
The comedi core now sets the 'hw_dev' pointer in the function
comedi_auto_config_helper() before calling the auto attach
function in the driver.
Remove the now unnecessary call to comedi_set_hw_dev() in the
drivers that use the auto-config attach mechanism.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| c34fa261b0ac3a862ccd3f71ee55a16b920dfc83 |
|
23-Oct-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: remove inline alloc_private()
This inline function has a very generic name and it's only a
wrapper around a simple kzalloc(). Since the inline function
does not save any lines-of-code, instead of renaming it just
remove it and do the kzalloc() directly.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 1b39406b3ec9fb58e5577e7266562dd9a7816949 |
|
06-Sep-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: dyna_pci10xx: remove subdevice pointer math
Convert the comedi_subdevice access from pointer math to array
access.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| c3b52d465916acd02803e83e58d9440ec365ab72 |
|
17-Aug-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: dyna_pci10xx: remove manual legacy attach
This driver uses the 'attach_pci' callback to attach the pci device
to the comedi subsystem. Since the 'attach' callback is now optional
it can be removed from the driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 3131de834e8ff8f6f1581d838a51cf30e8d22b61 |
|
15-Aug-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: dnya_pci10xx: remove unused DRV_NAME
This define is not used in the driver. Remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| a38936fe819a59c88957ef4bda6a33c0a537938a |
|
15-Aug-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: dnya_pci10xx: remove unneeded boardinfo code
The boardinfo code is not needed by this driver. Only one board
type is supported.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 8fda437d8924d2f9c864d805862b43ff36020c5b |
|
15-Aug-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: dnya_pci10xx: move boardinfo values into subdevice setup
There is only one "boardtype" actually supported by this driver.
The second entry in the boardinfo is a dummy entry that would
result in an unusable device.
Remove the boardinfo fields and just use the open coded values
in the subdevice setup.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 4884f724c3f78eac7ea814fbd71545b45577a1be |
|
15-Aug-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: dnya_pci10xx: remove unused fields in the boardinfo
The *_bits information in the boardinfo is not used by the driver.
Remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| f2eacff1369c46c7c4dab595a460dd9ec40e51db |
|
15-Aug-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: dnya_pci10xx: cleanup the analog output range
The analog output channels on this board only support a single
range, 0-10V unipolar. This range is available as an exported
symbol from the comedi core and "range_unipolar10". Use that
instead of duplicating the range in this driver and remove
the information from the boardinfo.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 690e839fc4915a372f2338b148c36d8949822253 |
|
15-Aug-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: dnya_pci10xx: use attach_pci callback
Convert this PCI driver to use the comedi PCI auto config attach
mechanism by adding an attach_pci callback function. Since the
driver does not require any external configuration options, disable
the legacy attach by making the attach simply return -ENOSYS. This
removes the need to walk the pci bus to find the pci_dev and the
need for the pci_dev_put() in the detach.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| af0677c14e990e64bd6571be691e0bebd82a5dc0 |
|
15-Aug-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: dnya_pci10xx: remove thisboard and devpriv macros
These macros rely on local variables having a specific name. Replace
them with local variables where used. Use the comedi_board() helper
to get the thisboard pointer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| f2a64902e3c2ffa34b52e6ad13e8e3c40f6919c7 |
|
19-Jul-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: dyna_pci10xx: fix detach
The detach for this driver is missing the check to make sure
that the pci device is enabled before disabling it.
It's also missing the pci_dev_put().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 06183026d82cf58cdfba53b661914faf3c414029 |
|
19-Jul-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: dyna_pci10xx: store the pci_dev in the comedi_device
Use the hw_dev pointer in the comedi_device struct to hold the
pci_dev instead of carrying it in the private data.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| b694c4f4339bf4126e944def8318ff4f5cfbee76 |
|
19-Jul-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: dyna_pci10xx: use dev->iobase
Use dev->iobase to hold one of the pci base addresses used
by the driver instead of carrying it in the private data.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 87790601cc603ea657fa667dd329fb21f318dfa9 |
|
19-Jul-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: dyna_pci10xx: remove unused bars from the private data
All of the pci device base address registers are saved in the private
data but only bar2 and bar3 are used by the driver. Remove the others.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 423e0e3f551212df86d4e06287d253c2ae26e8dd |
|
19-Jul-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: dyna_pci10xx: remove 'valid' from the private data
This variable is set at the end of the attach but never used
in the driver. Remove it.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 6bdae560f46cddc8aeff5bd9c76454168ee8e8ab |
|
19-Jul-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: dyna_pci10xx: remove the 'start_stop_sem' mutex
The comedi core already has a mutex protecting the attach/detach
of the comedi drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 5d30e51909b61916744e45d3c50cf42569c92c20 |
|
19-Jul-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: dyna_pci10xx: cleanup "find pci device" code
Cleanup the "find pci device" code so that it follows the style
of the other comedi pci drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 1f20b973f68346af2712e5d014932d984b6f5387 |
|
19-Jul-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: dyna_pci10xx: factor out the "find pci device" code
Factor the "find pci device" code out of the attach function.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| a2714e3e42e746d6c8525c35fdcc58fb60c2830d |
|
18-Jun-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: fix return value for insn_bits functions
The comedi_subdevice 'insn_bits' functions return the number of data
elements used to perform the command. Most of the insn_bits functions
return an open coded '2' to indicate this. The same value is available
as 'insn->n'. Return that instead to better indicate what the return
means.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 520706607befd1f5c20ec14db35d6be45791bc41 |
|
18-Jun-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: remove unneeded sanity check in insn_bits functions
The comedi core does the sanity check to make sure that the data length
the INSN_BITS instruction is 2. There is no need for the drivers to do
this check. Remove all the sanity checks in the drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 8b6c56949ffa83dbc2a6e8fa3f98b10a19372207 |
|
12-Jun-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: propogate error code from comedi_alloc_subdevices
comedi_alloc_subdevices can fail with -EINVAL or -ENOMEM. When it
does fail make sure to pass the proper error code back.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbott@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 0e4039f3112326d73f66b00fd18468a3804ed29e |
|
12-Jun-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: remove the comed_alloc_subdevices "allocation failed" messages
Remove all the "allocation failed" debug messages that are displayed
when the comedi_alloc_subdevices call fails.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbot <abbott@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 2f0b9d082e5d0056a3aca4be038483a564849196 |
|
12-Jun-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: export alloc_subdevices as comedi_alloc_subdevices
Move the inline alloc_subdevices() function from comedidev.h
to drivers.c and rename it to comedi_alloc_subdevices(). The
function is large enough to warrant being an exported symbol
rather than being an inline in every driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| bc04bec0e0c982dfc90e206ea51f19bd650ccee2 |
|
26-May-2012 |
Masanari Iida <standby24x7@gmail.com> |
staging: comedi: Fix typo in comedi
Correct spelling typo in comments within staging/comedi.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 55c03cff7fd73349473cc0a964df9d55b312dbbc |
|
22-May-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: remove private header comedi_pci.h
Remove the private header, comedi_pci.h, by moving the two
helper functions into divers.c and providing the prototypes
in comedidev.h.
This allows the comedi_pci_enable/disable helper functions
to be shared instead of having an inline version in every
comedi pci driver.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 484ecc95d9cdfa8b2f7029e2f3409cf078aed4ab |
|
18-May-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: cleanup all the comedi_driver 'detach' functions
1. Change the return type from int to void
All the detach functions, except for the comedi usb drivers, simply
return success (0). Plus, the return code is never checked in the
comedi core.
The comedi usb drivers do return error codes but the conditions can
never happen.
The first check is:
if (!dev)
return -EFAULT;
This checks that the passed comedi_device pointer is valid. The detach
function itself is called using this pointer so it MUST always be valid
or there is a bug in the core:
if (dev->driver)
dev->driver->detach(dev);
And the second check:
usb = dev->private;
if (!usb)
return -EFAULT;
The dev->private pointer is setup in the attach function to point to the
probed usb device. This value could be NULL if the attach fails. But,
since the comedi core is going to unload the driver anyway and does not
check for errors there is no gain by returning one.
After removing these checks from the comedi usb drivers the detach
functions required a bit of cleanup.
2. Remove all the printk noise in the detach functions
All of the printk output is really just noise. The user did a rmmod to
unload the driver, we really don't need to tell them about it.
Also, some of the messages are output using:
dev_dbg(dev->hw_dev, ...
or
dev_info(dev->hw_dev, ...
Unfortunately the hw_dev value is only used by drivers that are doing
DMA. For most drivers this variable is going to be NULL so the output
is not going to work as expected.
3. Refactor a couple static 'free_resource' functions into the detach
functions.
The 'free_resource' function is only being called by the detach and it
makes more sense to just absorb the code.
4. Remove a couple unnecessary braces for single statements.
5. Remove unnecessary comments.
Most of the comedi drivers appear to be based on the comedi skel driver
and have the comments from that driver included. These comments make
sense in the skel driver for reference but they don't need to be in any
of the actual drivers.
6. Remove all the extra whitespace.
It's not needed to make the functions any more readable.
7. Remove the now unused 'attached_successfully' variable in the
cb_pcimdda driver.
This variable was only used to conditionally output some driver noise
during the detach. Since all the printk's have been removed this
variable is no longer necessary.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 75e6301baa78b2dff00e2cc3051301c32618acd7 |
|
12-May-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: Use module_comedi_pci_driver and standardize drivers
Convert the refactored comedi pci drivers to use the
module_comedi_pci_driver() macro which makes the code
smaller and a bit simpler.
In the process, rename some of the symbols in the driver
to standardize the comedi pci drivers.
Based on the driver {name}:
1) Rename the comedi_driver to {name}_driver.
2) Use a static string {name} for the comedi_driver.driver_name.
3) Rename the pci probe/remove functions to {name)_pci_probe/remove.
4) Rename the pci id_table to {name}_pci_table.
5) Add the static string {name} for the pci_driver.name.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| de9f2db41e6037fc4b9944edc62025327e4b9589 |
|
05-May-2012 |
H Hartley Sweeten <hartleys@visionengravers.com> |
staging: comedi: refactor dyna_pci10xx driver to remove forward declarations
Move the struct comedi_driver and associated variables to the
end of the source. This is more typical of how other drivers are
written and removes the need for the forward declarations.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 4c093a6dc2240fd54d71a25b284e02d51509e430 |
|
30-Mar-2012 |
Ian Abbott <abbotti@mev.co.uk> |
staging: comedi: pass 'struct comedi_driver *' to comedi_..._auto_config
The comedi_pci_auto_config() and comedi_usb_auto_config() functions
currently take a board name parameter which is actually a driver name
parameter. Replace it with a pointer to the struct comedi_driver. This
will allow comedi_pci_auto_config() and comedi_usb_auto_config() to call
bus-type-specific auto-configuration hooks in the struct comedi_driver
if they exist (they don't yet). The idea is that these
bus-type-specific auto-configuration hooks won't have to search the bus
for the device being auto-configured like 'attach()' hook has to.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 16a7373a8e1420cde99001759ec0eaf56f8931a5 |
|
12-Jun-2011 |
Prashant P. Shah <pshah.mumbai@gmail.com> |
Staging: comedi: add dyna_pci10xx driver
For Dynalog PCI DAQ cards:
PCI-1050
Signed-off-by: Prashant P. Shah <pshah.mumbai@gmail.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|