| 380c966c093e7239e42a81f165b20b2bad2658bc |
|
14-Jul-2014 |
Jingchang Lu <jingchang.lu@freescale.com> |
tty: serial: fsl_lpuart: add 32-bit register interface support
This add the 32-bit register version LPUART support with big-endian
byte order.
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| ed9891bf093638fad29f89c10b536550d29b129d |
|
02-Jul-2014 |
Stefan Agner <stefan@agner.ch> |
serial: fsl_lpuart: calculate DMA burst
The DMA burst size must match the transmit FIFO depth in order
to make sure all character are transmitted. This patch calculates
DMA burst size by using FIFO depth rather than use the hardcoded
16 bytes. This is required since some UARTs (e.g. UART2 on Vybrid)
have a FIFO depth of 8 bytes.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 90abef91c5974d3d4845d64fd75a319fb20f6e6b |
|
02-Jul-2014 |
Stefan Agner <stefan@agner.ch> |
serial: fsl_lpuart: move DMA RX timeout calculation
The DMA RX timeout calculation is done based on FIFO buffer size and
port timeout when setting up DMA. However, both variables are not
necessarily initialized at DMA initialization time, which can lead
to a division by zero.
Move the timeout calculation to set_termios where both variables
are initialized.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 8b152f1096975d012f60387b899d407e4a93b46c |
|
03-Jun-2014 |
Alexander Shiyan <shc_work@mail.ru> |
serial: treewide: Remove empty implementations of enable_ms()
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| ef8b9ddcb45fa3b1e11acd72be2398001e807d14 |
|
16-Jun-2014 |
Peter Hurley <peter@hurleysoftware.com> |
serial: Fix IGNBRK handling
If IGNBRK is set without either BRKINT or PARMRK set, some uart
drivers send a 0x00 byte for BREAK without the TTYBREAK flag to the
line discipline, when it should send either nothing or the TTYBREAK flag
set. This happens because the read_status_mask masks out the BI
condition, which uart_insert_char() then interprets as a normal 0x00 byte.
SUS v3 is clear regarding the meaning of IGNBRK; Section 11.2.2, General
Terminal Interface - Input Modes, states:
"If IGNBRK is set, a break condition detected on input shall be ignored;
that is, not put on the input queue and therefore not read by any
process."
Fix read_status_mask to include the BI bit if IGNBRK is set; the
lsr status retains the BI bit if a BREAK is recv'd, which is
subsequently ignored in uart_insert_char() when masked with the
ignore_status_mask.
Affected drivers:
8250 - all
serial_txx9
mfd
amba-pl010
amba-pl011
atmel_serial
bfin_uart
dz
ip22zilog
max310x
mxs-auart
netx-serial
pnx8xxx_uart
pxa
sb1250-duart
sccnxp
serial_ks8695
sirfsoc_uart
st-asc
vr41xx_siu
zs
sunzilog
fsl_lpuart
sunsab
ucc_uart
bcm63xx_uart
sunsu
efm32-uart
pmac_zilog
mpsc
msm_serial
m32r_sio
Unaffected drivers:
omap-serial
rp2
sa1100
imx
icom
Annotated for fixes:
altera_uart
mcf
Drivers without break detection:
21285
xilinx-uartps
altera_jtaguart
apbuart
arc-uart
clps711x
max3100
uartlite
msm_serial_hs
nwpserial
lantiq
vt8500_serial
Unknown:
samsung
mpc52xx_uart
bfin_sport_uart
cpm_uart/core
Fixes: Bugzilla #71651, '8250_core.c incorrectly handles IGNBRK flag'
Reported-by: Ivan <athlon_@mail.ru>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| f1cd8c8792ccc7e9520ef8f27fbdb748448ac482 |
|
17-Feb-2014 |
Yuan Yao <yao.yuan@freescale.com> |
serial: fsl_lpuart: add DMA support
Add dma support for lpuart. This function depend on DMA driver.
You can turn on it by write both the dmas and dma-name properties in dts node.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| 39c34b09f2fdb56c94891d5dd7ed4341d845cde5 |
|
22-Jul-2013 |
Axel Lin <axel.lin@ingics.com> |
serial: fsl_lpuart: Return proper error on lpuart_serial_init error path
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| bc764b8fdb4346cb21f624e08231267d0ea9578b |
|
08-Jul-2013 |
Shawn Guo <shawn.guo@linaro.org> |
serial: fsl_lpuart: restore UARTCR2 after watermark setup is done
Function lpuart_setup_watermark() clears some bits in register UARTCR2
before writing FIFO configuration registers as required by hardware.
But it should restore UARTCR2 after that. Otherwise, we end up changing
UARTCR2 register when setting up watermark, and that is not really
desirable. At least, when low-level debug and earlyprint is enabled,
serial console is broken due to it.
Fix the problem by restoring UARTCR2 register at the end of function
lpuart_setup_watermark().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
| c9e2e946fb0ba5d2398feb89558f98c5c28e23e3 |
|
07-Jun-2013 |
Jingchang Lu <b35083@freescale.com> |
tty: serial: add Freescale lpuart driver support
Add Freescale lpuart driver support. The lpuart device
can be found on Vybrid VF610 and Layerscape LS-1 SoCs.
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|