| 2e2271787419a12496bf5da5c3028a9c73c9697f |
|
09-Sep-2014 |
Brian Foster <bfoster@redhat.com> |
xfs: export log_recovery_delay to delay mount time log recovery
XFS log recovery has been discovered to have race conditions with
buffers when I/O errors occur. External tools are available to simulate
I/O errors to XFS, but this alone is not sufficient for testing log
recovery. XFS unconditionally resets the inactive region of the log
prior to log recovery to avoid confusion over processing any partially
written log records that might have been written before an unclean
shutdown. Therefore, unconditional write I/O failures at mount time are
caught by the reset sequence rather than log recovery and hinder the
ability to test the latter.
The device-mapper dm-flakey module uses an up/down timer to define a
cycle for when to fail I/Os. Create a pre log recovery delay tunable
that can be used to coordinate XFS log recovery with I/O errors
simulated by dm-flakey. This facilitates coordination in userspace that
allows the reset of stale log blocks to succeed and writes due to log
recovery to fail. For example, define a dm-flakey instance with an
uptime long enough to allow log reset to succeed and a log recovery
delay long enough to allow the dm-flakey uptime to expire.
The 'log_recovery_delay' sysfs tunable is exported under
/sys/fs/xfs/debug and is only enabled for kernels compiled in XFS debug
mode. The value is exported in units of seconds and allows for a delay
of up to 60 seconds. Note that this is for XFS debug and test
instrumentation purposes only and should not be used by applications. No
delay is enabled by default.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
|
| 65b65735fede29b516fed1d8c2391e8bc373b805 |
|
09-Sep-2014 |
Brian Foster <bfoster@redhat.com> |
xfs: add debug sysfs attribute set
Create a top-level debug directory for global debug sysfs attributes.
This directory is added and removed on XFS module initialization and
removal respectively for DEBUG mode kernels only. It typically resides
at /sys/fs/xfs/debug. It is located at the top level of the xfs sysfs
hierarchy as attributes might define global behavior or behavior that
must be configured before an xfs mount is available (e.g., log recovery
behavior).
Define the global debug kobject that represents the debug sysfs
directory and add generic attribute show/store helpers to support future
attributes. No debug attributes are exported as of yet.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
|
| 80d6d69821a27c3cd4687c2eefe409cbd1b7f458 |
|
15-Jul-2014 |
Brian Foster <bfoster@redhat.com> |
xfs: add log attributes for log lsn and grant head data
Create log attributes to export the current runtime state of the log to
sysfs. Note that the filesystem should be frozen for consistency across
attributes.
The following per-mount attributes are created: log_head_lsn,
log_tail_lsn, reserve_grant_head and write_grant_head. These represent
the physical log head, tail and reserve and write grant heads
respectively. Attribute values are exported in the following format:
"cycle:[block,byte]"
... where cycle represents the log cycle and [block,bytes] represents
either the basic block or byte offset of the log, depending on the
attribute. Log sequence number (LSN) values are encoded in basic blocks
and grant heads are encoded in bytes. All values are in decimal format.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
|
| baff4e44b92aad363dcce176b907a369ee8b348e |
|
15-Jul-2014 |
Brian Foster <bfoster@redhat.com> |
xfs: add xlog sysfs kobject and attribute handlers
Embed a kobject into the xfs log data structure (xlog). This creates a
'log' subdirectory for every XFS mount instance in sysfs. The lifecycle
of the log kobject is tied to the lifecycle of the log.
Also define a set of generic attribute handlers associated with the log
kobject in preparation for the addition of attributes.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
|
| a31b1d3d89e40f585a1c6745b066774ee3263eb2 |
|
15-Jul-2014 |
Brian Foster <bfoster@redhat.com> |
xfs: add xfs_mount sysfs kobject
Embed a base kobject into xfs_mount. This creates a kobject associated
with each XFS mount and a subdirectory in sysfs with the name of the
filesystem. The subdirectory lifecycle matches that of the mount. Also
add the new xfs_sysfs.[c,h] source files with some XFS sysfs
infrastructure to facilitate attribute creation.
Note that there are currently no attributes exported as part of the
xfs_mount kobject. It exists solely to serve as a per-mount container
for child objects.
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
|