Cross Reference: /drivers/char/lp.c

Lines Matching refs:lp
12  * "lp=" command line parameters added by Grant Guenther, grant@torque.net
43  *	lp=parport1,none,parport2	(bind lp0 to parport1, disable lp1 and
46  *	lp=auto				(assign lp devices to all ports that
50  *	lp=reset			(reset the printer during 
53  *	lp=off				(disable the printer driver entirely)
58  *	# insmod lp.o parport=1,none,2
60  *	# insmod lp.o parport=auto
62  *	# insmod lp.o reset=1
67  * Under Linux 2.0 and previous versions, lp devices were bound to ports at
74  * The new driver, by default, binds lp devices to parport devices as it
97  * generates the irq on the _rising_ edge of the STROBE. Now lp handle
105  * break drivers or legacy application, while they broken linux lp
134 #include <linux/lp.h>
245 			printk(KERN_INFO "lp%d out of paper\n", minor);
251 			printk(KERN_INFO "lp%d off-line\n", minor);
257 			printk(KERN_INFO "lp%d on fire\n", minor);
397 		printk(KERN_INFO "lp%d releasing parport\n", minor);
520 			printk(KERN_INFO "lp%d out of paper\n", minor);
525 			printk(KERN_INFO "lp%d off-line\n", minor);
530 			printk(KERN_ERR "lp%d printer error\n", minor);
547 		printk (KERN_INFO "lp%d: ECP mode\n", minor);
582 	printk(KERN_DEBUG "lp%d ioctl, cmd: 0x%x, arg: 0x%lx\n", minor, cmd, arg);
822 	.name		= "lp",
846 			/* disable driver on "lp=" or "lp=0" */
849 			printk(KERN_WARNING "warning: 'lp=0x%x' is deprecated, ignored\n", x);
857 			printk(KERN_INFO "lp: too many ports, %s ignored.\n",
872 	lp_table[nr].dev = parport_register_device(port, "lp", 
883 		      "lp%d", nr);
885 	printk(KERN_INFO "lp%d: using %s (%s).\n", nr, port->name, 
893 			printk (KERN_INFO "lp%d: console ready\n", CONSOLE_LP);
895 			printk (KERN_ERR "lp%d: cannot run console on %s\n",
914 			printk(KERN_INFO "lp: ignoring parallel port (max. %d)\n",LP_NO);
945 	.name = "lp",
976 	if (register_chrdev (LP_MAJOR, "lp", &lp_fops)) {
977 		printk (KERN_ERR "lp: unable to get major %d\n", LP_MAJOR);
988 		printk (KERN_ERR "lp: unable to register with parport\n");
994 		printk (KERN_INFO "lp: driver loaded but no devices found\n");
997 			printk (KERN_INFO "lp: (is IEEE 1284 support enabled?)\n");
1006 	unregister_chrdev(LP_MAJOR, "lp");
1027 						printk(KERN_ERR "lp: bad port specifier `%s'\n", parport[n]);
1048 	unregister_chrdev(LP_MAJOR, "lp");
1058 __setup("lp=", lp_setup);