1/* 2 * This file function prototypes, data structure 3 * and definitions for all the host/station commands 4 */ 5 6#ifndef _LBS_HOST_H_ 7#define _LBS_HOST_H_ 8 9#include "types.h" 10#include "defs.h" 11 12#define DEFAULT_AD_HOC_CHANNEL 6 13 14#define CMD_OPTION_WAITFORRSP 0x0002 15 16/* Host command IDs */ 17 18/* 19 * Return command are almost always the same as the host command, but with 20 * bit 15 set high. There are a few exceptions, though... 21 */ 22#define CMD_RET(cmd) (0x8000 | cmd) 23 24/* Return command convention exceptions: */ 25#define CMD_RET_802_11_ASSOCIATE 0x8012 26 27/* Command codes */ 28#define CMD_GET_HW_SPEC 0x0003 29#define CMD_EEPROM_UPDATE 0x0004 30#define CMD_802_11_RESET 0x0005 31#define CMD_802_11_SCAN 0x0006 32#define CMD_802_11_GET_LOG 0x000b 33#define CMD_MAC_MULTICAST_ADR 0x0010 34#define CMD_802_11_AUTHENTICATE 0x0011 35#define CMD_802_11_EEPROM_ACCESS 0x0059 36#define CMD_802_11_ASSOCIATE 0x0050 37#define CMD_802_11_SET_WEP 0x0013 38#define CMD_802_11_GET_STAT 0x0014 39#define CMD_802_3_GET_STAT 0x0015 40#define CMD_802_11_SNMP_MIB 0x0016 41#define CMD_MAC_REG_MAP 0x0017 42#define CMD_BBP_REG_MAP 0x0018 43#define CMD_MAC_REG_ACCESS 0x0019 44#define CMD_BBP_REG_ACCESS 0x001a 45#define CMD_RF_REG_ACCESS 0x001b 46#define CMD_802_11_RADIO_CONTROL 0x001c 47#define CMD_802_11_RF_CHANNEL 0x001d 48#define CMD_802_11_RF_TX_POWER 0x001e 49#define CMD_802_11_RSSI 0x001f 50#define CMD_802_11_RF_ANTENNA 0x0020 51#define CMD_802_11_PS_MODE 0x0021 52#define CMD_802_11_DATA_RATE 0x0022 53#define CMD_RF_REG_MAP 0x0023 54#define CMD_802_11_DEAUTHENTICATE 0x0024 55#define CMD_802_11_REASSOCIATE 0x0025 56#define CMD_MAC_CONTROL 0x0028 57#define CMD_802_11_AD_HOC_START 0x002b 58#define CMD_802_11_AD_HOC_JOIN 0x002c 59#define CMD_802_11_QUERY_TKIP_REPLY_CNTRS 0x002e 60#define CMD_802_11_ENABLE_RSN 0x002f 61#define CMD_802_11_SET_AFC 0x003c 62#define CMD_802_11_GET_AFC 0x003d 63#define CMD_802_11_DEEP_SLEEP 0x003e 64#define CMD_802_11_AD_HOC_STOP 0x0040 65#define CMD_802_11_HOST_SLEEP_CFG 0x0043 66#define CMD_802_11_WAKEUP_CONFIRM 0x0044 67#define CMD_802_11_HOST_SLEEP_ACTIVATE 0x0045 68#define CMD_802_11_BEACON_STOP 0x0049 69#define CMD_802_11_MAC_ADDRESS 0x004d 70#define CMD_802_11_LED_GPIO_CTRL 0x004e 71#define CMD_802_11_BAND_CONFIG 0x0058 72#define CMD_GSPI_BUS_CONFIG 0x005a 73#define CMD_802_11D_DOMAIN_INFO 0x005b 74#define CMD_802_11_KEY_MATERIAL 0x005e 75#define CMD_802_11_SLEEP_PARAMS 0x0066 76#define CMD_802_11_INACTIVITY_TIMEOUT 0x0067 77#define CMD_802_11_SLEEP_PERIOD 0x0068 78#define CMD_802_11_TPC_CFG 0x0072 79#define CMD_802_11_PA_CFG 0x0073 80#define CMD_802_11_FW_WAKE_METHOD 0x0074 81#define CMD_802_11_SUBSCRIBE_EVENT 0x0075 82#define CMD_802_11_RATE_ADAPT_RATESET 0x0076 83#define CMD_802_11_TX_RATE_QUERY 0x007f 84#define CMD_GET_TSF 0x0080 85#define CMD_BT_ACCESS 0x0087 86#define CMD_FWT_ACCESS 0x0095 87#define CMD_802_11_MONITOR_MODE 0x0098 88#define CMD_MESH_ACCESS 0x009b 89#define CMD_MESH_CONFIG_OLD 0x00a3 90#define CMD_MESH_CONFIG 0x00ac 91#define CMD_SET_BOOT2_VER 0x00a5 92#define CMD_FUNC_INIT 0x00a9 93#define CMD_FUNC_SHUTDOWN 0x00aa 94#define CMD_802_11_BEACON_CTRL 0x00b0 95 96/* For the IEEE Power Save */ 97#define PS_MODE_ACTION_ENTER_PS 0x0030 98#define PS_MODE_ACTION_EXIT_PS 0x0031 99#define PS_MODE_ACTION_SLEEP_CONFIRMED 0x0034 100 101#define CMD_ENABLE_RSN 0x0001 102#define CMD_DISABLE_RSN 0x0000 103 104#define CMD_ACT_GET 0x0000 105#define CMD_ACT_SET 0x0001 106 107/* Define action or option for CMD_802_11_SET_WEP */ 108#define CMD_ACT_ADD 0x0002 109#define CMD_ACT_REMOVE 0x0004 110 111#define CMD_TYPE_WEP_40_BIT 0x01 112#define CMD_TYPE_WEP_104_BIT 0x02 113 114#define CMD_NUM_OF_WEP_KEYS 4 115 116#define CMD_WEP_KEY_INDEX_MASK 0x3fff 117 118/* Define action or option for CMD_802_11_SCAN */ 119#define CMD_BSS_TYPE_BSS 0x0001 120#define CMD_BSS_TYPE_IBSS 0x0002 121#define CMD_BSS_TYPE_ANY 0x0003 122 123/* Define action or option for CMD_802_11_SCAN */ 124#define CMD_SCAN_TYPE_ACTIVE 0x0000 125#define CMD_SCAN_TYPE_PASSIVE 0x0001 126 127#define CMD_SCAN_RADIO_TYPE_BG 0 128 129#define CMD_SCAN_PROBE_DELAY_TIME 0 130 131/* Define action or option for CMD_MAC_CONTROL */ 132#define CMD_ACT_MAC_RX_ON 0x0001 133#define CMD_ACT_MAC_TX_ON 0x0002 134#define CMD_ACT_MAC_LOOPBACK_ON 0x0004 135#define CMD_ACT_MAC_WEP_ENABLE 0x0008 136#define CMD_ACT_MAC_INT_ENABLE 0x0010 137#define CMD_ACT_MAC_MULTICAST_ENABLE 0x0020 138#define CMD_ACT_MAC_BROADCAST_ENABLE 0x0040 139#define CMD_ACT_MAC_PROMISCUOUS_ENABLE 0x0080 140#define CMD_ACT_MAC_ALL_MULTICAST_ENABLE 0x0100 141#define CMD_ACT_MAC_STRICT_PROTECTION_ENABLE 0x0400 142 143/* Event flags for CMD_802_11_SUBSCRIBE_EVENT */ 144#define CMD_SUBSCRIBE_RSSI_LOW 0x0001 145#define CMD_SUBSCRIBE_SNR_LOW 0x0002 146#define CMD_SUBSCRIBE_FAILCOUNT 0x0004 147#define CMD_SUBSCRIBE_BCNMISS 0x0008 148#define CMD_SUBSCRIBE_RSSI_HIGH 0x0010 149#define CMD_SUBSCRIBE_SNR_HIGH 0x0020 150 151#define RADIO_PREAMBLE_LONG 0x00 152#define RADIO_PREAMBLE_SHORT 0x02 153#define RADIO_PREAMBLE_AUTO 0x04 154 155/* Define action or option for CMD_802_11_RF_CHANNEL */ 156#define CMD_OPT_802_11_RF_CHANNEL_GET 0x00 157#define CMD_OPT_802_11_RF_CHANNEL_SET 0x01 158 159/* Define action or option for CMD_802_11_DATA_RATE */ 160#define CMD_ACT_SET_TX_AUTO 0x0000 161#define CMD_ACT_SET_TX_FIX_RATE 0x0001 162#define CMD_ACT_GET_TX_RATE 0x0002 163 164/* Options for CMD_802_11_FW_WAKE_METHOD */ 165#define CMD_WAKE_METHOD_UNCHANGED 0x0000 166#define CMD_WAKE_METHOD_COMMAND_INT 0x0001 167#define CMD_WAKE_METHOD_GPIO 0x0002 168 169/* Object IDs for CMD_802_11_SNMP_MIB */ 170#define SNMP_MIB_OID_BSS_TYPE 0x0000 171#define SNMP_MIB_OID_OP_RATE_SET 0x0001 172#define SNMP_MIB_OID_BEACON_PERIOD 0x0002 /* Reserved on v9+ */ 173#define SNMP_MIB_OID_DTIM_PERIOD 0x0003 /* Reserved on v9+ */ 174#define SNMP_MIB_OID_ASSOC_TIMEOUT 0x0004 /* Reserved on v9+ */ 175#define SNMP_MIB_OID_RTS_THRESHOLD 0x0005 176#define SNMP_MIB_OID_SHORT_RETRY_LIMIT 0x0006 177#define SNMP_MIB_OID_LONG_RETRY_LIMIT 0x0007 178#define SNMP_MIB_OID_FRAG_THRESHOLD 0x0008 179#define SNMP_MIB_OID_11D_ENABLE 0x0009 180#define SNMP_MIB_OID_11H_ENABLE 0x000A 181 182/* Define action or option for CMD_BT_ACCESS */ 183enum cmd_bt_access_opts { 184 /* The bt commands start at 5 instead of 1 because the old dft commands 185 * are mapped to 1-4. These old commands are no longer maintained and 186 * should not be called. 187 */ 188 CMD_ACT_BT_ACCESS_ADD = 5, 189 CMD_ACT_BT_ACCESS_DEL, 190 CMD_ACT_BT_ACCESS_LIST, 191 CMD_ACT_BT_ACCESS_RESET, 192 CMD_ACT_BT_ACCESS_SET_INVERT, 193 CMD_ACT_BT_ACCESS_GET_INVERT 194}; 195 196/* Define action or option for CMD_FWT_ACCESS */ 197enum cmd_fwt_access_opts { 198 CMD_ACT_FWT_ACCESS_ADD = 1, 199 CMD_ACT_FWT_ACCESS_DEL, 200 CMD_ACT_FWT_ACCESS_LOOKUP, 201 CMD_ACT_FWT_ACCESS_LIST, 202 CMD_ACT_FWT_ACCESS_LIST_ROUTE, 203 CMD_ACT_FWT_ACCESS_LIST_NEIGHBOR, 204 CMD_ACT_FWT_ACCESS_RESET, 205 CMD_ACT_FWT_ACCESS_CLEANUP, 206 CMD_ACT_FWT_ACCESS_TIME, 207}; 208 209/* Define action or option for CMD_802_11_HOST_SLEEP_CFG */ 210enum cmd_wol_cfg_opts { 211 CMD_ACT_ACTION_NONE = 0, 212 CMD_ACT_SET_WOL_RULE, 213 CMD_ACT_GET_WOL_RULE, 214 CMD_ACT_RESET_WOL_RULE, 215}; 216 217/* Define action or option for CMD_MESH_ACCESS */ 218enum cmd_mesh_access_opts { 219 CMD_ACT_MESH_GET_TTL = 1, 220 CMD_ACT_MESH_SET_TTL, 221 CMD_ACT_MESH_GET_STATS, 222 CMD_ACT_MESH_GET_ANYCAST, 223 CMD_ACT_MESH_SET_ANYCAST, 224 CMD_ACT_MESH_SET_LINK_COSTS, 225 CMD_ACT_MESH_GET_LINK_COSTS, 226 CMD_ACT_MESH_SET_BCAST_RATE, 227 CMD_ACT_MESH_GET_BCAST_RATE, 228 CMD_ACT_MESH_SET_RREQ_DELAY, 229 CMD_ACT_MESH_GET_RREQ_DELAY, 230 CMD_ACT_MESH_SET_ROUTE_EXP, 231 CMD_ACT_MESH_GET_ROUTE_EXP, 232 CMD_ACT_MESH_SET_AUTOSTART_ENABLED, 233 CMD_ACT_MESH_GET_AUTOSTART_ENABLED, 234 CMD_ACT_MESH_SET_GET_PRB_RSP_LIMIT = 17, 235}; 236 237/* Define actions and types for CMD_MESH_CONFIG */ 238enum cmd_mesh_config_actions { 239 CMD_ACT_MESH_CONFIG_STOP = 0, 240 CMD_ACT_MESH_CONFIG_START, 241 CMD_ACT_MESH_CONFIG_SET, 242 CMD_ACT_MESH_CONFIG_GET, 243}; 244 245enum cmd_mesh_config_types { 246 CMD_TYPE_MESH_SET_BOOTFLAG = 1, 247 CMD_TYPE_MESH_SET_BOOTTIME, 248 CMD_TYPE_MESH_SET_DEF_CHANNEL, 249 CMD_TYPE_MESH_SET_MESH_IE, 250 CMD_TYPE_MESH_GET_DEFAULTS, 251 CMD_TYPE_MESH_GET_MESH_IE, /* GET_DEFAULTS is superset of GET_MESHIE */ 252}; 253 254/* Card Event definition */ 255#define MACREG_INT_CODE_TX_PPA_FREE 0 256#define MACREG_INT_CODE_TX_DMA_DONE 1 257#define MACREG_INT_CODE_LINK_LOST_W_SCAN 2 258#define MACREG_INT_CODE_LINK_LOST_NO_SCAN 3 259#define MACREG_INT_CODE_LINK_SENSED 4 260#define MACREG_INT_CODE_CMD_FINISHED 5 261#define MACREG_INT_CODE_MIB_CHANGED 6 262#define MACREG_INT_CODE_INIT_DONE 7 263#define MACREG_INT_CODE_DEAUTHENTICATED 8 264#define MACREG_INT_CODE_DISASSOCIATED 9 265#define MACREG_INT_CODE_PS_AWAKE 10 266#define MACREG_INT_CODE_PS_SLEEP 11 267#define MACREG_INT_CODE_MIC_ERR_MULTICAST 13 268#define MACREG_INT_CODE_MIC_ERR_UNICAST 14 269#define MACREG_INT_CODE_WM_AWAKE 15 270#define MACREG_INT_CODE_DEEP_SLEEP_AWAKE 16 271#define MACREG_INT_CODE_ADHOC_BCN_LOST 17 272#define MACREG_INT_CODE_HOST_AWAKE 18 273#define MACREG_INT_CODE_STOP_TX 19 274#define MACREG_INT_CODE_START_TX 20 275#define MACREG_INT_CODE_CHANNEL_SWITCH 21 276#define MACREG_INT_CODE_MEASUREMENT_RDY 22 277#define MACREG_INT_CODE_WMM_CHANGE 23 278#define MACREG_INT_CODE_BG_SCAN_REPORT 24 279#define MACREG_INT_CODE_RSSI_LOW 25 280#define MACREG_INT_CODE_SNR_LOW 26 281#define MACREG_INT_CODE_MAX_FAIL 27 282#define MACREG_INT_CODE_RSSI_HIGH 28 283#define MACREG_INT_CODE_SNR_HIGH 29 284#define MACREG_INT_CODE_MESH_AUTO_STARTED 35 285#define MACREG_INT_CODE_FIRMWARE_READY 48 286 287 288/* 802.11-related definitions */ 289 290/* TxPD descriptor */ 291struct txpd { 292 /* union to cope up with later FW revisions */ 293 union { 294 /* Current Tx packet status */ 295 __le32 tx_status; 296 struct { 297 /* BSS type: client, AP, etc. */ 298 u8 bss_type; 299 /* BSS number */ 300 u8 bss_num; 301 /* Reserved */ 302 __le16 reserved; 303 } bss; 304 } u; 305 /* Tx control */ 306 __le32 tx_control; 307 __le32 tx_packet_location; 308 /* Tx packet length */ 309 __le16 tx_packet_length; 310 /* First 2 byte of destination MAC address */ 311 u8 tx_dest_addr_high[2]; 312 /* Last 4 byte of destination MAC address */ 313 u8 tx_dest_addr_low[4]; 314 /* Pkt Priority */ 315 u8 priority; 316 /* Pkt Trasnit Power control */ 317 u8 powermgmt; 318 /* Amount of time the packet has been queued (units = 2ms) */ 319 u8 pktdelay_2ms; 320 /* reserved */ 321 u8 reserved1; 322} __packed; 323 324/* RxPD Descriptor */ 325struct rxpd { 326 /* union to cope up with later FW revisions */ 327 union { 328 /* Current Rx packet status */ 329 __le16 status; 330 struct { 331 /* BSS type: client, AP, etc. */ 332 u8 bss_type; 333 /* BSS number */ 334 u8 bss_num; 335 } __packed bss; 336 } __packed u; 337 338 /* SNR */ 339 u8 snr; 340 341 /* Tx control */ 342 u8 rx_control; 343 344 /* Pkt length */ 345 __le16 pkt_len; 346 347 /* Noise Floor */ 348 u8 nf; 349 350 /* Rx Packet Rate */ 351 u8 rx_rate; 352 353 /* Pkt addr */ 354 __le32 pkt_ptr; 355 356 /* Next Rx RxPD addr */ 357 __le32 next_rxpd_ptr; 358 359 /* Pkt Priority */ 360 u8 priority; 361 u8 reserved[3]; 362} __packed; 363 364struct cmd_header { 365 __le16 command; 366 __le16 size; 367 __le16 seqnum; 368 __le16 result; 369} __packed; 370 371/* Generic structure to hold all key types. */ 372struct enc_key { 373 u16 len; 374 u16 flags; /* KEY_INFO_* from defs.h */ 375 u16 type; /* KEY_TYPE_* from defs.h */ 376 u8 key[32]; 377}; 378 379/* lbs_offset_value */ 380struct lbs_offset_value { 381 u32 offset; 382 u32 value; 383} __packed; 384 385#define MAX_11D_TRIPLETS 83 386 387struct mrvl_ie_domain_param_set { 388 struct mrvl_ie_header header; 389 390 u8 country_code[IEEE80211_COUNTRY_STRING_LEN]; 391 struct ieee80211_country_ie_triplet triplet[MAX_11D_TRIPLETS]; 392} __packed; 393 394struct cmd_ds_802_11d_domain_info { 395 struct cmd_header hdr; 396 397 __le16 action; 398 struct mrvl_ie_domain_param_set domain; 399} __packed; 400 401/* 402 * Define data structure for CMD_GET_HW_SPEC 403 * This structure defines the response for the GET_HW_SPEC command 404 */ 405struct cmd_ds_get_hw_spec { 406 struct cmd_header hdr; 407 408 /* HW Interface version number */ 409 __le16 hwifversion; 410 /* HW version number */ 411 __le16 version; 412 /* Max number of TxPD FW can handle */ 413 __le16 nr_txpd; 414 /* Max no of Multicast address */ 415 __le16 nr_mcast_adr; 416 /* MAC address */ 417 u8 permanentaddr[6]; 418 419 /* region Code */ 420 __le16 regioncode; 421 422 /* Number of antenna used */ 423 __le16 nr_antenna; 424 425 /* FW release number, example 0x01030304 = 2.3.4p1 */ 426 __le32 fwrelease; 427 428 /* Base Address of TxPD queue */ 429 __le32 wcb_base; 430 /* Read Pointer of RxPd queue */ 431 __le32 rxpd_rdptr; 432 433 /* Write Pointer of RxPd queue */ 434 __le32 rxpd_wrptr; 435 436 /*FW/HW capability */ 437 __le32 fwcapinfo; 438} __packed; 439 440struct cmd_ds_802_11_subscribe_event { 441 struct cmd_header hdr; 442 443 __le16 action; 444 __le16 events; 445 446 /* A TLV to the CMD_802_11_SUBSCRIBE_EVENT command can contain a 447 * number of TLVs. From the v5.1 manual, those TLVs would add up to 448 * 40 bytes. However, future firmware might add additional TLVs, so I 449 * bump this up a bit. 450 */ 451 uint8_t tlv[128]; 452} __packed; 453 454/* 455 * This scan handle Country Information IE(802.11d compliant) 456 * Define data structure for CMD_802_11_SCAN 457 */ 458struct cmd_ds_802_11_scan { 459 struct cmd_header hdr; 460 461 uint8_t bsstype; 462 uint8_t bssid[ETH_ALEN]; 463 uint8_t tlvbuffer[0]; 464} __packed; 465 466struct cmd_ds_802_11_scan_rsp { 467 struct cmd_header hdr; 468 469 __le16 bssdescriptsize; 470 uint8_t nr_sets; 471 uint8_t bssdesc_and_tlvbuffer[0]; 472} __packed; 473 474struct cmd_ds_802_11_get_log { 475 struct cmd_header hdr; 476 477 __le32 mcasttxframe; 478 __le32 failed; 479 __le32 retry; 480 __le32 multiretry; 481 __le32 framedup; 482 __le32 rtssuccess; 483 __le32 rtsfailure; 484 __le32 ackfailure; 485 __le32 rxfrag; 486 __le32 mcastrxframe; 487 __le32 fcserror; 488 __le32 txframe; 489 __le32 wepundecryptable; 490} __packed; 491 492struct cmd_ds_mac_control { 493 struct cmd_header hdr; 494 __le16 action; 495 u16 reserved; 496} __packed; 497 498struct cmd_ds_mac_multicast_adr { 499 struct cmd_header hdr; 500 __le16 action; 501 __le16 nr_of_adrs; 502 u8 maclist[ETH_ALEN * MRVDRV_MAX_MULTICAST_LIST_SIZE]; 503} __packed; 504 505struct cmd_ds_802_11_authenticate { 506 struct cmd_header hdr; 507 508 u8 bssid[ETH_ALEN]; 509 u8 authtype; 510 u8 reserved[10]; 511} __packed; 512 513struct cmd_ds_802_11_deauthenticate { 514 struct cmd_header hdr; 515 516 u8 macaddr[ETH_ALEN]; 517 __le16 reasoncode; 518} __packed; 519 520struct cmd_ds_802_11_associate { 521 struct cmd_header hdr; 522 523 u8 bssid[6]; 524 __le16 capability; 525 __le16 listeninterval; 526 __le16 bcnperiod; 527 u8 dtimperiod; 528 u8 iebuf[512]; /* Enough for required and most optional IEs */ 529} __packed; 530 531struct cmd_ds_802_11_associate_response { 532 struct cmd_header hdr; 533 534 __le16 capability; 535 __le16 statuscode; 536 __le16 aid; 537 u8 iebuf[512]; 538} __packed; 539 540struct cmd_ds_802_11_set_wep { 541 struct cmd_header hdr; 542 543 /* ACT_ADD, ACT_REMOVE or ACT_ENABLE */ 544 __le16 action; 545 546 /* key Index selected for Tx */ 547 __le16 keyindex; 548 549 /* 40, 128bit or TXWEP */ 550 uint8_t keytype[4]; 551 uint8_t keymaterial[4][16]; 552} __packed; 553 554struct cmd_ds_802_11_snmp_mib { 555 struct cmd_header hdr; 556 557 __le16 action; 558 __le16 oid; 559 __le16 bufsize; 560 u8 value[128]; 561} __packed; 562 563struct cmd_ds_reg_access { 564 struct cmd_header hdr; 565 566 __le16 action; 567 __le16 offset; 568 union { 569 u8 bbp_rf; /* for BBP and RF registers */ 570 __le32 mac; /* for MAC registers */ 571 } value; 572} __packed; 573 574struct cmd_ds_802_11_radio_control { 575 struct cmd_header hdr; 576 577 __le16 action; 578 __le16 control; 579} __packed; 580 581struct cmd_ds_802_11_beacon_control { 582 struct cmd_header hdr; 583 584 __le16 action; 585 __le16 beacon_enable; 586 __le16 beacon_period; 587} __packed; 588 589struct cmd_ds_802_11_sleep_params { 590 struct cmd_header hdr; 591 592 /* ACT_GET/ACT_SET */ 593 __le16 action; 594 595 /* Sleep clock error in ppm */ 596 __le16 error; 597 598 /* Wakeup offset in usec */ 599 __le16 offset; 600 601 /* Clock stabilization time in usec */ 602 __le16 stabletime; 603 604 /* control periodic calibration */ 605 uint8_t calcontrol; 606 607 /* control the use of external sleep clock */ 608 uint8_t externalsleepclk; 609 610 /* reserved field, should be set to zero */ 611 __le16 reserved; 612} __packed; 613 614struct cmd_ds_802_11_rf_channel { 615 struct cmd_header hdr; 616 617 __le16 action; 618 __le16 channel; 619 __le16 rftype; /* unused */ 620 __le16 reserved; /* unused */ 621 u8 channellist[32]; /* unused */ 622} __packed; 623 624struct cmd_ds_802_11_rssi { 625 struct cmd_header hdr; 626 627 /* 628 * request: number of beacons (N) to average the SNR and NF over 629 * response: SNR of most recent beacon 630 */ 631 __le16 n_or_snr; 632 633 /* 634 * The following fields are only set in the response. 635 * In the request these are reserved and should be set to 0. 636 */ 637 __le16 nf; /* most recent beacon noise floor */ 638 __le16 avg_snr; /* average SNR weighted by N from request */ 639 __le16 avg_nf; /* average noise floor weighted by N from request */ 640} __packed; 641 642struct cmd_ds_802_11_mac_address { 643 struct cmd_header hdr; 644 645 __le16 action; 646 u8 macadd[ETH_ALEN]; 647} __packed; 648 649struct cmd_ds_802_11_rf_tx_power { 650 struct cmd_header hdr; 651 652 __le16 action; 653 __le16 curlevel; 654 s8 maxlevel; 655 s8 minlevel; 656} __packed; 657 658/* MONITOR_MODE only exists in OLPC v5 firmware */ 659struct cmd_ds_802_11_monitor_mode { 660 struct cmd_header hdr; 661 662 __le16 action; 663 __le16 mode; 664} __packed; 665 666struct cmd_ds_set_boot2_ver { 667 struct cmd_header hdr; 668 669 __le16 action; 670 __le16 version; 671} __packed; 672 673struct cmd_ds_802_11_fw_wake_method { 674 struct cmd_header hdr; 675 676 __le16 action; 677 __le16 method; 678} __packed; 679 680struct cmd_ds_802_11_ps_mode { 681 struct cmd_header hdr; 682 683 __le16 action; 684 685 /* 686 * Interval for keepalive in PS mode: 687 * 0x0000 = don't change 688 * 0x001E = firmware default 689 * 0xFFFF = disable 690 */ 691 __le16 nullpktinterval; 692 693 /* 694 * Number of DTIM intervals to wake up for: 695 * 0 = don't change 696 * 1 = firmware default 697 * 5 = max 698 */ 699 __le16 multipledtim; 700 701 __le16 reserved; 702 __le16 locallisteninterval; 703 704 /* 705 * AdHoc awake period (FW v9+ only): 706 * 0 = don't change 707 * 1 = always awake (IEEE standard behavior) 708 * 2 - 31 = sleep for (n - 1) periods and awake for 1 period 709 * 32 - 254 = invalid 710 * 255 = sleep at each ATIM 711 */ 712 __le16 adhoc_awake_period; 713} __packed; 714 715struct cmd_confirm_sleep { 716 struct cmd_header hdr; 717 718 __le16 action; 719 __le16 nullpktinterval; 720 __le16 multipledtim; 721 __le16 reserved; 722 __le16 locallisteninterval; 723} __packed; 724 725struct cmd_ds_802_11_data_rate { 726 struct cmd_header hdr; 727 728 __le16 action; 729 __le16 reserved; 730 u8 rates[MAX_RATES]; 731} __packed; 732 733struct cmd_ds_802_11_rate_adapt_rateset { 734 struct cmd_header hdr; 735 __le16 action; 736 __le16 enablehwauto; 737 __le16 bitmap; 738} __packed; 739 740struct cmd_ds_802_11_ad_hoc_start { 741 struct cmd_header hdr; 742 743 u8 ssid[IEEE80211_MAX_SSID_LEN]; 744 u8 bsstype; 745 __le16 beaconperiod; 746 u8 dtimperiod; /* Reserved on v9 and later */ 747 struct ieee_ie_ibss_param_set ibss; 748 u8 reserved1[4]; 749 struct ieee_ie_ds_param_set ds; 750 u8 reserved2[4]; 751 __le16 probedelay; /* Reserved on v9 and later */ 752 __le16 capability; 753 u8 rates[MAX_RATES]; 754 u8 tlv_memory_size_pad[100]; 755} __packed; 756 757struct cmd_ds_802_11_ad_hoc_result { 758 struct cmd_header hdr; 759 760 u8 pad[3]; 761 u8 bssid[ETH_ALEN]; 762} __packed; 763 764struct adhoc_bssdesc { 765 u8 bssid[ETH_ALEN]; 766 u8 ssid[IEEE80211_MAX_SSID_LEN]; 767 u8 type; 768 __le16 beaconperiod; 769 u8 dtimperiod; 770 __le64 timestamp; 771 __le64 localtime; 772 struct ieee_ie_ds_param_set ds; 773 u8 reserved1[4]; 774 struct ieee_ie_ibss_param_set ibss; 775 u8 reserved2[4]; 776 __le16 capability; 777 u8 rates[MAX_RATES]; 778 779 /* 780 * DO NOT ADD ANY FIELDS TO THIS STRUCTURE. It is used below in the 781 * Adhoc join command and will cause a binary layout mismatch with 782 * the firmware 783 */ 784} __packed; 785 786struct cmd_ds_802_11_ad_hoc_join { 787 struct cmd_header hdr; 788 789 struct adhoc_bssdesc bss; 790 __le16 failtimeout; /* Reserved on v9 and later */ 791 __le16 probedelay; /* Reserved on v9 and later */ 792} __packed; 793 794struct cmd_ds_802_11_ad_hoc_stop { 795 struct cmd_header hdr; 796} __packed; 797 798struct cmd_ds_802_11_enable_rsn { 799 struct cmd_header hdr; 800 801 __le16 action; 802 __le16 enable; 803} __packed; 804 805struct MrvlIEtype_keyParamSet { 806 /* type ID */ 807 __le16 type; 808 809 /* length of Payload */ 810 __le16 length; 811 812 /* type of key: WEP=0, TKIP=1, AES=2 */ 813 __le16 keytypeid; 814 815 /* key control Info specific to a keytypeid */ 816 __le16 keyinfo; 817 818 /* length of key */ 819 __le16 keylen; 820 821 /* key material of size keylen */ 822 u8 key[32]; 823} __packed; 824 825#define MAX_WOL_RULES 16 826 827struct host_wol_rule { 828 uint8_t rule_no; 829 uint8_t rule_ops; 830 __le16 sig_offset; 831 __le16 sig_length; 832 __le16 reserve; 833 __be32 sig_mask; 834 __be32 signature; 835} __packed; 836 837struct wol_config { 838 uint8_t action; 839 uint8_t pattern; 840 uint8_t no_rules_in_cmd; 841 uint8_t result; 842 struct host_wol_rule rule[MAX_WOL_RULES]; 843} __packed; 844 845struct cmd_ds_host_sleep { 846 struct cmd_header hdr; 847 __le32 criteria; 848 uint8_t gpio; 849 uint16_t gap; 850 struct wol_config wol_conf; 851} __packed; 852 853 854 855struct cmd_ds_802_11_key_material { 856 struct cmd_header hdr; 857 858 __le16 action; 859 struct MrvlIEtype_keyParamSet keyParamSet[2]; 860} __packed; 861 862struct cmd_ds_802_11_eeprom_access { 863 struct cmd_header hdr; 864 __le16 action; 865 __le16 offset; 866 __le16 len; 867 /* firmware says it returns a maximum of 20 bytes */ 868#define LBS_EEPROM_READ_LEN 20 869 u8 value[LBS_EEPROM_READ_LEN]; 870} __packed; 871 872struct cmd_ds_802_11_tpc_cfg { 873 struct cmd_header hdr; 874 875 __le16 action; 876 uint8_t enable; 877 int8_t P0; 878 int8_t P1; 879 int8_t P2; 880 uint8_t usesnr; 881} __packed; 882 883 884struct cmd_ds_802_11_pa_cfg { 885 struct cmd_header hdr; 886 887 __le16 action; 888 uint8_t enable; 889 int8_t P0; 890 int8_t P1; 891 int8_t P2; 892} __packed; 893 894 895struct cmd_ds_802_11_led_ctrl { 896 struct cmd_header hdr; 897 898 __le16 action; 899 __le16 numled; 900 u8 data[256]; 901} __packed; 902 903/* Automatic Frequency Control */ 904struct cmd_ds_802_11_afc { 905 struct cmd_header hdr; 906 907 __le16 afc_auto; 908 union { 909 struct { 910 __le16 threshold; 911 __le16 period; 912 }; 913 struct { 914 __le16 timing_offset; /* signed */ 915 __le16 carrier_offset; /* signed */ 916 }; 917 }; 918} __packed; 919 920struct cmd_tx_rate_query { 921 __le16 txrate; 922} __packed; 923 924struct cmd_ds_get_tsf { 925 __le64 tsfvalue; 926} __packed; 927 928struct cmd_ds_bt_access { 929 struct cmd_header hdr; 930 931 __le16 action; 932 __le32 id; 933 u8 addr1[ETH_ALEN]; 934 u8 addr2[ETH_ALEN]; 935} __packed; 936 937struct cmd_ds_fwt_access { 938 struct cmd_header hdr; 939 940 __le16 action; 941 __le32 id; 942 u8 valid; 943 u8 da[ETH_ALEN]; 944 u8 dir; 945 u8 ra[ETH_ALEN]; 946 __le32 ssn; 947 __le32 dsn; 948 __le32 metric; 949 u8 rate; 950 u8 hopcount; 951 u8 ttl; 952 __le32 expiration; 953 u8 sleepmode; 954 __le32 snr; 955 __le32 references; 956 u8 prec[ETH_ALEN]; 957} __packed; 958 959struct cmd_ds_mesh_config { 960 struct cmd_header hdr; 961 962 __le16 action; 963 __le16 channel; 964 __le16 type; 965 __le16 length; 966 u8 data[128]; /* last position reserved */ 967} __packed; 968 969struct cmd_ds_mesh_access { 970 struct cmd_header hdr; 971 972 __le16 action; 973 __le32 data[32]; /* last position reserved */ 974} __packed; 975 976/* Number of stats counters returned by the firmware */ 977#define MESH_STATS_NUM 8 978#endif 979