1/*
2	usa28msg.h
3
4	Copyright (C) 1998-2000 InnoSys Incorporated.  All Rights Reserved
5	This file is available under a BSD-style copyright
6
7	Keyspan USB Async Message Formats for the USA26X
8
9	Redistribution and use in source and binary forms, with or without
10	modification, are permitted provided that the following conditions are
11	met:
12
13	1. Redistributions of source code must retain this licence text
14   	without modification, this list of conditions, and the following
15   	disclaimer.  The following copyright notice must appear immediately at
16   	the beginning of all source files:
17
18        	Copyright (C) 1998-2000 InnoSys Incorporated.  All Rights Reserved
19
20        	This file is available under a BSD-style copyright
21
22	2. The name of InnoSys Incorporated may not be used to endorse or promote
23   	products derived from this software without specific prior written
24   	permission.
25
26	THIS SOFTWARE IS PROVIDED BY INNOSYS CORP. ``AS IS'' AND ANY EXPRESS OR
27	IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
28	OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
29	NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
30	INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
31	(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
32	SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
33	CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
34	LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
35	OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
36	SUCH DAMAGE.
37
38	Note: these message formats are common to USA18, USA19, and USA28;
39	(for USA28X, see usa26msg.h)
40
41	Buffer formats for RX/TX data messages are not defined by
42	a structure, but are described here:
43
44	USB OUT (host -> USA28, transmit) messages contain a
45	REQUEST_ACK indicator (set to 0xff to request an ACK at the
46	completion of transmit; 0x00 otherwise), followed by data.
47	If the port is configured for parity, the data will be an
48	alternating string of parity and data bytes, so the message
49	format will be:
50
51		RQSTACK PAR DAT PAR DAT ...
52
53	so the maximum length is 63 bytes (1 + 62, or 31 data bytes);
54	always an odd number for the total message length.
55
56	If there is no parity, the format is simply:
57
58		RQSTACK DAT DAT DAT ...
59
60	with a total data length of 63.
61
62	USB IN (USA28 -> host, receive) messages contain data and parity
63	if parity is configred, thusly:
64
65		DAT PAR DAT PAR DAT PAR ...
66
67	for a total of 32 data bytes;
68
69	If parity is not configured, the format is:
70
71		DAT DAT DAT ...
72
73	for a total of 64 data bytes.
74
75	In the TX messages (USB OUT), the 0x01 bit of the PARity byte is
76	the parity bit.  In the RX messages (USB IN), the PARity byte is
77	the content of the 8051's status register; the parity bit
78	(RX_PARITY_BIT) is the 0x04 bit.
79
80	revision history:
81
82	1999may06	add resetDataToggle to control message
83	2000mar21	add rs232invalid to status response message
84	2000apr04	add 230.4Kb definition to setBaudRate
85	2000apr13	add/remove loopbackMode switch
86	2000apr13	change definition of setBaudRate to cover 115.2Kb, too
87	2000jun01	add extended BSD-style copyright text
88*/
89
90#ifndef	__USA28MSG__
91#define	__USA28MSG__
92
93
94struct keyspan_usa28_portControlMessage
95{
96	/*
97		there are four types of "commands" sent in the control message:
98
99		1.	configuration changes which must be requested by setting
100			the corresponding "set" flag (and should only be requested
101			when necessary, to reduce overhead on the USA28):
102	*/
103	u8	setBaudRate,	// 0=don't set, 1=baudLo/Hi, 2=115.2K, 3=230.4K
104		baudLo,			// host does baud divisor calculation
105		baudHi;			// baudHi is only used for first port (gives lower rates)
106
107	/*
108		2.	configuration changes which are done every time (because it's
109			hardly more trouble to do them than to check whether to do them):
110	*/
111	u8	parity,			// 1=use parity, 0=don't
112		ctsFlowControl,	        // all except 19Q: 1=use CTS flow control, 0=don't
113					// 19Q: 0x08:CTSflowControl 0x10:DSRflowControl
114		xonFlowControl,	// 1=use XON/XOFF flow control, 0=don't
115		rts,			// 1=on, 0=off
116		dtr;			// 1=on, 0=off
117
118	/*
119		3.	configuration data which is simply used as is (no overhead,
120			but must be correct in every host message).
121	*/
122	u8	forwardingLength,  // forward when this number of chars available
123		forwardMs,		// forward this many ms after last rx data
124		breakThreshold,	// specified in ms, 1-255 (see note below)
125		xonChar,		// specified in current character format
126		xoffChar;		// specified in current character format
127
128	/*
129		4.	commands which are flags only; these are processed in order
130			(so that, e.g., if both _txOn and _txOff flags are set, the
131			port ends in a TX_OFF state); any non-zero value is respected
132	*/
133	u8	_txOn,			// enable transmitting (and continue if there's data)
134		_txOff,			// stop transmitting
135		txFlush,		// toss outbound data
136		txForceXoff,	// pretend we've received XOFF
137		txBreak,		// turn on break (leave on until txOn clears it)
138		rxOn,			// turn on receiver
139		rxOff,			// turn off receiver
140		rxFlush,		// toss inbound data
141		rxForward,		// forward all inbound data, NOW
142		returnStatus,	// return current status n times (1 or 2)
143		resetDataToggle;// reset data toggle state to DATA0
144
145};
146
147struct keyspan_usa28_portStatusMessage
148{
149	u8	port,			// 0=first, 1=second, 2=global (see below)
150		cts,
151		dsr,			// (not used in all products)
152		dcd,
153
154		ri,				// (not used in all products)
155		_txOff,			// port has been disabled (by host)
156		_txXoff,		// port is in XOFF state (either host or RX XOFF)
157		dataLost,		// count of lost chars; wraps; not guaranteed exact
158
159		rxEnabled,		// as configured by rxOn/rxOff 1=on, 0=off
160		rxBreak,		// 1=we're in break state
161		rs232invalid,	// 1=no valid signals on rs-232 inputs
162		controlResponse;// 1=a control messages has been processed
163};
164
165// bit defines in txState
166#define	TX_OFF			0x01	// requested by host txOff command
167#define	TX_XOFF			0x02	// either real, or simulated by host
168
169struct keyspan_usa28_globalControlMessage
170{
171	u8	sendGlobalStatus,	// 2=request for two status responses
172		resetStatusToggle,	// 1=reset global status toggle
173		resetStatusCount;	// a cycling value
174};
175
176struct keyspan_usa28_globalStatusMessage
177{
178	u8	port,				// 3
179		sendGlobalStatus,	// from request, decremented
180		resetStatusCount;	// as in request
181};
182
183struct keyspan_usa28_globalDebugMessage
184{
185	u8	port,				// 2
186		n,					// typically a count/status byte
187		b;					// typically a data byte
188};
189
190// ie: the maximum length of an EZUSB endpoint buffer
191#define	MAX_DATA_LEN			64
192
193// the parity bytes have only one significant bit
194#define	RX_PARITY_BIT			0x04
195#define	TX_PARITY_BIT			0x01
196
197// update status approx. 60 times a second (16.6666 ms)
198#define	STATUS_UPDATE_INTERVAL	16
199
200#endif
201
202