1/* 2 * Blackfin On-Chip Real Time Clock Driver 3 * Supports BF51x/BF52x/BF53[123]/BF53[467]/BF54x 4 * 5 * Copyright 2004-2010 Analog Devices Inc. 6 * 7 * Enter bugs at http://blackfin.uclinux.org/ 8 * 9 * Licensed under the GPL-2 or later. 10 */ 11 12/* The biggest issue we deal with in this driver is that register writes are 13 * synced to the RTC frequency of 1Hz. So if you write to a register and 14 * attempt to write again before the first write has completed, the new write 15 * is simply discarded. This can easily be troublesome if userspace disables 16 * one event (say periodic) and then right after enables an event (say alarm). 17 * Since all events are maintained in the same interrupt mask register, if 18 * we wrote to it to disable the first event and then wrote to it again to 19 * enable the second event, that second event would not be enabled as the 20 * write would be discarded and things quickly fall apart. 21 * 22 * To keep this delay from significantly degrading performance (we, in theory, 23 * would have to sleep for up to 1 second every time we wanted to write a 24 * register), we only check the write pending status before we start to issue 25 * a new write. We bank on the idea that it doesn't matter when the sync 26 * happens so long as we don't attempt another write before it does. The only 27 * time userspace would take this penalty is when they try and do multiple 28 * operations right after another ... but in this case, they need to take the 29 * sync penalty, so we should be OK. 30 * 31 * Also note that the RTC_ISTAT register does not suffer this penalty; its 32 * writes to clear status registers complete immediately. 33 */ 34 35/* It may seem odd that there is no SWCNT code in here (which would be exposed 36 * via the periodic interrupt event, or PIE). Since the Blackfin RTC peripheral 37 * runs in units of seconds (N/HZ) but the Linux framework runs in units of HZ 38 * (2^N HZ), there is no point in keeping code that only provides 1 HZ PIEs. 39 * The same exact behavior can be accomplished by using the update interrupt 40 * event (UIE). Maybe down the line the RTC peripheral will suck less in which 41 * case we can re-introduce PIE support. 42 */ 43 44#include <linux/bcd.h> 45#include <linux/completion.h> 46#include <linux/delay.h> 47#include <linux/init.h> 48#include <linux/interrupt.h> 49#include <linux/kernel.h> 50#include <linux/module.h> 51#include <linux/platform_device.h> 52#include <linux/rtc.h> 53#include <linux/seq_file.h> 54#include <linux/slab.h> 55 56#include <asm/blackfin.h> 57 58#define dev_dbg_stamp(dev) dev_dbg(dev, "%s:%i: here i am\n", __func__, __LINE__) 59 60struct bfin_rtc { 61 struct rtc_device *rtc_dev; 62 struct rtc_time rtc_alarm; 63 u16 rtc_wrote_regs; 64}; 65 66/* Bit values for the ISTAT / ICTL registers */ 67#define RTC_ISTAT_WRITE_COMPLETE 0x8000 68#define RTC_ISTAT_WRITE_PENDING 0x4000 69#define RTC_ISTAT_ALARM_DAY 0x0040 70#define RTC_ISTAT_24HR 0x0020 71#define RTC_ISTAT_HOUR 0x0010 72#define RTC_ISTAT_MIN 0x0008 73#define RTC_ISTAT_SEC 0x0004 74#define RTC_ISTAT_ALARM 0x0002 75#define RTC_ISTAT_STOPWATCH 0x0001 76 77/* Shift values for RTC_STAT register */ 78#define DAY_BITS_OFF 17 79#define HOUR_BITS_OFF 12 80#define MIN_BITS_OFF 6 81#define SEC_BITS_OFF 0 82 83/* Some helper functions to convert between the common RTC notion of time 84 * and the internal Blackfin notion that is encoded in 32bits. 85 */ 86static inline u32 rtc_time_to_bfin(unsigned long now) 87{ 88 u32 sec = (now % 60); 89 u32 min = (now % (60 * 60)) / 60; 90 u32 hour = (now % (60 * 60 * 24)) / (60 * 60); 91 u32 days = (now / (60 * 60 * 24)); 92 return (sec << SEC_BITS_OFF) + 93 (min << MIN_BITS_OFF) + 94 (hour << HOUR_BITS_OFF) + 95 (days << DAY_BITS_OFF); 96} 97static inline unsigned long rtc_bfin_to_time(u32 rtc_bfin) 98{ 99 return (((rtc_bfin >> SEC_BITS_OFF) & 0x003F)) + 100 (((rtc_bfin >> MIN_BITS_OFF) & 0x003F) * 60) + 101 (((rtc_bfin >> HOUR_BITS_OFF) & 0x001F) * 60 * 60) + 102 (((rtc_bfin >> DAY_BITS_OFF) & 0x7FFF) * 60 * 60 * 24); 103} 104static inline void rtc_bfin_to_tm(u32 rtc_bfin, struct rtc_time *tm) 105{ 106 rtc_time_to_tm(rtc_bfin_to_time(rtc_bfin), tm); 107} 108 109/** 110 * bfin_rtc_sync_pending - make sure pending writes have complete 111 * 112 * Wait for the previous write to a RTC register to complete. 113 * Unfortunately, we can't sleep here as that introduces a race condition when 114 * turning on interrupt events. Consider this: 115 * - process sets alarm 116 * - process enables alarm 117 * - process sleeps while waiting for rtc write to sync 118 * - interrupt fires while process is sleeping 119 * - interrupt acks the event by writing to ISTAT 120 * - interrupt sets the WRITE PENDING bit 121 * - interrupt handler finishes 122 * - process wakes up, sees WRITE PENDING bit set, goes to sleep 123 * - interrupt fires while process is sleeping 124 * If anyone can point out the obvious solution here, i'm listening :). This 125 * shouldn't be an issue on an SMP or preempt system as this function should 126 * only be called with the rtc lock held. 127 * 128 * Other options: 129 * - disable PREN so the sync happens at 32.768kHZ ... but this changes the 130 * inc rate for all RTC registers from 1HZ to 32.768kHZ ... 131 * - use the write complete IRQ 132 */ 133/* 134static void bfin_rtc_sync_pending_polled(void) 135{ 136 while (!(bfin_read_RTC_ISTAT() & RTC_ISTAT_WRITE_COMPLETE)) 137 if (!(bfin_read_RTC_ISTAT() & RTC_ISTAT_WRITE_PENDING)) 138 break; 139 bfin_write_RTC_ISTAT(RTC_ISTAT_WRITE_COMPLETE); 140} 141*/ 142static DECLARE_COMPLETION(bfin_write_complete); 143static void bfin_rtc_sync_pending(struct device *dev) 144{ 145 dev_dbg_stamp(dev); 146 while (bfin_read_RTC_ISTAT() & RTC_ISTAT_WRITE_PENDING) 147 wait_for_completion_timeout(&bfin_write_complete, HZ * 5); 148 dev_dbg_stamp(dev); 149} 150 151/** 152 * bfin_rtc_reset - set RTC to sane/known state 153 * 154 * Initialize the RTC. Enable pre-scaler to scale RTC clock 155 * to 1Hz and clear interrupt/status registers. 156 */ 157static void bfin_rtc_reset(struct device *dev, u16 rtc_ictl) 158{ 159 struct bfin_rtc *rtc = dev_get_drvdata(dev); 160 dev_dbg_stamp(dev); 161 bfin_rtc_sync_pending(dev); 162 bfin_write_RTC_PREN(0x1); 163 bfin_write_RTC_ICTL(rtc_ictl); 164 bfin_write_RTC_ALARM(0); 165 bfin_write_RTC_ISTAT(0xFFFF); 166 rtc->rtc_wrote_regs = 0; 167} 168 169/** 170 * bfin_rtc_interrupt - handle interrupt from RTC 171 * 172 * Since we handle all RTC events here, we have to make sure the requested 173 * interrupt is enabled (in RTC_ICTL) as the event status register (RTC_ISTAT) 174 * always gets updated regardless of the interrupt being enabled. So when one 175 * even we care about (e.g. stopwatch) goes off, we don't want to turn around 176 * and say that other events have happened as well (e.g. second). We do not 177 * have to worry about pending writes to the RTC_ICTL register as interrupts 178 * only fire if they are enabled in the RTC_ICTL register. 179 */ 180static irqreturn_t bfin_rtc_interrupt(int irq, void *dev_id) 181{ 182 struct device *dev = dev_id; 183 struct bfin_rtc *rtc = dev_get_drvdata(dev); 184 unsigned long events = 0; 185 bool write_complete = false; 186 u16 rtc_istat, rtc_istat_clear, rtc_ictl, bits; 187 188 dev_dbg_stamp(dev); 189 190 rtc_istat = bfin_read_RTC_ISTAT(); 191 rtc_ictl = bfin_read_RTC_ICTL(); 192 rtc_istat_clear = 0; 193 194 bits = RTC_ISTAT_WRITE_COMPLETE; 195 if (rtc_istat & bits) { 196 rtc_istat_clear |= bits; 197 write_complete = true; 198 complete(&bfin_write_complete); 199 } 200 201 bits = (RTC_ISTAT_ALARM | RTC_ISTAT_ALARM_DAY); 202 if (rtc_ictl & bits) { 203 if (rtc_istat & bits) { 204 rtc_istat_clear |= bits; 205 events |= RTC_AF | RTC_IRQF; 206 } 207 } 208 209 bits = RTC_ISTAT_SEC; 210 if (rtc_ictl & bits) { 211 if (rtc_istat & bits) { 212 rtc_istat_clear |= bits; 213 events |= RTC_UF | RTC_IRQF; 214 } 215 } 216 217 if (events) 218 rtc_update_irq(rtc->rtc_dev, 1, events); 219 220 if (write_complete || events) { 221 bfin_write_RTC_ISTAT(rtc_istat_clear); 222 return IRQ_HANDLED; 223 } else 224 return IRQ_NONE; 225} 226 227static void bfin_rtc_int_set(u16 rtc_int) 228{ 229 bfin_write_RTC_ISTAT(rtc_int); 230 bfin_write_RTC_ICTL(bfin_read_RTC_ICTL() | rtc_int); 231} 232static void bfin_rtc_int_clear(u16 rtc_int) 233{ 234 bfin_write_RTC_ICTL(bfin_read_RTC_ICTL() & rtc_int); 235} 236static void bfin_rtc_int_set_alarm(struct bfin_rtc *rtc) 237{ 238 /* Blackfin has different bits for whether the alarm is 239 * more than 24 hours away. 240 */ 241 bfin_rtc_int_set(rtc->rtc_alarm.tm_yday == -1 ? RTC_ISTAT_ALARM : RTC_ISTAT_ALARM_DAY); 242} 243 244static int bfin_rtc_alarm_irq_enable(struct device *dev, unsigned int enabled) 245{ 246 struct bfin_rtc *rtc = dev_get_drvdata(dev); 247 248 dev_dbg_stamp(dev); 249 if (enabled) 250 bfin_rtc_int_set_alarm(rtc); 251 else 252 bfin_rtc_int_clear(~(RTC_ISTAT_ALARM | RTC_ISTAT_ALARM_DAY)); 253 254 return 0; 255} 256 257static int bfin_rtc_read_time(struct device *dev, struct rtc_time *tm) 258{ 259 struct bfin_rtc *rtc = dev_get_drvdata(dev); 260 261 dev_dbg_stamp(dev); 262 263 if (rtc->rtc_wrote_regs & 0x1) 264 bfin_rtc_sync_pending(dev); 265 266 rtc_bfin_to_tm(bfin_read_RTC_STAT(), tm); 267 268 return 0; 269} 270 271static int bfin_rtc_set_time(struct device *dev, struct rtc_time *tm) 272{ 273 struct bfin_rtc *rtc = dev_get_drvdata(dev); 274 int ret; 275 unsigned long now; 276 277 dev_dbg_stamp(dev); 278 279 ret = rtc_tm_to_time(tm, &now); 280 if (ret == 0) { 281 if (rtc->rtc_wrote_regs & 0x1) 282 bfin_rtc_sync_pending(dev); 283 bfin_write_RTC_STAT(rtc_time_to_bfin(now)); 284 rtc->rtc_wrote_regs = 0x1; 285 } 286 287 return ret; 288} 289 290static int bfin_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alrm) 291{ 292 struct bfin_rtc *rtc = dev_get_drvdata(dev); 293 dev_dbg_stamp(dev); 294 alrm->time = rtc->rtc_alarm; 295 bfin_rtc_sync_pending(dev); 296 alrm->enabled = !!(bfin_read_RTC_ICTL() & (RTC_ISTAT_ALARM | RTC_ISTAT_ALARM_DAY)); 297 return 0; 298} 299 300static int bfin_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alrm) 301{ 302 struct bfin_rtc *rtc = dev_get_drvdata(dev); 303 unsigned long rtc_alarm; 304 305 dev_dbg_stamp(dev); 306 307 if (rtc_tm_to_time(&alrm->time, &rtc_alarm)) 308 return -EINVAL; 309 310 rtc->rtc_alarm = alrm->time; 311 312 bfin_rtc_sync_pending(dev); 313 bfin_write_RTC_ALARM(rtc_time_to_bfin(rtc_alarm)); 314 if (alrm->enabled) 315 bfin_rtc_int_set_alarm(rtc); 316 317 return 0; 318} 319 320static int bfin_rtc_proc(struct device *dev, struct seq_file *seq) 321{ 322#define yesno(x) ((x) ? "yes" : "no") 323 u16 ictl = bfin_read_RTC_ICTL(); 324 dev_dbg_stamp(dev); 325 seq_printf(seq, 326 "alarm_IRQ\t: %s\n" 327 "wkalarm_IRQ\t: %s\n" 328 "seconds_IRQ\t: %s\n", 329 yesno(ictl & RTC_ISTAT_ALARM), 330 yesno(ictl & RTC_ISTAT_ALARM_DAY), 331 yesno(ictl & RTC_ISTAT_SEC)); 332 return 0; 333#undef yesno 334} 335 336static struct rtc_class_ops bfin_rtc_ops = { 337 .read_time = bfin_rtc_read_time, 338 .set_time = bfin_rtc_set_time, 339 .read_alarm = bfin_rtc_read_alarm, 340 .set_alarm = bfin_rtc_set_alarm, 341 .proc = bfin_rtc_proc, 342 .alarm_irq_enable = bfin_rtc_alarm_irq_enable, 343}; 344 345static int __devinit bfin_rtc_probe(struct platform_device *pdev) 346{ 347 struct bfin_rtc *rtc; 348 struct device *dev = &pdev->dev; 349 int ret = 0; 350 unsigned long timeout = jiffies + HZ; 351 352 dev_dbg_stamp(dev); 353 354 /* Allocate memory for our RTC struct */ 355 rtc = kzalloc(sizeof(*rtc), GFP_KERNEL); 356 if (unlikely(!rtc)) 357 return -ENOMEM; 358 platform_set_drvdata(pdev, rtc); 359 device_init_wakeup(dev, 1); 360 361 /* Register our RTC with the RTC framework */ 362 rtc->rtc_dev = rtc_device_register(pdev->name, dev, &bfin_rtc_ops, 363 THIS_MODULE); 364 if (unlikely(IS_ERR(rtc->rtc_dev))) { 365 ret = PTR_ERR(rtc->rtc_dev); 366 goto err; 367 } 368 369 /* Grab the IRQ and init the hardware */ 370 ret = request_irq(IRQ_RTC, bfin_rtc_interrupt, 0, pdev->name, dev); 371 if (unlikely(ret)) 372 goto err_reg; 373 /* sometimes the bootloader touched things, but the write complete was not 374 * enabled, so let's just do a quick timeout here since the IRQ will not fire ... 375 */ 376 while (bfin_read_RTC_ISTAT() & RTC_ISTAT_WRITE_PENDING) 377 if (time_after(jiffies, timeout)) 378 break; 379 bfin_rtc_reset(dev, RTC_ISTAT_WRITE_COMPLETE); 380 bfin_write_RTC_SWCNT(0); 381 382 return 0; 383 384err_reg: 385 rtc_device_unregister(rtc->rtc_dev); 386err: 387 kfree(rtc); 388 return ret; 389} 390 391static int __devexit bfin_rtc_remove(struct platform_device *pdev) 392{ 393 struct bfin_rtc *rtc = platform_get_drvdata(pdev); 394 struct device *dev = &pdev->dev; 395 396 bfin_rtc_reset(dev, 0); 397 free_irq(IRQ_RTC, dev); 398 rtc_device_unregister(rtc->rtc_dev); 399 platform_set_drvdata(pdev, NULL); 400 kfree(rtc); 401 402 return 0; 403} 404 405#ifdef CONFIG_PM 406static int bfin_rtc_suspend(struct platform_device *pdev, pm_message_t state) 407{ 408 struct device *dev = &pdev->dev; 409 410 dev_dbg_stamp(dev); 411 412 if (device_may_wakeup(dev)) { 413 enable_irq_wake(IRQ_RTC); 414 bfin_rtc_sync_pending(dev); 415 } else 416 bfin_rtc_int_clear(0); 417 418 return 0; 419} 420 421static int bfin_rtc_resume(struct platform_device *pdev) 422{ 423 struct device *dev = &pdev->dev; 424 425 dev_dbg_stamp(dev); 426 427 if (device_may_wakeup(dev)) 428 disable_irq_wake(IRQ_RTC); 429 430 /* 431 * Since only some of the RTC bits are maintained externally in the 432 * Vbat domain, we need to wait for the RTC MMRs to be synced into 433 * the core after waking up. This happens every RTC 1HZ. Once that 434 * has happened, we can go ahead and re-enable the important write 435 * complete interrupt event. 436 */ 437 while (!(bfin_read_RTC_ISTAT() & RTC_ISTAT_SEC)) 438 continue; 439 bfin_rtc_int_set(RTC_ISTAT_WRITE_COMPLETE); 440 441 return 0; 442} 443#else 444# define bfin_rtc_suspend NULL 445# define bfin_rtc_resume NULL 446#endif 447 448static struct platform_driver bfin_rtc_driver = { 449 .driver = { 450 .name = "rtc-bfin", 451 .owner = THIS_MODULE, 452 }, 453 .probe = bfin_rtc_probe, 454 .remove = __devexit_p(bfin_rtc_remove), 455 .suspend = bfin_rtc_suspend, 456 .resume = bfin_rtc_resume, 457}; 458 459module_platform_driver(bfin_rtc_driver); 460 461MODULE_DESCRIPTION("Blackfin On-Chip Real Time Clock Driver"); 462MODULE_AUTHOR("Mike Frysinger <vapier@gentoo.org>"); 463MODULE_LICENSE("GPL"); 464MODULE_ALIAS("platform:rtc-bfin"); 465