| 98619dcb77d9dcbed67e39a71e4357fc99dc0f25 |
|
29-Dec-2011 |
Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> |
ARM: at91: enable on flash bbt for Atmel Reference and DT boards
Enable it on Calao board too as they are in DT too.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
| bf4289cba02b8cf770ecd7959ca70839f0dd9d3c |
|
29-Dec-2011 |
Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> |
ATMEL: fix nand ecc support
So we can now choose for the board the ecc mode (ecc soft, soft bch, no ecc
and hardware).
Set ecc mode in the boards to soft as currently in the driver.
Move platform data to a common header
include/linux/platform_data/atmel_nand.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: David Woodhouse <dwmw2@infradead.org>
|
| 63b4c2967850033de0a488d2ba7cd09052199d99 |
|
24-Nov-2011 |
Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> |
ARM: at91/boards: use -EINVAL for invalid gpio
this will allow to use gpio_is_valid
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
|
| faee0cc33c3df3b63314926eecef77d384ae9cd4 |
|
13-Oct-2011 |
Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> |
ARM: at91: make smc register base soc independent
now sam9_smc_configure will take as first parameter is the SMC id
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
| 84e0cdb0a262483a3618091c43dae33d36226430 |
|
08-Mar-2011 |
Jamie Iles <jamie@jamieiles.com> |
macb: unify at91 and avr32 platform data
Both at91 and avr32 defines its own platform data structure for
the macb driver and both share common structures though at91
includes a currently unused phy_irq_pin. Create a common
macb_platform_data for macb that both at91 and avr32 can use. In
future we can use this to support other architectures that use the
same IP block with the macb driver.
v2: rename eth_platform_data to macb_platform_data and allow at91_ether
to share the platform data with macb.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
| 1754aab9bb869c173aa03b57587256827250e488 |
|
29-May-2011 |
Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> |
mtd: ATMEL, AVR32: inline nand partition table access
Currently atmel_nand driver used by AT91 and AVR32 calls a special callback
which return nand partition table and number of partitions. However in all
boards this callback returns just static data. So drop this callback and
make atmel_nand use partition table provided statically via platform_data.
Nicolas Ferre: I am in favor for a mainline inclusion through linux-mtd tree.
Hans-Christian Egtvedt: I'm fine by sending the changes for AVR32 through linux-mtd
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
| 2f8163baada3dbd0ce891c35bc59ae46e773487a |
|
26-Jul-2011 |
Russell King <rmk+kernel@arm.linux.org.uk> |
ARM: gpio: convert includes of mach/gpio.h and asm/gpio.h to linux/gpio.h
Convert arch/arm includes of mach/gpio.h and asm/gpio.h to linux/gpio.h
before we start consolidating the individual platform implementations
of the gpio header files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| 92100c12ca1bc5f347ff41c1413f9db07c4d276c |
|
23-Apr-2011 |
Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> |
at91: factorize at91 interrupts init to soc
they are the same except the default priority
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
|
| 21d08b9d5536ac418bbce4f419fe2b528b7ddf31 |
|
23-Apr-2011 |
Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> |
at91: introduce commom AT91_BASE_SYS
On all at91 except rm9200 and x40 have the System Controller starts
at address 0xffffc000 and has a size of 16KiB.
On rm9200 it's start at 0xfffe4000 of 111KiB with non reserved data starting
at 0xfffff000
This patch removes the individual definitions of AT91_BASE_SYS and
replaces them with a common version at base 0xfffffc000 and size 16KiB
and map the same memory space
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
|
| 64393b3ae4e3cc86e2d622f682d736ec973364b6 |
|
01-Jul-2011 |
Nicolas Ferre <nicolas.ferre@atmel.com> |
AT91: Change nand buswidth logic to match hardware default configuration
The recently modified nand buswitth configuration is not aligned with
board reality: the double footprint on boards is always populated with 8bits
buswidth nand flashes.
So we have to consider that without particular configuration the 8bits
buswidth is selected by default.
Moreover, the previous logic was always using !board_have_nand_8bit(), we
change it to a simpler: board_have_nand_16bit().
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
| 3d51f259e819b49b3f88b594afcb044d1ffcda8a |
|
02-May-2011 |
Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> |
at91: drop boot_params and PLAT_PHYS_OFFSET
select ARM_PATCH_PHYS_VIRT
as with ARM_PATCH_PHYS_VIRT you can patch boot_params at runtime or any recent
bootloader will provide a valid atags pointer in r2
as point out by Russell on AT91 we never use XIP
so se do not need PLAT_PHYS_OFFSET
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
|
| 1b021a3b23a40be89c4f3fbe6f4696aa15141f26 |
|
28-Apr-2011 |
Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> |
at91: fix map_io init usage
switch early init to init_early and introduce soc map_io
with this Patch we will not do any more early device setup during the map io
tks to Russell to point the new call back
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Andrew Victor <linux@maxim.org.za>
|
| 76b2ab76a4492f8f43c511857181f8421901ce3f |
|
13-Apr-2011 |
Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> |
at91: remove MTD_NAND_ATMEL_BUSWIDTH_16 option
no board configure it as 'n' and it's an issue to merge all defconfigs
in one
On AT91SAM926x boards both types of NAND flash can be present
(8 and 16 bit data bus width).
so will pass it via system_rev
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
|
| 6451d7783ba5ff24eb1a544eaa6665b890f30466 |
|
15-Oct-2010 |
Nicolas Pitre <nicolas.pitre@linaro.org> |
arm: remove machine_desc.io_pg_offst and .phys_io
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
|
| a6e016f19d393fbe4e040bee8155b03b840fa689 |
|
21-Sep-2010 |
Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> |
AT91: at91sam9g20ek: merge 2mmc version in one board
The board-sam9g20ek-2slot-mmc.c was a revision of the at91sam9g20ek
since board revision C. It contains 2 sd/mmc slots.
This merge keep the support of the old machine ID
MACH_AT91SAM9G20EK_2MMC for backward compatibility.
Now we use the ATAG to pass the hardware functionality to kernel
with this board revision encoding
bit 0:
0 => 1 sd/mmc slot
1 => 2 sd/mmc slots connectors (board from revision C)
system_rev tested on Barebox commit d8f3ee103a9f4bd
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
| 5e886f68e5b1c0a62c64cbc3707304259ba46183 |
|
03-Jun-2010 |
Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> |
ARM: 6162/1: at91sam9g20ek: add fixed-value regulator for wm8731
If CONFIG_REGULATOR is enabled, wm8731 fails on AT91SAM9G20EK board,
since codec driver requires several voltage supplies and none are
provided currently. As requires voltages are hardwired to 3V3, use fixed
voltage regulator for this chip.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| 438ff39d7813515d3aac20f53b5b95aaa58b38f9 |
|
11-Mar-2010 |
Rob Alley <rob.alley@navmanwireless.com> |
ARM: 5986/1: at91sam9g20-ek: Correct braces in I2C registration code
The change introduced in patch 5596/1 used incorrect bracing which
resulted in the AT24 EEPROM no longer being registered. This patch
corrects the bracing and allows both the WM8731 audio device and AT24
EEPROM device to be registered.
Signed-off-by: Rob Alley <rob.alley@navmanwireless.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| 4f37940d64a155c025968118849b596f6aaa8128 |
|
10-Jul-2009 |
Samuel R. C. Vale <srcvale@holoscopio.com> |
trivial: fix typos in comments s/DGBU/DBGU/
DBGU means Debug Unit, was refered as "DGBU" in some files. Fixed to "DBGU".
Signed-off-by: Samuel R. C. Vale <srcvale@holoscopio.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
| d7dbf6ea40a2859adaca2dfdbbea83f3d6c73c2f |
|
08-Jul-2009 |
Mark Brown <broonie@sirena.org.uk> |
[ARM] 5596/1: at91sam9g20-ek: Register WM8731 in board file
The WM8731 driver has been updated to allow registration via normal
device model methods rather than from within the ASoC driver probe
so update the AT91SAM9G20-EK to make use of this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| 59c5fe6d848cae8fd51498d17532f5aad3866f98 |
|
29-Jun-2009 |
Nicolas Ferre <nicolas.ferre@atmel.com> |
[ARM] 5562/2: at91: add gpio button support for at91sam9g20ek
This adds input keyboard gpio support on at91sam9g20ek board.
It adds button 3 and 4.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| 6953e47e11ea85c8c91ac49a5c779e0a4a143e47 |
|
25-May-2009 |
Dmitry Baryshkov <dbaryshkov@gmail.com> |
[ARM] 5524/1: at91sam9g20ek: add i2c eeprom info
Add board information about on-board I2C eeprom AT24C512N at 0x50.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| 423145a5d4def58cff760809d48cfb21316d59a9 |
|
16-Feb-2009 |
Mark Brown <broonie@sirena.org.uk> |
[ARM] 5399/1: [AT91] Configure MCLK and SSC for AT91SAMG20-EK
The AT91SAM20-EK has a WM8731 attached to it with MCLK supplied from
PCLK0 and the digital audio interface supplied by SSC0.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| 8cdae51aa951e22bc9134cc94c30d1206c84ea8e |
|
06-Oct-2008 |
Andrew Victor <linux@maxim.org.za> |
[ARM] 5289/1: [AT91] Convert boards to use sam9_smc_configure()
Convert the SAM9 and CAP9 board-specific files to make use of the
sam9_smc_configure() method to configure the memory-controller for
external peripherals.
The following boards have been modified:
cam60 : NAND
cap9adk : NAND, NOR
qil-a9260 : NAND
sam9-l9260 : NAND
sam9260ek : NAND
sam9261ek : DM9000 Ethernet, NAND
sam9263 : NAND
sam9g20ek : NAND
sam9rlek : NAND
usb-a9260 : NAND
usb-a9263 .: NAND
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| e505240b6a6fd47b84cfeb1272ffeacd3e0874b3 |
|
21-Sep-2008 |
Andrew Victor <linux@maxim.org.za> |
[ARM] 5257/2: [AT91] Use SZ_ definitions and MTDPART_OFS_NXTBLK instead of hex-values
In the various AT91 board files, replace hard-coded size values (eg,
0x800000) with the SZ_ size definitions (eg, SZ_8M) from sizes.h
Also replace MTD partition offsets with MTDPART_OFS_NXTBLK.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| a09e64fbc0094e3073dbb09c3b4bfe4ab669244b |
|
05-Aug-2008 |
Russell King <rmk@dyn-67.arm.linux.org.uk> |
[ARM] Move include/asm-arm/arch-* to arch/arm/*/include/mach
This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| be509729356b7433f73df2b9a966674a437fbbc1 |
|
04-Aug-2008 |
Russell King <rmk@dyn-67.arm.linux.org.uk> |
[ARM] Remove asm/hardware.h, use asm/arch/hardware.h instead
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| f6ed6f78d46b43b6d908b39ed3322f7cda23f4a8 |
|
01-Aug-2008 |
Pieter du Preez <pdupreez@gmail.com> |
Fix rename of at91_nand -> atmel_nand
Structs called at91_nand_data where renamed to atmel_nand_data
and configs called *MTD_NAND_AT91* where renamed to
*MTD_NAND_ATMEL*. This was unfortunately not done consistently,
causing NAND chips not being initialised on several ARM boards.
I am aware that the author of the original change did not rename
MTD_NAND_AT91_BUSWIDTH to MTD_NAND_ATMEL_BUSWIDTH, for example.
All *MTD_NAND_AT91* where renamed to *MTD_NAND_ATMEL* in order
to keep naming consistency.
This patch was only tested on a MACH_SAM9_L9260, as this is the
only ARM board I have to my disposal.
Before this patch:
$ git-ls-files |xargs grep atmel_nand |wc -l
105
$ git-ls-files |xargs grep at91_nand |wc -l
4
$ git-ls-files |xargs grep MTD_NAND_ATMEL |wc -l
8
$ git-ls-files |xargs grep MTD_NAND_AT91 |wc -l
47
After this patch:
$ git-ls-files |xargs grep atmel_nand |wc -l
109
$ git-ls-files |xargs grep at91_nand |wc -l
0
$ git-ls-files |xargs grep MTD_NAND_ATMEL |wc -l
55
$ git-ls-files |xargs grep MTD_NAND_AT91 |wc -l
0
Signed-off-by: Pieter du Preez <pdupreez@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
|
| 7c896834735f497cc405068d16a51717f993af7f |
|
28-Jul-2008 |
Haavard Skinnemoen <haavard.skinnemoen@atmel.com> |
[ARM] 5180/1: at91: Fix at91_nand -> atmel_nand rename fallout
struct at91_nand has been renamed atmel_nand. Fix the four boards that
were added since the patch was created.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| 613526677a74c2b3d1b1696ea7334b2cf35155b3 |
|
10-Jul-2008 |
sedji gaouaou <sedji.gaouaou@atmel.com> |
[ARM] 5130/4: Support for the at91sam9g20
Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock
speed.
We created a new board for this device but based the chip support
directly on 9260 files with little updates.
Here is the chip page on Atmel wabsite:
http://atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|