| ab9c17a009ee8eb8c667f22dc0be0709effceab9 |
|
13-Dec-2011 |
Jack Morgenstein <jackm@dev.mellanox.co.il> |
mlx4_core: Modify driver initialization flow to accommodate SRIOV for Ethernet
1. Added module parameters sr_iov and probe_vf for controlling enablement of
SRIOV mode.
2. Increased default max num-qps, num-mpts and log_num_macs to accomodate
SRIOV mode
3. Added port_type_array as a module parameter to allow driver startup with
ports configured as desired.
In SRIOV mode, only ETH is supported, and this array is ignored; otherwise,
for the case where the FW supports both port types (ETH and IB), the
port_type_array parameter is used.
By default, the port_type_array is set to configure both ports as IB.
4. When running in sriov mode, the master needs to initialize the ICM eq table
to hold the eq's for itself and also for all the slaves.
5. mlx4_set_port_mask() now invoked from mlx4_init_hca, instead of in mlx4_dev_cap.
6. Introduced sriov VF (slave) device startup/teardown logic (mainly procedures
mlx4_init_slave, mlx4_slave_exit, mlx4_slave_cap, mlx4_slave_exit and flow
modifications in __mlx4_init_one, mlx4_init_hca, and mlx4_setup_hca).
VFs obtain their startup information from the PF (master) device via the
comm channel.
7. In SRIOV mode (both PF and VF), MSI_X must be enabled, or the driver
aborts loading the device.
8. Do not allow setting port type via sysfs when running in SRIOV mode.
9. mlx4_get_ownership: Currently, only one PF is supported by the driver.
If the HCA is burned with FW which enables more than one PF, only one
of the PFs is allowed to run. The first one up grabs a FW ownership
semaphone -- all other PFs will find that semaphore taken, and the
driver will not allow them to run.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Liran Liss <liranl@mellanox.co.il>
Signed-off-by: Marcel Apfelbaum <marcela@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
/include/linux/mlx4/cmd.h
|
| f9baff509f8a05a79626defdbdf4f4aa4efd373b |
|
13-Dec-2011 |
Jack Morgenstein <jackm@dev.mellanox.co.il> |
mlx4_core: Add "native" argument to mlx4_cmd and its callers (where needed)
For SRIOV, some Hypervisor commands can be executed directly (native = 1).
Others should go through the command wrapper flow (for tracking resource
usage, for example, or for changing some HCA configurations that slaves
need to be notified of).
This patch sets the groundwork for this capability -- adding the correct
value of "native" in each case.
Note that if SRIOV is not activated, this parameter has no effect.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
/include/linux/mlx4/cmd.h
|
| 623ed84b1f9553bc962c2aca92f488aa6f27ecd1 |
|
13-Dec-2011 |
Jack Morgenstein <jackm@dev.mellanox.co.il> |
mlx4_core: initial header-file changes for SRIOV support
These changes will not affect module operation as yet. They
are only to get some structs and enums in place for use by
subsequent patches (making those smaller).
Added here:
* sriov state structs and inlines (mlx4_is_master/slave/mfunc)
* comm-channel and vhcr support structures
* enum values for new FW and comm-channel virtual commands
(i.e., commands, passed via the comm channel to the PF-driver).
* prototypes for many command wrapper functions (used by the
PF context for processing FW commands passed to it by the VFs).
* struct mlx4_eqe is moved from eq.c to mlx4.h (it will be used
by other mlx4_core source files).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
/include/linux/mlx4/cmd.h
|
| f2a3f6a32cf64db1495b5ced8625b9a80bde44e5 |
|
15-Jun-2011 |
Or Gerlitz <ogerlitz@mellanox.com> |
mlx4_core: Add network flow counters
ConnectX devices support a set of flow counters that can be attached
to a set containing one or more QPs. Each such counter tracks receive
and transmit packets and bytes of these QPs. This patch queries the
device to check support for counters, handles initialization of the
HCA to enable counters, and initializes a bitmap allocator to control
counter allocations. Derived from patch by Eli Cohen <eli@mellanox.co.il>.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
/include/linux/mlx4/cmd.h
|
| 9e5fca251f44832cb996961048ea977f80faf6ea |
|
27-Oct-2010 |
Linus Torvalds <torvalds@linux-foundation.org> |
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (63 commits)
IB/qib: clean up properly if pci_set_consistent_dma_mask() fails
IB/qib: Allow driver to load if PCIe AER fails
IB/qib: Fix uninitialized pointer if CONFIG_PCI_MSI not set
IB/qib: Fix extra log level in qib_early_err()
RDMA/cxgb4: Remove unnecessary KERN_<level> use
RDMA/cxgb3: Remove unnecessary KERN_<level> use
IB/core: Add link layer type information to sysfs
IB/mlx4: Add VLAN support for IBoE
IB/core: Add VLAN support for IBoE
IB/mlx4: Add support for IBoE
mlx4_en: Change multicast promiscuous mode to support IBoE
mlx4_core: Update data structures and constants for IBoE
mlx4_core: Allow protocol drivers to find corresponding interfaces
IB/uverbs: Return link layer type to userspace for query port operation
IB/srp: Sync buffer before posting send
IB/srp: Use list_first_entry()
IB/srp: Reduce number of BUSY conditions
IB/srp: Eliminate two forward declarations
IB/mlx4: Signal node desc changes to SM by using FW to generate trap 144
IB: Replace EXTRA_CFLAGS with ccflags-y
...
|
| 116e9535fe5e00bafab7a637f306b110cf95cff5 |
|
27-Oct-2010 |
Roland Dreier <rolandd@cisco.com> |
Merge branches 'amso1100', 'cma', 'cxgb3', 'cxgb4', 'ehca', 'iboe', 'ipoib', 'misc', 'mlx4', 'nes', 'qib' and 'srp' into for-next
|
| 96dfa684c85d24b697f865f37a4f0c8678fc86e9 |
|
21-Oct-2010 |
Eli Cohen <eli@mellanox.co.il> |
mlx4_core: Update data structures and constants for IBoE
Add fields to hardware data structures and add new constants required for IBoE
support.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
/include/linux/mlx4/cmd.h
|
| d0d68b8693bd16bfbbc93b89f1d9f3351723307c |
|
04-Oct-2010 |
Jack Morgenstein <jackm@dev.mellanox.co.il> |
IB/mlx4: Signal node desc changes to SM by using FW to generate trap 144
The Node Description cannot be changed via MADs (it is read-only).
Until now, it was changed in the driver via sysfs, and the new Node
Description was simply inserted by the driver into MAD responses
(replacing the description returned by FW).
System startup scripts use the sysfs interface to change the node
description at driver startup to show the hostname, etc. However, this
has a race condition: the SM could discover the original FW node
description rather than the system-specific description if it queried the
port before the startup scripts finish running.
For mlx4, we fix this with a new FW command (SET_NODE) that allows
passing the new node description to FW. When this command is invoked,
FW sends a trap 144 to the SM. When it gets this trap, the SM can
query the node to obtain the new node description -- thus eliminating
the effects of the race.
This patch simply calls SET_NODE command when a new node description
is entered via sysfs (thus causing trap 144 to be issued by the FW).
We ignore all failures of the SET_NODE command (including those caused
by using a device FW that predates the SET_NODE command), since in
that case things work just as before.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
/include/linux/mlx4/cmd.h
|
| e7c1c2c46201e46f8ce817196507d2ffd3dafd8e |
|
24-Aug-2010 |
Yevgeny Petrilin <yevgenyp@mellanox.co.il> |
mlx4_en: Added self diagnostics test implementation
The selftest includes 5 features:
1. Interrupt test: Executing commands and receiving command completion
on all our interrupt vectors.
2. Link test: Verifying we are connected to valid link partner.
3. Speed test: Check that we negotiated link speed correctly.
4. Registers test: Activate HW health check command.
5. Loopback test: Send a packet on loopback interface and catch it on RX side.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
/include/linux/mlx4/cmd.h
|
| 27bf91d6a0d5a9c7224e8687754249bba67dd4cf |
|
19-Mar-2009 |
Yevgeny Petrilin <yevgenyp@mellanox.co.il> |
mlx4_core: Add link type autosensing
When a port's link is down (except to driver restart) and the port is
configured for auto sensing, we try to sense port link type (Ethernet
or InfiniBand) in order to determine how to initialize the port. If
the port type needs to be changed, all mlx4 for the device interfaces
are unregistered and then registered again with the new port
types. Sensing is done with intervals of 3 seconds.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
/include/linux/mlx4/cmd.h
|
| 2a2336f8228292b8197f4187e54b0748903e6645 |
|
22-Oct-2008 |
Yevgeny Petrilin <yevgenyp@mellanox.co.il> |
mlx4_core: Ethernet MAC/VLAN management
Add support for managing MAC and VLAN filters for each port.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Oren Duer <oren@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
/include/linux/mlx4/cmd.h
|
| 3fdcb97f0b8d8a29117dc36acd0b15965d2a2160 |
|
17-Apr-2008 |
Eli Cohen <eli@dev.mellanox.co.il> |
IB/mlx4: Add support for modifying CQ moderation parameters
Signed-off-by: Eli Cohen <eli@mellnaox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
/include/linux/mlx4/cmd.h
|
| 5ae2a7a836be660ff1621cce1c46930f19200589 |
|
18-Jun-2007 |
Roland Dreier <rolandd@cisco.com> |
IB/mlx4: Handle FW command interface rev 3
Upcoming firmware introduces command interface revision 3, which
changes the way port capabilities are queried and set. Update the
driver to handle both the new and old command interfaces by adding a
new MLX4_FLAG_OLD_PORT_CMDS that it is set after querying the firmware
interface revision and then using the correct interface based on the
setting of the flag.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
/include/linux/mlx4/cmd.h
|
| 225c7b1feef1b41170f7037a5b10a65cd8a42c54 |
|
09-May-2007 |
Roland Dreier <rolandd@cisco.com> |
IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters
Add an InfiniBand driver for Mellanox ConnectX adapters. Because
these adapters can also be used as ethernet NICs and Fibre Channel
HBAs, the driver is split into two modules:
mlx4_core: Handles low-level things like device initialization and
processing firmware commands. Also controls resource allocation
so that the InfiniBand, ethernet and FC functions can share a
device without stepping on each other.
mlx4_ib: Handles InfiniBand-specific things; plugs into the
InfiniBand midlayer.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
/include/linux/mlx4/cmd.h
|