1/***************************************************************************/
2
3/*
4 *	sltimers.c -- generic ColdFire slice timer support.
5 *
6 *	Copyright (C) 2009-2010, Philippe De Muyter <phdm@macqel.be>
7 *	based on
8 *	timers.c -- generic ColdFire hardware timer support.
9 *	Copyright (C) 1999-2008, Greg Ungerer <gerg@snapgear.com>
10 */
11
12/***************************************************************************/
13
14#include <linux/kernel.h>
15#include <linux/init.h>
16#include <linux/sched.h>
17#include <linux/interrupt.h>
18#include <linux/irq.h>
19#include <linux/profile.h>
20#include <linux/clocksource.h>
21#include <asm/io.h>
22#include <asm/traps.h>
23#include <asm/machdep.h>
24#include <asm/coldfire.h>
25#include <asm/mcfslt.h>
26#include <asm/mcfsim.h>
27
28/***************************************************************************/
29
30#ifdef CONFIG_HIGHPROFILE
31
32/*
33 *	By default use Slice Timer 1 as the profiler clock timer.
34 */
35#define	PA(a)	(MCF_MBAR + MCFSLT_TIMER1 + (a))
36
37/*
38 *	Choose a reasonably fast profile timer. Make it an odd value to
39 *	try and get good coverage of kernel operations.
40 */
41#define	PROFILEHZ	1013
42
43irqreturn_t mcfslt_profile_tick(int irq, void *dummy)
44{
45	/* Reset Slice Timer 1 */
46	__raw_writel(MCFSLT_SSR_BE | MCFSLT_SSR_TE, PA(MCFSLT_SSR));
47	if (current->pid)
48		profile_tick(CPU_PROFILING);
49	return IRQ_HANDLED;
50}
51
52static struct irqaction mcfslt_profile_irq = {
53	.name	 = "profile timer",
54	.flags	 = IRQF_DISABLED | IRQF_TIMER,
55	.handler = mcfslt_profile_tick,
56};
57
58void mcfslt_profile_init(void)
59{
60	printk(KERN_INFO "PROFILE: lodging TIMER 1 @ %dHz as profile timer\n",
61	       PROFILEHZ);
62
63	setup_irq(MCF_IRQ_PROFILER, &mcfslt_profile_irq);
64
65	/* Set up TIMER 2 as high speed profile clock */
66	__raw_writel(MCF_BUSCLK / PROFILEHZ - 1, PA(MCFSLT_STCNT));
67	__raw_writel(MCFSLT_SCR_RUN | MCFSLT_SCR_IEN | MCFSLT_SCR_TEN,
68								PA(MCFSLT_SCR));
69
70}
71
72#endif	/* CONFIG_HIGHPROFILE */
73
74/***************************************************************************/
75
76/*
77 *	By default use Slice Timer 0 as the system clock timer.
78 */
79#define	TA(a)	(MCF_MBAR + MCFSLT_TIMER0 + (a))
80
81static u32 mcfslt_cycles_per_jiffy;
82static u32 mcfslt_cnt;
83
84static irq_handler_t timer_interrupt;
85
86static irqreturn_t mcfslt_tick(int irq, void *dummy)
87{
88	/* Reset Slice Timer 0 */
89	__raw_writel(MCFSLT_SSR_BE | MCFSLT_SSR_TE, TA(MCFSLT_SSR));
90	mcfslt_cnt += mcfslt_cycles_per_jiffy;
91	return timer_interrupt(irq, dummy);
92}
93
94static struct irqaction mcfslt_timer_irq = {
95	.name	 = "timer",
96	.flags	 = IRQF_DISABLED | IRQF_TIMER,
97	.handler = mcfslt_tick,
98};
99
100static cycle_t mcfslt_read_clk(struct clocksource *cs)
101{
102	unsigned long flags;
103	u32 cycles, scnt;
104
105	local_irq_save(flags);
106	scnt = __raw_readl(TA(MCFSLT_SCNT));
107	cycles = mcfslt_cnt;
108	if (__raw_readl(TA(MCFSLT_SSR)) & MCFSLT_SSR_TE) {
109		cycles += mcfslt_cycles_per_jiffy;
110		scnt = __raw_readl(TA(MCFSLT_SCNT));
111	}
112	local_irq_restore(flags);
113
114	/* subtract because slice timers count down */
115	return cycles + ((mcfslt_cycles_per_jiffy - 1) - scnt);
116}
117
118static struct clocksource mcfslt_clk = {
119	.name	= "slt",
120	.rating	= 250,
121	.read	= mcfslt_read_clk,
122	.mask	= CLOCKSOURCE_MASK(32),
123	.flags	= CLOCK_SOURCE_IS_CONTINUOUS,
124};
125
126void hw_timer_init(irq_handler_t handler)
127{
128	mcfslt_cycles_per_jiffy = MCF_BUSCLK / HZ;
129	/*
130	 *	The coldfire slice timer (SLT) runs from STCNT to 0 included,
131	 *	then STCNT again and so on.  It counts thus actually
132	 *	STCNT + 1 steps for 1 tick, not STCNT.  So if you want
133	 *	n cycles, initialize STCNT with n - 1.
134	 */
135	__raw_writel(mcfslt_cycles_per_jiffy - 1, TA(MCFSLT_STCNT));
136	__raw_writel(MCFSLT_SCR_RUN | MCFSLT_SCR_IEN | MCFSLT_SCR_TEN,
137								TA(MCFSLT_SCR));
138	/* initialize mcfslt_cnt knowing that slice timers count down */
139	mcfslt_cnt = mcfslt_cycles_per_jiffy;
140
141	timer_interrupt = handler;
142	setup_irq(MCF_IRQ_TIMER, &mcfslt_timer_irq);
143
144	clocksource_register_hz(&mcfslt_clk, MCF_BUSCLK);
145
146#ifdef CONFIG_HIGHPROFILE
147	mcfslt_profile_init();
148#endif
149}
150