1/* 2 * Freescale CPM1/CPM2 I2C interface. 3 * Copyright (c) 1999 Dan Malek (dmalek@jlc.net). 4 * 5 * moved into proper i2c interface; 6 * Brad Parker (brad@heeltoe.com) 7 * 8 * Parts from dbox2_i2c.c (cvs.tuxbox.org) 9 * (C) 2000-2001 Felix Domke (tmbinc@gmx.net), Gillem (htoa@gmx.net) 10 * 11 * (C) 2007 Montavista Software, Inc. 12 * Vitaly Bordug <vitb@kernel.crashing.org> 13 * 14 * Converted to of_platform_device. Renamed to i2c-cpm.c. 15 * (C) 2007,2008 Jochen Friedrich <jochen@scram.de> 16 * 17 * This program is free software; you can redistribute it and/or modify 18 * it under the terms of the GNU General Public License as published by 19 * the Free Software Foundation; either version 2 of the License, or 20 * (at your option) any later version. 21 * 22 * This program is distributed in the hope that it will be useful, 23 * but WITHOUT ANY WARRANTY; without even the implied warranty of 24 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 25 * GNU General Public License for more details. 26 * 27 * You should have received a copy of the GNU General Public License 28 * along with this program; if not, write to the Free Software 29 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. 30 */ 31 32#include <linux/kernel.h> 33#include <linux/module.h> 34#include <linux/delay.h> 35#include <linux/slab.h> 36#include <linux/init.h> 37#include <linux/interrupt.h> 38#include <linux/errno.h> 39#include <linux/stddef.h> 40#include <linux/i2c.h> 41#include <linux/io.h> 42#include <linux/dma-mapping.h> 43#include <linux/of_device.h> 44#include <linux/of_platform.h> 45#include <linux/of_i2c.h> 46#include <sysdev/fsl_soc.h> 47#include <asm/cpm.h> 48 49/* Try to define this if you have an older CPU (earlier than rev D4) */ 50/* However, better use a GPIO based bitbang driver in this case :/ */ 51#undef I2C_CHIP_ERRATA 52 53#define CPM_MAX_READ 513 54#define CPM_MAXBD 4 55 56#define I2C_EB (0x10) /* Big endian mode */ 57#define I2C_EB_CPM2 (0x30) /* Big endian mode, memory snoop */ 58 59#define DPRAM_BASE ((u8 __iomem __force *)cpm_muram_addr(0)) 60 61/* I2C parameter RAM. */ 62struct i2c_ram { 63 ushort rbase; /* Rx Buffer descriptor base address */ 64 ushort tbase; /* Tx Buffer descriptor base address */ 65 u_char rfcr; /* Rx function code */ 66 u_char tfcr; /* Tx function code */ 67 ushort mrblr; /* Max receive buffer length */ 68 uint rstate; /* Internal */ 69 uint rdp; /* Internal */ 70 ushort rbptr; /* Rx Buffer descriptor pointer */ 71 ushort rbc; /* Internal */ 72 uint rxtmp; /* Internal */ 73 uint tstate; /* Internal */ 74 uint tdp; /* Internal */ 75 ushort tbptr; /* Tx Buffer descriptor pointer */ 76 ushort tbc; /* Internal */ 77 uint txtmp; /* Internal */ 78 char res1[4]; /* Reserved */ 79 ushort rpbase; /* Relocation pointer */ 80 char res2[2]; /* Reserved */ 81}; 82 83#define I2COM_START 0x80 84#define I2COM_MASTER 0x01 85#define I2CER_TXE 0x10 86#define I2CER_BUSY 0x04 87#define I2CER_TXB 0x02 88#define I2CER_RXB 0x01 89#define I2MOD_EN 0x01 90 91/* I2C Registers */ 92struct i2c_reg { 93 u8 i2mod; 94 u8 res1[3]; 95 u8 i2add; 96 u8 res2[3]; 97 u8 i2brg; 98 u8 res3[3]; 99 u8 i2com; 100 u8 res4[3]; 101 u8 i2cer; 102 u8 res5[3]; 103 u8 i2cmr; 104}; 105 106struct cpm_i2c { 107 char *base; 108 struct platform_device *ofdev; 109 struct i2c_adapter adap; 110 uint dp_addr; 111 int version; /* CPM1=1, CPM2=2 */ 112 int irq; 113 int cp_command; 114 int freq; 115 struct i2c_reg __iomem *i2c_reg; 116 struct i2c_ram __iomem *i2c_ram; 117 u16 i2c_addr; 118 wait_queue_head_t i2c_wait; 119 cbd_t __iomem *tbase; 120 cbd_t __iomem *rbase; 121 u_char *txbuf[CPM_MAXBD]; 122 u_char *rxbuf[CPM_MAXBD]; 123 u32 txdma[CPM_MAXBD]; 124 u32 rxdma[CPM_MAXBD]; 125}; 126 127static irqreturn_t cpm_i2c_interrupt(int irq, void *dev_id) 128{ 129 struct cpm_i2c *cpm; 130 struct i2c_reg __iomem *i2c_reg; 131 struct i2c_adapter *adap = dev_id; 132 int i; 133 134 cpm = i2c_get_adapdata(dev_id); 135 i2c_reg = cpm->i2c_reg; 136 137 /* Clear interrupt. */ 138 i = in_8(&i2c_reg->i2cer); 139 out_8(&i2c_reg->i2cer, i); 140 141 dev_dbg(&adap->dev, "Interrupt: %x\n", i); 142 143 wake_up(&cpm->i2c_wait); 144 145 return i ? IRQ_HANDLED : IRQ_NONE; 146} 147 148static void cpm_reset_i2c_params(struct cpm_i2c *cpm) 149{ 150 struct i2c_ram __iomem *i2c_ram = cpm->i2c_ram; 151 152 /* Set up the I2C parameters in the parameter ram. */ 153 out_be16(&i2c_ram->tbase, (u8 __iomem *)cpm->tbase - DPRAM_BASE); 154 out_be16(&i2c_ram->rbase, (u8 __iomem *)cpm->rbase - DPRAM_BASE); 155 156 if (cpm->version == 1) { 157 out_8(&i2c_ram->tfcr, I2C_EB); 158 out_8(&i2c_ram->rfcr, I2C_EB); 159 } else { 160 out_8(&i2c_ram->tfcr, I2C_EB_CPM2); 161 out_8(&i2c_ram->rfcr, I2C_EB_CPM2); 162 } 163 164 out_be16(&i2c_ram->mrblr, CPM_MAX_READ); 165 166 out_be32(&i2c_ram->rstate, 0); 167 out_be32(&i2c_ram->rdp, 0); 168 out_be16(&i2c_ram->rbptr, 0); 169 out_be16(&i2c_ram->rbc, 0); 170 out_be32(&i2c_ram->rxtmp, 0); 171 out_be32(&i2c_ram->tstate, 0); 172 out_be32(&i2c_ram->tdp, 0); 173 out_be16(&i2c_ram->tbptr, 0); 174 out_be16(&i2c_ram->tbc, 0); 175 out_be32(&i2c_ram->txtmp, 0); 176} 177 178static void cpm_i2c_force_close(struct i2c_adapter *adap) 179{ 180 struct cpm_i2c *cpm = i2c_get_adapdata(adap); 181 struct i2c_reg __iomem *i2c_reg = cpm->i2c_reg; 182 183 dev_dbg(&adap->dev, "cpm_i2c_force_close()\n"); 184 185 cpm_command(cpm->cp_command, CPM_CR_CLOSE_RX_BD); 186 187 out_8(&i2c_reg->i2cmr, 0x00); /* Disable all interrupts */ 188 out_8(&i2c_reg->i2cer, 0xff); 189} 190 191static void cpm_i2c_parse_message(struct i2c_adapter *adap, 192 struct i2c_msg *pmsg, int num, int tx, int rx) 193{ 194 cbd_t __iomem *tbdf; 195 cbd_t __iomem *rbdf; 196 u_char addr; 197 u_char *tb; 198 u_char *rb; 199 struct cpm_i2c *cpm = i2c_get_adapdata(adap); 200 201 tbdf = cpm->tbase + tx; 202 rbdf = cpm->rbase + rx; 203 204 addr = pmsg->addr << 1; 205 if (pmsg->flags & I2C_M_RD) 206 addr |= 1; 207 208 tb = cpm->txbuf[tx]; 209 rb = cpm->rxbuf[rx]; 210 211 /* Align read buffer */ 212 rb = (u_char *) (((ulong) rb + 1) & ~1); 213 214 tb[0] = addr; /* Device address byte w/rw flag */ 215 216 out_be16(&tbdf->cbd_datlen, pmsg->len + 1); 217 out_be16(&tbdf->cbd_sc, 0); 218 219 if (!(pmsg->flags & I2C_M_NOSTART)) 220 setbits16(&tbdf->cbd_sc, BD_I2C_START); 221 222 if (tx + 1 == num) 223 setbits16(&tbdf->cbd_sc, BD_SC_LAST | BD_SC_WRAP); 224 225 if (pmsg->flags & I2C_M_RD) { 226 /* 227 * To read, we need an empty buffer of the proper length. 228 * All that is used is the first byte for address, the remainder 229 * is just used for timing (and doesn't really have to exist). 230 */ 231 232 dev_dbg(&adap->dev, "cpm_i2c_read(abyte=0x%x)\n", addr); 233 234 out_be16(&rbdf->cbd_datlen, 0); 235 out_be16(&rbdf->cbd_sc, BD_SC_EMPTY | BD_SC_INTRPT); 236 237 if (rx + 1 == CPM_MAXBD) 238 setbits16(&rbdf->cbd_sc, BD_SC_WRAP); 239 240 eieio(); 241 setbits16(&tbdf->cbd_sc, BD_SC_READY); 242 } else { 243 dev_dbg(&adap->dev, "cpm_i2c_write(abyte=0x%x)\n", addr); 244 245 memcpy(tb+1, pmsg->buf, pmsg->len); 246 247 eieio(); 248 setbits16(&tbdf->cbd_sc, BD_SC_READY | BD_SC_INTRPT); 249 } 250} 251 252static int cpm_i2c_check_message(struct i2c_adapter *adap, 253 struct i2c_msg *pmsg, int tx, int rx) 254{ 255 cbd_t __iomem *tbdf; 256 cbd_t __iomem *rbdf; 257 u_char *tb; 258 u_char *rb; 259 struct cpm_i2c *cpm = i2c_get_adapdata(adap); 260 261 tbdf = cpm->tbase + tx; 262 rbdf = cpm->rbase + rx; 263 264 tb = cpm->txbuf[tx]; 265 rb = cpm->rxbuf[rx]; 266 267 /* Align read buffer */ 268 rb = (u_char *) (((uint) rb + 1) & ~1); 269 270 eieio(); 271 if (pmsg->flags & I2C_M_RD) { 272 dev_dbg(&adap->dev, "tx sc 0x%04x, rx sc 0x%04x\n", 273 in_be16(&tbdf->cbd_sc), in_be16(&rbdf->cbd_sc)); 274 275 if (in_be16(&tbdf->cbd_sc) & BD_SC_NAK) { 276 dev_dbg(&adap->dev, "I2C read; No ack\n"); 277 return -ENXIO; 278 } 279 if (in_be16(&rbdf->cbd_sc) & BD_SC_EMPTY) { 280 dev_err(&adap->dev, 281 "I2C read; complete but rbuf empty\n"); 282 return -EREMOTEIO; 283 } 284 if (in_be16(&rbdf->cbd_sc) & BD_SC_OV) { 285 dev_err(&adap->dev, "I2C read; Overrun\n"); 286 return -EREMOTEIO; 287 } 288 memcpy(pmsg->buf, rb, pmsg->len); 289 } else { 290 dev_dbg(&adap->dev, "tx sc %d 0x%04x\n", tx, 291 in_be16(&tbdf->cbd_sc)); 292 293 if (in_be16(&tbdf->cbd_sc) & BD_SC_NAK) { 294 dev_dbg(&adap->dev, "I2C write; No ack\n"); 295 return -ENXIO; 296 } 297 if (in_be16(&tbdf->cbd_sc) & BD_SC_UN) { 298 dev_err(&adap->dev, "I2C write; Underrun\n"); 299 return -EIO; 300 } 301 if (in_be16(&tbdf->cbd_sc) & BD_SC_CL) { 302 dev_err(&adap->dev, "I2C write; Collision\n"); 303 return -EIO; 304 } 305 } 306 return 0; 307} 308 309static int cpm_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num) 310{ 311 struct cpm_i2c *cpm = i2c_get_adapdata(adap); 312 struct i2c_reg __iomem *i2c_reg = cpm->i2c_reg; 313 struct i2c_ram __iomem *i2c_ram = cpm->i2c_ram; 314 struct i2c_msg *pmsg; 315 int ret, i; 316 int tptr; 317 int rptr; 318 cbd_t __iomem *tbdf; 319 cbd_t __iomem *rbdf; 320 321 if (num > CPM_MAXBD) 322 return -EINVAL; 323 324 /* Check if we have any oversized READ requests */ 325 for (i = 0; i < num; i++) { 326 pmsg = &msgs[i]; 327 if (pmsg->len >= CPM_MAX_READ) 328 return -EINVAL; 329 } 330 331 /* Reset to use first buffer */ 332 out_be16(&i2c_ram->rbptr, in_be16(&i2c_ram->rbase)); 333 out_be16(&i2c_ram->tbptr, in_be16(&i2c_ram->tbase)); 334 335 tbdf = cpm->tbase; 336 rbdf = cpm->rbase; 337 338 tptr = 0; 339 rptr = 0; 340 341 while (tptr < num) { 342 pmsg = &msgs[tptr]; 343 dev_dbg(&adap->dev, "R: %d T: %d\n", rptr, tptr); 344 345 cpm_i2c_parse_message(adap, pmsg, num, tptr, rptr); 346 if (pmsg->flags & I2C_M_RD) 347 rptr++; 348 tptr++; 349 } 350 /* Start transfer now */ 351 /* Enable RX/TX/Error interupts */ 352 out_8(&i2c_reg->i2cmr, I2CER_TXE | I2CER_TXB | I2CER_RXB); 353 out_8(&i2c_reg->i2cer, 0xff); /* Clear interrupt status */ 354 /* Chip bug, set enable here */ 355 setbits8(&i2c_reg->i2mod, I2MOD_EN); /* Enable */ 356 /* Begin transmission */ 357 setbits8(&i2c_reg->i2com, I2COM_START); 358 359 tptr = 0; 360 rptr = 0; 361 362 while (tptr < num) { 363 /* Check for outstanding messages */ 364 dev_dbg(&adap->dev, "test ready.\n"); 365 pmsg = &msgs[tptr]; 366 if (pmsg->flags & I2C_M_RD) 367 ret = wait_event_timeout(cpm->i2c_wait, 368 (in_be16(&tbdf[tptr].cbd_sc) & BD_SC_NAK) || 369 !(in_be16(&rbdf[rptr].cbd_sc) & BD_SC_EMPTY), 370 1 * HZ); 371 else 372 ret = wait_event_timeout(cpm->i2c_wait, 373 !(in_be16(&tbdf[tptr].cbd_sc) & BD_SC_READY), 374 1 * HZ); 375 if (ret == 0) { 376 ret = -EREMOTEIO; 377 dev_err(&adap->dev, "I2C transfer: timeout\n"); 378 goto out_err; 379 } 380 if (ret > 0) { 381 dev_dbg(&adap->dev, "ready.\n"); 382 ret = cpm_i2c_check_message(adap, pmsg, tptr, rptr); 383 tptr++; 384 if (pmsg->flags & I2C_M_RD) 385 rptr++; 386 if (ret) 387 goto out_err; 388 } 389 } 390#ifdef I2C_CHIP_ERRATA 391 /* 392 * Chip errata, clear enable. This is not needed on rev D4 CPUs. 393 * Disabling I2C too early may cause too short stop condition 394 */ 395 udelay(4); 396 clrbits8(&i2c_reg->i2mod, I2MOD_EN); 397#endif 398 return (num); 399 400out_err: 401 cpm_i2c_force_close(adap); 402#ifdef I2C_CHIP_ERRATA 403 /* 404 * Chip errata, clear enable. This is not needed on rev D4 CPUs. 405 */ 406 clrbits8(&i2c_reg->i2mod, I2MOD_EN); 407#endif 408 return ret; 409} 410 411static u32 cpm_i2c_func(struct i2c_adapter *adap) 412{ 413 return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK); 414} 415 416/* -----exported algorithm data: ------------------------------------- */ 417 418static const struct i2c_algorithm cpm_i2c_algo = { 419 .master_xfer = cpm_i2c_xfer, 420 .functionality = cpm_i2c_func, 421}; 422 423static const struct i2c_adapter cpm_ops = { 424 .owner = THIS_MODULE, 425 .name = "i2c-cpm", 426 .algo = &cpm_i2c_algo, 427}; 428 429static int __devinit cpm_i2c_setup(struct cpm_i2c *cpm) 430{ 431 struct platform_device *ofdev = cpm->ofdev; 432 const u32 *data; 433 int len, ret, i; 434 void __iomem *i2c_base; 435 cbd_t __iomem *tbdf; 436 cbd_t __iomem *rbdf; 437 unsigned char brg; 438 439 dev_dbg(&cpm->ofdev->dev, "cpm_i2c_setup()\n"); 440 441 init_waitqueue_head(&cpm->i2c_wait); 442 443 cpm->irq = of_irq_to_resource(ofdev->dev.of_node, 0, NULL); 444 if (!cpm->irq) 445 return -EINVAL; 446 447 /* Install interrupt handler. */ 448 ret = request_irq(cpm->irq, cpm_i2c_interrupt, 0, "cpm_i2c", 449 &cpm->adap); 450 if (ret) 451 return ret; 452 453 /* I2C parameter RAM */ 454 i2c_base = of_iomap(ofdev->dev.of_node, 1); 455 if (i2c_base == NULL) { 456 ret = -EINVAL; 457 goto out_irq; 458 } 459 460 if (of_device_is_compatible(ofdev->dev.of_node, "fsl,cpm1-i2c")) { 461 462 /* Check for and use a microcode relocation patch. */ 463 cpm->i2c_ram = i2c_base; 464 cpm->i2c_addr = in_be16(&cpm->i2c_ram->rpbase); 465 466 /* 467 * Maybe should use cpm_muram_alloc instead of hardcoding 468 * this in micropatch.c 469 */ 470 if (cpm->i2c_addr) { 471 cpm->i2c_ram = cpm_muram_addr(cpm->i2c_addr); 472 iounmap(i2c_base); 473 } 474 475 cpm->version = 1; 476 477 } else if (of_device_is_compatible(ofdev->dev.of_node, "fsl,cpm2-i2c")) { 478 cpm->i2c_addr = cpm_muram_alloc(sizeof(struct i2c_ram), 64); 479 cpm->i2c_ram = cpm_muram_addr(cpm->i2c_addr); 480 out_be16(i2c_base, cpm->i2c_addr); 481 iounmap(i2c_base); 482 483 cpm->version = 2; 484 485 } else { 486 iounmap(i2c_base); 487 ret = -EINVAL; 488 goto out_irq; 489 } 490 491 /* I2C control/status registers */ 492 cpm->i2c_reg = of_iomap(ofdev->dev.of_node, 0); 493 if (cpm->i2c_reg == NULL) { 494 ret = -EINVAL; 495 goto out_ram; 496 } 497 498 data = of_get_property(ofdev->dev.of_node, "fsl,cpm-command", &len); 499 if (!data || len != 4) { 500 ret = -EINVAL; 501 goto out_reg; 502 } 503 cpm->cp_command = *data; 504 505 data = of_get_property(ofdev->dev.of_node, "linux,i2c-class", &len); 506 if (data && len == 4) 507 cpm->adap.class = *data; 508 509 data = of_get_property(ofdev->dev.of_node, "clock-frequency", &len); 510 if (data && len == 4) 511 cpm->freq = *data; 512 else 513 cpm->freq = 60000; /* use 60kHz i2c clock by default */ 514 515 /* 516 * Allocate space for CPM_MAXBD transmit and receive buffer 517 * descriptors in the DP ram. 518 */ 519 cpm->dp_addr = cpm_muram_alloc(sizeof(cbd_t) * 2 * CPM_MAXBD, 8); 520 if (!cpm->dp_addr) { 521 ret = -ENOMEM; 522 goto out_reg; 523 } 524 525 cpm->tbase = cpm_muram_addr(cpm->dp_addr); 526 cpm->rbase = cpm_muram_addr(cpm->dp_addr + sizeof(cbd_t) * CPM_MAXBD); 527 528 /* Allocate TX and RX buffers */ 529 530 tbdf = cpm->tbase; 531 rbdf = cpm->rbase; 532 533 for (i = 0; i < CPM_MAXBD; i++) { 534 cpm->rxbuf[i] = dma_alloc_coherent(&cpm->ofdev->dev, 535 CPM_MAX_READ + 1, 536 &cpm->rxdma[i], GFP_KERNEL); 537 if (!cpm->rxbuf[i]) { 538 ret = -ENOMEM; 539 goto out_muram; 540 } 541 out_be32(&rbdf[i].cbd_bufaddr, ((cpm->rxdma[i] + 1) & ~1)); 542 543 cpm->txbuf[i] = (unsigned char *)dma_alloc_coherent(&cpm->ofdev->dev, CPM_MAX_READ + 1, &cpm->txdma[i], GFP_KERNEL); 544 if (!cpm->txbuf[i]) { 545 ret = -ENOMEM; 546 goto out_muram; 547 } 548 out_be32(&tbdf[i].cbd_bufaddr, cpm->txdma[i]); 549 } 550 551 /* Initialize Tx/Rx parameters. */ 552 553 cpm_reset_i2c_params(cpm); 554 555 dev_dbg(&cpm->ofdev->dev, "i2c_ram 0x%p, i2c_addr 0x%04x, freq %d\n", 556 cpm->i2c_ram, cpm->i2c_addr, cpm->freq); 557 dev_dbg(&cpm->ofdev->dev, "tbase 0x%04x, rbase 0x%04x\n", 558 (u8 __iomem *)cpm->tbase - DPRAM_BASE, 559 (u8 __iomem *)cpm->rbase - DPRAM_BASE); 560 561 cpm_command(cpm->cp_command, CPM_CR_INIT_TRX); 562 563 /* 564 * Select an invalid address. Just make sure we don't use loopback mode 565 */ 566 out_8(&cpm->i2c_reg->i2add, 0x7f << 1); 567 568 /* 569 * PDIV is set to 00 in i2mod, so brgclk/32 is used as input to the 570 * i2c baud rate generator. This is divided by 2 x (DIV + 3) to get 571 * the actual i2c bus frequency. 572 */ 573 brg = get_brgfreq() / (32 * 2 * cpm->freq) - 3; 574 out_8(&cpm->i2c_reg->i2brg, brg); 575 576 out_8(&cpm->i2c_reg->i2mod, 0x00); 577 out_8(&cpm->i2c_reg->i2com, I2COM_MASTER); /* Master mode */ 578 579 /* Disable interrupts. */ 580 out_8(&cpm->i2c_reg->i2cmr, 0); 581 out_8(&cpm->i2c_reg->i2cer, 0xff); 582 583 return 0; 584 585out_muram: 586 for (i = 0; i < CPM_MAXBD; i++) { 587 if (cpm->rxbuf[i]) 588 dma_free_coherent(&cpm->ofdev->dev, CPM_MAX_READ + 1, 589 cpm->rxbuf[i], cpm->rxdma[i]); 590 if (cpm->txbuf[i]) 591 dma_free_coherent(&cpm->ofdev->dev, CPM_MAX_READ + 1, 592 cpm->txbuf[i], cpm->txdma[i]); 593 } 594 cpm_muram_free(cpm->dp_addr); 595out_reg: 596 iounmap(cpm->i2c_reg); 597out_ram: 598 if ((cpm->version == 1) && (!cpm->i2c_addr)) 599 iounmap(cpm->i2c_ram); 600 if (cpm->version == 2) 601 cpm_muram_free(cpm->i2c_addr); 602out_irq: 603 free_irq(cpm->irq, &cpm->adap); 604 return ret; 605} 606 607static void cpm_i2c_shutdown(struct cpm_i2c *cpm) 608{ 609 int i; 610 611 /* Shut down I2C. */ 612 clrbits8(&cpm->i2c_reg->i2mod, I2MOD_EN); 613 614 /* Disable interrupts */ 615 out_8(&cpm->i2c_reg->i2cmr, 0); 616 out_8(&cpm->i2c_reg->i2cer, 0xff); 617 618 free_irq(cpm->irq, &cpm->adap); 619 620 /* Free all memory */ 621 for (i = 0; i < CPM_MAXBD; i++) { 622 dma_free_coherent(&cpm->ofdev->dev, CPM_MAX_READ + 1, 623 cpm->rxbuf[i], cpm->rxdma[i]); 624 dma_free_coherent(&cpm->ofdev->dev, CPM_MAX_READ + 1, 625 cpm->txbuf[i], cpm->txdma[i]); 626 } 627 628 cpm_muram_free(cpm->dp_addr); 629 iounmap(cpm->i2c_reg); 630 631 if ((cpm->version == 1) && (!cpm->i2c_addr)) 632 iounmap(cpm->i2c_ram); 633 if (cpm->version == 2) 634 cpm_muram_free(cpm->i2c_addr); 635} 636 637static int __devinit cpm_i2c_probe(struct platform_device *ofdev) 638{ 639 int result, len; 640 struct cpm_i2c *cpm; 641 const u32 *data; 642 643 cpm = kzalloc(sizeof(struct cpm_i2c), GFP_KERNEL); 644 if (!cpm) 645 return -ENOMEM; 646 647 cpm->ofdev = ofdev; 648 649 dev_set_drvdata(&ofdev->dev, cpm); 650 651 cpm->adap = cpm_ops; 652 i2c_set_adapdata(&cpm->adap, cpm); 653 cpm->adap.dev.parent = &ofdev->dev; 654 cpm->adap.dev.of_node = of_node_get(ofdev->dev.of_node); 655 656 result = cpm_i2c_setup(cpm); 657 if (result) { 658 dev_err(&ofdev->dev, "Unable to init hardware\n"); 659 goto out_free; 660 } 661 662 /* register new adapter to i2c module... */ 663 664 data = of_get_property(ofdev->dev.of_node, "linux,i2c-index", &len); 665 cpm->adap.nr = (data && len == 4) ? be32_to_cpup(data) : -1; 666 result = i2c_add_numbered_adapter(&cpm->adap); 667 668 if (result < 0) { 669 dev_err(&ofdev->dev, "Unable to register with I2C\n"); 670 goto out_shut; 671 } 672 673 dev_dbg(&ofdev->dev, "hw routines for %s registered.\n", 674 cpm->adap.name); 675 676 /* 677 * register OF I2C devices 678 */ 679 of_i2c_register_devices(&cpm->adap); 680 681 return 0; 682out_shut: 683 cpm_i2c_shutdown(cpm); 684out_free: 685 dev_set_drvdata(&ofdev->dev, NULL); 686 kfree(cpm); 687 688 return result; 689} 690 691static int __devexit cpm_i2c_remove(struct platform_device *ofdev) 692{ 693 struct cpm_i2c *cpm = dev_get_drvdata(&ofdev->dev); 694 695 i2c_del_adapter(&cpm->adap); 696 697 cpm_i2c_shutdown(cpm); 698 699 dev_set_drvdata(&ofdev->dev, NULL); 700 kfree(cpm); 701 702 return 0; 703} 704 705static const struct of_device_id cpm_i2c_match[] = { 706 { 707 .compatible = "fsl,cpm1-i2c", 708 }, 709 { 710 .compatible = "fsl,cpm2-i2c", 711 }, 712 {}, 713}; 714 715MODULE_DEVICE_TABLE(of, cpm_i2c_match); 716 717static struct platform_driver cpm_i2c_driver = { 718 .probe = cpm_i2c_probe, 719 .remove = __devexit_p(cpm_i2c_remove), 720 .driver = { 721 .name = "fsl-i2c-cpm", 722 .owner = THIS_MODULE, 723 .of_match_table = cpm_i2c_match, 724 }, 725}; 726 727module_platform_driver(cpm_i2c_driver); 728 729MODULE_AUTHOR("Jochen Friedrich <jochen@scram.de>"); 730MODULE_DESCRIPTION("I2C-Bus adapter routines for CPM boards"); 731MODULE_LICENSE("GPL"); 732