1# 2# Multimedia Video device configuration 3# 4 5menuconfig RADIO_ADAPTERS 6 bool "Radio Adapters" 7 depends on VIDEO_V4L2 8 default y 9 ---help--- 10 Say Y here to enable selecting AM/FM radio adapters. 11 12if RADIO_ADAPTERS && VIDEO_V4L2 13 14config RADIO_SI470X 15 bool "Silicon Labs Si470x FM Radio Receiver support" 16 depends on VIDEO_V4L2 17 18source "drivers/media/radio/si470x/Kconfig" 19 20config USB_MR800 21 tristate "AverMedia MR 800 USB FM radio support" 22 depends on USB && VIDEO_V4L2 23 ---help--- 24 Say Y here if you want to connect this type of radio to your 25 computer's USB port. Note that the audio is not digital, and 26 you must connect the line out connector to a sound card or a 27 set of speakers. 28 29 To compile this driver as a module, choose M here: the 30 module will be called radio-mr800. 31 32config USB_DSBR 33 tristate "D-Link/GemTek USB FM radio support" 34 depends on USB && VIDEO_V4L2 35 ---help--- 36 Say Y here if you want to connect this type of radio to your 37 computer's USB port. Note that the audio is not digital, and 38 you must connect the line out connector to a sound card or a 39 set of speakers. 40 41 To compile this driver as a module, choose M here: the 42 module will be called dsbr100. 43 44config RADIO_MAXIRADIO 45 tristate "Guillemot MAXI Radio FM 2000 radio" 46 depends on VIDEO_V4L2 && PCI && SND 47 ---help--- 48 Choose Y here if you have this radio card. This card may also be 49 found as Gemtek PCI FM. 50 51 In order to control your radio card, you will need to use programs 52 that are compatible with the Video For Linux API. Information on 53 this API and pointers to "v4l" programs may be found at 54 <file:Documentation/video4linux/API.html>. 55 56 To compile this driver as a module, choose M here: the 57 module will be called radio-maxiradio. 58 59 60config I2C_SI4713 61 tristate "I2C driver for Silicon Labs Si4713 device" 62 depends on I2C && VIDEO_V4L2 63 ---help--- 64 Say Y here if you want support to Si4713 I2C device. 65 This device driver supports only i2c bus. 66 67 To compile this driver as a module, choose M here: the 68 module will be called si4713. 69 70config RADIO_SI4713 71 tristate "Silicon Labs Si4713 FM Radio Transmitter support" 72 depends on I2C && VIDEO_V4L2 73 select I2C_SI4713 74 ---help--- 75 Say Y here if you want support to Si4713 FM Radio Transmitter. 76 This device can transmit audio through FM. It can transmit 77 RDS and RBDS signals as well. This module is the v4l2 radio 78 interface for the i2c driver of this device. 79 80 To compile this driver as a module, choose M here: the 81 module will be called radio-si4713. 82 83config USB_KEENE 84 tristate "Keene FM Transmitter USB support" 85 depends on USB && VIDEO_V4L2 86 ---help--- 87 Say Y here if you want to connect this type of FM transmitter 88 to your computer's USB port. 89 90 To compile this driver as a module, choose M here: the 91 module will be called radio-keene. 92 93config RADIO_TEA5764 94 tristate "TEA5764 I2C FM radio support" 95 depends on I2C && VIDEO_V4L2 96 ---help--- 97 Say Y here if you want to use the TEA5764 FM chip found in 98 EZX phones. This FM chip is present in EZX phones from Motorola, 99 connected to internal pxa I2C bus. 100 101 To compile this driver as a module, choose M here: the 102 module will be called radio-tea5764. 103 104config RADIO_TEA5764_XTAL 105 bool "TEA5764 crystal reference" 106 depends on RADIO_TEA5764=y 107 default y 108 help 109 Say Y here if TEA5764 have a 32768 Hz crystal in circuit, say N 110 here if TEA5764 reference frequency is connected in FREQIN. 111 112config RADIO_SAA7706H 113 tristate "SAA7706H Car Radio DSP" 114 depends on I2C && VIDEO_V4L2 115 ---help--- 116 Say Y here if you want to use the SAA7706H Car radio Digital 117 Signal Processor, found for instance on the Russellville development 118 board. On the russellville the device is connected to internal 119 timberdale I2C bus. 120 121 To compile this driver as a module, choose M here: the 122 module will be called SAA7706H. 123 124config RADIO_TEF6862 125 tristate "TEF6862 Car Radio Enhanced Selectivity Tuner" 126 depends on I2C && VIDEO_V4L2 127 ---help--- 128 Say Y here if you want to use the TEF6862 Car Radio Enhanced 129 Selectivity Tuner, found for instance on the Russellville development 130 board. On the russellville the device is connected to internal 131 timberdale I2C bus. 132 133 To compile this driver as a module, choose M here: the 134 module will be called TEF6862. 135 136config RADIO_TIMBERDALE 137 tristate "Enable the Timberdale radio driver" 138 depends on MFD_TIMBERDALE && VIDEO_V4L2 139 depends on I2C # for RADIO_SAA7706H 140 select RADIO_TEF6862 141 select RADIO_SAA7706H 142 ---help--- 143 This is a kind of umbrella driver for the Radio Tuner and DSP 144 found behind the Timberdale FPGA on the Russellville board. 145 Enabling this driver will automatically select the DSP and tuner. 146 147config RADIO_WL1273 148 tristate "Texas Instruments WL1273 I2C FM Radio" 149 depends on I2C && VIDEO_V4L2 150 select MFD_CORE 151 select MFD_WL1273_CORE 152 select FW_LOADER 153 ---help--- 154 Choose Y here if you have this FM radio chip. 155 156 In order to control your radio card, you will need to use programs 157 that are compatible with the Video For Linux 2 API. Information on 158 this API and pointers to "v4l2" programs may be found at 159 <file:Documentation/video4linux/API.html>. 160 161 To compile this driver as a module, choose M here: the 162 module will be called radio-wl1273. 163 164# TI's ST based wl128x FM radio 165source "drivers/media/radio/wl128x/Kconfig" 166 167# 168# ISA drivers configuration 169# 170 171menuconfig V4L_RADIO_ISA_DRIVERS 172 bool "ISA radio devices" 173 depends on ISA 174 default n 175 ---help--- 176 Say Y here to enable support for these ISA drivers. 177 178if V4L_RADIO_ISA_DRIVERS 179 180config RADIO_ISA 181 depends on ISA 182 tristate 183 184config RADIO_CADET 185 tristate "ADS Cadet AM/FM Tuner" 186 depends on ISA && VIDEO_V4L2 187 ---help--- 188 Choose Y here if you have one of these AM/FM radio cards, and then 189 fill in the port address below. 190 191 To compile this driver as a module, choose M here: the 192 module will be called radio-cadet. 193 194config RADIO_RTRACK 195 tristate "AIMSlab RadioTrack (aka RadioReveal) support" 196 depends on ISA && VIDEO_V4L2 197 select RADIO_ISA 198 ---help--- 199 Choose Y here if you have one of these FM radio cards, and then fill 200 in the port address below. 201 202 Note that newer AIMSlab RadioTrack cards have a different chipset 203 and are not supported by this driver. For these cards, use the 204 RadioTrack II driver below. 205 206 If you have a GemTeks combined (PnP) sound- and radio card you must 207 use this driver as a module and setup the card with isapnptools. 208 You must also pass the module a suitable io parameter, 0x248 has 209 been reported to be used by these cards. 210 211 More information is contained in the file 212 <file:Documentation/video4linux/radiotrack.txt>. 213 214 To compile this driver as a module, choose M here: the 215 module will be called radio-aimslab. 216 217config RADIO_RTRACK_PORT 218 hex "RadioTrack i/o port (0x20f or 0x30f)" 219 depends on RADIO_RTRACK=y 220 default "30f" 221 help 222 Enter either 0x30f or 0x20f here. The card default is 0x30f, if you 223 haven't changed the jumper setting on the card. 224 225config RADIO_RTRACK2 226 tristate "AIMSlab RadioTrack II support" 227 depends on ISA && VIDEO_V4L2 228 select RADIO_ISA 229 ---help--- 230 Choose Y here if you have this FM radio card, and then fill in the 231 port address below. 232 233 Note: this driver hasn't been tested since a long time due to lack 234 of hardware. If you have this hardware, then please contact the 235 linux-media mailinglist. 236 237 To compile this driver as a module, choose M here: the 238 module will be called radio-rtrack2. 239 240config RADIO_RTRACK2_PORT 241 hex "RadioTrack II i/o port (0x20c or 0x30c)" 242 depends on RADIO_RTRACK2=y 243 default "30c" 244 help 245 Enter either 0x30c or 0x20c here. The card default is 0x30c, if you 246 haven't changed the jumper setting on the card. 247 248config RADIO_AZTECH 249 tristate "Aztech/Packard Bell Radio" 250 depends on ISA && VIDEO_V4L2 251 select RADIO_ISA 252 ---help--- 253 Choose Y here if you have one of these FM radio cards, and then fill 254 in the port address below. 255 256 To compile this driver as a module, choose M here: the 257 module will be called radio-aztech. 258 259config RADIO_AZTECH_PORT 260 hex "Aztech/Packard Bell I/O port (0x350 or 0x358)" 261 depends on RADIO_AZTECH=y 262 default "350" 263 help 264 Enter either 0x350 or 0x358 here. The card default is 0x350, if you 265 haven't changed the setting of jumper JP3 on the card. Removing the 266 jumper sets the card to 0x358. 267 268config RADIO_GEMTEK 269 tristate "GemTek Radio card (or compatible) support" 270 depends on ISA && VIDEO_V4L2 271 select RADIO_ISA 272 ---help--- 273 Choose Y here if you have this FM radio card, and then fill in the 274 I/O port address and settings below. The following cards either have 275 GemTek Radio tuner or are rebranded GemTek Radio cards: 276 277 - Sound Vision 16 Gold with FM Radio 278 - Typhoon Radio card (some models) 279 - Hama Radio card 280 281 To compile this driver as a module, choose M here: the 282 module will be called radio-gemtek. 283 284config RADIO_GEMTEK_PORT 285 hex "Fixed I/O port (0x20c, 0x30c, 0x24c, 0x34c, 0x248 or 0x28c)" 286 depends on RADIO_GEMTEK=y 287 default "34c" 288 help 289 Enter either 0x20c, 0x30c, 0x24c, 0x34c, 0x248 or 0x28c here. The 290 card default is 0x34c, if you haven't changed the jumper setting 291 on the card. 292 293 On Sound Vision 16 Gold PnP with FM Radio (ESS1869+FM Gemtek), the I/O 294 port is 0x20c, 0x248 or 0x28c. 295 296 If automatic I/O port probing is enabled this port will be used only 297 in case of automatic probing failure, ie. as a fallback. 298 299config RADIO_GEMTEK_PROBE 300 bool "Automatic I/O port probing" 301 depends on RADIO_GEMTEK=y 302 default y 303 help 304 Say Y here to enable automatic probing for GemTek Radio card. The 305 following ports will be probed: 0x20c, 0x30c, 0x24c, 0x34c, 0x248 and 306 0x28c. 307 308config RADIO_MIROPCM20 309 tristate "miroSOUND PCM20 radio" 310 depends on ISA && ISA_DMA_API && VIDEO_V4L2 && SND 311 select SND_ISA 312 select SND_MIRO 313 ---help--- 314 Choose Y here if you have this FM radio card. You also need to enable 315 the ALSA sound system. This choice automatically selects the ALSA 316 sound card driver "Miro miroSOUND PCM1pro/PCM12/PCM20radio" as this 317 is required for the radio-miropcm20. 318 319 To compile this driver as a module, choose M here: the 320 module will be called radio-miropcm20. 321 322config RADIO_SF16FMI 323 tristate "SF16-FMI/SF16-FMP Radio" 324 depends on ISA && VIDEO_V4L2 325 ---help--- 326 Choose Y here if you have one of these FM radio cards. 327 328 To compile this driver as a module, choose M here: the 329 module will be called radio-sf16fmi. 330 331config RADIO_SF16FMR2 332 tristate "SF16FMR2 Radio" 333 depends on ISA && VIDEO_V4L2 && SND 334 ---help--- 335 Choose Y here if you have one of these FM radio cards. 336 337 To compile this driver as a module, choose M here: the 338 module will be called radio-sf16fmr2. 339 340config RADIO_TERRATEC 341 tristate "TerraTec ActiveRadio ISA Standalone" 342 depends on ISA && VIDEO_V4L2 343 select RADIO_ISA 344 ---help--- 345 Choose Y here if you have this FM radio card. 346 347 Note: this driver hasn't been tested since a long time due to lack 348 of hardware. If you have this hardware, then please contact the 349 linux-media mailinglist. 350 351 To compile this driver as a module, choose M here: the 352 module will be called radio-terratec. 353 354config RADIO_TRUST 355 tristate "Trust FM radio card" 356 depends on ISA && VIDEO_V4L2 357 select RADIO_ISA 358 help 359 This is a driver for the Trust FM radio cards. Say Y if you have 360 such a card and want to use it under Linux. 361 362 Note: this driver hasn't been tested since a long time due to lack 363 of hardware. If you have this hardware, then please contact the 364 linux-media mailinglist. 365 366 To compile this driver as a module, choose M here: the 367 module will be called radio-trust. 368 369config RADIO_TRUST_PORT 370 hex "Trust i/o port (usually 0x350 or 0x358)" 371 depends on RADIO_TRUST=y 372 default "350" 373 help 374 Enter the I/O port of your Trust FM radio card. If unsure, try the 375 values "0x350" or "0x358". 376 377config RADIO_TYPHOON 378 tristate "Typhoon Radio (a.k.a. EcoRadio)" 379 depends on ISA && VIDEO_V4L2 380 select RADIO_ISA 381 ---help--- 382 Choose Y here if you have one of these FM radio cards, and then fill 383 in the port address and the frequency used for muting below. 384 385 Note: this driver hasn't been tested since a long time due to lack 386 of hardware. If you have this hardware, then please contact the 387 linux-media mailinglist. 388 389 To compile this driver as a module, choose M here: the 390 module will be called radio-typhoon. 391 392config RADIO_TYPHOON_PORT 393 hex "Typhoon I/O port (0x316 or 0x336)" 394 depends on RADIO_TYPHOON=y 395 default "316" 396 help 397 Enter the I/O port of your Typhoon or EcoRadio radio card. 398 399config RADIO_TYPHOON_MUTEFREQ 400 int "Typhoon frequency set when muting the device (kHz)" 401 depends on RADIO_TYPHOON=y 402 default "87500" 403 help 404 Enter the frequency used for muting the radio. The device is never 405 completely silent. If the volume is just turned down, you can still 406 hear silent voices and music. For that reason, the frequency of the 407 radio device is set to the frequency you can enter here whenever 408 the device is muted. There should be no local radio station at that 409 frequency. 410 411config RADIO_ZOLTRIX 412 tristate "Zoltrix Radio" 413 depends on ISA && VIDEO_V4L2 414 select RADIO_ISA 415 ---help--- 416 Choose Y here if you have one of these FM radio cards, and then fill 417 in the port address below. 418 419 Note: this driver hasn't been tested since a long time due to lack 420 of hardware. If you have this hardware, then please contact the 421 linux-media mailinglist. 422 423 To compile this driver as a module, choose M here: the 424 module will be called radio-zoltrix. 425 426config RADIO_ZOLTRIX_PORT 427 hex "ZOLTRIX I/O port (0x20c or 0x30c)" 428 depends on RADIO_ZOLTRIX=y 429 default "20c" 430 help 431 Enter the I/O port of your Zoltrix radio card. 432 433endif # V4L_RADIO_ISA_DRIVERS 434 435endif # RADIO_ADAPTERS 436