1/* 2 * Driver for PowerMac Z85c30 based ESCC cell found in the 3 * "macio" ASICs of various PowerMac models 4 * 5 * Copyright (C) 2003 Ben. Herrenschmidt (benh@kernel.crashing.org) 6 * 7 * Derived from drivers/macintosh/macserial.c by Paul Mackerras 8 * and drivers/serial/sunzilog.c by David S. Miller 9 * 10 * Hrm... actually, I ripped most of sunzilog (Thanks David !) and 11 * adapted special tweaks needed for us. I don't think it's worth 12 * merging back those though. The DMA code still has to get in 13 * and once done, I expect that driver to remain fairly stable in 14 * the long term, unless we change the driver model again... 15 * 16 * This program is free software; you can redistribute it and/or modify 17 * it under the terms of the GNU General Public License as published by 18 * the Free Software Foundation; either version 2 of the License, or 19 * (at your option) any later version. 20 * 21 * This program is distributed in the hope that it will be useful, 22 * but WITHOUT ANY WARRANTY; without even the implied warranty of 23 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 24 * GNU General Public License for more details. 25 * 26 * You should have received a copy of the GNU General Public License 27 * along with this program; if not, write to the Free Software 28 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA 29 * 30 * 2004-08-06 Harald Welte <laforge@gnumonks.org> 31 * - Enable BREAK interrupt 32 * - Add support for sysreq 33 * 34 * TODO: - Add DMA support 35 * - Defer port shutdown to a few seconds after close 36 * - maybe put something right into uap->clk_divisor 37 */ 38 39#undef DEBUG 40#undef DEBUG_HARD 41#undef USE_CTRL_O_SYSRQ 42 43#include <linux/module.h> 44#include <linux/tty.h> 45 46#include <linux/tty_flip.h> 47#include <linux/major.h> 48#include <linux/string.h> 49#include <linux/fcntl.h> 50#include <linux/mm.h> 51#include <linux/kernel.h> 52#include <linux/delay.h> 53#include <linux/init.h> 54#include <linux/console.h> 55#include <linux/adb.h> 56#include <linux/pmu.h> 57#include <linux/bitops.h> 58#include <linux/sysrq.h> 59#include <linux/mutex.h> 60#include <asm/sections.h> 61#include <asm/io.h> 62#include <asm/irq.h> 63 64#ifdef CONFIG_PPC_PMAC 65#include <asm/prom.h> 66#include <asm/machdep.h> 67#include <asm/pmac_feature.h> 68#include <asm/dbdma.h> 69#include <asm/macio.h> 70#else 71#include <linux/platform_device.h> 72#define of_machine_is_compatible(x) (0) 73#endif 74 75#if defined (CONFIG_SERIAL_PMACZILOG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) 76#define SUPPORT_SYSRQ 77#endif 78 79#include <linux/serial.h> 80#include <linux/serial_core.h> 81 82#include "pmac_zilog.h" 83 84/* Not yet implemented */ 85#undef HAS_DBDMA 86 87static char version[] __initdata = "pmac_zilog: 0.6 (Benjamin Herrenschmidt <benh@kernel.crashing.org>)"; 88MODULE_AUTHOR("Benjamin Herrenschmidt <benh@kernel.crashing.org>"); 89MODULE_DESCRIPTION("Driver for the Mac and PowerMac serial ports."); 90MODULE_LICENSE("GPL"); 91 92#ifdef CONFIG_SERIAL_PMACZILOG_TTYS 93#define PMACZILOG_MAJOR TTY_MAJOR 94#define PMACZILOG_MINOR 64 95#define PMACZILOG_NAME "ttyS" 96#else 97#define PMACZILOG_MAJOR 204 98#define PMACZILOG_MINOR 192 99#define PMACZILOG_NAME "ttyPZ" 100#endif 101 102#define pmz_debug(fmt, arg...) pr_debug("ttyPZ%d: " fmt, uap->port.line, ## arg) 103#define pmz_error(fmt, arg...) pr_err("ttyPZ%d: " fmt, uap->port.line, ## arg) 104#define pmz_info(fmt, arg...) pr_info("ttyPZ%d: " fmt, uap->port.line, ## arg) 105 106/* 107 * For the sake of early serial console, we can do a pre-probe 108 * (optional) of the ports at rather early boot time. 109 */ 110static struct uart_pmac_port pmz_ports[MAX_ZS_PORTS]; 111static int pmz_ports_count; 112 113static struct uart_driver pmz_uart_reg = { 114 .owner = THIS_MODULE, 115 .driver_name = PMACZILOG_NAME, 116 .dev_name = PMACZILOG_NAME, 117 .major = PMACZILOG_MAJOR, 118 .minor = PMACZILOG_MINOR, 119}; 120 121 122/* 123 * Load all registers to reprogram the port 124 * This function must only be called when the TX is not busy. The UART 125 * port lock must be held and local interrupts disabled. 126 */ 127static void pmz_load_zsregs(struct uart_pmac_port *uap, u8 *regs) 128{ 129 int i; 130 131 /* Let pending transmits finish. */ 132 for (i = 0; i < 1000; i++) { 133 unsigned char stat = read_zsreg(uap, R1); 134 if (stat & ALL_SNT) 135 break; 136 udelay(100); 137 } 138 139 ZS_CLEARERR(uap); 140 zssync(uap); 141 ZS_CLEARFIFO(uap); 142 zssync(uap); 143 ZS_CLEARERR(uap); 144 145 /* Disable all interrupts. */ 146 write_zsreg(uap, R1, 147 regs[R1] & ~(RxINT_MASK | TxINT_ENAB | EXT_INT_ENAB)); 148 149 /* Set parity, sync config, stop bits, and clock divisor. */ 150 write_zsreg(uap, R4, regs[R4]); 151 152 /* Set misc. TX/RX control bits. */ 153 write_zsreg(uap, R10, regs[R10]); 154 155 /* Set TX/RX controls sans the enable bits. */ 156 write_zsreg(uap, R3, regs[R3] & ~RxENABLE); 157 write_zsreg(uap, R5, regs[R5] & ~TxENABLE); 158 159 /* now set R7 "prime" on ESCC */ 160 write_zsreg(uap, R15, regs[R15] | EN85C30); 161 write_zsreg(uap, R7, regs[R7P]); 162 163 /* make sure we use R7 "non-prime" on ESCC */ 164 write_zsreg(uap, R15, regs[R15] & ~EN85C30); 165 166 /* Synchronous mode config. */ 167 write_zsreg(uap, R6, regs[R6]); 168 write_zsreg(uap, R7, regs[R7]); 169 170 /* Disable baud generator. */ 171 write_zsreg(uap, R14, regs[R14] & ~BRENAB); 172 173 /* Clock mode control. */ 174 write_zsreg(uap, R11, regs[R11]); 175 176 /* Lower and upper byte of baud rate generator divisor. */ 177 write_zsreg(uap, R12, regs[R12]); 178 write_zsreg(uap, R13, regs[R13]); 179 180 /* Now rewrite R14, with BRENAB (if set). */ 181 write_zsreg(uap, R14, regs[R14]); 182 183 /* Reset external status interrupts. */ 184 write_zsreg(uap, R0, RES_EXT_INT); 185 write_zsreg(uap, R0, RES_EXT_INT); 186 187 /* Rewrite R3/R5, this time without enables masked. */ 188 write_zsreg(uap, R3, regs[R3]); 189 write_zsreg(uap, R5, regs[R5]); 190 191 /* Rewrite R1, this time without IRQ enabled masked. */ 192 write_zsreg(uap, R1, regs[R1]); 193 194 /* Enable interrupts */ 195 write_zsreg(uap, R9, regs[R9]); 196} 197 198/* 199 * We do like sunzilog to avoid disrupting pending Tx 200 * Reprogram the Zilog channel HW registers with the copies found in the 201 * software state struct. If the transmitter is busy, we defer this update 202 * until the next TX complete interrupt. Else, we do it right now. 203 * 204 * The UART port lock must be held and local interrupts disabled. 205 */ 206static void pmz_maybe_update_regs(struct uart_pmac_port *uap) 207{ 208 if (!ZS_REGS_HELD(uap)) { 209 if (ZS_TX_ACTIVE(uap)) { 210 uap->flags |= PMACZILOG_FLAG_REGS_HELD; 211 } else { 212 pmz_debug("pmz: maybe_update_regs: updating\n"); 213 pmz_load_zsregs(uap, uap->curregs); 214 } 215 } 216} 217 218static void pmz_interrupt_control(struct uart_pmac_port *uap, int enable) 219{ 220 if (enable) { 221 uap->curregs[1] |= INT_ALL_Rx | TxINT_ENAB; 222 if (!ZS_IS_EXTCLK(uap)) 223 uap->curregs[1] |= EXT_INT_ENAB; 224 } else { 225 uap->curregs[1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK); 226 } 227 write_zsreg(uap, R1, uap->curregs[1]); 228} 229 230static struct tty_struct *pmz_receive_chars(struct uart_pmac_port *uap) 231{ 232 struct tty_struct *tty = NULL; 233 unsigned char ch, r1, drop, error, flag; 234 int loops = 0; 235 236 /* Sanity check, make sure the old bug is no longer happening */ 237 if (uap->port.state == NULL || uap->port.state->port.tty == NULL) { 238 WARN_ON(1); 239 (void)read_zsdata(uap); 240 return NULL; 241 } 242 tty = uap->port.state->port.tty; 243 244 while (1) { 245 error = 0; 246 drop = 0; 247 248 r1 = read_zsreg(uap, R1); 249 ch = read_zsdata(uap); 250 251 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) { 252 write_zsreg(uap, R0, ERR_RES); 253 zssync(uap); 254 } 255 256 ch &= uap->parity_mask; 257 if (ch == 0 && uap->flags & PMACZILOG_FLAG_BREAK) { 258 uap->flags &= ~PMACZILOG_FLAG_BREAK; 259 } 260 261#if defined(CONFIG_MAGIC_SYSRQ) && defined(CONFIG_SERIAL_CORE_CONSOLE) 262#ifdef USE_CTRL_O_SYSRQ 263 /* Handle the SysRq ^O Hack */ 264 if (ch == '\x0f') { 265 uap->port.sysrq = jiffies + HZ*5; 266 goto next_char; 267 } 268#endif /* USE_CTRL_O_SYSRQ */ 269 if (uap->port.sysrq) { 270 int swallow; 271 spin_unlock(&uap->port.lock); 272 swallow = uart_handle_sysrq_char(&uap->port, ch); 273 spin_lock(&uap->port.lock); 274 if (swallow) 275 goto next_char; 276 } 277#endif /* CONFIG_MAGIC_SYSRQ && CONFIG_SERIAL_CORE_CONSOLE */ 278 279 /* A real serial line, record the character and status. */ 280 if (drop) 281 goto next_char; 282 283 flag = TTY_NORMAL; 284 uap->port.icount.rx++; 285 286 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR | BRK_ABRT)) { 287 error = 1; 288 if (r1 & BRK_ABRT) { 289 pmz_debug("pmz: got break !\n"); 290 r1 &= ~(PAR_ERR | CRC_ERR); 291 uap->port.icount.brk++; 292 if (uart_handle_break(&uap->port)) 293 goto next_char; 294 } 295 else if (r1 & PAR_ERR) 296 uap->port.icount.parity++; 297 else if (r1 & CRC_ERR) 298 uap->port.icount.frame++; 299 if (r1 & Rx_OVR) 300 uap->port.icount.overrun++; 301 r1 &= uap->port.read_status_mask; 302 if (r1 & BRK_ABRT) 303 flag = TTY_BREAK; 304 else if (r1 & PAR_ERR) 305 flag = TTY_PARITY; 306 else if (r1 & CRC_ERR) 307 flag = TTY_FRAME; 308 } 309 310 if (uap->port.ignore_status_mask == 0xff || 311 (r1 & uap->port.ignore_status_mask) == 0) { 312 tty_insert_flip_char(tty, ch, flag); 313 } 314 if (r1 & Rx_OVR) 315 tty_insert_flip_char(tty, 0, TTY_OVERRUN); 316 next_char: 317 /* We can get stuck in an infinite loop getting char 0 when the 318 * line is in a wrong HW state, we break that here. 319 * When that happens, I disable the receive side of the driver. 320 * Note that what I've been experiencing is a real irq loop where 321 * I'm getting flooded regardless of the actual port speed. 322 * Something strange is going on with the HW 323 */ 324 if ((++loops) > 1000) 325 goto flood; 326 ch = read_zsreg(uap, R0); 327 if (!(ch & Rx_CH_AV)) 328 break; 329 } 330 331 return tty; 332 flood: 333 pmz_interrupt_control(uap, 0); 334 pmz_error("pmz: rx irq flood !\n"); 335 return tty; 336} 337 338static void pmz_status_handle(struct uart_pmac_port *uap) 339{ 340 unsigned char status; 341 342 status = read_zsreg(uap, R0); 343 write_zsreg(uap, R0, RES_EXT_INT); 344 zssync(uap); 345 346 if (ZS_IS_OPEN(uap) && ZS_WANTS_MODEM_STATUS(uap)) { 347 if (status & SYNC_HUNT) 348 uap->port.icount.dsr++; 349 350 /* The Zilog just gives us an interrupt when DCD/CTS/etc. change. 351 * But it does not tell us which bit has changed, we have to keep 352 * track of this ourselves. 353 * The CTS input is inverted for some reason. -- paulus 354 */ 355 if ((status ^ uap->prev_status) & DCD) 356 uart_handle_dcd_change(&uap->port, 357 (status & DCD)); 358 if ((status ^ uap->prev_status) & CTS) 359 uart_handle_cts_change(&uap->port, 360 !(status & CTS)); 361 362 wake_up_interruptible(&uap->port.state->port.delta_msr_wait); 363 } 364 365 if (status & BRK_ABRT) 366 uap->flags |= PMACZILOG_FLAG_BREAK; 367 368 uap->prev_status = status; 369} 370 371static void pmz_transmit_chars(struct uart_pmac_port *uap) 372{ 373 struct circ_buf *xmit; 374 375 if (ZS_IS_CONS(uap)) { 376 unsigned char status = read_zsreg(uap, R0); 377 378 /* TX still busy? Just wait for the next TX done interrupt. 379 * 380 * It can occur because of how we do serial console writes. It would 381 * be nice to transmit console writes just like we normally would for 382 * a TTY line. (ie. buffered and TX interrupt driven). That is not 383 * easy because console writes cannot sleep. One solution might be 384 * to poll on enough port->xmit space becoming free. -DaveM 385 */ 386 if (!(status & Tx_BUF_EMP)) 387 return; 388 } 389 390 uap->flags &= ~PMACZILOG_FLAG_TX_ACTIVE; 391 392 if (ZS_REGS_HELD(uap)) { 393 pmz_load_zsregs(uap, uap->curregs); 394 uap->flags &= ~PMACZILOG_FLAG_REGS_HELD; 395 } 396 397 if (ZS_TX_STOPPED(uap)) { 398 uap->flags &= ~PMACZILOG_FLAG_TX_STOPPED; 399 goto ack_tx_int; 400 } 401 402 /* Under some circumstances, we see interrupts reported for 403 * a closed channel. The interrupt mask in R1 is clear, but 404 * R3 still signals the interrupts and we see them when taking 405 * an interrupt for the other channel (this could be a qemu 406 * bug but since the ESCC doc doesn't specify precsiely whether 407 * R3 interrup status bits are masked by R1 interrupt enable 408 * bits, better safe than sorry). --BenH. 409 */ 410 if (!ZS_IS_OPEN(uap)) 411 goto ack_tx_int; 412 413 if (uap->port.x_char) { 414 uap->flags |= PMACZILOG_FLAG_TX_ACTIVE; 415 write_zsdata(uap, uap->port.x_char); 416 zssync(uap); 417 uap->port.icount.tx++; 418 uap->port.x_char = 0; 419 return; 420 } 421 422 if (uap->port.state == NULL) 423 goto ack_tx_int; 424 xmit = &uap->port.state->xmit; 425 if (uart_circ_empty(xmit)) { 426 uart_write_wakeup(&uap->port); 427 goto ack_tx_int; 428 } 429 if (uart_tx_stopped(&uap->port)) 430 goto ack_tx_int; 431 432 uap->flags |= PMACZILOG_FLAG_TX_ACTIVE; 433 write_zsdata(uap, xmit->buf[xmit->tail]); 434 zssync(uap); 435 436 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 437 uap->port.icount.tx++; 438 439 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 440 uart_write_wakeup(&uap->port); 441 442 return; 443 444ack_tx_int: 445 write_zsreg(uap, R0, RES_Tx_P); 446 zssync(uap); 447} 448 449/* Hrm... we register that twice, fixme later.... */ 450static irqreturn_t pmz_interrupt(int irq, void *dev_id) 451{ 452 struct uart_pmac_port *uap = dev_id; 453 struct uart_pmac_port *uap_a; 454 struct uart_pmac_port *uap_b; 455 int rc = IRQ_NONE; 456 struct tty_struct *tty; 457 u8 r3; 458 459 uap_a = pmz_get_port_A(uap); 460 uap_b = uap_a->mate; 461 462 spin_lock(&uap_a->port.lock); 463 r3 = read_zsreg(uap_a, R3); 464 465#ifdef DEBUG_HARD 466 pmz_debug("irq, r3: %x\n", r3); 467#endif 468 /* Channel A */ 469 tty = NULL; 470 if (r3 & (CHAEXT | CHATxIP | CHARxIP)) { 471 if (!ZS_IS_OPEN(uap_a)) { 472 pmz_debug("ChanA interrupt while not open !\n"); 473 goto skip_a; 474 } 475 write_zsreg(uap_a, R0, RES_H_IUS); 476 zssync(uap_a); 477 if (r3 & CHAEXT) 478 pmz_status_handle(uap_a); 479 if (r3 & CHARxIP) 480 tty = pmz_receive_chars(uap_a); 481 if (r3 & CHATxIP) 482 pmz_transmit_chars(uap_a); 483 rc = IRQ_HANDLED; 484 } 485 skip_a: 486 spin_unlock(&uap_a->port.lock); 487 if (tty != NULL) 488 tty_flip_buffer_push(tty); 489 490 if (!uap_b) 491 goto out; 492 493 spin_lock(&uap_b->port.lock); 494 tty = NULL; 495 if (r3 & (CHBEXT | CHBTxIP | CHBRxIP)) { 496 if (!ZS_IS_OPEN(uap_b)) { 497 pmz_debug("ChanB interrupt while not open !\n"); 498 goto skip_b; 499 } 500 write_zsreg(uap_b, R0, RES_H_IUS); 501 zssync(uap_b); 502 if (r3 & CHBEXT) 503 pmz_status_handle(uap_b); 504 if (r3 & CHBRxIP) 505 tty = pmz_receive_chars(uap_b); 506 if (r3 & CHBTxIP) 507 pmz_transmit_chars(uap_b); 508 rc = IRQ_HANDLED; 509 } 510 skip_b: 511 spin_unlock(&uap_b->port.lock); 512 if (tty != NULL) 513 tty_flip_buffer_push(tty); 514 515 out: 516 return rc; 517} 518 519/* 520 * Peek the status register, lock not held by caller 521 */ 522static inline u8 pmz_peek_status(struct uart_pmac_port *uap) 523{ 524 unsigned long flags; 525 u8 status; 526 527 spin_lock_irqsave(&uap->port.lock, flags); 528 status = read_zsreg(uap, R0); 529 spin_unlock_irqrestore(&uap->port.lock, flags); 530 531 return status; 532} 533 534/* 535 * Check if transmitter is empty 536 * The port lock is not held. 537 */ 538static unsigned int pmz_tx_empty(struct uart_port *port) 539{ 540 unsigned char status; 541 542 status = pmz_peek_status(to_pmz(port)); 543 if (status & Tx_BUF_EMP) 544 return TIOCSER_TEMT; 545 return 0; 546} 547 548/* 549 * Set Modem Control (RTS & DTR) bits 550 * The port lock is held and interrupts are disabled. 551 * Note: Shall we really filter out RTS on external ports or 552 * should that be dealt at higher level only ? 553 */ 554static void pmz_set_mctrl(struct uart_port *port, unsigned int mctrl) 555{ 556 struct uart_pmac_port *uap = to_pmz(port); 557 unsigned char set_bits, clear_bits; 558 559 /* Do nothing for irda for now... */ 560 if (ZS_IS_IRDA(uap)) 561 return; 562 /* We get called during boot with a port not up yet */ 563 if (!(ZS_IS_OPEN(uap) || ZS_IS_CONS(uap))) 564 return; 565 566 set_bits = clear_bits = 0; 567 568 if (ZS_IS_INTMODEM(uap)) { 569 if (mctrl & TIOCM_RTS) 570 set_bits |= RTS; 571 else 572 clear_bits |= RTS; 573 } 574 if (mctrl & TIOCM_DTR) 575 set_bits |= DTR; 576 else 577 clear_bits |= DTR; 578 579 /* NOTE: Not subject to 'transmitter active' rule. */ 580 uap->curregs[R5] |= set_bits; 581 uap->curregs[R5] &= ~clear_bits; 582 583 write_zsreg(uap, R5, uap->curregs[R5]); 584 pmz_debug("pmz_set_mctrl: set bits: %x, clear bits: %x -> %x\n", 585 set_bits, clear_bits, uap->curregs[R5]); 586 zssync(uap); 587} 588 589/* 590 * Get Modem Control bits (only the input ones, the core will 591 * or that with a cached value of the control ones) 592 * The port lock is held and interrupts are disabled. 593 */ 594static unsigned int pmz_get_mctrl(struct uart_port *port) 595{ 596 struct uart_pmac_port *uap = to_pmz(port); 597 unsigned char status; 598 unsigned int ret; 599 600 status = read_zsreg(uap, R0); 601 602 ret = 0; 603 if (status & DCD) 604 ret |= TIOCM_CAR; 605 if (status & SYNC_HUNT) 606 ret |= TIOCM_DSR; 607 if (!(status & CTS)) 608 ret |= TIOCM_CTS; 609 610 return ret; 611} 612 613/* 614 * Stop TX side. Dealt like sunzilog at next Tx interrupt, 615 * though for DMA, we will have to do a bit more. 616 * The port lock is held and interrupts are disabled. 617 */ 618static void pmz_stop_tx(struct uart_port *port) 619{ 620 to_pmz(port)->flags |= PMACZILOG_FLAG_TX_STOPPED; 621} 622 623/* 624 * Kick the Tx side. 625 * The port lock is held and interrupts are disabled. 626 */ 627static void pmz_start_tx(struct uart_port *port) 628{ 629 struct uart_pmac_port *uap = to_pmz(port); 630 unsigned char status; 631 632 pmz_debug("pmz: start_tx()\n"); 633 634 uap->flags |= PMACZILOG_FLAG_TX_ACTIVE; 635 uap->flags &= ~PMACZILOG_FLAG_TX_STOPPED; 636 637 status = read_zsreg(uap, R0); 638 639 /* TX busy? Just wait for the TX done interrupt. */ 640 if (!(status & Tx_BUF_EMP)) 641 return; 642 643 /* Send the first character to jump-start the TX done 644 * IRQ sending engine. 645 */ 646 if (port->x_char) { 647 write_zsdata(uap, port->x_char); 648 zssync(uap); 649 port->icount.tx++; 650 port->x_char = 0; 651 } else { 652 struct circ_buf *xmit = &port->state->xmit; 653 654 write_zsdata(uap, xmit->buf[xmit->tail]); 655 zssync(uap); 656 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); 657 port->icount.tx++; 658 659 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) 660 uart_write_wakeup(&uap->port); 661 } 662 pmz_debug("pmz: start_tx() done.\n"); 663} 664 665/* 666 * Stop Rx side, basically disable emitting of 667 * Rx interrupts on the port. We don't disable the rx 668 * side of the chip proper though 669 * The port lock is held. 670 */ 671static void pmz_stop_rx(struct uart_port *port) 672{ 673 struct uart_pmac_port *uap = to_pmz(port); 674 675 pmz_debug("pmz: stop_rx()()\n"); 676 677 /* Disable all RX interrupts. */ 678 uap->curregs[R1] &= ~RxINT_MASK; 679 pmz_maybe_update_regs(uap); 680 681 pmz_debug("pmz: stop_rx() done.\n"); 682} 683 684/* 685 * Enable modem status change interrupts 686 * The port lock is held. 687 */ 688static void pmz_enable_ms(struct uart_port *port) 689{ 690 struct uart_pmac_port *uap = to_pmz(port); 691 unsigned char new_reg; 692 693 if (ZS_IS_IRDA(uap)) 694 return; 695 new_reg = uap->curregs[R15] | (DCDIE | SYNCIE | CTSIE); 696 if (new_reg != uap->curregs[R15]) { 697 uap->curregs[R15] = new_reg; 698 699 /* NOTE: Not subject to 'transmitter active' rule. */ 700 write_zsreg(uap, R15, uap->curregs[R15]); 701 } 702} 703 704/* 705 * Control break state emission 706 * The port lock is not held. 707 */ 708static void pmz_break_ctl(struct uart_port *port, int break_state) 709{ 710 struct uart_pmac_port *uap = to_pmz(port); 711 unsigned char set_bits, clear_bits, new_reg; 712 unsigned long flags; 713 714 set_bits = clear_bits = 0; 715 716 if (break_state) 717 set_bits |= SND_BRK; 718 else 719 clear_bits |= SND_BRK; 720 721 spin_lock_irqsave(&port->lock, flags); 722 723 new_reg = (uap->curregs[R5] | set_bits) & ~clear_bits; 724 if (new_reg != uap->curregs[R5]) { 725 uap->curregs[R5] = new_reg; 726 write_zsreg(uap, R5, uap->curregs[R5]); 727 } 728 729 spin_unlock_irqrestore(&port->lock, flags); 730} 731 732#ifdef CONFIG_PPC_PMAC 733 734/* 735 * Turn power on or off to the SCC and associated stuff 736 * (port drivers, modem, IR port, etc.) 737 * Returns the number of milliseconds we should wait before 738 * trying to use the port. 739 */ 740static int pmz_set_scc_power(struct uart_pmac_port *uap, int state) 741{ 742 int delay = 0; 743 int rc; 744 745 if (state) { 746 rc = pmac_call_feature( 747 PMAC_FTR_SCC_ENABLE, uap->node, uap->port_type, 1); 748 pmz_debug("port power on result: %d\n", rc); 749 if (ZS_IS_INTMODEM(uap)) { 750 rc = pmac_call_feature( 751 PMAC_FTR_MODEM_ENABLE, uap->node, 0, 1); 752 delay = 2500; /* wait for 2.5s before using */ 753 pmz_debug("modem power result: %d\n", rc); 754 } 755 } else { 756 /* TODO: Make that depend on a timer, don't power down 757 * immediately 758 */ 759 if (ZS_IS_INTMODEM(uap)) { 760 rc = pmac_call_feature( 761 PMAC_FTR_MODEM_ENABLE, uap->node, 0, 0); 762 pmz_debug("port power off result: %d\n", rc); 763 } 764 pmac_call_feature(PMAC_FTR_SCC_ENABLE, uap->node, uap->port_type, 0); 765 } 766 return delay; 767} 768 769#else 770 771static int pmz_set_scc_power(struct uart_pmac_port *uap, int state) 772{ 773 return 0; 774} 775 776#endif /* !CONFIG_PPC_PMAC */ 777 778/* 779 * FixZeroBug....Works around a bug in the SCC receiving channel. 780 * Inspired from Darwin code, 15 Sept. 2000 -DanM 781 * 782 * The following sequence prevents a problem that is seen with O'Hare ASICs 783 * (most versions -- also with some Heathrow and Hydra ASICs) where a zero 784 * at the input to the receiver becomes 'stuck' and locks up the receiver. 785 * This problem can occur as a result of a zero bit at the receiver input 786 * coincident with any of the following events: 787 * 788 * The SCC is initialized (hardware or software). 789 * A framing error is detected. 790 * The clocking option changes from synchronous or X1 asynchronous 791 * clocking to X16, X32, or X64 asynchronous clocking. 792 * The decoding mode is changed among NRZ, NRZI, FM0, or FM1. 793 * 794 * This workaround attempts to recover from the lockup condition by placing 795 * the SCC in synchronous loopback mode with a fast clock before programming 796 * any of the asynchronous modes. 797 */ 798static void pmz_fix_zero_bug_scc(struct uart_pmac_port *uap) 799{ 800 write_zsreg(uap, 9, ZS_IS_CHANNEL_A(uap) ? CHRA : CHRB); 801 zssync(uap); 802 udelay(10); 803 write_zsreg(uap, 9, (ZS_IS_CHANNEL_A(uap) ? CHRA : CHRB) | NV); 804 zssync(uap); 805 806 write_zsreg(uap, 4, X1CLK | MONSYNC); 807 write_zsreg(uap, 3, Rx8); 808 write_zsreg(uap, 5, Tx8 | RTS); 809 write_zsreg(uap, 9, NV); /* Didn't we already do this? */ 810 write_zsreg(uap, 11, RCBR | TCBR); 811 write_zsreg(uap, 12, 0); 812 write_zsreg(uap, 13, 0); 813 write_zsreg(uap, 14, (LOOPBAK | BRSRC)); 814 write_zsreg(uap, 14, (LOOPBAK | BRSRC | BRENAB)); 815 write_zsreg(uap, 3, Rx8 | RxENABLE); 816 write_zsreg(uap, 0, RES_EXT_INT); 817 write_zsreg(uap, 0, RES_EXT_INT); 818 write_zsreg(uap, 0, RES_EXT_INT); /* to kill some time */ 819 820 /* The channel should be OK now, but it is probably receiving 821 * loopback garbage. 822 * Switch to asynchronous mode, disable the receiver, 823 * and discard everything in the receive buffer. 824 */ 825 write_zsreg(uap, 9, NV); 826 write_zsreg(uap, 4, X16CLK | SB_MASK); 827 write_zsreg(uap, 3, Rx8); 828 829 while (read_zsreg(uap, 0) & Rx_CH_AV) { 830 (void)read_zsreg(uap, 8); 831 write_zsreg(uap, 0, RES_EXT_INT); 832 write_zsreg(uap, 0, ERR_RES); 833 } 834} 835 836/* 837 * Real startup routine, powers up the hardware and sets up 838 * the SCC. Returns a delay in ms where you need to wait before 839 * actually using the port, this is typically the internal modem 840 * powerup delay. This routine expect the lock to be taken. 841 */ 842static int __pmz_startup(struct uart_pmac_port *uap) 843{ 844 int pwr_delay = 0; 845 846 memset(&uap->curregs, 0, sizeof(uap->curregs)); 847 848 /* Power up the SCC & underlying hardware (modem/irda) */ 849 pwr_delay = pmz_set_scc_power(uap, 1); 850 851 /* Nice buggy HW ... */ 852 pmz_fix_zero_bug_scc(uap); 853 854 /* Reset the channel */ 855 uap->curregs[R9] = 0; 856 write_zsreg(uap, 9, ZS_IS_CHANNEL_A(uap) ? CHRA : CHRB); 857 zssync(uap); 858 udelay(10); 859 write_zsreg(uap, 9, 0); 860 zssync(uap); 861 862 /* Clear the interrupt registers */ 863 write_zsreg(uap, R1, 0); 864 write_zsreg(uap, R0, ERR_RES); 865 write_zsreg(uap, R0, ERR_RES); 866 write_zsreg(uap, R0, RES_H_IUS); 867 write_zsreg(uap, R0, RES_H_IUS); 868 869 /* Setup some valid baud rate */ 870 uap->curregs[R4] = X16CLK | SB1; 871 uap->curregs[R3] = Rx8; 872 uap->curregs[R5] = Tx8 | RTS; 873 if (!ZS_IS_IRDA(uap)) 874 uap->curregs[R5] |= DTR; 875 uap->curregs[R12] = 0; 876 uap->curregs[R13] = 0; 877 uap->curregs[R14] = BRENAB; 878 879 /* Clear handshaking, enable BREAK interrupts */ 880 uap->curregs[R15] = BRKIE; 881 882 /* Master interrupt enable */ 883 uap->curregs[R9] |= NV | MIE; 884 885 pmz_load_zsregs(uap, uap->curregs); 886 887 /* Enable receiver and transmitter. */ 888 write_zsreg(uap, R3, uap->curregs[R3] |= RxENABLE); 889 write_zsreg(uap, R5, uap->curregs[R5] |= TxENABLE); 890 891 /* Remember status for DCD/CTS changes */ 892 uap->prev_status = read_zsreg(uap, R0); 893 894 return pwr_delay; 895} 896 897static void pmz_irda_reset(struct uart_pmac_port *uap) 898{ 899 unsigned long flags; 900 901 spin_lock_irqsave(&uap->port.lock, flags); 902 uap->curregs[R5] |= DTR; 903 write_zsreg(uap, R5, uap->curregs[R5]); 904 zssync(uap); 905 spin_unlock_irqrestore(&uap->port.lock, flags); 906 msleep(110); 907 908 spin_lock_irqsave(&uap->port.lock, flags); 909 uap->curregs[R5] &= ~DTR; 910 write_zsreg(uap, R5, uap->curregs[R5]); 911 zssync(uap); 912 spin_unlock_irqrestore(&uap->port.lock, flags); 913 msleep(10); 914} 915 916/* 917 * This is the "normal" startup routine, using the above one 918 * wrapped with the lock and doing a schedule delay 919 */ 920static int pmz_startup(struct uart_port *port) 921{ 922 struct uart_pmac_port *uap = to_pmz(port); 923 unsigned long flags; 924 int pwr_delay = 0; 925 926 pmz_debug("pmz: startup()\n"); 927 928 uap->flags |= PMACZILOG_FLAG_IS_OPEN; 929 930 /* A console is never powered down. Else, power up and 931 * initialize the chip 932 */ 933 if (!ZS_IS_CONS(uap)) { 934 spin_lock_irqsave(&port->lock, flags); 935 pwr_delay = __pmz_startup(uap); 936 spin_unlock_irqrestore(&port->lock, flags); 937 } 938 sprintf(uap->irq_name, PMACZILOG_NAME"%d", uap->port.line); 939 if (request_irq(uap->port.irq, pmz_interrupt, IRQF_SHARED, 940 uap->irq_name, uap)) { 941 pmz_error("Unable to register zs interrupt handler.\n"); 942 pmz_set_scc_power(uap, 0); 943 return -ENXIO; 944 } 945 946 /* Right now, we deal with delay by blocking here, I'll be 947 * smarter later on 948 */ 949 if (pwr_delay != 0) { 950 pmz_debug("pmz: delaying %d ms\n", pwr_delay); 951 msleep(pwr_delay); 952 } 953 954 /* IrDA reset is done now */ 955 if (ZS_IS_IRDA(uap)) 956 pmz_irda_reset(uap); 957 958 /* Enable interrupt requests for the channel */ 959 spin_lock_irqsave(&port->lock, flags); 960 pmz_interrupt_control(uap, 1); 961 spin_unlock_irqrestore(&port->lock, flags); 962 963 pmz_debug("pmz: startup() done.\n"); 964 965 return 0; 966} 967 968static void pmz_shutdown(struct uart_port *port) 969{ 970 struct uart_pmac_port *uap = to_pmz(port); 971 unsigned long flags; 972 973 pmz_debug("pmz: shutdown()\n"); 974 975 spin_lock_irqsave(&port->lock, flags); 976 977 /* Disable interrupt requests for the channel */ 978 pmz_interrupt_control(uap, 0); 979 980 if (!ZS_IS_CONS(uap)) { 981 /* Disable receiver and transmitter */ 982 uap->curregs[R3] &= ~RxENABLE; 983 uap->curregs[R5] &= ~TxENABLE; 984 985 /* Disable break assertion */ 986 uap->curregs[R5] &= ~SND_BRK; 987 pmz_maybe_update_regs(uap); 988 } 989 990 spin_unlock_irqrestore(&port->lock, flags); 991 992 /* Release interrupt handler */ 993 free_irq(uap->port.irq, uap); 994 995 spin_lock_irqsave(&port->lock, flags); 996 997 uap->flags &= ~PMACZILOG_FLAG_IS_OPEN; 998 999 if (!ZS_IS_CONS(uap)) 1000 pmz_set_scc_power(uap, 0); /* Shut the chip down */ 1001 1002 spin_unlock_irqrestore(&port->lock, flags); 1003 1004 pmz_debug("pmz: shutdown() done.\n"); 1005} 1006 1007/* Shared by TTY driver and serial console setup. The port lock is held 1008 * and local interrupts are disabled. 1009 */ 1010static void pmz_convert_to_zs(struct uart_pmac_port *uap, unsigned int cflag, 1011 unsigned int iflag, unsigned long baud) 1012{ 1013 int brg; 1014 1015 /* Switch to external clocking for IrDA high clock rates. That 1016 * code could be re-used for Midi interfaces with different 1017 * multipliers 1018 */ 1019 if (baud >= 115200 && ZS_IS_IRDA(uap)) { 1020 uap->curregs[R4] = X1CLK; 1021 uap->curregs[R11] = RCTRxCP | TCTRxCP; 1022 uap->curregs[R14] = 0; /* BRG off */ 1023 uap->curregs[R12] = 0; 1024 uap->curregs[R13] = 0; 1025 uap->flags |= PMACZILOG_FLAG_IS_EXTCLK; 1026 } else { 1027 switch (baud) { 1028 case ZS_CLOCK/16: /* 230400 */ 1029 uap->curregs[R4] = X16CLK; 1030 uap->curregs[R11] = 0; 1031 uap->curregs[R14] = 0; 1032 break; 1033 case ZS_CLOCK/32: /* 115200 */ 1034 uap->curregs[R4] = X32CLK; 1035 uap->curregs[R11] = 0; 1036 uap->curregs[R14] = 0; 1037 break; 1038 default: 1039 uap->curregs[R4] = X16CLK; 1040 uap->curregs[R11] = TCBR | RCBR; 1041 brg = BPS_TO_BRG(baud, ZS_CLOCK / 16); 1042 uap->curregs[R12] = (brg & 255); 1043 uap->curregs[R13] = ((brg >> 8) & 255); 1044 uap->curregs[R14] = BRENAB; 1045 } 1046 uap->flags &= ~PMACZILOG_FLAG_IS_EXTCLK; 1047 } 1048 1049 /* Character size, stop bits, and parity. */ 1050 uap->curregs[3] &= ~RxN_MASK; 1051 uap->curregs[5] &= ~TxN_MASK; 1052 1053 switch (cflag & CSIZE) { 1054 case CS5: 1055 uap->curregs[3] |= Rx5; 1056 uap->curregs[5] |= Tx5; 1057 uap->parity_mask = 0x1f; 1058 break; 1059 case CS6: 1060 uap->curregs[3] |= Rx6; 1061 uap->curregs[5] |= Tx6; 1062 uap->parity_mask = 0x3f; 1063 break; 1064 case CS7: 1065 uap->curregs[3] |= Rx7; 1066 uap->curregs[5] |= Tx7; 1067 uap->parity_mask = 0x7f; 1068 break; 1069 case CS8: 1070 default: 1071 uap->curregs[3] |= Rx8; 1072 uap->curregs[5] |= Tx8; 1073 uap->parity_mask = 0xff; 1074 break; 1075 }; 1076 uap->curregs[4] &= ~(SB_MASK); 1077 if (cflag & CSTOPB) 1078 uap->curregs[4] |= SB2; 1079 else 1080 uap->curregs[4] |= SB1; 1081 if (cflag & PARENB) 1082 uap->curregs[4] |= PAR_ENAB; 1083 else 1084 uap->curregs[4] &= ~PAR_ENAB; 1085 if (!(cflag & PARODD)) 1086 uap->curregs[4] |= PAR_EVEN; 1087 else 1088 uap->curregs[4] &= ~PAR_EVEN; 1089 1090 uap->port.read_status_mask = Rx_OVR; 1091 if (iflag & INPCK) 1092 uap->port.read_status_mask |= CRC_ERR | PAR_ERR; 1093 if (iflag & (BRKINT | PARMRK)) 1094 uap->port.read_status_mask |= BRK_ABRT; 1095 1096 uap->port.ignore_status_mask = 0; 1097 if (iflag & IGNPAR) 1098 uap->port.ignore_status_mask |= CRC_ERR | PAR_ERR; 1099 if (iflag & IGNBRK) { 1100 uap->port.ignore_status_mask |= BRK_ABRT; 1101 if (iflag & IGNPAR) 1102 uap->port.ignore_status_mask |= Rx_OVR; 1103 } 1104 1105 if ((cflag & CREAD) == 0) 1106 uap->port.ignore_status_mask = 0xff; 1107} 1108 1109 1110/* 1111 * Set the irda codec on the imac to the specified baud rate. 1112 */ 1113static void pmz_irda_setup(struct uart_pmac_port *uap, unsigned long *baud) 1114{ 1115 u8 cmdbyte; 1116 int t, version; 1117 1118 switch (*baud) { 1119 /* SIR modes */ 1120 case 2400: 1121 cmdbyte = 0x53; 1122 break; 1123 case 4800: 1124 cmdbyte = 0x52; 1125 break; 1126 case 9600: 1127 cmdbyte = 0x51; 1128 break; 1129 case 19200: 1130 cmdbyte = 0x50; 1131 break; 1132 case 38400: 1133 cmdbyte = 0x4f; 1134 break; 1135 case 57600: 1136 cmdbyte = 0x4e; 1137 break; 1138 case 115200: 1139 cmdbyte = 0x4d; 1140 break; 1141 /* The FIR modes aren't really supported at this point, how 1142 * do we select the speed ? via the FCR on KeyLargo ? 1143 */ 1144 case 1152000: 1145 cmdbyte = 0; 1146 break; 1147 case 4000000: 1148 cmdbyte = 0; 1149 break; 1150 default: /* 9600 */ 1151 cmdbyte = 0x51; 1152 *baud = 9600; 1153 break; 1154 } 1155 1156 /* Wait for transmitter to drain */ 1157 t = 10000; 1158 while ((read_zsreg(uap, R0) & Tx_BUF_EMP) == 0 1159 || (read_zsreg(uap, R1) & ALL_SNT) == 0) { 1160 if (--t <= 0) { 1161 pmz_error("transmitter didn't drain\n"); 1162 return; 1163 } 1164 udelay(10); 1165 } 1166 1167 /* Drain the receiver too */ 1168 t = 100; 1169 (void)read_zsdata(uap); 1170 (void)read_zsdata(uap); 1171 (void)read_zsdata(uap); 1172 mdelay(10); 1173 while (read_zsreg(uap, R0) & Rx_CH_AV) { 1174 read_zsdata(uap); 1175 mdelay(10); 1176 if (--t <= 0) { 1177 pmz_error("receiver didn't drain\n"); 1178 return; 1179 } 1180 } 1181 1182 /* Switch to command mode */ 1183 uap->curregs[R5] |= DTR; 1184 write_zsreg(uap, R5, uap->curregs[R5]); 1185 zssync(uap); 1186 mdelay(1); 1187 1188 /* Switch SCC to 19200 */ 1189 pmz_convert_to_zs(uap, CS8, 0, 19200); 1190 pmz_load_zsregs(uap, uap->curregs); 1191 mdelay(1); 1192 1193 /* Write get_version command byte */ 1194 write_zsdata(uap, 1); 1195 t = 5000; 1196 while ((read_zsreg(uap, R0) & Rx_CH_AV) == 0) { 1197 if (--t <= 0) { 1198 pmz_error("irda_setup timed out on get_version byte\n"); 1199 goto out; 1200 } 1201 udelay(10); 1202 } 1203 version = read_zsdata(uap); 1204 1205 if (version < 4) { 1206 pmz_info("IrDA: dongle version %d not supported\n", version); 1207 goto out; 1208 } 1209 1210 /* Send speed mode */ 1211 write_zsdata(uap, cmdbyte); 1212 t = 5000; 1213 while ((read_zsreg(uap, R0) & Rx_CH_AV) == 0) { 1214 if (--t <= 0) { 1215 pmz_error("irda_setup timed out on speed mode byte\n"); 1216 goto out; 1217 } 1218 udelay(10); 1219 } 1220 t = read_zsdata(uap); 1221 if (t != cmdbyte) 1222 pmz_error("irda_setup speed mode byte = %x (%x)\n", t, cmdbyte); 1223 1224 pmz_info("IrDA setup for %ld bps, dongle version: %d\n", 1225 *baud, version); 1226 1227 (void)read_zsdata(uap); 1228 (void)read_zsdata(uap); 1229 (void)read_zsdata(uap); 1230 1231 out: 1232 /* Switch back to data mode */ 1233 uap->curregs[R5] &= ~DTR; 1234 write_zsreg(uap, R5, uap->curregs[R5]); 1235 zssync(uap); 1236 1237 (void)read_zsdata(uap); 1238 (void)read_zsdata(uap); 1239 (void)read_zsdata(uap); 1240} 1241 1242 1243static void __pmz_set_termios(struct uart_port *port, struct ktermios *termios, 1244 struct ktermios *old) 1245{ 1246 struct uart_pmac_port *uap = to_pmz(port); 1247 unsigned long baud; 1248 1249 pmz_debug("pmz: set_termios()\n"); 1250 1251 memcpy(&uap->termios_cache, termios, sizeof(struct ktermios)); 1252 1253 /* XXX Check which revs of machines actually allow 1 and 4Mb speeds 1254 * on the IR dongle. Note that the IRTTY driver currently doesn't know 1255 * about the FIR mode and high speed modes. So these are unused. For 1256 * implementing proper support for these, we should probably add some 1257 * DMA as well, at least on the Rx side, which isn't a simple thing 1258 * at this point. 1259 */ 1260 if (ZS_IS_IRDA(uap)) { 1261 /* Calc baud rate */ 1262 baud = uart_get_baud_rate(port, termios, old, 1200, 4000000); 1263 pmz_debug("pmz: switch IRDA to %ld bauds\n", baud); 1264 /* Cet the irda codec to the right rate */ 1265 pmz_irda_setup(uap, &baud); 1266 /* Set final baud rate */ 1267 pmz_convert_to_zs(uap, termios->c_cflag, termios->c_iflag, baud); 1268 pmz_load_zsregs(uap, uap->curregs); 1269 zssync(uap); 1270 } else { 1271 baud = uart_get_baud_rate(port, termios, old, 1200, 230400); 1272 pmz_convert_to_zs(uap, termios->c_cflag, termios->c_iflag, baud); 1273 /* Make sure modem status interrupts are correctly configured */ 1274 if (UART_ENABLE_MS(&uap->port, termios->c_cflag)) { 1275 uap->curregs[R15] |= DCDIE | SYNCIE | CTSIE; 1276 uap->flags |= PMACZILOG_FLAG_MODEM_STATUS; 1277 } else { 1278 uap->curregs[R15] &= ~(DCDIE | SYNCIE | CTSIE); 1279 uap->flags &= ~PMACZILOG_FLAG_MODEM_STATUS; 1280 } 1281 1282 /* Load registers to the chip */ 1283 pmz_maybe_update_regs(uap); 1284 } 1285 uart_update_timeout(port, termios->c_cflag, baud); 1286 1287 pmz_debug("pmz: set_termios() done.\n"); 1288} 1289 1290/* The port lock is not held. */ 1291static void pmz_set_termios(struct uart_port *port, struct ktermios *termios, 1292 struct ktermios *old) 1293{ 1294 struct uart_pmac_port *uap = to_pmz(port); 1295 unsigned long flags; 1296 1297 spin_lock_irqsave(&port->lock, flags); 1298 1299 /* Disable IRQs on the port */ 1300 pmz_interrupt_control(uap, 0); 1301 1302 /* Setup new port configuration */ 1303 __pmz_set_termios(port, termios, old); 1304 1305 /* Re-enable IRQs on the port */ 1306 if (ZS_IS_OPEN(uap)) 1307 pmz_interrupt_control(uap, 1); 1308 1309 spin_unlock_irqrestore(&port->lock, flags); 1310} 1311 1312static const char *pmz_type(struct uart_port *port) 1313{ 1314 struct uart_pmac_port *uap = to_pmz(port); 1315 1316 if (ZS_IS_IRDA(uap)) 1317 return "Z85c30 ESCC - Infrared port"; 1318 else if (ZS_IS_INTMODEM(uap)) 1319 return "Z85c30 ESCC - Internal modem"; 1320 return "Z85c30 ESCC - Serial port"; 1321} 1322 1323/* We do not request/release mappings of the registers here, this 1324 * happens at early serial probe time. 1325 */ 1326static void pmz_release_port(struct uart_port *port) 1327{ 1328} 1329 1330static int pmz_request_port(struct uart_port *port) 1331{ 1332 return 0; 1333} 1334 1335/* These do not need to do anything interesting either. */ 1336static void pmz_config_port(struct uart_port *port, int flags) 1337{ 1338} 1339 1340/* We do not support letting the user mess with the divisor, IRQ, etc. */ 1341static int pmz_verify_port(struct uart_port *port, struct serial_struct *ser) 1342{ 1343 return -EINVAL; 1344} 1345 1346#ifdef CONFIG_CONSOLE_POLL 1347 1348static int pmz_poll_get_char(struct uart_port *port) 1349{ 1350 struct uart_pmac_port *uap = (struct uart_pmac_port *)port; 1351 1352 while ((read_zsreg(uap, R0) & Rx_CH_AV) == 0) 1353 udelay(5); 1354 return read_zsdata(uap); 1355} 1356 1357static void pmz_poll_put_char(struct uart_port *port, unsigned char c) 1358{ 1359 struct uart_pmac_port *uap = (struct uart_pmac_port *)port; 1360 1361 /* Wait for the transmit buffer to empty. */ 1362 while ((read_zsreg(uap, R0) & Tx_BUF_EMP) == 0) 1363 udelay(5); 1364 write_zsdata(uap, c); 1365} 1366 1367#endif /* CONFIG_CONSOLE_POLL */ 1368 1369static struct uart_ops pmz_pops = { 1370 .tx_empty = pmz_tx_empty, 1371 .set_mctrl = pmz_set_mctrl, 1372 .get_mctrl = pmz_get_mctrl, 1373 .stop_tx = pmz_stop_tx, 1374 .start_tx = pmz_start_tx, 1375 .stop_rx = pmz_stop_rx, 1376 .enable_ms = pmz_enable_ms, 1377 .break_ctl = pmz_break_ctl, 1378 .startup = pmz_startup, 1379 .shutdown = pmz_shutdown, 1380 .set_termios = pmz_set_termios, 1381 .type = pmz_type, 1382 .release_port = pmz_release_port, 1383 .request_port = pmz_request_port, 1384 .config_port = pmz_config_port, 1385 .verify_port = pmz_verify_port, 1386#ifdef CONFIG_CONSOLE_POLL 1387 .poll_get_char = pmz_poll_get_char, 1388 .poll_put_char = pmz_poll_put_char, 1389#endif 1390}; 1391 1392#ifdef CONFIG_PPC_PMAC 1393 1394/* 1395 * Setup one port structure after probing, HW is down at this point, 1396 * Unlike sunzilog, we don't need to pre-init the spinlock as we don't 1397 * register our console before uart_add_one_port() is called 1398 */ 1399static int __init pmz_init_port(struct uart_pmac_port *uap) 1400{ 1401 struct device_node *np = uap->node; 1402 const char *conn; 1403 const struct slot_names_prop { 1404 int count; 1405 char name[1]; 1406 } *slots; 1407 int len; 1408 struct resource r_ports, r_rxdma, r_txdma; 1409 1410 /* 1411 * Request & map chip registers 1412 */ 1413 if (of_address_to_resource(np, 0, &r_ports)) 1414 return -ENODEV; 1415 uap->port.mapbase = r_ports.start; 1416 uap->port.membase = ioremap(uap->port.mapbase, 0x1000); 1417 1418 uap->control_reg = uap->port.membase; 1419 uap->data_reg = uap->control_reg + 0x10; 1420 1421 /* 1422 * Request & map DBDMA registers 1423 */ 1424#ifdef HAS_DBDMA 1425 if (of_address_to_resource(np, 1, &r_txdma) == 0 && 1426 of_address_to_resource(np, 2, &r_rxdma) == 0) 1427 uap->flags |= PMACZILOG_FLAG_HAS_DMA; 1428#else 1429 memset(&r_txdma, 0, sizeof(struct resource)); 1430 memset(&r_rxdma, 0, sizeof(struct resource)); 1431#endif 1432 if (ZS_HAS_DMA(uap)) { 1433 uap->tx_dma_regs = ioremap(r_txdma.start, 0x100); 1434 if (uap->tx_dma_regs == NULL) { 1435 uap->flags &= ~PMACZILOG_FLAG_HAS_DMA; 1436 goto no_dma; 1437 } 1438 uap->rx_dma_regs = ioremap(r_rxdma.start, 0x100); 1439 if (uap->rx_dma_regs == NULL) { 1440 iounmap(uap->tx_dma_regs); 1441 uap->tx_dma_regs = NULL; 1442 uap->flags &= ~PMACZILOG_FLAG_HAS_DMA; 1443 goto no_dma; 1444 } 1445 uap->tx_dma_irq = irq_of_parse_and_map(np, 1); 1446 uap->rx_dma_irq = irq_of_parse_and_map(np, 2); 1447 } 1448no_dma: 1449 1450 /* 1451 * Detect port type 1452 */ 1453 if (of_device_is_compatible(np, "cobalt")) 1454 uap->flags |= PMACZILOG_FLAG_IS_INTMODEM; 1455 conn = of_get_property(np, "AAPL,connector", &len); 1456 if (conn && (strcmp(conn, "infrared") == 0)) 1457 uap->flags |= PMACZILOG_FLAG_IS_IRDA; 1458 uap->port_type = PMAC_SCC_ASYNC; 1459 /* 1999 Powerbook G3 has slot-names property instead */ 1460 slots = of_get_property(np, "slot-names", &len); 1461 if (slots && slots->count > 0) { 1462 if (strcmp(slots->name, "IrDA") == 0) 1463 uap->flags |= PMACZILOG_FLAG_IS_IRDA; 1464 else if (strcmp(slots->name, "Modem") == 0) 1465 uap->flags |= PMACZILOG_FLAG_IS_INTMODEM; 1466 } 1467 if (ZS_IS_IRDA(uap)) 1468 uap->port_type = PMAC_SCC_IRDA; 1469 if (ZS_IS_INTMODEM(uap)) { 1470 struct device_node* i2c_modem = 1471 of_find_node_by_name(NULL, "i2c-modem"); 1472 if (i2c_modem) { 1473 const char* mid = 1474 of_get_property(i2c_modem, "modem-id", NULL); 1475 if (mid) switch(*mid) { 1476 case 0x04 : 1477 case 0x05 : 1478 case 0x07 : 1479 case 0x08 : 1480 case 0x0b : 1481 case 0x0c : 1482 uap->port_type = PMAC_SCC_I2S1; 1483 } 1484 printk(KERN_INFO "pmac_zilog: i2c-modem detected, id: %d\n", 1485 mid ? (*mid) : 0); 1486 of_node_put(i2c_modem); 1487 } else { 1488 printk(KERN_INFO "pmac_zilog: serial modem detected\n"); 1489 } 1490 } 1491 1492 /* 1493 * Init remaining bits of "port" structure 1494 */ 1495 uap->port.iotype = UPIO_MEM; 1496 uap->port.irq = irq_of_parse_and_map(np, 0); 1497 uap->port.uartclk = ZS_CLOCK; 1498 uap->port.fifosize = 1; 1499 uap->port.ops = &pmz_pops; 1500 uap->port.type = PORT_PMAC_ZILOG; 1501 uap->port.flags = 0; 1502 1503 /* 1504 * Fixup for the port on Gatwick for which the device-tree has 1505 * missing interrupts. Normally, the macio_dev would contain 1506 * fixed up interrupt info, but we use the device-tree directly 1507 * here due to early probing so we need the fixup too. 1508 */ 1509 if (uap->port.irq == 0 && 1510 np->parent && np->parent->parent && 1511 of_device_is_compatible(np->parent->parent, "gatwick")) { 1512 /* IRQs on gatwick are offset by 64 */ 1513 uap->port.irq = irq_create_mapping(NULL, 64 + 15); 1514 uap->tx_dma_irq = irq_create_mapping(NULL, 64 + 4); 1515 uap->rx_dma_irq = irq_create_mapping(NULL, 64 + 5); 1516 } 1517 1518 /* Setup some valid baud rate information in the register 1519 * shadows so we don't write crap there before baud rate is 1520 * first initialized. 1521 */ 1522 pmz_convert_to_zs(uap, CS8, 0, 9600); 1523 1524 return 0; 1525} 1526 1527/* 1528 * Get rid of a port on module removal 1529 */ 1530static void pmz_dispose_port(struct uart_pmac_port *uap) 1531{ 1532 struct device_node *np; 1533 1534 np = uap->node; 1535 iounmap(uap->rx_dma_regs); 1536 iounmap(uap->tx_dma_regs); 1537 iounmap(uap->control_reg); 1538 uap->node = NULL; 1539 of_node_put(np); 1540 memset(uap, 0, sizeof(struct uart_pmac_port)); 1541} 1542 1543/* 1544 * Called upon match with an escc node in the device-tree. 1545 */ 1546static int pmz_attach(struct macio_dev *mdev, const struct of_device_id *match) 1547{ 1548 struct uart_pmac_port *uap; 1549 int i; 1550 1551 /* Iterate the pmz_ports array to find a matching entry 1552 */ 1553 for (i = 0; i < MAX_ZS_PORTS; i++) 1554 if (pmz_ports[i].node == mdev->ofdev.dev.of_node) 1555 break; 1556 if (i >= MAX_ZS_PORTS) 1557 return -ENODEV; 1558 1559 1560 uap = &pmz_ports[i]; 1561 uap->dev = mdev; 1562 uap->port.dev = &mdev->ofdev.dev; 1563 dev_set_drvdata(&mdev->ofdev.dev, uap); 1564 1565 /* We still activate the port even when failing to request resources 1566 * to work around bugs in ancient Apple device-trees 1567 */ 1568 if (macio_request_resources(uap->dev, "pmac_zilog")) 1569 printk(KERN_WARNING "%s: Failed to request resource" 1570 ", port still active\n", 1571 uap->node->name); 1572 else 1573 uap->flags |= PMACZILOG_FLAG_RSRC_REQUESTED; 1574 1575 return uart_add_one_port(&pmz_uart_reg, &uap->port); 1576} 1577 1578/* 1579 * That one should not be called, macio isn't really a hotswap device, 1580 * we don't expect one of those serial ports to go away... 1581 */ 1582static int pmz_detach(struct macio_dev *mdev) 1583{ 1584 struct uart_pmac_port *uap = dev_get_drvdata(&mdev->ofdev.dev); 1585 1586 if (!uap) 1587 return -ENODEV; 1588 1589 uart_remove_one_port(&pmz_uart_reg, &uap->port); 1590 1591 if (uap->flags & PMACZILOG_FLAG_RSRC_REQUESTED) { 1592 macio_release_resources(uap->dev); 1593 uap->flags &= ~PMACZILOG_FLAG_RSRC_REQUESTED; 1594 } 1595 dev_set_drvdata(&mdev->ofdev.dev, NULL); 1596 uap->dev = NULL; 1597 uap->port.dev = NULL; 1598 1599 return 0; 1600} 1601 1602 1603static int pmz_suspend(struct macio_dev *mdev, pm_message_t pm_state) 1604{ 1605 struct uart_pmac_port *uap = dev_get_drvdata(&mdev->ofdev.dev); 1606 1607 if (uap == NULL) { 1608 printk("HRM... pmz_suspend with NULL uap\n"); 1609 return 0; 1610 } 1611 1612 uart_suspend_port(&pmz_uart_reg, &uap->port); 1613 1614 return 0; 1615} 1616 1617 1618static int pmz_resume(struct macio_dev *mdev) 1619{ 1620 struct uart_pmac_port *uap = dev_get_drvdata(&mdev->ofdev.dev); 1621 1622 if (uap == NULL) 1623 return 0; 1624 1625 uart_resume_port(&pmz_uart_reg, &uap->port); 1626 1627 return 0; 1628} 1629 1630/* 1631 * Probe all ports in the system and build the ports array, we register 1632 * with the serial layer later, so we get a proper struct device which 1633 * allows the tty to attach properly. This is later than it used to be 1634 * but the tty layer really wants it that way. 1635 */ 1636static int __init pmz_probe(void) 1637{ 1638 struct device_node *node_p, *node_a, *node_b, *np; 1639 int count = 0; 1640 int rc; 1641 1642 /* 1643 * Find all escc chips in the system 1644 */ 1645 node_p = of_find_node_by_name(NULL, "escc"); 1646 while (node_p) { 1647 /* 1648 * First get channel A/B node pointers 1649 * 1650 * TODO: Add routines with proper locking to do that... 1651 */ 1652 node_a = node_b = NULL; 1653 for (np = NULL; (np = of_get_next_child(node_p, np)) != NULL;) { 1654 if (strncmp(np->name, "ch-a", 4) == 0) 1655 node_a = of_node_get(np); 1656 else if (strncmp(np->name, "ch-b", 4) == 0) 1657 node_b = of_node_get(np); 1658 } 1659 if (!node_a && !node_b) { 1660 of_node_put(node_a); 1661 of_node_put(node_b); 1662 printk(KERN_ERR "pmac_zilog: missing node %c for escc %s\n", 1663 (!node_a) ? 'a' : 'b', node_p->full_name); 1664 goto next; 1665 } 1666 1667 /* 1668 * Fill basic fields in the port structures 1669 */ 1670 if (node_b != NULL) { 1671 pmz_ports[count].mate = &pmz_ports[count+1]; 1672 pmz_ports[count+1].mate = &pmz_ports[count]; 1673 } 1674 pmz_ports[count].flags = PMACZILOG_FLAG_IS_CHANNEL_A; 1675 pmz_ports[count].node = node_a; 1676 pmz_ports[count+1].node = node_b; 1677 pmz_ports[count].port.line = count; 1678 pmz_ports[count+1].port.line = count+1; 1679 1680 /* 1681 * Setup the ports for real 1682 */ 1683 rc = pmz_init_port(&pmz_ports[count]); 1684 if (rc == 0 && node_b != NULL) 1685 rc = pmz_init_port(&pmz_ports[count+1]); 1686 if (rc != 0) { 1687 of_node_put(node_a); 1688 of_node_put(node_b); 1689 memset(&pmz_ports[count], 0, sizeof(struct uart_pmac_port)); 1690 memset(&pmz_ports[count+1], 0, sizeof(struct uart_pmac_port)); 1691 goto next; 1692 } 1693 count += 2; 1694next: 1695 node_p = of_find_node_by_name(node_p, "escc"); 1696 } 1697 pmz_ports_count = count; 1698 1699 return 0; 1700} 1701 1702#else 1703 1704extern struct platform_device scc_a_pdev, scc_b_pdev; 1705 1706static int __init pmz_init_port(struct uart_pmac_port *uap) 1707{ 1708 struct resource *r_ports; 1709 int irq; 1710 1711 r_ports = platform_get_resource(uap->pdev, IORESOURCE_MEM, 0); 1712 irq = platform_get_irq(uap->pdev, 0); 1713 if (!r_ports || !irq) 1714 return -ENODEV; 1715 1716 uap->port.mapbase = r_ports->start; 1717 uap->port.membase = (unsigned char __iomem *) r_ports->start; 1718 uap->port.iotype = UPIO_MEM; 1719 uap->port.irq = irq; 1720 uap->port.uartclk = ZS_CLOCK; 1721 uap->port.fifosize = 1; 1722 uap->port.ops = &pmz_pops; 1723 uap->port.type = PORT_PMAC_ZILOG; 1724 uap->port.flags = 0; 1725 1726 uap->control_reg = uap->port.membase; 1727 uap->data_reg = uap->control_reg + 4; 1728 uap->port_type = 0; 1729 1730 pmz_convert_to_zs(uap, CS8, 0, 9600); 1731 1732 return 0; 1733} 1734 1735static int __init pmz_probe(void) 1736{ 1737 int err; 1738 1739 pmz_ports_count = 0; 1740 1741 pmz_ports[0].port.line = 0; 1742 pmz_ports[0].flags = PMACZILOG_FLAG_IS_CHANNEL_A; 1743 pmz_ports[0].pdev = &scc_a_pdev; 1744 err = pmz_init_port(&pmz_ports[0]); 1745 if (err) 1746 return err; 1747 pmz_ports_count++; 1748 1749 pmz_ports[0].mate = &pmz_ports[1]; 1750 pmz_ports[1].mate = &pmz_ports[0]; 1751 pmz_ports[1].port.line = 1; 1752 pmz_ports[1].flags = 0; 1753 pmz_ports[1].pdev = &scc_b_pdev; 1754 err = pmz_init_port(&pmz_ports[1]); 1755 if (err) 1756 return err; 1757 pmz_ports_count++; 1758 1759 return 0; 1760} 1761 1762static void pmz_dispose_port(struct uart_pmac_port *uap) 1763{ 1764 memset(uap, 0, sizeof(struct uart_pmac_port)); 1765} 1766 1767static int __init pmz_attach(struct platform_device *pdev) 1768{ 1769 struct uart_pmac_port *uap; 1770 int i; 1771 1772 /* Iterate the pmz_ports array to find a matching entry */ 1773 for (i = 0; i < pmz_ports_count; i++) 1774 if (pmz_ports[i].pdev == pdev) 1775 break; 1776 if (i >= pmz_ports_count) 1777 return -ENODEV; 1778 1779 uap = &pmz_ports[i]; 1780 uap->port.dev = &pdev->dev; 1781 platform_set_drvdata(pdev, uap); 1782 1783 return uart_add_one_port(&pmz_uart_reg, &uap->port); 1784} 1785 1786static int __exit pmz_detach(struct platform_device *pdev) 1787{ 1788 struct uart_pmac_port *uap = platform_get_drvdata(pdev); 1789 1790 if (!uap) 1791 return -ENODEV; 1792 1793 uart_remove_one_port(&pmz_uart_reg, &uap->port); 1794 1795 platform_set_drvdata(pdev, NULL); 1796 uap->port.dev = NULL; 1797 1798 return 0; 1799} 1800 1801#endif /* !CONFIG_PPC_PMAC */ 1802 1803#ifdef CONFIG_SERIAL_PMACZILOG_CONSOLE 1804 1805static void pmz_console_write(struct console *con, const char *s, unsigned int count); 1806static int __init pmz_console_setup(struct console *co, char *options); 1807 1808static struct console pmz_console = { 1809 .name = PMACZILOG_NAME, 1810 .write = pmz_console_write, 1811 .device = uart_console_device, 1812 .setup = pmz_console_setup, 1813 .flags = CON_PRINTBUFFER, 1814 .index = -1, 1815 .data = &pmz_uart_reg, 1816}; 1817 1818#define PMACZILOG_CONSOLE &pmz_console 1819#else /* CONFIG_SERIAL_PMACZILOG_CONSOLE */ 1820#define PMACZILOG_CONSOLE (NULL) 1821#endif /* CONFIG_SERIAL_PMACZILOG_CONSOLE */ 1822 1823/* 1824 * Register the driver, console driver and ports with the serial 1825 * core 1826 */ 1827static int __init pmz_register(void) 1828{ 1829 pmz_uart_reg.nr = pmz_ports_count; 1830 pmz_uart_reg.cons = PMACZILOG_CONSOLE; 1831 1832 /* 1833 * Register this driver with the serial core 1834 */ 1835 return uart_register_driver(&pmz_uart_reg); 1836} 1837 1838#ifdef CONFIG_PPC_PMAC 1839 1840static struct of_device_id pmz_match[] = 1841{ 1842 { 1843 .name = "ch-a", 1844 }, 1845 { 1846 .name = "ch-b", 1847 }, 1848 {}, 1849}; 1850MODULE_DEVICE_TABLE (of, pmz_match); 1851 1852static struct macio_driver pmz_driver = { 1853 .driver = { 1854 .name = "pmac_zilog", 1855 .owner = THIS_MODULE, 1856 .of_match_table = pmz_match, 1857 }, 1858 .probe = pmz_attach, 1859 .remove = pmz_detach, 1860 .suspend = pmz_suspend, 1861 .resume = pmz_resume, 1862}; 1863 1864#else 1865 1866static struct platform_driver pmz_driver = { 1867 .remove = __exit_p(pmz_detach), 1868 .driver = { 1869 .name = "scc", 1870 .owner = THIS_MODULE, 1871 }, 1872}; 1873 1874#endif /* !CONFIG_PPC_PMAC */ 1875 1876static int __init init_pmz(void) 1877{ 1878 int rc, i; 1879 printk(KERN_INFO "%s\n", version); 1880 1881 /* 1882 * First, we need to do a direct OF-based probe pass. We 1883 * do that because we want serial console up before the 1884 * macio stuffs calls us back, and since that makes it 1885 * easier to pass the proper number of channels to 1886 * uart_register_driver() 1887 */ 1888 if (pmz_ports_count == 0) 1889 pmz_probe(); 1890 1891 /* 1892 * Bail early if no port found 1893 */ 1894 if (pmz_ports_count == 0) 1895 return -ENODEV; 1896 1897 /* 1898 * Now we register with the serial layer 1899 */ 1900 rc = pmz_register(); 1901 if (rc) { 1902 printk(KERN_ERR 1903 "pmac_zilog: Error registering serial device, disabling pmac_zilog.\n" 1904 "pmac_zilog: Did another serial driver already claim the minors?\n"); 1905 /* effectively "pmz_unprobe()" */ 1906 for (i=0; i < pmz_ports_count; i++) 1907 pmz_dispose_port(&pmz_ports[i]); 1908 return rc; 1909 } 1910 1911 /* 1912 * Then we register the macio driver itself 1913 */ 1914#ifdef CONFIG_PPC_PMAC 1915 return macio_register_driver(&pmz_driver); 1916#else 1917 return platform_driver_probe(&pmz_driver, pmz_attach); 1918#endif 1919} 1920 1921static void __exit exit_pmz(void) 1922{ 1923 int i; 1924 1925#ifdef CONFIG_PPC_PMAC 1926 /* Get rid of macio-driver (detach from macio) */ 1927 macio_unregister_driver(&pmz_driver); 1928#else 1929 platform_driver_unregister(&pmz_driver); 1930#endif 1931 1932 for (i = 0; i < pmz_ports_count; i++) { 1933 struct uart_pmac_port *uport = &pmz_ports[i]; 1934#ifdef CONFIG_PPC_PMAC 1935 if (uport->node != NULL) 1936 pmz_dispose_port(uport); 1937#else 1938 if (uport->pdev != NULL) 1939 pmz_dispose_port(uport); 1940#endif 1941 } 1942 /* Unregister UART driver */ 1943 uart_unregister_driver(&pmz_uart_reg); 1944} 1945 1946#ifdef CONFIG_SERIAL_PMACZILOG_CONSOLE 1947 1948static void pmz_console_putchar(struct uart_port *port, int ch) 1949{ 1950 struct uart_pmac_port *uap = (struct uart_pmac_port *)port; 1951 1952 /* Wait for the transmit buffer to empty. */ 1953 while ((read_zsreg(uap, R0) & Tx_BUF_EMP) == 0) 1954 udelay(5); 1955 write_zsdata(uap, ch); 1956} 1957 1958/* 1959 * Print a string to the serial port trying not to disturb 1960 * any possible real use of the port... 1961 */ 1962static void pmz_console_write(struct console *con, const char *s, unsigned int count) 1963{ 1964 struct uart_pmac_port *uap = &pmz_ports[con->index]; 1965 unsigned long flags; 1966 1967 spin_lock_irqsave(&uap->port.lock, flags); 1968 1969 /* Turn of interrupts and enable the transmitter. */ 1970 write_zsreg(uap, R1, uap->curregs[1] & ~TxINT_ENAB); 1971 write_zsreg(uap, R5, uap->curregs[5] | TxENABLE | RTS | DTR); 1972 1973 uart_console_write(&uap->port, s, count, pmz_console_putchar); 1974 1975 /* Restore the values in the registers. */ 1976 write_zsreg(uap, R1, uap->curregs[1]); 1977 /* Don't disable the transmitter. */ 1978 1979 spin_unlock_irqrestore(&uap->port.lock, flags); 1980} 1981 1982/* 1983 * Setup the serial console 1984 */ 1985static int __init pmz_console_setup(struct console *co, char *options) 1986{ 1987 struct uart_pmac_port *uap; 1988 struct uart_port *port; 1989 int baud = 38400; 1990 int bits = 8; 1991 int parity = 'n'; 1992 int flow = 'n'; 1993 unsigned long pwr_delay; 1994 1995 /* 1996 * XServe's default to 57600 bps 1997 */ 1998 if (of_machine_is_compatible("RackMac1,1") 1999 || of_machine_is_compatible("RackMac1,2") 2000 || of_machine_is_compatible("MacRISC4")) 2001 baud = 57600; 2002 2003 /* 2004 * Check whether an invalid uart number has been specified, and 2005 * if so, search for the first available port that does have 2006 * console support. 2007 */ 2008 if (co->index >= pmz_ports_count) 2009 co->index = 0; 2010 uap = &pmz_ports[co->index]; 2011#ifdef CONFIG_PPC_PMAC 2012 if (uap->node == NULL) 2013 return -ENODEV; 2014#else 2015 if (uap->pdev == NULL) 2016 return -ENODEV; 2017#endif 2018 port = &uap->port; 2019 2020 /* 2021 * Mark port as beeing a console 2022 */ 2023 uap->flags |= PMACZILOG_FLAG_IS_CONS; 2024 2025 /* 2026 * Temporary fix for uart layer who didn't setup the spinlock yet 2027 */ 2028 spin_lock_init(&port->lock); 2029 2030 /* 2031 * Enable the hardware 2032 */ 2033 pwr_delay = __pmz_startup(uap); 2034 if (pwr_delay) 2035 mdelay(pwr_delay); 2036 2037 if (options) 2038 uart_parse_options(options, &baud, &parity, &bits, &flow); 2039 2040 return uart_set_options(port, co, baud, parity, bits, flow); 2041} 2042 2043static int __init pmz_console_init(void) 2044{ 2045 /* Probe ports */ 2046 pmz_probe(); 2047 2048 /* TODO: Autoprobe console based on OF */ 2049 /* pmz_console.index = i; */ 2050 register_console(&pmz_console); 2051 2052 return 0; 2053 2054} 2055console_initcall(pmz_console_init); 2056#endif /* CONFIG_SERIAL_PMACZILOG_CONSOLE */ 2057 2058module_init(init_pmz); 2059module_exit(exit_pmz); 2060