1/* 2 * OHCI HCD (Host Controller Driver) for USB. 3 * 4 * (C) Copyright 1999 Roman Weissgaerber <weissg@vienna.at> 5 * (C) Copyright 2000-2002 David Brownell <dbrownell@users.sourceforge.net> 6 * (C) Copyright 2002 Hewlett-Packard Company 7 * 8 * Bus Glue for pxa27x 9 * 10 * Written by Christopher Hoover <ch@hpl.hp.com> 11 * Based on fragments of previous driver by Russell King et al. 12 * 13 * Modified for LH7A404 from ohci-sa1111.c 14 * by Durgesh Pattamatta <pattamattad@sharpsec.com> 15 * 16 * Modified for pxa27x from ohci-lh7a404.c 17 * by Nick Bane <nick@cecomputing.co.uk> 26-8-2004 18 * 19 * This file is licenced under the GPL. 20 */ 21 22#include <linux/device.h> 23#include <linux/signal.h> 24#include <linux/platform_device.h> 25#include <linux/clk.h> 26#include <mach/hardware.h> 27#include <mach/ohci.h> 28#include <mach/pxa3xx-u2d.h> 29 30/* 31 * UHC: USB Host Controller (OHCI-like) register definitions 32 */ 33#define UHCREV (0x0000) /* UHC HCI Spec Revision */ 34#define UHCHCON (0x0004) /* UHC Host Control Register */ 35#define UHCCOMS (0x0008) /* UHC Command Status Register */ 36#define UHCINTS (0x000C) /* UHC Interrupt Status Register */ 37#define UHCINTE (0x0010) /* UHC Interrupt Enable */ 38#define UHCINTD (0x0014) /* UHC Interrupt Disable */ 39#define UHCHCCA (0x0018) /* UHC Host Controller Comm. Area */ 40#define UHCPCED (0x001C) /* UHC Period Current Endpt Descr */ 41#define UHCCHED (0x0020) /* UHC Control Head Endpt Descr */ 42#define UHCCCED (0x0024) /* UHC Control Current Endpt Descr */ 43#define UHCBHED (0x0028) /* UHC Bulk Head Endpt Descr */ 44#define UHCBCED (0x002C) /* UHC Bulk Current Endpt Descr */ 45#define UHCDHEAD (0x0030) /* UHC Done Head */ 46#define UHCFMI (0x0034) /* UHC Frame Interval */ 47#define UHCFMR (0x0038) /* UHC Frame Remaining */ 48#define UHCFMN (0x003C) /* UHC Frame Number */ 49#define UHCPERS (0x0040) /* UHC Periodic Start */ 50#define UHCLS (0x0044) /* UHC Low Speed Threshold */ 51 52#define UHCRHDA (0x0048) /* UHC Root Hub Descriptor A */ 53#define UHCRHDA_NOCP (1 << 12) /* No over current protection */ 54#define UHCRHDA_OCPM (1 << 11) /* Over Current Protection Mode */ 55#define UHCRHDA_POTPGT(x) \ 56 (((x) & 0xff) << 24) /* Power On To Power Good Time */ 57 58#define UHCRHDB (0x004C) /* UHC Root Hub Descriptor B */ 59#define UHCRHS (0x0050) /* UHC Root Hub Status */ 60#define UHCRHPS1 (0x0054) /* UHC Root Hub Port 1 Status */ 61#define UHCRHPS2 (0x0058) /* UHC Root Hub Port 2 Status */ 62#define UHCRHPS3 (0x005C) /* UHC Root Hub Port 3 Status */ 63 64#define UHCSTAT (0x0060) /* UHC Status Register */ 65#define UHCSTAT_UPS3 (1 << 16) /* USB Power Sense Port3 */ 66#define UHCSTAT_SBMAI (1 << 15) /* System Bus Master Abort Interrupt*/ 67#define UHCSTAT_SBTAI (1 << 14) /* System Bus Target Abort Interrupt*/ 68#define UHCSTAT_UPRI (1 << 13) /* USB Port Resume Interrupt */ 69#define UHCSTAT_UPS2 (1 << 12) /* USB Power Sense Port 2 */ 70#define UHCSTAT_UPS1 (1 << 11) /* USB Power Sense Port 1 */ 71#define UHCSTAT_HTA (1 << 10) /* HCI Target Abort */ 72#define UHCSTAT_HBA (1 << 8) /* HCI Buffer Active */ 73#define UHCSTAT_RWUE (1 << 7) /* HCI Remote Wake Up Event */ 74 75#define UHCHR (0x0064) /* UHC Reset Register */ 76#define UHCHR_SSEP3 (1 << 11) /* Sleep Standby Enable for Port3 */ 77#define UHCHR_SSEP2 (1 << 10) /* Sleep Standby Enable for Port2 */ 78#define UHCHR_SSEP1 (1 << 9) /* Sleep Standby Enable for Port1 */ 79#define UHCHR_PCPL (1 << 7) /* Power control polarity low */ 80#define UHCHR_PSPL (1 << 6) /* Power sense polarity low */ 81#define UHCHR_SSE (1 << 5) /* Sleep Standby Enable */ 82#define UHCHR_UIT (1 << 4) /* USB Interrupt Test */ 83#define UHCHR_SSDC (1 << 3) /* Simulation Scale Down Clock */ 84#define UHCHR_CGR (1 << 2) /* Clock Generation Reset */ 85#define UHCHR_FHR (1 << 1) /* Force Host Controller Reset */ 86#define UHCHR_FSBIR (1 << 0) /* Force System Bus Iface Reset */ 87 88#define UHCHIE (0x0068) /* UHC Interrupt Enable Register*/ 89#define UHCHIE_UPS3IE (1 << 14) /* Power Sense Port3 IntEn */ 90#define UHCHIE_UPRIE (1 << 13) /* Port Resume IntEn */ 91#define UHCHIE_UPS2IE (1 << 12) /* Power Sense Port2 IntEn */ 92#define UHCHIE_UPS1IE (1 << 11) /* Power Sense Port1 IntEn */ 93#define UHCHIE_TAIE (1 << 10) /* HCI Interface Transfer Abort 94 Interrupt Enable*/ 95#define UHCHIE_HBAIE (1 << 8) /* HCI Buffer Active IntEn */ 96#define UHCHIE_RWIE (1 << 7) /* Remote Wake-up IntEn */ 97 98#define UHCHIT (0x006C) /* UHC Interrupt Test register */ 99 100#define PXA_UHC_MAX_PORTNUM 3 101 102struct pxa27x_ohci { 103 /* must be 1st member here for hcd_to_ohci() to work */ 104 struct ohci_hcd ohci; 105 106 struct device *dev; 107 struct clk *clk; 108 void __iomem *mmio_base; 109}; 110 111#define to_pxa27x_ohci(hcd) (struct pxa27x_ohci *)hcd_to_ohci(hcd) 112 113/* 114 PMM_NPS_MODE -- PMM Non-power switching mode 115 Ports are powered continuously. 116 117 PMM_GLOBAL_MODE -- PMM global switching mode 118 All ports are powered at the same time. 119 120 PMM_PERPORT_MODE -- PMM per port switching mode 121 Ports are powered individually. 122 */ 123static int pxa27x_ohci_select_pmm(struct pxa27x_ohci *ohci, int mode) 124{ 125 uint32_t uhcrhda = __raw_readl(ohci->mmio_base + UHCRHDA); 126 uint32_t uhcrhdb = __raw_readl(ohci->mmio_base + UHCRHDB); 127 128 switch (mode) { 129 case PMM_NPS_MODE: 130 uhcrhda |= RH_A_NPS; 131 break; 132 case PMM_GLOBAL_MODE: 133 uhcrhda &= ~(RH_A_NPS & RH_A_PSM); 134 break; 135 case PMM_PERPORT_MODE: 136 uhcrhda &= ~(RH_A_NPS); 137 uhcrhda |= RH_A_PSM; 138 139 /* Set port power control mask bits, only 3 ports. */ 140 uhcrhdb |= (0x7<<17); 141 break; 142 default: 143 printk( KERN_ERR 144 "Invalid mode %d, set to non-power switch mode.\n", 145 mode ); 146 147 uhcrhda |= RH_A_NPS; 148 } 149 150 __raw_writel(uhcrhda, ohci->mmio_base + UHCRHDA); 151 __raw_writel(uhcrhdb, ohci->mmio_base + UHCRHDB); 152 return 0; 153} 154 155extern int usb_disabled(void); 156 157/*-------------------------------------------------------------------------*/ 158 159static inline void pxa27x_setup_hc(struct pxa27x_ohci *ohci, 160 struct pxaohci_platform_data *inf) 161{ 162 uint32_t uhchr = __raw_readl(ohci->mmio_base + UHCHR); 163 uint32_t uhcrhda = __raw_readl(ohci->mmio_base + UHCRHDA); 164 165 if (inf->flags & ENABLE_PORT1) 166 uhchr &= ~UHCHR_SSEP1; 167 168 if (inf->flags & ENABLE_PORT2) 169 uhchr &= ~UHCHR_SSEP2; 170 171 if (inf->flags & ENABLE_PORT3) 172 uhchr &= ~UHCHR_SSEP3; 173 174 if (inf->flags & POWER_CONTROL_LOW) 175 uhchr |= UHCHR_PCPL; 176 177 if (inf->flags & POWER_SENSE_LOW) 178 uhchr |= UHCHR_PSPL; 179 180 if (inf->flags & NO_OC_PROTECTION) 181 uhcrhda |= UHCRHDA_NOCP; 182 else 183 uhcrhda &= ~UHCRHDA_NOCP; 184 185 if (inf->flags & OC_MODE_PERPORT) 186 uhcrhda |= UHCRHDA_OCPM; 187 else 188 uhcrhda &= ~UHCRHDA_OCPM; 189 190 if (inf->power_on_delay) { 191 uhcrhda &= ~UHCRHDA_POTPGT(0xff); 192 uhcrhda |= UHCRHDA_POTPGT(inf->power_on_delay / 2); 193 } 194 195 __raw_writel(uhchr, ohci->mmio_base + UHCHR); 196 __raw_writel(uhcrhda, ohci->mmio_base + UHCRHDA); 197} 198 199static inline void pxa27x_reset_hc(struct pxa27x_ohci *ohci) 200{ 201 uint32_t uhchr = __raw_readl(ohci->mmio_base + UHCHR); 202 203 __raw_writel(uhchr | UHCHR_FHR, ohci->mmio_base + UHCHR); 204 udelay(11); 205 __raw_writel(uhchr & ~UHCHR_FHR, ohci->mmio_base + UHCHR); 206} 207 208#ifdef CONFIG_PXA27x 209extern void pxa27x_clear_otgph(void); 210#else 211#define pxa27x_clear_otgph() do {} while (0) 212#endif 213 214static int pxa27x_start_hc(struct pxa27x_ohci *ohci, struct device *dev) 215{ 216 int retval = 0; 217 struct pxaohci_platform_data *inf; 218 uint32_t uhchr; 219 220 inf = dev->platform_data; 221 222 clk_prepare_enable(ohci->clk); 223 224 pxa27x_reset_hc(ohci); 225 226 uhchr = __raw_readl(ohci->mmio_base + UHCHR) | UHCHR_FSBIR; 227 __raw_writel(uhchr, ohci->mmio_base + UHCHR); 228 229 while (__raw_readl(ohci->mmio_base + UHCHR) & UHCHR_FSBIR) 230 cpu_relax(); 231 232 pxa27x_setup_hc(ohci, inf); 233 234 if (inf->init) 235 retval = inf->init(dev); 236 237 if (retval < 0) 238 return retval; 239 240 if (cpu_is_pxa3xx()) 241 pxa3xx_u2d_start_hc(&ohci_to_hcd(&ohci->ohci)->self); 242 243 uhchr = __raw_readl(ohci->mmio_base + UHCHR) & ~UHCHR_SSE; 244 __raw_writel(uhchr, ohci->mmio_base + UHCHR); 245 __raw_writel(UHCHIE_UPRIE | UHCHIE_RWIE, ohci->mmio_base + UHCHIE); 246 247 /* Clear any OTG Pin Hold */ 248 pxa27x_clear_otgph(); 249 return 0; 250} 251 252static void pxa27x_stop_hc(struct pxa27x_ohci *ohci, struct device *dev) 253{ 254 struct pxaohci_platform_data *inf; 255 uint32_t uhccoms; 256 257 inf = dev->platform_data; 258 259 if (cpu_is_pxa3xx()) 260 pxa3xx_u2d_stop_hc(&ohci_to_hcd(&ohci->ohci)->self); 261 262 if (inf->exit) 263 inf->exit(dev); 264 265 pxa27x_reset_hc(ohci); 266 267 /* Host Controller Reset */ 268 uhccoms = __raw_readl(ohci->mmio_base + UHCCOMS) | 0x01; 269 __raw_writel(uhccoms, ohci->mmio_base + UHCCOMS); 270 udelay(10); 271 272 clk_disable_unprepare(ohci->clk); 273} 274 275 276/*-------------------------------------------------------------------------*/ 277 278/* configure so an HC device and id are always provided */ 279/* always called with process context; sleeping is OK */ 280 281 282/** 283 * usb_hcd_pxa27x_probe - initialize pxa27x-based HCDs 284 * Context: !in_interrupt() 285 * 286 * Allocates basic resources for this USB host controller, and 287 * then invokes the start() method for the HCD associated with it 288 * through the hotplug entry's driver_data. 289 * 290 */ 291int usb_hcd_pxa27x_probe (const struct hc_driver *driver, struct platform_device *pdev) 292{ 293 int retval, irq; 294 struct usb_hcd *hcd; 295 struct pxaohci_platform_data *inf; 296 struct pxa27x_ohci *ohci; 297 struct resource *r; 298 struct clk *usb_clk; 299 300 inf = pdev->dev.platform_data; 301 302 if (!inf) 303 return -ENODEV; 304 305 irq = platform_get_irq(pdev, 0); 306 if (irq < 0) { 307 pr_err("no resource of IORESOURCE_IRQ"); 308 return -ENXIO; 309 } 310 311 usb_clk = clk_get(&pdev->dev, NULL); 312 if (IS_ERR(usb_clk)) 313 return PTR_ERR(usb_clk); 314 315 hcd = usb_create_hcd (driver, &pdev->dev, "pxa27x"); 316 if (!hcd) { 317 retval = -ENOMEM; 318 goto err0; 319 } 320 321 r = platform_get_resource(pdev, IORESOURCE_MEM, 0); 322 if (!r) { 323 pr_err("no resource of IORESOURCE_MEM"); 324 retval = -ENXIO; 325 goto err1; 326 } 327 328 hcd->rsrc_start = r->start; 329 hcd->rsrc_len = resource_size(r); 330 331 if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) { 332 pr_debug("request_mem_region failed"); 333 retval = -EBUSY; 334 goto err1; 335 } 336 337 hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len); 338 if (!hcd->regs) { 339 pr_debug("ioremap failed"); 340 retval = -ENOMEM; 341 goto err2; 342 } 343 344 /* initialize "struct pxa27x_ohci" */ 345 ohci = (struct pxa27x_ohci *)hcd_to_ohci(hcd); 346 ohci->dev = &pdev->dev; 347 ohci->clk = usb_clk; 348 ohci->mmio_base = (void __iomem *)hcd->regs; 349 350 if ((retval = pxa27x_start_hc(ohci, &pdev->dev)) < 0) { 351 pr_debug("pxa27x_start_hc failed"); 352 goto err3; 353 } 354 355 /* Select Power Management Mode */ 356 pxa27x_ohci_select_pmm(ohci, inf->port_mode); 357 358 if (inf->power_budget) 359 hcd->power_budget = inf->power_budget; 360 361 ohci_hcd_init(hcd_to_ohci(hcd)); 362 363 retval = usb_add_hcd(hcd, irq, 0); 364 if (retval == 0) 365 return retval; 366 367 pxa27x_stop_hc(ohci, &pdev->dev); 368 err3: 369 iounmap(hcd->regs); 370 err2: 371 release_mem_region(hcd->rsrc_start, hcd->rsrc_len); 372 err1: 373 usb_put_hcd(hcd); 374 err0: 375 clk_put(usb_clk); 376 return retval; 377} 378 379 380/* may be called without controller electrically present */ 381/* may be called with controller, bus, and devices active */ 382 383/** 384 * usb_hcd_pxa27x_remove - shutdown processing for pxa27x-based HCDs 385 * @dev: USB Host Controller being removed 386 * Context: !in_interrupt() 387 * 388 * Reverses the effect of usb_hcd_pxa27x_probe(), first invoking 389 * the HCD's stop() method. It is always called from a thread 390 * context, normally "rmmod", "apmd", or something similar. 391 * 392 */ 393void usb_hcd_pxa27x_remove (struct usb_hcd *hcd, struct platform_device *pdev) 394{ 395 struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd); 396 397 usb_remove_hcd(hcd); 398 pxa27x_stop_hc(ohci, &pdev->dev); 399 iounmap(hcd->regs); 400 release_mem_region(hcd->rsrc_start, hcd->rsrc_len); 401 usb_put_hcd(hcd); 402 clk_put(ohci->clk); 403} 404 405/*-------------------------------------------------------------------------*/ 406 407static int __devinit 408ohci_pxa27x_start (struct usb_hcd *hcd) 409{ 410 struct ohci_hcd *ohci = hcd_to_ohci (hcd); 411 int ret; 412 413 ohci_dbg (ohci, "ohci_pxa27x_start, ohci:%p", ohci); 414 415 /* The value of NDP in roothub_a is incorrect on this hardware */ 416 ohci->num_ports = 3; 417 418 if ((ret = ohci_init(ohci)) < 0) 419 return ret; 420 421 if ((ret = ohci_run (ohci)) < 0) { 422 err ("can't start %s", hcd->self.bus_name); 423 ohci_stop (hcd); 424 return ret; 425 } 426 427 return 0; 428} 429 430/*-------------------------------------------------------------------------*/ 431 432static const struct hc_driver ohci_pxa27x_hc_driver = { 433 .description = hcd_name, 434 .product_desc = "PXA27x OHCI", 435 .hcd_priv_size = sizeof(struct pxa27x_ohci), 436 437 /* 438 * generic hardware linkage 439 */ 440 .irq = ohci_irq, 441 .flags = HCD_USB11 | HCD_MEMORY, 442 443 /* 444 * basic lifecycle operations 445 */ 446 .start = ohci_pxa27x_start, 447 .stop = ohci_stop, 448 .shutdown = ohci_shutdown, 449 450 /* 451 * managing i/o requests and associated device resources 452 */ 453 .urb_enqueue = ohci_urb_enqueue, 454 .urb_dequeue = ohci_urb_dequeue, 455 .endpoint_disable = ohci_endpoint_disable, 456 457 /* 458 * scheduling support 459 */ 460 .get_frame_number = ohci_get_frame, 461 462 /* 463 * root hub support 464 */ 465 .hub_status_data = ohci_hub_status_data, 466 .hub_control = ohci_hub_control, 467#ifdef CONFIG_PM 468 .bus_suspend = ohci_bus_suspend, 469 .bus_resume = ohci_bus_resume, 470#endif 471 .start_port_reset = ohci_start_port_reset, 472}; 473 474/*-------------------------------------------------------------------------*/ 475 476static int ohci_hcd_pxa27x_drv_probe(struct platform_device *pdev) 477{ 478 pr_debug ("In ohci_hcd_pxa27x_drv_probe"); 479 480 if (usb_disabled()) 481 return -ENODEV; 482 483 return usb_hcd_pxa27x_probe(&ohci_pxa27x_hc_driver, pdev); 484} 485 486static int ohci_hcd_pxa27x_drv_remove(struct platform_device *pdev) 487{ 488 struct usb_hcd *hcd = platform_get_drvdata(pdev); 489 490 usb_hcd_pxa27x_remove(hcd, pdev); 491 platform_set_drvdata(pdev, NULL); 492 return 0; 493} 494 495#ifdef CONFIG_PM 496static int ohci_hcd_pxa27x_drv_suspend(struct device *dev) 497{ 498 struct usb_hcd *hcd = dev_get_drvdata(dev); 499 struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd); 500 501 if (time_before(jiffies, ohci->ohci.next_statechange)) 502 msleep(5); 503 ohci->ohci.next_statechange = jiffies; 504 505 pxa27x_stop_hc(ohci, dev); 506 return 0; 507} 508 509static int ohci_hcd_pxa27x_drv_resume(struct device *dev) 510{ 511 struct usb_hcd *hcd = dev_get_drvdata(dev); 512 struct pxa27x_ohci *ohci = to_pxa27x_ohci(hcd); 513 struct pxaohci_platform_data *inf = dev->platform_data; 514 int status; 515 516 if (time_before(jiffies, ohci->ohci.next_statechange)) 517 msleep(5); 518 ohci->ohci.next_statechange = jiffies; 519 520 if ((status = pxa27x_start_hc(ohci, dev)) < 0) 521 return status; 522 523 /* Select Power Management Mode */ 524 pxa27x_ohci_select_pmm(ohci, inf->port_mode); 525 526 ohci_finish_controller_resume(hcd); 527 return 0; 528} 529 530static const struct dev_pm_ops ohci_hcd_pxa27x_pm_ops = { 531 .suspend = ohci_hcd_pxa27x_drv_suspend, 532 .resume = ohci_hcd_pxa27x_drv_resume, 533}; 534#endif 535 536/* work with hotplug and coldplug */ 537MODULE_ALIAS("platform:pxa27x-ohci"); 538 539static struct platform_driver ohci_hcd_pxa27x_driver = { 540 .probe = ohci_hcd_pxa27x_drv_probe, 541 .remove = ohci_hcd_pxa27x_drv_remove, 542 .shutdown = usb_hcd_platform_shutdown, 543 .driver = { 544 .name = "pxa27x-ohci", 545 .owner = THIS_MODULE, 546#ifdef CONFIG_PM 547 .pm = &ohci_hcd_pxa27x_pm_ops, 548#endif 549 }, 550}; 551 552