| 1d266430546acf01438ae42d0a7370db4817e2ad |
|
05-Feb-2012 |
Pradeep A Dalvi <netdev@pradeepdalvi.com> |
netdev: ethernet dev_alloc_skb to netdev_alloc_skb
Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet
- Removed extra skb->dev = dev after netdev_alloc_skb
Signed-off-by: Pradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 2839038bb1a72ed7ef3c39521e0ca981c9cb1534 |
|
24-Nov-2011 |
Nicolas Ferre <nicolas.ferre@atmel.com> |
net/at91_ether: use gpio_is_valid for phy IRQ line
Use the generic gpiolib gpio_is_valid() function to test
if the phy IRQ line GPIO is actually provided.
For non-connected or non-existing phy IRQ lines, -EINVAL
value is used for phy_irq_pin field of struct at91_eth_data.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: David S. Miller <davem@davemloft.net>
|
| 84e0cdb0a262483a3618091c43dae33d36226430 |
|
08-Mar-2011 |
Jamie Iles <jamie@jamieiles.com> |
macb: unify at91 and avr32 platform data
Both at91 and avr32 defines its own platform data structure for
the macb driver and both share common structures though at91
includes a currently unused phy_irq_pin. Create a common
macb_platform_data for macb that both at91 and avr32 can use. In
future we can use this to support other architectures that use the
same IP block with the macb driver.
v2: rename eth_platform_data to macb_platform_data and allow at91_ether
to share the platform data with macb.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
| afc4b13df143122f99a0eb10bfefb216c2806de0 |
|
16-Aug-2011 |
Jiri Pirko <jpirko@redhat.com> |
net: remove use of ndo_set_multicast_list in drivers
replace it by ndo_set_rx_mode
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| 9f2f381f813858755f5b6ef7af316feda0726ef3 |
|
18-Jun-2011 |
Jeff Kirsher <jeffrey.t.kirsher@intel.com> |
macb: Move the Atmel driver
Move the Atmel driver into drivers/net/ethernet/cadence/ and
make the necessary Kconfig and Makefile changes.
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|