7d1d865181185bdf1316d236b1b4bd02c9020729 |
|
20-Mar-2012 |
Dan Williams <dan.j.williams@intel.com> |
[SCSI] libsas: fix false positive 'device attached' conditions Normalize phy->attached_sas_addr to return a zero-address in the case when device-type == NO_DEVICE or the linkrate is invalid to handle expanders that put non-zero sas addresses in the discovery response: sas: ex 5001b4da000f903f phy02:U:0 attached: 0100000000000000 (no device) sas: ex 5001b4da000f903f phy01:U:0 attached: 0100000000000000 (no device) sas: ex 5001b4da000f903f phy03:U:0 attached: 0100000000000000 (no device) sas: ex 5001b4da000f903f phy00:U:0 attached: 0100000000000000 (no device) Reported-by: Andrzej Jakowski <andrzej.jakowski@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Cc: stable@vger.kernel.org Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
b2024459252a9d2d312ee562f86f332a1498f412 |
|
22-Mar-2012 |
Dan Williams <dan.j.williams@intel.com> |
[SCSI] libsas, libata: fix start of life for a sas ata_port This changes the ordering of initialization and probing events from: 1/ allocate rphy in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN 2/ allocate ata_port and schedule port probe in DISCE_PROBE ...to: 1/ allocate ata_port in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN 2/ allocate rphy in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN 3/ schedule port probe in DISCE_PROBE This ordering prevents PHYE_SIGNAL_LOSS_EVENTS from sneaking in to destrory ata devices before they have been fully initialized: BUG: unable to handle kernel paging request at 0000000000003b10 IP: [<ffffffffa0053d7e>] sas_ata_end_eh+0x12/0x5e [libsas] ... [<ffffffffa004d1af>] sas_unregister_common_dev+0x78/0xc9 [libsas] [<ffffffffa004d4d4>] sas_unregister_dev+0x4f/0xad [libsas] [<ffffffffa004d5b1>] sas_unregister_domain_devices+0x7f/0xbf [libsas] [<ffffffffa004c487>] sas_deform_port+0x61/0x1b8 [libsas] [<ffffffffa004bed0>] sas_phye_loss_of_signal+0x29/0x2b [libsas] ...and kills the awkward "sata domain_device briefly existing in the domain without an ata_port" state. Reported-by: Michal Kosciowski <michal.kosciowski@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Acked-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
0f3fce5cc77e1f35758ef0e46a989e76e5046a7b |
|
20-Mar-2012 |
Dan Williams <dan.j.williams@intel.com> |
[SCSI] libsas: fix ata_eh clobbering ex_phys via smp_ata_check_ready The check_ready implementation in the expander-attached ata device case polls on sas_ex_phy_discover(). The effect is that the ex_phy fields (critically ->attached_sas_addr) can change. When ata_eh ends and libsas comes along to revalidate the domain sas_unregister_devs_sas_addr() can fail to lookup devices to remove, or fail to re-add an ata device that ata_eh marked as disabled. So change the code to skip the sas_address and change count updates when ata_eh is active. Cc: Jack Wang <jack_wang@usish.com> Tested-by: Maciej Patelczyk <maciej.patelczyk@intel.com> Tested-by: Bartek Nowakowski <bartek.nowakowski@intel.com> Tested-by: Jacek Danecki <jacek.danecki@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
9487669fc225092cf315e1291ece28e23e6754f3 |
|
20-Mar-2012 |
Dan Williams <dan.j.williams@intel.com> |
[SCSI] libsas: unify domain_device sas_rphy lifetimes Since the domain_device can out live the scsi_target we need the rphy to follow suit otherwise we run into issues like: BUG: unable to handle kernel NULL pointer dereference at 0000000000000050 IP: [<ffffffffa011561b>] sas_ata_printk+0x43/0x6f [libsas] PGD 0 Oops: 0000 [#1] SMP CPU 1 Modules linked in: ses enclosure isci libsas scsi_transport_sas fuse sunrpc cpufreq_ondemand acpi_cpufreq freq_table mperf microcode pcspkr igb joydev iTCO_wdt ioatdma iTCO_vendor_support i2c_i801 i2c_core dca wmi hed ipv6 pata_acpi ata_generic [last unloaded: scsi_wait_scan] Pid: 129, comm: kworker/u:3 Not tainted 3.3.0-rc5-isci+ #1 Intel Corporation SandyBridge Platform/To be filled by O.E.M. RIP: 0010:[<ffffffffa011561b>] [<ffffffffa011561b>] sas_ata_printk+0x43/0x6f [libsas] RSP: 0018:ffff88042232dd70 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffff8804283165b8 RCX: ffff88042232dda0 RDX: ffff88042232dd78 RSI: ffff8804283165b8 RDI: ffffffffa01188d7 RBP: ffff88042232ddd0 R08: ffff880388454000 R09: ffff8803edfde1f8 R10: ffff8803edfde1f8 R11: ffff8803edfde1f8 R12: ffff880428316750 R13: ffff880388454000 R14: ffff8803f88b31d0 R15: ffff8803f8b21d50 FS: 0000000000000000(0000) GS:ffff88042ee20000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 0000000000000050 CR3: 0000000001a05000 CR4: 00000000000406e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process kworker/u:3 (pid: 129, threadinfo ffff88042232c000, task ffff88042230c920) Stack: 0000000000000000 ffff880400000018 ffff88042232dde0 ffff88042232dda0 ffffffffa01188c4 ffff88042ee93af0 ffff88042232ddb0 ffffffff8100e047 ffff88042232de10 ffff880420e5a2c8 ffff8803f8b21d50 ffff8803edfde1f8 Call Trace: [<ffffffff8100e047>] ? load_TLS+0xb/0xf [<ffffffffa01156ad>] async_sas_ata_eh+0x66/0x95 [libsas] [<ffffffff810655e1>] async_run_entry_fn+0x9e/0x131 Reported-by: Tom Jackson <thomas.p.jackson@intel.com> Tested-by: Tom Jackson <thomas.p.jackson@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
1699490db339e2c6b3037ea8e7dcd6b2755b688e |
|
18-Feb-2012 |
Thomas Jackson <thomas.p.jackson@intel.com> |
[SCSI] libsas: fix sas_find_bcast_phy() in the presence of 'vacant' phys If an expander reports 'PHY VACANT' for a phy index prior to the one that generated a BCN libsas fails rediscovery. Since a vacant phy is defined as a valid phy index that will never have an attached device just continue the search. Cc: <stable@vger.kernel.org> Signed-off-by: Thomas Jackson <thomas.p.jackson@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
77c309f3cdf9e217032dfe330f5881d352bb0436 |
|
09-Feb-2012 |
Dan Williams <dan.j.williams@intel.com> |
[SCSI] libsas: fixup target_port_protocols for expanders that don't report sata If discovery returns 0 for target_port_protocols but shows an attached sata device, just report SAS_PROTOCOL_SATA in the identify data so userspace can reliably search for sata devices in the domain. Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
92625f9bff3853951cc75f5bc084ee67c1317d2f |
|
19-Jan-2012 |
Dan Williams <dan.j.williams@intel.com> |
[SCSI] libsas: restore scan order ata devices are always scanned after ssp. Prior to the ata error handling reworks libsas would tend to scan devices in ascending expander phy order. Restore this ordering by deferring ssp discovery to a DISCE_PROBE event, and keep the probe order consistent with the discovery order, not the placement of sata devices. Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
c666aae6919114d6cff789d79f80cfa85f3a7339 |
|
20-Jan-2012 |
Dan Williams <dan.j.williams@intel.com> |
[SCSI] libsas: delete device on sas address changed If the phy is attached to a new sas address unregister the first address before processing the new attachment. Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
354cf82980e2449e71fdaa3c6f170357ebd65467 |
|
13-Jan-2012 |
Dan Williams <dan.j.williams@intel.com> |
[SCSI] libsas: let libata recover links that fail to transmit initial sig-fis libsas fails to discover all sata devices in the domain. If a device fails negotiation and does not transmit a signature fis the link needs recovery. libata already understands how to manage slow to come up links, so treat these conditions as ata device attach events for the purposes of creating an ata_port. This allows libata to manage retrying link bring up. Rediscovery is modified to be careful about checking changes in dev_type. It looks like libsas leaks old devices if the sas address changes, but that's a fix for another patch. Acked-by: Jack Wang <jack_wang@usish.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
d214d81e883b6fc6f11cc772ff88585565d45cce |
|
16-Jan-2012 |
Dan Williams <dan.j.williams@intel.com> |
[SCSI] libsas: improve debug statements It's difficult to determine which domain_device is triggering error recovery, so convert messages like: sas: ex 5001b4da000e703f phy08:T attached: 5001b4da000e7028 sas: ex 5001b4da000e703f phy09:T attached: 5001b4da000e7029 ... ata7: sas eh calling libata port error handler ata8: sas eh calling libata port error handler ...into: sas: ex 5001517e85cfefff phy05:T:9 attached: 5001517e85cfefe5 (stp) sas: ex 5001517e3b0af0bf phy11:T:8 attached: 5001517e3b0af0ab (stp) ... sas: ata7: end_device-21:1: dev error handler sas: ata8: end_device-20:0:5: dev error handler which shows attached link rate, device type, and associates a domain_device with its ata_port id to correlate messages emitted from libata-eh. As Doug notes, we can also take the opportunity to clarify expander phy routing capabilities. [dgilbert@interlog.com: clarify table2table with 'U'] Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
f41a0c441c3fe43e79ebeb75584dbb5bfa83e5cd |
|
22-Dec-2011 |
Dan Williams <dan.j.williams@intel.com> |
[SCSI] libsas: fix sas_find_local_phy(), take phy references In the direct-attached case this routine returns the phy on which this device was first discovered. Which is broken if we want to support wide-targets, as this phy reference can become stale even though the port is still active. In the expander-attached case this routine tries to lookup the phy by scanning the attached sas addresses of the parent expander, and BUG_ONs if it can't find it. However since eh and the libsas workqueue run independently we can still be attempting device recovery via eh after libsas has recorded the device as detached. This is even easier to hit now that eh is blocked while device domain rediscovery takes place, and that libata is fed more timed out commands increasing the chances that it will try to recover the ata device. Arrange for dev->phy to always point to a last known good phy, it may be stale after the port is torn down, but it will catch up for wide port reconfigurations, and never be NULL. Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
3a9c5560f677690f65038f399f4f598c79b83186 |
|
22-Dec-2011 |
Dan Williams <dan.j.williams@intel.com> |
[SCSI] libsas: check for 'gone' expanders in smp_execute_task() No sense in issuing or retrying commands to an expander that has been removed. Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
0508c2f3b701f3cd8ed52b2a4abbb2a670f69ce2 |
|
21-Dec-2011 |
Dan Williams <dan.j.williams@intel.com> |
[SCSI] libsas: don't mark expanders as gone when a child device is removed Commit 56dd2c06 "[SCSI] libsas: Don't issue commands to devices that have been hot-removed" marked the parent device of an end-device as gone when all the phys to the end device have been deleted. The expander device is still present until its parent is removed. This is a benign change until the smp_execute_task() path is taught to check ->gone. Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
36a399473902a57218dc493c5a814708a56b73ab |
|
18-Nov-2011 |
Dan Williams <dan.j.williams@intel.com> |
[SCSI] libsas: poll for ata device readiness after reset Use ata_wait_after_reset() to poll for link recovery after a reset. This combined with sas_ha->eh_mutex prevents expander rediscovery from probing phys in an intermediate state. Local discovery does not have a mechanism to filter link status changes during this timeout, so it remains the responsibility of lldds to prevent premature port teardown. Although once all lldd's support ->lldd_ata_check_ready() that could be used as a gate to local port teardown. The signature fis is re-transmitted when the link comes back so we should be revalidating the ata device class, but that is left to a future patch. Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
89d3cf6ac3cdc4f15a82709f8c78ed169a98be5b |
|
16-Nov-2011 |
Jeff Skirvin <jeffrey.d.skirvin@intel.com> |
[SCSI] libsas: add mutex for SMP task execution SAS does not tag SMP requests, and at least one lldd (isci) does not permit more than one in-flight request at a time. [jejb: fix sas_init_dev tab issues while we're at it] Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
81c757bc696284f39f07766f0c2ca67af64ce9bd |
|
03-Dec-2011 |
Dan Williams <dan.j.williams@intel.com> |
[SCSI] libsas: execute transport link resets with libata-eh via host workqueue Link resets leave ata affiliations intact, so arrange for libsas to make an effort to avoid dropping the device due to a slow-to-recover link. Towards this end carry out reset in the host workqueue so that it can check for ata devices and kick the reset request to libata. Hard resets, in contrast, bypass libata since they are meant for associating an ata device with another initiator in the domain (tears down affiliations). Need to add a new transport_sas_phy_reset() since the current sas_phy_reset() is a utility function to libsas lldds. They are not prepared for it to loop back into eh. Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
b52df4174dff7e587f6fbfb21e3c2cb57109e5cf |
|
01-Dec-2011 |
Dan Williams <dan.j.williams@intel.com> |
[SCSI] libsas: use libata-eh-reset for sata rediscovery fis transmit failures Since sata devices can take several seconds to recover the link on reset the 0.5 seconds that libsas currently waits may not be enough. Instead if we are rediscovering a phy that was previously attached to a sata device let libata handle any resets to encourage the device to transmit the initial fis. Once sas_ata_hard_reset() and lldds learn how to honor 'deadline' libsas should stop encountering phys in an intermediate state, until then this will loop until the fis is transmitted or ->attached_sas_addr gets cleared, but in the more likely initial discovery case we keep existing behavior. Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
87c8331fcf72e501c3a3c0cdc5c9391ec72f7cf2 |
|
18-Nov-2011 |
Dan Williams <dan.j.williams@intel.com> |
[SCSI] libsas: prevent domain rediscovery competing with ata error handling libata error handling provides for a timeout for link recovery. libsas must not rescan for previously known devices in this interval otherwise it may remove a device that is simply waiting for its link to recover. Let libata-eh make the determination of when the link is stable and prevent libsas (host workqueue) from taking action while this determination is pending. Using a mutex (ha->disco_mutex) to flush and disable revalidation while eh is running requires any discovery action that may block on eh be moved to its own context outside the lock. Probing ATA devices explicitly waits on ata-eh and the cache-flush-io issued during device removal may also pend awaiting eh completion. Essentially any rphy add/remove activity needs to run outside the lock. This adds two new cleanup states for sas_unregister_domain_devices() 'allocated-but-not-probed', and 'flagged-for-destruction'. In the 'allocated-but-not-probed' state dev->rphy points to a rphy that is known to have not been through a sas_rphy_add() event. At domain teardown check if this device is still pending probe and cleanup accordingly. Similarly if a device has already been queued for removal then sas_unregister_domain_devices has nothing to do. Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
e139942d77a6e3ac83bc322e826668054a8601d6 |
|
07-Jan-2012 |
Dan Williams <dan.j.williams@intel.com> |
[SCSI] libsas: convert dev->gone to flags In preparation for adding tracking of another device state "destroy". Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
735f7d2fedf57380214221be7bed7f62d729e262 |
|
18-Nov-2011 |
Dan Williams <dan.j.williams@intel.com> |
[SCSI] libsas: fix domain_device leak Arrange for the deallocation of a struct domain_device object when it no longer has: 1/ any children 2/ references by any scsi_targets 3/ references by a lldd The comment about domain_device lifetime in Documentation/scsi/libsas.txt is stale as it appears mainline never had a version of a struct domain_device that was registered as a kobject. We now manage domain_device reference counts on behalf of external agents. Reviewed-by: Jack Wang <jack_wang@usish.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
1a34c0640137eed8dabdac3a68a7a84116ac9e0d |
|
22-Sep-2011 |
Dan Williams <dan.j.williams@intel.com> |
[SCSI] libsas: fix port->dev_list locking port->dev_list maintains a list of devices attached to a given sas root port. It needs to be mutated under a lock as contexts outside of the single-threaded-libsas-workqueue access the list via sas_find_dev_by_rphy(). Fixup locations where the list was being mutated without a lock. This is a follow-up to commit 5911e963 "[SCSI] libsas: remove expander from dev list on error", where Luben noted [1]: > 2/ We have unlocked list manipulations in sas_ex_discover_end_dev(), > sas_unregister_common_dev(), and sas_ex_discover_end_dev() Yes, I can see that and that is very unfortunate. [1]: http://marc.info/?l=linux-scsi&m=131480962006471&w=2 Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
a73914c35b05d80f8ce78288e10056c91090b666 |
|
22-Sep-2011 |
Mark Salyzyn <mark_salyzyn@us.xyratex.com> |
[SCSI] libsas: fix panic when single phy is disabled on a wide port When a wide port is being utilized to a target, if one disables only one of the phys, we get an OS crash: BUG: unable to handle kernel NULL pointer dereference at 0000000000000238 IP: [<ffffffff814ca9b1>] mutex_lock+0x21/0x50 PGD 4103f5067 PUD 41dba9067 PMD 0 Oops: 0002 [#1] SMP last sysfs file: /sys/bus/pci/slots/5/address CPU 0 Modules linked in: pm8001(U) ses enclosure fuse nfsd exportfs autofs4 ipmi_devintf ipmi_si ipmi_msghandler nfs lockd fscache nfs_acl auth_rpcgss 8021q fcoe libfcoe garp libfc scsi_transport_fc stp scsi_tgt llc sunrpc cpufreq_ondemand acpi_cpufreq freq_table ipv6 sr_mod cdrom dm_mirror dm_region_hash dm_log uinput sg i2c_i801 i2c_core iTCO_wdt iTCO_vendor_support e1000e mlx4_ib ib_mad ib_core mlx4_en mlx4_core ext3 jbd mbcache sd_mod crc_t10dif usb_storage ata_generic pata_acpi ata_piix libsas(U) scsi_transport_sas dm_mod [last unloaded: pm8001] Modules linked in: pm8001(U) ses enclosure fuse nfsd exportfs autofs4 ipmi_devintf ipmi_si ipmi_msghandler nfs lockd fscache nfs_acl auth_rpcgss 8021q fcoe libfcoe garp libfc scsi_transport_fc stp scsi_tgt llc sunrpc cpufreq_ondemand acpi_cpufreq freq_table ipv6 sr_mod cdrom dm_mirror dm_region_hash dm_log uinput sg i2c_i801 i2c_core iTCO_wdt iTCO_vendor_support e1000e mlx4_ib ib_mad ib_core mlx4_en mlx4_core ext3 jbd mbcache sd_mod crc_t10dif usb_storage ata_generic pata_acpi ata_piix libsas(U) scsi_transport_sas dm_mod [last unloaded: pm8001] Pid: 5146, comm: scsi_wq_5 Not tainted 2.6.32-71.29.1.el6.lustre.7.x86_64 #1 Storage Server RIP: 0010:[<ffffffff814ca9b1>] [<ffffffff814ca9b1>] mutex_lock+0x21/0x50 RSP: 0018:ffff8803e4e33d30 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000238 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffff8803e664c800 RDI: 0000000000000238 RBP: ffff8803e4e33d40 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000000 R13: 0000000000000238 R14: ffff88041acb7200 R15: ffff88041c51ada0 FS: 0000000000000000(0000) GS:ffff880028200000(0000) knlGS:0000000000000000 CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b CR2: 0000000000000238 CR3: 0000000410143000 CR4: 00000000000006f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process scsi_wq_5 (pid: 5146, threadinfo ffff8803e4e32000, task ffff8803e4e294a0) Stack: ffff8803e664c800 0000000000000000 ffff8803e4e33d70 ffffffffa001f06e <0> ffff8803e4e33d60 ffff88041c51ada0 ffff88041acb7200 ffff88041bc0aa00 <0> ffff8803e4e33d90 ffffffffa0032b6c 0000000000000014 ffff88041acb7200 Call Trace: [<ffffffffa001f06e>] sas_port_delete_phy+0x2e/0xa0 [scsi_transport_sas] [<ffffffffa0032b6c>] sas_unregister_devs_sas_addr+0xac/0xe0 [libsas] [<ffffffffa0034914>] sas_ex_revalidate_domain+0x204/0x330 [libsas] [<ffffffffa00307f0>] ? sas_revalidate_domain+0x0/0x90 [libsas] [<ffffffffa0030855>] sas_revalidate_domain+0x65/0x90 [libsas] [<ffffffff8108c7d0>] worker_thread+0x170/0x2a0 [<ffffffff81091ea0>] ? autoremove_wake_function+0x0/0x40 [<ffffffff8108c660>] ? worker_thread+0x0/0x2a0 [<ffffffff81091b36>] kthread+0x96/0xa0 [<ffffffff810141ca>] child_rip+0xa/0x20 [<ffffffff81091aa0>] ? kthread+0x0/0xa0 [<ffffffff810141c0>] ? child_rip+0x0/0x20 Code: ff ff 85 c0 75 ed eb d6 66 90 55 48 89 e5 48 83 ec 10 48 89 1c 24 4c 89 64 24 08 0f 1f 44 00 00 48 89 fb e8 92 f4 ff ff 48 89 df <f0> ff 0f 79 05 e8 25 00 00 00 65 48 8b 04 25 08 cc 00 00 48 2d RIP [<ffffffff814ca9b1>] mutex_lock+0x21/0x50 RSP <ffff8803e4e33d30> CR2: 0000000000000238 The following patch is admittedly a band-aid, and does not solve the root cause, but it still is a good candidate for hardening as a pointer check before reference. Signed-off-by: Mark Salyzyn <mark_salyzyn@us.xyratex.com> Tested-by: Jack Wang <jack_wang@usish.com> Cc: stable@kernel.org Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
bb041a0e9c31229071b6e56e1d0d8374af0d2038 |
|
23-Sep-2011 |
Jack Wang <jack_wang@usish.com> |
[SCSI] libsas: set sas_address and device type of rphy Libsas forget to set the sas_address and device type of rphy lead to file under /sys/class/sas_x show wrong value, fix that. Signed-off-by: Jack Wang <jack_wang@usish.com> Tested-by: Crystal Yu <crystal_yu@usish.com> Cc: stable@kernel.org Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
ffaac8f45bfb2dffb78179baa5740de34058eef8 |
|
22-Sep-2011 |
Luben Tuikov <ltuikov@yahoo.com> |
[SCSI] libsas: Allow expander T-T attachments Allow expander table-to-table attachments for expanders that support it. Signed-off-by: Luben Tuikov <ltuikov@yahoo.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
24926dadc41cc566e974022b0e66231b82c6375f |
|
01-Sep-2011 |
Mark Salyzyn <mark_salyzyn@us.xyratex.com> |
[SCSI] libsas: fix failure to revalidate domain for anything but the first expander child. In an enclosure model where there are chaining expanders to a large body of storage, it was discovered that libsas, responding to a broadcast event change, would only revalidate the domain of first child expander in the list. The issue is that the pointer value to the discovered source device was used to break out of the loop, rather than the content of the pointer. This still remains non-compliant as the revalidate domain code is supposed to loop through all child expanders, and not stop at the first one it finds that reports a change count. However, the design of this routine does not allow multiple device discoveries and that would be a more complicated set of patches reserved for another day. We are fixing the glaring bug rather than refactoring the code. Signed-off-by: Mark Salyzyn <msalyzyn@us.xyratex.com> Cc: stable@kernel.org Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
5911e963d3718e306bcac387b83e259aa4228896 |
|
27-Jul-2011 |
Luben Tuikov <ltuikov@yahoo.com> |
[SCSI] libsas: remove expander from dev list on error If expander discovery fails (sas_discover_expander()), remove the expander from the port device list (sas_ex_discover_expander()), before freeing it. Else the list is corrupted and, e.g., when we attempt to send SMP commands to other devices, the kernel oopses. Signed-off-by: Luben Tuikov <ltuikov@yahoo.com> Cc: stable@kernel.org Reviewed-by: Jack Wang <jack_wang@usish.com> Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
25985edcedea6396277003854657b5f3cb31a628 |
|
31-Mar-2011 |
Lucas De Marchi <lucas.demarchi@profusion.mobi> |
Fix common misspellings Fixes generated by 'codespell' and manually reviewed. Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
183ce896d726fb987da589fa8e36fb7214a494cc |
|
19-Feb-2011 |
jack_wang <jack_wang@usish.com> |
[SCSI] libsas: fix loopback topology bug during discovery In some test envirenment, there is loopback topology test. We should handle this during discovery. Signed-off-by: Jack Wang <jack_wang@usish.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
2bc72c91ea7e104b0e40151543d135b933a12e93 |
|
06-Oct-2010 |
Jack Wang <jack_wang@usish.com> |
[SCSI] libsas: fix bug for vacant phy This patch fix bug reported by Chuck. And this new version incorporate comments from Hannes. Please consider to include it into mainline. Signed-off-by: Jack Wang <jack_wang@usish.com> Signed-off-by: Lindar Liu <lindar_liu@usish.com> Tested-by: Chuck Tuffli <Chuck_Tuffli@pmc-sierra.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
56dd2c0691a5a387b7b05835fe547dc6fade9407 |
|
01-Oct-2010 |
Darrick J. Wong <djwong@us.ibm.com> |
[SCSI] libsas: Don't issue commands to devices that have been hot-removed sd will get hung up issuing commands to flush write cache if a SAS device behind the expander is unplugged without warning. Change libsas to reject commands to domain devices that have already gone away. [maciej.trela@intel.com: removed setting ->gone in sas_deform_port() to permit sync cache commands at module removal] Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Tested-by: Haipao Fan <haipao.fan@intel.com> Signed-off-by: Maciej Trela <maciej.trela@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
df64d3caab8db6ae17dacd229a03d7689a10c432 |
|
27-Jul-2010 |
James Bottomley <James.Bottomley@suse.de> |
[SCSI] Unify SAM_ and SAM_STAT_ macros We have two separate definitions for identical constants with nearly the same name. One comes from the generic headers in scsi.h; the other is an enum in libsas.h ... it's causing confusion about which one is correct (fortunately they both are). Fix this by eliminating the libsas.h duplicate Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
5a0e3ad6af8660be21ca98a971cd00f331318c05 |
|
24-Mar-2010 |
Tejun Heo <tj@kernel.org> |
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
198439e4afec431d2fa2cab9a4dcca87e5adc7a5 |
|
20-Oct-2009 |
jack wang <jack_wang@usish.com> |
[SCSI] libsas: do not set res = 0 in sas_ex_discover_dev() We should not set res to 0 in function sas_ex_discover_dev in order to let it discover it further when wide port hotplug in . Signed-off-by: Tom Peng <tom_peng@usish.com> Signed-off-by: Jack Wang <jack_wang@usish.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de>
|
19252de6818ced0def0551d64a0a2975f52a523d |
|
17-Jul-2009 |
Tom Peng <tom_peng@usish.com> |
[SCSI] libsas: fix wide port hotplug issues Hotplug of phys which form wide ports simply does not work at the moment. Fix this by adding checks at the hotplug points to see if the attached sas address of the phy already exists (in which case it's part of a wide port) and act accordingly. Signed-off-by: Tom Peng <tom_peng@usish.com> Signed-off-by: Jack Wang <jack_wang@usish.com> Signed-off-by: Lindar Liu <lindar_liu@usish.com> Signed-off-by: Kevin Ao <aoqingyun@usish.com> [jejb: tidied up coding, fixed an error case and made TRUE/FALSE lower case to fix a ppc64 compile error in linux-next] Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
5f49f63178360b07a095bd33b0d850d60edf7590 |
|
19-May-2009 |
Tejun Heo <tj@kernel.org> |
block: set rq->resid_len to blk_rq_bytes() on issue In commit c3a4d78c580de4edc9ef0f7c59812fb02ceb037f, while introducing rq->resid_len, the default value of residue count was changed from full count to zero. The conversion was done under the assumption that when a request fails residue count wasn't defined. However, Boaz and James pointed out that this wasn't true and the residue count should be preserved for failed requests too. This patchset restores the original behavior by setting rq->resid_len to blk_rq_bytes(rq) on request start and restoring explicit clearing in affected drivers. While at it, take advantage of the fact that rq->resid_len is set to full count where applicable. * ide-cd: rq->resid_len cleared on pc success * mptsas: req->resid_len cleared on success * sas_expander: rsp/req->resid_len cleared on success * mpt2sas_transport: req->resid_len cleared on success * ide-cd, ide-tape, mptsas, sas_host_smp, mpt2sas_transport, ub: take advantage of initial full count to simplify code Boaz Harrosh spotted bug in resid_len initialization. Fixed as suggested. Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: Borislav Petkov <petkovbb@googlemail.com> Cc: Boaz Harrosh <bharrosh@panasas.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Pete Zaitcev <zaitcev@redhat.com> Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Eric Moore <Eric.Moore@lsi.com> Cc: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
b0790410300abaaf4f25f702803beff701baebf1 |
|
07-May-2009 |
Tejun Heo <tj@kernel.org> |
block: cleanup rq->data_len usages With recent unification of fields, it's now guaranteed that rq->data_len always equals blk_rq_bytes(). Convert all non-IDE direct users to accessors. IDE will be converted in a separate patch. Boaz: spotted incorrect data_len/resid_len conversion in osd. [ Impact: convert direct rq->data_len usages to blk_rq_bytes() ] Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Pete Zaitcev <zaitcev@redhat.com> Cc: Eric Moore <Eric.Moore@lsi.com> Cc: Markus Lidel <Markus.Lidel@shadowconnect.com> Cc: Darrick J. Wong <djwong@us.ibm.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Eric Moore <Eric.Moore@lsi.com> Cc: Boaz Harrosh <bharrosh@panasas.com> Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
c3a4d78c580de4edc9ef0f7c59812fb02ceb037f |
|
07-May-2009 |
Tejun Heo <tj@kernel.org> |
block: add rq->resid_len rq->data_len served two purposes - the length of data buffer on issue and the residual count on completion. This duality creates some headaches. First of all, block layer and low level drivers can't really determine what rq->data_len contains while a request is executing. It could be the total request length or it coulde be anything else one of the lower layers is using to keep track of residual count. This complicates things because blk_rq_bytes() and thus [__]blk_end_request_all() relies on rq->data_len for PC commands. Drivers which want to report residual count should first cache the total request length, update rq->data_len and then complete the request with the cached data length. Secondly, it makes requests default to reporting full residual count, ie. reporting that no data transfer occurred. The residual count is an exception not the norm; however, the driver should clear rq->data_len to zero to signify the normal cases while leaving it alone means no data transfer occurred at all. This reverse default behavior complicates code unnecessarily and renders block PC on some drivers (ide-tape/floppy) unuseable. This patch adds rq->resid_len which is used only for residual count. While at it, remove now unnecessasry blk_rq_bytes() caching in ide_pc_intr() as rq->data_len is not changed anymore. Boaz : spotted missing conversion in osd Sergei : spotted too early conversion to blk_rq_bytes() in ide-tape [ Impact: cleanup residual count handling, report 0 resid by default ] Signed-off-by: Tejun Heo <tj@kernel.org> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Cc: Borislav Petkov <petkovbb@googlemail.com> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Mike Miller <mike.miller@hp.com> Cc: Eric Moore <Eric.Moore@lsi.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: Doug Gilbert <dgilbert@interlog.com> Cc: Mike Miller <mike.miller@hp.com> Cc: Eric Moore <Eric.Moore@lsi.com> Cc: Darrick J. Wong <djwong@us.ibm.com> Cc: Pete Zaitcev <zaitcev@redhat.com> Cc: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
cadbd4a5e36dde7e6c49b587b2c419103c0b7218 |
|
04-Jul-2008 |
Harvey Harrison <harvey.harrison@gmail.com> |
[SCSI] replace __FUNCTION__ with __func__ [jejb: fixed up a ton of missed conversions. All of you are on notice this has happened, driver trees will now need to be rebased] Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Cc: SCSI List <linux-scsi@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
32e8ae36b8f80372015b88b63c4358a376c9af0f |
|
30-Dec-2007 |
James Bottomley <James.Bottomley@HansenPartnership.com> |
[SCSI] libsas: don't use made up error codes This is bad for two reasons: 1. If they're returned to outside applications, no-one knows what they mean. 2. Eventually they'll clash with the ever expanding standard error codes. The problem error code in question is ETASK. I've replaced this by ECOMM (communications error on send) a network error code that seems to most closely relay what ETASK meant. Acked-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
2d4b63e1505b317d4253cee3f2970792ec6d41cb |
|
29-Dec-2007 |
James Bottomley <James.Bottomley@HansenPartnership.com> |
[SCSI] libsas: don't treat underrun as an error on SMP tasks All SMP tasks sent through bsg generate messages like: sas: smp_execute_task: task to dev 500605b000001450 response: 0x0 status 0x81 Three times (because the task gets retried). Firstly, don't retry either overrun or underrun (the data buffer isn't going to change size) and secondly, just report the underrun but don't set an error for it. This is necessary so bsg can report back the residual. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
b98e66fa0b687149dc3b26179096dc542c7d5001 |
|
28-Dec-2007 |
James Bottomley <James.Bottomley@HansenPartnership.com> |
[SCSI] libsas: add host SMP processing This adds support for host side SMP processing, via a separate SMP interpreter file. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
5929faf3334f4c69f3bb02be59d7c127e0cefa1f |
|
05-Nov-2007 |
Darrick J. Wong <djwong@us.ibm.com> |
[SCSI] libsas: Convert sas_proto users to sas_protocol sparse complains about the mixing of enums in libsas. Since the underlying numeric values of both enums are the same, combine them to get rid of the warning. Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
92631fa4d0afa64b82144eab714fbf2f4049dabe |
|
28-Jul-2007 |
Jesper Juhl <jesper.juhl@gmail.com> |
[SCSI] libsas: Fix potential NULL dereference in sas_smp_get_phy_events() In sas_smp_get_phy_events() we never test if the call to alloc_smp_req(RPEL_REQ_SIZE) succeeds or fails. That means we run the risk of dereferencing a NULL pointer if it does fail. Far better to test if we got NULL back and in that case return -ENOMEM just as we already do for the other memory allocation in that function. Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
2cd614c8732172524c36cd5245620338928062b6 |
|
24-Jul-2007 |
Darrick J. Wong <djwong@us.ibm.com> |
[SCSI] libsas: SMP request handler shouldn't crash when rphy is NULL sas_smp_handler crashes when smp utils are used with an aic94xx host because certain devices (the sas_host itself, specifically) lack rphy structures. No rphy means no SMP target support, but we shouldn't crash here. Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
b91421749a1840148d8c81637c03c0ace3f35269 |
|
22-Jul-2007 |
James Bottomley <James.Bottomley@steeleye.com> |
[SCSI] libsas: make ATA functions selectable by a config option Not everyone wants libsas automatically to pull in libata. This patch makes the behaviour configurable, so you can build libsas with or without ATA support. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
08547354c17a50a54906b7936d6ecb05ea39bedd |
|
07-Jul-2007 |
FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> |
[SCSI] libsas: kill unused smp_portal code Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
ba1fc175cc6c0af7e78241e50160344f0f198282 |
|
08-Jul-2007 |
FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> |
[SCSI] libsas: add SAS management protocol handler This patch adds support for SAS Management Protocol (SMP) passthrough support via bsg. aic94xx can use this. Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
9d720d82dc295521d70939c3f5edd54050730f09 |
|
16-Jul-2007 |
James Bottomley <James.Bottomley@steeleye.com> |
[SCSI] libsas: fix lockdep issue with ATA lockdep noticed that with ATA support the port->dev_list_lock was entangled at irq context, so it now needs to become IRQ safe Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
528fd55200ec135548e71aee43650bca92a041aa |
|
16-Oct-2006 |
James Bottomley <James.Bottomley@steeleye.com> |
[SCSI] libsas: better error handling in sas_ex_discover_end_dev() This replaces a few BUG_ON() statements with the correct failure error handling. There are still many more to do. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
38e2f035587b0674b3168931c8402f4d719fdd76 |
|
07-Sep-2006 |
James Bottomley <jejb@mulgrave.il.steeleye.com> |
[SCSI] libsas: fix up sas_smp_phy_control() The prototype of this has changed for the link speed setting patch. Need to update the SATA use of this. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
1acce1942a32296f7c25ba82776c97e9c04c8e1e |
|
22-Aug-2006 |
James Bottomley <James.Bottomley@HansenPartnership.com> |
[SCSI] libsas: Add SATA support to STP piece for SATA on SAS expanders This patch adds support for SATA over SAS expanders to the previous two SATA support in libsas patches. There were a couple of nasty non trivial things to sort out before this one could be made to work. Firstly, I'd like to thank Doug Gilbert for diagnosing a problem with the LSI expanders where the REPORT_SATA_PHY command was returning the D2H FIS in the wrong order (Although, here, I think I have to blame the SAS standards which specifies the FIS "shall be returned in little endian format" and later on "which means resp[24] shall be FIS type" The latter, of course, implying big endian format). Just to make sure, I put a check for the D2H FIS type being in the wrong position and reverse the FIS data if it is. The second is a problem outlined in Annex G of the SAS standard (again, a technical point with D2H FIS ... necessitating a phy reset on certain conditions). With the patch, I can now see my SATA-1 disk in a cascaded expander configuration. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
91a6902958f052358899f58683d44e36228d85c2 |
|
09-Jun-2007 |
Zhang Rui <rui.zhang@intel.com> |
sysfs: add parameter "struct bin_attribute *" in .read/.write methods for sysfs binary attributes Well, first of all, I don't want to change so many files either. What I do: Adding a new parameter "struct bin_attribute *" in the .read/.write methods for the sysfs binary attributes. In fact, only the four lines change in fs/sysfs/bin.c and include/linux/sysfs.h do the real work. But I have to update all the files that use binary attributes to make them compatible with the new .read and .write methods. I'm not sure if I missed any. :( Why I do this: For a sysfs attribute, we can get a pointer pointing to the struct attribute in the .show/.store method, while we can't do this for the binary attributes. I don't know why this is different, but this does make it not so handy to use the binary attributes as the regular ones. So I think this patch is reasonable. :) Who benefits from it: The patch that exposes ACPI tables in sysfs requires such an improvement. All the table binary attributes share the same .read method. Parameter "struct bin_attribute *" is used to get the table signature and instance number which are used to distinguish different ACPI table binary attributes. Without this parameter, we need to offer different .read methods for different ACPI table binary attributes. This is impossible as there are various ACPI tables on different platforms, and we don't know what they are until they are loaded. Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
7b595756ec1f49e0049a9e01a1298d53a7faaa15 |
|
13-Jun-2007 |
Tejun Heo <htejun@gmail.com> |
sysfs: kill unnecessary attribute->owner sysfs is now completely out of driver/module lifetime game. After deletion, a sysfs node doesn't access anything outside sysfs proper, so there's no reason to hold onto the attribute owners. Note that often the wrong modules were accounted for as owners leading to accessing removed modules. This patch kills now unnecessary attribute->owner. Note that with this change, userland holding a sysfs node does not prevent the backing module from being unloaded. For more info regarding lifetime rule cleanup, please read the following message. http://article.gmane.org/gmane.linux.kernel/510293 (tweaked by Greg to not delete the field just yet, to make it easier to merge things properly.) Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Cornelia Huck <cornelia.huck@de.ibm.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
6473d160b4aba8023bcf38519a5989694dfd51a7 |
|
06-Mar-2007 |
Jean Delvare <khali@linux-fr.org> |
PCI: Cleanup the includes of <linux/pci.h> I noticed that many source files include <linux/pci.h> while they do not appear to need it. Here is an attempt to clean it all up. In order to find all possibly affected files, I searched for all files including <linux/pci.h> but without any other occurence of "pci" or "PCI". I removed the include statement from all of these, then I compiled an allmodconfig kernel on both i386 and x86_64 and fixed the false positives manually. My tests covered 66% of the affected files, so there could be false positives remaining. Untested files are: arch/alpha/kernel/err_common.c arch/alpha/kernel/err_ev6.c arch/alpha/kernel/err_ev7.c arch/ia64/sn/kernel/huberror.c arch/ia64/sn/kernel/xpnet.c arch/m68knommu/kernel/dma.c arch/mips/lib/iomap.c arch/powerpc/platforms/pseries/ras.c arch/ppc/8260_io/enet.c arch/ppc/8260_io/fcc_enet.c arch/ppc/8xx_io/enet.c arch/ppc/syslib/ppc4xx_sgdma.c arch/sh64/mach-cayman/iomap.c arch/xtensa/kernel/xtensa_ksyms.c arch/xtensa/platform-iss/setup.c drivers/i2c/busses/i2c-at91.c drivers/i2c/busses/i2c-mpc.c drivers/media/video/saa711x.c drivers/misc/hdpuftrs/hdpu_cpustate.c drivers/misc/hdpuftrs/hdpu_nexus.c drivers/net/au1000_eth.c drivers/net/fec_8xx/fec_main.c drivers/net/fec_8xx/fec_mii.c drivers/net/fs_enet/fs_enet-main.c drivers/net/fs_enet/mac-fcc.c drivers/net/fs_enet/mac-fec.c drivers/net/fs_enet/mac-scc.c drivers/net/fs_enet/mii-bitbang.c drivers/net/fs_enet/mii-fec.c drivers/net/ibm_emac/ibm_emac_core.c drivers/net/lasi_82596.c drivers/parisc/hppb.c drivers/sbus/sbus.c drivers/video/g364fb.c drivers/video/platinumfb.c drivers/video/stifb.c drivers/video/valkyriefb.c include/asm-arm/arch-ixp4xx/dma.h sound/oss/au1550_ac97.c I would welcome test reports for these files. I am fine with removing the untested files from the patch if the general opinion is that these changes aren't safe. The tested part would still be nice to have. Note that this patch depends on another header fixup patch I submitted to LKML yesterday: [PATCH] scatterlist.h needs types.h http://lkml.org/lkml/2007/3/01/141 Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Badari Pulavarty <pbadari@us.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
423f7cf467045eab616f97309aed87a54b5e351d |
|
30-Jan-2007 |
Darrick J. Wong <djwong@us.ibm.com> |
[SCSI] libsas: Don't BUG when connecting two expanders via wide port libsas: Don't BUG when connecting two expanders via wide port When a device is connected to an expander, the discovery process goes through sas_ex_discover_dev to figure out what's attached to the phy. If it is the case that the phy being discovered happens to be the second phy of a wide link to an expander, that discover_dev function will incorrectly call sas_ex_discover_expander, which creates another sas_port and tries to attach the other sas_phys to the new port, thus triggering a BUG. The correct thing to do is to check the other ex_phys of the expander to see if there's a sas_port for this sas_phy, and attach the sas_phy to the existing sas_port. This is easily triggered if one enables the phys of a wide port between expanders one by one. This second version of the patch fixes a small regression in the case where all the phys show up at once and we accidentally try to attach to a port that hasn't been created yet. Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
6f63caae2172e97e528b58319480217b0b36542e |
|
26-Jan-2007 |
Darrick J. Wong <djwong@us.ibm.com> |
[SCSI] libsas: Clean up discovery failure handler code sas_rphy_delete does two things: it removes the sas_rphy from the transport layer and frees the sas_rphy. This can be broken down into two functions, sas_rphy_remove and sas_rphy_free; sas_rphy_remove is of interest to sas_discover_root_expander because it calls functions that require sas_rphy_add as a prerequisite and can fail (namely sas_discover_expander). In that case, sas_discover_root_expander needs to be able to undo the effects of sas_rphy_add yet leave the job of freeing the sas_rphy to the caller of sas_discover_root_expander. This patch also removes some unnecessary code from sas_discover_end_dev to eliminate an unnecessary cycle of sas_notify_lldd_gone/found for SAS devices, thus eliminating a sas_rphy_remove call (and fixing a race condition where a SCSI target scan can come in between the gone and found call). It also moves the sas_rphy_free calls into sas_discover_domain and sas_ex_discover_end_dev to complement the sas_rphy_allocation via sas_get_port_device. This patch does not change the semantics of sas_rphy_delete. Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
bf451207511d049189ddb0a4eae3acdb086a3c82 |
|
11-Jan-2007 |
Darrick J. Wong <djwong@us.ibm.com> |
[SCSI] libsas: Clean up rphys/port dev list after a discovery error on an expander sas_get_port_device assigns a rphy to a domain device in anticipation of finding a disk. When a discovery error occurs in sas_discover_{sata,sas,expander}*, however, we need to clean up that rphy and the port device list so that we don't GPF. In addition, we need to check the result of the second sas_notify_lldd_dev_found. This patch seems ok on a x260, x366 and x206m. This patch fixes up sas_expander.c separately because jejb has some cleanup patches of his own that are a prerequisite. Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
024879ead9594acab30ce9e23c955086e2d967a0 |
|
16-Nov-2006 |
James Bottomley <James.Bottomley@steeleye.com> |
[SCSI] libsas: better error handling in sas_expander.c With async scanning, we're now tripping the BUG_ON in sas_ex_discover_end_dev(), so make the error handling here correct. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
42961ee8fc4b05f5ca4d96ab34abd5149afe3541 |
|
05-Oct-2006 |
malahal@us.ibm.com <malahal@us.ibm.com> |
[SCSI] aic94xx SCSI timeout fix: SMP retry fix. Updating DDB0 inside aic94xx driver itself caused SMP command timeout. I hit this SMP timeout problem twice but I am not able to reproduce it since then. Here is a fix that retries an SMP command. Signed-off-by: Malahal Naineni <malahal@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
a01e70e570a72b8a8c9a58062e4f5bdcd3986222 |
|
07-Sep-2006 |
James Bottomley <James.Bottomley@steeleye.com> |
[SCSI] aci94xx: implement link rate setting This patch implements the ability to set the minimum and maximum linkrates for both libsas (for expanders) and aic94xx (for the host phys). It also tidies up the setting of the hardware min and max to make sure they're updated when the expander emits a change broadcast. Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
88edf74610bd894b93438f389688bc8b4a2d3414 |
|
07-Sep-2006 |
James Bottomley <James.Bottomley@steeleye.com> |
[SCSI] SAS: consolidate linkspeed definitions At the moment we have two separate linkspeed enumerations covering roughly the same values. This patch consolidates on a single one enum sas_linkspeed in scsi_transport_sas.h and uses it everywhere in the aic94xx driver. Eventually I'll get around to removing the duplicated fields in asd_sas_phy and sas_phy ... Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
2908d778ab3e244900c310974e1fc1c69066e450 |
|
29-Aug-2006 |
James Bottomley <James.Bottomley@SteelEye.com> |
[SCSI] aic94xx: new driver This is the end point of the separate aic94xx driver based on the original driver and transport class from Luben Tuikov <ltuikov@yahoo.com> The log of the separate development is: Alexis Bruemmer: o aic94xx: fix hotplug/unplug for expanderless systems o aic94xx: disable split completion timer/setting by default o aic94xx: wide port off expander support o aic94xx: remove various inline functions o aic94xx: use bitops o aic94xx: remove queue comment o aic94xx: remove sas_common.c o aic94xx: sas remove depot's o aic94xx: use available list_for_each_entry_safe_reverse() o aic94xx: sas header file merge James Bottomley: o aic94xx: fix TF_TMF_NO_CTX processing o aic94xx: convert to request_firmware interface o aic94xx: fix hotplug/unplug o aic94xx: add link error counts to the expander phys o aic94xx: add transport class phy reset capability o aic94xx: remove local_attached flag o Remove README o Fixup Makefile variable for libsas rename o Rename sas->libsas o aic94xx: correct return code for sas_discover_event o aic94xx: use parent backlink port o aic94xx: remove channel abstraction o aic94xx: fix routing algorithms o aic94xx: add backlink port o aic94xx: fix cascaded expander properties o aic94xx: fix sleep under lock o aic94xx: fix panic on module removal in complex topology o aic94xx: make use of the new sas_port o rename sas_port to asd_sas_port o Fix for eh_strategy_handler move o aic94xx: move entirely over to correct transport class formulation o remove last vestages of sas_rphy_alloc() o update for eh_timed_out move o Preliminary expander support for aic94xx o sas: remove event thread o minor warning cleanups o remove last vestiges of id mapping arrays o Further updates o Convert aic94xx over entirely to the transport class end device and o update aic94xx/sas to use the new sas transport class end device o [PATCH] aic94xx: attaching to the sas transport class o Add missing completion removal from prior patch o [PATCH] aic94xx: attaching to the sas transport class o Build fixes from akpm Jeff Garzik: o [scsi aic94xx] Remove ->owner from PCI info table Luben Tuikov: o initial aic94xx driver Mike Anderson: o aic94xx: fix panic on module insertion o aic94xx: stub out SATA_DEV case o aic94xx: compile warning cleanups o aic94xx: sas_alloc_task o aic94xx: ref count update o aic94xx nexus loss time value o [PATCH] aic94xx: driver assertion in non-x86 BIOS env Randy Dunlap: o libsas: externs not needed Robert Tarte: o aic94xx: sequence patch - fixes SATA support Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|